Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not each ath10k FW track supports P2P (10.X for instance does not)
This new firmware feature flag allows to turn off P2P interface type.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the interface limits and inteface combination,
to reflect the 10.X capabilites (no P2P, no STA and 8 VAP).
kvalo: reverse order of ATH10K_FW_FEATURE_WMI_10X test, fix
checkpath warnings
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Although CCK modulation isn't expected for 11a if
it happened it made ath10k report wrong band
(2GHz) for a mgmt frame that were actually
received on 5Ghz band. Frequency would also
decoded incorrectly too.
In case of 5GHz-only devices this triggered
mac80211 WARN_ON because there was no according
sband pointer to be found.
The patch should fix delivery of such frames by
using different means to acquire band parameter.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We should check MIC error flag base on
rx_attention, to have consistent status
of MIC failure and FCS error.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames received from FW were treated incorrectly.
This led to stations being unable to associate to
WEP Shared ath10k AP. This was indicated by a
bizarre hostapd message:
Unsupported authentication algorithm (36088)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW 10.1 seems to require the default key index to
be updated to point to group key after it is
installed. Otherwise Txed frames are corrupted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Too much of tx info was being cleared. This caused
issues in some setups with tx frame status
reporting.
This should fix some cases of stations not being
able to associate to ath10k AP.
Reported-By: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing and debugging.
This introduces new ath10k_pci module parameter
`irq_mode`. By default it is 0, meaning automatic
irq mode (MSI-X as long as both target HW and host
platform supports it). The parameter works on a
best effort basis.
kvalo: fix typo "ayto"
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible for FW to panic during early boot.
The patch re-introduces support to detect and
print those crashes.
This introduces an additional irq handler that is
set for the duration of early boot and shutdown.
The handler is then overriden with regular
handlers upon hif start().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation for code re-use. Also use ioread/write
wrappers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's impossible to rely on disable_irq() and/or CE
interrupt masking with legacy shared interrupts.
Other devices sharing the same irq line may assert
it while ath10k is doing something that requires
no interrupts.
Irq handlers are now registered after all
preparations are complete so spurious/foreign
interrupts won't do any harm. The handlers are
unregistered when no interrupts are required (i.e.
during driver teardown).
This also removes the ability to receive FW early
indication (since interrupts are not registered
until early boot is complete). This is not mission
critical (it's more of a hint that early boot
failed due to unexpected FW crash) and will be
re-added in a follow up patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function did a couple of things: it allocated
CE completions, registered CE callbacks and
enabled CE interrupts through HW registers.
This cannot be so. Split the function into one
that allocates CE completions and the other one
that starts off CE operation.
This is required for future legacy shared
interrupt handling.
This also fixes possible memory leak if post rx
failed.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary for interrupts to be
used for BMI. BMI already assumes there's only one
caller at a time and it works directly with CE.
Make BMI poll for CE completions instead of
waiting for interrupts. This makes disabling
interrupts during early boot possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware waits until host signals whether it has
chosen MSI(-X) or shared legacy interrupts. It is
not required for the driver to register interrupt
handlers immediately.
This patch prepares the pci irq code for more
changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k assumed all interrupts were directed to it.
This isn't the case for legacy shared interrupts.
ath10k consumed interrupts for other devices.
Check device irq status and return IRQ_NONE when
appropriate.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can show the same amount of information in one line. And then
it's easier to show this information only during first firmware boot
(see next patch).
For UART printouts there's already a message when they are enabled so
no need to have a print when they are disabled, that's the default
anyway.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Convert the MSI failure warnings to a debug message to make them less spammy.
Also convert the irq mode printout to a single print to make it easier to
show it only once.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.
By default radar detected event in not blocked.
To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure interface combination for AP running on channels
where radar detection is required. It allows only one type
of interface - AP on DFS channel and limits number of AP
interfaces to 8. Setup WMI channel flags accordingly to mac
channel configuration. CAC based on additional monitor vdev
is started if required for current channel.
kvalo: dropped ATH10K_DFS_CERTIFIED config option as this
the DFS still depends on few mac80211 and cfg80211 patches
which are on mac80211-next.git right now. The config option
will be added later once all dependencies are available.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Garbage was reported in ieee80211_tx_info. This
led to a WARN_ON in cfg80211_calculate_bitrate().
This also fixes some random tx bitrate values
reported through `iw` command.
Reported-By: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was obseverd many times the short queue limit can be
easily exceeded in case of AP multiple BSSID scenarios.
"ath10k: wmi mgmt_tx queue limit reached."
This was leading to TX packets drops.
This patch expands the queue limit to 128. After many stress
experiments (high traffic and lot of management frames in
the air) the new value seems to fix the problem on platforms
with limited resources.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With commit 0cfcefef1 ("mac80211: support reporting A-MSDU subframes
individually") there's no need to have the hack to clear the retry bit in
ath10k_htt_rx_amsdu(), mac80211 can handle this properly now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames were never retransmitted with
different/lower bandwidths, e.g. only 80MHz
bandwidth was used when dealing with a VHT80
peer.
Allow HW rate control to try out different
bandwidths when retransmitting. This increases
robustness.
Also, document the parameter properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HIF was not stopped properly in
ath10k_core_start() upon failure. This could cause
memory leaks of CE completions entries and
possibly other issues as well.
Move the HIF start/stop out of
ath10k_htc_wait_target(). The ctl_resp completion
is already prepared in ath10k_htc_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should make sure the device won't issue any
interrupts nor access any memory after the driver
is stopped/freed thus avoid memory corruption in
some cases.
Reported-By: Ben Greear <greearb@candelatech.com>
Reported-By: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing error reporting and adjust other
prints to make everything more consistent.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves irq registering after necessary
structures have been allocated and initialized.
This should prevent interrupts from causing
tasklet access invalid memory pointers.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware crashes it may report CE
completions for entries that were never
submitted/filled with meaningful data. This in
turn led to NULL dereferences.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This shouldn't be silenced. This will be necessary
for PCI init code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This removes some remaining direct use of the wake
register which could interfere with power state
tracking of the target device. This will allow
initialization code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check doesn't make much sense. If the address
were to be 0x0000 the check would fail. In this
case a 0 address isn't wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to put target back to sleep. This was a
minor issue as it didn't really matter if we put
target back to sleep at this point. It just looked
wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE error interrupts were not disabled. This could
lead to invalid memory accesses / memory
corruption.
Also make sure CE watermark interrupts are also
disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
What the function does is to actually wait for the
firmware indication bit to be set. Prerequisite
for this is having interrupts registered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville