These drivers work on our other FPGAs, for example the non-SoC PolarFire
connected to an FU-540 via chiplink. Make the entry a wee bit more
generic to match. While at it, remove the / from the heading so that it
matches other, neighbouring RISC-V entries.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221109212219.1598355-3-conor@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Following some discussion both on & off list, I have volunteered to take
over maintaining the miscellaneous RISC-V devicetrees & soc drivers from
Palmer to ease his load.
So far only SiFive and Microchip have stuff in drivers/soc. For the
former, a SiFive entry exists with a dead GitHub repo - so remove that
to avoid confusion since the patches for drivers/soc & devicetrees will
be routed via my tree & other drivers go through their subsystem trees.
The Microchip directory only contains a RISC-V driver for now, but is
likely to contain drivers for other archs in the future. To that end,
change the PolarFire SoC entry to specifically mention the RISC-V driver
& the new directory level entry does not mention an architecture.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Palmer Dabbelt <palmer@dabbelt.com>
Link: https://lore.kernel.org/linux-riscv/mhng-e4210f56-fcc3-4db8-abdb-d43b3ebe695d@palmer-ri-x1c9a/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221109212219.1598355-2-conor@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It contains:
- signal name fix for a pin on SAMA7G5
- memory self-refresh fix for SAMA7G5 by avoid soft resetting AC
DLL which can introduce glitches in RAM controller and lead to
unexpected behavior
- led support fix for lan966x-pcb8291 board by enabling sgpio node
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTsZ8eserC1pmhwqDmejrg/N2X7/QUCY2zi+AAKCRCejrg/N2X7
/RyZAQD0sVokdA9MKnPaap8zuXMnZd5yrQ7YMRYDn1puIscY3wEA98lZHOKlvVLW
+Ap3IUuFIEVwcrrIBGq7AZ0vIJjqxAE=
=uGGN
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=LTV+
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes for 6.1
It contains:
- signal name fix for a pin on SAMA7G5
- memory self-refresh fix for SAMA7G5 by avoid soft resetting AC
DLL which can introduce glitches in RAM controller and lead to
unexpected behavior
- led support fix for lan966x-pcb8291 board by enabling sgpio node
* tag 'at91-fixes-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: pm: avoid soft resetting AC DLL
ARM: dts: lan966x: Enable sgpio on pcb8291
ARM: dts: at91: sama7g5: fix signal name of pin PB2
Link: https://lore.kernel.org/r/20221110115411.180876-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes the APCS register region on IPQ8074 to not overlap
with adjacent nodes.
It lists the valid LDO modes on a variety of platforms, as this is not
required by the binding and implementation.
The reference clocks for the two UFS instances on SC8280XP are
corrected, to avoid relying on the state left by most versions of the
bootloader.
A number of issues are corrected with regards to the QMP PHY register
ranges on SC8280XP.
SC7280 gains a missing lpass reset region.
Lastly cluster idle is termporarily disabled on SM8250 to avoid issues
with booting the platform, until the last missing pieces lands.
-----BEGIN PGP SIGNATURE-----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=dJ0E
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=JYBF
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DTS fixes for 6.1
This fixes the APCS register region on IPQ8074 to not overlap
with adjacent nodes.
It lists the valid LDO modes on a variety of platforms, as this is not
required by the binding and implementation.
The reference clocks for the two UFS instances on SC8280XP are
corrected, to avoid relying on the state left by most versions of the
bootloader.
A number of issues are corrected with regards to the QMP PHY register
ranges on SC8280XP.
SC7280 gains a missing lpass reset region.
Lastly cluster idle is termporarily disabled on SM8250 to avoid issues
with booting the platform, until the last missing pieces lands.
* tag 'qcom-arm64-fixes-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8250: Disable the not yet supported cluster idle state
arm64: dts: qcom: sc7280: Add the reset reg for lpass audiocc on SC7280
arm64: dts: qcom: sc8280xp: fix UFS PHY serdes size
arm64: dts: qcom: sc8280xp: drop broken DP PHY nodes
arm64: dts: qcom: sc8280xp: fix USB PHY PCS registers
arm64: dts: qcom: sc8280xp: fix USB1 PHY RX1 registers
arm64: dts: qcom: sc8280xp: fix USB0 PHY PCS_MISC registers
arm64: dts: qcom: sc8280xp: correct ref clock for ufs_mem_phy
arm64: dts: qcom: sc8280xp: fix ufs_card_phy ref clock
arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
arm64: dts: qcom: sc8280xp-crd: Specify which LDO modes are allowed
arm64: dts: qcom: sa8295p-adp: Specify which LDO modes are allowed
arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
Revert "arm64: dts: qcom: msm8996: add missing TCSR syscon compatible"
arm64: dts: qcom: ipq8074: correct APCS register space size
Link: https://lore.kernel.org/r/20221110040635.795921-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
-----BEGIN PGP SIGNATURE-----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=mi0I
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Armv8 Juno fix for v6.1
Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.
* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add thermal critical trip points
Link: https://lore.kernel.org/r/20221102140156.2758137-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAmNhCeoACgkQAEG6vDF+
4phtJg/+OrQgmkGgheCPkjdb3EROvzEZ2Kgd1PSfprDKVQmz34r+hkrS55mLXiOD
uHd9+9o8q/gtjLCHiKLa0IBQDxxz29dJpvnNV+QyqnSw7o1D9E5DxM97cGkBCETv
lHfSC3SsHrI7CjnfAn05g4Lj8Rwv8T5P+/qpY2WpQzBMlcUdQOqjHOPjM2FMV8vh
/hzILxM3PENflAHjMlenB/bPjmV61sy/lPpoivay+D66IR6aEzrYN+p4kGdMZONH
ip2iEMrL1981giueQXlatv6ynKVTgRmT2Zvr0kSJDOaIxtBnoUNtycnSI8nsY5WF
r/Tdk2vEk4DF5p6m/n79g4LLqDsmJxtro9UuVQztYp5ztmpLENBmqZY2aRzl2xmh
XwzFKE0nX/maLJr4WsFYkjeeUII4RnhNGJtuyNRHVUChb4A8TQPrbGGXZqUD3Hs9
h3Xz3l2kvhVIQLs+foT8LQHjOlMxSRS+vjiyIu/3AtrvWmcVXZLRdmSFVsVWyfgg
QM/j3X2dqvk4fioq7QSJ/V5Bw0BeGNcaEZnRlaNZt3DaoYGlsd3uJX6zwh0twNRz
iOm4Xf3KZZ7oFKxt3LqYxlezb8dy5aJqvwKb7VX4KieOjEsyHw3RRf4N6XF4V75z
rvaRXuAyyTf8nWuZ6clcNevrFvFtR6UTdrzszxSW8Ynm0CXgSwI=
=9hru
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=jNDG
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fixes for v6.1
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
* tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix deferred_tx_wq release on error paths
firmware: arm_scmi: Fix devres allocation device in virtio transport
firmware: arm_scmi: Make Rx chan_setup fail on memory errors
firmware: arm_scmi: Make tx_prepare time out eventually
firmware: arm_scmi: Suppress the driver's bind attributes
firmware: arm_scmi: Cleanup the core driver removal callback
Link: https://lore.kernel.org/r/20221102140142.2758107-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When thermnal zones are defined, trip points definitions are mandatory.
Define a couple of critical trip points for monitoring of existing
PMIC and SOC thermal zones.
This was lost between txt to yaml conversion and was re-enforced recently
via the commit 8c59632423 ("dt-bindings: thermal: Fix missing required property")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Fixes: f7b636a8d8 ("arm64: dts: juno: add thermal zones for scpi sensors")
Link: https://lore.kernel.org/r/20221028140833.280091-8-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use devres to allocate the dedicated deferred_tx_wq polling workqueue so
as to automatically trigger the proper resource release on error path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5a3b7185c4 ("firmware: arm_scmi: Add atomic mode support to virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI virtio transport device managed allocations must use the main
platform device in devres operations instead of the channel devices.
Cc: Peter Hilber <peter.hilber@opensynergy.com>
Fixes: 46abe13b5e ("firmware: arm_scmi: Add virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-5-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI Rx channels are optional and they can fail to be setup when not
present but anyway channels setup routines must bail-out on memory errors.
Make channels setup, and related probing, fail when memory errors are
reported on Rx channels.
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI transports based on shared memory, at start of transmissions, have
to wait for the shared Tx channel area to be eventually freed by the
SCMI platform before accessing the channel. In fact the channel is owned
by the SCMI platform until marked as free by the platform itself and,
as such, cannot be used by the agent until relinquished.
As a consequence a badly misbehaving SCMI platform firmware could lock
the channel indefinitely and make the kernel side SCMI stack loop
forever waiting for such channel to be freed, possibly hanging the
whole boot sequence.
Add a timeout to the existent Tx waiting spin-loop so that, when the
system ends up in this situation, the SCMI stack can at least bail-out,
nosily warn the user, and abort the transmission.
Reported-by: YaxiongTian <iambestgod@outlook.com>
Suggested-by: YaxiongTian <iambestgod@outlook.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-3-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Suppress the capability to unbind the core SCMI driver since all the
SCMI stack protocol drivers depend on it.
Fixes: aa4f886f38 ("firmware: arm_scmi: add basic driver infrastructure for SCMI")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Platform drivers .remove callbacks are not supposed to fail and report
errors. Such errors are indeed ignored by the core platform drivers
and the driver unbind process is anyway completed.
The SCMI core platform driver as it is now, instead, bails out reporting
an error in case of an explicit unbind request.
Fix the removal path by adding proper device links between the core SCMI
device and the SCMI protocol devices so that a full SCMI stack unbind is
triggered when the core driver is removed. The remove process does not
bail out anymore on the anomalous conditions triggered by an explicit
unbind but the user is still warned.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Recent changes to the thermal framework has made the trip
points (trips) for thermal zones compulsory, which made
the Ux500 DTS files break validation and also stopped
probing because of similar changes to the code.
Fix this by adding an "outer bounding box": battery thermal
zones should not get warmer than 70 degress, then we will
shut down.
Fixes: 8c59632423 ("dt-bindings: thermal: Fix missing required property")
Fixes: 3fd6d6e2b4 ("thermal/of: Rework the thermal device tree initialization")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Link: https://lore.kernel.org/r/20221030210854.346662-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix imx93-pd driver to release resources when error occurs in probe.
- A series from Ioana Ciornei to add missing clock frequencies for MDIO
controllers on LayerScape SoCs, so that the kernel driver can work
independently from bootloader.
- A series from Li Jun to fix USB power domain setup in i.MX8MM/N device
trees.
- Fix CPLD_Dn pull configuration for MX8Menlo board to avoid interfering
with CPLD power off functionality.
- Fix ctrl_sleep_moci GPIO setup for verdin-imx8mp board.
- Fix DT schema check warnings on uSDHC clocks for imx8-ss-conn device
tree.
- Fix up gpcv2 DT bindings to have an optional `power-domains` property.
- A couple of i.MX93 device tree fixes on S4MU interrupt and gpio-ranges
of GPIO controllers.
- Keep PU regulator on for Quad and QuadPlus based imx6dl-yapp4 boards to
work around a hardware design flaw in supply voltage distribution.
- Fix user push-button GPIO offset on imx6qdl-gw59 boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmNgjiEUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4anAgAmZ5lSvXKhlaYijN7DSh9WlpwDcf1
BRGAoT94d2C0rv1+lPKaEcSCJAo7/jqiMUgNorUVhlwR9frJIJK9HvNkfzJ66vQ9
DRksUZjomlIuefaOWdja18ZZD6WuPoe95pjW2ssB/A2zAmKYxtSoqiHsPfnzRtp1
yaBa1DyKBodVp+Eo0HT9Cyg1gBbPaHDex4D/v852UaBQ3J297phykeFrL/FjwsZT
ojAlK30sEb5LOBvcBnQxus1f0EhaB+sjapAsNMX0vaEkx49zO+fOEDa2I/vBXbA8
NF/jOf87pl9QeYkVDGKlP4EtTbXKObsVOfSFc05C1gT68FUGUbGF2pX/3g==
=YELK
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=W2eO
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.1:
- Fix imx93-pd driver to release resources when error occurs in probe.
- A series from Ioana Ciornei to add missing clock frequencies for MDIO
controllers on LayerScape SoCs, so that the kernel driver can work
independently from bootloader.
- A series from Li Jun to fix USB power domain setup in i.MX8MM/N device
trees.
- Fix CPLD_Dn pull configuration for MX8Menlo board to avoid interfering
with CPLD power off functionality.
- Fix ctrl_sleep_moci GPIO setup for verdin-imx8mp board.
- Fix DT schema check warnings on uSDHC clocks for imx8-ss-conn device
tree.
- Fix up gpcv2 DT bindings to have an optional `power-domains` property.
- A couple of i.MX93 device tree fixes on S4MU interrupt and gpio-ranges
of GPIO controllers.
- Keep PU regulator on for Quad and QuadPlus based imx6dl-yapp4 boards to
work around a hardware design flaw in supply voltage distribution.
- Fix user push-button GPIO offset on imx6qdl-gw59 boards.
* tag 'imx-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
soc: imx: imx93-pd: Fix the error handling path of imx93_pd_probe()
arm64: dts: imx93: correct gpio-ranges
arm64: dts: imx93: correct s4mu interrupt names
dt-bindings: power: gpcv2: add power-domains property
arm64: dts: imx8: correct clock order
ARM: dts: imx6dl-yapp4: Do not allow PM to switch PU regulator off on Q/QP
ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
arm64: dts: imx8mn: Correct the usb power domain
arm64: dts: imx8mn: remove otg1 power domain dependency on hsio
arm64: dts: imx8mm: correct usb power domains
arm64: dts: imx8mm: remove otg1/2 power domain dependency on hsio
arm64: dts: verdin-imx8mp: fix ctrl_sleep_moci
arm64: dts: imx8mm: Enable CPLD_Dn pull down resistor on MX8Menlo
Link: https://lore.kernel.org/r/20221101031547.GB125525@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Do not soft reset AC DLL as controller is buggy and this operation my
introduce glitches in the controller leading to undefined behavior.
Fixes: f0bbf17958 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: a02875c4cb ("ARM: at91: pm: fix self-refresh for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221026124114.985876-2-claudiu.beznea@microchip.com
Enable sgpio node on pcb8291 as this is needed to be able to control
the LEDs on this board. Otherwise the LEDs support on the board will
not be available.
On the other board pcb8309 the sgpio is already enabled because it
needed to access the SFP ports.
Fixes: 0b7baa1a30 ("ARM: dts: lan966x: add led configuration")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221026174303.702919-1-horatiu.vultur@microchip.com
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 0420dde30a ("arm64: dts: ls208xa: add the external MDIO nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: bbe75af7b0 ("arm64: dts: ls1088a: add external MDIO device nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.
Fixes: 6e1b8fae89 ("arm64: dts: lx2160a: add emdio1 node")
Fixes: 5705b9dcda ("arm64: dts: lx2160a: add emdio2 node")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In imx93_pd_probe(); if an error occurs, some resources need to be released
as done in the remove function.
Fixes: 0a0f7cc25d ("soc: imx: add i.MX93 SRC power domain driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc, interrupt names should be tx and rx.
Fixes: 0dfb380d24 ("arm64: dts: imx93: add s4 mu node")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some pgc power-domain requires a parent power domain, so
add an optional power-domains property, otherwise there will be
dt check warning:
gpc@303a0000: pgc:power-domain@1: 'power-domains' does not match
any of the regexes: 'pinctrl-[0-9]+'
Fixes: 30af8513bd ("dt-bindings: power: add defines for i.MX8MM power domains")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per bindings/mmc/fsl-imx-esdhc.yaml, the clock order is ipg, ahb, per,
otherwise warning: "
mmc@5b020000: clock-names:1: 'ahb' was expected
mmc@5b020000: clock-names:2: 'per' was expected "
Fixes: 16c4ea7501 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix our design flaw in supply voltage distribution on the Quad and QuadPlus
based boards.
The problem is that we supply the SoC cache (VDD_CACHE_CAP) from VDD_PU
instead of VDD_SOC. The VDD_PU internal regulator can be disabled by PM
if VPU or GPU is not used. If that happens the system freezes. To prevent
that configure the reg_pu regulator to be always on.
Fixes: 0de4ab81ab ("ARM: dts: imx6dl-yapp4: Add Y Soft IOTA Crux/Crux+ board")
Cc: petrben@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Petr Benes <petr.benes@ysoft.com>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW5910 and GW5913 have a user pushbutton that is tied to the
Gateworks System Controller GPIO offset 2. Fix the invalid offset of 0.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1 power domain
to the usb phy node.
Fixes: ea2b5af58a ("arm64: dts: imx8mn: put USB controller into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1 is an independent power domain of hsio, it's for usb phy,
so remove hsio power domain from its node.
Fixes: 8b8ebec673 ("arm64: dts: imx8mn: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1/2 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1/2 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1/2 power domain
to the usb phy node.
Fixes: 01df28d808 ("arm64: dts: imx8mm: put USB controllers into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pgc_otg1/2 are independent power domain of hsio, they for usb phy,
so remove hsio power domain dependency from its node.
Fixes: d39d4bb153 ("arm64: dts: imx8mm: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO signaling ctrl_sleep_moci is currently handled as a gpio hog.
But the gpio-hog node is made a child of the wrong gpio controller.
Move it to the node representing gpio4 so that it actually works.
Without this carrier board components jumpered to use the signal are
unconditionally switched off.
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To support the deeper cluster idle state for sm8250 platforms, some
additional synchronization is needed between the rpmh-rsc device and the
CPU cluster PM domain. Until that is supported, let's disable the cluster
idle state.
This fixes a problem that has been reported for the Qcom RB5 platform (see
below), but most likely other sm8250 platforms suffers from similar issues,
so let's make the fix generic for sm8250.
vreg_l11c_3p3: failed to enable: -ETIMEDOUT
qcom-rpmh-regulator 18200000.rsc:pm8150l-rpmh-regulators: ldo11: devm_regulator_register() failed, ret=-110
qcom-rpmh-regulator: probe of 18200000.rsc:pm8150l-rpmh-regulators failed with error -110
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Fixes: 32bc936d73 ("arm64: dts: qcom: sm8250: Add cpuidle states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027115745.240516-1-ulf.hansson@linaro.org
sections, please pull the following:
- Palmer updates the various Broadcom entries to use https instead of
git for the git trees listed
-----BEGIN PGP SIGNATURE-----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=wcuw
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=t6YQ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-6.1/maintainers-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains MAINTAINERS file updates for Broadcom
sections, please pull the following:
- Palmer updates the various Broadcom entries to use https instead of
git for the git trees listed
* tag 'arm-soc/for-6.1/maintainers-fixes' of https://github.com/Broadcom/stblinux:
MAINTAINERS: git://github -> https://github.com for broadcom
Link: https://lore.kernel.org/r/20221019185514.750684-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221017083119.1643-1-mihai.sain@microchip.com
- Fix compilation without RISCV_ISA_ZICBOM
- Fix kvm_riscv_vcpu_timer_pending() for Sstc
ARM:
- Fix a bug preventing restoring an ITS containing mappings
for very large and very sparse device topology
- Work around a relocation handling error when compiling
the nVHE object with profile optimisation
- Fix for stage-2 invalidation holding the VM MMU lock
for too long by limiting the walk to the largest
block mapping size
- Enable stack protection and branch profiling for VHE
- Two selftest fixes
x86:
- add compat implementation for KVM_X86_SET_MSR_FILTER ioctl
selftests:
- synchronize includes between include/uapi and tools/include/uapi
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmNT2hQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNeVwgAkGGk2F2SF5s+MQUQ9tDPxyuRbddN
NPo/YRTKszKc8rK6d1TCbQi56I3e8Oa7kNkMF7CiBlAekB7B1r1ySg5qc+3lQebx
moME30Ru4nmfqPcZ7971MA8Me7zZxGzvIviL5KIwm1ownGifdTsPZ9jCvu4EPdzv
3dd10guH3GeBIq8QeQGEqNP4fticziwhE+IA3HZstcWsq96800Le7WNAgklfzdC+
YTB81QU6whHv6N/7YvRcTbp+tER3VIKdFMmRD1FwC90flhXMbxTymESFXULfHCM2
x/arGz2E31/QGgJo0/Yy2VPenr5ZMU57dL4SYWR02mwSfJQnJWb1cRdWnw==
=rxQ7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"RISC-V:
- Fix compilation without RISCV_ISA_ZICBOM
- Fix kvm_riscv_vcpu_timer_pending() for Sstc
ARM:
- Fix a bug preventing restoring an ITS containing mappings for very
large and very sparse device topology
- Work around a relocation handling error when compiling the nVHE
object with profile optimisation
- Fix for stage-2 invalidation holding the VM MMU lock for too long
by limiting the walk to the largest block mapping size
- Enable stack protection and branch profiling for VHE
- Two selftest fixes
x86:
- add compat implementation for KVM_X86_SET_MSR_FILTER ioctl
selftests:
- synchronize includes between include/uapi and tools/include/uapi"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
tools: include: sync include/api/linux/kvm.h
KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
kvm: Add support for arch compat vm ioctls
RISC-V: KVM: Fix kvm_riscv_vcpu_timer_pending() for Sstc
RISC-V: Fix compilation without RISCV_ISA_ZICBOM
KVM: arm64: vgic: Fix exit condition in scan_its_table()
KVM: arm64: nvhe: Fix build with profile optimization
KVM: selftests: Fix number of pages for memory slot in memslot_modification_stress_test
KVM: arm64: selftests: Fix multiple versions of GIC creation
KVM: arm64: Enable stack protection and branch profiling for VHE
KVM: arm64: Limit stage2_apply_range() batch size to largest block
KVM: arm64: Work out supported block level at compile time
This reverts commit 72a9585972.
It broke reboots on big-endian MIPS and MIPS64 malta QEMU instances,
which use the syscon driver. Little-endian is not effected, which means
likely it's important to handle regmap_get_val_endian() in this function
after all.
Fixes: 72a9585972 ("mfd: syscon: Remove repetition of the regmap_get_val_endian()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Rework how SIGTRAPs get delivered to events to address a bunch of
problems with it. Add a selftest for that too
-----BEGIN PGP SIGNATURE-----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=DXG7
-----END PGP SIGNATURE-----
Merge tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Fix raw data handling when perf events are used in bpf
- Rework how SIGTRAPs get delivered to events to address a bunch of
problems with it. Add a selftest for that too
* tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bpf: Fix sample_flags for bpf_perf_event_output
selftests/perf_events: Add a SIGTRAP stress test with disables
perf: Fix missing SIGTRAPs
Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache allocation
on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration info
properly
- Drop a -mabi=ms compiler option check as both compilers support it now
anyway
- A couple of fixes to how the initial, statically allocated FPU buffer
state is setup and its interaction with dynamic states at runtime
-----BEGIN PGP SIGNATURE-----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=2hxy
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"As usually the case, right after a major release, the tip urgent
branches accumulate a couple more fixes than normal. And here is the
x86, a bit bigger, urgent pile.
- Use the correct CPU capability clearing function on the error path
in Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache
allocation on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration
info properly
- Drop a -mabi=ms compiler option check as both compilers support it
now anyway
- A couple of fixes to how the initial, statically allocated FPU
buffer state is setup and its interaction with dynamic states at
runtime"
* tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly
perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph()
x86/ftrace: Remove ftrace_epilogue()
x86/resctrl: Fix min_cbm_bits for AMD
x86/microcode/AMD: Apply the patch early on every logical thread
x86/topology: Fix duplicated core ID within a package
x86/topology: Fix multiple packages shown on a single-package system
hwmon/coretemp: Handle large core ID value
x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
x86/fpu: Exclude dynamic states from init_fpstate
x86/fpu: Fix the init_fpstate size check with the actual size
x86/fpu: Configure init_fpstate attributes orderly
-----BEGIN PGP SIGNATURE-----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=tTNe
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux
Pull io_uring follow-up from Jens Axboe:
"Currently the zero-copy has automatic fallback to normal transmit, and
it was decided that it'd be cleaner to return an error instead if the
socket type doesn't support it.
Zero-copy does work with UDP and TCP, it's more of a future proofing
kind of thing (eg for samba)"
* tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux:
io_uring/net: fail zc sendmsg when unsupported by socket
io_uring/net: fail zc send when unsupported by socket
net: flag sockets supporting msghdr originated zerocopy
Enable CPLD_Dn pull down resistor instead of pull up to avoid
intefering with CPLD power off functionality.
Fixes: 510c527b4f ("arm64: dts: imx8mm: Add i.MX8M Mini Toradex Verdin based Menlo board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- corsair-psu: Fix typo in USB id description, and add USB ID for new PSU
- pwm-fan: Fix fan power handling when disabling fan control
-----BEGIN PGP SIGNATURE-----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=ajp4
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- corsair-psu: Fix typo in USB id description, and add USB ID for new
PSU
- pwm-fan: Fix fan power handling when disabling fan control
* tag 'hwmon-for-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (corsair-psu) Add USB id of the new HX1500i psu
hwmon: (pwm-fan) Explicitly switch off fan power when setting pwm1_enable to 0
hwmon: (corsair-psu) fix typo in USB id description
-----BEGIN PGP SIGNATURE-----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=osgb
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Revert a simplification that broke pci-tegra due to a masking error
- Update MAINTAINERS for Kishon's email address change and TI
DRA7XX/J721E maintainer change
* tag 'pci-v6.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Kishon's email address in PCI endpoint subsystem
MAINTAINERS: Add Vignesh Raghavendra as maintainer of TI DRA7XX/J721E PCI driver
Revert "PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro"
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAmNTCJ8ACgkQCF8+vY7k
4RV/Ag//Ws8bIdedAQsbakBOq9JPOMiqHZnBde5DWn3XqU8aAY9bby70Rf2OTbl7
8mpqzeJY6wFfvesGCJ8L2hprpVqNW1KCrNAxSyaq/8Wau1D77wyEofqPNarNJzqn
oKbH0JWd8hfStJpgmwyxUXjLanDXNx2s4lRm6R1WMWPH6dLeHydx4CtFMbmOn1L8
+jTtLK6631plWw/Kkp1A9z8N1D/9b4iMOgpoQZZLuzL1DouoYWlltz+Kw9HU7rsQ
1/wGmMwTwiV6Zt2UPwB4qudq3UpUMB3tm0KWprkmSx3Xv14Rr1o3zdwALTXib0Ez
wZuzWzWaf9Fjp7CHOfEpm4x3+kU9181iw4ACk34cq7SglMYCdQ2hiwW5b9hhTN2m
tYxv78fXJD2lHyxZQAHNN7XRmiWfMWMA0Z7GwCLVFXJ24Vjzv5AfuD3rJEE6Fv3X
UOjPTNdNt4tpxX8A2Yd7WlfIBBGm2h63MVIYh50R54JCdLLLB8vhtob7pP2Y94pg
FqXxfwc216cArKVsIjmUUkJs153IlQPYzBv9xXBBbD2DXhguWhLQnf9L/KdCnFkF
6NTULAHNezkss6dbLPIL08lCEIvTqeQabPBlCEtXNqqxBWfJwdwLbeS8mg2dTxao
wwR5D37JbNuDSj0/4N/DlvVJozcCLJ2ZZ9R3c2j8/4Z0HERIhqA=
=gJf4
-----END PGP SIGNATURE-----
Merge tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull missed media updates from Mauro Carvalho Chehab:
"It seems I screwed-up my previous pull request: it ends up that only
half of the media patches that were in linux-next got merged in -rc1.
The script which creates the signed tags silently failed due to
5.19->6.0 so it ended generating a tag with incomplete stuff.
So here are the missing parts:
- a DVB core security fix
- lots of fixes and cleanups for atomisp staging driver
- old drivers that are VB1 are being moved to staging to be
deprecated
- several driver updates - mostly for embedded systems, but there are
also some things addressing issues with some PC webcams, in the UVC
video driver"
* tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (163 commits)
media: sun6i-csi: Move csi buffer definition to main header file
media: sun6i-csi: Introduce and use video helper functions
media: sun6i-csi: Add media ops with link notify callback
media: sun6i-csi: Remove controls handler from the driver
media: sun6i-csi: Register the media device after creation
media: sun6i-csi: Pass and store csi device directly in video code
media: sun6i-csi: Tidy up video code
media: sun6i-csi: Tidy up v4l2 code
media: sun6i-csi: Tidy up Kconfig
media: sun6i-csi: Use runtime pm for clocks and reset
media: sun6i-csi: Define and use variant to get module clock rate
media: sun6i-csi: Always set exclusive module clock rate
media: sun6i-csi: Tidy up platform code
media: sun6i-csi: Refactor main driver data structures
media: sun6i-csi: Define and use driver name and (reworked) description
media: cedrus: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-rotate: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-di: Add a Kconfig dependency on RESET_CONTROLLER
media: sun4i-csi: Add a Kconfig dependency on RESET_CONTROLLER
media: sun6i-csi: Add a Kconfig dependency on RESET_CONTROLLER
...
Conor Dooley