As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net
To prepare for making connector creation optional in the driver, pass
the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer
is passed to the callers where required, particularly to the
dw_hdmi_phy_ops .init() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
Current code initializes HDMI PHY clock driver before reset line is
deasserted and clocks enabled. Because of that, initial readout of
clock divider is incorrect (0 instead of 2). This causes any clock
rate with divider 1 (register value 0) to be set incorrectly.
Fix this by moving initialization of HDMI PHY clock driver after reset
line is deasserted and clocks enabled.
Cc: stable@vger.kernel.org # 4.17+
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190514204337.11068-2-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
The A64 HDMI PHY seems to be not able to use the second video PLL as
clock parent in experiments.
Drop the support for the second PLL from A64 HDMI PHY driver.
Fixes: b46e2c9f5f ("drm/sun4i: Add support for A64 HDMI PHY")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180916043409.62374-2-icenowy@aosc.io
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net
While A83T HDMI PHY seems to be just customized Synopsys HDMI PHY, H3
HDMI PHY is completely custom PHY.
However, they still have many things in common like clock and reset
setup, setting sync polarity and more.
Add support for H3 HDMI PHY variant.
While documentation exists for this PHY variant, it doesn't go in great
details. Because of that, almost all settings are copied from BSP linux
4.4. Interestingly, those settings are slightly different to those found
in a older BSP with Linux 3.4. For now, no user visible difference was
found between them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-13-jernej.skrabec@siol.net
There are multiple variants of DW HDMI PHYs in Allwinner SoCs. While
some things like clock and reset setup are the same, PHY configuration
differs a lot.
Split out code which is PHY specific to separate functions and create
a structure which holds pointers to those functions.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-11-jernej.skrabec@siol.net
Current polarity configuration code is cleary wrong since it compares
same flag two times. However, even if flag name is fixed, it won't work
well for resolutions which have one polarity positive and another
negative.
Fix that by properly set each bit according to each polarity. Since
those two bits are not described in any documentation, relationships
were obtained by experimentation.
Fixes: b7c7436a5f ("drm/sun4i: Implement A83T HDMI driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-10-jernej.skrabec@siol.net
A83T has DW HDMI IP block with a custom PHY similar to Synopsys gen2
HDMI PHY.
Only video output was tested, while HW also supports audio and CEC.
Support for them will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-11-jernej.skrabec@siol.net
Jernej Skrabec