Simplify probe function by adding a local variable dev instead of using
&client->dev all the time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ACPI _HID INT347A represents the OV8865 sensor, the driver for which can
support the platforms that the cio2-bridge serves. Add it to the array
of supported sensors so the bridge will connect the sensor to the CIO2
device.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum gain figure in the v4l2 ctrl is wrong. The field is 12 bits
wide, which is where the 8191 figure comes from, but the datasheet is
specific that maximum gain is 16x (the low seven bits are fractional, so
16x gain is 2048)
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a chance that regulator_get() returns -EPROBE_DEFER, in which
case printing an error message is undesirable. To avoid spurious messages
in dmesg in the event that -EPROBE_DEFER is returned, use dev_err_probe()
on error paths for regulator_get().
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control
as 1/16th of a line. This is what the sensor expects, but isn't very
intuitive. Switch the control to be in units of a line and simply do the
16x multiplication before passing the value to the sensor.
The datasheet for this sensor gives minimum exposure as 2 lines, so take
the opportunity to correct the lower bounds of the control.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure limits depend on the total height; when vblank is altered (and
thus the total height is altered), change the exposure limits to reflect
the new cap.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HTS values for some of the modes in the ov8865 driver are a bit
unusual, coming in lower than the output_size_x is set to. It seems
like they might be calculated to fit the desired framerate into a
configuration with just two data lanes. To bring this more in line
with expected behaviour, raise the HTS values above the output_size_x.
The corollary of that change is that the hardcoded frame intervals
against the modes no longer make sense, so remove those entirely.
Update the .g/s_frame_interval() callbacks to calculate the frame
interval based on the current mode and the vblank and hblank settings.
The implementation of the .enum_frame_interval() callback is no longer
suitable since the possible frame rate is now a continuous range depending
on the vblank control setting, so remove that callback entirely.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only
with timing control intended to be done via vblanking alone.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_VBLANK control to the ov8865 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_CID_GAIN control for this driver configures registers that
the datasheet specifies as analogue gain. Switch the control's ID
to V4L2_CID_ANALOGUE_GAIN.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver's v4l2_subdev_pad_ops currently does not include
.get_selection() - add support for that callback.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver as written expects a 24MHz input clock, but the sensor
is sometimes found on x86 platforms with a 19.2MHz input clock supplied.
Add a set of PLL configurations to the driver to support that rate too.
As ACPI doesn't auto-configure the clock rate, check for a clock-frequency
during probe and set that rate if one is found.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver is one of those that can be connected to a CIO2
device by the cio2-bridge code. This means that the absence of an
endpoint for this device is not necessarily fatal, as one might be
built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no
endpoint is found rather than a fatal error.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL configuration defined here sets 72MHz (which is correct), not
80MHz. Correct the comment.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI.
Add an ACPI match table to the driver so that it's probed on those
platforms.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a link frequency to the cio2-bridge table of supported sensors.
This means that the driver can parse supported link frequencies from
firmware in the usual way and validate that it can accommodate them.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5693 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2. The
chip is capable of a single lane configuration, but currently only two
lanes are supported.
Most of the sensor's features are supported, with the main exception
being the lens correction algorithm.
The driver provides all mandatory, optional and recommended V4L2 controls
for maximum compatibility with libcamera.
[mchehab: fixed a coding style warning]
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The .suspend() and .resume() runtime_pm operations for the ipu3-cio2
driver currently do not handle the sensor's stream. Setting .s_stream() on
or off for the sensor subdev means that sensors will pause and resume the
stream at the appropriate time even if their drivers don't implement those
operations.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Current driver supports only SRGGB 10 bit RAW bayer format.
Add the enum_mbus_code implementation to report this format supported.
# v4l2-ctl -d /dev/v4l-subdev3 --list-subdev-mbus-codes
ioctl: VIDIOC_SUBDEV_ENUM_MBUS_CODE (pad=0)
0x300f: MEDIA_BUS_FMT_SRGGB10_1X10
#
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 has not explicitly declared a dependency upon VIDEO_V4L2.
While this dependency has likely always been met by configurations
including it, the device does use V4L2 core, and should depend upon it.
Add VIDEO_V4L2 as a dependency to match other drivers and prevent
failures when compile testing.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by clang (with W=1), the ctrlVal var is never used.
Yet, there are even some loops to estimate it. As this is dead
code, remove it. If ever needed, someone could revert this
patch.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The clock_control value is read but never actually used. Based on
a comment at the code, it has to be reset at the function.
So, drop the variable that stores its value.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The typecasts at the dvb-core generate clang warnings when W=1
is enabled.
Such warning is harmless, but it causes the build to break with
CONFIG_WERROR and W=1 with clang, so do the cast on a way that
it won't produce warnings anymore.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vfe_reg_clr() is not used in camss-vfe-170.c, and can be removed.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those are aliases for another function and not used at the
current implementation. So, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is not used, so, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This isn't used anywhere. So, drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the version warning is given, multiple dev_warn() are
called. Consolidate the ones that could be merged altogether.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clang doesn't like "%hu" on macros:
drivers/media/radio/si470x/radio-si470x-i2c.c:414:4: error: format specifies type 'unsigned short' but the argument has type 'int' [-Werror,-Wformat]
drivers/media/radio/si470x/radio-si470x-i2c.c:417:4: error: format specifies type 'unsigned short' but the argument has type 'int' [-Werror,-Wformat]
Besides that, changeset cbacb5ab0a ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]")
dropped recomendation of using %h.
So, just replace them with "%u".
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Acked-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an error occurs while setting the registers at set_frontend,
it is silently ignored. Yet, the variable status is updated.
Change the logic to return an error if it fails to write values
to the registers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This value is never used at the code. So, drop it.
Solves a W=1 clang warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The offset is not needed, and it is never used, as the pointer
itself is already incremented.
So, drop it, in order to solve a W=1 clang warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vpif_get_default_field() seems to be some left-over from a
past code that sets the field order.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is just an alias for container_of() and it is used only
on a commented code. The commented code actually is an issue that
require fixes, so, move the container_of() call to the commented
code, and drop the unused function.
This way, a fix for the function could be added later without
needing to re-add to_state() function.
This fixes a clang W=1 warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those functions just call a V4L2 core macro, and aren't used
anywhere. Get rid of them, in order to avoid clang warnings with
W=1.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clang with W=1 produces the following warnings:
drivers/media/platform/omap3isp/isph3a_af.c:173:6: error: result of comparison of constant 256 with expression of type '__u8' (aka 'unsigned char') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (IS_OUT_OF_BOUNDS(paxel_cfg->height, OMAP3ISP_AF_PAXEL_HEIGHT_MIN,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:24:33: note: expanded from macro 'IS_OUT_OF_BOUNDS'
(((value) < (min)) || ((value) > (max)))
~~~~~~~ ^ ~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:179:6: error: result of comparison of constant 256 with expression of type '__u8' (aka 'unsigned char') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (IS_OUT_OF_BOUNDS(paxel_cfg->width, OMAP3ISP_AF_PAXEL_WIDTH_MIN,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:24:33: note: expanded from macro 'IS_OUT_OF_BOUNDS'
(((value) < (min)) || ((value) > (max)))
~~~~~~~ ^ ~~~~~
2 errors generated.
Use a typecast to avoid such warnings.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is only used for debugging purposes. When DEBUG
is disabled, it becomes unused, causing a clang warning with W=1.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is an alias for container_of() that it is currently
not used, causing clang warnings. So, drop it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev