The LEGO-wiimote uses a different VID than the Nintendo ID. The device is
technically the same so add the ID.
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Revert some changes done in 7746383868.
Revert all changes done in hidinput_calc_abs_res as it mistakingly used
"Unit" item exponent nibbles to affect resolution value. This wasn't
breaking resolution calculation of relevant axes of any existing
devices, though, as they have only one dimension to their units and thus
1 in the corresponding nible.
Revert to reading "Unit Exponent" item value as a signed integer in
hid_parser_global to fix reading specification-complying values. This
fixes resolution calculation of devices complying to the HID standard,
including Huion, KYE, Waltop and UC-Logic graphics tablets which have
their report descriptors fixed by the drivers.
Explanations follow.
There are two "unit exponents" in HID specification and it is important
not to mix them. One is the global "Unit Exponent" item and another is
nibble values in the global "Unit" item. See 6.2.2.7 Global Items.
The "Unit Exponent" value is just a signed integer and is used to scale
the integer resolution unit values, so fractions can be expressed.
The nibbles of "Unit" value are used to select the unit system (nibble
0), and presence of a particular basic unit type in the unit formula and
its *exponent* (or power, nibbles 1-6). And yes, the latter is in two
complement and zero means absence of the unit type.
Taking the representation example of (integer) joules from the
specification:
[mass(grams)][length(centimeters)^2][time(seconds)^-2] * 10^-7
the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the
"Unit" value would be 0xE121, signifying:
Nibble Part Value Meaning
----- ---- ----- -------
0 System 1 SI Linear
1 Length 2 Centimeters^2
2 Mass 1 Grams
3 Time -2 Seconds^-2
To give the resolution in e.g. hundredth of joules the "Unit Exponent"
item value should have been -9.
See also the examples of "Unit" values for some common units in the same
chapter.
However, there is a common misunderstanding about the "Unit Exponent"
value encoding, where it is assumed to be stored the same as nibbles in
"Unit" item. This is most likely due to the specification being a bit
vague and overloading the term "unit exponent". This also was and still
is proliferated by the official "HID Descriptor Tool", which makes this
mistake and stores "Unit Exponent" as such. This format is also
mentioned in books such as "USB Complete" and in Microsoft's hardware
design guides.
As a result many devices currently on the market use this encoding and
so the driver should support them.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Minor correction to the description in Kconfig.
The Logitect MOMO wheel is actually handled by the LOGITECH_WHEELS (hid-lg4ff)
section, not by the LOGITECH_FF (hid-lgff).
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default the Logitech MOMO Force (Black) presents a combined accel/brake
axis ('Y'). This patch modifies the HID descriptor to present seperate
accel/brake axes ('Y' and 'Z').
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default the Logitech Formula Vibration presents a combined accel/brake
axis ('Y'). This patch modifies the HID descriptor to present seperate
accel/brake axes ('Y' and 'Z').
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use case: people who use both Apple and PC keyboards regularly, and desire to
keep&use their PC muscle memory.
A particular use case: an Apple compact external keyboard connected to a PC
laptop. (This use case can't be covered well by X.org key remappings etc.)
Signed-off-by: Nanno Langstraat <langstr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
[12431.828467] hid-multitouch 0003:0457:1013.0475: usb_submit_urb(ctrl) failed: -1
[12431.828507] hid-multitouch 0003:0457:1013.0475: timeout initializing reports
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
Synaptics large touchscreen doesn't support some of the report request
while initializing. The unspoorted request will make the device unreachable,
and will lead to the following usb_submit_urb() function call timeout.
So, add the IDs into HID_QUIRK_NO_INIT_REPORTS quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add USB IDs for Logitech Formula Vibration Feedback Wheel (046d:ca04).
The lg2ff force feedback subdriver is used for vibration and
HID_GD_MULTIAXIS is set to avoid deadzone like other Logitech wheels.
Kconfig description etc are also updated accordingly.
Signed-off-by: Elias Vanderstuyft <Elias.vds@gmail.com>
[anssi.hannula@iki.fi: added description and CCs]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GeneralTouch products should use the quirk SLOT_IS_CONTACTID
instead of SLOT_IS_CONTACTNUMBER.
Adding PIDs 0101,e100,0102,0106,010a from the new products.
Tested on new and older products by GeneralTouch engineers.
Signed-off-by: Luosong <android@generaltouch.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The input core has an internal spinlock that is acquired during event
injection via input_event() and friends but also held during FF callbacks.
That means, there is no way to share a lock between event-injection and FF
handling. Unfortunately, this is what is required for wiimote state
tracking and what we do with state.lock and input->lock.
This deadlock can be triggered when using continuous data reporting and FF
on a wiimote device at the same time. I takes me at least 30m of
stress-testing to trigger it but users reported considerably shorter
times (http://bpaste.net/show/132504/) when using some gaming-console
emulators.
The real problem is that we have two copies of internal state, one in the
wiimote objects and the other in the input device. As the input-lock is
not supposed to be accessed from outside of input-core, we have no other
chance than offloading FF handling into a worker. This actually works
pretty nice and also allows to implictly merge fast rumble changes into a
single request.
Due to the 3-layered workers (rumble+queue+l2cap) this might reduce FF
responsiveness. Initial tests were fine so lets fix the race first and if
it turns out to be too slow we can always handle FF out-of-band and skip
the queue-worker.
Cc: <stable@vger.kernel.org> # 3.11+
Reported-by: Thomas Schneider
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added id, bindings and comments for Holtek USB ID 04d9:a081 SHARKOON
DarkGlider Gaming mouse to use the same corrections of the report
descriptor as Holtek 04d9:a04a. As the mouse exceed HID_MAX_USAGES
at the same offsets in the reported descriptor.
Tested on the hardware.
Signed-off-by: Anders F. U. Kiær <ablacksheep@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though device exist bit is set the underlying
HW device should be closed when the last reader
of the device is closed i.e. open count drops to zero.
Signed-off-by: Manoj Chourasia <mchourasia@nvidia.com>
Reported-by: mika.westerberg@linux.intel.com
Tested-by: mika.westerberg@linux.intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't call hid_open_device till there is actually an user. This saves
power by not opening underlying transport for HID. Also close device
if there are no active mfd client using HID sensor hub.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
udev has this nice feature of creating "dead" /dev/<node> device-nodes if
it finds a devnode:<node> modalias. Once the node is accessed, the kernel
automatically loads the module that provides the node. However, this
requires udev to know the major:minor code to use for the node. This
feature was introduced by:
commit 578454ff7e
Author: Kay Sievers <kay.sievers@vrfy.org>
Date: Thu May 20 18:07:20 2010 +0200
driver core: add devname module aliases to allow module on-demand auto-loading
However, uhid uses dynamic minor numbers so this doesn't actually work. We
need to load uhid to know which minor it's going to use.
Hence, allocate a static minor (just like uinput does) and we're good
to go.
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some systems although they have firmware class 'M', which usually
needs a work around to not crash, must not be subjected to the
work around because the work around crashes them. They cannot be
told apart by their own device descriptor, but as they are part
of compound devices, can be identified by looking at their siblings.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usb packets are exactly the same, but it makes it a little bit more
independent of the transport layer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
lenovo tpkbd currently relies on the usb interface number to detect
if it is dealing with the touchpad interface or not.
As the report descriptors of the interface 0 does not contain the
button 3, we can use this to remove the need to check for usb.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can use the devres API in hid modules, so use it to avoid some kfree
and potential leaks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
acpi_evaluate_integer() is an ACPI API introduced to evaluate an
ACPI control method that is known to have an integer return value.
This API can simplify the code because the calling function does not need to
use the specified acpi_buffer structure required by acpi_evaluate_object();
Convert acpi_evaluate_object() to acpi_evaluate_integer()
in drivers/hid/i2c-hid/i2c-hid.c in this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If tpkbd_probe_tp() bails out, the probe() function return an error,
but hid_hw_stop() is never called.
fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1003998
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When working on report indexes, always validate that they are in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
Note that we need to change the indexes from s8 to s16 as they can
be between -1 and 255.
CVE-2013-2897
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
logitech-dj HID driver to leak kernel memory contents to the device, or
trigger a NULL dereference during initialization:
[ 304.424553] usb 1-1: New USB device found, idVendor=046d, idProduct=c52b
...
[ 304.780467] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
[ 304.781409] IP: [<ffffffff815d50aa>] logi_dj_recv_send_report.isra.11+0x1a/0x90
CVE-2013-2895
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When dealing with usage_index, be sure to properly use unsigned instead of
int to avoid overflows.
When working on report fields, always validate that their report_counts are
in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2897
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
lenovo-tpkbd HID driver to write just beyond the output report allocation
during initialization, causing a heap overflow:
[ 76.109807] usb 1-1: New USB device found, idVendor=17ef, idProduct=6009
...
[ 80.462540] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2894
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
lg, lg3, and lg4 HID drivers to write beyond the output report allocation
during an event, causing a heap overflow:
[ 325.245240] usb 1-1: New USB device found, idVendor=046d, idProduct=c287
...
[ 414.518960] BUG kmalloc-4096 (Not tainted): Redzone overwritten
Additionally, while lg2 did correctly validate the report details, it was
cleaned up and shortened.
CVE-2013-2893
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
steelseries HID driver to write beyond the output report allocation
during initialization, causing a heap overflow:
[ 167.981534] usb 1-1: New USB device found, idVendor=1038, idProduct=1410
...
[ 182.050547] BUG kmalloc-256 (Tainted: G W ): Redzone overwritten
CVE-2013-2891
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver must validate the availability of the HID output report and
its size before it can write LED states via buzz_set_leds(). This stops
a heap overflow that is possible if a device provides a malicious HID
output report:
[ 108.171280] usb 1-1: New USB device found, idVendor=054c, idProduct=0002
...
[ 117.507877] BUG kmalloc-192 (Not tainted): Redzone overwritten
CVE-2013-2890
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org #3.11
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The zeroplus HID driver was not checking the size of allocated values
in fields it used. A HID device could send a malicious output report
that would cause the driver to write beyond the output report allocation
during initialization, causing a heap overflow:
[ 1442.728680] usb 1-1: New USB device found, idVendor=0c12, idProduct=0005
...
[ 1466.243173] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2889
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many drivers need to validate the characteristics of their HID report
during initialization to avoid misusing the reports. This adds a common
helper to perform validation of the report exisitng, the field existing,
and the expected number of values within the field.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This reverts commits 61e00655e9, 73f8645db1 and 8e22ecb603c8:
"Input: introduce BTN/ABS bits for drums and guitars"
"HID: wiimote: add support for Guitar-Hero drums"
"HID: wiimote: add support for Guitar-Hero guitars"
The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic. It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.
We'll try again for 3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID updates from Jiri Kosina:
"Highlights:
- conversion of HID subsystem to use devm-based resource management,
from Benjamin Tissoires
- i2c-hid support for DT bindings, from Benjamin Tissoires
- much improved support for Win8-multitouch devices, from Benjamin
Tissoires
- cleanup of core code using common hidinput_input_event(), from
David Herrmann
- fix for bug in implement() access to the bit stream (causing oops)
that has been present in the code for ages, but devices that are
able to trigger it have started to appear only now, from Jiri
Kosina
- fixes for CVE-2013-2899, CVE-2013-2898, CVE-2013-2896,
CVE-2013-2892, CVE-2013-2888 (all triggerable only by specially
crafted malicious HW devices plugged into the system), from Kees
Cook
- hidraw oops fix, from Manoj Chourasia
- various smaller fixes here and there, support for a bunch of new
devices by various contributors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (53 commits)
HID: MAINTAINERS: add roccat drivers
HID: hid-sensor-hub: change kmalloc + memcpy by kmemdup
HID: hid-sensor-hub: move to devm_kzalloc
HID: hid-sensor-hub: fix indentation accross the code
HID: move HID_REPORT_TYPES closer to the report-definitions
HID: check for NULL field when setting values
HID: picolcd_core: validate output report details
HID: sensor-hub: validate feature report details
HID: ntrig: validate feature report details
HID: pantherlord: validate output report details
HID: hid-wiimote: print small buffers via %*phC
HID: uhid: improve uhid example client
HID: Correct the USB IDs for the new Macbook Air 6
HID: wiimote: add support for Guitar-Hero guitars
HID: wiimote: add support for Guitar-Hero drums
Input: introduce BTN/ABS bits for drums and guitars
HID: battery: don't do DMA from stack
HID: roccat: add support for KonePureOptical v2
HID: picolcd: Prevent NULL pointer dereference on _remove()
HID: usbhid: quirk for N-Trig DuoSense Touch Screen
...
The patch substitutes kmemdup for kmalloc followed by memcpy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
devm_kzalloc() will manage resources freeing and allows to make error path
smaller and nicer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch just rearranges lines to be more compact and/or readable. Additionally it
converts double space to one in several places.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This one didn't make it for 3.11 due to being applied too close
to release, queue it for 3.12 merge window.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defensively check that the field to be worked on is not NULL.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
picolcd HID driver to trigger a NULL dereference during attr file writing.
[jkosina@suse.cz: changed
report->maxfield < 1
to
report->maxfield != 1
as suggested by Bruno].
CVE-2013-2899
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Reviewed-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious feature report that would cause the
sensor-hub HID driver to read past the end of heap allocation, leaking
kernel memory contents to the caller.
CVE-2013-2898
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious feature report that would cause the
ntrig HID driver to trigger a NULL dereference during initialization:
[57383.031190] usb 3-1: New USB device found, idVendor=1b96, idProduct=0001
...
[57383.315193] BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
[57383.315308] IP: [<ffffffffa08102de>] ntrig_probe+0x25e/0x420 [hid_ntrig]
CVE-2013-2896
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A HID device could send a malicious output report that would cause the
pantherlord HID driver to write beyond the output report allocation
during initialization, causing a heap overflow:
[ 310.939483] usb 1-1: New USB device found, idVendor=0e8f, idProduct=0003
...
[ 315.980774] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
CVE-2013-2892
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of passing each byte through stack let's use %*phC specifier to dump
buffer as a hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent patch (9d9a04ee) added support for the new machine, but got
the sequence of USB ids wrong. Reports from both Ian and Linus T show
that the 0x0291 id is for ISO, not ANSI, which should have the missing
number 0x0290. This patchs moves the three numbers accordingly, fixing
the problem.
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Tested-by: Linus G Thiel <linus@hanssonlarsson.se>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sync with Linus' tree to be able to apply fixup patch on top
of 9d9a04ee75 ("HID: apple: Add support for the 2013 Macbook Air")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Apart from drums, Guitar-Hero also ships with guitars. Use the recently
introduced input ABS/BTN-bits to report this to user-space.
Devices are reported as "Nintendo Wii Remote Guitar". If I ever get my
hands on "RockBand" guitars, I will try to report them via the same
interface so user-space does not have to bother which device it deals
with.
Signed-off-by: Nicolas.Adenis-Lamarre <nicolas.adenis.lamarre@gmail.com>
(add commit-msg and adjust to new BTN_* IDs)
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Guitar-Hero comes with a drums extension. Use the newly introduced input
drums-bits to report this back to user-space. This is a usual extension
like any other device. Nothing special to take care of.
We report this to user-space as "Nintendo Wii Remote Drums". There are
other drums (like "RockBand" drums) which we currently do not support and
maybe will at some point. However, it is quite likely that we can report
these via the same interface. This allows user-space to work with them
without knowing the exact branding.
I couldn't find anyone who owns a "RockBand" device, though.
Initial-work-by: Nicolas Adenis-Lamarre <nicolas.adenis.lamarre@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Instead of using data from stack for DMA in hidinput_get_battery_property(),
allocate the buffer dynamically.
Cc: stable@kernel.org
Reported-by: Richard Ryniker <ryniker@alum.mit.edu>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
KonePureOptical is a KonePure with different sensor.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DuoSense touchscreen device causes a 10 second timeout. This fix
removes the delay.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The "Report ID" field of a HID report is used to build indexes of
reports. The kernel's index of these is limited to 256 entries, so any
malicious device that sets a Report ID greater than 255 will trigger
memory corruption on the host:
[ 1347.156239] BUG: unable to handle kernel paging request at ffff88094958a878
[ 1347.156261] IP: [<ffffffff813e4da0>] hid_register_report+0x2a/0x8b
CVE-2013-2888
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some multitouch screens do not like to be polled for input reports.
However, the Win8 spec says that all touches should be sent during
each report, making the initialization of reports unnecessary.
The Win7 spec is less precise, so do not use this for those devices.
Add the quirk HID_QUIRK_NO_INIT_INPUT_REPORTS so that we do not have to
introduce a quirk for each problematic device. This quirk makes the driver
behave the same way the Win 8 does. It actually retrieves the features,
but not the inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Detecting Win 8 multitouch devices in core allows us to set quirks
before the device is parsed through hid_hw_start().
It also simplifies the detection of those devices in hid-multitouch and
makes the handling of those devices cleaner.
As Win 8 multitouch panels are in the group multitouch and rely on a
special feature to be detected, this patch adds a bitfield in the parser.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Win 8 detection is sufficiently complex to warrant use of the full
parser code, in spite of the inferred memory usage. Therefore, we can use
the existing HID parser in hid-core for hid_scan_report() by re-using the
code from hid_open_report(). hid_parser_global, hid_parser_local and
hid_parser_reserved does not have any side effects. We just need to
reimplement the MAIN_ITEM callback to have a proper parsing without side
effects.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is unsafe to call list_for_each_entry in hidraw_report_event to
traverse each hidraw_list node without a lock protection, the list
could be modified if someone calls hidraw_release and list_del to
remove itself from the list, this can cause hidraw_report_event
to touch a deleted list struct and panic.
To prevent this, introduce a spinlock in struct hidraw to protect
list from concurrent access.
Signed-off-by: Yonghua Zheng <younghua.zheng@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the HID bus code to use
the correct field.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices of the "Speedlink VAD Cezanne" model need more aggressive fixing
than already done.
I made sure through testing that this patch would not interfere with the proper
working of a device that is bug-free. (The driver drops EV_REL events with
abs(val) >= 256, which are not achievable even on the highest laser resolution
hardware setting.)
Signed-off-by: Stefan Kriwanek <mail@stefankriwanek.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes the style of the comments to be like following
/* The commentary */
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI 5.0 specification requires the fourth parameter to the _DSM (Device
Specific Method) to be of type package instead of integer. Failing to do
that we get following warning on the console:
ACPI Warning: \_SB_.PCI0.I2C1.TPL0._DSM: Argument #4 type mismatch - Found [Integer],
ACPI requires [Package] (20130517/nsarguments-95)
Fix this by passing an empty package to the _DSM method. The HID over I2C
specification doesn't require any specific values to be passed with this
parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stefan pointed out that I messed up the array for the binary attributes,
so fix it properly.
Reported-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that attribute groups support binary attributes, use them instead of
the dev_bin_attrs field in struct class, as that is going away soon.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the roccat class code to use the
correct field.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 407a2c2a4d.
Explanation provided by Benjamin Tissoires:
Commit "HID: hid-logitech-dj, querying_devices was never set" activate
a flag which guarantees that we do not ask the receiver for too many
enumeration. When the flag is set, each following enumeration call is
discarded (the usb request is not forwarded to the receiver). The flag
is then released when the driver receive a pairing information event,
which normally follows the enumeration request.
However, the USB3 bug makes the driver think the enumeration request
has been forwarded to the receiver. However, it is actually not the
case because the USB stack returns -EPIPE. So, when a new unknown
device appears, the workaround consisting in asking for a new
enumeration is not working anymore: this new enumeration is discarded
because of the flag, which is never reset.
A solution could be to trigger a timeout before releasing it, but for
now, let's just revert the patch.
Reported-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Tested-by: Sune Mølgaard <sune@molgaard.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This changes puts the commit 4fe9f8e203 back in place
with the fixes for slab corruption because of the commit.
When a device is unplugged, wait for all processes that
have opened the device to close before deallocating the device.
This commit was solving kernel crash because of the corruption in
rb tree of vmalloc. The rootcause was the device data pointer was
geting excessed after the memory associated with hidraw was freed.
The commit 4fe9f8e203 was buggy as it was also freeing the hidraw
first and then calling delete operation on the list associated with
that hidraw leading to slab corruption.
Signed-off-by: Manoj Chourasia <mchourasia@nvidia.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GEN10 and earlier devices seem to not support DRM_KAI if we run in basic
IR mode. Use DRM_KAIE instead. This might increases overhead slightly as
the extension port is read and streamed but we stream accelerometer data
constantly, too, so this is negligible.
Note that our parsers are hardcoded on IR-formats, so we cannot actually
use 96-bit IR DRMs for basic IR data. We would have to adjust the parsers.
But as only GEN20 and newer support this, we simply avoid mixed DRMs.
This fixes a bug where GEN10 devices didn't provide IR data if
accelerometer and IR are enabled simultaneously. As a workaround, you can
enable DRM_KAIE without this patch via (disables device power-management):
echo "37" >/sys/kernel/debug/hid/<dev>/drm
Cc: stable@vger.kernel.org
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reported-by: Nicolas Adenis-Lamarre <nicolas.adenis.lamarre@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove HV_DRV_VERSION, it has no meaning for upstream drivers.
Initially it was supposed to show the "Linux Integration Services"
version, now it is not in sync anymore with the out-of-tree drivers
available from the MSFT website.
The only place where a version string is still required is the KVP
command "IntegrationServicesVersion" which is handled by
tools/hv/hv_kvp_daemon.c. To satisfy such KVP request from the host pass
the current string to the daemon during KVP userland registration.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mutex can not be released unless all hid_device members are properly
initialized. Otherwise it would result in a race condition that can
cause NULL pointer kernel panic issue in hidraw_open where it uses
uninitialized 'list' member in list_add_tail().
Signed-off-by: Yonghua Zheng <younghua.zheng@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add device tree based support for HID over I2C devices.
Tested on an Odroid-X board with a Synaptics touchpad.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hidinput_input_event() callback converts input events written from
userspace into HID reports and sends them to the device. We currently
implement this in every HID transport driver, even though most of them do
the same.
This provides a generic hidinput_input_event() implementation which is
mostly copied from usbhid. It uses a delayed worker to allow multiple LED
events to be collected into a single output event.
We use the custom ->request() transport driver callback to allow drivers
to adjust the outgoing report and handle the request asynchronously. If no
custom ->request() callback is available, we fall back to the generic raw
output report handler (which is synchronous).
Drivers can still provide custom hidinput_input_event() handlers (see
logitech-dj) if the generic implementation doesn't fit their needs.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core provides the same functionality and can convert the input event
to a raw output report. We can thus drop UHID_OUTPUT_EV and rely on the
mandatory UHID_OUTPUT.
User-space wasn't able to do anything with UHID_OUTPUT_EV, anyway. They
don't have access to the report fields.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core provides the same functionality, so drop the custom handler.
Besides, the current handler doesn't schedule any outgoing report so it
did not work, anyway.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core provides the same functionality as we do, so drop the custom
hidinput_input_event() handler.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report fields can be updated from HID drivers unlocked via
hid_set_field(). It is protected by input_lock in HID core so only a
single input event is handled at a time. USBHID can thus update the field
unlocked and doesn't conflict with any HID vendor/device drivers. Note,
many HID drivers make heavy use of hid_set_field() in that way.
But usbhid also schedules a work to gather multiple LED changes in a
single report. Hence, we used to lock the LED field update so the work can
read a consistent state. However, hid_set_field() only writes a single
integer field, which is guaranteed to be allocated all the time. So the
worst possible race-condition is a garbage read on the LED field.
Therefore, there is no need to protect the update. In fact, the only thing
that is prevented by locking hid_set_field(), is an LED update while the
scheduled work currently writes an older LED update out. However, this
means, a new work is scheduled directly when the old one is done writing
the new state to the device. So we actually _win_ by not protecting the
write and allowing the write to be combined with the current write. A new
worker is still scheduled, but will not write any new state. So the LED
will not blink unnecessarily on the device.
Assume we have the LED set to 0. Two request come in which enable the LED
and immediately disable it. The current situation with two CPUs would be:
usb_hidinput_input_event() | hid_led()
---------------------------------+----------------------------------
spin_lock(&usbhid->lock);
hid_set_field(1);
spin_unlock(&usbhid->lock);
schedule_work(...);
spin_lock(&usbhid->lock);
__usbhid_submit_report(..1..);
spin_unlock(&usbhid->lock);
spin_lock(&usbhid->lock);
hid_set_field(0);
spin_unlock(&usbhid->lock);
schedule_work(...);
spin_lock(&usbhid->lock);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
With the locking removed, we _might_ end up with (look at the changed
__usbhid_submit_report() parameters in the first try!):
usb_hidinput_input_event() | hid_led()
---------------------------------+----------------------------------
hid_set_field(1);
schedule_work(...);
spin_lock(&usbhid->lock);
hid_set_field(0);
schedule_work(...);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
... next work ...
spin_lock(&usbhid->lock);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
As one can see, we no longer send the "LED ON" signal as it is disabled
immediately afterwards and the following "LED OFF" request overwrites the
pending "LED ON".
It is important to note that hid_set_field() is not atomic, so we might
also end up with any other value. But that doesn't matter either as we
_always_ schedule the next work with a correct value and schedule_work()
acts as memory barrier, anyways. So in the worst case, we run
__usbhid_submit_report(..<garbage>..) in the first case and the following
__usbhid_submit_report() will write the correct value. But LED states are
booleans so any garbage will be converted to either 0 or 1 and the remote
device will never see invalid requests.
Why all this? It avoids any custom locking around hid_set_field() in
usbhid and finally allows us to provide a generic hidinput_input_event()
handler for all HID transport drivers.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usbhid_set_leds() is only used inside of usbhid/hid-core.c so no need to
export it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID special drivers can use safely the devres API.
Use it to remove 25 lines of code and to clean up a little the error paths.
Besides the basic kzalloc -> devm_kzalloc conversions, I changed the
place of the allocation of the new name. Doing this right in
mt_input_configured() removes the kstrdup call which was not very helpful
and the new way is simpler to understand (and to debug).
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is safe to use devres allocation within the hid subsystem:
- the devres release is called _after_ the call to .remove(), meaning
that no freed pointers will exists while removing the device
- if a .probe() fails, devres releases all the allocated ressources
before going to the next driver: there will not be ghost ressources
attached to a hid device if several drivers are probed.
Given that, we can clean up a little some of the HID drivers. These ones
are trivial:
- there is only one kzalloc in the driver
- the .remove() callback contains only one kfree on top of hid_hw_stop()
- the error path in the probe is easy enough to be manually checked
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver currently only supports the Dual Arcade controller.
It fixes the negative axis event values (the devices sends -2) to match the
logical axis minimum of the HID report descriptor (the report announces -1).
It is needed because hid-input discards out of bounds values.
Signed-off-by: Olivier Scherler <oscherler@ithink.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit f04d51404f (HID: driver for PS2/3 Buzz controllers) introduced
an input_mapping() callback, but set the return value to -1 to all devices
except the Buzz controllers. The result of this is that the Sixaxis input
device is not populated, making it useless.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set querying_devices flag to true when we start the enumeration
process.
This was missing from the original patch. It never produced
undesirable effects as it is highly improbable to have a second
enumeration triggered while a first one was still in progress.
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 8af6c08830.
This patch re-adds the workaround introduced by 596264082f
which was reverted by 8af6c08830.
The original patch 596264 was needed to overcome a situation where
the hid-core would drop incoming reports while probe() was being
executed.
This issue was solved by c849a6143b which added
hid_device_io_start() and hid_device_io_stop() that enable a specific
hid driver to opt-in for input reports while its probe() is being
executed.
Commit a9dd22b730 modified hid-logitech-dj so as to use the
functionality added to hid-core. Having done that, workaround 596264
was no longer necessary and was reverted by 8af6c08.
We now encounter a different problem that ends up 'again' thwarting
the Unifying receiver enumeration. The problem is time and usb controller
dependent. Ocasionally the reports sent to the usb receiver to start
the paired devices enumeration fail with -EPIPE and the receiver never
gets to enumerate the paired devices.
With dcd9006b1b the problem was "hidden" as the call to the usb
driver became asynchronous and none was catching the error from the
failing URB.
As the root cause for this failing SET_REPORT is not understood yet,
-possibly a race on the usb controller drivers or a problem with the
Unifying receiver- reintroducing this workaround solves the problem.
Overall what this workaround does is: If an input report from an
unknown device is received, then a (re)enumeration is performed.
related bug:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1194649
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
implement() is setting bytes in LE data stream. In case the data is not
aligned to 64bits, it reads past the allocated buffer. It doesn't really
change any value there (it's properly bitmasked), but in case that this
read past the boundary hits a page boundary, pagefault happens when
accessing 64bits of 'x' in implement(), and kernel oopses.
This happens much more often when numbered reports are in use, as the
initial 8bit skip in the buffer makes the whole process work on values
which are not aligned to 64bits.
This problem dates back to attempts in 2005 and 2006 to make implement()
and extract() as generic as possible, and even back then the problem
was realized by Adam Kroperlin, but falsely assumed to be impossible
to cause any harm:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html
I have made several attempts at fixing it "on the spot" directly in
implement(), but the results were horrible; the special casing for processing
last 64bit chunk and switching to different math makes it unreadable mess.
I therefore took a path to allocate a few bytes more which will never make
it into final report, but are there as a cushion for all the 64bit math
operations happening in implement() and extract().
All callers of hid_output_report() are converted at the same time to allocate
the buffer by newly introduced hid_alloc_report_buf() helper.
Bruno noticed that the whole raw_size test can be dropped as well, as
hid_alloc_report_buf() makes sure that the buffer is always of a proper
size.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius Gx Imperator Keyboard presents the same problem in its report
descriptors than Genius Gila Gaming Mouse.
Use the same fixup for both.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=928561
Reported-and-tested-by: Honza Brazdil <jbrazdil@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When device with the DELIMITER tag in its report descriptor is encountered
during parsing, it's mistakenly immediately refused by HID core for no
justifiable reason.
[jkosina@suse.cz: polish changelog]
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the inlined helpers hid_hw_open/close instead of direct calls to
->ll_driver->open() and ->ll_driver->close().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input updates from Dmitry Torokhov:
"First round of updates for the input subsystem.
You will get a new touchsreen driver for Cypress 4th generation
devices, a driver for a special controller implementing PS/2 protocol
in OLPC devices, and a driver for power key for SiRFprimaII PWRC.
HID and bcm5497 now support for the 2013 MacBook Air.
EVIOCGKEY and the rest of evdev ioctls now flush events of matching
type from the client's event queue so that clients can be sure any
events received after issuing EVIOCG* ioctl are new events.
And a host of cleanups and improvements in other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: cyttsp4 - kfree xfer_buf on error path in probe()
Input: tps6507x-ts - select INPUT_POLLDEV
Input: bcm5974 - add support for the 2013 MacBook Air
HID: apple: Add support for the 2013 Macbook Air
Input: cyttsp4 - leak on error path in probe()
Input: cyttsp4 - silence NULL dereference warning
Input: cyttsp4 - silence shift wrap warning
Input: tps6507x-ts - convert to polled input device infrastructure
ARM: davinci: da850-evm: remove vref from touchscreen platform data
Input: cyttsp4 - SPI driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - I2C driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices
Input: cyttsp - I2C driver split into two modules
Input: add OLPC AP-SP driver
Input: nspire-keypad - remove redundant dev_err call in nspire_keypad_probe()
Input: tps6507x-ts - remove vref from platform data
Input: tps6507x-ts - use bool for booleans
Input: tps6507x-ts - remove bogus unreachable code
Input: samsung-keypad - let device core setup the default pin configuration
Input: wacom_i2c - implement hovering capability
...
Intuos4 WL is separately reporting power supply and battery
charging status - now hid-wacom is using that information.
Previously hid-wacom was wrongly treating "battery charging" bit
as "power supply connected". Now it should report battery charging,
battery discharging, battery full and power supply status.
Intuos4 WL sends reports when is in use (obvious) and when unplugging
power supply. If means that if the device is being charged, but it's not
being used it will never report "battery full". The same problem happens
after the device has been connected, but it's not in use - the
battery/ac status will be incorrect. Currently there is no mechanism to
ask the device to send a report containing battery/ac status.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current i2c hid driver does not support sending HID output reports using
the output register for devices which support receiving reports through this
method. This patch determines which method to use to send output reports based
on the value of wMaxOutputLength in the device's HID descriptor.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds keyboard support for MacbookAir6,2 as WELLSPRING8
(0x0291, 0x0292, 0x0293). The touchpad is handled in a separate
bcm5974 patch, as usual.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Wii U Pro Controller is a new Nintendo remote device that looks very
similar to the XBox controller. It has nearly the same features and uses
the same protocol as the Wii Remote.
We add a new wiimote extension device so the Pro Controller is properly
detected and supported.
The device reports MP support, which is odd and I couldn't get it working,
yet. Hence, we disable MP registers for now. Further investigation is
needed to see what extra capabilities are provided.
There are some other unknown bits in the extension reports that I couldn't
figure out what they do. You can use hidraw to access these if you're
interested.
We might want to hook up the "charging" and "USB" bits to the battery
device so user-space can query whether it is currently charged via USB.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Extend the comment explaining the condition for discarding
out-of-range values to clarify the cases in which devices don't
provide any logical min/max.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 6da7066906 introduced in 3.3
"HID: ignore absolute values which don't fit between logical min and max"
prevents some Posiflex touch screen to work because they do not provide
logical min and max for their buttons.
Thus, logical min and max are at 0, discarding the buttons events, and
preventing the device to report appropriate X Y.
Adding a check on "min < max" solves the problem.
Reported-by: Jan Kandziora <jjj@gmx.de>
Tested-by: Jan Kandziora <jjj@gmx.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Return value of cdev_add in hid_roccat.c init was not checked.
Signed-off-by: Michael Rissi <michael.rissi@dectris.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Let's follow the structure we are trying to keep for most of the
specific HID drivers, and let the separation follow the producing
vendor.
Merge functionality provided by ps3remote driver into hid-sony.
Tested-by: David Dillow <dave@thedillows.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
mt_free_input_name() was never called during .remove():
hid_hw_stop() removes the hid_input items in hdev->inputs, and so the
list is therefore empty after the call. In the end, we never free the
special names that has been allocated during .probe().
Restore the original name before freeing it to avoid acessing already
freed pointer.
This fixes a regression introduced by 49a5a827a ("HID: multitouch: append " Pen" to
the name of the stylus input")
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hdrw->raw event can return three different return value types:
- ret < 0 indicates that the hdrv driver found an error while parsing
- ret == 0 indicates no error has been encountered, and the driver has
processed the report
- ret > 0 indicates that there was no parsing error, and the driver hasn't
processed the event.
Calling hid_report_raw_event() has to be called appropriately so that it
reflects what has been done by ->raw_event() callback, otherwise we might
updates of the in-kernel structure are lost upon arrival of the report, which
is wrong.
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reported-and-tested-by: Daniel Leung <daniel.leung@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an extension device isn't initialized properly, or during hardware
initialization, a device might send extension data which is all 0xff.
This is ambigious because this is also a valid normal data report. But
it is impossible, under normal conditions, to trigger valid reports with
all 0xff. Hence, we can safely ignore them.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I finally got a "Classic Controller" and "Classic Controller Pro" in my
hands and noticed that all analog data was incorrectly parsed. Fix this
up so we report the data that we pretend we do.
I really doubt that this breaks any backwards compatibility, but if we
get any reports, we only need to revert this single patch.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We normally get EXT hotplug events or poll for MP hotplugging so we
don't need to force extension port initialization during device setup.
But for gen20 devices, we disable MP polling because MP is always
present. However, this prevents MP initialization during device setup
and users need to plug another extension to trigger EXT/MP detection.
Therefore, we now trigger EXT/MP detection during device setup
automatically. This also avoids slightly delayed extension detection
and provides sysfs child-devices prior to the "changed"-uevent during
device setup.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to correctly zero-terminate the input to parse it. Otherwise, we
always end up interpreting it as numbers.
Furthermore, we actually want hexadecimal numbers instead of decimal. As
it is a debugfs interface, we can change the API at any time.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices which have built-in motion plus ports don't need MP detection
logic. The new WIIMOD_BUILTIN_MP modules sets the WIIPROTO_FLAG_BUILTIN_MP
flag which disables polling for MP.
Some other devices erroneously report that they support motion-plus. For
these devices and all devices without extension ports, we load
WIIMOD_NO_MP which sets WIIPROTO_FLAG_NO_MP. This effectively disables all
MP detection logic.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We now have dynamic hotplug support so the old static extensions are no
longer needed nor used. Remove it along CONFIG_HID_WIIMOTE_EXT.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Balance-Boards provide 3 16bit calibration values for each of the 4
sensors. We provide these now as 192bit value via a new "bboard_calib"
sysfs attribute.
We also re-read the calibration data from the device whenever user-space
attempts to read this file. On normal Nintendo boards, this always
produces the same results, however, on some 3rd party devices these values
change until the device is fully initialized. As I have currently no idea
how long to wait until it's ready (sometimes takes up to 10s?) we provide
a simple workaround for users by reading this file.
If we, at some point, figure out how it works, we can implement it in the
kernel and provide offline data via "bboard_calib". This won't break
user-space then.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Two new attributes, "extension" and "devtype" now allow user-space to read
the extension type and device type. As device detection is asynchronous,
we send a CHANGED event after it is done. This also allows user-space to
wait for a device to settle before opening its input event devices.
The "extension" device is compatible with the old "extension" sysfs field
(which was registered by the static extension support code).
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we write a DRM mode via debugfs, we shouldn't allow normal operations
to overwrite this DRM mode. This is important if we want to debug
3rd-party devices and we want to see what data is sent on each mode.
If we write NULL/0 as DRM, the lock is removed again so the best matching
DRM is chosen by wiimote core.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
single_open() stores the seq_file pointer in file->private_data. It stores
our ctx pointer in seq_file->private.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add parsers for motion plus data so we can hotplug motion plus extensions
and make use of them. This is mostly the same as the old static motion
plus parser.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new extension module for the classic controller so we get hotplug
support for this device. It is mostly the same as the old static classic
controller parser.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This moves the nunchuk parser over to an extension module. This allows to
make use of hotplugged Nunchuks instead of the old static parser.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds Nintendo Wii Balance Board support to the new HOTPLUG capable
wiimote core. It is mostly copied from the old extension.
This also adds Balance Board device detection. Whenever we find a device
that supports the balance-board extension, we assume that it is a real
balance board and disable unsupported hardward like accelerometer, IR,
rumble and more.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wii Remote has several extension ports. The first port (EXT) provides
hotplug events whenever an extension is plugged. The second port (MP)
does not provide hotplug events by default. Instead, we have to map MP
into EXT to get events for it.
This patch introduces hotplug support for extensions. It is fairly
complicated to get this right because the Wii Remote sends a lot of
noise-hotplug events while activating extension ports. We need to filter
the events and only handle the events that are real hotplug events.
Mapping MP into EXT is easy. But if we want both, MP _and_ EXT at the same
time, we need to map MP into EXT and enable a passthrough-mode. This will
then send real EXT events through the mapped MP interleaved with real MP
events. But once MP is mapped, we no longer have access to the real EXT
registers so we need to perform setup _before_ mapping MP. Furthermore, we
no longer can read EXT IDs so we cannot verify if EXT is still the same
extension that we expect it to be.
We deal with this by unmapping MP whenever we got into a situation where
EXT might have changed. We then re-read EXT and MP and remap everything.
The real Wii Console takes a fairly easy approach: It simply reconnects to
the device on hotplug events that it didn't expect. So if a program wants
MP events, but MP is disconnected, it fails and reconnects so it can wait
for MP hotplug events again.
This simplifies hotplugging a lot because we just react on PLUG events and
ignore UNPLUG events.
The more sophisticated Wii applications avoid reconnection (well, they
still reconnect during many weird events, but at least not during UNPLUG)
but they start polling the device. This allows them to disable the device,
poll for the extension ports to settle and then initialize them again.
Unfortunately, this approach fails whenever an extension is replugged
while it is initialized. We would loose UNPLUG events and polling the
device later will give unreliable results because the extension port might
be in some weird state, even though it's actually unplugged.
Our approach is a real HOTPLUG approch. We keep track of the EXT and
mapped MP hotplug events whenever they occur. We then re-evaluate the
device state and initialize any possible new extension or deinitialize any
gone extension. Only during initialization, we set an extension port
ACTIVE. However, during an unplug event we mark them as INACTIVE. This
guarantess that a fast UNPLUG -> PLUG event sequence doesn't keep them
marked as PLUGGED+ACTIVE but only PLUGGED.
To deal with annoying noise-hotplug events during extension mapping, we
simply rescan the device before performing any mapping. This allows us to
ignore all the noise events as long as the device is in the correct state.
Long story short: EXT and MP registers are sparsely known and we need to
jump through hoops to get reliable HOTPLUG working. But while Nintendo
needs *FOUR* Bluetooth reconnections for the shortest imaginable
boot->menu->game->menu->shutdown sequence, we now need *ZERO*.
As always, 3rd party devices tend to break whenever we behave differently
than the original Wii. So there are also devices which _expect_ a
disconnect after UNPLUG. Obviously, these devices won't benefit from this
patch. But all official devices were tested extensively and work great
during any hotplug sequence. Yay!
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
IR is the last piece that still is handled natively. This patch converts
it into a sub-device module like all other sub-devices. It mainly moves
code and doesn't change semantics.
We also implicitly sync IR data on ir_to_input3 now so the explicit
input_sync() calls are no longer needed.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Accelerometer data is very similar to KEYS handling. Therefore, convert
all ACCEL related handling into a sub-device module similar to KEYS.
This doesn't change any semantics but only moves code over to
wiimote-modules.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Each of the 4 LEDs may be supported individually by devices. Therefore,
we need one module for each device. To avoid code-duplication, we simply
pass the LED ID as "arg" argument to the module loading code.
This just moves the code over to wiimote-module. The semantics stay the
same as before.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This introduces a new sub-device module for the BATTERY handlers. It
moves the whole power_supply battery handling over to wiimote-modules.
This doesn't change any semantics or ABI but only converts the battery
handling into a sub-device module.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This introduces the first sub-device modules by converting the KEYS and
RUMBLE sub-devices into wiimote modules. Both must be converted at once
because they depend on the built-in shared input device.
This mostly moves code from wiimote-core to wiimote-modules and doesn't
change any semantics or ABI.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To avoid loading all sub-device drivers for every Wii Remote, even though
the required hardware might not be available, we introduce a module layer.
The module layer specifies which sub-devices are available on each
device-type. After device detection, we only load the modules for the
detected device. If module loading fails, we unload everything and mark
the device as WIIMOTE_DEV_UNKNOWN. As long as a device is marked as
"unknown", no sub-devices will be used and the device is considered
unsupported.
All the different sub-devices, including KEYS, RUMBLE, BATTERY, LEDS,
ACCELEROMETER, IR and more will be ported in follow-up patches to the new
module layer.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Our output queue is asynchronous but synchronous reports may wait for a
response to their request. Therefore, wake them up unconditionally if an
output report couldn't be sent. But keep the report ID intact so we don't
incorrectly assume our request succeeded.
Note that the underlying connection is required to be reliable and does
retransmission itself. So it is safe to assume that if the transmission
fails, the device is in inconsistent state. Hence, we abort every request
if any output report fails. No need to verify which report failed.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery reports are sent along every status report of the Wii Remote.
So chances are pretty high that we have an up-to-date battery
cache at any time. Therefore, initialize the battery-cache to 100% and
then return battery values from the cache if the query fails.
This works around a power_supply limitation in that it requires us to be
able to query the device during power_supply registration and
removal. Otherwise, "add" or "remove" udev events are not sent. If
we answer these requests from our cache instead, we avoid dropping these
events and no longer cause warnings printed.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nintendo produced many different devices that are internally based on the
Wii Remote protocol but provide different peripherals. To support these
devices, we need to schedule a device detection during initialization.
Device detection includes requesting a status report, reading extension
information and then evaluating which device we may be dealing with.
We currently detect gen1 and gen2 Wii Remote devices. All other devices
are marked as generic devices. More detections will be added later.
In followup patches we will be using these device IDs to control which
peripherals to initialize. For instance if a device is known to have no IR
camera, there is no need to provide the IR input device nor trying to
access IR registers. In fact, there are 3rd party devices that break if we
try things like this (hurray!).
The init_worker will be scheduled whenever we get hotplug events. This
isn't implemented, yet and will be added later. However, we need to make
sure that this worker can be called multiple times.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need constant I/O to keep the state up-to-date and not miss any
packets. Hence, call hid_hw_open() during setup and hid_hw_close() during
destruction.
These are no-ops for Bluetooth HIDP, but lets be safe.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The output queue is independent of the other wiimote modules and can run
on its own. Therefore, move its members into a separate struct so we don't
run into name collisions with other modules.
This is only a syntactic change that renames all queue members to queue.*.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-wiimote driver supports more than the Wii Remote. Nintendo
produced many devices based on the Wii Remote, which have extension
devices built-in. It is not clear to many users, that these devices have
anything in common with the Wii Remote, so fix the driver description.
This also updates the copyright information for the coming hotplugging
rework.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
power_supply core has the bad habit of calling our battery callbacks
from within power_supply_register(). Furthermore, if the callbacks
fail with an unhandled error code, it will skip any uevent that it
might currently process.
So if HID-core registers battery devices, an "add" uevent is generated
and the battery callbacks are called. These will gracefully fail due
to timeouts as they might still hold locks on event processing. One
could argue that this should be fixed in power_supply core, but the
least we can do is to signal ENODATA so power_supply core will just
skip the property and continue with the uevent.
This fixes a bug where "add" and "remove" uevents are skipped for
battery devices. upower is unable to track these devices and currently
needs to ignore them.
This patch also overwrites any other error code. I cannot see any reason
why we should forward protocol- or I/O-errors to the power_supply core.
We handle these errors in hid_ll_driver later, anyway, so just skip
them. power_supply core cannot do anything useful with them, anyway,
and we avoid skipping important uevents and confusing user-space.
Thanks a lot to Daniel Nicoletti for pushing and investigating
on this.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Reported-by: Daniel Nicoletti <dantti12@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
One firmare version in the devices the driver takes care of is
completely broken and needs periodic pokes from our side. We
implemented this as a periodic delayed queue. The idea of the pokes
was taken from the suse enterprise kernel, in particular from Libor's
"Elo touchscreen firmware M workaround".
I am quoting him here:
This patch adds periodic polling of the Elo USB touchscreens. Needed
as a workaround for devices with M-level firmware, otherwise these
devices are known to misbehave (as reported by Elo developers).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Tested-by: Petr Ostadal <postadal@suse.cz>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Egbert Eich <eich@suse.com>
Cc: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a driver for ELO 4000/4500 devices which report themselves as
HID devices, but do not really send HID events on touch. So we
introduce a new HID 'quirk' driver with a raw_event handler where we
take care of those events.
What we need additionally is an input_configured hook, because the
device does not mention anything about PRESSURE and TOUCH in its
report descriptor, but it actually generate those. So we set the bits
in the corresponding input_dev in that hook.
Thanks to Petr Ostadal who was willing to test the driver. The rest of
Cc's listed below had something to do with that driver over the years
in our enterprise tree.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Tested-by: Petr Ostadal <postadal@suse.cz>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Egbert Eich <eich@suse.com>
Cc: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add hid-huion.c with support for Huion 580 tablet, which is simple
8x5" tablet with 4000LPI resolution and 2048 levels pressure-sensitive
pen manufactured by the Chinese company Huion.
The driver fixes incorrect report descriptor sent by the device,
performs custom initialization required to switch the tablet into
its native resolution mode and inverts the in-range bit.
Signed-off-by: Martin Rusko <martin.rusko@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is sold as Tracer Sniper TRM-503, NOVA Gaming Slider X200 and
Zalman ZM-GM1, and reports too high usage maximum and logical maximum
(like 04d9:a067, but its report descriptor is different). This patch
adds its USB ID and fixes the report descriptor in the same way.
Note: I don't actually have such a mouse to test, I took the report
descriptor posted at https://bugzilla.novell.com/show_bug.cgi?id=774676,
compared it to the one from 04d9:a067 and changed the offsets
accordingly (all numbers minus 9, since it is 9 bytes shorter, and the
difference is before the values that need changing). That Surely Works™.
Signed-off-by: Christian Ohm <chr.ohm@gmx.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is sold as Sharkoon Drakonia and Perixx MX-2000 and reports a
too high usage maximum and logical maximum. This driver fixes the report
descriptor so those values don't exceed HID_MAX_USAGES.
Signed-off-by: Christian Ohm <chr.ohm@gmx.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The newly added support for Buzz controller
- introduced Kconfig selection of LEDS_CLASS
- introduced conditional preprocessor checking for CONFIG_LEDS_CLASS
This has multiple problems -- namely select doesn't work transitively,
so it shouldn't be used. On the other hand the code assumed that LEDS_CLASS
is enabled in some places, but not everywhere.
Put LEDS_CLASS as a Kconfig dependency for hid-sony and remove all the
CONFIG_LEDS_CLASS conditionals from hid-sony.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for PS2/3 Buzz controllers into hid-sony
It has been tested on Debian 7 with kernel version 3.10.0-rc2. Unfortunately
I can't test the patch with a regular six-axis controller myself.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a quirk to ignore Jabra speakerphone 410 and 510 devices HID
interface.
On those devices, the USB audio interface is working nicely,
but the HID interface is not working with the kernel usbhid driver,
and it requires a specific userspace program.
We could unbind it from userspace but just attaching the usbhid driver has
sometimes nasty effects:
either confusing the device state machine or triggering a storm of volume key
events making eventual sound UI blinking like crazy.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch also removes the duplicate entry in the hid-multitouch.c as
suggested by Benjamin Tissoires.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just sort the list by IDs. There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add vendor ID for Data Modul and their easyMaxTouch device.
The device has to be configured to multitouch mode prior to using this driver.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes 'undefined reference' issue when hid-steelseries is built in,
but led-class is a module.
--
drivers/built-in.o: In function `steelseries_srws1_remove':
hid-steelseries.c:(.text+0x3b97a1): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `steelseries_srws1_probe':
hid-steelseries.c:(.text+0x3b9c51): undefined reference to `led_classdev_register'
hid-steelseries.c:(.text+0x3b9ce5): undefined reference to `led_classdev_register'
hid-steelseries.c:(.text+0x3b9d4b): undefined reference to `led_classdev_unregister'
--
Patch allows LED control when led-class is built in, or both hid-steelseries
_and_ led-class are both modules.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It looks like the manual merge 0d69a3c731 ("Merge
branches 'for-3.9/sony' and 'for-3.9/steelseries' into for-linus") accidentally
removed Sony RF receiver with USB product id 0x0374 from the "have special
driver" list, effectively nullifying a464918419
("HID: add support for Sony RF receiver with USB product id 0x0374"). Add the
device back to the list.
Cc: stable@vger.kernel.org
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- hid driver transport cleanup, finalizing the long-desired decoupling
of core from transport layers, by Benjamin Tissoires and Henrik
Rydberg
- support for hybrid finger/pen multitouch HID devices, by Benjamin
Tissoires
- fix for long-standing issue in Logitech unifying driver sometimes not
inializing properly due to device specifics, by Andrew de los Reyes
- Wii remote driver updates to support 2nd generation of devices, by
David Herrmann
- support for Apple IR remote
- roccat driver now supports new devices (Roccat Kone Pure, IskuFX), by
Stefan Achatz
- debugfs locking fixes in hid debug interface, by Jiri Kosina
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (43 commits)
HID: protect hid_debug_list
HID: debug: break out hid_dump_report() into hid-debug
HID: Add PID for Japanese version of NE4K keyboard
HID: hid-lg4ff add support for new version of DFGT wheel
HID: icade: u16 which never < 0
HID: clarify Magic Mouse Kconfig description
HID: appleir: add support for Apple ir devices
HID: roccat: added media key support for Kone
HID: hid-lenovo-tpkbd: remove doubled hid_get_drvdata
HID: i2c-hid: fix length for set/get report in i2c hid
HID: wiimote: parse reduced status reports
HID: wiimote: add 2nd generation Wii Remote IDs
HID: wiimote: use unique battery names
HID: hidraw: warn if userspace headers are outdated
HID: multitouch: force BTN_STYLUS for pen devices
HID: multitouch: append " Pen" to the name of the stylus input
HID: multitouch: add handling for pen in dual-sensors device
HID: multitouch: change touch sensor detection in mt_input_configured()
HID: multitouch: do not map usage from non used reports
HID: multitouch: breaks out touch handling in specific functions
...
Accesses to hid_device->hid_debug_list are not serialized properly, which
could result in SMP concurrency issues when HID debugfs events are accessesed
by multiple userspace processess.
Serialize all the list operations by a mutex.
Spotted by Al Viro.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No semantic changes, but hid_dump_report should be in hid-debug.c, not
in hid-core.c
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patche adds PID of Japanese Natual Ergonomic Keyboard 4000. HID
NE4K driver depends on this PID for determining its quirks. F14-F18 keys
would not work without the patch.
Signed-off-by: Adam Jiang <jiang.adam@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It has been reported that there is a new version (different USB rev)
of the Logitech DFGT in the 'wild'.
This patch allows the kernel to recognise this wheel and send it the
command to enter native mode.
Reported-by: "Denis Jovic" <djovic78@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Magic Mouse driver also supports the Magic Trackpad, so mention it
in the KConfig description for the driver.
Signed-off-by: David King <amigadave@amigadave.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver was originally written by James McKenzie, updated by
Greg Kroah-Hartman, further updated by Bastien Nocera, with suspend
support added.
I ported it to the HID subsystem, in order to simplify it a litle
and allow lirc to use it through hiddev.
More recent versions of the IR receiver are also supported through
a patch by Alex Karpenko. The patch also adds support for the 2nd
and 5th generation of the controller, and the menu key on newer
brushed metal remotes.
Tested-by: Fabien André <fabien.andre@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kone now reports media key events through it's chardev to userspace.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In pointer_press_speed_show, we do
data_pointer = hid_get_drvdata(hdev);
twice in a row. Remove one of those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the current i2c hid driver set/get report does not work
as expected, for e.g sensor hub properties like power state,
frequency etc is not set properly on the device as a result
we do not get events.
The problem is that i2c hid driver in function i2c_hid_request
sets length equal to default buffer size for which the sensor
hub does not respond on get/set commands. Use report length
and calculate it based on report size and id.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Huzefa Kankroliwala <huzefa.nomanx.kankroliwala@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since kernel 3.7, it appears that the input registration occured before
the end of magicmouse_setup_input(). This is shown by receiving a lot of
"EV_SYN SYN_REPORT 1" instead of normal "EV_SYN SYN_REPORT 0".
This value means that the output buffer is full, and the user space
is loosing events.
Using .input_configured guarantees that the race is not occuring, and that
the call of "input_set_events_per_packet(input, 60)" is taken into account
by input_register().
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=908604
Cc: stable@vger.kernel.org
Reported-and-Tested-By: Clarke Wixon <cwixon@usa.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It turns out the Wii accepts any status reports from clients reduced to
"BB BB" key data only, as long as the report actually includes key data at
the first two bytes.
The official devices don't send these reduced reports, but of course, 3rd
party devices make great use of this feature.
Hence, add parsers for these reduced reports for every matching report.
Also change the logic how we find handlers. There is no reason to call
multiple handlers on a single report, but instead find the best handler
and call it only once.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds the 2nd generation Wii Remote IDs. They have a different
Bluetooth chipset (CSR instead of Broadcom) and are more restrictive in
what they accept as input. Hence, you need up-to-date BlueZ and
Bluetooth HIDP modules to use these devices.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery device names must be unique, otherwise registration fails if
multiple Wii Remotes are connected.
This breaks the sysfs API, but there is no known application that uses the
Wii Remote battery that I know of so we should go ahead and apply this.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch reverts commit 0322bd3980 ("usb hid quirks for Masterkit MA901 usb
radio") and adds checks in hid_ignore() for Masterkit MA901 usb radio device.
This usb radio device shares USB ID with many Atmel V-USB (and probably other)
devices so patch sorts things out by checking name, vendor, product of hid device.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for potential 3.9 regression in handling of buttons for touchpads
following HID mt specification; potential because reportedly there is
no retail product on the market that would be using this feature, but
nevertheless we'd better follow the spec. Fix by Benjamin Tissoires.
- support for two quirky devices added by Josh Boyer.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: fix touchpad buttons
HID: usbhid: fix build problem
HID: usbhid: quirk for MSI GX680R led panel
HID: usbhid: quirk for Realtek Multi-card reader
Commit "HID: multitouch: use the callback "report" instead..." breaks the
buttons of touchpads following the HID multitouch specification.
The buttons were emmitted through hid-input, but as now the events
are generated only in hid-multitouch, the buttons are not emmitted anymore.
The input_event() call is far much simpler than the hid-input one as
many of the different tests do not apply to multitouch touchpads.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The "tablet" udev rule relies on BTN_STYLUS to be set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is not just cosmetics, it can help to write udev and X.org
rules.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dual sensors devices reports pen and touch on two different reports.
Using the quirk HID_QUIRK_MULTI_INPUT allows us to create a new input
device to forward pen events.
The quirk HID_QUIRK_NO_EMPTY_INPUT avoids the creation of input devices
for the not used mouse emulation present on Win7 certified devices.
Since hid-multitouch sets the quirk HID_QUIRK_NO_INPUT_SYNC, we need
to manually send SYN events for pen report too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To implement different methods for pen and touch, the previous
implementation has to be reworked.
This detection of the input attached to the touch sensor is the same
than the one used in mt_report().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-multitouch only handles touch events, so there is no point in
mapping other kind of events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will allow easier integration of hybrid pen and touch devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no need to register an input device containing no events.
This allows drivers using the quirk MULTI_INPUT to register one input
per report effectively used.
For backward compatibility, we need to add a quirk to request
this behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let the system sleep go ahead further, so this
patch doesn't recover device under this situation, otherwise
may cause resume() confused.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build problem caused by typo introduced by 620ae90ed8
("HID: usbhid: quirk for MSI GX680R led panel").
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This keyboard backlight device causes a 10 second delay to boot. Add it
to the quirk list with HID_QUIRK_NO_INIT_REPORTS.
This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=907221
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Extending isku module with one additional and one changed sysfs attr. IskuFX has
larger light sysfs attr. Made the code size tolerant so both devices can be
handled.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userland-tools can already be found at http://sourceforge.net/projects/roccat
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sync with Linus' tree. This is necessary to resolve build conflict
caused by dcd9006b1b ("HID: logitech-dj: do not directly call
hid_output_raw_report() during probe") which issues direct call to
usbhid_submit_report(), but that is gone in this branch and
hid_hw_request() has to be used instead.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fix from Jiri Kosina:
"Bugfix for a long-standing bug in logitech-dj driver causing all sorts
of random initialization problems, finally debugged by Benjamin
Tissoires with help of Bob Bowles."
* 'for-3.9/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: logitech-dj: do not directly call hid_output_raw_report() during probe
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143https://bugzilla.redhat.com/show_bug.cgi?id=840391https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-multitouch used to direclty call for a set_idle in the .resume()
callback. With the new hid_hw_idle(), this can be dropped and
hid-multitouch is now freed from its transport layer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers send the idle command directly to underlying device,
creating an unwanted dependency on the underlying transport layer.
This patch adds hid_hw_idle() to the interface, thereby removing
usbhid from the lion share of the drivers.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the HID drivers tranport cleanup series, I removed the dependency
between hid-holtek and usbhid. This was wrong as hid-holtek.c relies
extensively on usb calls.
This fixes compilation error when CONFIG_USB_SUPPORT is not enabled.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The aim of last_field_index was to detect the end of the report.
With the introduction of .report(), it is not required anymore to
detect it on the fly as we can put it in the right place during the
.report().
The resulting code path is simpler to read because the terminating
condition is not evaluated after each field.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 596264082f.
The reverted commit was a workaround needed when drivers became unable
to communicate with devices during probe(). Now that such
communication is possible, the workaround is not needed.
Signed-off-by: Andrew de los Reyes <adlr@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Historically, logitech-dj communicated with the device during probe()
to query the list of devices attached. Later, a change was introduced
to hid-core that prevented incoming packets for a device during
probe(), as many drivers are unable to handle such input. That change
broke the device enumeration in logitech-dj, so commit
596264082f was introduced to workaround that by waiting for
normal input before enumerating devices.
Now that drivers can opt-in to receive input during probe, this patch
changes logitech-dj to do that, so that it can successfully complete
enumeration of devices during probe().
Signed-off-by: Andrew de los Reyes <adlr@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch separates struct hid_device's driver_lock into two. The
goal is to allow hid device drivers to receive input during their
probe() or remove() function calls. This is necessary because some
drivers need to communicate with the device to determine parameters
needed during probe (e.g., size of a multi-touch surface), and if
possible, may perfer to communicate with a device on host-initiated
disconnect (e.g., to put it into a low-power state).
Historically, three functions used driver_lock:
- hid_device_probe: blocks to acquire lock
- hid_device_remove: blocks to acquire lock
- hid_input_report: if locked returns -EBUSY, else acquires lock
This patch adds another lock (driver_input_lock) which is used to
block input from occurring. The lock behavior is now:
- hid_device_probe: blocks to acq. driver_lock, then driver_input_lock
- hid_device_remove: blocks to acq. driver_lock, then driver_input_lock
- hid_input_report: if driver_input_lock locked returns -EBUSY, else
acquires driver_input_lock
This patch also adds two helper functions to be called during probe()
or remove(): hid_device_io_start() and hid_device_io_stop(). These
functions lock and unlock, respectively, driver_input_lock; they also
make a note of whether they did so that hid-core knows if a driver has
changed the lock state.
This patch results in no behavior change for existing devices and
drivers. However, during a probe() or remove() function call in a
driver, that driver may now selectively call hid_device_io_start() to
let input events come through, then optionally call
hid_device_io_stop() to stop them.
Signed-off-by: Andrew de los Reyes <adlr@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Instead of limiting HID sensors to USB and I2C busses we can just make
everything that has usage page of HID_UP_SENSOR to be included in
HID_GROUP_SENSOR_HUB group. This allows the sensor-hub to work over
bluetooth (and other transports) as well.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows HID drivers to also get/set reports through hid_hw_request().
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reflects my new company and officialize the regression tests I'm
conducting between each change.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch is part of the cleanup of the HID drivers
against their low-level transport layer.
With new touchscreens relying on I2C, it's better to
handle now these dependencies before users get kernel oopses.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes most of the dependencies between hid drivers and usbhid.
The patch was constructed by replacing all occurences of
usbhid_wait_io() by its hid_hw_wait() counterpart.
Then, drivers not requiring USB_HID anymore have their USB_HID
dependency cleaned in the Kconfig file.
As of today, few drivers are still requiring an explicit USB layer
dependency:
* ntrig (a patch is on its way)
* multitouch (one patch following and another on its way)
* lenovo tpkbd
* roccat
* sony
The last three are two deeply using direct calls to the usb subsystem
to be able to be cleaned right now.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows the hid drivers to be independent from the transport layer.
The patch was constructed by replacing all occurences of
usbhid_submit_report() by its hid_hw_request() counterpart.
Then, drivers not requiring USB_HID anymore have their USB_HID
dependency cleaned in the Kconfig file.
Finally, few drivers still depends on USB_HID. Many of them
are requiring the io wait callback. They are found in the next patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the sensor-hub part:
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most HID drivers (rightfully) only depend on the HID bus, not the
specific transport layer. Remove such dependencies where applicable.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers need to wait for an io from the underlying device, creating
an unwanted dependency on the underlying transport layer. This patch adds
wait() to the interface, thereby removing usbhid from the lion share of
the drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers send reports directly to underlying device, creating an
unwanted dependency on the underlying transport layer. This patch adds
hid_hw_request() to the interface, thereby removing usbhid from the
lion share of the drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
Pull HID subsystem updates from Jiri Kosina:
"HID subsystem and drivers update. Highlights:
- new support of a group of Win7/Win8 multitouch devices, from
Benjamin Tissoires
- fix for compat interface brokenness in uhid, from Dmitry Torokhov
- conversion of drivers to use hid_driver helper, by H Hartley
Sweeten
- HID over I2C transport received ACPI enumeration support, written
by Mika Westerberg
- there is an ongoing effort to make HID sensor hubs independent of
USB transport. The first self-contained part of this work is
provided here, done by Mika Westerberg
- a few smaller fixes here and there, support for a couple new
devices added"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (43 commits)
HID: Correct Logitech order in hid-ids.h
HID: LG4FF: Remove unnecessary deadzone code
HID: LG: Prevent the Logitech Gaming Wheels deadzone
HID: LG: Fix detection of Logitech Speed Force Wireless (WiiWheel)
HID: LG: Add support for Logitech Momo Force (Red) Wheel
HID: hidraw: print message when succesfully initialized
HID: logitech: split accel, brake for Driving Force wheel
HID: logitech: add report descriptor for Driving Force wheel
HID: add ThingM blink(1) USB RGB LED support
HID: uhid: make creating devices work on 64/32 systems
HID: wiimote: fix nunchuck button parser
HID: blacklist Velleman data acquisition boards
HID: sensor-hub: don't limit the driver only to USB bus
HID: sensor-hub: get rid of unused sensor_hub_grabbed_usages[] table
HID: extend autodetect to handle I2C sensors as well
HID: ntrig: use input_configured() callback to set the name
HID: multitouch: do not use pointers towards hid-core
HID: add missing GENERIC_HARDIRQ dependency
HID: multitouch: make MT_CLS_ALWAYS_TRUE the new default class
HID: multitouch: fix protocol for Elo panels
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
Reorders a couple of device IDs (Logitech controllers) to ensure
that they are in hexidecimal order.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch removes code which is now unnecessary for setting the fuzz/flat
characterics for the logitech DFP wheel. This is now done in the previous
patch by marking the wheel as a multi-axis device.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch ensures that the Logitech wheels are not initialised with
default fuzz/flat values, by marking them as multiaxis devices (rather
than joysticks).
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously 'LG4FF' was only used for the WiiWheel, however it is now used
for all the Logitech Wheels. This patch corrects the detection mechanism
for the patching the report descriptor to ensure only the WiiWheel will
be patched.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch provides a modified report descriptor to split accelerator
and brake, and adds the 'NO_GET' flag to prevent it hanging on
connection.
Note: for convience this patch is against the follow patch which was applied
earlier this week.
https://patchwork.kernel.org/patch/2153471/
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is the original report descriptor as reported by lsusb -vd 046d:c294.
Signed-off-by: Paul Sbarra <sbarra.paul@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ThingM blink(1) is an open source hardware USB RGB LED. It contains
an internal EEPROM, allowing to configure up to 12 light patterns. A
light pattern is a RGB color plus a fade time. This driver registers a
LED class instance with additional sysfs attributes to support basic
functions such as setting RGB colors, fade and playing. Other functions
are still accessible through the hidraw interface.
At this time, the only documentation for the device is the firmware
source code from ThingM, plus a few schematics. They are available at:
https://github.com/todbot/blink1
This patch is version 3. It updates the name of the source file, the
driver and the led sysfs entry, according to comments from Jiri Kosina
and Simon Wood.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unfortunately UHID interface, as it was introduced, is broken with 32 bit
userspace running on 64 bit kernels as it uses a pointer in its userspace
facing API.
Fix it by checking if we are executing compat task and munge the request
appropriately.
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The buttons of the Wii Remote Nunchuck extension are actually active low.
Fix the parser to forward the inverted values. The comment in the function
always said "0 == pressed" but the implementation was wrong from the
beginning.
Cc: stable@vger.kernel.org
Reported-by: Victor Quicksilver <victor.quicksilver@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are simple data acquistion boards, not HID devices and are handled
by the vmk80xx comedi driver. At least one of them (10cf:5500)
misidentifies itself as a HID in its USB interface descriptor. Ignore
all these devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We now have two transport mediums: USB and I2C, where sensor hubs can
exists. So instead of constraining the driver to only these two we let it
to match any HID bus as long as the group is HID_GROUP_SENSOR_HUB.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This table is not used anywhere in the driver so kill it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the advent of HID over I2C protocol, it is possible to have sensor
hubs behind I2C bus as well. We can autodetect this in a same way than USB
sensor hubs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The use of input_configured() allows the ntrig driver to actually
change the name of the input and its bitmask before it is added to the
input subsystem. Thus, the logs are coherents and udev catch the real
bitmask when the device is added.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The previous implementation registered a pointer towards hid-core
to the value of contact count. This is not safe and may be difficult
to debug if hid-core ever changes its implementation.
The use of regular indexes is a better choice.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID Sensors framework support (CONFIG_HID_SENSOR_HUB) unconditionally
selects MFD_CORE which however depends on GENERIC_HARDIRQS.
So add this dependency to HID_SENSOR_HUB as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By running a test on all the traces of the devices I have,
I noticed that the class MT_CLS_ALWAYS_TRUE could handle all
the devices I've seen so far without any other quirks.
I guess this is the behavior Win 7 requires in its driver.
We can change the default class then and keep the existing classes
for backward compatibility and performances for some of them.
Two operations have been done:
* replaced MT_CLS_DEFAULT by MT_CLS_NSMU
* then replaced MT_CLS_ALWAYS_TRUE by MT_CLS_DEFAULT
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The previous protocol was nearly working, but when several fingers were
present on the sensor, those that were not moving were not updated
in the next report, introducing a lot of releases.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Conflicts:
drivers/hid/hid-multitouch.c
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cando 2087:0a02 was broken, this fixes it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the inclusion of this device in hid-multitouch, the device
did not forward any events. Using the serial class makes it working
again.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The serial protocol makes contact count a redondant information, and
sometimes it is not reliable (TRS-Star are in this case).
Disabling the use of contact count for these devices is thus safer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Sharp LC-20FE1-W screen (04dd:9681) behaves like the Nexio 42".
It may report out of ranges values that are filtered out by relying
on the Contact Count HID field.
Adding the quirk MT_QUIRK_CONTACT_CNT_ACCURATE makes hid-multitouch
strongest against this kind of device, without breaking the current
devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device is the worst device I saw. It keeps TipSwitch and InRange
at 1 for fingers that are not touching the panel.
The solution is to rely on the field ContactCount, which is accurate
as the correct information are packed at the begining of the frame.
Unfortunately, CountactCount is most of the time at the end of the report.
The solution is to pick it when we have the whole report in raw_event.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nexio 42" devices requires to rely on the HID field Contact
Count to compute the valid values. However, this field is
most of the time at the end of the report, meaning that we
need to get the all report parsed before processing it.
This patch does not introduce functional changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This callback is called when the parsing of the report has been done
by hid-core (so after the calls to .event). The hid drivers can now
have access to the whole report by relying on the values stored in
the different fields.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The last field of the driver_data->leds[] array is used to store the
special toggle for setting all leds simultaneously, so we need to allocate
appropriate number of led_classdev pointers.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We usually group drivers on a per-vendor basis, implementing device-specific
deviations from the standard in vendor-specific driver.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver adds the ability to control all
LEDs simultaneously as testing showed that it was slow (noticably!!)
when seting or clearing all the LEDs in turn.
It adds a 'RPMALL' LED, whose behavoir is asserted to all the LEDs in
the bar graph, individual LEDs can subsequently be turned on/off
individually.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver adds support for the LED RPM
meter on the front of the device. The LEDs are controlled via
/sys/class/leds interface, with an individual control for each
of the 15 LEDs.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver re-writes the HID descriptor
to insert a section for the 3 dials on the device, previously
these were contained within a 'Manufacturer Specific' usage
page.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support the SRW-S1 by patching HID descriptor to read axis
as Generic Desktop X, Y and Z (rather than Usage page being
'Simulation').
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the consolidated GUID definitions in the Hyper-V mouse driver.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
Document what the fix-up is does and make it more robust by ensuring
that it is only applied to the USB interface that corresponds to the
mouse (sony_report_fixup() is called once per interface during probing).
Cc: linux-input@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID over I2C protocol specification states that when the device is
enumerated from ACPI the HID descriptor address can be obtained by
executing "_DSM" for the device with function 1. Enable this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This variable is initialized conditionally, based on whether a wiimote
call succeeds. However, the logic is not obvious to the compiler so it
throws a warning. Eliminate the warning by initializing "size" to 0.
The warning is:
files/drivers/hid/hid-wiimote-debug.c:69:18: warning: 'size' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for another gamepad to the hid-pl driver. The "color rumble pad
P580" marketed using the "Saitek" brand in Germany, and using a USB Vendor ID
attributed to "Jess" seems to be electronically identical to the 4-field
variant of the "Green Asia" gamepad.
The pad has been tested to support rumble strengths up to 255, not just 127.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch to add the Formosa Industrial Computing, Inc. Infrared Receiver
[IR605A/Q] to hid-ids.h and hid-quirks.c. This IR receiver causes about a 10
second timeout when the usbhid driver attempts to initialze the device. Adding
this device to the quirks list with HID_QUIRK_NO_INIT_REPORTS removes the
delay.
Signed-off-by: Nicholas Santos <nicholas.santos@gmail.com>
[jkosina@suse.cz: fix ordering]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are some Sony clone gamepads that are incompatible
with PS3 since firmware 3.50, as they decided to prevent those
devices to work, without any good technical reason. I was one of those
'blessed' people affected by their niceness with their customers.
Marcelo also has another device with a similar problem.
Perhaps due to Sony's way to block the device, damaging the device's
eeprom, or perhaps because they just have a different, broken Report
descriptor, there are 3 buttons that don't work on both devices
(the ones equivalent to square, round and X).
What it happens is that the descriptor generate weird EV_ABS events
to those buttons, instead of EV_MSC/EV_KEY.
A fix that seems to be enough for them is to return the original
sixaxis table instead of the broken one. That's what this patch
does.
Yet, there are some missing entries at the used keytable. On my
tests, all keys are now producing the right events, but the reported
keycodes look weird:
"square" key: (Button.0010 = 1)
1355524363.460835: event type EV_MSC(0x04): scancode = 0x90010
1355524363.460835: event type EV_KEY(0x01) key_up: BTN_DEAD(0x0001)
"round" key: (Button.000e = 1)
1355524410.908705: event type EV_MSC(0x04): scancode = 0x9000e
1355524410.908705: event type EV_KEY(0x01) key_down: (0x0001)
1355524410.971788: event type EV_MSC(0x04): scancode = 0x9000e
1355524410.971788: event type EV_KEY(0x01) key_up: (0x0001)
"X" key: (Button.000f = 1)
1355524384.880813: event type EV_MSC(0x04): scancode = 0x9000f
1355524384.880813: event type EV_KEY(0x01) key_down: (0x0001)
1355524384.979815: event type EV_MSC(0x04): scancode = 0x9000f
1355524384.979815: event type EV_KEY(0x01) key_up: (0x0001)
The rationale is likely due to those entries at rdesc table, where the
Kernel were not likely able to parse:
Button.000d ---> Key.?
Button.000e ---> Key.?
Button.000f ---> Key.?
Button.0010 ---> Key.BtnDead
Button.0011 ---> Key.?
Button.0012 ---> Key.?
Button.0013 ---> Key.?
As a reference, this is the rdisc used on my clone (a Mad Catz
model 8846):
05 01 09 04 a1 01 a1 02 85 01 75 08 95 01 15 00 26 ff 00 81 03 75 01 95 0d 15 00 25 01 35 00 45 01 05 09 19 01 29 0d 81 02 75 01 95 03 06 00 ff 81 03 05 01 25 07 46 3b 01 75 04 95 01 65 14 09 39 81 42 65 00 75 01 95 0c 06 00 ff 81 03 15 00 26 ff 00 05 01 09 01 a1 00 75 08 95 04 15 00 15 00 15 00 35 00 35 00 46 ff 00 09 30 09 31 09 32 09 35 81 02 c0 05 01 75 08 95 27 09 01 81 02 75 08 95 30 09 01 91 02 75 08 95 30 09 01 b1 02 c0 a1 02 85 02 75 08 95 30 09 01 b1 02 c0 a1 02 85 ee 75 08 95 30 09 01 b1 02 c0 a1 02 85 ef 75 08 95 30 09 01 b1 02 c0 c0
This is what's returned on Marcelo's device (not sure what is
the brand name of his device):
05 01 09 04 a1 01 a1 02 85 01 75 08 95 01 15 00 26 ff 00 81 03 75 01 95 13 15 00 25 01 35 00 45 01 05 09 19 01 29 13 81 02 75 01 95 0d 06 00 ff 81 03 15 00 26 ff 00 05 01 09 01 a1 00 75 08 95 04 35 00 46 ff 00 09 30 09 31 09 32 09 35 81 02 c0 05 01 95 13 09 01 81 02 95 0c 81 01 75 10 95 04 26 ff 03 46 ff 03 09 01 81 02 c0 a1 02 85 02 75 08 95 30 09 01 b1 02 c0 a1 02 85 ee 75 08 95 30 09 01 b1 02 c0 a1 02 85 ef 75 08 95 30 09 01 b1 02 c0 c0
Reported-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the new module_hid_driver macro in all HID drivers that have
a simple register/unregister init/exit.
This also converts the hid drivers that test for a failure of
hid_register_driver() and report the failure. Using module_hid_driver
in those drivers removes the failure message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't let Masterkit MA901 USB radio be handled by usb hid drivers.
This device will be handled by radio-ma901.c driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
We should not enter close function while someone else is in open.
This mutex prevents this race.
There is also no need to override the ret value with -EIO in case of
a failure of i2c_hid_set_power.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It should not be necessary to add IDs for HID sensor hubs to lists in
hid-core.c and hid-sensor-hub.c. So instead of a whitelist, autodetect such USB
HID sensor hubs, based on a collection of type physical inside a useage page of
type sensor. If some sensor hubs stil must be usable as raw devices, a
blacklist might be created.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: "Pandruvada, Srinivas" <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch against kernel 3.7.0-rc8 fixes a kernel oops when turning on the
bluetooth mouse with id 0458:0058 [1].
The mouse in question supports both input and hid sessions, however it is
blacklisted in drivers/hid/hid-core.c so the input session is one that should
be used. Long ago (around kernel 3.0.0) some changes in the bluetooth
subsystem made the kernel do not fallback to input session when hid session is
not supported or blacklisted. This patch restore that behaviour by making the
kernel try the input session if hid_add_device returns ENODEV.
The patch exports hid_ignore() from hid-core.c so that it can be used in the
bluetooth subsystem.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=39882
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ret_count has to be at least 3, as we have to count the 2 bytes that are used
for the size of the reply. Without this, memcpy() might be called with zero or
negative count.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The previous memcpy implementation relied on the size advertized by the
device. There were no guarantees that buf was big enough.
Some gymnastic is also required with the +2/-2 to take into account
the first 2 bytes of the returned buffer where the total returned
length is supplied by the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point in keeping the irq in i2c_hid as it's already
there in client.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies i2c_hid_alloc_buffers tests, and makes this function
responsible of the assignment of ihid->bufsize.
The condition for the reallocation in i2c_hid_start is then simpler.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID descriptors contains 4 bytes of reserved field.
The previous implementation was overriding the next fields in struct i2c_hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The pointless WARN_ON() has been removed from i2c_hid_remove(),
so we don't need bug.h any more.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ihid can not be null, so there are no reasons to test it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If i2c_hid_get_report fails, exit i2c_hid_init_report.
The printk log is already called by i2c_hid_get_report, so no need
to add some more printks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the case where the hid driver in charge of handling the hid part
of the device (hid-generic for instance) fails at probe, neither
i2c_hid_start nor i2c_hid_stop are called.
Thus, the buffers allocated in i2c_hid_probe are never freed.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Forwards appropriate return values.
As noone use the error returned by i2c_hid_get_input, let's make it
returning void.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These definitions are not used here, but are defined by the specification.
Keeping some of them for documentation purposes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This avoids the problematic case:
if (condition)
i2c_hid_dbg(ihid, "Blah blah %d\n", i);
else
do_something_very_important();
Which looks correct, however with the previous macro definition,
this expands to the unexpected:
if (condition) {
if (debug) \
dev_printk(KERN_DEBUG, &ihid->client->dev,
"Blah blah %d\n", i);
else
do_something_very_important();
}
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We should not initialize to 0 static declarations.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The "comment" part can never be displayed, so we can remove it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
no I2C driver has "i2c" in its name. It makes more sense to call this
i2c driver "hid".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 0a97e1e9f9 ('HID: apple: Add Apple wireless keyboard 2011 ANSI PID')
did not update the special driver list in hid-core.c, so hid-generic may
still bind to this device.
Reported-by: Ari Pollak <ari@scvngr.com>
References: http://bugs.debian.org/694546
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This just refactors the allocation of hid_input.
No semantic changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes sending SIGIO from hidraw_report_event by creating a fasync
handler which adds the fasync entry.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
When the file has been open in non-blocking mode, EIO or ERESTARTSYS
would never be returned even if they should (for example when device
has been unplugged, you want EIO and not EAGAIN to be returned).
Move the O_NONBLOCK check after other checks have been performed.
Base on similar patch done to hidraw by
Founder Fang <founder.fang@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB recovery mode present in i.MX23 ROM emulates USB HID. It needs this
quirk to behave properly.
Even if the official branding of the chip is Freescale i.MX23, I named it
Sigmatel STMP3780 since that's what the chip really is and it even reports
itself as STMP3780.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When nonblock read the condition check (file->f_flags & O_NONBLOCK) always be
true, signal_pending and device exist checking never get a chance to run, so
the user mode code always get EAGAIN even if device removed. move nonblock mode
checking to the last can fix this problem.
Signed-off-by: Founder Fang <founder.fang@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support to Novatec wireless mouse (device ID 0603:1602).
Fixes bug https://bugzilla.kernel.org/show_bug.cgi?id=47031
Signed-off-by: Marco Biscaro <marcobiscaro2112@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In case we are returning from i2c_hid_probe() through the 'err' or
'err_mem_free' labels, there is noone freeing the buffers allocated by
i2c_hid_alloc_buffers().
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
report cannot be NULL, fortunately as we use it before we check !
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft published the protocol specification of HID over i2c:
http://msdn.microsoft.com/en-us/library/windows/hardware/hh852380.aspx
This patch introduces an implementation of this protocol.
This implementation does not includes the ACPI part of the specification.
This will come when ACPI 5.0 devices enumeration will be available.
Once the ACPI part is done, OEM will not have to declare HID over I2C
devices in their platform specific driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
More thorough testing revealed a typo in last koneplus cleanups.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fix from Jiri Kosina:
"This has a build fix for architectures where memcmp() is macro, from
Jiri Slaby"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: microsoft: do not use compound literal - fix build
No need to check whether unsigned variable is less than 0.
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-usb@vger.kernel.org
CC: linux-input@vger.kernel.org
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Win 8 protocol specify the fact that each valid touch must be reported
within a frame until it is released.
We can therefore use the always_valid quirk and dismiss reports when we see
duplicate contacts ID.
We recognize Win8 certified devices from their vendor feature 0xff0000c5
where Microsoft put a signed blob in the report to check if the device
passed the certification.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Win8 devices supporting hovering must provides InRange HID field.
The information that the finger is here but is not touching the surface
is sent to the user space through ABS_MT_DISTANCE as required by the
multitouch protocol.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This quirk allows a device to reuse a contact id when sending garbage
inactive contacts at the end of a report.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Win 8 device specification changed the requirements for the hid usages
of the multitouch devices. Now InRange is optional and must be only
used when the device supports hovering.
This ensures that the quirk ALWAYS_VALID is taken into account and
also ensures its precedence over the other VALID* quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Win8 input specification clarifies the X and Y sent by devices.
It distincts the position where the user wants to Touch (T) from
the center of the ellipsoide (C). This patch enable supports for this
distinction in hid-multitouch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Win8 devices are required to present the feature "Maximum Contact Number".
Fortunately all win7 devices I've seen presents this feature.
If the current value is 0, then, the driver can get the actual supported
contact count by refering to the logical_max.
This win8 specification ensures that logical_max may not be above 250.
This also allows us to detect when devices like irtouch or stantum reports
an obviously wrong value of 255.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Win8 certification introduced the ability to transmit two X and two Y per
touch. The specification precises that it must be used in an array.
This test guarantees that we split the touches on the last element
in this array.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, there is no way to know the index of the current field
in the .input_mapping and .event callbacks when this field is inside
an array of HID fields.
This patch adds this index to the struct hid_usage so that this
information is available to input_mapping and event callbacks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID spec details special values for the HID field unit exponent.
Basically, the range [0x8..0xf] correspond to [-8..-1], so this is
a standard two's complement on a half-byte.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidinput_calc_abs_res should return the closest int in the division
instead of the floor.
On a device with a logical_max of 3008 and a physical_max of 255mm,
previous implementation gave a resolution of 11 instead of 12.
With 11, user-space computes a physical size of 273.5mm and the
round_closest results gives 250.6mm.
The old implementation introduced an error of 2cm in this example.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Exporting the function allows us to calculate the resolution in third
party drivers like hid-multitouch.
This patch also complete the function with additional valid axes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In patch "HID: microsoft: fix invalid rdesc for 3k kbd" I fixed
support for MS 3k keyboards. However the added check using memcmp and
a compound statement breaks build on architectures where memcmp is a
macro with parameters.
hid-microsoft.c:51:18: error: macro "memcmp" passed 6 arguments, but takes just 3
On x86_64, memcmp is a function, so I did not see the error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduced attribute "control" and made profile_settings and profile_buttons
readable, which makes profile[1-5]_settings and profile[1-5]_buttons obsolete.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduced attribute "control" and made profile_settings and profile_buttons
readable, which makes profile[1-5]_settings and profile[1-5]_buttons obsolete.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduced attribute "control" and made profile_settings and profile_buttons
readable, which makes profile[1-5]_settings and profile[1-5]_buttons obsolete.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Isku needs an extra sysfs attr to support device reset.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed unneeded structures from header.
Using enums instead of sizeof(struct) to unify drivers.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Partially removed unneeded informations and data caching.
Moved code nearer to format of newer drivers.
Added "info" sysfs attribute to support device reset and deprecate
"firmware_version" attribute.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Partially removed unneeded informations and data caching.
Moved code nearer to format of newer drivers.
Added "info" sysfs attribute to support device reset and deprecate other attributes.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fix from Jiri Kosina:
"This reverts a patch that causes regression in binding between HID
devices and drivers during device unplug/replug cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hidraw: put old deallocation mechanism in place
Previously, both usbhid and usbtouchscreen would bind to D-WAV devices
with class HID and protocol None, so they would be claimed by whichever
driver was loaded first. Some of these devices do in fact work with
usbhid, but not all of them do. OTOH they all work with usbtouchscreen
as of commit 037a833ed0 ("Input:
usbtouchscreen - initialize eGalax devices"). So we ignore them in
usbhid to prevent getting in the way of usbtouchscreen and claiming an
interface that we may not be able to do anything useful with.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed caching of profile data which lowers memory footprint,
speeds up init and fixes problems with device reset.
Removed unnecessary infos in header.
Code moved nearer to format of newer drivers.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Forest Bond