Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use the dmaengine based Tegra APB DMA driver for
apbio access in place of legacy Tegra APB DMA.
The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/pr_err/pr_debug/ in tegra_apb_dma_init; this condition is
expected to fire repeatedly before the DMA driver is available]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 HW issue with accessing APBIO registers (such
as fuse registers) directly from the CPU concurrently with
APB DMA accesses has been fixed in Tegra30 and later chips.
Access these registers directly from the CPU on Tegra30
and later, and apply the workaround only for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A subsequent patch will add a generic PWM API driver for the Tegra PWFM
controller, supporting all four PWM devices with a single PWM chip. The
device will be named tegra-pwm and only one clock needs to be provided.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
PWM clock source registers in Tegra 2 have different clock source selection bit
fields than other registers. PWM clock source bits in CLK_SOURCE_PWM_0 register
are located at bit field bit[30:28] while others are at bit field bit[31:30] in
their respective clock source register.
This patch updates the clock programming to correctly reflect that, by adding a
flag to indicate the alternate bit field format and checking for it when
selecting a clock source (parent clock).
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
of_default_bus_match_table is a table of default bus types supported by
of_platform_populate(). Since Tegra has no need to support any specific
custom list of bus types, modify the DT board files to use this default
list.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Rename the driver name of the clock entry of Tegra APBDMA to
tegra-apbdma from of tegra-dma.
This name is more aligned towards the movement of dmaengine based
new DMA driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
In Tegra30 clock file two clk objects were created for same UART clock.
Remove the duplicates and add clock aliases instead.
Update the Tegra20 clock file to make the names consistent.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There currently aren't bindings for a WiFi rfkill button, and defining
a good binding is non-trivial. Manually register this "device" when
booting from device tree, in order to bring DT support to the same
feature level as board files, which will in turn allow board files to be
deprecated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There currently aren't bindings for the Tegra PCIe controller. Work on
this is in progress, but not yet complete. Manually initialize PCIe when
booting from device tree, in order to bring DT support to the same
feature level as board files, which will in turn allow board files to be
deprecated.
PCIe on Harmony requires various regulators to be registered and enabled
before initializing the PCIe controller. Note that since the I2C
controllers are instantiated from DT, we must use i2c_new_device() to
register the PMU rather than i2c_register_board_info().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There currently aren't bindings for the Tegra PCIe controller. Work on
this is in progress, but not yet complete. Manually initialize PCIe when
booting from device tree, in order to bring DT support to the same
feature level as board files, which will in turn allow board files to be
deprecated.
PCIe hosts the wired Ethernet controller on TrimSlice.
To support this, add infra-structure to board-dt-tegra20.c for board-
specific initialization code. Once device tree support for the relevant
features is in place, this code will be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Seaboard device tree supports all the features that the Seaboard
board files support. Hence, there's no need to keep the board files
around any more; all users should convert to device tree.
MACH_KAEN and MACH_WARIO are also removed. While tegra-seaboard.dts
doesn't support those explicitly, it would be trivial to create device
trees for those boards if anyone cares.
The Seaboard device tree is now compiled if Tegra2 support is enabled,
rather than when Seaboard support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Make ARCH_TEGRA select USE_OF; DT is the way forward.
* Build board-dt-tegra*.c when the relevant Tegra SoC support is enabled,
rather than requiring a specific config option for this.
* The board-specific config options already build board-*-pinmux.o, and
when booting from device tree these files are no longer needed, so we
can remove some Makefile commands related to those files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Update Makefile.boot to compile *.dts when the appropriate Tegra SoC
support is enabled, rather than requiring Kconfig to list each board
individually. Remove CONFIG_MACH_VENTANA now that it has no use.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
powergate functions are needed for tegra30 as well (see common.c), so
build it always. Fixes:
arch/arm/mach-tegra/built-in.o: In function `tegra30_init_early':
apbio.c:(.init.text+0x78): undefined reference to `tegra_powergate_init'
(using "allnoconfig" with tegra30 enabled)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.
Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This solves a section mismatch warning. I hadn't noticed this before,
because my compiler was inlining tegra_cpu_reset_handler_enable() inside
tegra_cpu_reset_handler_init(), which is already __init, but I switched
compilers and it stopped doing that.
Cc: <stable@kernel.org> # v3.4
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Tested on Ventana and Cardhu.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra ASoC machine drivers only depend on Tegra architecture support
to compile, not specific board support. Remove Kconfig dependencies on
any particular board. This is required since Kconfig options for boards
are going away given the migration to device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This particular code had no effect on WFI execution. It only
asserts/de-asserts signal to tegra "legacy" CPU idle stats
monitor, which we are no longer using (cpufreq is based on
kernel s/w idle stats instead).
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPwHYJAAoJEIwa5zzehBx3PugP/2Wd6HN030iO5EhFBcBcrh5T
WaJ4KfzK3tWev5QA3idvenVNhk5My1HQ+PLij7BLpjNqKCKlNK0k/K9wMI5X827T
wkFFprdUcoMVrB1ZCjzwCk4/uTGWB5BMxoZ6mlBh1sZIR/yXo91t+wO971Uqr0ho
Ky1oW9uaPZ6Eja00iDLkfJfygquA5+zNb0a29q19zWnHlRkH76jtqZgfDKy9I2nq
virYZ4uhoPnY2g1JxhnaMNNC861CgfTDEtmtNjgeEbA6t9bbjqsZoQRhcYHZP4OM
a4Iu8FOyIvAAzQzUglfAZ4Ar4uYTmVRnG39XFh4wK/8tJYt0hEQwFS26B0pYKx/5
F76bwc4SqO7H9AWBF0WhyUbny5XmJcNwJjobm/oCeAvemTi3xA6BbubyfKMHPoIr
dDSEqcAcMt9G6sS48h3Pm0caEYDVzxf202vdylz1JABiJZi1W/7v+NMdhujfotJh
7IGehNRu0foPEsRIS9wsvD2TzSdQtDdjyFkGHd83XMc3JpvwmyePO6ynbbxrVnJJ
HzlPnbLIk3VyqyVCqVXj21NKEY1dbsYPItketAwwzc1BUGcld0qvQY/t/UI4JQT6
9vq77AwNjUhfomDdEWTp7aNx0whkY0R5KEY9jHjuu9WoE+xdPZbQKm589AJ6LA4U
j6HPMzWKUHOKT6g10rCl
=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or unrealistic
configurations. Instead we queue them up to be picked up in the next
merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yCUM
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Olof Johansson:
"These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or
unrealistic configurations. Instead we queue them up to be picked up
in the next merge window."
Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: spear6xx: remove board selection options
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
arm: davinci: use for_each_set_bit_from
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: davinci: da850-evm: fix section mismatch
ARM: tegra: add pll_x freq table entry for 750MHz
ARM: davinci: mark spi_board_info arguments as const
ARM: davinci: fix incorrect pdctl next bit position
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
Pull core ARM updates from Russell King:
"This is the bulk of the core ARM updates for this merge window.
Included in here is a different way to handle the VIVT cache flushing
on context switch, which should allow scheduler folk to remove a
special case in their core code.
We have architectured timer support here, which is a set of timers
specified by the ARM architecture for future SoCs. So we should see
less variability in timer design going forward.
The last big thing here is my cleanup to the way we handle PCI across
ARM, fixing some oddities in some platforms which hadn't realised
there was a way to deal with their private data already built in to
our PCI backend.
I've also removed support for the ARMv3 architecture; it hasn't worked
properly for years so it seems pointless to keep it around."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (47 commits)
ARM: PCI: remove per-pci_hw list of buses
ARM: PCI: dove/kirkwood/mv78xx0: use sys->private_data
ARM: PCI: provide a default bus scan implementation
ARM: PCI: get rid of pci_std_swizzle()
ARM: PCI: versatile: fix PCI interrupt setup
ARM: PCI: integrator: use common PCI swizzle
ARM: 7416/1: LPAE: Remove unused L_PTE_(BUFFERABLE|CACHEABLE) macros
ARM: 7415/1: vfp: convert printk's to pr_*'s
ARM: decompressor: avoid speculative prefetch from non-RAM areas
ARM: Remove ARMv3 support from decompressor
ARM: 7413/1: move read_{boot,persistent}_clock to the architecture level
ARM: Remove support for ARMv3 ARM610 and ARM710 CPUs
ARM: 7363/1: DEBUG_LL: limit early mapping to the minimum
ARM: 7391/1: versatile: add some auxdata for device trees
ARM: 7389/2: plat-versatile: modernize FPGA IRQ controller
AMBA: get rid of last two uses of NO_IRQ
ARM: 7408/1: cacheflush: return error to userspace when flushing syscall fails
ARM: 7409/1: Do not call flush_cache_user_range with mmap_sem held
ARM: 7404/1: cmpxchg64: use atomic64 and local64 routines for cmpxchg64
ARM: 7347/1: SCU: use cpu_logical_map for per-CPU low power mode
...
flowctrl_write_cpu_csr uses the cpu halt offsets and vice versa. This patch
fixes this bug.
Reported-by: Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[swarren: This problem was introduced in v3.4-rc1, in commit 26fe681 "ARM:
tegra: functions to access the flowcontroller", when this file was first
added]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most PCI implementations use the standard PCI swizzle function, which
handles the well defined behaviour of PCI-to-PCI bridges which can be
found on cards (eg, four port ethernet cards.)
Rather than having almost every platform specify the standard swizzle
function, make this the default when no swizzle function is supplied.
Therefore, a swizzle function only needs to be provided when there is
something exceptional which needs to be handled.
This gets rid of the swizzle initializer from 47 files, and leaves us
with just two platforms specifying a swizzle function: ARM Integrator
and Chalice CATS.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By Stephen Warren
via Stephen Warren
* 'for-3.5/debug' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: uncompress.h: Implement TEGRA_DEBUG_UART_AUTO_ODMDATA
By Stephen Warren (5) and Peter De Schrijver (1)
via Stephen Warren
* 'for-3.5/tegra30-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
ARM: tegra: set up audio clocks for tegra30 dt
ARM: tegra: Initialize pll_p_out1
ARM: tegra: provide clock aliases for AHUB configlink
Signed-off-by: Olof Johansson <olof@lixom.net>
Add extern func, "tegra_ahb_enable_smmu()" to inform AHB that SMMU is
ready.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra AHB Bus conforms to the AMBA Specification (Rev 2.0) Advanced
High-performance Bus (AHB) architecture.
The AHB Arbiter controls AHB bus master arbitration. This effectively
forms a second level of arbitration for access to the memory
controller through the AHB Slave Memory device. The AHB pre-fetch
logic can be configured to enhance performance for devices doing
sequential access. Each AHB master is assigned to either the high or
low priority bin. Both Tegra20/30 have this AHB bus.
Some of configuration params could be passed from DT too if needed.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
At the moment, read_persistent_clock is implemented at the
platform level, which makes it impossible to compile these
platforms in a single kernel.
Implement these two functions at the architecture level, and
provide a thin registration interface for both read_boot_clock
and read_persistent_clock. The two affected platforms (OMAP and
Tegra) are converted at the same time.
Reported-by: Jeff Ohlstein <johlstei@codeaurora.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SKUs limit the maximum CPU frequency to 750MHz; see
tegra2_pllx_clk_init(). The pll_x frequency table needs an entry for this
frequency, or there will be continual log spam from the cpufreq driver
attempting to set this rate, yet there being no table entry for it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Not all boards use GPIO_PV0 as the ULPI PHY reset signal. Instead of
hard-coding this GPIO into devices.c, make the board files set it
explicitly. This will allow the PHY code to differentiate between set and
unset values, and hence know when to read the value from device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 is used on all/most Tegra boards to drive the cdev2 output pin
to provide a reference clock to a ULPI USB PHY. This reference clock must
run at 24MHz, and the cdev2 output has no additional dividers.
Remove board-paz00.c's now-duplicate initialization of this clock.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 40f9cf0 "ARM: tegra: reparent sclk to pll_c_out1" changed the
rate of hclk. Since pclk is derived from that, and only has integer
dividers, the pclk rate needs to change in the same fashion, from 54MHz
to 60MHz.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 needs to be used for other purposes. Reparent sclk so that
it runs from pll_c. Change sclk's rate to 120MHz from 108MHz since this
is the lowest precise rate that can be achieved by dividing the pll_c
rate without reducing the sclk rate. (600/5=120, 600/5.5=109.0909...,
600/6=100).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_c will be used as a clock source. Fill in tegra_pll_c_freq_table[]
so that it's possible to explicitly initialize the PLL.
NVIDIA's downstream nv-3.1 kernel and the ChromeOS kernel have different
pll_c tables. nv-3.1 contains entries for 522MHz and 598MHz output,
whereas the ChromeOS kernel contains entries for 600MHz output. I chose
to upstream the ChromeOS values for now, since the 600MHz rate appears
to match the default rate of this PLL when the HW boots, and it's not
clear to me why 522 or 598MHz are more useful.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: wrote commit description]
Both the Tegra30 I2S and AHUB modules used clocks, and hence currently
require AUXDATA in order to get specific device names so that clock
lookups work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Set up the audio clock tree for Tegra30 in an equivalent fashion to the
existing setup for Tegra20.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
pll_a uses pll_p_out1 as its parent. Therefore this clock needs to be
initialized to make sure pll_a has a known input clock. Failure to do so
will cause the system to crash early in the bootup.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra30 AHUB driver must call tegra_periph_reset_deassert() for all
devices on the AHUB's configlink bus. The AHUB driver must be able to
call clk_get_sys() to retrieve the clock parameter for this function.
Add the necessary clock aliases to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
The "KT" serial port has another use case for a "received break" quirk,
so before adding another special case to the 8250 core take this
opportunity to push such quirks out of the core and into a uart_port op.
Stephen says:
"If the callback function is to no longer live in 8250.c itself,
arch/arm/mach-tegra/devices.c isn't logically a good place to put it,
and that file will be going away once we get rid of all the board files
and move solely to device tree."
...so since 8250_pci.c houses all the quirks for pci serial devices this
quirk is similarly housed in of_serial.c. Once the open firmware
conversion completes the infrastructure details
(include/linux/of_serial.h, and the export) can all be removed to make
this self contained to of_serial.c.
Cc: Nhan H Mai <nhan.h.mai@intel.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
[stephen: kill CONFIG_SERIAL_TEGRA in favor just using CONFIG_ARCH_TEGRA]
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.
This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This adds a complete pinmux configuration to all Tegra20 device tree
files. This allows removal of board-dt-tegra20.c's use of the pinmux
board files, and the special device tree handling in board-pinmux.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
The pinctrl driver is now active and used by all boards. Remove the
old pinmux driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
* Rename old pinmux and new pinctrl platform driver and DT match table
entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
in pinctrl format.
Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.
All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.
Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.
Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Don't call gpio_request() or gpio_direction_input() for ISL29018_IRQ.
This pin is only used as an IRQ, and hence no GPIO configuration should
be necessary; the GPIO/IRQ driver should (and does) perform any required
setup when the IRQ is requested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Instead of having board files manually request and initialize USB VBUS
GPIOs, fill in the USB driver's platform data and have it do it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Add a vbus_gpio field to platform data. This mirrors the device tree
property nvidia,vbus-gpio. This makes the VBUS GPIO handling identical
between booting with board files and device tree; the driver always does
it.
This removes the need for board files to request and initialize the GPIO
early during their boot process, perhaps even before the GPIO driver is
ready to process the request.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
The declarations are actually required for the device
definitions, and are still valid even if the dma controller
is disabled:
arch/arm/mach-tegra/devices.c:559:12: error: 'TEGRA_DMA_REQ_SEL_I2S_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:577:12: error: 'TEGRA_DMA_REQ_SEL_I2S2_1' undeclared here (not in a function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
arch/arm/mach-tegra/board-dt-tegra20.c: included 'asm/hardware/gic.h'
twice remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
[swarren: rewrote commit subject]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra has 5 UARTS which could be used for low-level debug output. Commit
fe26398 "ARM: tegra: uncompress.h: Choose a UART at runtime" implemented
one method for the kernel to automatically determine which of these to
use at run-time, so that the same DEBUG_LL-enabled kernel image could be
used across multiple Tegra boards. The required bootloader-side setup for
that option is implemented in NVIDIA's various downstream U-Boot branches,
but the U-Boot maintainers have refused to accept it upstream.
This change implements an alternative automatic UART selection option
using ODMDATA. This is a 32-bit value programmed into Tegra's boot memory
which provides a few pieces of basic board-specific information, including
a field that indicates the console UART. Setting up this value is part of
the standard Tegra boot architecture, and so requires no Tegra-specific
hacks in the bootloader's UART driver.
Note that in theory, the format of ODMDATA is board-specific. However, in
practice all boards use the same location/size/values for the UART field.
ODMDATA[19:18] (which drive the type of debug console) is more problematic,
since some boards use value 2 for UART and others use 3. This patch just
accepts either value; if this doesn't work well for a given board, I'd
suggest simply not enabling this debug option when building for that board.
Note that the kernel assumes the bootloader has already set up any required
pinmux settings for the UART; there is no way the kernel can do this for
itself prior to knowing which board it's running on. In practice, people
using this feature are highly likely to be using bootloaders that have
indeed configured the pinmux. This assumption existed prior to this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Rename Tegra20-specific Kconfig variables, module filenames, all internal
symbol names, clocks, and platform devices, to reflect the fact the DAS
and I2S drivers are for a specific HW version.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tegra_pcm_device is no longer needed now that the Tegra ASoC code has
cleaned up its 'platform' registration. Remove it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a first pass of some of the merge window fallout for ARM platforms.
Nothing controversial:
* A system.h fallout fix for OMAP
* PXA fixes for breakage caused by the regulator struct changes
* GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
* A mismerge in our arm-soc tree of an lpc32xx change for networking
* A fix for USB setup on tegra
* An undo of __init annotation of display mux setup on OMAP that's needed
at runtime
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=36Eb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Olof Johansson:
"This is a first pass of some of the merge window fallout for ARM
platforms.
Nothing controversial:
- A system.h fallout fix for OMAP
- PXA fixes for breakage caused by the regulator struct changes
- GPIO fixes for OMAP to properly deal with dynamic IRQ allocation
- A mismerge in our arm-soc tree of an lpc32xx change for networking
- A fix for USB setup on tegra
- An undo of __init annotation of display mux setup on OMAP that's
needed at runtime"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix build issue on stargate2
ARM: pxa: fix build issue on cm-x300
ARM: pxa: fix build failure for regulator consumer in em-x270.c
ARM: LPC32xx: clock.c: Fix lpc-eth clock reference
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: pxa: fix regulator related build fail in magician_defconfig
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
ARM: OMAP2+: Remove __init from DSI mux functions
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
* 'for-3.4/fixes-for-rc1-and-v3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Fix device tree AUXDATA for USB/EHCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPcpwnAAoJEIwa5zzehBx3RIQP/AvTVHF7EIXfu5XGLBYeKW+U
HBeT1kO1qL8m3gA/+DG/JzNpd8JDlILGob6hUN4lqA8f49MBkmttdbATZvBj4Nx+
T4+louPteiueexJdolj6hVCuNBhFJLgik3zMKGHvL8wbvqYHKpfqvuWWuzxtP3Hl
F1BvFSrQ5TZALGtNiRWDMwxFa2oA03ZNXjy+v9i3GIdn1vH18/IDryz7/7MW6GPv
NuKmZkcEpX2jDFe3AkqUMLxqMYizfuGg20FlV4tmxiF5Wlht6EiN38Y56LZgwuly
mde6AWN8qgwTYDk4cJ5ZVJtwkowosF5ko57V3SPmVaVc/WajZ0v28gt9YgNLVPL7
TXFEUJgIxzJnyM+DoSltzQ9tCsWUscQGmyPt4QSOLO2D76/3z+8+24/EwAIM/7Bj
u5/+74k5jDBZe1suCt/1P1Vr3l5Z3os483R7y4BtyLtWtQvBcjpkITj9lHmnsAf3
RqN2Z4osLcILwWVKa2y2DCOeJm0jvSCsn53+O3FGTSqhfwWTUVkqaDALeGXwJGbH
2rMks18BqJ2sT2ruFXHiVvZOj/8XxkcLsq8ztnuYoHQssrNtAtBM97l/xi1V7L0z
FmXnPszVA1mIkelsY2VDImEks/Iaad4o3Iuba9Yr3OKOSr/d8kLyB0reTmS/SHQL
u/o8ch/V5QVEo/H+ud7K
=X89H
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More SoC support updates" from Olof Johansson:
"This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs"
Fix up trivial merge conflicts as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: mach-shmobile: ap4evb: Reserve DMA memory for the frame buffer
ARM: EXYNOS: Fix compilation error with mach-exynos4-dt board
ARM: dts: add initial dts file for EXYNOS5250, SMDK5250
ARM: EXYNOS: add support device tree enabled board file for EXYNOS5
ARM: EXYNOS: add support ARCH_EXYNOS5 for EXYNOS5 SoCs
ARM: EXYNOS: add support get_core_count() for EXYNOS5250
ARM: EXYNOS: support EINT for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add interrupt definitions for EXYNOS5250
ARM: EXYNOS: add support for EXYNOS5250 SoC
ARM: EXYNOS: add support uart for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add initial setup-i2c0 for EXYNOS5
ARM: EXYNOS: add clock part for EXYNOS5250 SoC
ARM: EXYNOS: use exynos_init_uarts() instead of exynos4_init_uarts()
ARM: EXYNOS: to declare static for mach-exynos/common.c
ARM: EXYNOS: Add clkdev lookup entry for lcd clock
ARM: dt: Explicitly configure all serial ports on Tegra Cardhu
ARM: tegra: support for secondary cores on Tegra30
ARM: tegra: support for Tegra30 CPU powerdomains
ARM: tegra: add support for Tegra30 powerdomains
ARM: tegra: export tegra_powergate_is_powered()
...
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
Avoid namespace conflicts with drivers over the CP15 definitions by
moving CP15 related prototypes and definitions to a private header
file.
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com> [Tegra]
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> [EP93xx]
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
* 'for-3.4/fixes-for-io-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Include assembler.h in sleep.S to fix build break
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
These changes are all specific to an soc family or the code for
one soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later in
the merge window for stuff that has dependencies on external trees or
that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly because
of changes regarding localtimer.c, which was removed in the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WdYR
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC specific updates" from Arnd Bergmann:
"These changes are all specific to an soc family or the code for one
soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later
in the merge window for stuff that has dependencies on external trees
or that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly
because of changes regarding localtimer.c, which was removed in the
end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up some trivial conflicts, including the mentioned Tegra Makefile.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
...
These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree
based booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=z4Mj
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: timer cleanup work" from Arnd Bergmann:
"These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree based
booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
ARM: tegra: select USB_ULPI if USB is selected
arm/tegra: pcie: fix return value of function
ARM: ux500: fix compilation after local timer rework
ARM: shmobile: remove additional __io() macro use
ARM: local timers: make the runtime registration interface mandatory
ARM: local timers: convert MSM to runtime registration interface
ARM: local timers: convert exynos to runtime registration interface
ARM: smp_twd: remove old local timer interface
ARM: imx6q: convert to twd_local_timer_register() interface
ARM: highbank: convert to twd_local_timer_register() interface
ARM: ux500: convert to twd_local_timer_register() interface
ARM: shmobile: convert to twd_local_timer_register() interface
ARM: tegra: convert to twd_local_timer_register() interface
ARM: plat-versatile: convert to twd_local_timer_register() interface
ARM: OMAP4: convert to twd_local_timer_register() interface
ARM: smp_twd: add device tree support
ARM: smp_twd: add runtime registration support
ARM: local timers: introduce a new registration interface
ARM: smp_twd: make local_timer_stop a symbol instead of a #define
ARM: mach-shmobile: default to no earlytimer
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Commit 6f6f6a7 "ARM: create a common IOMEM definition" moved macro
IOMEM(), and requires users to include <asm/assembler.h>. Fix Tegra's
sleep.S to do so. This fixes:
arch/arm/mach-tegra/sleep.S: Assembler messages:
arch/arm/mach-tegra/sleep.S:77: Error: missing ')'
arch/arm/mach-tegra/sleep.S:77: Error: garbage following instruction
-- `movw r0,#:lower16:(0x60007000-0x60000000+IOMEM(0xFE200000))'
Note: This only shows up after 0a25893 "ARM: tegra: update defconfig"
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
they contain two new IOMMU drivers for the ARM Tegra 2 and 3 platforms.
Besides that there are also a few patches for the AMD IOMMU which
prepare the driver for adding intr-remapping support and a couple of
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lCBm
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The IOMMU updates for this round are not very large patch-wise. But
they contain two new IOMMU drivers for the ARM Tegra 2 and 3
platforms. Besides that there are also a few patches for the AMD
IOMMU which prepare the driver for adding intr-remapping support and a
couple of fixes."
* tag 'iommu-updates-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix section mismatch
iommu/amd: Move interrupt setup code into seperate function
iommu/amd: Make sure IOMMU interrupts are re-enabled on resume
iommu/amd: Fix section warning for prealloc_protection_domains
iommu/amd: Don't initialize IOMMUv2 resources when not required
iommu/amd: Update git-tree in MAINTAINERS
iommu/tegra-gart: fix spin_unlock in map failure path
iommu/amd: Fix double free of mem-region in error-path
iommu/amd: Split amd_iommu_init function
ARM: IOMMU: Tegra30: Add iommu_ops for SMMU driver
ARM: IOMMU: Tegra20: Add iommu_ops for GART driver
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPazYTAAoJEEEQszewGV1z09IQAIcsnFO5s7XfvfXhwNCliiKp
myVMJdYcx8GSOg5Oif9uektcBi0gB2ppegxVYDxDq8FZqZQ4d3pYDZel3tDBGKJI
9ZXemh1iIeXwLZBXSENxn0NZokAZVDiyBqi50zsINV+riFfyzL9Ai7o3YkEx9xBG
nJ6S9wthzeF2qF8/NBvMYgCefZXIKJ8miwVrb9MusWUBfeAY7F8jVNlK9Asp9ruv
XEC+WcrWRttB/8+5z3FkPPtEnJ+0Y2p6e6+hn8Cel0UWb4+WDijumO+hTyIiNYSc
ryzFMqX18L8taaDhxQZ1kRDL5S7Qu7N3HYu+4wBvPI3D81MroS5frJbUwPcD8WsK
Pw/NZtAwJhp4B9/LVOOoAyBoRTfeIwrbp+ou2zF5m70hpBD5D1mN/2xVBBQgjm9T
oY9jNoJ2PhZP74fO4jdf4iMW1j5ZmzwxLXlpT3vGJeONIUg2hE0FJjzoeOjRsUtO
iC0m7Q1AbJpIcjJlcK+gV/ZclaOWy4iDXDXFs4A3XA+ryf/ylDL5G+c/1Qu6CMyF
4AhKs78Fg7agtVYX/QYuie9BbasRjipxiPc0t3/46Abs7WRzvpmBWWktFE4yy980
93jLyog0VROHIOl974Fn0GrNJeNUTavc5DEd32zlc7AiAibOzyuRztwJ5GZbuZAN
SE0VyQBIIdkaF51XV+IO
=Gg7v
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
Commit 4a53f4e "USB: ehci-tegra: add probing through device tree" added
AUXDATA for Tegra's USB/EHCI controller. However, it pointed the platform
data at a location containing the address of the intended platform data,
rather than the platform data itself. This change fixes that.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: <stable@vger.kernel.org> # 3.3
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-vexpress/core.h
The tegra Makefile was changed in four different branches
in the same line. This merge should reduce the amount
of churn.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-3.4/cleanup-and-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: select USB_ULPI if USB is selected
arm/tegra: pcie: fix return value of function
arm/tegra: add timeout to PCIe PLL lock detection loop
arm/tegra: fix harmony pinmux for PCIe
Automatically select USB_ULPI if USB is enabled on Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In previous patch (arm/tegra: add timeout to PCIe PLL lock detection loop)
tegra_pcie_enable_controller() function type has been changed from
void to int, but the last return statement wasn't converted, so
function returns undefined value. Fix it.
Also while at it, address couple of minor concerns raised by reviewers:
use usleep_range for delay, and lower the value of timeout to 300ms
to be consistent with Nvidia Vibrante kernel.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/common.c
arch/arm/mach-ux500/devices-common.c
This resolves two conflicts and lets us merge the exynos5 branch
cleanly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Several platforms create IOMEM defines for casting to 'void __iomem *',
and other platforms are incorrectly using __io() macro for the same
purpose. This creates a common definition and removes all the platform
specific versions. Rather than try to make linux/io.h and asm/io.h
assembly safe, the assembly version of IOMEM is moved into
asm/assembler.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for the new smp_twd runtime registration interface
to the tegra platforms, and remove the old compile-time support.
Tested on Harmony.
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tegra PCIe driver waits for PLL to lock using busy loop.
If PLL fails to lock for some reason, this leads to silent lockup
while booting (as PCIe code is not modular).
Fix by adding timeout, so if PLL doesn't lock in a couple
of seconds, just PCIe driver fails and machine continues to boot.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 6e96aca397 (arm/tegra: Harmony PCIe: Don't touch pinmux)
removed runtime tri-state toggling for PCIe related pinmux groups,
but it seems that the fact that all of them are tri-state by default
has been overlooked. Change defaults for these groups to TEGRA_TRI_NORMAL.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
__mem_pci is only used to enable readl/writel and friends. Just condition
this on readl being defined and remove all the __mem_pci defines.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Move tegra specific mach/io.h parts into iomap.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
This causes the Tegra pinctrl driver to be built whenever core Tegra
support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra pinmux, and required parameterization
data for Tegra20 and Tegra30.
The driver is initially added with driver name and device tree compatible
value that won't cause this driver to be used. A later change will switch
the pinctrl driver to use the correct values, switch the old pinmux
driver to be disabled, and update all code that uses the old pinmux APIs
to use the new pinctrl APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
[squashed "fix case of Tegra30's foo_groups[] arrays"]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.
* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: match SoC name not board name in DT board files
ARM: tegra: PCIe: Provide 3.3V supply voltage
ARM: dt: tegra: add the wifi led to paz00 device tree
ARM: dt: tegra: add the power gpio key to paz00 device tree
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From: Olof Johansson <olof@lixom.net>
SoC new development for tegra SoCs, mostly tegra30 core support.
It also includes one stray bugfix that was misapplied (should have been
in soc-drivers), but it went out to the stable branches before I noticed
so I've left it in.
* tag 'tegra-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
ARM: tegra: Avoid compiling cpuidle code when not configured
ARM: tegra: cpuidle driver for tegra
ARM: tegra: assembler code for LP3
ARM: tegra: definitions for flow controller
ARM: tegra: initialize basic system clocks
ARM: tegra: enable tegra30 clock framework
ARM: tegra: implement basic tegra30 clock framework
ARM: tegra: add support for new clock framework features
ARM: tegra: add support for tegra30 interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes that weren't urgent enough to go into 3.3. The two paz00
patches are in mainline already but got merged after the branch point
for this branch, so they're duplicated. I also ended up merging in
rmk/for-armsoc into this later on to fix a bug introduced by it, so it's
included but it's not the base of this branch.
* tag 'tegra-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Enable CPUIdle on Tegra20
ARM: tegra: export usb phy symbols
ARM: tegra: build localtimer support only when needed
ARM: tegra: select CPU_FREQ_TABLE
ARM: tegra: select required CPU and L2 errata options
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes that weren't urgent enough to go into 3.3. The two paz00
patches are in mainline already but got merged after the branch point
for this branch, so they're duplicated. I also ended up merging in
rmk/for-armsoc into this later on to fix a bug introduced by it, so it's
included but it's not the base of this branch.
* tag 'tegra-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Enable CPUIdle on Tegra20
ARM: tegra: export usb phy symbols
ARM: tegra: build localtimer support only when needed
ARM: tegra: select CPU_FREQ_TABLE
ARM: tegra: select required CPU and L2 errata options
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the LP3 code also works for Tegra20, we can enable cpuidle for Tegra20.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ehci driver can be a module, so the functions provided
by the tegra platform code used by ehci-tegra need to
be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
It is possible to build a tegra kernel without localtimer
support, so the tegra specific parts should only be built
when that is indeed enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
The tegra cpufreq implementation relies on the cpu_freq_table
code, so make sure that this is always there when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected
The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.
For now, only enable UART1/A, and explicitly disable all other ports.
The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.
Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.
While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
board-dt-tegra*.c should support any board using Tegra when booted using
device tree. Instead of explicitly listing all the supported boards,
which requires a kernel change for each new board, list the supported SoC
model instead.
Note that the board files do currently have explicit support for setting
up each board's pinmux. However, it's fairly likely that at least the
basic devices on any new board will work just fine as set up by the boot-
loader, and the pinmux data should be moving into device tree soon anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes the following compile error:
CC arch/arm/boot/compressed/misc.o
In file included from arch/arm/boot/compressed/misc.c:28:0:
arch/arm/mach-tegra/include/mach/uncompress.h: In function 'arch_decomp_setup':
arch/arm/mach-tegra/include/mach/uncompress.h:125:2: error: implicit declaration of function 'BUILD_BUG_ON_ZERO' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
This is due to use of the ARRAY_SIZE() macro. Typically, this would be
solved by including <linux/bug.h>, but the compressor code isn't part of
the kernel, and so should not include kernel headers. Instead, define
the few macros the code uses directly, and in a way that doesn't depend
on <linux/bug.h>.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for bringing up secondary cores on Tegra30. On Tegra30 secondary
CPU cores are powergated, so we need to turn on the domains before we can bring
the CPU cores online. Bringing secondary cores online happens early during the
sytem boot, so we call powergating initialization from platform early_init
function.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Colin Cross <ccross@android.com>
Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Secondary CPU powerdomains can be powergated on Tegra30. Add the necessary
functions to do this. This will be used to boot the secondary CPUs later on.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the new powerdomains in Tegra30 such as extra CPU cores and
the SATA domain.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Export tegra_powergate_is_powered(). This function will be used by the Tegra30
code to bringup secondary CPU cores.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prepare the powergating code for other Tegra variants which have a different
number of powerdomains.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prepare the Tegra secondary CPU core bringup code for other Tegra variants.
The reset handler is also generalized to allow for future introduction of
powersaving modes which turn off the CPU cores.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Chris Johnson <cwj@nvidia.com>
Colin Cross <ccross@android.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce some functions to write to the flowcontroller registers. The
flowcontroller controls CPU sleepstates and wakeup.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Secondary core bringup relies on the Tegra chipid to distinguish between
Tegra variants. Therefore this data needs to be available early on.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The powergating and reset handling code needs to differentiate between Tegra
variants. Therefore we export the chipid here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The chipid register contains information about the Tegra variant and revision.
We want differentiate between Tegra variants for powergating and secondary
core bringup. This patch cleans up the reading and decoding of this register.
In subsequent patches the variant will exported as a global variable.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PCIe reference clock needs a 3.3V supply voltage to work properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ARM IP revisions in Tegra are:
Tegra20: CPU r1p1, PL310 r2p0
Tegra30: CPU A01=r2p7/>=A02=r2p9, NEON r2p3-50, PL310 r3p1-50
Based on work by Olof Johansson, although the actual list of errata is
somewhat different here, since I added a bunch more and removed one PL310
erratum that doesn't seem applicable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
When this inconsistency occurs, the system will typically operate without
issue, it's just that EMC scaling won't optimally. Convert the BUG_ON to
a WARN_ONCE in order to allow the kernel to boot, but still complain.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
No need to compile cpuidle.c and sleep.S if cpuidle isn't configured in the
kernel.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The new PMC driver now configures the PMU interrupt inversion, so board
files don't need to poke the PMC registers directly to achieve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
UARTC is connected to the mini-pcie port.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This PMC driver is enough to parse the nvidia,invert-interrupt property
from device tree, and configure the PMC's to honor that.
In the future, this file could expand to centralize all other PMC accesses
within the mach-tegra code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
It is not require to move the requestor of dma to INVALID
option before stopping dma.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit d91eeb0 "ARM: tegra: emc: device tree support" modified the EMC
driver to create an EMC table from existing register settings when none
was provided through platform data or device tree. This code wrote the
wrong clock rate into the table; the actual rate in Hz, rather than the
expected half-rate in KHz. This caused the BUG_ON in
tegra2_emc_clk_round_rate() to fire, since that enormous rate could not
be generated.
Fixes:
[ 2.425921] kernel BUG at arch/arm/mach-tegra/tegra2_clocks.c:1158!
...
[ 2.618766] [<c001c0e8>] (tegra2_emc_clk_round_rate+0x58/0x70) from [<c00198b4>] (clk_round_rate+0x48/0x68)
[ 2.628494] [<c00198b4>] (clk_round_rate+0x48/0x68) from [<c0019cc0>] (clk_set_rate_locked+0x40/0x68)
[ 2.637707] [<c0019cc0>] (clk_set_rate_locked+0x40/0x68) from [<c0019d10>] (clk_set_rate+0x28/0x40)
[ 2.646754] [<c0019d10>] (clk_set_rate+0x28/0x40) from [<c001ffc8>] (tegra_update_cpu_speed+0x54/0x144)
[ 2.656144] [<c001ffc8>] (tegra_update_cpu_speed+0x54/0x144) from [<c002016c>] (tegra_target+0xb4/0xe0)
[ 2.665538] [<c002016c>] (tegra_target+0xb4/0xe0) from [<c01a96c0>] (__cpufreq_driver_target+0x88/0xa4)
[ 2.674931] [<c01a96c0>] (__cpufreq_driver_target+0x88/0xa4) from [<c01ac9d0>] (dbs_check_cpu+0x324/0x340)
[ 2.684582] [<c01ac9d0>] (dbs_check_cpu+0x324/0x340) from [<c01aca40>] (do_dbs_timer+0x54/0xf4)
[ 2.693277] [<c01aca40>] (do_dbs_timer+0x54/0xf4) from [<c00369a8>] (process_one_work+0x1d4/0x320)
[ 2.702225] [<c00369a8>] (process_one_work+0x1d4/0x320) from [<c0036f34>] (worker_thread+0x134/0x230)
[ 2.711437] [<c0036f34>] (worker_thread+0x134/0x230) from [<c003add0>] (kthread+0x80/0x8c)
[ 2.719700] [<c003add0>] (kthread+0x80/0x8c) from [<c000ebf4>] (kernel_thread_exit+0x0/0x8)
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[olof: fixed calculation of printed values]
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace compile-time usage of TEGRA_GPIO_TO_IRQ with run-time calls to
gpio_to_irq(). This will allow the base IRQ number for the Tegra GPIO
driver to be dynamically allocated in a later patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
uncompress.h now saves the selected UART's physical address in Tegra's
IRAM, along with a cookie to indicate validity.
The first time it's run, macro addruart in debug-macro.S looks for this
cookie, and if it's present, uses the UART address stored there. If not,
the static value TEGRA_DEBUG_UART_BASE is used, as was previous behaviour.
The static behaviour will thus be used when not booting using a zImage.
This work was inspired by work by Doug Anderson <dianders@chromium.org>;
see http://lkml.org/lkml/2011/9/26/284. However, this patch relies on
the data passing describe above, rather than duplicating the UART
selection logic in debug-macro.S; the latest selection logic is more
complex due to the need to check reset/clock bits too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
With this change we automatically detect which UART to use for
for printing during decompression. The detection involves coordination
with the bootloader: it's expected that the bootloader will leave a
'D' (for [D]ebug) in the UART scratchpad register for whichever UART we
should use for debugging.
If we don't find any such UART, we fall back to the UART that was
specified during config time: CONFIG_TEGRA_DEBUG_UART_XXX.
As a side effect of this change, uncompress debug messages will work
if you've specified CONFIG_TEGRA_DEBUG_UART_NONE, provided the
bootloader obeys the protocol.
This change is in line with what is documented in
Documentation/arm/Booting.
Other approaches considered:
* Hardcode based on machine ID (as many other ARM boards do).
OK, but nice to not have yet another place to add per-board
code. Better to have bootloader parse device tree and pass us
this info.
* Check for TXE bit (like SA1110). Nice (and doesn't require
a bootloader change), but a little less explicit. Also: if
bootloader (for some reason) uses another UART, it needs to
remember to turn it off before jumping to the kernel or we may
print to it. NOTE: adapting this patch to check TXE too would
be easy if desired.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Added clock/reset condition checks]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will allow a future change to auto-detect which UART to use.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Extracted from a larger patch by Doug]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the need for the variable "shift" in all functions in
uncompress.h.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Extracted from a larger patch by Doug]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
On Tegra20, the UART clock runs at 216MHz, whereas on Tegra30 it runs at
408MHz. Modify arch_decomp_setup() to detect Tegra20-vs-Tegra30 at run-
time, and program the correct divisor.
This makes uncompressor messages work correctly on Tegra30. This also
fixes early printk, assuming zImage is used and this setup code runs.
v2: Use CHIPID register to differentiate between chips, rather than a
GIC register. This should be more future-proof. Volatile is required
to prevent the compiler transforming the 32-bit apb_misc register read
into an 8-bit read of address 1 higher, since the HW only supports 32-
bit accesses, and will hang on an 8-bit access.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to read an accurate channel transfer count
from the APB DMA engine, the DMA controller must be
paused first.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device tree support to the emc driver, filling in the platform data
based on the DT bindings.
Changes since v1:
* Unmangled some messed up patch squashes, moving changes to earlier patches
* Flipped an of_property_read_u32 return value test
* Clarified clock settings message on case where no table is provided
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This is the first step in making it device-tree aware and get rid of the
in-kernel EMC tables (of which there are none in mainline, thankfully).
Changes since v3:
* moved to devm_request_and_ioremap() in probe()
Changes since v2:
* D'oh -- missed a couple of variables that were added, never used and then
later removed in a later patch.
Changes since v1:
* Fixed messed up indentation
* Removed code that should be gone (was added here and removed later in series)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add function to get chip revision, and print it out at boot time.
Restructure the fuse access to just use cached variables instead
of always reading the fuses, and export those variables directly
instead of using accessor functions.
Add a SKU ID table of currently known values.
Based on code originally by Colin Cross <ccross@android.com>.
Changes since v1:
* Add A01 minor rev support
* Don't decode for A03p on anything but T2x
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tegra2 hangs if APB registers are accessed from the cpu during an
apb dma operation. The workaround is to use apb dma to read/write the
registers instead.
There is a dependency loop between fuses, clocks, and APBDMA. If dma
is enabled, fuse reads must go through APBDMA to avoid corruption due
to a hw bug. APBDMA requires a clock to be enabled. Clocks must read
a fuse to determine allowable cpu frequencies.
Separate out the fuse DMA initialization, and allow the fuse read
and write functions to be called without using DMA before the DMA
initialization has been completed. Access to the fuses before APBDMA
is initialized won't hit the hardware bug because nothing else can be
using DMA.
Original fuse registar access code from Varun Wadekar
<vwadekar@nvidia.com>, improved by Colin Cross <ccross@android.com>
and later moved to separate driver by Jon Mayo <jmayo@nvidia.com>.
Major refactoring/cleanup by Olof Johansson <olof@lixom.net>.
Changes since v1:
* fix 'return false' on error condition
* dequeue dma ops in case of timeout
From: Jon Mayo <jmayo@nvidia.com>.
Signed-off-by: Jon Mayo <jmayo@nvidia.com>.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Since we'll do opportunistic allocations before the dma subsystem is
enabled we want just silent failures and retries instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
CPUidle driver for tegra. In this version only LP3 (clockgating) is supported.
Based on work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Configure the flow controller for clockgating and enter WFI
Based on work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce some definitions for the tegra flow contoller. This will be
used by the code which controls entering and leaving LP3.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Initialize basic system clocks and provide a auxdata table to allow some
peripheral drivers to find their clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add init calls for clocks on tegra30.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add basic tegra30 clock framework. Not all clocks are supported yet. Mainly
clocks requiring voltage scaling are not yet implemented in this version.
Based on work by Alex Frid <afrid@nvidia.com> and
Scott Williams <scwilliams@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for new clock framework features implemented in tegra30.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra30 has 1 extra legacy interrupt controller. Use the GIC ITLinesNumber
field to determine how many interrupt controllers we have and initialize
appropriately. Also make room for the extra tegra30 interrupts by moving
the GPIO IRQ base. This shouldn't affect existing code as it determines the
correct IRQ number for GPIOs using TEGRA_GPIO_TO_IRQ().
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow marking some of GPIO pins as ignored to to avoid continuously
generating KBC input events.
Signed-off-by: Shridhar Rasal <srasal@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need to keep the DMA_REQ_SEL defines inside the ifdef.
Fixes the following build break with CONFIG_TEGRA_SYSTEM_DMA=n:
arch/arm/mach-tegra/devices.c:645: error: 'TEGRA_DMA_REQ_SEL_I2S_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: 'TEGRA_DMA_REQ_SEL_I2S2_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:663: error: (near initialization for 'i2s_resource2[1].start')
arch/arm/mach-tegra/devices.c:664: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:664: error: (near initialization for 'i2s_resource2[1].end')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add support for Tegra30 by correcting definitions. This is necessary to
make driver useful in Tegra30.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Acked-by: Stephen Warren: <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The crypto driver will need this api to use
it in the RNG calculations. In order to build
the crypto driver as a module, tegra_chip_uid
has to be exported.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Henning Heinold <heinold@inf.fu-berlin.de>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hp8k
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* samsung/dt: (3 commit)
Merge branch 'depends/rmk/for-linus' into samsung/dt
Merge branch 'depends/rmk/restart' into next/cleanup
Merge branch 'next/cleanup' into samsung/dt
Conflicts:
arch/arm/mach-tegra/board-dt.c
arch/arm/mach-tegra/include/mach/entry-macro.S
The latest version of the samsung/dt branch resolves
all sorts of conflicts with the latest upstream, no functional
changes that are not already there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-exynos/common.c
The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.
Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-tegra/board-harmony-pcie.c
To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* tegra/dt:
arm/tegra: Seaboard: Add GPIO key device tree nodes
arm/dt: Add ADT7461 to Seaboard
arm/dt: tegra: Use new compatible value for DVC I2C controller
arm/tegra: initial device tree for tegra30
arm/tegra: convert tegra20 to GIC devicetree binding
arm/dt: tegra: Fix SDHCI nodes to match board files
arm/dt: tegra: Fix serial nodes to match board files
arm/dt: tegra: Fix I2C nodes to match board files
arm/dt: tegra: Remove /chosen node
arm/dt: tegra: Remove /memreserve/ from device-tree files
arm/tegra: board-dt: Enable audio-related clocks
arm/tegra: board-dt: Fix AUXDATA typo
arm/dt: tegra: add dts file for paz00
arm/tegra: Add device-tree support for TrimSlice board
arm/dt: tegra: Clean up I2S and DAS nodes
USB: ehci-tegra: add probing through device tree
arm/dt: add basic usb nodes to tegra device trees
arm/tegra: fix variable formatting in makefile
Conflicts:
arch/arm/mach-tegra/Makefile
Arnd Bergmann