The line belongs above the comment, not below it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The CFE does not use 4K sectors even if the flash supports it, so
for the fixed partitions like CFE itself or NVRAM the erase block
size is always 64k or bigger.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The length of the spare part is calculated the same way in both branches
so move to a common place.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
namelen is never used, so drop it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
By replacing a kthread with a workqueue, the code is now a bit clearer.
There's also a slight reduction of code size (numbers apply for x86):
Before:
text data bss dec hex filename
3248 36 0 3284 cd4 drivers/mtd/mtd_blkdevs.o
After:
text data bss dec hex filename
3150 36 0 3186 c72 drivers/mtd/mtd_blkdevs.o
Due to lack of real hardware, tests have been performed on an emulated
environment with mtdswap and mtdblock over nandsim devices.
Some real testing should be done, before merging this patch.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
struct mtd_blktrans_ops is a type, and mtd_blktrans_ops is a variable.
To improve code clarity it's better to not use the same names,
so we just change the latter.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When we scan several nand chips with nand_scan(), such as
.......................
nand_scan(*, 2);
.......................
In nand_scan_ident(), the maxchips will become 2, so the current code
will select chip 1 to read the device ID. But the chip 0 is still
selected in this case.
To make the logic clear, we'd better de-select the chip when it is not used.
This patch de-select the nand chip if it is not used any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'set' is tested for NULL. But subsequently accessed without the check.
Thus making it conditional to avoid NULL pointer dereferencing.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
linux,mtd-name allow to specify the mtd name for retro capability with
physmap-flash drivers as boot loader pass the mtd partition via the old
device name physmap-flash.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Enabling the diskonchip drivers on most architectures results
in a pointless warning "#warning Unknown architecture for
DiskOnChip. No default probe locations defined". The driver
can in fact handle the default location already through the
CONFIG_MTD_DOCPROBE_ADDRESS, which gets set on the platforms
that need it, and we get a run-time error if this is not
set correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch allow to detect buggy driver/hardware with
bad RnB (dev_ready) management or when timeout occurs in polling mode.
This works when dev_ready is set or not set.
There are 2 methods to wait for an erase/program command completion:
1. Wait until nand RnB pin goes high (that's what chip->dev_ready usually does)
2. Poll the device: send a status (0x70) command and read status byte in a loop
until bit NAND_STATUS_READY is set
In all cases, you should send a status command after completion, to check if
the operation was successful. And if the operation completed, the status should
have bit NAND_STATUS_READY set.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Enhance the driver to support partition subnodes inside the nand
device bindings to describe partions on the nand device.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
When the kernel parses the following cmdline
#mtdparts=gpmi-nand:16m(boot),16m(kernel),1g(home),4g(test),-(usr)
for a big nand chip Micron MT29F64G08AFAAAWP(8GB), we got the following wrong
result:
.............................................
"mtd: partition size too small (0)"
.............................................
We can not get any partition.
The "4g(test)" partition triggers a overflow of the "size". The memparse()
returns 4g to the "size", but the size is "unsigned long" type, so a overflow
occurs, the "size" becomes zero in the end.
This patch changes the "size"/"offset" to "unsigned long long" type,
and replaces the UINT_MAX with ULLONG_MAX for macros SIZE_REMAINING and
OFFSET_CONTINUOUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The current version on mtdoops erase first block of mtdoops partition at each
boot if there is no oops stored in flash. This can wear the flash.
When mtdoops start, find_next_position is called to find the next free entry in
the circular buffer. But if the flash is erased, find_next_position don't find
anything (maxcount == 0xffffffff) and start with the first entry after erasing it.
The scanning that is done in find_next_position already track free/used entries.
So if at the end of the scanning we don't find anything, we can start at the
first entry and erased the entry only if it is marked as used.
Most of this is implemented in mtdoops_inc_counter, so to avoid duplicating
code, if we don't find anything we set position to -1. mtdoops_inc_counter with
increment it, erase the entry if needed and start as before with nextpage = 0
and nextcount = 1).
Also during the scan phase, we use the MTDOOPS_KERNMSG_MAGIC to detect corruped
entries.
Signed-off-by: Matthieu Castet <matthieu.castet@parrot@com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The code probes if DMA channels can get allocated and tears them down at
removal/failure if needed.
If available it uses them to transfer the data part (not ECC). On
failure we fall back to PIO mode.
Based on Guennadi Liakhovetski's code from the sh_mmcif driver.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes
as well.
- Change of the type of the member index in struct sh_flctl from signed
to unsigned. We use index by addressing array members, so unsigned is more
concise here. Adapt functions relying on sh_flctl::index.
- Remove a blurring cast in write_fiforeg().
- Apply consistent naming scheme when refering to the data buffer.
- Shorten some unnecessarily verbose functions.
- Remove spaces at start of lines.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The whole gpmi-nand driver has turned to pure devicetree supported.
So the linux/mtd/gpmi-nand.h is not neccessary now. Just remove it,
and move some macros to the gpmi-nand driver itself.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
In some configurations of "gpio-nand" RDY-pin may be not connected.
This patch allow to use driver for these configurations. In this case
we are assume that device always ready.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use the NAND_STATUS_FAIL to replace the hardcode "0x01",
which make the code more readable.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use pr_info() and pr_err() while defining pr_fmt(). This saves a few
characters, joins a few lines, and makes the code a little more readable
(and grep-able).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use KBUILD_MODNAME instead of hardcoding the filename
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use relaxed variants of readl/writel accessors. readl/writel io accessors use
explicit dsb instruction which causes stalls in the processor core resulting
several cycles of delay for each access
Use relaxed variants where ever possible. This also results in an improved
read/write performance.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Interruptible wait caused trouble in fsmc hardware state machine if the
application was killed abruptly. To make fsmc operation safe turn wait in to
un-interruptible.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The nomadik_nand driver is really just a subset of the FSMC
NAND driver, and there are no users anymore so let's delete
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The Denali controller can also be found in SoC devices attached to a
simple bus. Move the PCI specific parts into denali_pci so that we can
add a denali_dt that uses the same driver but for a device tree driver
instead of a PCI based device.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Since the introduction of nand_create_default_bbt_descr() (now known as
nand_create_badblock_pattern()) in
commit 58373ff0af
nand_chip.badblock_pattern will be dynamically calculated to the same
1-byte-length pattern that is required by fsl_elbc_nand. This custom
badblock_pattern is no longer needed, then, and its removal may help
facilitate further nand_bbt.c/nand_base.c cleanup in the future (one
down, many to go?)
Anyway, with nand_bbt.c fixed, this effectively reverts:
commit 452db27243
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The pointer returned by kzalloc should be tested for NULL
to avoid potential NULL pointer dereference later. Incorrect
pointer was being tested for NULL. Bug introduced by commit fbcf62a3
(mtd: physmap_of: move parse_obsolete_partitions to become separate
parser).
This patch fixes this bug.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: stable@vger.kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Simply 'parse_cmdline_partitions': the outer loop iterating over
'partitions' is actually a search loop, it does not execute the inner
loop for each partition, only for the matched partition.
Let's break when search is successful, and move all inner code (relevant
only for the matched partition) outside of the outer loop.
Resulting code is much more readable, and makes the indent level sane.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch fixes errors seen in identifying old Samsung SLC, due to the
following commits:
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with
wraparound like:
Samsung K9K8G08U0D
ec d3 51 95 58 ec ec d3
Samsung K9F1G08U0C
ec f1 00 95 40 ec ec f1
Samsung K9F2G08U0B
ec da 10 95 44 00 ec da
This bad wraparound makes it hard to reliably detect the difference
between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID.
The fix is to, for now, only use the new Samsung table for MLC. We
cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID
decode information.
Note that this applies in addition to the previous regression fix:
commit bc86cf7af2
mtd: nand: fix Samsung SLC NAND identification regression
Together, these patches completely restore the previous detection
behavior so that we cannot see any more regressions in Samsung SLC NAND
(finger crossed). With luck, I can get a hold of a Samsung
representative and stop having to cross my fingers eventually.
Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:
ec da 10 95 44 00 ec da
The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.
This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fixes the following sparse warning:
drivers/mtd/onenand/onenand_base.c:3697:5: warning:
symbol 'flexonenand_set_boundary' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This moves the MTU timer driver from arch/arm/plat-nomadik
to drivers/clocksource and moves the header file to the
platform_data directory.
As this moves the last file being compiled to an object out
of arch/arm/plat-nomadik, we have to "turn off the light"
and delete the plat-nomadik directory, because it is not
allowed to have an empty Makefile in a plat-* directory.
This is probably also a desired side effect of depopulating
the arch/arm directory of drivers. Luckily we have just
deleted all the <plat/*> include files prior to this so
by moving the last one we may delete the directory.
After this all the Ux500 and Nomadik device drivers live
outside of the arch/arm hierarchy.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b7754452b3 ("mtd: onenand: omap:
use pdata info instead of cpu_is") broke an OMAP3+4 build and an N800
multi-OMAP2xxx build here:
drivers/built-in.o: In function `omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:742: undefined reference to `omap2_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:743: undefined reference to `omap2_onenand_write_bufferram'
drivers/mtd/onenand/omap2.c:742: undefined reference to `omap2_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:743: undefined reference to `omap2_onenand_write_bufferram'
...
drivers/built-in.o: In function `omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:788: undefined reference to `omap3_onenand_read_bufferram'
drivers/mtd/onenand/omap2.c:788: undefined reference to `omap3_onenand_write_bufferram'
Fix by declaring static functions for the missing symbols, rather than
just prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Afzal Mohammed <afzal@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
UBI reserves an LEB sized buffer for various needs. We can use this buffer
while scanning, instead of allocating another one. This patch was originally
created by Jan Luebbe <jlu@pengutronix.de>, but then he dropped it and I picked
up and tweaked a little bit.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Modify the device PM QoS core code to support PM QoS flags requests.
First, add a new field of type struct pm_qos_flags called "flags"
to struct dev_pm_qos for representing the list of PM QoS flags
requests for the given device. Accordingly, add a new "type" field
to struct dev_pm_qos_request (along with an enum for representing
request types) and a new member called "flr" to its data union for
representig flags requests.
Second, modify dev_pm_qos_add_request(), dev_pm_qos_update_request(),
the internal routine apply_constraint() used by them and their
existing callers to cover flags requests as well as latency
requests. In particular, dev_pm_qos_add_request() gets a new
argument called "type" for specifying the type of a request to be
added.
Finally, introduce two routines, __dev_pm_qos_flags() and
dev_pm_qos_flags(), allowing their callers to check which PM QoS
flags have been requested for the given device (the caller is
supposed to pass the mask of flags to check as the routine's
second argument and examine its return value for the result).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc-nand bch registers are now available in driver,
make use of it to handle bch[48] instead of relying
on gpmc exported functions.
And so nand driver no longer needs gpmc header, remove it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Bring onto driver the macros defined in gpmc.h that are
not necessary outside driver, helps in removing inclusion
of gpmc.h too. Also remove GPMC prefix on those macros to
make clear it's independence with gpmc header.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
platform data now contains a field to indicate whether
soc belongs to omap34xx family, use it instead of
cpu_is_* check.
This helps in removing dependency of platform specific
header file - cpu.h
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Now that gpmc-nand registers are available in driver, use it
to read nand data.
"65b97cf mtd: nand: omap2: handle nand on gpmc" modified all
other instances. After initial versions of that patch, a new
change added reading nand data using gpmc exposed function.
In the final version this change was not taken care.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
memory as is now obtained via resource, upon freeing use
resource size. This also helps get rid of one macro.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
requesting, freeing gpmc cs is now handled fully
by gpmc, remove left out gpmc dependency as well
as unnecessary include of gpmc.h
Signed-off-by: Afzal Mohammed <afzal@ti.com>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
The pointer returned by kzalloc should be tested for NULL
to avoid potential NULL pointer dereference later. Incorrect
pointer was being tested for NULL. Bug introduced by commit fbcf62a3
(mtd: physmap_of: move parse_obsolete_partitions to become separate
parser).
This patch fixes this bug.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Cc: stable@kernel.org
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:
ec da 10 95 44 00 ec da
The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.
This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This code was broken because it assumed that all MTD devices were map-based.
Disable it for now, until it can be fixed properly for the next merge window.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When transparent huge pages were introduced, memory compaction and swap
storms were an issue, and the kernel had to be careful to not make THP
allocations cause pageout or compaction.
Now that we have working compaction deferral, kswapd is smart enough to
invoke compaction and the quadratic behaviour around isolate_free_pages
has been fixed, it should be safe to remove __GFP_NO_KSWAPD.
[minchan@kernel.org: Comment fix]
[mgorman@suse.de: Avoid direct reclaim for deferred compaction]
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Weinberger from Linutronix. Fastmap is designed to address UBI's slow scanning
issues. Namely, it introduces a new on-flash data-structure called "fastmap",
which stores the information about logical<->physical eraseblocks mappings.
So now to get this information just read the fastmap, instead of doing full
scan. More information here can be found in Richard's announcement in LKML
(Subject: UBI: Fastmap request for inclusion (v19)):
http://thread.gmane.org/gmane.linux.kernel/1364922/focus=1369109
One thing I want to explicitly say is that fastmap did not have large
enough linux-next exposure. It is partially my fault - I did not respond
quickly enough. I _really_ apologize for this. But it had good testing and
disabled by default, so I do not expect that we'll break anything.
Fastmap is declared as experimental so far, and it is off by default. We
did declare that the on-flash format may be changed. The reason for this is
that no one used it in real production so far, so there is a high risk that
something is missing. Besides, we do not have user-space tools supporting
fastmap so far.
Nevertheless, I suggest we merge this feature. Many people want UBI's scanning
bottleneck to be fixed and merging fastmap now should accelerate its production
use. The plan is to make it bullet-prove, somewhat clean-up, and make it the
default for UBI. I do not know how many kernel releases will it take.
Basically, I what I want to do for fastmap is something like Linus did for
btrfs few years ago.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Sqc
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc1-fastmap' of git://git.infradead.org/linux-ubi
Pull UBI fastmap changes from Artem Bityutskiy:
"This pull request contains the UBI fastmap support implemented by
Richard Weinberger from Linutronix. Fastmap is designed to address
UBI's slow scanning issues. Namely, it introduces a new on-flash
data-structure called "fastmap", which stores the information about
logical<->physical eraseblocks mappings. So now to get this
information just read the fastmap, instead of doing full scan. More
information here can be found in Richard's announcement in LKML
(Subject: UBI: Fastmap request for inclusion (v19)):
http://thread.gmane.org/gmane.linux.kernel/1364922/focus=1369109
One thing I want to explicitly say is that fastmap did not have large
enough linux-next exposure. It is partially my fault - I did not
respond quickly enough. I _really_ apologize for this. But it had
good testing and disabled by default, so I do not expect that we'll
break anything.
Fastmap is declared as experimental so far, and it is off by default.
We did declare that the on-flash format may be changed. The reason
for this is that no one used it in real production so far, so there is
a high risk that something is missing. Besides, we do not have
user-space tools supporting fastmap so far.
Nevertheless, I suggest we merge this feature. Many people want UBI's
scanning bottleneck to be fixed and merging fastmap now should
accelerate its production use. The plan is to make it bullet-prove,
somewhat clean-up, and make it the default for UBI. I do not know how
many kernel releases will it take.
Basically, I what I want to do for fastmap is something like Linus did
for btrfs few years ago."
* tag 'upstream-3.7-rc1-fastmap' of git://git.infradead.org/linux-ubi:
UBI: Wire-up fastmap
UBI: Add fastmap core
UBI: Add fastmap support to the WL sub-system
UBI: Add fastmap stuff to attach.c
UBI: Wire-up ->fm_sem
UBI: Add fastmap bits to build.c
UBI: Add self_check_eba()
UBI: Export next_sqnum()
UBI: Add fastmap stuff to ubi.h
UBI: Add fastmap on-flash data structures
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Make fastmap known to Kconfig, UBI Makefile and MAINTAINERS.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
To make fastmap possible the WL sub-system needs some
changes.
Mostly to support fastmaps pools.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fastmap uses ->fm_sem to stop EBA changes while writing
a new fastmap.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
self_check_eba() compares two ubi_attach_info objects.
Fastmap uses this function for self checks.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fastmap needs next_sqnum(), rename it to ubi_next_sqnum()
and make it non-static.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds fastmap specific data structures to ubi.h.
It moves also struct ubi_work to ubi.h as it is now needed
for more than one c file.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add the on-flash data structures neeed by fastmap
to ubi-media.h
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
handling. We used to reserve 2% of the partition, but now we are
more aggressive and we reserve 2% of the entire chip, which is
what actually manufacturers specify in data sheets. We introduced
an option to users to override the default, though.
There are a couple of fixes as well, and a number of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=95SE
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"The main change is the way we reserve eraseblocks for bad blocks
handling. We used to reserve 2% of the partition, but now we are more
aggressive and we reserve 2% of the entire chip, which is what
actually manufacturers specify in data sheets. We introduced an
option to users to override the default, though.
There are a couple of fixes as well, and a number of cleanups."
* tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi: (24 commits)
UBI: fix trivial typo 'it' => 'is'
UBI: load after mtd device drivers
UBI: print less
UBI: use pr_ helper instead of printk
UBI: comply with coding style
UBI: erase free PEB with bitflip in EC header
UBI: fix autoresize handling in R/O mode
UBI: add max_beb_per1024 to attach ioctl
UBI: allow specifying bad PEBs limit using module parameter
UBI: check max_beb_per1024 value in ubi_attach_mtd_dev
UBI: prepare for max_beb_per1024 module parameter addition
UBI: introduce MTD_PARAM_MAX_COUNT
UBI: separate bad_peb_limit in a function
arm: sam9_l9260_defconfig: correct CONFIG_MTD_UBI_BEB_LIMIT
UBI: use the whole MTD device size to get bad_peb_limit
mtd: mtdparts: introduce mtd_get_device_size
mtd: mark mtd_is_partition argument as constant
arm: sam9_l9260_defconfig: remove non-existing config option
UBI: kill CONFIG_MTD_UBI_BEB_RESERVE
UBI: limit amount of reserved eraseblocks for bad PEB handling
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Datasheets for the following Samsung NAND parts (both MLC and SLC) describe
extensions to the Samsung 6-byte extended ID decoding table:
K9GBG08U0A (MLC, 6-byte ID)
K9GAG08U0F (MLC, 6-byte ID)
K9FAG08U0M (SLC, 6-byte ID)
The table found in K9GAG08U0F, p.44, contains a superset of the information
found in other previous datasheets.
This patch adds support for all of these chips, with 512B and 640B OOB sizes.
It also changes the detection pattern such that this table applies to all
Samsung 6-byte ID NAND, not just MLC. This is safe, according to the NAND
parameter data I have collected:
Note that nand_base.c does not yet support the bad block marker scheme defined
for these chips (i.e., scan 1st and last page for BB markers).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Hynix has introduced a new ID decoding scheme for their newer MLC, some of
which don't support ONFI. The following devices all follow the pattern given in
the datasheet for Hynix H27UBG8T2B, p.22:
Hynix H27UAG8T2A
Hynix H27UBG8T2A
Hynix H27UBG8T2B
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When decoding the extended ID bytes of a NAND chip, we have to calculate the ID
length according to some heuristic patterns (e.g., Does the ID wrap around?
Does it end in trailing zeros?). Currently, these heuristics are built into
complicated if/else blocks that can be hard to understand.
Now, these checks can be done generically in a function, making them more
robust and reusable. In fact, this sort of calculation is needed in future
additions to nand_base.c. And with this advancement, we get the added benefit
of a more readable "extended ID decode".
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When detecting NAND parameters, the code gets a little ugly so that the
logic is obscured. Try to remedy that by moving code to separate functions
that have well-defined purposes.
This patch splits out the simple ID decode functionality, where all the
information regarding NAND size/blocksize/pagesize/oobsize/busw is encoded in
the first two bytes of the ID string.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When detecting NAND parameters, the code gets a little ugly so that the
logic is obscured. Try to remedy that by moving code to separate functions
that have well-defined purposes.
This patch splits out the extended ID decode functionality, which handles
decoding the 3rd-8th ID bytes to determine NAND device parameters.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When detecting NAND parameters, the code gets a little ugly so that the
logic is obscured. Try to remedy that by moving code to separate functions
that have well-defined purposes.
This patch splits the bad block marker options detection into its own function,
away from the other parameters (e.g., chip size, page size, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of reading 2 bytes then later 8 bytes, we can simply read all 8
bytes from the start.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We don't actually use the 'ret' variable; we set it, test it, and then it dies.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While building an allyesconfig for UML I received this error message(s):
drivers/mtd/nand/docg4.c: In function 'probe_docg4':
drivers/mtd/nand/docg4.c:1272:2: error: implicit declaration of function
'ioremap' [-Werror=implicit-function-declaration]
drivers/mtd/nand/docg4.c:1272:10: warning: assignment makes pointer from
integer without a cast [enabled by default]
drivers/mtd/nand/docg4.c:1327:2: error: implicit declaration of function
'iounmap' [-Werror=implicit-function-declaration]
which is caused by the missing implementations on UML.
This patch adds this missing HAS_IOMEM dependency and prevents the driver from
being build on platforms with no HAS_IOMEM
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current code initializes the timing registers at very time
we call the gpmi_begin(). This really wastes the cpu cycles.
Add a new flag to let the gpmi driver initializes the timing registers
only one time.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the frequency on the nand chip pins is above 33MHz,
the nand EDO(extended Data Out) timing could be applied.
The GPMI implements a Feedback read strobe to sample the read data in
the EDO timing mode.
This patch adds the EDO feature for the gpmi-nand driver.
For some onfi nand chips, the mode 4 is the fastest;
while for other onfi nand chips, the mode 5 is the fastest.
This patch only adds the support for the fastest asynchronous timing mode.
So this patch only supports the mode 4 and mode 5.
I tested several Micron's ONFI nand chips with EDO enabled,
take Micron MT29F32G08MAA for example (in mode 5, 100MHz):
1) The test result BEFORE we add the EDO feature:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size 209715200, eraseblock size 524288,
page size 4096, count of eraseblocks 400,
pages per eraseblock 128, OOB size 218
.......................................
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 3632 KiB/s
.......................................
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 3554 KiB/s
.......................................
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 3592 KiB/s
.......................................
=================================================
2) The test result AFTER we add the EDO feature:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size 209715200, eraseblock size 524288,
page size 4096, count of eraseblocks 400,
pages per eraseblock 128, OOB size 218
.......................................
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 19555 KiB/s
.......................................
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 17319 KiB/s
.......................................
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 18339 KiB/s
.......................................
=================================================
3) The read data performance is much improved by more then 5 times.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The default frequencies of the extra clocks are 200MHz.
The current code sets the extra clocks to 44.5MHz.
When i add the EDO feature to gpmi, i have to revert the extra clocks
to 200MHz.
So it is better that we do not set the default values for the extra
clocks. The driver runs well even when we do not set the default values for
extra clocks.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The setting DLL code is a little mess.
Just simplify the code and the comments.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add the WRN_DLY_SEL field for HW_GPMI_CTRL1.
This field is used as delay for gpmi write strobe.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current code will gets the clock frequency which is used by
gpmi_nfc_compute_hardware_timing(). It makes the code a little mess.
So move the `get clock frequency` code to the
gpmi_nfc_compute_hardware_timing() itself. This makes the code tidy
and clean.
This patch also uses the macro NSEC_PER_SEC to replace the `1000000000`.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The gpmi_nfc_compute_hardware_timing{} should contains all the
fields setting for gpmi timing registers. It already contains the fields
for HW_GPMI_TIMING0 and HW_GPMI_CTRL1.
So it is better to add a new field setting for HW_GPMI_TIMING1 in
this data structure. This makes the code more clear in logic.
This patch also changes some comments to make the code more readable.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the set-features(0xef)/get-features(0xee) helpers for ONFI nand.
Also add the necessary macros.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If override size is too big, the module was actually loaded instead of
failing, because retval was not set.
This lead to memory corruption with the use of the freed structs nandsim
and nand_chip.
Cc: stable@vger.kernel.org
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently the docg4's ecc.read_page() method returns -EBADMSG when
uncorrectable bitflips occur. This is wrong; 0 should be returned in
this case. An error code should only be returned by this method in the
case of a hardware error (probably -EIO).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In nand_bbt.c, a hardcoded value was used instead of the define meant
for that, so we use the define.
There's no functional change.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver is being removed as part of the cleanup of the bcmring
SoC from mainline as it is no longer maintained.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.
This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds the double bit error detection test cases listed below:
* Prepare data block with double bit error and ECC data without
corruption, and verify that the uncorrectable error is detected by
__nand_correct_data().
* Prepare data block with single bit error and ECC data with single bit
error, and verify that the uncorrectable error is detected.
* Prepare data block without corruption and ECC data with double bit
error, and verify that the uncorrectable error is detected.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds the single bit error correction test case listed below:
Prepare data block without corruption and ECC data with single bit error,
and verify that the data block is preserved by __nand_correct_data().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds no corruptin test case listed below:
Prepare data block and ECC data with no corruption, and verify that
the data block is preserved by __nand_correct_data()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This rewrites the entire test routine in order to make it easy to add more
tests by later changes and minimize duplication of each tests as much as
possible.
Now that each test is described by the members of struct nand_ecc_test:
- name: descriptive testname
- prepare: function to prepare data block and ecc with artifical corruption
- verify: function to verify the result of correcting data block
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently inject_single_bit_error() is used to inject single bit error
into randomly selected bit position of the 256 or 512 bytes data block.
Later change will add tests which inject bit errors into the ecc code.
Unfortunately, inject_single_bit_error() doesn't work for the ecc code
which is not a multiple of sizeof(unsigned long).
Because bit fliping at random position is done by __change_bit().
For example, flipping bit position 0 by __change_bit(0, addr) modifies
3rd byte (32bit) or 7th byte (64bit) on big-endian systems.
Using little-endian version of bitops can fix this issue. But
little-endian version of __change_bit is not yet available.
So this defines __change_bit_le() locally in a similar fashion to
asm-generic/bitops/le.h and use it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This tests ECC biterror recovery on a single NAND page. Mostly intended
to test ECC hardware and low-level NAND driver.
There are two test modes:
0 - artificially inserting bit errors until the ECC fails
This is the default method and fairly quick. It should
be independent of the quality of the FLASH.
1 - re-writing the same pattern repeatedly until the ECC fails.
This method relies on the physics of NAND FLASH to eventually
generate '0' bits if '1' has been written sufficient times. Depending
on the NAND, the first bit errors will appear after 1000 or
more writes and then will usually snowball, reaching the limits
of the ECC quickly.
The test stops after 10000 cycles, should your FLASH be exceptionally
good and not generate bit errors before that. Try a different page
offset in that case.
Please note that neither of these tests will significantly 'use up' any FLASH
endurance. Only a maximum of two erase operations will be performed.
Signed-off-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com.au>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie <shijie8@gmail.com> explains:
Assume we have a 1GiB(8Gib) NAND chip, and we set the partitions
in the command line like this:
#gpmi-nand:100m(boot),100m(kernel),1g(rootfs)
In this case, the partition truncating occurs. The current code will
get the following result:
----------------------------------
root@freescale ~$ cat /proc/mtd
dev: size erasesize name
mtd0: 06400000 00040000 "boot"
mtd1: 06400000 00040000 "kernel"
----------------------------------
It is obvious that we lost the truncated partition `rootfs` which should
be 824MiB in this case.
Also, forbid 0-sized partitions.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With the new i.mx clock framework the mxc_nand clock is registered as:
clk_register_clkdev(clk[nfc_gate], NULL, "mxc_nand");0")
So we do not need to pass "nfc" string and can use NULL instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Quoting from the datasheet for S25FL064P, rev. 05, Nov 18 2011, § 9.17:
"A 64 kB[sic] sector erase (D8h) command issued on 4 kB or 8 kB erase
sectors will erase all sectors in the specified 64 kB region. However,
please note that a 4 kB sector erase (20h) or 8 kB sector erase (40h)
command will not work on a 64 kB sector."
Referring further to Table 8.1 and Table 8.2, it is clearly seen
that most of the sectors are 64KiB; therefore disable this 4KiB
erase support since it's valid only on first/last sectors.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This registers MTD driver for serial flash platform device. Right now it
supports reading only, writing still has to be implemented.
Artem: minor amendments.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently the data blocks which is used to test single bit error
correction is allocated statically and injecting single bit error is
implemented by using __change_bit() which must operate on the memory
aligned to the size of an "unsigned long". But there is no such
guarantee for statically allocated array.
This fix the issue by allocating the data block dynamically by
kmalloc(). It also allocate the ecc code dynamically instead of
allocating statically on stack.
The reason to allocate the ecc code dynamically is that later change
will add tests which inject bit errors into the ecc code by bitops.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This includes the message related changes:
- Use pr_* instead of printk
- Print hexdump of ECC code if test fails
- Change log level for hexdump of data from KERN_DEBUG to KERN_INFO
- Factor out the hexdump code into a separate function
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Return -EINVAL instead of -1 (-EPERM) when test fails.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Including linux/jiffies.h was required for calling srandom32(jiffies)
that has already been removed.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
devm free functions should not have to be explicitly used.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Clean-up the driver a bit to make it easier to read and amend the coding style.
Mostly these are changes like:
if (a)
{
}
=>
if (a) {
}
Some extra blank lines were added.
Indentation was changed to use tabs instead of spaces.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch revises and fixes error handling in the command line mtd
partitions parser. Namely:
1. we ignored return code of 'mtdpart_setup_real()'.
2. instead of returning 0 for failure and 1 for success, teach
'mtdpart_setup_real()' to return real error codes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver provides parser detecting partitions on BCM47XX flash
memories. It has many differences in comparison to BCM63XX, like:
1) Different CFE with no more trivial MAGICs
2) More partitions types (board_data, ML, POT)
3) Supporting more than 1 flash on a device
which resulted in decision of writing new parser.
It uses generic mtd interface and was successfully tested with Netgear
WNDR4500 router which has 2 flash memories: serial one and NAND one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not have to initialize variables for .bss to 0 in Linux.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Unloading the omap2 nand driver missed to release the memory region which will
result in not being able to request it again if one want to load the driver
later on.
This patch fixes following error when loading omap2 module after unloading:
---8<---
~ $ rmmod omap2
~ $ modprobe omap2
[ 37.420928] omap2-nand: probe of omap2-nand.0 failed with error -16
~ $
--->8---
This error was introduced in 67ce04bf27 which
was the first commit of this driver.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Unlocking may take up to 1.4 seconds on some Intel flashes. So
lets use a max. of 1.5 seconds (1500ms) as timeout.
See "Clear Block Lock-Bits Time" on page 40 in
"3 Volt Intel StrataFlash Memory" 28F128J3,28F640J3,28F320J3 manual
from February 2003
This patch also fixes some other problems with this timeout:
- Don't use HZ in timeout "calculation"!
While testing we noticed that an unlocking timeout occured with
HZ=1000 and didn't occur with HZ=300. This was because the
timeout parameter was calculated differently depending on the
HZ value. Now a fixed value of 1500ms is used.
- The last parameter of WAIT_TIMEOUT (defined to
inval_cache_and_wait_for_operation) has to be passed in
micro-seconds. So multiply the ms value with 1000 and not 100
to calculate this value.
- Use variable name "mdelay" instead of misleading "udelay".
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Stephan Gatzka <stephan@gatzka.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Added a NAND device flag for subpage read support. Previously this was
hard coded based on large page and soft ECC.
Updated base NAND driver to use the new subpage read flag if the NAND is
large page and soft ECC.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit abcda1dc ('arm: plat-orion: introduce PLAT_ORION_LEGACY hidden
config option') currently pending in linux-next will make the ARCH_MVEBU
platform select PLAT_ORION, which means that now all Orion drivers can
be enabled on ARCH_MVEBU. This works fine for most drivers, except for
orion_nand, because it includes <mach/hardware.h>, but mach-mvebu does
not have a mach/hardware.h header (it is considered as a deprecated
practice).
It turns out that the <mach/hardware.h> include in orion_nand is not
necessary: the driver builds perfectly fine without it, so we simply
get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Return an error code if test fails in order to detect a test case failure
by invoking tests repeatedly like this:
while sudo modprobe mtd_nandecctest; do
sudo modprobe -r mtd_nandecctest
done
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It is unnecessary for this driver to call srandom32() in module_init.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The LPC32xx's DT-only conversion of the MLC NAND driver makes NAND config via
platform_data obsolete. Dropped by this patch.
Further, the driver really needs CONFIG_OF, which is already reflected by the
dependency on ARCH_LPC32XX which depends on CONFIG_OF. So also dropping
CONFIG_OF ifdefs.
There is still platform_data necessary to supply the dma_filter callback for
the dma engine. This is a completely different data structure than the old
platform_data for NAND config, so renaming some old "pdata" variable to "ncfg"
to prevent confusion with the new platform data.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The LPC32xx's DT-only conversion of the SLC NAND driver makes NAND config via
platform_data obsolete. Dropped by this patch.
Further, the driver really needs CONFIG_OF, which is already reflected by the
dependency on ARCH_LPC32XX which depends on CONFIG_OF. So also dropping
CONFIG_OF ifdefs.
There is still platform_data necessary to supply the dma_filter callback for
the dma engine. This is a completely different data structure than the old
platform_data for NAND config, so renaming some old "pdata" variable to "ncfg"
to prevent confusion with the new platform data.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allow MTD_NAND_GPMI_NAND to be built as module.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When building MTD_NAND_GPMI_NAND as module, the following error shows up:
ERROR: "nand_update_bbt" [drivers/mtd/nand/gpmi-nand/gpmi_nand.ko] undefined!
Export nand_update_bbt to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rename 'len' variable of create_bbt/scan_block_fast/scan_block_full to
'numpages', since it really means number of pages to scan when
searching for the BBM (and not the byte length of the scan).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the following warnings:
‘s3c2410_nand_correct_data’ defined but not used [-Wunused-function]
‘s3c2410_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2412_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2440_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2410_nand_calculate_ecc’ defined but not used [-Wunused-function]
‘s3c2412_nand_calculate_ecc’ defined but not used [-Wunused-function]
‘s3c2440_nand_calculate_ecc’ defined but not used [-Wunused-function]
The above functions are called only when CONFIG_MTD_NAND_S3C2410_HWECC
is defined. Thus making them conditional.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
devm_* functions are device managed functions and make cleanup code
simpler and smaller.
devm_kzalloc, devm_clk_get and devm_request_and_ioremap functions
are used.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Err has only been initialized to 0 at this, so it is not possible that this
test can be true.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We may cause a memory leak when the @types has more then one parser.
Take the `default_mtd_part_types` for example. The default_mtd_part_types has
two parsers now: `cmdlinepart` and `ofpart`.
Assume the following case:
The kernel command line sets the partitions like:
#gpmi-nand:20m(boot),20m(kernel),1g(rootfs),-(user)
But the devicetree file(such as arch/arm/boot/dts/imx28-evk.dts) also sets
the same partitions as the kernel command line does.
In the current code, the partitions parsed out by the `ofpart` will
overwrite the @pparts which has already set by the `cmdlinepart` parser,
and the the partitions parsed out by the `cmdlinepart` is missed.
A memory leak occurs.
So we should break the code as soon as we parse out the partitions,
In actually, this patch makes a priority order between the parsers.
If one parser has already parsed out the partitions successfully,
it's no need to use another parser anymore.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
problems with JFFS2 usage, as the local bus (LPB) doesn't support
unaligned accesses as implemented in the JFFS2 code via memcpy().
By defining "no-unaligned-direct-access", the flash will not be
exposed directly to the MTD users (e.g. JFFS2) any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use devm_kzalloc for all calls to kzalloc and not just the first. Use devm
functions for other allocations as well.
Move the call to platform_get_resource(pdev, IORESOURCE_MEM, 0) closer to
where its result is passed to devm_request_and_ioremap to make the lack of
need for a NULL test more evident.
The semantic match that finds the inconsistency is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
*devm_kzalloc(...)
...
*kzalloc(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver uses plat_nand. As the platform_device is loaded from DT, we need
to lookup the node and attach our xway specific "struct platform_nand_data"
to it.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If plat_nand loads and the platform_data is not properly set it will segfault.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The manufacturer datasheet can be found on the Micron website,
under the name n25q_256mb_3v_65nm.pdf:
http://www.micron.com/search?source=ps&q=n25q_256mb_3v_65nm
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removes disabled printk (which should be dev_dbg these days) as well
as #if 0 blocks (which are trivial to reimplement if ever needed) to
meet basic CodingStyle guidelines.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is new format specified that helps to dump small buffers. It makes the
code simpler and nicer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add OF support for the davinci nand controller.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The uclinux.c map driver has traditionally been used only on non-MMU based
systems. But there is no fundamental reason it can't be used on systems
running with virtual memory.
Some ColdFire CPU based systems now have full paged MMU hardware and can use
the uclinux.c mapping driver, so making the uclinux.c driver configuration
depend on !CONFIG_MMU doesn't make sense now. Allow the CONFIG_MTD_UCLINUX
option to be enabled if CONFIG_COLDFIRE is enabled. (I have chosen not to
just more generally allow uclinux.c for any MMU type to keep this option
hidden for most systems that are not interested in setting it).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The uclinux.c mapping driver uses ioremap_nocache() to map its physical
mapping address to a system virtual address. Problem is that the region
it is mapping is not device memory. It is ordinary system RAM. On most
non-MMU systems this doesn't matter, and the mapping is always a 1:1
translation of the address. On paged memory systems on some architectures
the page table mappings are not compatible between normal RAM and device
memory.
If we want to use the uclinux.c mapping driver on real MMU enabled systems
we should be using the kernel virtual address that the mapping is at. For
architectures that support the traditional initrd they use phys_to_virt or
__va to convert the physical start initrd address to a kernel usable virtual
address. The uclinux filesystem mapping is even more restrictive than the
typical initrd, it always follows the kernels own bss section (so always in
directly mapped memory). Therefore we can use the usual phys_to_virt to
translate the physical start address to a virtual address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the following checkpatch warnings:
WARNING: line over 80 characters
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes checkpatch warnings and errors related to whitespaces.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the following checkpatch errors:
ERROR: do not initialise statics to 0 or NULL
+static int hardware_ecc = 0;
ERROR: do not initialise statics to 0 or NULL
+static const int clock_stop = 0;
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the following checkpatch warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the code simpler by eliminating module_init() and
module_exit().
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Include IMX6 in the list of supported SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because we can have a single kernel to support multiple machines, we
need to make loading specific drivers for the target platform only.
For this, driver is converted to the platform driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Update driver autcpu12-nvram.c so it compiles; map_read32/map_write32
no longer exist in the kernel so the driver is totally broken.
Additionally, map_info name passed to simple_map_init is incorrect.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
without this the gpio will not be muxed as a gpio by the current custom pinmux
or later by the pinctrl
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch does two closely related things:
(1) Currently the ecc.read_page() method does not fill the nand->oob_poi buffer
with the oob data, but instead reads oob into a local buffer. Fix this by
filling the oob_poi buffer instead of a local buffer. The 'oob_required'
argument is quietly ignored; the device must always read oob after the page
data, and it is presumed that there's no harm in filling oob_poi, even when not
explicitly requested.
(2) Always read oob from the device in ecc.read_oob(), instead of copying it
from a local buffer under some circumstances.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/devices/spear_smi.c: In function 'spear_smi_probe':
drivers/mtd/devices/spear_smi.c:984:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
dev_get_platdata returns a pointer, so the failure value would be NULL
rather than a negative integer.
The semantic match that finds this problem is: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e;
statement S1,S2;
@@
*x = dev_get_platdata(...)
... when != x = e
*if (x < 0) S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the MLC NAND driver independent of the single AMBA DMA engine
driver by using the platform data provided dma_filter callback.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the SLC NAND driver independent of the single AMBA DMA engine
driver by using the platform data provided dma_filter callback.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
None of these scanning functions use MTD_OPS_RAW mode any more, so there's
really nothing 'raw' about them. Rename them to (hopefully) make the code
a little clearer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
scan_read_raw_oob() is used in only in places where the MTD_OPS_PLACE_OOB mode
is preferable to MTD_OPS_RAW mode, so use MTD_OPS_PLACE_OOB instead.
MTD_OPS_PLACE_OOB provides the same functionality with the potential[1] added
bonus of error correction.
This brings scan_block_full() in line with scan_block_fast() so that they
both read bad block markers with MTD_OPS_PLACE_OOB. This can help in
preventing 0xff markers (in good blocks) from being interpreted as bad
block indicators in the presence of a single bitflip.
Note that ECC error codes (EUCLEAN or EBADMSG) are already silently
ignored in all users of scan_read_raw_oob().
[1] Few drivers perform proper error correction on OOB data. In those
cases, the use of MTD_OPS_RAW vs. MTD_OPS_PLACE_OOB is not
significant.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some nand_bbt code can be shortened by using memcmp() and memchr_inv().
As an added bonus, there is a possible performance benefit.
Borrowed some code from Akinobu Mita.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The return codes for read_abs_bbts() and search_read_bbts() are always
non-zero, and so don't have much meaning. Just remove them.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd_read_oob() has some unexpected similarities to mtd_read(). For
instance, when ops->datbuf != NULL, nand_base.c might return max_bitflips;
however, when ops->datbuf == NULL, nand_base's code potentially could
return -EUCLEAN (no in-tree drivers do this yet). In any case where the
driver might return max_bitflips, we should translate this into an
appropriate return code using the bitflip_threshold.
Essentially, mtd_read_oob() duplicates the logic from mtd_read().
This prevents users of mtd_read_oob() from receiving a positive return
value (i.e., from max_bitflips) and interpreting it as an unknown error.
Artem: amend comments.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to the implementation of the following loop at the end
of jedec_probe():
776 for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
777 info = (void *)m25p_ids[tmp].driver_data;
778 if (info->jedec_id == jedec) {
779 if (info->ext_id != 0 && info->ext_id != ext_jedec)
780 continue;
781 return &m25p_ids[tmp];
782 }
783 }
In particular line 779 in the above numbering, the chips with ext_id != 0 must
be ordered first in the list of chips (m25p_ids[]).
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The gpmi nand driver may needs several clocks(MX6Q needs five clocks).
In the old clock framework, all these clocks are chained together,
all you need is to manipulate the first clock.
But the kernel uses the common clk framework now, which forces us to
get the clocks one by one. When we use them, we have to enable them
one by one too.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Check the new oob_required flag and only copy the OOB data to the internal
buffer if needed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Elements have been copied "manually" in a loop. Better use memcpy().
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sasha Levin has been running trinity in a KVM tools guest, and was able
to trigger the BUG_ON() at arch/x86/mm/pat.c:279 (verifying the range of
the memory type). The call trace showed that it was mtdchar_mmap() that
created an invalid remap_pfn_range().
The problem is that mtdchar_mmap() does various really odd and subtle
things with the vma page offset etc, and uses the wrong types (and the
wrong overflow) detection for it.
For example, the page offset may well be 32-bit on a 32-bit
architecture, but after shifting it up by PAGE_SHIFT, we need to use a
potentially 64-bit resource_size_t to correctly hold the full value.
Also, we need to check that the vma length plus offset doesn't overflow
before we check that it is smaller than the length of the mtdmap region.
This fixes things up and tries to make the code a bit easier to read.
Reported-and-tested-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use 'late_initcall()' in UBI to make sure it initializes after MTD drivers.
Signed-off-by: Jiang Lu <lu.jiang@windriver.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This is only used by omap1.
And to fix things properly, this should not be included
from the drivers at all.
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fzT6
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQUUgbAAoJEBvUPslcq6VzsEgQANbHSsPDajdFnaCn3goS16M3
Nwmnvqd3Ay4VqhLpJuiF9SWzPtCno0gu/9caUKhodYDrHDVttdMKQWKLsmkSPFOD
uHnKToA3y0J5O/KQJB+bubinZvcHNnBwCgP6YFposFwH561aCRhp4DiCIlqAiqlV
g6jyEtTkOrIyHULokgFSmWrLDcTxvx4lWyZbmeltju4KXzzfPojc6m4daVN9Z3cQ
VP9+6mLuJcF/aIbdyGnxg7pgsfy6+roHI1+vHfufVEyTt1funm1Mt1Wq+kUFC0XW
YRQILq82tr3OgvcB3xmXllE3XcklN4Vv922Up0fQ+8OV36jA2q6N5vTsk8fctuD4
8O+j4kmomCEavj2JEIB5SFfsZ+Cdycx79+1pvOtDSYOM7svFpQs6kdhq+JXGRSql
W00xgLQj82tmXpaLV36pXPGoc7ZXQolQbc6SYFQn8oHTTvHDdFiQkG5TKafj7r5u
ayaV/VqytSy+Hiq8XWNpEjfxn467fQ5UmHXQoVAIZnpk323SpPbLQ5aDOMk/9+DT
u0mDnIP4k6w8ViTnalLPEBOqqpZZo358t+cRD1kD55X4IR2YPSFhrhJTq23Z9Rv3
EW9ZUQYrK6WDuYO8/4SZ1J/HTx5MFb1Na6dKAXwO3v0S7CBzIbN9gqbU7IxfQ8ZA
qKT726r923PHKL2x8VZc
=GLSh
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparseirq-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
* tag 'omap-cleanup-sparseirq-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: Move SoC specific headers from plat to mach for omap1
ARM: OMAP2+ Move SoC specific headers to be local to mach-omap2
ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+
ARM: OMAP: Remove unused old gpio-switch.h
ARM: OMAP1: Move plat/irqs.h to mach/irqs.h
ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ
ARM: OMAP2+: Prepare for irqs.h removal
W1: OMAP HDQ1W: Remove dependencies to mach/hardware.h
Input: omap-keypad: Remove dependencies to mach includes
ARM: OMAP: Move gpio.h to include/linux/platform_data
ARM: OMAP2+: Remove hardcoded twl4030 gpio_base, irq_base and irq_end
ARM: OMAP2+: Remove unused nand_irq for GPMC
ARM: OMAP2+: Make INTCPS_NR_IRQS local for mach-omap2/irq.c
ARM: OMAP1: Define OMAP1_INT_I2C locally
ARM: OMAP1: Move define of OMAP_LCD_DMA to dma.h
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=utuw
-----END PGP SIGNATURE-----
Merge tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the nomadik include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
closer for being just a regular device driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A43b
-----END PGP SIGNATURE-----
mergetag object cf3a6ec2c0
type commit
tag cleanup-omap-tags-for-v3.7
tagger Tony Lindgren <tony@atomide.com> 1347323254 -0700
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=utuw
-----END PGP SIGNATURE-----
Merge tags 'omap-devel-gpmc-fixed-for-v3.7' and 'cleanup-omap-tags-for-v3.7' into cleanup-sparseirq
Changes for GPMC (General Purpose Memory Controller) that take it
closer for being just a regular device driver.
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
plat/board.h file is now empty - remove it.
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'soc-core' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: mach-shmobile: Add compilation support for dtbs using 'make dtbs'
+ sync to 3.6-rc3
The io-pci series has gained a merge to resolve a nontrivial
conflict.
* cleanup/io-pci:
ARM: Fix ioremap() of address zero
Also includes an update to Linux 3.6-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UBI was mistakingly using 'kfree()' instead of 'kmem_cache_free()' when
freeing "attach eraseblock" structures in vtbl.c. Thankfully, this happened
only when we were doing auto-format, so many systems were unaffected. However,
there are still many users affected.
It is strange, but the system did not crash and nothing bad happened when
the SLUB memory allocator was used. However, in case of SLOB we observed an
crash right away.
This problem was introduced in 2.6.39 by commit
"6c1e875 UBI: add slab cache for ubi_scan_leb objects"
A note for stable trees:
Because variable were renamed, this won't cleanly apply to older kernels.
Changing names like this should help:
1. ai -> si
2. aeb_slab_cache -> seb_slab_cache
3. new_aeb -> new_seb
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org [v2.6.39+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI currently prints a lot of information when it mounts a volume, which
bothers some people. Make it less chatty - print only important information
by default.
Get rid of 'dbg_msg()' macro completely.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Without this patch, these PEB are not scrubbed until we put data in them.
Bitflip can accumulate latter and we can loose the EC header (but VID header
should be intact and allow to recover data).
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently UBI fails in autoresize when it is in R/O mode (e.g., because the
underlying MTD device is R/O). This patch fixes the issue - we just skip
autoresize and print a warning.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch provides a possibility to set the "maximum expected number of
bad blocks per 1024 blocks" (max_beb_per1024) for each mtd device using
the UBI_IOCATT ioctl.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch provides the possibility to adjust the "maximum expected number of
bad blocks per 1024 blocks" (max_beb_per1024) for each mtd device.
The majority of NAND devices have their max_beb_per1024 equal to 20, but
sometimes it's more.
Now, we can adjust that via a kernel parameter:
ubi.mtd=<name|num|path>[,<vid_hdr_offs>[,max_beb_per1024]]
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
max_beb_per1024 shouldn't be negative, and a 0 value will be treated as
the default value. For the upper bound, 768/1024 should be enough.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch prepare the way for the addition of max_beb_per1024 module
parameter. There's no functional change.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
No functional changes here, just to prepare for next patch.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
On NAND flash devices, UBI reserves some physical erase blocks (PEB) for
bad block handling. Today, the number of reserved PEB can only be set as a
percentage of the total number of PEB in each MTD partition. For example, for a
NAND flash with 128KiB PEB, 2 MTD partition of 20MiB (mtd0) and 100MiB (mtd1)
and 2% reserved PEB:
- the UBI device on mtd0 will have 2 PEB reserved
- the UBI device on mtd1 will have 16 PEB reserved
The problem with this behaviour is that NAND flash manufacturers give a
minimum number of valid block (NVB) during the endurance life of the
device, e.g.:
Parameter Symbol Min Max Unit Notes
--------------------------------------------------------------
Valid block number NVB 1004 1024 Blocks 1
From this number we can deduce the maximum number of bad PEB that a device will
contain during its endurance life: a 128MiB NAND flash (1024 PEB) will not have
less than 20 bad blocks during the flash endurance life.
But the manufacturer doesn't tell where those bad block will appear. He doesn't
say either if they will be equally disposed on the whole device (and I'm pretty
sure they won't). So, according to the datasheets, we should reserve the
maximum number of bad PEB for each UBI device (worst case scenario: 20 bad
blocks appears on the smallest MTD partition).
So this patch make UBI use the whole MTD device size to calculate the maximum
bad expected eraseblocks.
The Kconfig option is in per1024 blocks, thus it can have a default value of 20
which is *very* common for NAND devices.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'mtd_get_device_size()' returns the size of the whole MTD device, that is the
mtd_info master size. This will be used by UBI to calculate the maximum number
of bad blocks (MBB) on a MTD device.
Artem: amended the patch a bit.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'struct mtd_info' is not modified by 'mtd_is_partition()' so it can be marked
as "const".
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_MTD_UBI_BEB_RESERVE and MIN_RESEVED_PEBS are no longer used,
since the amount of reserved eraseblocks for bad PEB handling is now
derived from 'ubi->bad_peb_limit' (ubi's maximum expected bad
eraseblocks).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
The existing mechanism of reserving PEBs for bad PEB handling has two
flaws:
- It is calculated as a percentage of good PEBs instead of total PEBs.
- There's no limit on the amount of PEBs UBI reserves for future bad
eraseblock handling.
This patch changes the mechanism to overcome these flaws.
The desired level of PEBs reserved for bad PEB handling (beb_rsvd_level)
is set to the maximum expected bad eraseblocks (bad_peb_limit) minus the
existing number of bad eraseblocks (bad_peb_count).
The actual amount of PEBs reserved for bad PEB handling is usually set
to the desired level (but in some circumstances may be lower than the
desired level, e.g. when attaching to a device that has too few
available PEBs to satisfy the desired level).
In the case where the device has too many bad PEBs (above the expected
limit), then the desired level, and the actual amount of PEBs reserved
are set to zero. No PEBs will be set aside for future bad eraseblock
handling - even if some PEBs are made available (e.g. by shrinking a
volume).
If another PEB goes bad, and there are available PEBs, then the
eraseblock will be marked bad (consuming one available PEB). But if
there are no available PEBs, ubi will go into readonly mode.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Introduce 'ubi->bad_peb_limit', which specifies an upper limit of PEBs
UBI expects to go bad. Currently, it is initialized to a fixed percentage
of total PEBs in the UBI device (configurable via CONFIG_MTD_UBI_BEB_LIMIT).
The 'bad_peb_limit' is intended to be used for calculating the amount of PEBs
UBI needs to reserve for bad eraseblock handling.
Artem: minor amendments.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
GPMC platform initialization provides it's clients
with interrupts that can be used through struct
resource. Make use of it for irq mode functionality.
Also now write protect disable is done by GPMC,
hence remove it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[tony@atomide.com: updated to fix new warnings introduced]
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc initialization for onenand done by platform code now provides
onenand address space as memory resource. Hence remove usage of
gpmc_cs_request in onenand driver and obtain memory details from
resource structure.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc initialization done by platform code now updates struct resource
with the address space alloted for nand. Use this interface to obtain
memory rather than relying on platform data field - phys_base.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPMC platform initialization has been modified to fill NAND
platform data with GPMC NAND register details. As these
registers are accessible in NAND driver itself, configure
NAND in GPMC by itself.
Modified prefetch and ecc functions are logically same as
the corresponding exported symbols from GPMC code.
Note: Verfying that other CS have not yet enabled for
prefetch & ecc has to be incorporated. Currently this
causes no issues as there are no boards that use NAND
on multiple CS. With ongoing GPMC driver migration,
perhaps it would be better to consider NAND connected
on multiple CS as a single peripheral using multiple CS.
This would make handling multiple CS issues easier.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Having missed the merge window, update to 3.6-rc2 to avoid conflicts with
new patches.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
This patch contains a hack to get the DMA resources of the device when
probed from a devicetree node. This can be removed once a generic DMA
controller framework lands.
A mtd_part_parser_data is passed mtd_device_parse_register which
contains a reference to the device node, so MTD partitions can be
added as children.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
AT91 SoC related code modifications: a cleanup in defconfigs and
a one liner in a board file.
The most important is the move to atmel-mci driver in AT91 SoC & boards.
The old at91_mci (marked as deprecated) will be removed in 3.7. So all
platform data for this old driver are erased and replace by information
needed by atmel-mci driver.
* tag 'at91-for-next-soc' of git://github.com/at91linux/linux-at91:
ARM: at91: add atmel-mci support for chips and boards which can use it
ARM: at91/defconfig: change the MCI driver to use in defconfigs
ARM: at91: set i2c_board_info.type to "ds1339" directly
ARM: at91/defconfig: Remove unaffected config option
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jonas Gorski