Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and a
few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the timings
for the NAND flash on the Nokia N900 that regressed a while ago after
the move to configuring them from DT. Some other OMAPs now set the
correct dma limits on the L3 bus, and a regression fix addresses lost
Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel
power supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC,
this is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data when
mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver
-----BEGIN PGP SIGNATURE-----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=31+Z
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT and driver fixes from Arnd Bergmann:
"For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and
a few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the
timings for the NAND flash on the Nokia N900 that regressed a while
ago after the move to configuring them from DT. Some other OMAPs
now set the correct dma limits on the L3 bus, and a regression fix
addresses lost Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel power
supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC, this
is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data
when mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver"
* tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: chipid: Fix return value on non-Exynos platforms
arm64: dts: Fix leftover entry-methods for PSCI
ARM: dts: exynos: Fix regulator node aliasing on Midas-based boards
ARM: dts: oxnas: Fix clear-mask property
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
soc: fsl: dpio: register dpio irq handlers after dpio create
tee: amdtee: out of bounds read in find_session()
ARM: dts: N900: fix onenand timings
bus: ti-sysc: Fix quirk flags for lcdc on am335x
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
...
These two device trees were either missed or added after
the commit correcting the "entry-method" from
"arm,psci" to just "psci" as per the binding.
Link: https://lore.kernel.org/r/20200322115846.16265-1-linus.walleij@linaro.org
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c4 ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe5 ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the felix switch by default and enable it per board which are
actually using it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that there is support for the Felix switch this variant can also be
added. It features two external ports ethernet ports which are connected
to the internal switch core. No direct connection to any of the enetc's
is supported.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The KBox A-230-LS supports four external ports which are connected to
the internal switch of the LS1028A via QSGMII. Now that the Felix switch
is supported, add these ports in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The module itself has another EEPROM at 50h on I2C4. The EEPROM on the
carriers is located at 57h on I2C3. Fix that in the device trees.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a SPI flash on this carrier connected to the third DSPI
controller. Add it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc fsl,aips-bus.yaml, compatible and reg is
required. And for reg, the AIPS configuration space should be
used, not all the AIPS bus space.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200307091302.14881-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MQ Phanbell board uses Realtek RTL8211FD as Ethernet PHY.
Its datasheet states that the proper post reset duration should be at least 50 ms.
Fixes: f34d4bfab3 ("arm64: dts: imx8mq-phanbell: Add support for ethernet")
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull in downstream patch from NXP repository to enable fspi device.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto child nodes should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update fspi node compatibles of LX2160A-RDB to "jedec,spi-nor" for
automatic detection of flash.
This also helps in fixing below warning:
spi-nor spi0.0: found mt35xu512aba, expected m25p80
spi-nor spi0.1: found mt35xu512aba, expected m25p80
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the iommu-map property to the pci nodes so that the firmware
fixes it up with the required values thus enabling iommu for
devices connected over pci.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IMU chip on the librem5-devkit is not mounted at the "natural" place
that would match normal phone orientation (see the documentation for the
details about what that is).
Since the lsm9ds1 driver supports providing a mount matrix, we can describe
the orientation on the board in the dts:
Create a right-handed coordinate system (x * -1; see the datasheet for the
axis) and rotate 180 degrees around the y axis because the device sits on
the back side from the display.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The poly fuses can handle 6V 4Amps so incease the kernel limts to 5V
3.5Amps.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By adding broken-cd to the usdhc2 stanza the Redpine card can be
detected when the HKS is turned off and on.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify which regulator is used for cpufreq DVFS.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the WoWWAN signal to a gpio key to wake up the system from suspend.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the simcom SIM7100 modem and the sai6 interface that connects it.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the sgtl5000 of the librem 5 devkit in devicetree.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds 4 eeprom support on i2c mux channel #0 -
1. Bootable 512Kbit eeprom at address 0x50.
2. Memory SO-DIMMs SPD channels at 0x51 (upper SO-DIMM) and 0x53.
3. 2Kb eeprom at 0x57 will be used by SolidRun to hold manufacturing
data.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LTC3882 regulator so that the hardware monitoring
can be used with this device. This regulator provides the 0.78V
supply for the LX2160A.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX8M SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b9213899d2b0 ("arm64: dts: ls1028a: disable all enetc ports
by default") all the network ports are disabled by default. This makes
sense, but now we have to enable them explicitly in the boards. Do so
for the sl28 module.
Since we are at it. Make sure the second port is only enabled for the
variant 4 of the module. Variant 3 has only one network port.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the switch PHY nodes to the central MDIO controller PCIe endpoint
node on LS1028A (implemented as PF3) so that PHYs are accessible via
MDIO.
Enable SGMII AN on the Felix PCS by telling PHYLINK that the VSC8514
quad PHY is capable of in-band-status.
The PHYs are used in poll mode due to an issue with the interrupt line
on current revisions of the LS1028A-RDB board.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the switch device node, available on PF5, so that the switch port
sub-nodes (net devices) can be linked to corresponding board specific
phy nodes (external ports) or have their link mode defined (internal
ports).
The switch device features 6 ports, 4 with external links and 2
internally facing to the LS1028A SoC and connected via fixed links to 2
internal ENETC Ethernet controller ports.
Add the corresponding ENETC host port device nodes, mapped to PF2 and
PF6 PCIe functions. Since the switch only supports tagging on one CPU
port, only one port pair (swp4, eno2) is enabled by default and the
other, lower speed, port pair is disabled to prevent the PCI core from
probing them. If enabled, swp5 will be a fixed-link slave port.
DSA tagging can also be moved from the swp4-eno2 2.5G port pair to the
1G swp5-eno3 pair by changing the ethernet = <&enetc_port2> phandle to
<&enetc_port3> and moving it under port5, but in that case enetc_port2
should not be disabled, because it is the hardware owner of the Felix
PCS and disabling its memory would result in access faults in the Felix
DSA driver.
All ports are disabled by default, including the CPU port, and need to
be enabled on a per-board basis.
The phy-mode binding of the internal ENETC ports was modified from
"gmii" to "internal" to match the phy-mode of the internal-facing switch
ports connected to them. The ENETC driver does not perform any phy_mode
validation anyway, so the change is only cosmetic. Also, enetc_port2 is
defined as a fixed-link 1000 Mbps port even though it is 2500 Mbps (as
can be seen by the fact that it is connected to mscc_felix_port4). The
fact that it is currently defined as 1000 Mbps is an artifact of its
PHYLIB implementation instead of PHYLINK (the former can't describe a
fixed-link speed higher than what swphy can emulate from the Clause 22
MDIO spec).
The switch's INTB interrupt line signals:
- PTP TX timestamp availability
- TSN Frame Preemption
And don't forget to enable the 4MB BAR4 in the root complex ECAM space,
where the switch registers are mapped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds