Adding the build support required for OMAP5 soc
in to omap2+ config.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the minimal support for OMAP5 evm board
with device tree.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the irq_match arrays and the irq init functions of OMAP 2,3
and 4 based boards out of board-generic.c file and also rename the
irq init function to match the interrupt controller present in
the SOCs.
This is a preparatory patch to add the OMAP5 evm board's irq init
support with device tree.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add OMAP5 SMP boot support using OMAP4 SMP code. The relevant code paths
are runtime checked using cpu id
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP4 and OMAP5 share same WakeupGen IP with below few udpates on OMAP5.
- Additional 32 interrupt support is added w.r.t OMAP4 design.
- The AUX CORE boot registers are now made accessible from non-secure SW.
- SAR offset are changed and PTMSYNC* registers are removed from SAR.
Patch updates the WakeupGen code accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The l3 interconnect ip is same for OMAP4 and OMAP5.
So reuse the l3 error handler error code for OMAP5
as well. Also a few targets has been newly added for
OMAP5. So updating the driver for that here.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
GPMC module is the same as in OMAP4.
Just update the base address and irq number.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the Initialisaton for clocksource and clockevent device
on OMAP5 Socs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP
architecture. It's a dual core SOC with GIC used for interrupt
handling and with an integrated L2 cache controller.
OMAP5432 is another variant of OMAP5430, with a
memory controller supporting DDR3 and SATA.
Patch includes:
- The machine specific headers and sources updates.
- Platform header updates.
- Minimum initialisation support for serial.
- IO table init
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the OMAP5 ES1.0, 2.0 and OMAP5432 cpu revision
detection support.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If provided dt support, then skip add wdt platform device as usual.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently most ads7846 config definitions for OMAP3 series boards have
been moved to common-board-devices.c, and it is transparent for init.
And it's no very proper to do gpio_request based on get_pendown_state
since omap_ads7846_init knows everything about ads7846_config.
So it's more fit to request gpio according to the right gpio_pendown
and set debounce time conditionally. If we don't set proper debouce
time, there are flooded interrupt counters of ads7846 responding to
one time touch on screen, then the driver couldn't work very well.
This patch has been validated on 3530evm.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was chosen by following the trace on the schematic from component U131
and U134 to the CPEN pin on the USB3320 device.
TWL4030.GPIO2-...->(T2_GPIO2_3V3)U131-..>nUSB2_EN-..>U134-..>EXP_nUSB2_1V8
which starts EHCI tranceiver USB3320.
This will set TWL4030.GPIO2 as output pin to drive EHCI tranceiver.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI PHY requires these regulators:
EVM Rev >=E --> VAUX2
EVM Rev < E --> VUSB1V5, VUSB1V8
Adding USB internal LDOs (vusb1v5 & vusb1v8) and VAUX2 to omap3evm
board file. Also removing vaux2_{1/2/3} supplies as they are not
used on omap3 evm.
But we need not to add vaux2 in twl4030_platform_data since it will
be added conditionally.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With omap_hwmod_get_main_clk() now available, this can be passed to
clk_get() to extract the fclk and thus avoid construction of fclk name.
Corrected the timer fck name mis-match between clock44xx_data.c and
omap_hwmod_44xx_data.c. For other platforms this is already taken care.
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ac5b0ea3d (Merge tag 'omap-devel-f-for-3.6'...) had a merge
conflict that somehow got incorrecly resolved in a lossy way for
commit bed9d1bb (ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API).
Fix the issue by applying the missing pieces.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin discovered that commit c8d82ff68f
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3. This prevents device low power
states.
The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active. This in turn prevents the WKUP
clockdomain from transitioning to idle. There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.
It turns out that there is no need to take the 32k sync timer out of
idle. The IP block itself probably does not have any native idle
handling at all, due to its simplicity. Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active. So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.
This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive. If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled. The
WKUP clockdomains on OMAP3/4 are marked with this flag. (On OMAP2xxx,
no OCP header existed on the 32k sync timer.) Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.
Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses. These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource. But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.
Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI. But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.
This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch. Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch. Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.
References:
1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
(SWPU223U), available from:
http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip
2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
(SWPU223U)
3. ibid.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The function __omap2_set_globals() can be common across all
platforms/architectures, even in case of omap4, internally it
calls same set of functions as in __omap2_set_globals() function
(except for sdrc).
This patch adds new config flag SOC_HAS_OMAP2_SDRC to handle sdrc,
so that we can reuse same function across omap2/3/4...
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per recent discussion on the linux-omap list, we are
moving in the direction where, we will have only architecture,
ARCH_OMAP2PLUS and all devices/platforms will be treated
as a SoC underneath.
So the first step in this direction is to adopt this change
for all new devices getting in, converting
cpu_is_am33xx/335x() ==> soc_is_am33xx/335x()
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially, we decided to make am33xx family of device to fall
under omap3 class (cpu_is_omap34xx() = true), since it carries
Cortex-A8 core. But while adding complete baseport support
(like, clock, power and hwmod) support, it is observed that,
we are creating more and more problems by treating am33xx device
as omap3 family, as nothing matches between them
(except cortex-A8 mpu).
So, after long discussion we have came to the conclusion that,
we should not consider am33xx device as omap3 family, instead
create separate class (SOC_AM33XX) under OMAP2PLUS.
This means, for am33xx device, cpu_is_omap34xx() will return false,
and only cpu_is_am33xx() will be true.
Please refer to the link below, for mailing-list discussion on this -
http://www.spinics.net/lists/linux-omap/msg69439.html
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed typo, updated for soc_is changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to remove unnecessary idefs, move noncore and core
dpll ops to dpll3xxx.c file (where it should have been already).
The clkops (clkops_omap3_core_dpll_ops & clkops_omap3_noncore_dpll_ops)
is used in clock data files, and dependency is already handled by
Makefile rule.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sy5d
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-f-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-part2
Miscellaneous OMAP clock, hwmod, clockdomain, and powerdomain patches
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
arch/arm/plat-omap/include/plat/omap_hwmod.h
management and McBSP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GhIQ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-b-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
A few more OMAP fixes for 3.5-rc. These fix some bugs with power
management and McBSP.
The commit 503d0ea24d
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some prm and cm registers read/write and status functions
are built only for some custom OMAP2+ builds and are stubbed
in header files for other builds under ifdef statements.
But this results in adding new CONFIG_ARCH_OMAPXXX
checks when SOCs are added in the future. So move them
to a common place for OMAP2+ and make them 'weak' implementations.
This way no new ifdefs would be required in the future and also
cleans up the existing code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
[paul@pwsan.com: unsplit quoted strings; moved PRM functions to
mach-omap2/prm_common.c; resolved sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add an API to get main clock name associated with a given @oh.
This will avoid the need to construct fclk names during early
initialization in order to get fclk handle using clk_get().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If the dpll is already locked, code can be optimized
to return much earlier than doing redundent set of lock mode
and wait on idlest.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register is used to configure the behaviour of the CSI-2 and CCP-2
receivers. This register is available only in OMAP3630.
The original patch was submitted by Vimarsh Zutshi.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The wake-up power domain is an alway-on power domain and so this power domain
does not have a power state status (PM_PWSTST_xxx) register that indicates the
current state. However, during the registering of the wake-up power domain the
state of the domain is queried by calling pwrdm_read_pwrst(). This actually
tries to read a register that does not exist and returns a value of 0 that
indicates that the current state is OFF. The OFF state count of the wake-up
power domain is then set to 1 and the current state to OFF. Both of which are
incorrect.
To fix this, if a power domain only supports the ON state, do not attempt to
read the power state status register and simply return ON as the current power
state.
This is based upon Tony's current linux-omap master branch.
Testing:
- Boot tested on OMAP4460 panda.
- Boot tested on OMAP3430 beagle and validated CORE RET still working (using
Paul's 32k timer patch [1]).
[1] http://marc.info/?l=linux-omap&m=134000053229888&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP3+ devices, the clock domains (CLKDMs) support one or more of the
following transition modes ...
NO_SLEEP (0x0) - A clock domain sleep transition is never initiated,
irrespective of the hardware conditions.
SW_SLEEP (0x1) - A software-forced sleep transition. The transition is initiated
when the associated hardware conditions are satisfied
SW_WKUP (0x2) - A software-forced clock domain wake-up transition is initiated,
irrespective of the hardware conditions.
HW_AUTO (0x3) - Hardware-controlled automatic sleep and wake-up transition is
initiated by the PRCM module when the associated hardware
conditions are satisfied.
For OMAP4 devices, SW_SLEEP is equivalent to HW_AUTO and NO_SLEEP is equivalent
to SW_WKUP. The only difference between HW_AUTO and SW_SLEEP for OMAP4 devices
is that the PRM_IRQSTATUS_MPU.TRANSITION_ST interrupt status is set in case of
SW_SLEEP transition, and not set in case of HW_AUTO transition.
For OMAP4 devices, all CLKDMs support HW_AUTO and therefore we can place the
CLKDMs in the HW_AUTO state instead of the SW_SLEEP mode. Hence, we do not
need to use the SW_SLEEP mode. With regard to NO_SLEEP and SW_WKUP it is
preferred to use SW_WKUP mode if the CLKDM supports it and so use this mode
instead of NO_SLEEP where possible.
For a software perspective the above 4 modes are represented by the following
flags to indicate what modes are supported by each of the CLKDMs.
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> SW_SLEEP
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
By eliminating the SW_SLEEP mode the the mapping of the flags for OMAP4 devices
can becomes ...
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> HW_AUTO
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A9qD
-----END PGP SIGNATURE-----
mergetag object c59b537d87
type commit
tag omap-devel-dmtimer-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341130362 -0700
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
mergetag object 6fd8246b1c
type commit
tag omap-devel-am33xx-for-v3.6
tagger Tony Lindgren <tony@atomide.com> 1341131157 -0700
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bc0b
-----END PGP SIGNATURE-----
Merge tags 'omap-cleanup-for-v3.6', 'omap-devel-dmtimer-for-v3.6' and 'omap-devel-am33xx-for-v3.6' into devel-am33xx-part2
clock, power, and voltagedomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP8Am6AAoJEBvUPslcq6VzhVsP/31PxWaX0JboIbAP0VlmJ+GK
J9gIxs2ohx3fDcx4D3da7rLlDue4E0oKmftbj0G4Iom22si2HrtmCnkq41anOkDA
UA9hW8kYfQJr90BzHYuIvOncpb6w6mzjJu7QDSO3j2l1FssoG+rOcDrW0EUSdzhF
1pIaGairntUAsI/EE3Ja6r0reRgacV4CmWksatp3mzxpbyA2+m2zJj8IovY1ghPZ
jq3zcLm4LCxDyiCDYcz6Jrt9fH9OA2cEQ/q0gHKspHvr2lsRu7gzN5gvi+700oML
vIT42/rC6tppf72113arZ+vKluJfa9LhgD0G7JcDqCyRxmwe0w3cKZKWrVklolsZ
sHATYxliWk4gB+pipw8W/hEHKGKPgPEPEAd60RN3g3/SDBo/fcQKvsF5/sZldC70
ngagTSseCKGUOQxWJ1+eRqG+I5WIzgorunNIbN/N9dGyxQ3C+zDAgDbdar24sWFn
1bA1wH7iwEYaqGOCEKfwodl+tSGAeuVXm4e2fR81sHRYY6eIFCKCdExZ/DPJrFTt
FnbV2OgKKz9xYcw6MNmfVEk3TkMSNwFO+g+EtzM1km5oW6PIxkGoiDydxHGvN3fq
gWfv7Y7AJCnbiqKBSahE1WkVADXYTlXk1ySzjHluPXJmqh/iUYDmpKKMYEFQYgyg
ekpI3teAadGhu5ZIrqG5
=bc0b
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
* tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP AM33xx: clockdomains: Add clockdomain data and respective operations
ARM: OMAP AM33xx: powerdomains: add AM335x support
ARM: OMAP AM33xx: CM: Introduce AM33xx CM APIs and register level details
ARM: OMAP AM33xx: PRM: add PRM support
ARM: OMAP AM33xx: voltagedomain: Add voltage domain data
ARM: OMAP2+: control: Add AM33XX control reg & sec clkctrl offset
ARM: OMAP2+: am33xx: Add AM335XEVM machine support
ARM: OMAP2+: am33xx: Add low level debugging support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
code for wake-ups, and improve idle latencies for cpuidle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7qEs
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-pm-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm
From: Tony Lindgren <tony@atomide.com>:
Here are some omap PM changes that reimplement omap PRCM I/O chain
code for wake-ups, and improve idle latencies for cpuidle.
* tag 'omap-devel-pm-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=L0+0
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/timer
From Tony Lindgren <tony@atomide.com>:
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
* tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=A9qD
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren <tony@atomide.com>
Here is some more omap clean-up. The biggest changes are
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
* tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: hwmod: remove prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain
ARM: OMAP3: Move McBSP fck clock alias to hwmod data
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2430
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2420
ARM: OMAP: dsp: interface to control module functions
ARM: OMAP2+: control: new APIs to configure boot address and mode
ARM: OMAP2+: CLEANUP: Remove ARCH_OMAPx ifdef from struct dpll_data
ARM: OMAP2+: hwmod: use init-time function pointer for _init_clkdm
ARM: OMAP2+: hwmod: use init-time function pointer for hardreset
ARM: OMAP2+: hwmod: use init-time function pointer for wait_target_ready
ARM: OMAP4: hwmod: drop extra cpu_is check from _wait_target_disable()
ARM: OMAP2+: hwmod: use init-time function ptrs for enable/disable module
ARM: OMAP4: hwmod: rename _enable_module to _omap4_enable_module()
ARM: OMAP: Make FS USB omap1 only
ARM: OMAP2: Remove legacy USB FS support
ARM: OMAP3: There is no FS USB controller on omap3
ARM: OMAP: dma: Clear status registers on enable/disable irq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
critical enough for the 3.5 -rc cycle. The biggest changes are
fixes for the am35xx clock and hwmod data, and the removal of dead
code for the 730 and 850 headers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UD1/
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-non-critical-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren <tony@atomide.com>:
This branch contains fixes that were too intrusive or not
critical enough for the 3.5 -rc cycle. The biggest changes are
fixes for the am35xx clock and hwmod data, and the removal of dead
code for the 730 and 850 headers.
* tag 'omap-fixes-non-critical-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
mfd: twl: remove pdata->irq_base/_end, no more users
ARM: OMAP2+: TWL: remove usage of pdata->irq_base/_end
ARM: OMAP2+: OPP: Fix to ensure check of right oppdef after bad one
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC. Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.
Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register the tvp5150 video decoder in ISP subsystem.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup pinmux for CPI and register the mt9t001 camera sensor
in ISP subsystem.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register OMAP DRM/KMS platform device. DMM is split into a
separate device using hwmod.
Signed-off-by: Andy Gross <andy.gross@ti.com>
Signed-off-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM33XX clock implementation is different than any existing OMAP
family of devices. Although DPLL module is similar to OMAP4
device, but the usage is very much different than OMAP4.
AM33XX has different peripheral set and each module gets
integrated to the clock framework differently than OMAP
family of devices.
This patch adds full Clock tree data for AM33XX family
of devices and also integrates it into existing OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply; changed 'soc_is_am33xx' to
'cpu_is_am33xx' to match usage in Tony's current am33xx branch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
commit 99b59df0 (ARM: OMAP3: PM: fix shared PRCM interrupt leave
disabled at boot) added IRQ_NOAUTOEN to the PRCM interrupt so it could
be enabled later if needed. However, this commit was partially undone
when merging the IO daisy chain rework in 9a17d88e (Merge tag
'omap-devel-c-for-3.6' of
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into
devel-pm
This patch adds back the IRQ_NOAUTOEN fix that was removed by the
merge resolution.
This also fixes the following boot-time warning that showed up after
merging the IO daisy chain rework:
[ 3.849334] WARNING: at kernel/irq/manage.c:436 enable_irq+0x3c/0x78()
[ 3.856231] Unbalanced enable for IRQ 297
[ 3.860473] Modules linked in:
[ 3.863739] [<c001a114>] (unwind_backtrace+0x0/0xf0) from [<c003c7e8>] (warn_slowpath_common+0x4c/0x64)
[ 3.873687] [<c003c7e8>] (warn_slowpath_common+0x4c/0x64) from [<c003c894>] (warn_slowpath_fmt+0x30/0x40)
[ 3.883819] [<c003c894>] (warn_slowpath_fmt+0x30/0x40) from [<c00993e0>] (enable_irq+0x3c/0x78)
[ 3.893035] [<c00993e0>] (enable_irq+0x3c/0x78) from [<c067b1e8>] (omap3_pm_init+0x328/0x5f4)
[ 3.902099] [<c067b1e8>] (omap3_pm_init+0x328/0x5f4) from [<c067161c>] (init_machine_late+0x1c/0x28)
[ 3.911773] [<c067161c>] (init_machine_late+0x1c/0x28) from [<c0008648>] (do_one_initcall+0x34/0x178)
[ 3.921539] [<c0008648>] (do_one_initcall+0x34/0x178) from [<c066e8f4>] (kernel_init+0xfc/0x1c0)
[ 3.930847] [<c066e8f4>] (kernel_init+0xfc/0x1c0) from [<c00140b0>] (kernel_thread_exit+0x0/0x8)
[ 3.940246] ---[ end trace 55a0ad32ca2ca682 ]---
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
commit 164e0cbf60 (ARM: OMAP3/4: consolidate cpuidle Makefile) added
an OMAP-specific dependency from CPU_IDLE to CONFIG_PM. This causes
some randconfig warnings when CONFIG_PM has unmet dependencies:
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
Fix this by making the dependency on CONFIG_PM_RUNTIME (which in turn
will enable CONFIG_PM.)
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dispc_disable_outputs() function currently disables all LCD managers except
LCD3. This patch adds disabling functionality for LCD3 manager thereby
maintaining consistency of Display Subsystem for in case Display Controller is
reset when LCD3 manager is in use.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Using nr_irqs as local variable name triggers the sparse warning..
./arch/arm/mach-omap2/irq.c:265:6: warning: symbol 'nr_irqs' shadows an earlier one
./linux/include/linux/irqnr.h:26:12: originally declared here
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am35x family of SoCs only support the PWRSTS_ON
state so create a new set of powerdomain structures
that ensure that only the ON state is entered.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
The am35x family of SoCs do not have an IVA so
a parallel set of clockdomain dependencies are
required that are simililar to OMAP3 but without
any IVA dependencies.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support for the EMAC (and MDIO)
ethernet controller that's on the am35x
family of SoC's.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated subject line; updated to apply on v3.5-rc4;
added comments to hwmod data regarding IPSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
During kernel init, the AM3505/AM3517 UART4 cannot complete its softreset:
omap_hwmod: uart4: softreset failed (waited 10000 usec)
This also results in another warning later in the boot process:
omap_hwmod: uart4: enabled state can only be entered from initialized, idle, or disabled state
From empirical observation, the AM35xx UART4 IP block requires either
uart1_fck or uart2_fck to be enabled while UART4 resets. Otherwise
the reset will never complete. So this patch adds uart1_fck as an
optional clock for UART4 and adds the appropriate hwmod flag to cause
uart1_fck to be enabled during the reset process. (The choice of
uart1_fck over uart2_fck was arbitrary.)
Unfortunately this observation raises many questions. Is it necessary
for uart1_fck or uart2_fck to be controlled with uart4_fck for the
UART4 to work correctly? What exactly do the AM35xx UART4 clock
tree and the related PRCM idle management FSMs look like? If anyone
has the ability to answer these questions through empirical functional
testing, or hardware information from the AM35xx designers, it would
be greatly appreciated.
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Add missing terminators to the arrays of IRQ, DMA, and address space
structure records in the AM35xx UART4 hwmod data. Without these
terminators, the following warnings appear on boot:
omap_uart.3: failed to claim resource 58
omap_device: omap_uart: build failed (-16)
WARNING: at /home/paul/linux/arch/arm/mach-omap2/serial.c:375 omap_serial_init_port+0x198/0x284()
Could not build omap_device for omap_uart: uart4.
Also, AM35xx uart4_fck has an incorrect parent clock pointer. Fix it
and clean up a whitespace issue.
Fix some incorrectly-named macros related to AM35xx UART4.
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Partially fix the hwmod data for the AM35xx USB OTG hwmod. This
should resolve the following boot warning on AM35xx platforms:
omap_hwmod: am35x_otg_hs: cannot be enabled for reset (3)
While here, also fix the clkdev records, to avoid warnings about
duplicate clock aliases.
The hwmod is also connected to the wrong interconnect. It should be
connected to the IPSS, not the L4 CORE. But that is left for a future
fix, since it probably has a dependency on some hwmod core changes.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Hema HK <hemahk@ti.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3, OMAP4 and AM33xx share some common data like, clksel_rate
oscillator clock input (Virtual clock nodes), required for
clock tree; so move common data to common data file so that it
can be reused.
[hvaibhav@ti.com: Created separate commit from Paul's developement
branch]
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
an oops on boot for all omap3xxx platforms that use usbhs_omap for
EHCI. The actual oops comes from faulty ehci-omap cleanup, but the
failure caused by the change is evidenced here:
[ 3.655059] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
[ 3.661376] ehci-omap: probe of ehci-omap.0 failed with error -2
utmi_p1_gfclk is a clock that exists on OMAP4, but not OMAP3. In the
OMAP3 case, it is configured as a dummy clock. However, OMAP4 lists
the dev_id as NULL, but OMAP3 lists it as "usbhs_omap".
Attempting to get that clock from ehci-omap then fails. The solution
is to just change the clock3xxx_data.c for dummy clocks used in the
errata fix to match the dev_id, NULL, used in clock44xx_data.c.
Tested on BB-xM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled. By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2
Fix this by removing the duplicate dummy entry from the C file.
Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Also note that we need to only build this code if MMC_OMAP
is selected, so change Makefile accordingly and place it near
the MMC_OMAP_HS in the Makefile.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For a power domain to idle all the clock domains in it must idle.
This patch implements an optimization of the cpuidle code by
denying and later allowing only the first registered clock domain
of a power domain, and so optimizes the latency of the low power code.
The functions _cpuidle_allow_idle and _cpuidle_deny_idle are
not used anymore and so are removed.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
One of the main contributors of the low power code latency is
the PER power domain. To optimize the high-performance and
low-latency C1 state, prevent any PER state which is lower
than the CORE state in C1.
Reported and suggested by Kevin Hilman.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
If the next state is no found in the next_valid_state function,
fallback to the default value of C1 (which is state 0).
This prevents the use of a bogus state -1 in the rest of the cpuidle
code.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit e7410cf7 (OMAP3: PM: move device-specific special cases from PM
core into CPUidle) moved mangement of cam_pwrdm to CPUidle but left
some remnants behind, namely the call to clkcm_allo_idle() for the
clockdomains in the MPU pwrdm. Remove these since they are not
necessary and cause unwanted latency in the idle path.
Acked-by: Tero Kristo <Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We only need to call the pre/post transtion methods when we know the
power state is changing. First, split up the pre/post transition
calls to be per-powerdomain, and then make them conditional on whether
the power domain is actually changing states.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Iteration over all power domains in the idle path is unnecessary since
only power domains that are transitioning need to be accounted for.
Also PRCM register accesses are known to be expensive, so the
additional latency added to the idle path is signficiant.
In order allow the pre/post transitions to be isolated and called
per-pwrdm, change the API so passing in a specific power domain will
trigger the pre/post transtion accounting for only that specific power
domain. Passing NULL means iterating over all power domains as is
current behavior.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
all OMAP2+ chips that appear to have it integrated. Fix a problem
preventing it from being used on OMAP4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Fpsi
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-b-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-driver
Convert the OMAP HDQ1W driver to use runtime PM. Make it available on
all OMAP2+ chips that appear to have it integrated. Fix a problem
preventing it from being used on OMAP4.
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cMPJ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
As IO Daisy chain sequence is triggered via hwmod mux, there is no need to
control it from cpuidle path for OMAP3.
Also as omap3_disable_io_chain is no longer being used, just remove the
function.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
IO Daisychain feature has to be triggered whenever there is a change in
device's mux configuration (See section 3.9.4 in OMAP4 Public TRM vP).
Now devices can idle independent of the powerdomain, there can be a
window where device is idled and corresponding powerdomain can be
ON/INACTIVE state. In such situations, since both module wake up is
enabled at padlevel as well as io daisychain sequence is triggered,
there will be 2 PRCM interrupts (Module async wake up via swakeup and
IO Pad interrupt). But as PRCM Interrupt handler clears the Module
Padlevel WKST bit in the first interrupt, module specific interrupt
handler will not triggered for the second time
Also look at detailed explanation given by Rajendra at
http://www.spinics.net/lists/linux-serial/msg04480.html
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: remove dependency on pm.c & pm.h; add kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable IO Wake up for OMAP3/4 as part of PRM Init. Currently this has been
managed in cpuidle path which is not the right place. Subsequent patch
will remove IO Daisy chain handling in cpuidle path once daisy chain is
handled as part of hwmod mux. This patch also moves the OMAP4 IO wakeup
enable code from the trigger function to init time setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: harmonize function names with other PRM functions; add
kerneldoc; resolve checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
IO daisychain is a mechanism that allows individual IO pads to generate
wakeup events on their own based on a switch of an input signal level.
This allows the hardware module behind the pad to be powered down, but
still have device level capability to detect IO events, and once this
happens the module can be powered back up to resume IO. See section
3.9.4 in OMAP4430 Public TRM for details.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: use the shared MAX_IOPAD_LATCH_TIME declaration; renamed
omap4_trigger_io_chain() to conform to other PRM function names;
added kerneldoc; resolved checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since IO Daisychain modifies only PRM registers, it makes sense to move
it to PRM File. Also changed the timeout value for IO chain enable to
100us and added a wait for status disable at the end.
Thanks to Nishanth Menon <nm@ti.com> for contributing a fix to the
timeout code waiting for WUCLKOUT to go high.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: renamed omap3_trigger_io_chain() to better describe the
end result and to match other PRM functions; removed
omap3_disable_io_chain(); moved MAX_IOPAD_LATCH_TIME to prcm-common as it
will also be used by the OMAP4 code; removed unnecessary barrier;
added kerneldoc; added credit for fix from Nishanth]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently the enabling and disabling of IO Daisy chain is not
according to the TRM. The below steps are followed to enable/
disable the IO chain, based loosely on the "Sec 3.5.7.2.2
I/O Wake-Up Mechanism" section in OMAP3630 Public TRM[1].
Steps to enable IO chain:
[a] Set PM_WKEN_WKUP.EN_IO bit
[b] Set the PM_WKEN_WKUP.EN_IO_CHAIN bit
[c] Poll for PM_WKST_WKUP.ST_IO_CHAIN.
[d] When ST_IO_CHAIN bit set to 1, clear PM_WKEN_WKUP.EN_IO_CHAIN
[e] Clear ST_IO_CHAIN bit.
Steps to disable IO chain:
[a] Clear PM_WKEN_WKUP.EN_IO_CHAIN bit
[b] Clear PM_WKEN_WKUP.EN_IO bit
[c] Clear PM_WKST_WKUP.ST_IO bit by writing 1 to it.
Step [e] & [c] in each case can be skipped, as these are handled
by the PRCM interrupt handler later.
[1] http://focus.ti.com/pdfs/wtbu/OMAP36xx_ES1.x_PUBLIC_TRM_vV.zip
Signed-off-by: Mohan V <mohanv@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: modified commit message to clarify that these steps are
based loosely on the TRM section, rather than documented exactly]
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: resolved new warnings from checkpatch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP4 only builds, the omap2_prm_* functions have dummy wrappers
to detect incorrect usage. However, several unrelated omap3 PRM
functions have made it inside the #else clause of the #ifdef wrapping
the omap2_prm stubs, causing them to disappear on OMAP4-only builds.
This was unnoticed until the IO chain support was added and introduced
a new function in this section which is referenced by omap_hwmod.c:
arch/arm/mach-omap2/omap_hwmod.c: In function '_reconfigure_io_chain':
arch/arm/mach-omap2/omap_hwmod.c:1665:3: error: implicit declaration of function 'omap3xxx_prm_reconfigure_io_chain' [-Werror=implicit-function-declaration]
Fix by using the #ifdef to only wrap the omap2_prm functions that
need stubs on OMAP4-only builds.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: fixed checkpatch warnings for patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the old-style device registration code for HDQ1W to use
omap_device. This will allow the driver to be converted to use PM
runtime and to take advantage of the OMAP IP block management
infrastructure (hwmod, PM, etc.).
A side benefit of this conversion is that it also makes the HDQ device
available on OMAP2420. The previous code only enabled it on 2430 and
3430.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit bbd707acee ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:
arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?
Fix by including the header file containing the prototype.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.
This is the second of two patches needed to resolve the following
boot warning:
omap_hwmod: usb_host_fs: _wait_target_disable failed
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it. This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:
omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The beagleboard USB Host Port that is used is Port 2. The platform driver
sets MODE_PHY for port 1 causing pin muxing to override the pins on the
expansion connector P17 when using board_mux[]. Since USBHS Port 1 is not
connected remove the case for muxing the USB Port1 pins by default.
Tested with BeagleBoard xM revC and checked the userguides for Beagle xM
and revC to be sure USB Port2 is what is used.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the kernel is built only for OMAP2 the following warning will show up:
arch/arm/mach-omap2/twl-common.c:52: warning: ‘twl_set_voltage’ defined but not used
arch/arm/mach-omap2/twl-common.c:58: warning: ‘twl_get_voltage’ defined but not used
The twl_set/get_voltage callbacks only used when OMAP3/4 is selected.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case a board provides the gpio_pendown and not board_pdata,
the GPIO debounce is not taken care of.
Fix this by taking care of GPIO debounce in any case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e813a55eb9 ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.
This patch removes several boot errors from board-omap3beagle.c:
- gpio_request: gpio--22 (DVI reset) status -22
- Unable to get DVI reset GPIO
There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.
For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.
For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.
Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.
Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.
Fix the situation for omaps. The following users should fix the
platform init code in a similar way:
Dropped Kconfig option Current users
USB_MUSB_OTG blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL davinci, not in Kconfigs
USB_MUSB_HOST davinci, not in Kconfigs
USB_MUSB_HDRC_HCD blackfin, not in Kconfigs
USB_MUSB_OTG blackfin, not in Kconfigs
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TWL driver has been converted to use SPARSE_IRQ and no longer
needs to be passed IRQ base/end. Since driver no longer uses these
fields, so remove them from the reamaining users.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 9fa2df6b90
(ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present)
makes the logic:
for (i = 0; i < opp_def_size; i++) {
<snip>
if (!oh || !oh->od) {
<snip>
continue;
}
<snip>
opp_def++;
}
In short, the moment we hit a "Bad OPP", we end up looping the list
comparing against the bad opp definition pointer for the rest of the
iteration count. Instead, increment opp_def in the for loop itself
and allow continue to be used in code without much thought so that
we check the next set of OPP definition pointers :)
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current Makefile compiles the cpuidle34xx.c and cpuidle44xx.c files
even if the cpuidle option is not set in the kernel.
This patch fixes this by creating a section in the Makefile where these
files are compiled only if the CONFIG_CPU_IDLE option is set.
This modification breaks an implicit dependency between CPU_IDLE and PM as
they belong to the same block in the Makefile. This is fixed in the Kconfig
by selecting explicitely PM is CPU_IDLE is set.
The linux coding style recommend to use no-op functions in the headers
when the subsystem is disabled instead of adding big section in C files.
This patch fix this also.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
prcm_setup_regs() blindly accesses IVA bits
in the PRM and calls omap3_iva_idle() which
does more IVA related register accesses.
Only do this if the IVA hardware actually
exists.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove prm_clkdm and cm_clkdm and allow hwmods to have no clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Provide an interface for a driver to call SCM functions to
set a boot address and boot mode.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
SCM contains boot addr and boot mode registers to control
other processors on different OMAP versions. It controls the
boot address and mode for DSP based subsystems like: IVA 2.1
(OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4).
If contained within SCM registers, when a processor is
booting it uses BOOTADDR to start running the code at that
location. BOOTMOD register specifies a different set of
modes for the processor to execute when booting (from direct,
idle, self-loop, user and default).
Since there was no offset associated with OMAP4, this patch
defines it.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rather than use runtime cpu_is* checking inside _init_clkdm, initialize
SoC specific function pointer at init time.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: convert to use soc_ops function pointers; remove second para
from commit message since soc_ops function pointers are now set during hwmod
layer init]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rather than using cpu_is* checking at runtime, initialize SoC specific
function pointers for the various hard reset functions at init time.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: convert to use soc_ops function pointers; add kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rather than using cpu_is* checking at runtime, initialize an SoC specific
function pointer for wait_target_ready().
While here, downgrade the BUG() to a WARN_ON() so it gives a noisy
warning instead of causing a kernel panic.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: convert to use soc_ops function pointers; add kerneldoc;
move soc_ops functions to their own section in the code; integrated
the _wait_target_ready() function with the OMAP2/OMAP4 variants;
renamed the wait_module_ready field to wait_target_ready]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_omap4_wait_target_disable() is called only from inside _omap4_disable_module()
which is already protected by SoC specific checks. Remove the cpu_is check
here.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM. Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.
NOTE: the cpu_is* check for _enable_module was different than
the one for _disable_module, and this patch uses
cpu_is_omap44xx() for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_enable_module is specific to SoCs with PRCM interfaces similar to
that of the OMAP4, so rename it to be consistent with the
corresponding _omap4_disable_module.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: tweaked commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM33XX PRCM module consists of various clockdomains, in all
total we have 18 clockdomains available, with following
controlling options,
- SW Sleep: sw forced sleep transition
- SW Wakeup: sw forced wakeup transition
This patch adds all available clockdomain data, respective
clockdomain operations for AM33XX family of device, and also
integrates it into existing OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: removed CLKDM_NO_AUTODEPS from clockdomain flags, removed
unnecessary .clktrctrl_offs field; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add offset & mask fields to struct powerdomain
In case of AM33xx family of devices, there is no consistency between
PWRSTCTRL & PWRSTST register offsers in PRM space, for example -
PRM_XXX PWRSTCTRL PWRSTST
=======================================
PRM_PER_MOD: 0x0C, 0x08
PRM_WKUP_MOD: 0x04, 0x08
PRM_MPU_MOD: 0x00, 0x04
PRM_DEVICE_MOD: NA, NA
And also, there is no consistency between bit-offsets inside
PWRSTCTRL & PWRSTST register, for example -
PRM_XXX LOGICRET MEMON MEMRET
=======================================
GFX_PWRCTRL: 2, 17, 6
PER_PWRCTRL: 3, 25, 29
MPU_PWRCTRL: 2, 18, 22
WKUP_PWRCTRL: 3, NA, NA
This means, we need to maintain and pass on all this information
in powerdomain handle; so adding fields for,
- PWRSTCTRL/ST register offset
- Logic retention state mask
- mem_on/ret/pwrst/retst mask
Currently, this fields is only applicable and used for AM33XX devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: this patch is a combination of "Add offset & mask fields to
struct powerdomain" and the powerdomain portions of "ARM: OMAP3+: am33xx:
Add powerdomain & PRM support"; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As far as PRM/CM/PRCM modules are concerned, AM33XX device is
different than OMAP3 and OMAP4 architectures; so similar to
PRM implementation, handle AM33XX CM separately.
This patch introduces AM33XX CM module low-level api's, used and
required by omap clockdomain and hwmod framework.
Please note that cm-regbits-33xx.h (register bit field offset)
and cm33xx.h (register addr offset) files are mostly auto generated.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split the hwmod code changes in this patch into a separate
patch; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As far as PRM/CM/PRCM modules are concerned, AM33XX device is
different than OMAP3 and OMAP4 architectures; so we need to handle it
separately. This patch adds support for the PRM APIs required for
AM33XX device.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: separated the PRM parts of "ARM: OMAP3+: am33xx: Add
powerdomain & PRM support" into this patch; fixed Makefile prm33xx.o
location; cleaned up some checkpatch violations; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently dummy voltage domain data is being created
in order to succeed boot process, nothing has been done
w.r.t actual hardware (voltage control).
Also, hook up the AM33XX voltage domain to OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define AM33XX control register, in order to allow access to
control register address space, also add CONTROL_SEC_CLK_CTRL
register offset; both are required in clock tree data,
for wdt0 and timer0 clock source select configuration.
CONTROL.SEC_CLK_CTRL register is provided to select/configure
clock input for WDT0 and TIMER0.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: added include of plat/am33xx.h to fix build break;
added AM33XX_CONTROL_STATUS bitfields that will be needed for the clock
tree; fixed some control.h whitespace problems while here]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A bit larger set than usual, unfortunately -- I've been sitting on them
longer than I meant to so it's really more like 2 -rc pull requests in
one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement patch,
but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=x9VX
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bit larger set than usual, unfortunately -- I've been sitting on
them longer than I meant to so it's really more like 2 -rc pull
requests in one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement
patch, but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: Kirkwood: Fix clk problems modular ethernet driver
arm: versatile: fix and enable PCI I/O space
ARM: highbank: Add smc calls to enable/disable the L2
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
...
The OMAP dmtimer driver allows you to dynamically configure the functional
clock that drives the timer logic. The dmtimer driver uses the device name and
a "con-id" string to search for the appropriate functional clock.
Currently, we define a clock alias for each functional clock source each timer
supports. Some functional clock sources are common to all of the timers on a
device and so for these clock sources we can use a single alias with a unique
con-id string.
The possible functional clock sources for an OMAP device are a 32kHz clock,
a system (MHz range) clock and (for OMAP2 only) an external clock. By defining
a unique con-id name for each of these (timer_32k_ck, timer_sys_ck and
timer_ext_ck) we can eliminate a lot of the clock aliases for timers. This
reduces code, speeds-up searches and clock initialisation time.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP1 uses an architecture specific function for setting the dmtimer clock
source, where as the OMAP2+ devices use the clock framework. Eventually OMAP1
device should also use the clock framework and hence we should not any
architecture specific functions.
For now move the OMAP2+ function for configuring the clock source into the
dmtimer driver. Therefore, we do no longer need to specify an architecture
specific function for setting the clock source for OMAP2+ devices. This will
simplify device tree migration of the dmtimers for OMAP2+ devices.
From now on, only OMAP1 devices should specify an architecture specific
function for setting the clock source via the platform data set_dmtimer_src()
function pointer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP2+ devices, a function pointer that returns the number of times a timer
power domain has lost context is passed to the dmtimer driver. This function
pointer is only populated for OMAP2+ devices and it is pointing to a platform
function. Given that this is a platform function, we can simplify the code by
removing the function pointer and referencing the function directly. We can use
the OMAP_TIMER_ALWON flag to determine if we need to call this function for
OMAP1 and OMAP2+ devices.
The benefit of this change is the we can remove the function pointer from the
platform data and simplifies the dmtimer migration to device-tree.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data variable loses_context is used to determine if the timer may
lose its logic state during power transitions and so needs to be restored. This
information is also provided in the HWMOD device attributes for OMAP2+ devices
via the OMAP_TIMER_ALWON flag. When this flag is set the timer will not lose
context. So use the HWMOD device attributes to determine this.
For OMAP1 devices, loses_context is never set and so set the OMAP_TIMER_ALWON
flag for OMAP1 timers to ensure that code is equivalent.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the dmtimer determines whether an timer can support an external
clock source (sys_altclk) for driving the timer by the IP version. Only
OMAP24xx devices can support an external clock source, but the IP version
between OMAP24xx and OMAP3xxx is common and so this incorrectly indicates
that OMAP3 devices can use an external clock source.
Rather than use the IP version, just let the clock framework handle this.
If the "alt_ck" does not exist for a timer then the clock framework will fail
to find the clock and hence will return an error. By doing this we can eliminate
the "timer_ip_version" variable passed as part of the platform data and simplify
the code.
We can also remove the timer IP version from the HWMOD data because the dmtimer
driver uses the TIDR register to determine the IP version.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following issues with the timer device attributes for OMAP2+ devices:
1. For OMAP24xx devices, timers 2-8 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 is in an ALWAYS-ON power domain.
2. For OMAP3xxx devices, timers 2-7 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 and timer12 are in an ALWAYS-ON power domain.
3. For OMAP3xxx devices, timer12 does not have the ALWAYS-ON attribute but
is in an always-on power domain.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although the OMAP timers share a common hardware design, there are some
differences between the timer instances in a given device. For example, a timer
maybe in a power domain that can be powered-of, so can lose its logic state and
need restoring where as another may be in power domain that is always be on.
Another example, is a timer may support different clock sources to drive the
timer. This information is passed to the dmtimer via the following platform data
structure.
struct dmtimer_platform_data {
int (*set_timer_src)(struct platform_device *pdev, int source);
int timer_ip_version;
u32 needs_manual_reset:1;
bool loses_context;
int (*get_context_loss_count)(struct device *dev);
};
The above structure uses multiple variables to represent the timer features.
HWMOD also stores the timer capabilities using a bit-mask that represents the
features supported. By using the same format for representing the timer
features in the platform data as used by HWMOD, we can ...
1. Use the flags defined in the plat/dmtimer.h to represent the features
supported.
2. For devices using HWMOD, we can retrieve the features supported from HWMOD.
3. Eventually, simplify the platform data structure to be ...
struct dmtimer_platform_data {
int (*set_timer_src)(struct platform_device *pdev, int source);
u32 timer_capability;
}
Another benefit from doing this, is that it will simplify the migration of the
dmtimer driver to device-tree. For example, in the current OMAP2+ timer code the
"loses_context" variable is configured at runtime by calling an architecture
specific function. For device tree this creates a problem, because we would need
to call the architecture specific function from within the dmtimer driver.
However, such attributes do not need to be queried at runtime and we can look up
the attributes via HWMOD or device-tree.
This changes a new "capability" variable to the platform data and timer
structure so we can start removing and simplifying the platform data structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During early boot, one or two dmtimers are reserved by the kernel as system
timers (for clocksource and clockevents). These timers are marked as reserved
and the dmtimer driver is notified which timers have been reserved via the
platform data information.
For OMAP2+ devices the timers reserved may vary depending on device and compile
flags. Therefore, it is not easy to assume which timers we be reserved for the
system timers. In order to migrate the dmtimer driver to support device-tree we
need a way to pass the timers reserved for system timers to the dmtimer driver.
Using the platform data structure will not work in the same way as it is
currently used because the platform data structure will be stored statically in
the dmtimer itself and the platform data will be selected via the device-tree
match device function (of_match_device).
There are a couple ways to workaround this. One option is to store the system
timers reserved for the kernel in the device-tree and query them on boot.
The downside of this approach is that it adds some delay to parse the DT blob
to search for the system timers. Secondly, for OMAP3 devices we have a
dependency on compile time flags and the device-tree would not be aware of that
kernel compile flags and so we would need to address that.
The second option is to add a function to the dmtimer code to reserved the
system timers during boot and so the dmtimer knows exactly which timers are
being used for system timers. This also allows us to remove the "reserved"
member from the timer platform data. This seemed like the simpler approach and
so was implemented here.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP2+ timer code has a definition for the maximum number of timers that
OMAP2+ devices have. This defintion is not used anywhere in the code and
appears to be left over. Furthermore the definition is not accurate for OMAP4
devices that only have 11 timers available because the 12th timer is reserved
as a secure timer and for OMAP3 devices the 12th timer is not available on
secure devices. Therefore, remove this definition.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yO72
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
Commit 7f28427b (ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2)
moved DSP platform init code, but failed to include memblock.h causing:
arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/mach-omap2/dsp.c:58: error: implicit declaration of function 'arm_memblock_steal'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we will get:
arch/arm/mach-omap2/omap_l3_smx.c: In function ‘omap3_l3_block_irq’:
arch/arm/mach-omap2/omap_l3_smx.c:156: warning: unused variable ‘address’
arch/arm/mach-omap2/omap_l3_smx.c:155: warning: unused variable ‘multi’
arch/arm/mach-omap2/omap_l3_smx.c:154: warning: unused variable ‘initid’
arch/arm/mach-omap2/omap_l3_smx.c:153: warning: unused variable ‘code’
arch/arm/mach-omap2/omap_l3_smx.c: At top level:
arch/arm/mach-omap2/omap_l3_smx.c:68: warning: ‘omap3_l3_code_string’ defined but not used
arch/arm/mach-omap2/omap_l3_smx.c:90: warning: ‘omap3_l3_initiator_string’ defined but not used
Fix it by always showing the L3 error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.
One such crash was reported by John Stultz <johnstul@us.ibm.com>:
[ 18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[ 18.765319] pgd = ea6b8000
[ 18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[ 18.774749] Internal error: Oops: 17 [#1] SMP ARM
[ 18.779663] Modules linked in:
[ 18.782836] CPU: 0 Not tainted (3.5.0-rc1-dirty #456)
[ 18.788482] PC is at _od_resume_noirq+0x1c/0x78
[ 18.793212] LR is at _od_resume_noirq+0x6c/0x78
[ 18.797943] pc : [<c00307ec>] lr : [<c003083c>] psr: 20000113
[ 18.797943] sp : ec3abe80 ip : ec3abdb8 fp : 00000006
[ 18.809936] r10: ec1148b8 r9 : c08a48f0 r8 : c00307d0
[ 18.815368] r7 : 00000000 r6 : 00000000 r5 : ec114800 r4 :
ec114808
[ 18.822174] r3 : 00000000 r2 : 00000000 r1 : ec154fe8 r0 :
00000006
[ 18.829010] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 18.836456] Control: 10c5387d Table: aa6b804a DAC: 00000015
[ 18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[ 18.848358] Stack: (0xec3abe80 to 0xec3ac000)
DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.htmlhttp://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support for AM335X machine init.
During last merge window, two separate patches supporting am33xx
machine init had been submitted,
1. Link to earlier Baseport patch submission (Legacy):
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg59325.html
2. Link to earlier DT based machine init support patch submission:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg61398.html
And both had got accepted at that time, but got missed during
merge window.
But now, since we have taken decision to make am33xx as a separate
class and not to follow omap3 family, these patches needs to changes
accordingly (only changes),
- Combine both the patches, since early init and timer init
used in board-generic.c file requires them.
- Remove dependency on AM3517EVM, and only use DT approach
for machine init.
- Change the config option (as changed recently)
CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for low level debugging on AM335X EVM (AM33XX family).
Currently only support for UART1 console, which is used on AM335X EVM
is added.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer)
added support for lis3lv02d accelerometer.
The patch was still using OMAP_GPIO_IRQ which no longer exists.
Fix it by using gpio_to_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Russell King