Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CfCl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
This commit add support for STMicroelectronics lis2dh12 accelerometer.
Datasheet for this device can be found here:
http://www.st.com/st-web-ui/static/active/en/resource/technical/
document/datasheet/DM00091513.pdf
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This accelerometer accidentally either emits a DRDY signal or an
IRQ signal. Accidentally I activated the IRQ signal as I thought
it was analogous to the interrupt generator on other ST
accelerometers. This was wrong. After this patch generic_buffer
gives a nice stream of accelerometer readings.
Fixes: 3acddf74f8 "iio: st-sensors: add support for lis3lv02d accelerometer"
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the lsm303agr accelerometer.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
This adds support for the LIS331DL sensor version. This is
a simple 8bit-only accelerometer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some sensors like the LIS331DL only support 8bit data by a single
register per axis. These utilize the MSB byte. Make it possible
to register these apropriately.
A oneliner change is needed in the ST sensors core to handle 8bit
reads as this is the first supported 8bit sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the LIS3LV02 accelerometer found in the
ST Microelectronics Nomadik board series.
Cc: devicetree@vger.kernel.org
Cc: Denis CIOCCA <denis.ciocca@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows in kernel client drivers to access this
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Currently the pressure sensor has code to retrieve and enable two
regulators for Vdd and Vdd IO, but actually these voltage inputs
are found on all of these ST sensors, so move the regulator
handling to the core and make sure all the ST sensors call these
functions on probe() and remove() to enable/disable power.
Here also mover over to obtaining the regulator from the *parent*
device of the IIO device, as the IIO device is created on-the-fly
in this very subsystem it very unlikely evert have any regulators
attached to it whatsoever. It is much more likely that the parent
is a platform device, possibly instantiated from a device tree,
which in turn have Vdd and Vdd IO supplied assigned to it.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is pretty helpful to know already from dmesg that a certain
device is successfully registered, instead of having to browse
sysfs to see if it's actually there.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix buffer registration that allows to use generic IIO trigger.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reduce the amount of those unnecessary goto calls, as in most cases
we can simply return immediately. We also only call for the IRQ number
once and use that value throughout.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch add support to redirect the DRDY interrupt on INT1 or INT2
on accelerometer and pressure sensors.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch introduce num_data_channels variable on st_sensors struct
to manage different type of channels (size or number) in
st_sensors_get_buffer_element function.
Removed ST_SENSORS_NUMBER_DATA_CHANNELS and ST_SENSORS_BYTE_FOR_CHANNEL
and used struct iio_chan_spec const *ch to catch data.
Added 3 byte channel data support on one-shot reads.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Partly a case of removing unused headers and partly a case
of ifdefing out the iio_trigger_ops structures. This has
come about because of an 'unusual' separation of code in this
driver.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Greg Kroah-Hartman