We have hit this intermittently, increase the verbosity of
warning message on unexpected mid cancellation.
Signed-off-by: Steve French <stfrench@microsoft.com>
Change these free functions to allow passing NULL as the argument and
treat it as a no-op just like free(NULL) would.
Or, if rqst->rq_iov is NULL.
The second scenario could happen for smb2_queryfs() if the call
to SMB2_query_info_init() fails and we go to qfs_exit to clean up
and free all resources.
In that case we have not yet assigned rqst[2].rq_iov and thus
the rq_iov dereference in SMB2_close_free() will cause a NULL pointer
dereference.
Fixes: 1eb9fb5204 ("cifs: create SMB2_open_init()/SMB2_open_free() helpers")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Pull networking updates from David Miller:
1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson.
2) Add zero-copy AF_XDP support to i40e, from Björn Töpel.
3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we
can get rid of the {g,s}et_settings ethtool callbacks, from Michal
Kubecek.
4) Add software timestamping to veth driver, from Michael Walle.
5) More work to make packet classifiers and actions lockless, from Vlad
Buslov.
6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov.
7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks.
8) Support batching of XDP buffers in vhost_net, from Jason Wang.
9) Add flow dissector BPF hook, from Petar Penkov.
10) i40e vf --> generic iavf conversion, from Jesse Brandeburg.
11) Add NLA_REJECT netlink attribute policy type, to signal when users
provide attributes in situations which don't make sense. From
Johannes Berg.
12) Switch TCP and fair-queue scheduler over to earliest departure time
model. From Eric Dumazet.
13) Improve guest receive performance by doing rx busy polling in tx
path of vhost networking driver, from Tonghao Zhang.
14) Add per-cgroup local storage to bpf
15) Add reference tracking to BPF, from Joe Stringer. The verifier can
now make sure that references taken to objects are properly released
by the program.
16) Support in-place encryption in TLS, from Vakul Garg.
17) Add new taprio packet scheduler, from Vinicius Costa Gomes.
18) Lots of selftests additions, too numerous to mention one by one here
but all of which are very much appreciated.
19) Support offloading of eBPF programs containing BPF to BPF calls in
nfp driver, frm Quentin Monnet.
20) Move dpaa2_ptp driver out of staging, from Yangbo Lu.
21) Lots of u32 classifier cleanups and simplifications, from Al Viro.
22) Add new strict versions of netlink message parsers, and enable them
for some situations. From David Ahern.
23) Evict neighbour entries on carrier down, also from David Ahern.
24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann
and John Fastabend.
25) Add support for filtering route dumps, from David Ahern.
26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al.
27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido
Schimmel.
28) Add queue and stack map types to eBPF, from Mauricio Vasquez B.
29) Add back byte-queue-limit support to r8169, with all the bug fixes
in other areas of the driver it works now! From Florian Westphal and
Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits)
tcp: add tcp_reset_xmit_timer() helper
qed: Fix static checker warning
Revert "be2net: remove desc field from be_eq_obj"
Revert "net: simplify sock_poll_wait"
net: socionext: Reset tx queue in ndo_stop
net: socionext: Add dummy PHY register read in phy_write()
net: socionext: Stop PHY before resetting netsec
net: stmmac: Set OWN bit for jumbo frames
arm64: dts: stratix10: Support Ethernet Jumbo frame
tls: Add maintainers
net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes
octeontx2-af: Support for setting MAC address
octeontx2-af: Support for changing RSS algorithm
octeontx2-af: NIX Rx flowkey configuration for RSS
octeontx2-af: Install ucast and bcast pkt forwarding rules
octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response
octeontx2-af: NPC MCAM and LDATA extract minimal configuration
octeontx2-af: Enable packet length and csum validation
octeontx2-af: Support for VTAG strip and capture
...
Make the output of /proc/fs/cifs/DebugData a little easier to
read by cleaning up the listing of network interfaces removing
a wasted line break.
Here is a comparison of the network interface information
that from be viewed at the end of output from
"cat /proc/fs/cifs/DebugData"
Before:
Server interfaces: 8
0)
Speed: 10000000000 bps
Capabilities: rss
IPv6: fe80:0000:0000:0000:2cf5:407e:84b0:21dd
1)
Speed: 1000000000 bps
Capabilities:
IPv6: fe80:0000:0000:0000:61cd:6147:3d0c:f484
vs. after:
Server interfaces: 11
0) Speed: 10000000000 bps
Capabilities: rss
IPv6: fe80:0000:0000:0000:2cf5:407e:84b0:21dd
1) Speed: 2000000000 bps
Capabilities:
IPv6: fe80:0000:0000:0000:3d76:2d05:dcf8:ed10
Signed-off-by: Steve French <stfrench@microsoft.com>
To allow better debugging (for example applications with
handle leaks, or complex reconnect scenarios) display the
number of open files (on the client) and number of open
server file handles for each tcon in /proc/fs/cifs/Stats.
Note that open files on server is one larger than local
due to handle caching (in this case of the root of
the share). In this example there are two local
open files, and three (two file and one directory handle)
open on the server.
Sample output:
$ cat /proc/fs/cifs/Stats
Resources in use
CIFS Session: 1
Share (unique mount targets): 2
SMB Request/Response Buffer: 1 Pool size: 5
SMB Small Req/Resp Buffer: 1 Pool size: 30
Operations (MIDs): 0
0 session 0 share reconnects
Total vfs operations: 36 maximum at one time: 2
1) \\localhost\test
SMBs: 69
Bytes read: 27 Bytes written: 0
Open files: 2 total (local), 3 open on server
TreeConnects: 1 total 0 failed
TreeDisconnects: 0 total 0 failed
Creates: 19 total 0 failed
Closes: 16 total 0 failed
...
Signed-off-by: Steve French <stfrench@microsoft.com>
We do not call cifs_open_file() for directories and thus we do not have a
pSMBFile we can extract the FIDs from.
Solve this by instead always using a compounded open/query/close for
the passthrough ioctl.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In cases where queryinfo fails, we have cases in cifs (vers=1.0)
where with backupuid mounts we retry the query info with findfirst.
This doesn't work to some NetApp servers which don't support
WindowsXP (and later) infolevel 261 (SMB_FIND_FILE_ID_FULL_DIR_INFO)
so in this case use other info levels (in this case it will usually
be level 257, SMB_FIND_FILE_DIRECTORY_INFO).
(Also fixes some indentation)
See kernel bugzilla 201435
Signed-off-by: Steve French <stfrench@microsoft.com>
If backupuid mount option is sent, we can incorrectly retry
(on access denied on query info) with a cifs (FindFirst) operation
on an smb3 mount which causes the server to force the session close.
We set backup intent on open so no need for this fallback.
See kernel bugzilla 201435
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
When mounting with backupuid set, we should be setting
CREATE_OPEN_BACKUP_INTENT flag on compounded opens as well,
especially the case of compounded smb2_query_path_info.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
writepages and readpages operations did not call get/free_xid
so the statistics for file copy could get confusing with "vfs operations"
not increasing. Add get_xid and free_xid to cifs readpages and
writepages functions.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
There is a potential execution path in which variable *resp_buftype*
is passed as an argument to function free_rsp_buf(), in which it is
used in a comparison without being properly initialized previously.
Fix this by initializing variable *resp_buftype* to CIFS_NO_BUFFER
in order to avoid unpredictable or unintended results.
Addresses-Coverity-ID: 1473971 ("Uninitialized scalar variable")
Fixes: c5d25bdb2967 ("cifs: add IOCTL for QUERY_INFO passthrough to userspace")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
This allows userspace tools to query the raw info levels for cifs files
and process the response in userspace.
In particular this is useful for many of those data where there is no
corresponding native data structure in linux.
For example querying the security descriptor for a file and extract the
SIDs.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Clarify meaning (in comments) meaning of various
options for debug messages in cifs.ko. Also fixed
trivial formatting/style issue with previous patch.
Signed-off-by: Steve French <stfrench@microsoft.com>
Currently, no messages are printed when mounting a CIFS filesystem and
no debug configuration is enabled.
However, a CIFS mount information is valuable when troubleshooting
and/or forensic analyzing a system and finding out if was a CIFS
endpoint mount attempted.
Other filesystems such as XFS, EXT* does issue a printk() when mounting
their filesystems.
A terse log message is printed only if cifsFYI is not enabled. Otherwise,
the default full debug message is printed.
In order to not clutter and classify correctly the event messages, these
are logged as KERN_INFO level.
Sample mount operations:
[root@corinthians ~]# mount -o user=administrator //172.25.250.18/c$ /mnt
(non-existent system)
[root@corinthians ~]# mount -o user=administrator //172.25.250.19/c$ /mnt
(Valid system)
Kernel message log for the mount operations:
[ 450.464543] CIFS: Attempting to mount //172.25.250.18/c$
[ 456.478186] CIFS VFS: Error connecting to socket. Aborting operation.
[ 456.478381] CIFS VFS: cifs_mount failed w/return code = -113
[ 467.688866] CIFS: Attempting to mount //172.25.250.19/c$
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Currently, CIFS lacks a internal logging function that prints out data
when CIFS_DEBUG=n. When CIFS_DEBUG=y, the only message level for CIFS
events are KERN_ERR or KERN_DEBUG.
This patch creates cifs_info(), which is useful for printing
non-critical event messges, at either CIFS_DEBUG state.
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
RHBZ 1484130
Update cifs_find_fid_lock_conflict() to recognize that
ODF locks do not conflict with eachother.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
It is not necessary to deregister a memory registration after it has been
successfully invalidated.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
When issuing SMB1 read/write, pass the page offset to transport.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In some error conditions, resp_buftype can be passed uninitialised to
free_rsp_buf(), potentially resulting in a spurious debug message.
If resp_buftype randomly had the value 1 (CIFS_SMALL_BUFFER) then this
would log a debug message.
The rsp pointer is initialised to NULL so there is no other side-effect.
Detected by CoverityScan, CID 1438585 ("Uninitialized scalar variable")
Detected by CoverityScan, CID 1438667 ("Uninitialized scalar variable")
Detected by CoverityScan, CID 1438764 ("Uninitialized scalar variable")
Signed-off-by: Garry McNulty <garrmcnu@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Be able to log a ftrace message on success and/or failure of
sending a lease break response to the server.
Example output:
TASK-PID CPU# |||| TIMESTAMP FUNCTION
| | | |||| | |
kworker/1:1-5681 [001] .... 11123.530457: smb3_lease_done: sid=0x291e3e0f tid=0x8ba43071 lease_key=0x1852ca0d3ecd9b55847750a86716fde lease_state=0x0
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
In network file system it is fairly easy for server and client
atime vs. mtime to get confused (and atime updated less frequently)
which we noticed broke some apps which expect atime >= mtime
Also ignore relatime mount option (rather than error on it) since
relatime is basically what some network server fs are doing
(relatime).
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Modern servers often support 8MB as maximum i/o size, and we see some
performance benefits (my testing showed 1 to 13% on write paths,
and 1 to 3% on read paths for increasing the default to 4MB). If server
doesn't support larger i/o size, during negotiate protocol it is already
set correctly to the server's maximum if lower than 4MB.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
As we reset credits later in the reconnect path, useful
to have optional (cifsFYI) debug message.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
tcon->Flags is only used by SMB1 code and changing it is not permanent
(you lose the setting on tcon reconnect).
* Move the setting to superblock flags (per mount-points).
* Make automount callback exit early when flag present
* Make dfs resolving happening in mount syscall exit early if flag present
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Each time we reconnect to the same server, bump an instance
counter (and display in /proc/fs/cifs/DebugData) to make it
easier to debug.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Previously reserved dpen response field changed in smb3
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
/proc/fs/cifs/Stats when CONFIG_CIFS_STATS2 is enabled logs 'slow'
responses, but depending on the server you are debugging a
one second timeout may be too fast, so allow setting it to
a larger number of seconds via new module parameter
/sys/module/cifs/parameters/slow_rsp_threshold
or via modprobe:
slow_rsp_threshold:Amount of time (in seconds) to wait before
logging that a response is delayed.
Default: 1 (if set to 0 disables msg). (uint)
Recommended values are 0 (disabled) to 32767 (9 hours) with
the default remaining as 1 second.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
note smb3 (and common more modern servers) in the module description
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
For a network file system we generally prefer large i/o, but
if the server returns invalid file system block/sector sizes
in cifs (vers=1.0) QFSInfo then set block size to a default
of a reasonable minimum (4K).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Currently, "echo 0 > /proc/fs/cifs/Stats" resets all of the stats
except the session and share reconnect counts. Fix it to
reset those as well.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
When "backup intent" is requested on the mount (e.g. backupuid or
backupgid mount options), the corresponding flag was missing from
some of the new compounding operations as well (now that
open_query_close is gone).
Related to kernel bugzilla #200953
Reported-and-tested-by: <whh@rubrik.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
So we don't overflow the io vector arrays accidentally
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Get rid of smb2_open_op_close() as all operations are now migrated
to smb2_compound_op().
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
We never pass is_falloc==true here anyway and if we ever need to support
is_falloc in the future, SMB2_set_eof is such a trivial wrapper around
send_set_info() that we can/should just create a differently named wrapper
for that new functionality.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Cuts number of network roundtrips significantly for some common syscalls
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This changes SMB2_OP_SET_EOF to use compounding in some situations.
This is part of the path based API to truncate a file.
Most of the time this will however not be invoked for SMB2 since
cifs_set_file_size() will as far as I can tell almost always just
open the file synchronously and switch to the handle based truncate
code path, thus bypassing the compounding we add here.
Rewriting cifs_set_file_size() and make that whole pile of code more
compounding friendly, and also easier to read and understand, is a
different project though and not for this patch.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This and previous patches drop the number of roundtrips we need for rmdir()
from 6 to 2.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
so that we can use these later for compounded set-info calls.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This,and previous patches, drops the number of roundtrips from five to two
for unlink()
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This with the previous patch changes mkdir() from needing 6 roundtrips to
just 3.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This turns most open/query-info/close patterns in cifs.ko
to become compounds.
This changes stat from using 3 roundtrips to just a single one.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
When processing the mids for compounds we would only add credits based on
the last successful mid in the compound which would leak credits and
eventually triggering a re-connect.
Fix this by splitting the mid processing part into two loops instead of one
where the first loop just waits for all mids and then counts how many
credits we were granted for the whole compound.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Add tracepoint to catch potential cases where a pending operation overlapping a
reconnect could fail and incorrectly refund its credits causing the client
to think it has more credits available than the server thinks it does.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
fs/cifs/ioctl.c: In function 'cifs_ioctl':
fs/cifs/ioctl.c:164:23: warning:
variable 'cifs_sb' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Use kmemdup rather than duplicating its implementation
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Some servers (e.g. Azure) return "STATUS_NOT_IMPLEMENTED" rather
than "STATUS_INVALID_DEVICE_REQUEST" on query network interface
info at mount. This shouldn't cause us to log a warning message
automatically. Don't log this unless noisier cifsFYI is enabled.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Send probes to all the unprobed fileservers in a fileserver list on all
addresses simultaneously in an attempt to find out the fastest route whilst
not getting stuck for 20s on any server or address that we don't get a
reply from.
This alleviates the problem whereby attempting to access a new server can
take a long time because the rotation algorithm ends up rotating through
all servers and addresses until it finds one that responds.
Signed-off-by: David Howells <dhowells@redhat.com>
In some circumstances, the callback interest pointer is NULL, so in such a
case we can't dereference it when checking to see if the callback is
broken. This causes an oops in some circumstances.
Fix this by replacing the function that worked out the aggregate break
counter with one that actually does the comparison, and then make that
return true (ie. broken) if there is no callback interest as yet (ie. the
pointer is NULL).
Fixes: 68251f0a68 ("afs: Fix whole-volume callback handling")
Signed-off-by: David Howells <dhowells@redhat.com>
Eliminate the address pointer from the address list cursor as it's
redundant (ac->addrs[ac->index] can be used to find the same address) and
address lists must be replaced rather than being rearranged, so is of
limited value.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide an option to allow the file or volume location server cursor to be
dumped if the rotation routine falls off the end without managing to
contact a server.
Signed-off-by: David Howells <dhowells@redhat.com>
Implement support for talking to YFS-variant fileservers in the cache
manager and the filesystem client. These implement upgraded services on
the same port as their AFS services.
YFS fileservers provide expanded capabilities over AFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Expand fields in various data structures to support the expanded
information that YFS is capable of returning.
Signed-off-by: David Howells <dhowells@redhat.com>
Get the target vnode in afs_rmdir() and validate it before we attempt the
deletion, The vnode pointer will be passed through to the delivery function
in a later patch so that the delivery function can mark it deleted.
Signed-off-by: David Howells <dhowells@redhat.com>
Calculate the callback expiration time at the point of operation reply
delivery, using the reply time queried from AF_RXRPC on that call as a
base.
Signed-off-by: David Howells <dhowells@redhat.com>
The FS.FetchStatus reply delivery function was updating inode of the
directory in which a lookup had been done with the status of the looked up
file. This corrupts some of the directory state.
Fixes: 5cf9dd55a0 ("afs: Prospectively look up extra files when doing a single lookup")
Signed-off-by: David Howells <dhowells@redhat.com>
Implement the YFS cache manager service which gives extra capabilities on
top of AFS. This is done by listening for an additional service on the
same port and indicating that anyone requesting an upgrade should be
upgraded to the YFS port.
Signed-off-by: David Howells <dhowells@redhat.com>
Remove unnecessary details of a broken callback, such as version, expiry
and type, from the afs_callback_break struct as they're not actually used
and make the list take more memory.
Signed-off-by: David Howells <dhowells@redhat.com>
Call the function to commit the status on a new file, dir or symlink so
that the access rights for the caller's key are cached for that object.
Without this, the next access to the file will cause a FetchStatus
operation to be emitted to retrieve the access rights.
Signed-off-by: David Howells <dhowells@redhat.com>
Increase the sizes of the volume ID to 64 bits and the vnode ID (inode
number equivalent) to 96 bits to allow the support of YFS.
This requires the iget comparator to check the vnode->fid rather than i_ino
and i_generation as i_ino is not sufficiently capacious. It also requires
this data to be placed into the vnode cache key for fscache.
For the moment, just discard the top 32 bits of the vnode ID when returning
it though stat.
Signed-off-by: David Howells <dhowells@redhat.com>
When writing a new page, clear space in the page rather than attempting to
load it from the server if the space is beyond the EOF.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix afs_deliver_to_call() to handle -EIO being returned by the operation
delivery function, indicating that the call found itself in the wrong
state, by printing an error and aborting the call.
Currently, an assertion failure will occur. This can happen, say, if the
delivery function falls off the end without calling afs_extract_data() with
the want_more parameter set to false to collect the end of the Rx phase of
a call.
The assertion failure looks like:
AFS: Assertion failed
4 == 7 is false
0x4 == 0x7 is false
------------[ cut here ]------------
kernel BUG at fs/afs/rxrpc.c:462!
and is matched in the trace buffer by a line like:
kworker/7:3-3226 [007] ...1 85158.030203: afs_io_error: c=0003be0c r=-5 CM_REPLY
Fixes: 98bf40cd99 ("afs: Protect call->state changes against signals")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Currently the TTL on VL server and address lists isn't set in all
circumstances and may be set to poor choices in others, since the TTL is
derived from the SRV/AFSDB DNS record if and when available.
Fix the TTL by limiting the range to a minimum and maximum from the current
time. At some point these can be made into sysctl knobs. Further, use the
TTL we obtained from the upcall to set the expiry on negative results too;
in future a mechanism can be added to force reloading of such data.
Signed-off-by: David Howells <dhowells@redhat.com>
Track VL servers as independent entities rather than lumping all their
addresses together into one set and implement server-level rotation by:
(1) Add the concept of a VL server list, where each server has its own
separate address list. This code is similar to the FS server list.
(2) Use the DNS resolver to retrieve a set of servers and their associated
addresses, ports, preference and weight ratings.
(3) In the case of a legacy DNS resolver or an address list given directly
through /proc/net/afs/cells, create a list containing just a dummy
server record and attach all the addresses to that.
(4) Implement a simple rotation policy, for the moment ignoring the
priorities and weights assigned to the servers.
(5) Show the address list through /proc/net/afs/<cell>/vlservers. This
also displays the source and status of the data as indicated by the
upcall.
Signed-off-by: David Howells <dhowells@redhat.com>
Improve the error handling in FS server rotation by:
(1) Cache the latest useful error value for the fs operation as a whole in
struct afs_fs_cursor separately from the error cached in the
afs_addr_cursor struct. The one in the address cursor gets clobbered
occasionally. Copy over the error to the fs operation only when it's
something we'd be interested in passing to userspace.
(2) Make it so that EDESTADDRREQ is the default that is seen only if no
addresses are available to be accessed.
(3) When calling utility functions, such as checking a volume status or
probing a fileserver, don't let a successful result clobber the cached
error in the cursor; instead, stash the result in a temporary variable
until it has been assessed.
(4) Don't return ETIMEDOUT or ETIME if a better error, such as
ENETUNREACH, is already cached.
(5) On leaving the rotation loop, turn any remote abort code into a more
useful error than ECONNABORTED.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
afs_extract_data sets up a temporary iov_iter and passes it to AF_RXRPC
each time it is called to describe the remaining buffer to be filled.
Instead:
(1) Put an iterator in the afs_call struct.
(2) Set the iterator for each marshalling stage to load data into the
appropriate places. A number of convenience functions are provided to
this end (eg. afs_extract_to_buf()).
This iterator is then passed to afs_extract_data().
(3) Use the new ITER_DISCARD iterator to discard any excess data provided
by FetchData.
Signed-off-by: David Howells <dhowells@redhat.com>
Include the site of detection of AFS protocol errors in trace lines to
better be able to determine what went wrong.
Signed-off-by: David Howells <dhowells@redhat.com>
In the iov_iter struct, separate the iterator type from the iterator
direction and use accessor functions to access them in most places.
Convert a bunch of places to use switch-statements to access them rather
then chains of bitwise-AND statements. This makes it easier to add further
iterator types. Also, this can be more efficient as to implement a switch
of small contiguous integers, the compiler can use ~50% fewer compare
instructions than it has to use bitwise-and instructions.
Further, cease passing the iterator type into the iterator setup function.
The iterator function can set that itself. Only the direction is required.
Signed-off-by: David Howells <dhowells@redhat.com>
Use accessor functions to access an iterator's type and direction. This
allows for the possibility of using some other method of determining the
type of iterator than if-chains with bitwise-AND conditions.
Signed-off-by: David Howells <dhowells@redhat.com>
The filehandle has a length which is defined as a 32-bit
"unsigned integer". Change sign of the length appropriately.
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Pull x86 mm updates from Ingo Molnar:
"Lots of changes in this cycle:
- Lots of CPA (change page attribute) optimizations and related
cleanups (Thomas Gleixner, Peter Zijstra)
- Make lazy TLB mode even lazier (Rik van Riel)
- Fault handler cleanups and improvements (Dave Hansen)
- kdump, vmcore: Enable kdumping encrypted memory with AMD SME
enabled (Lianbo Jiang)
- Clean up VM layout documentation (Baoquan He, Ingo Molnar)
- ... plus misc other fixes and enhancements"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
x86/stackprotector: Remove the call to boot_init_stack_canary() from cpu_startup_entry()
x86/mm: Kill stray kernel fault handling comment
x86/mm: Do not warn about PCI BIOS W+X mappings
resource: Clean it up a bit
resource: Fix find_next_iomem_res() iteration issue
resource: Include resource end in walk_*() interfaces
x86/kexec: Correct KEXEC_BACKUP_SRC_END off-by-one error
x86/mm: Remove spurious fault pkey check
x86/mm/vsyscall: Consider vsyscall page part of user address space
x86/mm: Add vsyscall address helper
x86/mm: Fix exception table comments
x86/mm: Add clarifying comments for user addr space
x86/mm: Break out user address space handling
x86/mm: Break out kernel address space handling
x86/mm: Clarify hardware vs. software "error_code"
x86/mm/tlb: Make lazy TLB mode lazier
x86/mm/tlb: Add freed_tables element to flush_tlb_info
x86/mm/tlb: Add freed_tables argument to flush_tlb_mm_range
smp,cpumask: introduce on_each_cpu_cond_mask
smp: use __cpumask_set_cpu in on_each_cpu_cond
...
Pull locking and misc x86 updates from Ingo Molnar:
"Lots of changes in this cycle - in part because locking/core attracted
a number of related x86 low level work which was easier to handle in a
single tree:
- Linux Kernel Memory Consistency Model updates (Alan Stern, Paul E.
McKenney, Andrea Parri)
- lockdep scalability improvements and micro-optimizations (Waiman
Long)
- rwsem improvements (Waiman Long)
- spinlock micro-optimization (Matthew Wilcox)
- qspinlocks: Provide a liveness guarantee (more fairness) on x86.
(Peter Zijlstra)
- Add support for relative references in jump tables on arm64, x86
and s390 to optimize jump labels (Ard Biesheuvel, Heiko Carstens)
- Be a lot less permissive on weird (kernel address) uaccess faults
on x86: BUG() when uaccess helpers fault on kernel addresses (Jann
Horn)
- macrofy x86 asm statements to un-confuse the GCC inliner. (Nadav
Amit)
- ... and a handful of other smaller changes as well"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
locking/lockdep: Make global debug_locks* variables read-mostly
locking/lockdep: Fix debug_locks off performance problem
locking/pvqspinlock: Extend node size when pvqspinlock is configured
locking/qspinlock_stat: Count instances of nested lock slowpaths
locking/qspinlock, x86: Provide liveness guarantee
x86/asm: 'Simplify' GEN_*_RMWcc() macros
locking/qspinlock: Rework some comments
locking/qspinlock: Re-order code
locking/lockdep: Remove duplicated 'lock_class_ops' percpu array
x86/defconfig: Enable CONFIG_USB_XHCI_HCD=y
futex: Replace spin_is_locked() with lockdep
locking/lockdep: Make class->ops a percpu counter and move it under CONFIG_DEBUG_LOCKDEP=y
x86/jump-labels: Macrofy inline assembly code to work around GCC inlining bugs
x86/cpufeature: Macrofy inline assembly code to work around GCC inlining bugs
x86/extable: Macrofy inline assembly code to work around GCC inlining bugs
x86/paravirt: Work around GCC inlining bugs when compiling paravirt ops
x86/bug: Macrofy the BUG table section handling, to work around GCC inlining bugs
x86/alternatives: Macrofy lock prefixes to work around GCC inlining bugs
x86/refcount: Work around GCC inlining bug
x86/objtool: Use asm macros to work around GCC inlining bugs
...
With the preparations all being done this patch now enables authentication
support for UBIFS. Authentication is enabled when the newly introduced
auth_key and auth_hash_name mount options are passed. auth_key provides
the key which is used for authentication whereas auth_hash_name provides
the hashing algorithm used for this FS. Passing these options make
authentication mandatory and only UBIFS images that can be authenticated
with the given key are allowed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
In authenticated mode we cannot fixup the inode sizes in-place
during recovery as this would invalidate the hashes and HMACs
we stored for this inode.
Instead, we just write the updated inodes to the journal. We can
only do this after ubifs_rcvry_gc_commit() is done though, so for
authenticated mode call ubifs_recover_size() after
ubifs_rcvry_gc_commit() and not vice versa as normally done.
Calling ubifs_recover_size() after ubifs_rcvry_gc_commit() has the
drawback that after a commit the size fixup information is gone, so
when a powercut happens while recovering from another powercut
we may lose some data written right before the first powercut.
This is why we only do this in authenticated mode and leave the
behaviour for unauthenticated mode untouched.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch calculates the necessary hashes and HMACs for the default
filesystem so that the dynamically created default fs can be
authenticated.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
This adds a HMAC covering the super block node and adds the logic that
decides if a filesystem shall be mounted unauthenticated or
authenticated.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
During creation of the default filesystem on an empty flash the default
LPT is created. With this patch a hash over the default LPT is
calculated which can be added to the default filesystems master node.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The master node contains hashes over the root index node and the LPT.
This patch adds a HMAC to authenticate the master node itself.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The LPT needs to be authenticated aswell. Since the LPT is only written
during commit it is enough to authenticate the whole LPT with a single
hash which is stored in the master node. Only the leaf nodes (pnodes)
are hashed which makes the implementation much simpler than it would be
to hash the complete LPT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Make sure that during replay all buds can be authenticated. To do
this we calculate the hash chain until we find an authentication
node and check the HMAC in that node against the current status
of the hash chain.
After a power cut it can happen that some nodes have been written, but
not yet the authentication node for them. These nodes have to be
discarded during replay.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
To be able to authenticate the garbage collector journal head add
authentication nodes to the buds the garbage collector creates.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Nodes that are written to flash can only be authenticated through the
index after the next commit. When a journal replay is necessary the
nodes are not yet referenced by the index and thus can't be
authenticated.
This patch overcomes this situation by creating a hash over all nodes
beginning from the commit start node over the reference node(s) and
the buds themselves. From
time to time we insert authentication nodes. Authentication nodes
contain a HMAC from the current hash state, so that they can be
used to authenticate a journal replay up to the point where the
authentication node is. The hash is continued afterwards
so that theoretically we would only have to check the HMAC of
the last authentication node we find.
Overall we get this picture:
,,,,,,,,
,......,...........................................
,. CS , hash1.----. hash2.----.
,. | , . |hmac . |hmac
,. v , . v . v
,.REF#0,-> bud -> bud -> bud.-> auth -> bud -> bud.-> auth ...
,..|...,...........................................
, | ,
, | ,,,,,,,,,,,,,,,
. | hash3,----.
, | , |hmac
, v , v
, REF#1 -> bud -> bud,-> auth ...
,,,|,,,,,,,,,,,,,,,,,,
v
REF#2 -> ...
|
V
...
Note how hash3 covers CS, REF#0 and REF#1 so that it is not possible to
exchange or skip any reference nodes. Unlike the picture suggests the
auth nodes themselves are not hashed.
With this it is possible for an offline attacker to cut each journal
head or to drop the last reference node(s), but not to skip any journal
heads or to reorder any operations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
With this patch the hashes over the index nodes stored in the tree node
cache are written to flash and are checked when read back from flash.
The hash of the root index node is stored in the master node.
During journal replay the hashes are regenerated from the read nodes
and stored in the tree node cache. This means the nodes must previously
be authenticated by other means. This is done in a later patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
As part of the UBIFS authentication support every branch in the index
gets a hash covering the referenced node. To make that happen the tree
node cache needs hashes over the nodes. This patch adds a hash argument
to ubifs_tnc_add() and ubifs_tnc_add_nm(). The hashes are calculated
from the callers of these functions which actually prepare the nodes.
With this patch all the leaf nodes of the index tree get hashes, but
currently nothing is done with these hashes, this is left for a later
patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
With authentication support some nodes (master node, super block node)
get a HMAC embedded into them. This patch adds functions to prepare and
write such a node.
The difficulty is that besides the HMAC the nodes also have a CRC which
must stay valid. This means we first have to initialize all fields in
the node, then calculate the HMAC (not covering the CRC) and finally
calculate the CRC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch adds the various helper functions needed for authentication
support. We need functions to hash nodes, to embed HMACs into a node and
to compare hashes and HMACs. Most functions first check if this
filesystem is authenticated and bail out early if not, which makes the
functions safe to be called with disabled authentication.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
When adding authentication support we will embed a HMAC into some
nodes. To prepare these nodes we have to first initialize the nodes,
then add a HMAC and finally add a CRC. To accomplish this add separate
ubifs_init_node/ubifs_crc_node functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch adds the changes to the on disk format needed for
authentication support. We'll add:
* a HMAC covering super block node
* a HMAC covering the master node
* a hash over the root index node to the master node
* a hash over the LPT to the master node
* a flag to the filesystem flag indicating the filesystem is
authenticated
* an authentication node necessary to authenticate the nodes written
to the journal heads while they are written.
* a HMAC of a well known message to the super block node to be able
to check if the correct key is provided
And finally, not visible in this patch, nevertheless explained here:
* hashes over the referenced child nodes in each branch of a index node
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The superblock node is read/modified/written several times throughout
the UBIFS code. Instead of reading it from the device each time just
keep a copy in memory and write back the modified copy when necessary.
This patch helps for authentication support, here we not only have to
read the superblock node, but also have to authenticate it, which
is easier if we do it once during initialization.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
write_node() is used only once and can easily be replaced with calls
to ubifs_prepare_node()/write_head() which makes the code a bit shorter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
ubifs_lpt_lookup() starts by looking up the nth pnode in the LPT. We
already have this functionality in ubifs_pnode_lookup(). Use this
function rather than open coding its functionality.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
ubifs_lpt_lookup could be implemented using pnode_lookup. To make that
possible move pnode_lookup from lpt.c to lpt_commit.c. Rename it to
ubifs_pnode_lookup since it's now exported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
read_znode() takes len, lnum and offs arguments which the caller all
extracts from the same struct ubifs_zbranch *. When adding authentication
support we would have to add a pointer to a hash to the arguments which
is also part of struct ubifs_zbranch. Pass the ubifs_zbranch * instead
so that we do not have to add another argument.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
try_read_node() takes len, lnum and offs arguments which the caller all
extracts from the same struct ubifs_zbranch *. When adding authentication
support we would have to add a pointer to a hash to the arguments which
is also part of struct ubifs_zbranch. Pass the ubifs_zbranch * instead
so that we do not have to add another argument.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
create_default_filesystem() allocates memory for a node, writes that
node and frees the memory directly afterwards. With this patch we
allocate memory for all nodes at the beginning of the function and
free the memory at the end. This makes it easier to implement
authentication support since with authentication support we'll need
the contents of some nodes when creating other nodes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch does below changes to keep consistence of project quota data
in sudden power-cut case:
- update inode.i_projid and project quota atomically under lock_op() in
f2fs_ioc_setproject()
- recover inode.i_projid and project quota in recover_inode()
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For journalled quota mode, let checkpoint to flush dquot dirty data
and quota file data to guarntee persistence of all quota sysfile in
last checkpoint, by this way, we can avoid corrupting quota sysfile
when encountering SPO.
The implementation is as below:
1. add a global state SBI_QUOTA_NEED_FLUSH to indicate that there is
cached dquot metadata changes in quota subsystem, and later checkpoint
should:
a) flush dquot metadata into quota file.
b) flush quota file to storage to keep file usage be consistent.
2. add a global state SBI_QUOTA_NEED_REPAIR to indicate that quota
operation failed due to -EIO or -ENOSPC, so later,
a) checkpoint will skip syncing dquot metadata.
b) CP_QUOTA_NEED_FSCK_FLAG will be set in last cp pack to give a
hint for fsck repairing.
3. add a global state SBI_QUOTA_SKIP_FLUSH, in checkpoint, if quota
data updating is very heavy, it may cause hungtask in block_operation().
To avoid this, if our retry time exceed threshold, let's just skip
flushing and retry in next checkpoint().
Signed-off-by: Weichao Guo <guoweichao@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: avoid warnings and set fsck flag]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Direct IO can be used in case of hardware encryption. The following
scenario results into data corruption issue in this path -
Thread A - Thread B-
-> write file#1 in direct IO
-> GC gets kicked in
-> GC submitted bio on meta mapping
for file#1, but pending completion
-> write file#1 again with new data
in direct IO
-> GC bio gets completed now
-> GC writes old data to the new
location and thus file#1 is
corrupted.
Fix this by submitting and waiting for pending io on meta mapping
for direct IO case in f2fs_map_blocks().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Testcase to reproduce this bug:
1. mkfs.f2fs /dev/sdd
2. mount -t f2fs /dev/sdd /mnt/f2fs
3. touch /mnt/f2fs/file
4. sync
5. chattr +a /mnt/f2fs/file
6. xfs_io -a /mnt/f2fs/file -c "fsync"
7. godown /mnt/f2fs
8. umount /mnt/f2fs
9. mount -t f2fs /dev/sdd /mnt/f2fs
10. xfs_io /mnt/f2fs/file
There is no error when opening this file w/o O_APPEND, but actually,
we expect the correct result should be:
/mnt/f2fs/file: Operation not permitted
The root cause is, in recover_inode(), we recover inode->i_flags more
than F2FS_I(inode)->i_flags, so fix it.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes codes as below:
- use f2fs_set_inode_flags() to update i_flags atomically to avoid
potential race.
- synchronize F2FS_I(inode)->i_flags to inode->i_flags in
f2fs_new_inode().
- use f2fs_set_inode_flags() to simply codes in f2fs_quota_{on,off}.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We need to drop PG_checked flag on page as well when we clear PG_uptodate
flag, in order to avoid treating the page as GCing one later.
Signed-off-by: Weichao Guo <guoweichao@huawei.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This reverts commit 66110abc4c.
If we clear the cold data flag out of the writeback flow, we can miscount
-1 by end_io, which incurs a deadlock caused by all I/Os being blocked during
heavy GC.
Balancing F2FS Async:
- IO (CP: 1, Data: -1, Flush: ( 0 0 1), Discard: ( ...
GC thread: IRQ
- move_data_page()
- set_page_dirty()
- clear_cold_data()
- f2fs_write_end_io()
- type = WB_DATA_TYPE(page);
here, we get wrong type
- dec_page_count(sbi, type);
- f2fs_wait_on_page_writeback()
Cc: <stable@vger.kernel.org>
Reported-and-Tested-by: Park Ju Hyung <qkrwngud825@gmail.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds issued read IO counts which is under block layer.
Chao modified a bit, since:
Below race can cause reversed reference on F2FS_RD_DATA, there is
the same issue in f2fs_submit_page_bio(), fix them by relocate
__submit_bio() and inc_page_count.
Thread A Thread B
- f2fs_write_begin
- f2fs_submit_page_read
- __submit_bio
- f2fs_read_end_io
- __read_end_io
- dec_page_count(, F2FS_RD_DATA)
- inc_page_count(, F2FS_RD_DATA)
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now, we have supported cgroup writeback, it depends on correctly IO
account of specified filesystem.
But in commit d1b3e72d54 ("f2fs: submit bio of in-place-update pages"),
we split write paths from f2fs_submit_page_mbio() to two:
- f2fs_submit_page_bio() for IPU path
- f2fs_submit_page_bio() for OPU path
But still we account write IO only in f2fs_submit_page_mbio(), result in
incorrect IO account, fix it by adding missing IO account in IPU path.
Fixes: d1b3e72d54 ("f2fs: submit bio of in-place-update pages")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Below race can cause reversed reference on dirty count, fix it by
relocating __submit_bio() and inc_page_count().
Thread A Thread B
- f2fs_inplace_write_data
- f2fs_submit_page_bio
- __submit_bio
- f2fs_write_end_io
- dec_page_count
- inc_page_count
Cc: <stable@vger.kernel.org>
Fixes: d1b3e72d54 ("f2fs: submit bio of in-place-update pages")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Core changes:
* Support non-uniform erase size
* Support controllers with limited TX fifo size
Driver changes:
* m25p80: Re-issue a WREN command after each write access
* cadence: Pass a proper dir value to dma_[un]map_single()
* fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
* intel-spi: Add a new PCI entry for Ice Lake
NAND changes:
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
MTD changes:
* physmap cleanups/fixe
* gpio-addr-flash cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=7w4w
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
When ramoops reserved a memory region in the kernel, it had an unhelpful
label of "persistent_memory". When reading /proc/iomem, it would be
repeated many times, did not hint that it was ramoops in particular,
and didn't clarify very much about what each was used for:
400000000-407ffffff : Persistent Memory (legacy)
400000000-400000fff : persistent_memory
400001000-400001fff : persistent_memory
...
4000ff000-4000fffff : persistent_memory
Instead, this adds meaningful labels for how the various regions are
being used:
400000000-407ffffff : Persistent Memory (legacy)
400000000-400000fff : ramoops:dump(0/252)
400001000-400001fff : ramoops:dump(1/252)
...
4000fc000-4000fcfff : ramoops:dump(252/252)
4000fd000-4000fdfff : ramoops:console
4000fe000-4000fe3ff : ramoops:ftrace(0/3)
4000fe400-4000fe7ff : ramoops:ftrace(1/3)
4000fe800-4000febff : ramoops:ftrace(2/3)
4000fec00-4000fefff : ramoops:ftrace(3/3)
4000ff000-4000fffff : ramoops:pmsg
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
This refactors compression initialization slightly to better handle
getting potentially called twice (via early pstore_register() calls
and later pstore_init()) and improves the comments and reporting to be
more verbose.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
ramoops's call of pstore_register() was recently moved to run during
late_initcall() because the crypto backend may not have been ready during
postcore_initcall(). This meant early-boot crash dumps were not getting
caught by pstore any more.
Instead, lets allow calls to pstore_register() earlier, and once crypto
is ready we can initialize the compression.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Fixes: cb3bee0369 ("pstore: Use crypto compress API")
[kees: trivial rebase]
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
In preparation for having additional actions during init/exit, this moves
the init/exit into platform.c, centralizing the logic to make call outs
to the fs init/exit.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Add a new mount option 'nocopyfrom' that will prevent the usage of the
RADOS 'copy-from' operation in cephfs. This could be useful, for example,
for an administrator to temporarily mitigate any possible bugs in the
'copy-from' implementation.
Currently, only copy_file_range uses this RADOS operation. Setting this
mount option will result in this syscall reverting to the default VFS
implementation, i.e. to perform the copies locally instead of doing remote
object copies.
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This commit implements support for the copy_file_range syscall in cephfs.
It is implemented using the RADOS 'copy-from' operation, which allows to
do a remote object copy, without the need to download/upload data from/to
the OSDs.
Some manual copy may however be required if the source/destination file
offsets aren't object aligned or if the copy length is smaller than the
object size.
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
ceph_try_get_caps currently calls try_get_cap_refs with the nonblock
parameter always set to 'true'. This change adds a new parameter that
allows to set it's value. This will be useful for a follow-up patch that
will need to get two sets of capabilities for two different inodes without
risking a deadlock.
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Currently message data items are allocated with ceph_msg_data_create()
in setup_request_data() inside send_request(). send_request() has never
been allowed to fail, so each allocation is followed by a BUG_ON:
data = ceph_msg_data_create(...);
BUG_ON(!data);
It's been this way since support for multiple message data items was
added in commit 6644ed7b7e ("libceph: make message data be a pointer")
in 3.10.
There is no reason to delay the allocation of message data items until
the last possible moment and we certainly don't need a linked list of
them as they are only ever appended to the end and never erased. Make
ceph_msg_new2() take max_data_items and adapt the rest of the code.
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The current requirement is that ceph_osdc_alloc_messages() should be
called after oid and oloc are known. In preparation for preallocating
message data items, move ceph_osdc_alloc_messages() further down, so
that it is called when OSD op codes are known.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
__cap_delay_requeue could be invoked through ceph_check_caps when there
exists caps that needs to be sent and are delayed by "i_hold_caps_min"
or "i_hold_caps_max". If __cap_delay_requeue sets timeout unconditionally,
there could be a chance that some "wanted" caps can not be release for a
long since their timeouts are reset every time they get delayed.
Fixes: http://tracker.ceph.com/issues/36369
Signed-off-by: Xuehan Xu <xuxuehan@360.cn>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Because send_mds_reconnect() wants to send a message with a pagelist
and pass the ownership to the messenger, ceph_msg_data_add_pagelist()
consumes a ref which is then put in ceph_msg_data_destroy(). This
makes managing pagelists in the OSD client (where they are wrapped in
ceph_osd_data) unnecessarily hard because the handoff only happens in
ceph_osdc_start_request() instead of when the pagelist is passed to
ceph_osd_data_pagelist_init(). I counted several memory leaks on
various error paths.
Fix up ceph_msg_data_add_pagelist() and carry a pagelist ref in
ceph_osd_data.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
struct ceph_pagelist cannot be embedded into anything else because it
has its own refcount. Merge allocation and initialization together.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Current implementation of cephfs fallocate isn't correct as it doesn't
really reserve the space in the cluster, which means that a subsequent
call to a write may actually fail due to lack of space. In fact, it is
currently possible to fallocate an amount space that is larger than the
free space in the cluster. It has behaved this way since the initial
commit ad7a60de88 ("ceph: punch hole support").
Since there's no easy solution to fix this at the moment, this patch
simply removes support for all fallocate operations but
FALLOC_FL_PUNCH_HOLE (which implies FALLOC_FL_KEEP_SIZE).
Link: https://tracker.ceph.com/issues/36317
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Avoid allocating memory for the entire user request: striped_read()
does a synchronous OSD request per object, so it doesn't need more than
object size worth of pages at a time.
[ Preserve the comment, changelog. ]
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This reverts commit 8b8f53af1e.
splice_dentry() is used by three places. For two places, req->r_dentry
is passed to splice_dentry(). In the case of error, req->r_dentry does
not get updated. So splice_dentry() should not drop reference.
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Do the snap check first in ceph_set_acl(), so we can avoid
unnecessary operations when the inode has snap.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
__cap_delay_requeue() only requeue inode which does not
have CEPH_I_FLUSH flag, so avoid reset cap hold timeout
for that inode.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
With no more radix tree API users left, we can drop the GFP flags
and use xa_init() instead of INIT_RADIX_TREE().
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Instead of using a pagevec, just use the XArray iterators. Add a
conditional rescheduling point which probably should have been there in
the original.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Add some XArray-based helper functions to replace the radix tree based
metaphors currently in use. The biggest change is that converted code
doesn't see its own lock bit; get_unlocked_entry() always returns an
entry with the lock bit clear. So we don't have to mess around loading
the current entry and clearing the lock bit; we can just store the
unlocked entry that we already have.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Since the XArray is embedded in the struct address_space, its address
contains exactly as much entropy as the address of the mapping. This
patch is purely preparatory for later patches which will simplify the
wait/wake interfaces.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
This is close to a 1:1 replacement of radix tree APIs with their XArray
equivalents. It would be possible to optimise nilfs_copy_back_pages(),
but that doesn't seem to be in the performance path. Also, I think
it has a pre-existing bug, and I've added a note to that effect in the
source code.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
The page cache offers the ability to search for a miss in the previous or
next N locations. Rather than teach the XArray about the page cache's
definition of a miss, use xas_prev() and xas_next() to search the page
array. This should be more efficient as it does not have to start the
lookup from the top for each index.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
At inode.c:evict_inode_truncate_pages(), when we iterate over the
inode's extent states, we access an extent state record's "state" field
after we unlocked the inode's io tree lock. This can lead to a
use-after-free issue because after we unlock the io tree that extent
state record might have been freed due to being merged into another
adjacent extent state record (a previous inflight bio for a read
operation finished in the meanwhile which unlocked a range in the io
tree and cause a merge of extent state records, as explained in the
comment before the while loop added in commit 6ca0709756 ("Btrfs: fix
hang during inode eviction due to concurrent readahead")).
Fix this by keeping a copy of the extent state's flags in a local
variable and using it after unlocking the io tree.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201189
Fixes: b9d0b38928 ("btrfs: Add handler for invalidate page")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This could result in a really bad case where we do something like
evict
evict_refill_and_join
btrfs_commit_transaction
btrfs_run_delayed_iputs
evict
evict_refill_and_join
btrfs_commit_transaction
... forever
We have plenty of other places where we run delayed iputs that are much
safer, let those do the work.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We were not handling the reserved byte accounting properly for data
references. Metadata was fine, if it errored out the error paths would
free the bytes_reserved count and pin the extent, but it even missed one
of the error cases. So instead move this handling up into
run_one_delayed_ref so we are sure that both cases are properly cleaned
up in case of a transaction abort.
CC: stable@vger.kernel.org # 4.18+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we insert the file extent once the ordered extent completes we free
the reserved extent reservation as it'll have been migrated to the
bytes_used counter. However if we error out after this step we'll still
clear the reserved extent reservation, resulting in a negative
accounting of the reserved bytes for the block group and space info.
Fix this by only doing the free if we didn't successfully insert a file
extent for this extent.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
max_extent_size is supposed to be the largest contiguous range for the
space info, and ctl->free_space is the total free space in the block
group. We need to keep track of these separately and _only_ use the
max_free_space if we don't have a max_extent_size, as that means our
original request was too large to search any of the block groups for and
therefore wouldn't have a max_extent_size set.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We can't use entry->bytes if our entry is a bitmap entry, we need to use
entry->max_extent_size in that case. Fix up all the logic to make this
consistent.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we use up our block group before allocating a new one we'll easily
get a max_extent_size that's set really really low, which will result in
a lot of fragmentation. We need to make sure we're resetting the
max_extent_size when we add a new chunk or add new space.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlvDdvgACgkQJWrqGEe9
VoQ0zQf/QfXYjLDbC/1FXckEkEeVZPRbXQMf+ptdTo0inJefy9LMOvhRKmuABCxn
wwPa99aqQ+aHESnU/s2d8FUrhNRUf35lmRIAP512lJk79tBfgo73l5WSc6UTg6hO
w3KbigOvTi7wCKQYGDFOBZuoFFCvpNsIEtWFuodCbYG1GmeAaL7L2fhbri9JbcE2
zPqmCv0w5BUrPR7i/taI5gD+KDtRdmCEyfb7wQoJy2XZVO0SKqGsBhDhYWqwCpck
eP2UzQ4cFT8X1S0/AfUpbowc6cftdqIwW9VRY4inx3ALQ+sKxrkJ+0E3gL9lnZ+F
p/is0gTdvDmnOjXfwGcL7GXGy0nN8Q==
=EKv1
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.20' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
We don't need to call this in the direct, read, or pnfs resend paths and
the only other caller is the write path in nfs_page_async_flush() which
already checks and sets the pg_error on the context.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
We must check pg_error and call error_cleanup after any call to pg_doio.
Currently, we are skipping the unlock of a page if we encounter an error in
nfs_pageio_complete() before handing off the work to the RPC layer.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If a slab cache object is allocated, it needs to be freed eventually,
certainly before anyone unloads the module that allocated it.
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
fscache_set_key() can incur an out-of-bounds read, reported by KASAN:
BUG: KASAN: slab-out-of-bounds in fscache_alloc_cookie+0x5b3/0x680 [fscache]
Read of size 4 at addr ffff88084ff056d4 by task mount.nfs/32615
and also reported by syzbot at https://lkml.org/lkml/2018/7/8/236
BUG: KASAN: slab-out-of-bounds in fscache_set_key fs/fscache/cookie.c:120 [inline]
BUG: KASAN: slab-out-of-bounds in fscache_alloc_cookie+0x7a9/0x880 fs/fscache/cookie.c:171
Read of size 4 at addr ffff8801d3cc8bb4 by task syz-executor907/4466
This happens for any index_key_len which is not divisible by 4 and is
larger than the size of the inline key, because the code allocates exactly
index_key_len for the key buffer, but the hashing loop is stepping through
it 4 bytes (u32) at a time in the buf[] array.
Fix this by calculating how many u32 buffers we'll need by using
DIV_ROUND_UP, and then using kcalloc() to allocate a precleared allocation
buffer to hold the index_key, then using that same count as the hashing
index limit.
Fixes: ec0328e46d ("fscache: Maintain a catalogue of allocated cookies")
Reported-by: syzbot+a95b989b2dde8e806af8@syzkaller.appspotmail.com
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline key in struct rxrpc_cookie is insufficiently initialized,
zeroing only 3 of the 4 slots, therefore an index_key_len between 13 and 15
bytes will end up hashing uninitialized memory because the memcpy only
partially fills the last buf[] element.
Fix this by clearing fscache_cookie objects on allocation rather than using
the slab constructor to initialise them. We're going to pretty much fill
in the entire struct anyway, so bringing it into our dcache writably
shouldn't incur much overhead.
This removes the need to do clearance in fscache_set_key() (where we aren't
doing it correctly anyway).
Also, we don't need to set cookie->key_len in fscache_set_key() as we
already did it in the only caller, so remove that.
Fixes: ec0328e46d ("fscache: Maintain a catalogue of allocated cookies")
Reported-by: syzbot+a95b989b2dde8e806af8@syzkaller.appspotmail.com
Reported-by: Eric Sandeen <sandeen@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the victim might've been rmdir'ed just before the lock_rename();
unlike the normal callers, we do not look the source up after the
parents are locked - we know it beforehand and just recheck that it's
still the child of what used to be its parent. Unfortunately,
the check is too weak - we don't spot a dead directory since its
->d_parent is unchanged, dentry is positive, etc. So we sail all
the way to ->rename(), with hosting filesystems _not_ expecting
to be asked renaming an rmdir'ed subdirectory.
The fix is easy, fortunately - the lock on parent is sufficient for
making IS_DEADDIR() on child safe.
Cc: stable@vger.kernel.org
Fixes: 9ae326a690 (CacheFiles: A cache that backs onto a mounted filesystem)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the typical unmount case, the AIL is forced out by the unmount
sequence before the xfsaild task is stopped. Since AIL items are
removed on writeback completion, this means that the AIL
->ail_buf_list delwri queue has been drained. This is not always
true in the shutdown case, however.
It's possible for buffers to sit on a delwri queue for a period of
time across submission attempts if said items are locked or have
been relogged and pinned since first added to the queue. If the
attempt to log such an item results in a log I/O error, the error
processing can shutdown the fs, remove the item from the AIL, stale
the buffer (dropping the LRU reference) and clear its delwri queue
state. The latter bit means the buffer will be released from a
delwri queue on the next submission attempt, but this might never
occur if the filesystem has shutdown and the AIL is empty.
This means that such buffers are held indefinitely by the AIL delwri
queue across destruction of the AIL. Aside from being a memory leak,
these buffers can also hold references to in-core perag structures.
The latter problem manifests as a generic/475 failure, reproducing
the following asserts at unmount time:
XFS: Assertion failed: atomic_read(&pag->pag_ref) == 0,
file: fs/xfs/xfs_mount.c, line: 151
XFS: Assertion failed: atomic_read(&pag->pag_ref) == 0,
file: fs/xfs/xfs_mount.c, line: 132
To prevent this problem, clear the AIL delwri queue as a final step
before xfsaild() exit. The !empty state should never occur in the
normal case, so add an assert to catch unexpected problems going
forward.
[dgc: add comment explaining need for xfs_buf_delwri_cancel() after
calling xfs_buf_delwri_submit_nowait().]
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Most offset macro mess is used in xfs_stats_format() only, and we can
simply get the right offsets using offsetof(), instead of several macros
to mark the offsets inside __xfsstats structure.
Replace all XFSSTAT_END_* macros by a single helper macro to get the
right offset into __xfsstats, and use this helper in xfs_stats_format()
directly.
The quota stats code, still looks a bit cleaner when using XFSSTAT_*
macros, so, this patch also defines XFSSTAT_START_XQMSTAT and
XFSSTAT_END_XQMSTAT locally to that code. This also should prevent
offset mistakes when updates are done into __xfsstats.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The addition of FIBT, RMAP and REFCOUNT changed the offsets into
__xfssats structure.
This caused xqmstat_proc_show() to display garbage data via
/proc/fs/xfs/xqmstat, once it relies on the offsets marked via macros.
Fix it.
Fixes: 00f4e4f9 xfs: add rmap btree stats infrastructure
Fixes: aafc3c24 xfs: support the XFS_BTNUM_FINOBT free inode btree type
Fixes: 46eeb521 xfs: introduce refcount btree definitions
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When looking at a 4.18 based KASAN use after free report, I noticed
that racing xfs_buf_rele() may race on dropping the last reference
to the buffer and taking the buffer lock. This was the symptom
displayed by the KASAN report, but the actual issue that was
reported had already been fixed in 4.19-rc1 by commit e339dd8d8b
("xfs: use sync buffer I/O for sync delwri queue submission").
Despite this, I think there is still an issue with xfs_buf_rele()
in this code:
release = atomic_dec_and_lock(&bp->b_hold, &pag->pag_buf_lock);
spin_lock(&bp->b_lock);
if (!release) {
.....
If two threads race on the b_lock after both dropping a reference
and one getting dropping the last reference so release = true, we
end up with:
CPU 0 CPU 1
atomic_dec_and_lock()
atomic_dec_and_lock()
spin_lock(&bp->b_lock)
spin_lock(&bp->b_lock)
<spins>
<release = true bp->b_lru_ref = 0>
<remove from lists>
freebuf = true
spin_unlock(&bp->b_lock)
xfs_buf_free(bp)
<gets lock, reading and writing freed memory>
<accesses freed memory>
spin_unlock(&bp->b_lock) <reads/writes freed memory>
IOWs, we can't safely take bp->b_lock after dropping the hold
reference because the buffer may go away at any time after we
drop that reference. However, this can be fixed simply by taking the
bp->b_lock before we drop the reference.
It is safe to nest the pag_buf_lock inside bp->b_lock as the
pag_buf_lock is only used to serialise against lookup in
xfs_buf_find() and no other locks are held over or under the
pag_buf_lock there. Make this clear by documenting the buffer lock
orders at the top of the file.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch adds xfs_attr_remove_args. These sub-routines remove
the attributes specified in @args. We will use this later for setting
parent pointers as a deferred attribute operation.
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch adds xfs_attr_set_args and xfs_bmap_set_attrforkoff.
These sub-routines set the attributes specified in @args.
We will use this later for setting parent pointers as a deferred
attribute operation.
[dgc: remove attr fork init code from xfs_attr_set_args().]
[dgc: xfs_attr_try_sf_addname() NULLs args.trans after commit.]
[dgc: correct sf add error handling.]
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch adds a subroutine xfs_attr_try_sf_addname
used by xfs_attr_set. This subrotine will attempt to
add the attribute name specified in args in shortform,
as well and perform error handling previously done in
xfs_attr_set.
This patch helps to pre-simplify xfs_attr_set for reviewing
purposes and reduce indentation. New function will be added
in the next patch.
[dgc: moved commit to helper function, too.]
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch moves fs/xfs/xfs_attr.h to fs/xfs/libxfs/xfs_attr.h
since xfs_attr.c is in libxfs. We will need these later in
xfsprogs.
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The kernel only issues a log message that it's been shut down when
the filesystem triggers a shutdown itself. Hence there is no trace
in the log when a shutdown is triggered manually from userspace.
This can make it hard to see sequence of events in the log when
things go wrong, so make sure we always log a message when a
shutdown is run.
While there, clean up the logic flow so we don't have to continually
check if the shutdown trigger was user initiated before logging
shutdown messages.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We don't handle buffer state properly in online repair's findroot
routine. If a buffer already has b_ops set, we don't ever want to touch
that, and we don't want to call the read verifiers on a buffer that
could be dirty (CRCs are only recomputed during log checkpoints).
Therefore, be more careful about what we do with a buffer -- if someone
else already attached ops that are not the ones for this btree type,
just ignore the buffer. We only attach our btree type's buf ops if it
matches the magic/uuid and structure checks.
We also modify xfs_buf_read_map to allow callers to set buffer ops on a
DONE buffer with NULL ops so that repair doesn't leave behind buffers
which won't have buffers attached to them.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
If a caller supplies buffer ops when trying to read a buffer and the
buffer doesn't already have buf ops assigned, ensure that the ops are
assigned to the buffer and the verifier is run on that buffer.
Note that current XFS code is careful to assign buffer ops after a
xfs_{trans_,}buf_read call in which ops were not supplied. However, we
should apply ops defensively in case there is ever a coding mistake; and
an upcoming repair patch will need to be able to read a buffer without
assigning buf ops.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
In xrep_findroot_block, if we find a candidate root block with sibling
pointers or sibling blocks on the same tree level, we should not return
that block as a tree root because root blocks cannot have siblings.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Needed by userspace programs that call fstatfs().
It'd be natural to publish XFS_SB_MAGIC in uapi, but while these two
have identical values, they have different semantic meaning: one is
an enum cookie meant for statfs, the other a signature of the
on-disk format.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Instead of just asserting that we have no delalloc space dangling
in an inode that gets freed print the actual offenders for debug
mode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We should want to write directly into the data fork for blocks that don't
have an extent in the COW fork covering them yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We only need to allocate blocks for zeroing for reflink inodes,
and for we currently have a special case for reflink files in
the otherwise direct I/O path that I'd like to get rid of.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The option to enable unwritten extents was made default in 2003,
removed from mkfs in 2007, and cannot be disabled in v5. We also
rely on it for a lot of common functionality, so filesystems without
it will run a completely untested and buggy code path. Enabling the
support also is a simple bit flip using xfs_db, so legacy file
systems can still be brought forward.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The invalid state isn't any different from a hole, so merge the two
states. Use the more descriptive hole name, but keep it as the first
value of the enum to catch uninitialized fields.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
There are some cases can cause memory leak when parsing
option 'osdname'.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Assigning value -EINVAL to "retval" here, but that stored value is
overwritten before it can be used.
retval = -EINVAL;
....
retval = rw_verify_area(WRITE, out.file, &out_pos, count);
value_overwrite: Overwriting previous write to "retval" with value
from rw_verify_area
delete invalid assignment statements
Signed-off-by: n00202754 <nixiaoming@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Right now we return EINVAL if a process does not have permission to dedupe a
file. This was an oversight on my part. EPERM gives a true description of
the nature of our error, and EINVAL is already used for the case that the
filesystem does not support dedupe.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The permission check in vfs_dedupe_file_range_one() is too coarse - We only
allow dedupe of the destination file if the user is root, or they have the
file open for write.
This effectively limits a non-root user from deduping their own read-only
files. In addition, the write file descriptor that the user is forced to
hold open can prevent execution of files. As file data during a dedupe
does not change, the behavior is unexpected and this has caused a number of
issue reports. For an example, see:
https://github.com/markfasheh/duperemove/issues/129
So change the check so we allow dedupe on the target if:
- the root or admin is asking for it
- the process has write access
- the owner of the file is asking for the dedupe
- the process could get write access
That way users can open read-only and still get dedupe.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The find_ref_head shouldn't return the first entry even if no exact match
is found. So move the hidden behavior to higher level.
Besides, remove the useless local variables in the btrfs_select_ref_head.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com>
[ reformat comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
When writing out a block group free space cache we can end deadlocking
with ourselves on an extent buffer lock resulting in a warning like the
following:
[245043.379979] WARNING: CPU: 4 PID: 2608 at fs/btrfs/locking.c:251 btrfs_tree_lock+0x1be/0x1d0 [btrfs]
[245043.392792] CPU: 4 PID: 2608 Comm: btrfs-transacti Tainted: G
W I 4.16.8 #1
[245043.395489] RIP: 0010:btrfs_tree_lock+0x1be/0x1d0 [btrfs]
[245043.396791] RSP: 0018:ffffc9000424b840 EFLAGS: 00010246
[245043.398093] RAX: 0000000000000a30 RBX: ffff8807e20a3d20 RCX: 0000000000000001
[245043.399414] RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff8807e20a3d20
[245043.400732] RBP: 0000000000000001 R08: ffff88041f39a700 R09: ffff880000000000
[245043.402021] R10: 0000000000000040 R11: ffff8807e20a3d20 R12: ffff8807cb220630
[245043.403296] R13: 0000000000000001 R14: ffff8807cb220628 R15: ffff88041fbdf000
[245043.404780] FS: 0000000000000000(0000) GS:ffff88082fc80000(0000) knlGS:0000000000000000
[245043.406050] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[245043.407321] CR2: 00007fffdbdb9f10 CR3: 0000000001c09005 CR4: 00000000000206e0
[245043.408670] Call Trace:
[245043.409977] btrfs_search_slot+0x761/0xa60 [btrfs]
[245043.411278] btrfs_insert_empty_items+0x62/0xb0 [btrfs]
[245043.412572] btrfs_insert_item+0x5b/0xc0 [btrfs]
[245043.413922] btrfs_create_pending_block_groups+0xfb/0x1e0 [btrfs]
[245043.415216] do_chunk_alloc+0x1e5/0x2a0 [btrfs]
[245043.416487] find_free_extent+0xcd0/0xf60 [btrfs]
[245043.417813] btrfs_reserve_extent+0x96/0x1e0 [btrfs]
[245043.419105] btrfs_alloc_tree_block+0xfb/0x4a0 [btrfs]
[245043.420378] __btrfs_cow_block+0x127/0x550 [btrfs]
[245043.421652] btrfs_cow_block+0xee/0x190 [btrfs]
[245043.422979] btrfs_search_slot+0x227/0xa60 [btrfs]
[245043.424279] ? btrfs_update_inode_item+0x59/0x100 [btrfs]
[245043.425538] ? iput+0x72/0x1e0
[245043.426798] write_one_cache_group.isra.49+0x20/0x90 [btrfs]
[245043.428131] btrfs_start_dirty_block_groups+0x102/0x420 [btrfs]
[245043.429419] btrfs_commit_transaction+0x11b/0x880 [btrfs]
[245043.430712] ? start_transaction+0x8e/0x410 [btrfs]
[245043.432006] transaction_kthread+0x184/0x1a0 [btrfs]
[245043.433341] kthread+0xf0/0x130
[245043.434628] ? btrfs_cleanup_transaction+0x4e0/0x4e0 [btrfs]
[245043.435928] ? kthread_create_worker_on_cpu+0x40/0x40
[245043.437236] ret_from_fork+0x1f/0x30
[245043.441054] ---[ end trace 15abaa2aaf36827f ]---
This is because at write_one_cache_group() when we are COWing a leaf from
the extent tree we end up allocating a new block group (chunk) and,
because we have hit a threshold on the number of bytes reserved for system
chunks, we attempt to finalize the creation of new block groups from the
current transaction, by calling btrfs_create_pending_block_groups().
However here we also need to modify the extent tree in order to insert
a block group item, and if the location for this new block group item
happens to be in the same leaf that we were COWing earlier, we deadlock
since btrfs_search_slot() tries to write lock the extent buffer that we
locked before at write_one_cache_group().
We have already hit similar cases in the past and commit d9a0540a79
("Btrfs: fix deadlock when finalizing block group creation") fixed some
of those cases by delaying the creation of pending block groups at the
known specific spots that could lead to a deadlock. This change reworks
that commit to be more generic so that we don't have to add similar logic
to every possible path that can lead to a deadlock. This is done by
making __btrfs_cow_block() disallowing the creation of new block groups
(setting the transaction's can_flush_pending_bgs to false) before it
attempts to allocate a new extent buffer for either the extent, chunk or
device trees, since those are the trees that pending block creation
modifies. Once the new extent buffer is allocated, it allows creation of
pending block groups to happen again.
This change depends on a recent patch from Josef which is not yet in
Linus' tree, named "btrfs: make sure we create all new block groups" in
order to avoid occasional warnings at btrfs_trans_release_chunk_metadata().
Fixes: d9a0540a79 ("Btrfs: fix deadlock when finalizing block group creation")
CC: stable@vger.kernel.org # 4.4+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199753
Link: https://lore.kernel.org/linux-btrfs/CAJtFHUTHna09ST-_EEiyWmDH6gAqS6wa=zMNMBsifj8ABu99cw@mail.gmail.com/
Reported-by: E V <eliventer@gmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When using the NO_HOLES feature and logging a regular file, we were
expecting that if we find an inline extent, that either its size in RAM
(uncompressed and unenconded) matches the size of the file or if it does
not, that it matches the sector size and it represents compressed data.
This assertion does not cover a case where the length of the inline extent
is smaller than the sector size and also smaller the file's size, such
case is possible through fallocate. Example:
$ mkfs.btrfs -f -O no-holes /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0xb60 0 21" /mnt/foobar
$ xfs_io -c "falloc 40 40" /mnt/foobar
$ xfs_io -c "fsync" /mnt/foobar
In the above example we trigger the assertion because the inline extent's
length is 21 bytes while the file size is 80 bytes. The fallocate() call
merely updated the file's size and did not touch the existing inline
extent, as expected.
So fix this by adjusting the assertion so that an inline extent length
smaller than the file size is valid if the file size is smaller than the
filesystem's sector size.
A test case for fstests follows soon.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Fixes: a89ca6f24f ("Btrfs: fix fsync after truncate when no_holes feature is enabled")
CC: stable@vger.kernel.org # 4.14+
Link: https://lore.kernel.org/linux-btrfs/CAE5jQCfRSBC7n4pUTFJcmHh109=gwyT9mFkCOL+NKfzswmR=_Q@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At inode.c:compress_file_range(), under the "free_pages_out" label, we can
end up dereferencing the "pages" pointer when it has a NULL value. This
case happens when "start" has a value of 0 and we fail to allocate memory
for the "pages" pointer. When that happens we jump to the "cont" label and
then enter the "if (start == 0)" branch where we immediately call the
cow_file_range_inline() function. If that function returns 0 (success
creating an inline extent) or an error (like -ENOMEM for example) we jump
to the "free_pages_out" label and then access "pages[i]" leading to a NULL
pointer dereference, since "nr_pages" has a value greater than zero at
that point.
Fix this by setting "nr_pages" to 0 when we fail to allocate memory for
the "pages" pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201119
Fixes: 771ed689d2 ("Btrfs: Optimize compressed writeback and reads")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This doesn't work on stacked devices, and it doesn't work on
blk-mq devices. The request_list is only used on legacy, which
we don't have much of anymore, and soon won't have any of.
Kill the check.
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Steve French