The field mspi->reg_base is annotated as an __iomem pointer. Good.
However, this field is often assigned to a temporary variable:
before being used. For example:
struct fsl_spi_reg *reg_base = mspi->reg_base;
But this variable is missing the __iomem annotation.
So, add the missing __iomem and make sparse & the bot happier.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Link: https://lore.kernel.org/r/20200622162611.83694-1-luc.vanoostenryck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The blind and counted loops are always called with nonzero count, so
convert them to do-while loops that lead to slightly more efficient
code generation. With GCC 8.3 this shaves off 1-2 instructions per
iteration in each case.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/9242863077acf9a64e4b3720e479855b88d19e82.1592261248.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ handler only needs the struct spi_controller for the sake of
the completion at the end of a transfer. Passing the struct bcm2835_spi
directly as the IRQ data allows that level of indirection to be pushed
into the completion path for the reverse lookup, and avoided entirely
in all other cases.
This saves one explicit load in the critical path, plus (for a GCC 8.3
build) two registers worth of stack frame overhead.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/6b401cb521539caffab21f05b4c8cba6c9d27c6e.1592261248.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMAP2 MCSPI has some kind of half-baked GPIO CS support:
it includes code like this:
if (gpio_is_valid(spi->cs_gpio)) {
ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
(...)
But it doesn't parse the "cs-gpios" attribute in the device
tree to count the number of GPIOs or pick out the GPIO numbers
and put these in the SPI master's .cs_gpios property.
We complete the implementation of supporting CS GPIOs
from the device tree and switch it over to use the SPI core
for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200625231257.280615-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the chip select on the Qualcomm geni SPI controller isn't
exactly cheap. Let's cache the current setting and avoid setting the
chip select if it's already right.
Using "flashrom" to read or write the EC firmware on a Chromebook
shows roughly a 25% reduction in interrupts and a 15% speedup.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626151946.1.I06134fd669bf91fd387dc6ecfe21d44c202bd412@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
A batch of fixes for the Freescale DSPI driver fixing some serious
issues with removal of active devices and one resume case, plus a few
new PCI IDs for Intel platforms.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl76FzkTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0C5iB/0ThW3V0f9NKiIPkJjgp4DYfhYL8cKO
z4fOeOdJHOm73Atd5efhfU58REpEjmAD76O++/z4qD1l5wRsfILCObEsMwPYRTzr
gYlFVaNuZ3wAz8rDYU7VfmdzuZKRfhAUxJKovcLJleBmWAsGk3fHd5oBPVNJQPl3
jx1Wnj37T2dykI+jhRjQuRbN4e+1FxOKNHcVmwkoUx9OKX1cbRczE5mYhPf8zD2K
ZMMlfuyPg1zqfsVRzBSjaqsbMLZY4tgYemwQmLthhMvMZJ1cw4bt1RMgVBKlzPZN
X+vr5vh9HA8y6spJoAfffBCtIr7BVsNpXXi11QMozZ6YgnBUSJDZeN8Q
=OauP
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A batch of fixes for the Freescale DSPI driver fixing some serious
issues with removal of active devices and one resume case, plus a few
new PCI IDs for Intel platforms"
* tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Add support for Intel Tiger Lake PCH-H
spi: spi-fsl-dspi: Initialize completion before possible interrupt
spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths
spi: spi-fsl-dspi: Fix lockup if device is shutdown during SPI transfer
spi: spi-fsl-dspi: Fix lockup if device is removed during SPI transfer
geni spi needs to express a perforamnce state requirement on CX
depending on the frequency of the clock rates. Use OPP table from
DT to register with OPP framework and use dev_pm_opp_set_rate() to
set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/1592222564-13556-3-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get the interconnect paths for QSPI device and vote according to the
current bus speed of the driver.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-8-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get the interconnect paths for SPI based Serial Engine device
and vote according to the current bus speed of the driver.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1592908737-7068-7-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There is code for adjusting the clock both in setup_fifo_params()
(called from prepare_message()) and in setup_fifo_xfer() (called from
transfer_one()). The code is the same. Abstract it out to a shared
function.
This is a no-op cleanup patch. The only change is to the error string
if we fail to set the clock. Since the two paths has marginally
different error messages I picked the clean one.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1592908737-7068-6-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the MODULE_DEVICE_TABLE macro for the platform_device_id table to
allow proper creation of modalias strings and fix autoloading module for
this driver.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/1592962286-25752-3-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is expected to support device ID "spi_altera" for MMIO accessed
devices, device ID "subdev_spi_altera" for indirect accessed devices. But
the platform bus will not try driver name match anymore if the platform
driver has an id_table. So the "spi_altera" should also be added to
id_table.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/1592962286-25752-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback pio feature in case dma transfer failed before start.
Besides, another whole pio transfer including setup_transfer will be
issued by spi core, no need to restore jobs like commit bcd8e7761e ("spi:
imx: fallback to PIO if dma setup failure").
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-3-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add fallback to pio mode in case dma transfer failed with error status
SPI_TRANS_FAIL_NO_START.
If spi client driver want to enable this feature please set xfer->error in
the proper place such as dmaengine_prep_slave_sg() failure detect(but no
any data put into spi bus yet). Besides, add master->fallback checking in
its can_dma() so that spi core could switch to pio next time. Please refer
to spi-imx.c.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-2-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of fixes here for no single reason. There's a collection of
the usual sort of device specific fixes and also a bunch of people have
been working on spidev and the userspace test program spidev_test so
they've got an unusually large collection of small fixes.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl7wl/8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NJBB/4oTOxPIfkKQyPcSTQB8FC6AHJ5Z8FT
/4dtK4U32rn5Sms/CHNXMMFxomBgB46Ud19KJ/bEgqugJfI9Vl0bl9fZT+sDyVU3
rFPthVluIprFe1bITyfcgYmjRoznLRdzj9LMFsAWIe3Vmy584TdvXbl8n5COu5Wh
6sR6SuQnEn65x1HC4++3IsG70+ogz81sFRapk/7jXwS+YdwzWIqtN2s2IlUcTmcy
ylijl04XUSyo6e/v/sjZaaRmIz72mW+HbMKW4iC0mGZ6yuACoy7zop9BuwAg6S7z
dFDyqTZ5gq72ZeJc7fuco1y7jqQoKUC1oTRghPlbq2XG3Huta80l415l
=32lr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Quite a lot of fixes here for no single reason.
There's a collection of the usual sort of device specific fixes and
also a bunch of people have been working on spidev and the userspace
test program spidev_test so they've got an unusually large collection
of small fixes"
* tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: fix a potential use-after-free in spidev_release()
spi: spidev: fix a race between spidev_release and spidev_remove
spi: stm32-qspi: Fix error path in case of -EPROBE_DEFER
spi: uapi: spidev: Use TABs for alignment
spi: spi-fsl-dspi: Free DMA memory with matching function
spi: tools: Add macro definitions to fix build errors
spi: tools: Make default_tx/rx and input_tx static
spi: dt-bindings: amlogic, meson-gx-spicc: Fix schema for meson-g12a
spi: rspi: Use requested instead of maximum bit rate
spi: spidev_test: Use %u to format unsigned numbers
spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH
To follow onto Doug's latest spi geni series[1] this simplifies and
reduces the code a little more.
[1] https://lore.kernel.org/r/20200618150626.237027-1-dianders@chromium.org
Stephen Boyd (2):
spi: spi-geni-qcom: Simplify setup_fifo_xfer()
spi: spi-geni-qcom: Don't set {tx,rx}_rem_bytes unnecessarily
drivers/spi/spi-geni-qcom.c | 55 +++++++++++++++++--------------------
1 file changed, 25 insertions(+), 30 deletions(-)
base-commit: 7ba9bdcb91
--
Sent by a computer, using git, on the internet
We only need to test for these counters being non-zero when we see the
end of a transfer. If we're doing a CS change then they will already be
zero. This implies that we don't need to set these to 0 if we're
cancelling an in flight transfer too, because we only care to test these
counters when the 'DONE' bit is set in the hardware and we've set them
to non-zero for a transfer.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of SPI_FULL_DUPLEX (3) is really SPI_TX_ONLY (1) ORed
with SPI_RX_ONLY (2). Let's drop the define and simplify the code here a
bit by collapsing the setting of 'm_cmd' into conditions that are the
same.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handler calls completion and is IRQ requested before the
completion is initialized. Logically it should be the other way.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During shutdown, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
shutdown reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: dc23482599 ("spi: spi-fsl-dspi: Adding shutdown hook")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: 05209f4570 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of SPI_FULL_DUPLEX (3) is really SPI_TX_ONLY (1) ORed
with SPI_RX_ONLY (2). Let's drop the define and simplify the code here a
bit by collapsing the setting of 'm_cmd' into conditions that are the
same.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200618233959.160032-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<vadivel.muruganx.ramuthevar@linux.intel.com> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Resend v3:
Rebased onto v5.7-c1
v3:
Split handling of probe deferral into separate patch (out of 5/6)
Split dropping of redundant WREN to separate patch (out of 5/6)
Fix a possible memleak due to lack of spi_master_put()
Parse all SPI slave nodes in cqspi_setup_flash()
Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next
v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.
Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/
Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path
drivers/mtd/spi-nor/controllers/Kconfig | 11 -
drivers/mtd/spi-nor/controllers/Makefile | 1 -
drivers/spi/Kconfig | 11 +
drivers/spi/Makefile | 1 +
.../spi-cadence-quadspi.c} | 541 +++++++-----------
5 files changed, 222 insertions(+), 343 deletions(-)
rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
base-commit: b3a9e3b962
--
2.26.2
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Updated the regmap & indirect access support for spi-altera.
Patch #1 is an 1:1 replacement of of readl/writel with regmap_read/write
Patch #2 introduced a new platform_device_id to support indirect access as
a sub device.
Patch #3 is a minor fix.
Main changes from v1:
- Split the regmap supporting patch to 2 patches.
- Add a new platform_device_id to support indirect access.
- Removed the v1 patch "move driver name string to header file". Now we
use driver name string directly.
- Add Yilun's Signed-off-by for Patch #3.
- Add Tom's Reviewed-by.
Matthew Gerlach (1):
spi: altera: fix size mismatch on 64 bit processors
Xu Yilun (2):
spi: altera: use regmap-mmio instead of direct mmio register access
spi: altera: support indirect access to the registers
drivers/spi/Kconfig | 1 +
drivers/spi/spi-altera.c | 127 +++++++++++++++++++++++++++++++++++++++--------
2 files changed, 107 insertions(+), 21 deletions(-)
--
2.7.4
This patch series is a new version of the previous patch posted:
[PATCH v2] spi: spi-geni-qcom: Speculative fix of "nobody cared" about interrupt
https://lore.kernel.org/r/20200317133653.v2.1.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid
At this point I've done enough tracing to know that there was a real
race in the old code (not just weakly ordered memory problems) and
that should be fixed with the locking patches.
While looking at this driver, I also noticed we weren't properly
noting error interrupts and also weren't actually using our FIFO
effectively, so I fixed those.
The last patch in the series addresses review feedback about dislike
for the "cur_mcmd" state variable. It also could possibly make
"abort" work ever-so-slightly more reliably.
Changes in v4:
- Drop 'controller' in comment.
- Use Stephen's diagram to explain the race better.
Changes in v3:
- ("spi: spi-geni-qcom: No need for irqsave variant...") new for v3
- Split out some lock cleanup to previous patch.
- Don't need to read IRQ status register inside spinlock.
- Don't check for state CMD_NONE; later patch is removing state var.
- Don't hold the lock for all of setup_fifo_xfer().
- Comment about why it's safe to Ack interrupts at the end.
- Subject/desc changed since race is definitely there.
- ("spi: spi-geni-qcom: Check for error IRQs") new in v3.
- ("spi: spi-geni-qcom: Actually use our FIFO") new in v3.
- ("spi: spi-geni-qcom: Don't keep a local state variable") new in v3.
Changes in v2:
- Detect true spurious interrupt.
- Still return IRQ_NONE for state machine mismatch, but print warn.
Douglas Anderson (5):
spi: spi-geni-qcom: No need for irqsave variant of spinlock calls
spi: spi-geni-qcom: Mo' betta locking
spi: spi-geni-qcom: Check for error IRQs
spi: spi-geni-qcom: Actually use our FIFO
spi: spi-geni-qcom: Don't keep a local state variable
drivers/spi/spi-geni-qcom.c | 120 ++++++++++++++++++++++++------------
1 file changed, 81 insertions(+), 39 deletions(-)
--
2.27.0.290.gba653c62da-goog
The variable "cur_mcmd" kept track of our current state (idle, xfer,
cs, cancel). We don't really need it, so get rid of it. Instead:
* Use separate condition variables for "chip select done", "cancel
done", and "abort done". This is important so that if a "done"
comes through (perhaps some previous interrupt finally came through)
it can't confuse the cancel/abort function.
* Use the "done" interrupt only for when a chip select or transfer is
done and we can tell the difference by looking at whether "cur_xfer"
is NULL.
This is mostly a no-op change. However, it is possible it could fix
an issue where a super delayed interrupt for a cancel command could
have confused our waiting for an abort command.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.5.Ib1e6855405fc9c99916ab7c7dee84d73a8bf3d68@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The geni hardware has a FIFO that can hold up to 64 bytes (it has 16
entries that can hold 4 bytes each), at least on the two SoCs I tested
(sdm845 and sc7180). We configured our RX Watermark to 0, which
basically meant we got an interrupt as soon as the first 4 bytes
showed up in the FIFO. Tracing the IRQ handler showed that we often
only read 4 or 8 bytes per IRQ handler.
I tried setting the RX Watermark to "fifo size - 2" but that just got
me a bunch of overrun errors reported. Setting it to "fifo size - 3"
seemed to work great, though. This made me worried that we'd start
getting overruns if we had long interrupt latency, but that doesn't
appear to be the case and delays inserted in the IRQ handler while
using "fifo size - 3" didn't cause any errors. Presumably there is
some interaction with the poorly-documented RFR (ready for receive)
level means that "fifo size - 3" is the max. We are the SPI master,
so it makes sense that there would be no problems with overruns, the
master should just stop clocking.
Despite "fifo size - 3" working, I chose "fifo size / 2" (8 entries =
32 bytes) which gives us a little extra time to get to the interrupt
handler and should reduce dead time on the SPI wires. With this
setting, I often saw the IRQ handler handle 40 bytes but sometimes up
to 56 if we had bad interrupt latency.
Testing by running "flashrom -p ec -r" on a Chromebook saw interrupts
from the SPI driver cut roughly in half. Time was roughly the same.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.4.I988281f7c6ee0ed00325559bfce7539f403da69e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
>From reading the #defines it seems like we should shout if we ever see
one of these error bits. Let's do so. This doesn't do anything
functional except print a yell in the log if the error bits are seen.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.3.Id8bebdbdb4d2ed9468634343a7e6207d6cffff8a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If you added a bit of a delay (like a trace_printk) into the ISR for
the spi-geni-qcom driver, you would suddenly start seeing some errors
spit out. The problem was that, though the ISR itself held a lock,
other parts of the driver didn't always grab the lock.
One example race was this:
CPU0 CPU1
---- ----
spi_geni_set_cs()
mas->cur_mcmd = CMD_CS;
geni_se_setup_m_cmd(...)
wait_for_completion_timeout(&xfer_done);
<INTERRUPT>
geni_spi_isr()
complete(&xfer_done);
<wakeup>
pm_runtime_put(mas->dev);
... // back to SPI core
spi_geni_transfer_one()
setup_fifo_xfer()
mas->cur_mcmd = CMD_XFER;
mas->cur_cmd = CMD_NONE; // bad!
return IRQ_HANDLED;
Let's fix this. Before we start messing with hardware, we'll grab the
lock to make sure that the IRQ handler from some previous command has
really finished. We don't need to hold the lock unless we're in a
state where more interrupts can come in, but we at least need to make
sure the previous IRQ is done. This lock is used exclusively to
prevent the IRQ handler and non-IRQ from stomping on each other. The
SPI core handles all other mutual exclusion.
As part of this, we change the way that the IRQ handler detects
spurious interrupts. Previously we checked for our state variable
being set to IRQ_NONE, but that was done outside the spinlock. We
could move it into the spinlock, but instead let's just change it to
look for the lack of any IRQ status bits being set. This can be done
outside the lock--the hardware certainly isn't grabbing or looking at
the spinlock when it updates its status register.
It's possible that this will fix real (but very rare) errors seen in
the field that look like:
irq ...: nobody cared (try booting with the "irqpoll" option)
NOTE: an alternate strategy considered here was to always make the
complete() / spi_finalize_current_transfer() the very last thing in
our IRQ handler. With such a change you could consider that we could
be "lockless". In that case, though, we'd have to be very careful w/
memory barriers so we made sure we didn't have any bugs with weakly
ordered memory. Using spinlocks makes the driver much easier to
understand.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-altera driver was originally written with a 32
bit processor, where sizeof(unsigned long) is 4. On a
64 bit processor sizeof(unsigned long) is 8. Change the structure
member to u32 to match the actual size of the control
register.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1592531021-11412-4-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for indirect access to the registers via parent
regmap.
The use case is, the spi master is a sub device of a Multifunction
device, which is connected to host by some indirect bus. To support this
device type, a new platform_device_id is introduced, and the driver tries
to get parent regmap for register accessing like many MFD sub device
drivers do.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1592531021-11412-3-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for regmap. It makes preparation for supporting
different ways to access the registers.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1592531021-11412-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an spi device is unbounded from the driver before the release
process, there will be an NULL pointer reference when it's
referenced in spi_slave_abort().
Fix it by checking it's already freed before reference.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-2-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver locks its locks in two places.
In the first usage of the lock the function doing the locking already
has a sleeping call and thus we know we can't be called from interrupt
context. That means we can use the "spin_lock_irq" variant of the
function.
In the second usage of the lock the function is the interrupt handler
and we know interrupt handlers are called with interrupts disabled.
That means we can use the "spin_lock" variant of the function.
This patch is expected to be a no-op and is just a cleanup / slight
optimization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200616034044.v3.1.Ic50cccdf27d42420a63485082f8b5bf86ed1a2b6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx arch resets the HSSPI controller at early boot. However, bmips arch
needs to perform a reset when probing the driver.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200616173235.3473149-3-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx arch resets the SPI controller at early boot. However, bmips arch
needs to perform a reset when probing the driver.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200616173235.3473149-2-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of -EPROBE_DEFER, stm32_qspi_release() was called
in any case which unregistered driver from pm_runtime framework
even if it has not been registered yet to it. This leads to:
stm32-qspi 58003000.spi: can't setup spi0.0, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@0
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@0
stm32-qspi 58003000.spi: can't setup spi0.1, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@1
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@1
On v5.7 kernel,this issue was not "visible", qspi driver was probed
successfully.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200616113035.4514-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds platform_data for spi-altera, to enable more IP
configurations, and creating specific spi client devices. It also adds
regmap support, to enable the indirect access to this IP.
We have a PCIE based FPGA platform which integrates this IP to communicate
with a BMC chip (Intel MAX10) over SPI. The IP is configured as 32bit data
width. There is also an indirect access interface in FPGA for host to
access the registers of this IP. This patchset enables this use case.
Matthew Gerlach (1):
spi: altera: fix size mismatch on 64 bit processors
Xu Yilun (5):
spi: altera: add 32bit data width transfer support.
spi: altera: add SPI core parameters support via platform data.
spi: altera: add platform data for slave information.
spi: altera: use regmap instead of direct mmio register access
spi: altera: move driver name string to header file
drivers/spi/Kconfig | 1 +
drivers/spi/spi-altera.c | 161 +++++++++++++++++++++++++++++++++++++--------
include/linux/spi/altera.h | 37 +++++++++++
3 files changed, 171 insertions(+), 28 deletions(-)
create mode 100644 include/linux/spi/altera.h
--
2.7.4
The OcteonTX (TX1/ThunderX) SPI controller does not support full
duplex transactions. Set the appropriate flag such that the spi
core will return -EINVAL on such transactions requested by chip
drivers.
This is an RFC as I need someone from Marvell/Cavium to confirm
if this driver is used for other silicon that does support
full duplex transfers (in which case we will need to identify
that we are running on the ThunderX arch before setting the flag).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Robert Richter <rrichter@marvell.com>
Link: https://lore.kernel.org/r/1590680799-5640-1-git-send-email-tharvey@gateworks.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the SPI driver for the Renesas RPC-IF. It's the "front end" driver
using the "back end" APIs in the main driver to talk to the real hardware.
We only implement the 'spi-mem' interface -- there's no need to implement
the usual SPI driver methods...
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/1ece0e6c-71af-f0f1-709e-571f4b0b4853@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx-hsspi controller is present on several BMIPS SoCs (BCM6318, BCM6328,
BCM6362 and BCM63268).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200615090943.2936839-5-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx-spi controller is present on several BMIPS SoCs (BCM6358, BCM6362,
BCM6368 and BCM63268).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200615090943.2936839-3-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces platform data for slave information, it allows
spi-altera to add new spi devices once master registration is done.
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1591845911-10197-4-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduced SPI core parameters in platform data, it
allows passing these SPI core parameters via platform data.
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1591845911-10197-3-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for 32bit width data register, then it supports 32bit
data width spi slave device and spi transfers.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1591845911-10197-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
No effective change.
Cc: broonie@kernel.org
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Driver allocates DMA memory with dma_alloc_coherent() but frees it with
dma_unmap_single().
This causes DMA warning during system shutdown (with DMA debugging) on
Toradex Colibri VF50 module:
WARNING: CPU: 0 PID: 1 at ../kernel/dma/debug.c:1036 check_unmap+0x3fc/0xb04
DMA-API: fsl-edma 40098000.dma-controller: device driver frees DMA memory with wrong function
[device address=0x0000000087040000] [size=8 bytes] [mapped as coherent] [unmapped as single]
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(unwind_backtrace) from [<8010bb34>] (show_stack+0x10/0x14)
(show_stack) from [<8011ced8>] (__warn+0xf0/0x108)
(__warn) from [<8011cf64>] (warn_slowpath_fmt+0x74/0xb8)
(warn_slowpath_fmt) from [<8017d170>] (check_unmap+0x3fc/0xb04)
(check_unmap) from [<8017d900>] (debug_dma_unmap_page+0x88/0x90)
(debug_dma_unmap_page) from [<80601d68>] (dspi_release_dma+0x88/0x110)
(dspi_release_dma) from [<80601e4c>] (dspi_shutdown+0x5c/0x80)
(dspi_shutdown) from [<805845f8>] (device_shutdown+0x17c/0x220)
(device_shutdown) from [<80143ef8>] (kernel_restart+0xc/0x50)
(kernel_restart) from [<801441cc>] (__do_sys_reboot+0x18c/0x210)
(__do_sys_reboot) from [<80100060>] (ret_fast_syscall+0x0/0x28)
DMA-API: Mapped at:
dma_alloc_attrs+0xa4/0x130
dspi_probe+0x568/0x7b4
platform_drv_probe+0x6c/0xa4
really_probe+0x208/0x348
driver_probe_device+0x5c/0xb4
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591803717-11218-1-git-send-email-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the RSPI driver always tries to use the maximum configured
bit rate for communicating with a slave device, even if the transfer(s)
in the current message specify a lower rate.
Use the mininum rate specified in the message instead.
Rename rspi_data.max_speed_hz accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH,
which would be loaded to watchdog counter once writing WDG_LOAD_LOW.
Fixes: ac17750120 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ColdFire is a big-endian cpu with a big-endian dspi hw module,
so, it uses native access, but memcpy breaks the endianness.
So, if i understand properly, by native copy we would mean
be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix
shouldn't break anything, but i couldn't test it on LS family,
so every test is really appreciated.
Fixes: 53fadb4d90 ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200529195756.184677-1-angelo.dureghello@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's better to understand what bits are set for DMA and for IRQ handling
in mid_spi_dma_setup() if they are grouped accordingly. Thus,
refactor mid_spi_dma_setup() to separate DMA and IRQ configuration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 2afccbd283 ("spi: dw: Discard static DW DMA slave structures")
did a clean up of global variables, which is fine, but messed up with
the carefully provided information in the custom DMA slave structures.
There reader can find an assignment of the DMA request lines in use.
Partially revert the above mentioned commit to restore readability
and maintainability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit ecfbd3cf3b since Lukas Wunner noticed that we
start operating on the hardware before we check to see if this is a
spurious interrupt.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru
Changelog v6:
- Provide a more detailed description of the patch:
2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion")
- Calculate the Rx delay with better accuracy by moving 4-multiplication
to the head of the formulae:
ns = 4U * NSEC_PER_SEC / dws->max_freq * nents.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Set xfer effective_speed_hz
spi: dw: Return any value retrieved from the dma_transfer callback
spi: dw: Locally wait for the DMA transfers completion
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 --
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++
.../devicetree/bindings/spi/spi-dw.txt | 24 -
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 95 ++--
drivers/spi/spi-dw-dma.c | 482 ++++++++++++++++++
drivers/spi/spi-dw-mid.c | 382 --------------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +-
drivers/spi/spi-dw.h | 20 +-
11 files changed, 719 insertions(+), 529 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
create mode 100644 drivers/spi/spi-dw-dma.c
delete mode 100644 drivers/spi/spi-dw-mid.c
--
2.26.2
Add mechanism to get the reset control and deassert it in order to bring
the IP out of reset.
Signed-off-by: Liang Jin J <liang.j.jin@ericsson.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200529155806.16758-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the common code in the spi-dw-dma.c driver is ready to be used
by the MMIO driver and now provides a method to generically (on any
DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers,
we can use it and a set of the common DW SPI DMA callbacks to enable
DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a"
devices.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't good to have numeric literals in the code especially if there
are multiple of them and they are related. Let's replace the Tx and Rx
burst level literals with the corresponding constants.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Having any data left in the Rx FIFO after the DMA engine claimed it has
finished all DMA transactions is an abnormal situation, since the DW SPI
controller driver expects to have all the data being fetched and placed
into the SPI Rx buffer at that moment. In case if that has happened we
hopefully assume that the DMA engine may still be doing the data fetching,
thus we give it sometime to finish. If after a short period of time the
data is still left in the Rx FIFO, the driver will give up waiting and
return an error indicating that the SPI controller/DMA engine must have
hung up or failed at some point of doing their duties.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since DMA transfers are performed asynchronously with actual SPI bus
transfers, then even if DMA transactions are finished it doesn't mean
all data is actually pushed to the SPI bus. Some data might still be
in the controller FIFO. This is specifically true for Tx-only transfers.
In this case if the next SPI transfer is recharged while a tail of the
previous one is still in FIFO, we'll loose that tail data. In order to
fix that problem let's add the wait procedure of the Tx SPI transfer
completion after the DMA transactions are finished.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing DW APB SSI controller doesn't support setting the exactly
requested SPI bus frequency, but only a rounded frequency determined
by means of the odd-numbered half-worded reference clock divider,
it would be good to tune the SPI core up and initialize the current
transfer effective_speed_hz. By doing so the core will be able to
execute the xfer-related delays with better accuracy.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
There is ecspi ERR009165 on i.mx6/7 soc family, which cause FIFO
transfer to be send twice in DMA mode. Please get more information from:
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf. The workaround is adding
new sdma ram script which works in XCH mode as PIO inside sdma instead
of SMC mode, meanwhile, 'TX_THRESHOLD' should be 0. The issue should be
exist on all legacy i.mx6/7 soc family before i.mx6ul.
NXP fix this design issue from i.mx6ul, so newer chips including i.mx6ul/
6ull/6sll do not need this workaroud anymore. All other i.mx6/7/8 chips
still need this workaroud. This patch set add new 'fsl,imx6ul-ecspi'
for ecspi driver and 'ecspi_fixed' in sdma driver to choose if need errata
or not.
The first two reverted patches should be the same issue, though, it
seems 'fixed' by changing to other shp script. Hope Sean or Sascha could
have the chance to test this patch set if could fix their issues.
Besides, enable sdma support for i.mx8mm/8mq and fix ecspi1 not work
on i.mx8mm because the event id is zero.
PS:
Please get sdma firmware from below linux-firmware and copy it to your
local rootfs /lib/firmware/imx/sdma.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/imx/sdma
v2:
1.Add commit log for reverted patches.
2.Add comment for 'ecspi_fixed' in sdma driver.
3.Add 'fsl,imx6sll-ecspi' compatible instead of 'fsl,imx6ul-ecspi'
rather than remove.
v3:
1.Confirm with design team make sure ERR009165 fixed on i.mx6ul/i.mx6ull
/i.mx6sll, not fixed on i.mx8m/8mm and other i.mx6/7 legacy chips.
Correct dts related dts patch in v2.
2.Clean eratta information in binding doc and new 'tx_glitch_fixed' flag
in spi-imx driver to state ERR009165 fixed or not.
3.Enlarge burst size to fifo size for tx since tx_wml set to 0 in the
errata workaroud, thus improve performance as possible.
v4:
1.Add Ack tag from Mark and Vinod
2.Remove checking 'event_id1' zero as 'event_id0'.
v5:
1.Add the last patch for compatible with the current uart driver which
using rom script, so both uart ram script and rom script supported
in latest firmware, by default uart rom script used. UART driver
will be broken without this patch.
v6:
1.Resend after rebase the latest next branch.
2.Remove below No.13~No.15 patches of v5 because they were mergered.
ARM: dts: imx6ul: add dma support on ecspi
ARM: dts: imx6sll: correct sdma compatible
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
3.Revert "dmaengine: imx-sdma: fix context cache" since
'context_loaded' removed.
v7:
1.Put the last patch 13/13 'Revert "dmaengine: imx-sdma: fix context
cache"' to the ahead of 03/13 'Revert "dmaengine: imx-sdma: refine
to load context only once" so that no building waring during comes out
during bisect.
2.Address Sascha's comments, including eliminating any i.mx6sx in this
series, adding new 'is_imx6ul_ecspi()' instead imx in imx51 and taking
care SMC bit for PIO.
3.Add back missing 'Reviewed-by' tag on 08/15(v5):09/13(v7)
'spi: imx: add new i.mx6ul compatible name in binding doc'
v8:
1.remove 0003-Revert-dmaengine-imx-sdma-fix-context-cache.patch and merge
it into 04/13 of v7
2.add 0005-spi-imx-fallback-to-PIO-if-dma-setup-failure.patch for no any
ecspi function broken even if sdma firmware not updated.
3.merge 'tx.dst_maxburst' changes in the two continous patches into one
patch to avoid confusion.
4.fix typo 'duplicated'.
Robin Gong (13):
Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core"
Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores"
Revert "dmaengine: imx-sdma: refine to load context only once"
dmaengine: imx-sdma: remove duplicated sdma_load_context
spi: imx: fallback to PIO if dma setup failure
dmaengine: imx-sdma: add mcu_2_ecspi script
spi: imx: fix ERR009165
spi: imx: remove ERR009165 workaround on i.mx6ul
spi: imx: add new i.mx6ul compatible name in binding doc
dmaengine: imx-sdma: remove ERR009165 on i.mx6ul
dma: imx-sdma: add i.mx6ul compatible name
dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm
dmaengine: imx-sdma: add uart rom script
.../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 +
arch/arm/boot/dts/imx6q.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl.dtsi | 8 +-
drivers/dma/imx-sdma.c | 67 ++++++++++------
drivers/spi/spi-imx.c | 92 +++++++++++++++++++---
include/linux/platform_data/dma-imx-sdma.h | 8 +-
7 files changed, 135 insertions(+), 44 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523124758.28604-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523122909.25247-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523125704.30300-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fallback to PIO in case dma setup failed. For example, sdma firmware not
updated but ERR009165 workaroud added in kernel.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523133859.5625-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally spi_write_then_read() used a fixed statically allocated
buffer which limited the maximum message size it could handle. This
restriction was removed a while ago so that we could dynamically
allocate a buffer if required but the kerneldoc was not updated to
reflect this, do so.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200525133120.57273-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The PXA2xx SPI driver releases a runtime PM ref in the probe error path
even though it hasn't acquired a ref earlier.
Apparently commit e2b714afee ("spi: pxa2xx: Disable runtime PM if
controller registration fails") sought to copy-paste the invocation of
pm_runtime_disable() from pxa2xx_spi_remove(), but erroneously copied
the call to pm_runtime_put_noidle() as well. Drop it.
Fixes: e2b714afee ("spi: pxa2xx: Disable runtime PM if controller registration fails")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/58b2ac6942ca1f91aaeeafe512144bc5343e1d84.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The PXA2xx SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
pxa2xx_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: pxa2xx_spi_remove() disables the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in pxa2xx_spi_remove(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
The improper use of devm_spi_register_controller() was introduced in 2013
by commit a807fcd090 ("spi: pxa2xx: use devm_spi_register_master()"),
but all earlier versions of the driver going back to 2006 were likewise
broken because they invoked spi_unregister_master() at the end of
pxa2xx_spi_remove(), rather than at the beginning.
Fixes: e0c9905e87 ("[PATCH] SPI: add PXA2xx SSP SPI Driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.17+
Cc: Tsuchiya Yuto <kitakar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206403#c1
Link: https://lore.kernel.org/r/834c446b1cf3284d2660f1bee1ebe3e737cd02a9.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The Designware SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
dw_spi_remove_host() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: dw_spi_remove_host() shuts down the chip,
rendering the SPI bus inaccessible even though the SPI controller is
still registered. When the SPI controller is subsequently unregistered,
it unbinds all its slave devices. Because their drivers cannot access
the SPI bus, e.g. to quiesce interrupts, the slave devices may be left
in an improper state.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed after
unregistering the controller and specifically after unbinding of slaves.
Fix by reverting to the non-devm variant of spi_register_controller().
An alternative approach would be to use device-managed functions for all
steps in dw_spi_remove_host(), e.g. by calling devm_add_action_or_reset()
on probe. However that approach would add more LoC to the driver and
it wouldn't lend itself as well to backporting to stable.
Fixes: 04f421e7b0 ("spi: dw: use managed resources")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v3.14+
Cc: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/3fff8cb8ae44a9893840d0688be15bb88c090a14.1590408496.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
since chip spi driver need get the transfer direction by 'tx_buf' and
'rx_buf' of 'struct spi_transfer' in 'SPI_3WIRE' mode.
so, we need bypass 'SPI_CONTROLLER_MUST_RX' and 'SPI_CONTROLLER_MUST_TX'
feature in 'SPI_3WIRE' mode
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Link: https://lore.kernel.org/r/1590378348-8115-9-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
in l3gd20 driver startup, there is a setup failed error return from
stm32 spi driver
"
[ 2.687630] st-gyro-spi spi0.0: supply vdd not found, using dummy
regulator
[ 2.696869] st-gyro-spi spi0.0: supply vddio not found, using dummy
regulator
[ 2.706707] spi_stm32 40015000.spi: SPI transfer setup failed
[ 2.713741] st-gyro-spi spi0.0: SPI transfer failed: -22
[ 2.721096] spi_master spi0: failed to transfer one message from queue
[ 2.729268] iio iio:device0: failed to read Who-Am-I register.
[ 2.737504] st-gyro-spi: probe of spi0.0 failed with error -22
"
after debug into spi-stm32 driver, st-gyro-spi split two steps to read
l3gd20 id
first: send command to l3gd20 with read id command in tx_buf, rx_buf
is null.
second: read id with tx_buf is null, rx_buf not null.
so, for second step, stm32 driver recongise this process as 'SPI_SIMPLE_RX'
from stm32_spi_communication_type(), but there is no related process for this
type in stm32f4_spi_set_mode(), then we get error from
stm32_spi_transfer_one_setup().
we can use two method to fix this bug.
1, use stm32 spi's "In unidirectional receive-only mode (BIDIMODE=0 and
RXONLY=1)". but as our code running in sdram, the read latency is too large
to get so many receive overrun error in interrupts handler.
2, use stm32 spi's "In full-duplex (BIDIMODE=0 and RXONLY=0)", as tx_buf is
null, so add flag 'SPI_MASTER_MUST_TX' to spi master.
Change since V4:
1 remove dummy data sent out by stm32 spi driver
2 add flag 'SPI_MASTER_MUST_TX' to spi master
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Link: https://lore.kernel.org/r/1590378348-8115-8-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not valid to cache/short out selection of the mux.
mux_control_select() only locks the mux until mux_control_deselect()
is called. mux_control_deselect() may put the mux in some low power
state or some other user of the mux might select it for other purposes.
These things are probably not happening in the original setting where
this driver was developed, but it is said to be a generic SPI mux.
Also, the mux framework will short out the actual low level muxing
operation when/if that is possible.
Fixes: e9e40543ad ("spi: Add generic SPI multiplexer")
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200525104352.26807-1-peda@axentia.se
Signed-off-by: Mark Brown <broonie@kernel.org>
If the delay used is long enough the spi_delay_exec() will use a sleeping
function to implement it. Add a might_sleep() here to help avoid callers
using this from an atomic context and running into problems at runtime on
other systems.
Suggested-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200522155005.46099-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Add Tx/Rx finish wait methods to the MID DMA
spi: dw: Enable interrupts in accordance with DMA xfer mode
spi: dw: Discard static DW DMA slave structures
spi: dw: Discard unused void priv pointer
spi: dw: Discard dma_width member of the dw_spi structure
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 ---
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++++++
.../devicetree/bindings/spi/spi-dw.txt | 24 --
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 88 ++----
drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} | 261 ++++++++++--------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +++-
drivers/spi/spi-dw.h | 33 ++-
10 files changed, 392 insertions(+), 259 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
rename drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} (55%)
--
2.25.1
This patch fixes a null pointer bug in the spi driver spi-rb4xx.c by
moving the private data initialization to earlier in probe
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Link: https://lore.kernel.org/r/20200521183631.37806-1-ch6574@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This member has exactly the same value as n_bytes of the DW SPI private
data object, it's calculated at the same point of the transfer method,
n_bytes isn't changed during the whole transfer, and they even serve for
the same purpose - keep number of bytes per transfer word, though the
dma_width is used only to calculate the DMA source/destination addresses
width, which n_bytes could be also utilized for. Taking all of these
into account let's replace the dma_width member usage with n_bytes one
and remove the former.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing the "void *priv" member of the dw_spi data structure is unused
let's remove it. The glue-layers can embed the DW APB SSI controller
descriptor into their private data object. MMIO driver for instance
already utilizes that design pattern.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Having them declared is redundant since each struct dw_dma_chan has
the same structure embedded and the structure from the passed dma_chan
private pointer will be copied there as a result of the next calls
chain:
dma_request_channel() -> find_candidate() -> dma_chan_get() ->
device_alloc_chan_resources() = dwc_alloc_chan_resources() ->
dw_dma_filter().
So just remove the static dw_dma_chan structures and use a locally
declared data instance with dst_id/src_id set to the same values as
the static copies used to have.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
It's pointless to track the Tx overrun interrupts if Rx-only SPI
transfer is issued. Similarly there is no need in handling the Rx
overrun/underrun interrupts if Tx-only SPI transfer is executed.
So lets unmask the interrupts only if corresponding SPI
transactions are implied.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
On unbind of the BCM2835 SPI driver, the SPI controller is disabled
first and the DMA channels are terminated and torn down afterwards.
This seems backwards: In the theoretical case that DMA is active,
it might try to fill the SPI FIFOs even after the controller has
been disabled.
Reverse the order, thereby mirroring what's done on ->probe().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/ac79f1e3d6fd9a1f5e0cb4008c43b98ea70be3c2.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock. The SPI controller
is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_master(). Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835_spi_remove() tears down the DMA
channels and turns off the SPI controller, including its interrupts
and clock. The SPI controller is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_controller(). Note that
the struct spi_controller as well as the driver-private data are not
freed until after bcm2835_spi_remove() has finished, so accessing them
is safe.
Fixes: 247263dba2 ("spi: bcm2835: use devm_spi_register_master()")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When an SPI controller unregisters, it unbinds all its slave devices.
For this, their drivers may need to access the SPI bus, e.g. to quiesce
interrupts.
However since commit ffbbdd2132 ("spi: create a message queueing
infrastructure"), spi_destroy_queue() is executed before unbinding the
slaves. It sets ctlr->running = false, thereby preventing SPI bus
access and causing unbinding of slave devices to fail.
Fix by unbinding slaves before calling spi_destroy_queue().
Fixes: ffbbdd2132 ("spi: create a message queueing infrastructure")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.4+
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/8aaf9d44c153fe233b17bc2dec4eb679898d7e7b.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gareth Williams <gareth.williams.jx@renesas.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Serge Semin (19):
dt-bindings: spi: dw: Add Tx/Rx DMA properties
spi: dw: Add Tx/Rx finish wait methods to the MID DMA
spi: dw: Clear DMAC register when done or stopped
spi: dw: Fix native CS being unset
spi: dw: Enable interrupts in accordance with DMA xfer mode
spi: dw: Discard static DW DMA slave structures
spi: dw: Discard unused void priv pointer
spi: dw: Discard dma_width member of the dw_spi structure
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Initialize paddr in DW SPI MMIO private data
spi: dw: Fix Rx-only DMA transfers
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 42 ---
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++++++
.../devicetree/bindings/spi/spi-dw.txt | 24 --
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 7 +-
drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} | 257 ++++++++++--------
drivers/spi/spi-dw-mmio.c | 9 +-
drivers/spi/spi-dw-pci.c | 50 +++-
drivers/spi/spi-dw.c | 98 +++----
drivers/spi/spi-dw.h | 33 ++-
10 files changed, 405 insertions(+), 257 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} (53%)
--
2.25.1
The original implementation set num_chipselect to ROCKCHIP_SPI_MAX_CS_NUM (2)
which seems wrong here. spi0 has 2 native cs, all others just one. With
enable and use of cs_gpiods / GPIO CS, its correct to set the num_chipselect
from the num-cs property and set max_native_cs with the define.
If num-cs is missing the default set to num_chipselect = 1.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-4-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for spi slave mode in spi-rockchip. The register map has an entry
for it. If spi-slave is set in dts, set this corresponding bit and add to
mode_bits the SPI_NO_CS, allow slave mode without explicit CS use.
Slave abort function had been added.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup, move from the compatibily layer struct spi_master over
to struct spi_controller, and rename the related function calls.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
If DMAC register is left uncleared any further DMAless transfers
may cause the DMAC hardware handshaking interface getting activated.
So the next DMA-based Rx/Tx transaction will be started right
after the dma_async_issue_pending() method is invoked even if no
DMATDLR/DMARDLR conditions are met. This at the same time may cause
the Tx/Rx FIFO buffers underrun/overrun. In order to fix this we
must clear DMAC register after a current DMA-based transaction is
finished.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200515104758.6934-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is used only for the DW SPI DMA code initialization, that's
why there were no problems with it being uninitialized in Dw SPI MMIO
driver. Since in a further patch we are going to introduce the DW SPI DMA
support in the MMIO version of the driver, lets set the field with the
physical address of the DW SPI controller registers region.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200515104758.6934-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6e0a32d6f3 ("spi: dw: Fix default polarity of native
chipselect") attempted to fix the problem when GPIO active-high
chip-select is utilized to communicate with some SPI slave. It fixed
the problem, but broke the normal native CS support. At the same time
the reversion commit ada9e3fcc1 ("spi: dw: Correct handling of native
chipselect") didn't solve the problem either, since it just inverted
the set_cs() polarity perception without taking into account that
CS-high might be applicable. Here is what is done to finally fix the
problem.
DW SPI controller demands any native CS being set in order to proceed
with data transfer. So in order to activate the SPI communications we
must set any bit in the Slave Select DW SPI controller register no
matter whether the platform requests the GPIO- or native CS. Preferably
it should be the bit corresponding to the SPI slave CS number. But
currently the dw_spi_set_cs() method activates the chip-select
only if the second argument is false. Since the second argument of the
set_cs callback is expected to be a boolean with "is-high" semantics
(actual chip-select pin state value), the bit in the DW SPI Slave
Select register will be set only if SPI core requests the driver
to set the CS in the low state. So this will work for active-low
GPIO-based CS case, and won't work for active-high CS setting
the bit when SPI core actually needs to deactivate the CS.
This commit fixes the problem for all described cases. So no matter
whether an SPI slave needs GPIO- or native-based CS with active-high
or low signal the corresponding bit will be set in SER.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Fixes: ada9e3fcc1 ("spi: dw: Correct handling of native chipselect")
Fixes: 6e0a32d6f3 ("spi: dw: Fix default polarity of native chipselect")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200515104758.6934-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_get_and_ioremap_resource() to simplify code instead of
platform_get_resource() and devm_ioremap_resource(). This also gets
the resource that the following code uses.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1589185530-28170-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is superfluous in all cases where it's being used, i.e.
* ->can_dma() won't be called without dma_inited == 1
* DMA ->exit() callback can rely on txchan and rxchan variables
So, get rid of dma_inited flag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200507115449.8093-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA setup doesn't rely on certain type of DMA controller and thus
shouldn't use Intel Medfield settings, although it's harmless in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200507115449.8093-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Elkhart Lake PSE SPI is capable to utilize PSE DMA engine which is described
in ACPI. With help of acpi-dma module the support becomes a generic one.
Thus, add Elkhart Lake PSE DMA support and generic DMA hooks in SPI DesignWare
driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases, one of which is coming soon, we would like to have
a struct device pointer to request DMA channel. For this purpose
propagate it to ->dma_init() callback in DMA ops.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to prepare driver for the extension to support newer hardware,
add 'mfld' suffix to some related functions.
While here, move DMA parameters assignment under existing #ifdef
CONFIG_SPI_DW_MID_DMA.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no user of few headers without CONFIG_SPI_DW_MID_DMA being set.
Move them under condition.
While at it, remove unused slab.h there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
spi-dw-mid.c along with spi-dw.h are direct users of irqreturn.h
and nothing else is being used from interrupt.h. So, switch them
to use the former instead of latter one.
While here, move the header under #ifdef CONFIG_SPI_DW_MID_DMA
in spi-dw-mid.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling new IP support in the driver couple of variables
were left unused compiler is not happy about:
.../spi-dw.c: In function ‘dw_spi_update_cr0’:
.../spi-dw.c:264:17: warning: unused variable ‘dws’ [-Wunused-variable]
264 | struct dw_spi *dws = spi_controller_get_devdata(master);
| ^~~
.../spi-dw.c: In function ‘dw_spi_update_cr0_v1_01a’:
.../spi-dw.c:285:17: warning: unused variable ‘dws’ [-Wunused-variable]
285 | struct dw_spi *dws = spi_controller_get_devdata(master);
| ^~~
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DMA controller drivers do not tolerate non-zero values in
the DMA configuration structures. Zero them to avoid issues with
such DMA controller drivers. Even despite above this is a good
practice per se.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return negative error code -ENOMEM from the dma mapping error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200506125607.90952-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following coccicheck warning:
drivers/spi/spi-armada-3700.c:283:8-11: Unneeded variable: "ret". Return
"0" on line 315
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200506061911.19923-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Intel Keem Bay SPI controller, which uses DesignWare
DWC_ssi core. Bit 31 of CTRLR0 register is added for Keem Bay, to
configure the device as a master or as a slave serial peripheral.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-6-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds update_cr0() callback, in struct dw_spi.
Existing code that configure register CTRLR0 is moved into a new
function, dw_spi_update_cr0(), and this will be the default.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will fix typo in the register name used in the source code,
to be consistent with the register name used in the databook.
Databook: DW_apb_ssi_databook.pdf version 4.01a
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-2-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's an assortment of drive-by fixes for the new AMD SPI driver.
All of them are compile-tested only.
Lukas Wunner (5):
spi: amd: Fix duplicate iounmap in error path
spi: amd: Pass probe errors back to driver core
spi: amd: Drop duplicate driver data assignments
spi: amd: Fix refcount underflow on remove
spi: amd: Drop superfluous member from struct amd_spi
drivers/spi/spi-amd.c | 27 +++++----------------------
1 file changed, 5 insertions(+), 22 deletions(-)
--
2.26.2
The AMD SPI driver stores a pointer to the spi_master in struct amd_spi
so that it can get from the latter to the former in amd_spi_fifo_xfer().
It's simpler to just pass the pointer from the sole caller
amd_spi_master_transfer() and drop the pointer from struct amd_spi.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/a088b684ad292faf3bd036e51529e608e5c94638.1588590210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD SPI driver calls spi_master_put() in its ->remove() hook even
though the preceding call to spi_unregister_master() already drops a
ref, thus leading to a refcount underflow. Drop the superfluous call
to spi_master_put().
This only leaves the call to spi_unregister_master() in the ->remove()
hook, so it's safe to change the ->probe() hook to use the devm version
of spi_register_master() and drop the ->remove() hook altogether.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/5e53ccdf1eecd4e015dba99d0d77389107f8a2e3.1588590210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD SPI driver calls platform_set_drvdata() on probe even though
it's already been set by __spi_alloc_controller(). Likewise, it calls
platform_set_drvdata() on remove even though it's going to be set by
__device_release_driver(). Drop the duplicate assignments.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/499f8ad4759c2ff0f586e0459fb9a293faecff6d.1588590210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD SPI driver uses devm_ioremap_resource() to map its registers, so
they're automatically unmapped via device_release() when the last ref on
the SPI controller is dropped. The additional iounmap() in the ->probe()
error path is thus unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/497cc38ae2beb7900ae05a1463eb83ff96e2770e.1588590210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a warning at atmel_spi_next_xfer_dma_submit()
warning: context imbalance in atmel_spi_next_xfer_dma_submit()
- unexpected unlock
The root cause is the missing annotation
at atmel_spi_next_xfer_dma_submit()
Add the missing __must_hold(&as->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200429225723.31258-3-jbi.octave@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With a couple allies at Intel, and much badgering, I got confirmation
from Intel that at least BXT suffers from the same SPI chip-select
issue as Cannonlake (and beyond). The issue being that after going
through runtime suspend/resume, toggling the chip-select line without
also sending data does nothing.
Add the quirk to BXT to briefly toggle dynamic clock gating off and
on, forcing the fabric to wake up enough to notice the CS register
change.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: Shobhit Srivastava <shobhit.srivastava@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200427163238.1.Ib1faaabe236e37ea73be9b8dcc6aa034cb3c8804@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return negative error code -EPROBE_DEFER from the DMA probe defer
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200429075855.104487-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Luc Van Oostenryck