The commit 16ada730a7 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the current implementation DLL reset will be issued for
each ITAP and OTAP setting inside ATF, this is creating issues
in some scenarios and this sequence is not inline with the TRM.
To fix the issue, DLL reset should be removed from the ATF and
host driver will request it explicitly.
This patch update host driver to explicitly request for DLL reset
before ITAP (assert DLL) and after OTAP (release DLL) settings.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mask the ITAP and OTAP delay bits before updating with the new
tap value for Versal platform.
Fixes: 1a470721c8 ("sdhci: arasan: Add support for Versal Tap Delays")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow configuring the Output and Input tap values with zero to avoid
failures in some cases (one of them is SD boot mode) where the output
and input tap values may be already set to non-zero.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-8-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial code that was adding delays was doing a cast over undefined
memory. This meant that the delays would be all gibberish.
This change, allocates all delays on the stack, and assigns them from the
ZynqMP & Versal macros/phase-list. And then finally copies them over the
common iclk_phase & oclk_phase variables.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1594753953-62980-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kerneldoc expects arg descriptions to be in the format '@.*: '. If either
the '@' or the ':' is omitted then kerneldoc complains that the description
is missing. Add the missing ':' here and provide a new description for
'value'.
Fixes the following kernel build W=1 warnings:
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'host' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'value' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-msm.c:1887:6: warning: no previous prototype for ‘sdhci_msm_dump_vendor_regs’ [-Wmissing-prototypes]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Xiaobo Xie <X.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Soeren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-12-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These functions do not check the return value of devm_clk_register():
- sdhci_arasan_register_sdcardclk()
- sdhci_arasan_register_sampleclk()
Therefore, add the missed checks to fix them.
Fixes: c390f2110a ("mmc: sdhci-of-arasan: Add ability to export card clock")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200608162226.3259186-1-hslester96@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
Intel Keem Bay SoC eMMC/SD/SDIO controller is based on
Arasan SD 3.0 / eMMC 5.1 host controller IP.
However, it does not support 64-bit access as its AXI interface
has 32-bit address ports.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200526062758.17642-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI clock operations are platform specific. So it better to define
them separately for particular platform. This will prevent multiple
if..else conditions and will make it easy for user to add their own
clock operations handlers.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing driver code has the platform specific structures scattered
throughout the driver code. Rearrange the platform specific data
structures for more modularity and readability. This will help in adding
new static functions with more ease.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is 'struct sdhci_arasan_data' but also
'struct sdhci_arasan_of_data sdhci_arasan_data'. Rename the latter to
avoid confusion with the name of the struct.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to set tap delays for Xilinx Versal SD controller. The tap
delay registers have moved to SD controller space in Versal. Make the
changes accordingly.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586195015-128992-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core provides a helper function with the same functionality as
this controller's set_power() callback. Use it instead.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200306174413.20634-3-nsaenzjulienne@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes quirk which indicates a broken base clock. This was
making the kernel report wrong base clock of ~187MHz instead of 200MHz
even as the measurement on the hardware was showing 200MHz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579602095-30060-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DLL resets are required while executing the auto tuning procedure in
ZynqMP. This patch adds code to support the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579602095-30060-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Apart from taps set by auto tuning, ZynqMP platform has feature to set
the tap values manually. Add support to set tap delay values in HW via
ZynqMP SoC framework.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to read Clock Phase Delays from the DT and set it via
clk_set_phase() API from clock framework. Some of the controllers might
have their own handling of setting clock delays, for this keep the
set_clk_delays as function pointer which can be assigned controller
specific handling of the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are some operations like setting the clock delays may need to have
two clocks, one for output path and one for input path. Adding input
path clock for some phys to use.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To improve the code readability, use two different structs, one for
clock provider data and one for mmc platform data.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
SDXC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
eMMC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Muruganx <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct commands (DCMDs) are an optional feature of eMMC 5.1's command
queue engine (CQE). The Arasan eMMC 5.1 controller uses the CQHCI,
which exposes a control register bit to enable the feature.
The current implementation sets this bit unconditionally.
This patch allows to suppress the feature activation,
by specifying the property disable-cqe-dcmd.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 84362d79f4 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host controllers on TI's AM654 SOCs are not compatible with
the phy and consumer model of the sdhci-of-arasan driver. It turns out
that for optimal operation at higher speeds, a special tuning procedure
needs to be implemented which involves configuration of platform
specific phy registers.
Therefore, branch out to a new sdhci_am654 driver and add the phy
register space with all phy configurations to it. Populate AM654
specific callbacks to sdhci_ops and add SDHCI_QUIRKS wherever
applicable.
Only add support for upto High Speed for SD card and upto DDR52 speed
mode for eMMC. Higher speeds will be added in subsequent patches.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on TI's AM654 devices.
Therefore, add a new compatible, AM654 specific quirks
and a new AM654 specific set_clock function which
configures the PHY in a sane way.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the driver passes platform data as a global structure
and uses the .data of of_device_id to pass the soc_ctl_map. To
make the implementation more flexible add a single data structure
that incorporates both of the above and pass it in the .data of
of_device_id.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers immediately report SDHCI_CLOCK_INT_STABLE after
enabling the clock even when the clock is not stable. When used in
conjunction with older/slower cards, this can result in:
mmc0: error -84 whilst initialising SD card
When the stable reporting is known to be broken, we simply wait for the
maximum stabilization period.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On SD 2.00 cards we get lots of these messages:
"mmc0: Got data interrupt 0x00000002 even though no data operation was in progress"
By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen.
A single card claiming to be SD 3.00 compliant also generates the interrupts,
but since the card's manfacturing date is 2002 mar, it's unlikely to really be
SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4).
This has been reported on Xilinx devices that also use the Arasan IP.
See https://patchwork.kernel.org/patch/8062871/
This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The
Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and
does not support DDR modes.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CQHCI initialization and implement CQHCI operations for Arasan
SDHCI variant host, namely arasan,sdhci-5.1, which is used by Rockchip
RK3399 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power register needs to have a valid voltage set
even when the power supply is managed by an external regulator.
Signed-off-by: Milan Stevanovic <milan.o.stevanovic@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This increases consistency of the code across the sdhci family.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ret is signed however is printed as unsigned fix the same.
If printed as a negative number the result is easier to read.
No functional change.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the get_timeout_clock callback doesn't clearly
have a statement that it needs the variant drivers to return
the timeout clock rate in kHz if the SDHCI_TIMEOUT_CLK_UNIT
isn't present, otherwise the variant drivers should return it
in MHz. It's also very likely that further variant drivers which
are going to use this callback will be confused by this situation.
Given the fact that moderm sdhci variant hosts are very prone to get
the timeout clock from common clock framework (actually the only three
users did that), it's more natural to return the value in Hz and we
make an explicit comment there. Then we put the unit conversion inside
the sdhci core. Thus will improve the code and prevent further misuses.
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11 ("mmc: arasan: Add driver for Arasan SDHCI")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:
[ 93.405085] mmc1: unexpected status 0x800900 after switch
[ 93.408474] mmc1: switch to bus width 1 failed
[ 93.408482] mmc1: mmc_select_hs200 failed, error -110
[ 93.408492] mmc1: error -110 during resume (card was removed?)
[ 93.408705] PM: resume of devices complete after 213.453 msecs
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci-of-arasan.c:253:6: warning:
symbol 'sdhci_arasan_reset' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.
When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
corecfg_clockmultiplier indicates clock multiplier value of
programmable clock generator which should be the same value
of SDHCI_CAPABILITIES_1. The default value of the register,
corecfg_clockmultiplier, is 0x10. But actually it is a mistake
by designer as our intention was to set it to be zero which
means we don't support programmable clock generator. So we have
to make it to be zero on bootloader which seems work fine until
now. But now we find an issue that when deploying genpd support
for it, the remove callback will trigger the genpd to poweroff the
power domain for sdhci-of-arasan which manage the controller, phy
and corecfg_* stuff.
So when we do bind/unbind the driver, we have already reinit
the controller and phy, but without doing that for corecfg_*.
Regarding to only the corecfg_clockmultipler is wrong, let's
fix it by explicitly marking it to be zero when probing. With
this change, we could do bind/unbind successfully.
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Tested-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Gustavo A. R. Silva