Add dev_wakeup_path() helper to avoid to spread
dev->power.wakeup_path test in drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DMA usage is optional for the I2C driver. check for the -ENODEV
error in order to avoid displaying an error when no DMA
has been requested.
Cleaning up the error messages during probe, remove the additional
-EPROBE_DEFER within probe function since additional error message
doesn't give much more information than what is already reported
within the stm32_i2c_dma_request function.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rely on the core functions to implement the host-notify
protocol via the a I2C slave device.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We want to break with "i" set to zero whether we find the rate we want
or not. In the current code, if we don't find the rate we want then it
exits the loop with "i" set to -1 and results in an array underflow.
Fixes: 09cc9a3bce ("i2c: stm32f7: allows for any bus frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not limitate to the 3 (100KHz, 400KHz, 1MHz) bus frequency but
instead allows any frequency (if it matches timing requirements).
Depending on the requested frequency, use the spec data from either
Standard, Fast or Fast Plus mode.
Hardcoding of min/max bus frequencies is removed and is instead computed.
The driver do not use anymore speed identifier but instead handle
directly the frequency and figure out the spec data (necessary
for the computation of the timing register) based on the frequency.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not print an error trace when deferring probe for some resource.
Fix as well the error message in case of tx dma_request_chan failure.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions: i2c_parse_fw_timings().
While here, replace hard coded values with standard bus frequency definitions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PECR register provides received packet computed PEC value.
It makes no sense restoring its value after a reset, and anyway,
as read-only register it cannot be restored.
Fixes: ea6dd25dee ("i2c: stm32f7: add PM_SLEEP suspend/resume support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a new stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Defer the initial enabling of the Fast Mode Plus bits after the
stm32f7_i2c_setup_timing call in probe function in order to avoid
enabling them if speed is downgraded.
Clear & restore the Fast Mode Plus bits in the suspend/resume
handlers of the driver.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow the i2c-stm32f7 controller to become a wakeup-source
of the system. In such case, when a slave is registered to the
I2C controller, receiving a I2C message targeting that registered
slave address wakes up the suspended system.
In order to be able to wake-up, the I2C controller DT node
must have the property wakeup-source defined and a slave
must be registered.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Backup/restore I2C registers as part of the suspend/resume
handlers. The device is marked as suspended to ensure that
transfers are rejected during the suspended period.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
Fix a typo in the free slave id search loop. Instead of I2C_CLIENT_PEC,
it should have been I2C_CLIENT_TEN. The slave id 1 can only handle 7-bit
addresses and thus is not eligible in case of 10-bit addresses.
As a matter of fact none of the slave id support I2C_CLIENT_PEC, overall
check is performed at the beginning of the stm32f7_i2c_reg_slave function.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Distinguish between the case where dma information is not provided
within the DT and the case of an error during the dma init.
Exit the probe with error in case of an error during dma init.
Fixes: bb8822cbbc ("i2c: i2c-stm32: Add generic DMA API")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing dma channels free calls in case of error during probe
and reorder the remove function so that dma channels are freed after
the i2c adapter is deleted.
Overall, reorder the remove function so that probe error handling order
and remove function order are same.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IP can handle two slave addresses. One address can either be
7 bits or 10 bits while the other can only be 7 bits.
In order to ensure that a 10 bits address can always be allocated
(assuming there is only one 7 bits address already allocated),
pick up the 7-bits only address slot in priority when performing a 7-bits
address allocation.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the following warning:
drivers/i2c/busses/i2c-stm32f7.c:315:
warning: cannot understand function prototype:
'struct stm32f7_i2c_spec i2c_specs[] =
Replace a comment starting with /** by simply /* to avoid having
it interpreted as a kernel-doc comment.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
remains set until next master xfer (e.g. when STOPIE irq get unmasked).
In this case, completion is generated too early: immediately upon new
transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
stretches the SCL line: the bus gets busy until a future master transfer
triggers the bus busy / recovery mechanism (this can take time... and
may never happen at all)
So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.
[1] https://www.kernel.org/doc/Documentation/i2c/slave-interface
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Static structure stm32f7_i2c_algo, of type i2c_algorithm, is used only
when it is assigned to constant field algo of a variable having type
i2c_adapter. As stm32f7_i2c_algo is therefore never modified, make it
const as well to protect it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the support of I2C_SMBUS_I2C_BLOCK_DATA transaction type
for the stm32f7 SMBUS Controller.
Use emulated I2C_SMBUS_I2C_BLOCK_DATA transactions as there is no specific
hardware in STM32 I2C to manage this (e.g. like no need for PEC here).
Emulated transfer will fall back calling i2c transfer method where there's
already support for DMAs for example.
So, use the I2C_FUNC_SMBUS_I2C_BLOCK in stm32f7_i2c_func(), and rely on
emulated transfer by returning -EOPNOTSUPP in the smbus_xfer() routine
for such a case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During probe, return the "get_irq" error value instead of -EINVAL which
allows the driver to be deferred probed if needed.
Fix also the case where of_irq_get() returns a negative value.
Note :
On failure of_irq_get() returns 0 or a negative value while
platform_get_irq() returns a negative value.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use PM Runtime API to enable/disable clock
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some data structure members were either misspelled or missing.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Fixes: 380b8a85e7 ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds slave support for I2C controller embedded in STM32F7 SoC
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for 10-bit device address for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drive setup structure is not properly allocated.
Make it static instead of pointer to store driver data.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patrice Chotard