Some systems need current frequency from last_status for calculation
but it is zeroed during initialization. When the device starts there is
no history, but we can assume that the last frequency was the
same as the initial frequency (which is also used in 'previous_freq').
The log shows the result of this misinterpreted value.
[ 2.042847] ... Failed to get voltage for frequency 0: -34
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Smatch complains because platform_get_resource() returns NULL on error
and not an error pointer so the check is wrong. Julia Lawall pointed
out that normally we don't check these, because devm_ioremap_resource()
has a check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
When device_register() returns with error, it has already
done put_device() on the input device pointer.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
devm_kzalloc of devfreq's statistics data structure has been
using its parent device as the dev allocated for.
If a device's devfreq is disabled in run-time,
such allocated memory won't be freed.
Desginating more precisely with the devfreq device
pointer fixes the issue.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch use the phandle to find the instance of devfreq-event device in
Device Tree when calling the devfreq_event_get_edev_by_phandle() because there
is two type devfreq-event devices as following:
First case, exynos-ppmu.c driver provides the maximum four event of each PPMU.
So, when getting the instance of devfreq-event device, using the unique name of
struct devfreq_event_desc.
Second case, exynos-nocp.c driver provide the only one event of each NoC Probe
device. So, when getting the instance of devfreq-event device, using the
phandle of each NoC probe device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds NoC (Network on Chip) Probe driver which provides
the primitive values to get the performance data. The packets that the Network
on Chip (NoC) probes detects are transported over the network infrastructure.
Exynos542x bus has multiple NoC probes to provide bandwidth information about
behavior of the SoC that you can use while analyzing system performance.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch removes the unused exynos4/5 busfreq driver. Instead,
generic exynos-bus frequency driver support the all Exynos SoCs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the support of bus frequency feature for sub-blocks which share
the one power line. If each bus depends on the power line, each bus is not able
to change the voltage by oneself. To optimize the power-consumption on runtime,
some buses using the same power line should change the source clock and
regulator at the same time. So, this patch uses the passive governor to support
the bus frequency for all buses which sharing the one power line.
For example,
Exynos3250 include the two power line for AXI buses as following:
: VDD_MIF : MIF (Memory Interface) provide the DMC (Dynamic Memory Controller)
with the power (regulator).
: VDD_INT : INT (Internal) provide the various sub-blocks with the power
(regulator).
Each bus is included in as follwoing block. In the case of VDD_MIF, only DMC bus
use the power line. So, there is no any depencency between buese. But, in the
case of VDD_INT, various buses share the one power line of VDD_INT. We need to
make the depenency between buses. When using passive governor, there is no
problem to support the bus frequency as DVFS for all buses. One bus should be
operated as the parent bus device which gathering the current load of INT block
and then decides the new frequency with some governors except of passive
governor. After deciding the new frequency by the parent bus device, the rest
bus devices will change the each source clock according to new frequency of the
parent bus device.
- MIF (Memory Interface) block
: VDD_MIF |--- DMC
- INT (Internal) block
: VDD_INT |--- LEFTBUS (parent)
|--- PERIL
|--- MFC
|--- G3D
|--- RIGHTBUS
|--- FSYS
|--- LCD0
|--- PERIR
|--- ISP
|--- CAM
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[tjakobi: Reported debugfs error during booting and cw00.choi fix it.]
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the new passive governor for DEVFREQ framework. The following
governors are already present and used for DVFS (Dynamic Voltage and Frequency
Scaling) drivers. The following governors are independently used for one device
driver which don't give the influence to other device drviers and also don't
receive the effect from other device drivers.
- ondemand / performance / powersave / userspace
The passive governor depends on operation of parent driver with specific
governos extremely and is not able to decide the new frequency by oneself.
According to the decided new frequency of parent driver with governor,
the passive governor uses it to decide the appropriate frequency for own
device driver. The passive governor must need the following information
from device tree:
- the source clock and OPP tables
- the instance of parent device
For exameple,
there are one more devfreq device drivers which need to change their source
clock according to their utilization on runtime. But, they share the same
power line (e.g., regulator). So, specific device driver is operated as parent
with ondemand governor and then the rest device driver with passive governor
is influenced by parent device.
Suggested-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[tjakobi: Reported RCU locking issue and cw00.choi fix it]
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
[linux.amoon: Reported possible recursive locking and cw00.choi fix it]
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the new DEVFREQ_TRANSITION_NOTIFIER notifier to send
the notification when the frequency of device is changed.
This notifier has two state as following:
- DEVFREQ_PRECHANGE : Notify it before chaning the frequency of device
- DEVFREQ_POSTCHANGE : Notify it after changed the frequency of device
And this patch adds the resourced-managed function to release the resource
automatically when error happen.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the new devfreq_get_devfreq_by_phandle() OF helper function
which can find the instance of devfreq device by using phandle ("devfreq").
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the generic exynos bus frequency driver for AMBA AXI bus
of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
have the common architecture for bus between DRAM and sub-blocks in SoC.
This driver can support the generic bus frequency driver for Exynos SoCs.
In devicetree, Each bus block has a bus clock, regulator, operation-point
and devfreq-event devices which measure the utilization of each bus block.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
As per the documentation of the devfreq_dev_profile.target callback, set
the freq argument to the new frequency before returning.
This caused endless messages like this after recent changes in the core:
devfreq 6000c800.actmon: Couldn't update frequency transition information.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Before this patch for a device without statistics support,
$ cat trans_stat
From : To
: time(ms)
Total transitions : 0
$
After this patch applied for such a device,
$ cat trans_stat
Not Supported.
$
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch initialize the freq_table array of each devfreq device by using
the devfreq_set_freq_table(). If freq_table is NULL, the devfreq framework
is not able to support the frequency transtion information through sysfs.
The OPP core uses the integer type for the number of opps in the opp list
and uses the 'unsigned long' type for each frequency. So, this patch
modifies the type of some variable as following:
- the type of freq_table : unsigned int -> unsigned long
- the type of max_state : unsigned int -> int
- Corrected types, format strings, mutex usages by MyungJoo
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds the 'show_one' macro to simplify the duplicate code
of both max_freq_show() and min_freq_show().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch just fixes following error and warning by using
scripts/checkpatch.pl.
- Follwoing issue from checkpatch.pl:
ERROR: space prohibited before that close parenthesis ')'
+ if (count < 0 ) {
WARNING: line over 80 characters
+ ptr = devres_alloc(devm_devfreq_event_release, sizeof(*ptr), GFP_KERNEL);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch just removes the error log when
devfreq_event_get_edev_by_phandle() fail to get the instance of
devfreq-event device. It is related to sequence of the probe() of each
driver. So, this error log might show the always during kernel booting.
Each driver using this function can show the appropriate error log.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
When device_register() fails, kfree(devfreq) is called already in
devfreq_dev_release(), hence there is no need to call kfree(devfreq)
in err_dev again.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Writing the currently set governor into sysfs currently
seems to fail.
Fix this by setting the return code to zero before
leaving governor_store().
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
time_in_state in struct devfreq is defined as unsigned long, so
devm_kzalloc should use sizeof(unsigned long) as argument instead
of sizeof(unsigned int), otherwise it will cause unexpected result
in 64bit system.
Signed-off-by: Xiaolong Ye <yexl@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The thermal infrastructure should use the devfreq cooling device, which
uses the OPP library to disable OPPs as necessary.
Fix a couple of typos in the same comment while we are at it.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The return value of get_dev_status() can be reused. Cache it so that
other parts of the kernel can reuse it instead of having to call the
same function again.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds the support for PPMU (Platform Performance Monitoring Unit)
version 2.0 for Exynos5433 SoC. Exynos5433 SoC must need PPMUv2 which is
quite different from PPMUv1.1. The exynos-ppmu.c driver supports both PPMUv1.1
and PPMUv2.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
To avoid a race in which the interrupt will be handled before the
drvdata has been set up.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
As the DT bindings don't have an operating-points property any more,
build the OPP table from the frequencies supported by the EMC clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Now that we have per-user clocks and the possibility to set constraints
in a clock, set a floor constraint on the EMC clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There seemed to be some miscommunication and an old version of the
submitted patches was merged.
This commit updates the driver to v5, which had this changelog:
* Clarify the units of avg_dependency_threshold
* Remove unused references to platform_device
* Enable and disable interrupts on governor events
* Make sure we handle all interrupts for any of the devices we are sampling
* Move locking to be per-actmon-device
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
CC: Alex Frid <afrid@nvidia.com>
CC: Mikko Perttunen <mikko.perttunen@kapsi.fi>
[Added const to device ID by MyungJoo]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
_remove_devfreq() does not have @skip anymore after 3.16.
The comment for _remove_devfreq() has been updated correspondingly.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds the const keyword for devfreq_event_ops structure
because the ops of devfreq_event_desc structure should not be changed
after initialization.
Cc: Myungjoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is a typo here so we test "edev" but we intended to test
"edev[i]".
Fixes: f262f28c14 ('PM / devfreq: event: Add devfreq_event class')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
This patch fixes the build break of the exynos-ppmu driver because Makefile
in drivers/devfreq don't include the entry of devfreq-event.c driver.
The original patch[1] includes the entry to build devfreq-event.c without
the build break. This build break is generated in the process of merging the
patch.
[1] https://lkml.org/lkml/2015/1/25/579
- [PATCH v10 1/7] devfreq: event: Add new devfreq_event class to provide basic
data for devfreq governor
CC init/version.o
LD init/built-in.o
drivers/built-in.o: In function `exynos_ppmu_probe':
binder.c:(.text+0x4447ec): undefined reference to `devm_devfreq_event_add_edev'
make: *** [vmlinux] Error 1
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds a new class in devfreq, devfreq_event, which provides
raw data (e.g., memory bus utilization, GPU utilization) for devfreq
governors.
- devfreq_event device : Provides raw data for a governor of a devfreq device
- devfreq device : Monitors device state and changes frequency/voltage
of the device using the raw data from its
devfreq_event device.
A devfreq device dertermines performance states (normally the frequency
and the voltage vlues) based on the results its designtated devfreq governor:
e.g., ondemand, performance, powersave.
In order to give such results required by a devfreq device, the devfreq
governor requires data that indicates the performance requirement given
to the devfreq device. The conventional (previous) implementatino of
devfreq subsystem requires a devfreq device driver to implement its own
mechanism to acquire performance requirement for its governor. However,
there had been issues with such requirements:
1. Although performance requirement of such devices is usually acquired
from common devices (PMU/PPMU), we do not have any abstract structure to
represent them properly.
2. Such performance requirement devices (PMU/PPMU) are actual hardware
pieces that may be represented by Device Tree directly while devfreq device
itself is a virtual entity that are not considered to be represented by
Device Tree according to Device Tree folks.
In order to address such issues, a devferq_event device (represented by
this patch) provides a template for device drivers representing
performance monitoring unit, which gives the basic or raw data for
preformance requirement, which in turn, is required by devfreq governors.
The following description explains the feature of two kind of devfreq class:
- devfreq class (existing)
: devfreq consumer device use raw data from devfreq_event device for
determining proper current system state and change voltage/frequency
dynamically using various governors.
- devfreq_event class (new)
: Provide measured raw data to devfreq device for governor
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Commit message rewritten & conflict resolved by MyungJoo]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The ACTMON block can monitor several counters, providing averaging and firing
interrupts based on watermarking configuration. This implementation monitors
the MCALL and MCCPU counters to choose an appropriate frequency for the
external memory clock.
This patch is based on work by Alex Frid <afrid@nvidia.com> and Mikko
Perttunen <mikko.perttunen@kapsi.fi>.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
Export symbols from the PPMU driver needed to build the exynos bus
driver as a module.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
These functions are indended for use by drivers and should be available
also when the driver is built as a module.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ãrjan Eide <orjan.eide@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The Kconfig symbol ARCH_HAS_OPP became redundant in v3.16: commit
049d595a4d ("PM / OPP: Make OPP invisible to users in Kconfig")
removed the only dependency that used it. Setting it had no effect
anymore.
So commit 78c5e0bb14 ("PM / OPP: Remove ARCH_HAS_OPP") removed it. For
some reason that commit did not remove all select statements for that
symbol. These statements are now useless. Remove one from devfreq too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Checks for CONFIG_EXYNOS_ASV were added in v3.3. But the related Kconfig
symbol has never been added to the tree. Remove these checks, as they
always evaluate to false.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[Merge conflict resolved by MyungJoo]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch uses devm_devfreq_add_device()/devm_devfreq_register_opp_notifier()
to control automatically the resource of devfreq.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add resource-managed function for devfreq opp as following
functions. The devm_devfreq_register_opp_notifier() manages automatically
the registration of devfreq opp using device resource management.
- devm_devfreq_register_opp_notifier
- devm_devfreq_unregister_opp_notifier()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add resource-managed function for devfreq device as following
functions. The devm_devfreq_add_device() manages automatically the memory
of devfreq device using device resource management.
- devm_devfreq_add_device()
- devm_devfreq_remove_device()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch modify devfreq_remove_device() to improve the sequence of resource
free. If executing existing devfreq_remove_device(), this function always
executes _remove_devfreq() twice. In result, second _remove_devfreq() always
return error value. So, This patch resolves complicated function sequence
as following:
[Flow sequence before modification]
devfreq_remove_device()
_remove_devfreq(devfreq, false)
kfree(devfreq); /* Free devfreq */
if (!skip ...) { /* skip is false */
device_unregister(&devfreq->dev)
put_device(&devfreq->dev);
...
dev->release()
devfreq_dev_release()
_remove_devfreq(devfreq, true) <- Recall to free devfreq
/*
* Always return error without freeing resource because
* already _remove_devfreq() frees the memory of devfreq.
*/
}
[Flow sequence after modification]
devfreq_remove_device
device_unregister(&devfreq->dev)
put_device(&devfreq->dev);
..
dev->release()
devfreq_dev_release()
_remove_devfreq()
kfree(devfreq); /* Free devfreq */
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Merge conflict resolved by MyungJoo]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Move common PPMU code from exynos[45]_bus.c to exynos_ppmu.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This is a preparation for making more PPMU code common for
EXYNOS devfreq drivers.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This is a preparation for making more PPMU code common for
EXYNOS devfreq drivers.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch converts exynos4_bus driver to use common PPMU code
(exynos_ppmu.c) instead of individual functions related to PPC
because PPMU is integrated module with both PPC and Bus event
generator. When using PPMU to get bus performance read/write
event exynos4_bus driver deson't need to consider memory type.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[bzolnier: splitted out changes from the bigger patch]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add CONFIG_PM_OPP dependecy to exynos5_bus driver
to fix probe fail. If CONFIG_PM_OPP is disabled, dev_pm_opp_find_freq_floor()
will always return ERR_PTR(-EINVAL) error.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch use SIMPLE_DEV_PM_OPS macro instead of legacy method.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add CONFIG_PM_OPP dependecy to exynos4_bus driver
to fix probe fail as following log:
[ 3.721389] exynos4-busfreq busfreq.3: Fail to add opp entries.
[ 3.721697] exynos4-busfreq: probe of busfreq.3 failed with error -22
If CONFIG_PM_OPP is disabled, dev_pm_opp_find_freq_floor() in xxx_probe()
will always return -EINVAL error.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch use SIMPLE_DEV_PM_OPS macro instead of legacy method.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch fix bug about resource leak when happening probe fail and code clean
to add debug message.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The current devfreq_update_status() has the following bugs:
- If previous frequency doesn't have a valid level, it does an out of bounds
access into the trans_table and causes memory corruption.
- When the new frequency doesn't have a valid level, the time spent in the
new frequency is counted towards the next valid frequency switch instead of
being ignored.
- The time spent on the previous frequency is added to the new frequency's
stats instead of the previous frequency's stats.
This patch fixes all of this.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Exynos4 devfreq driver uses mach/map.h which is not available on
multiplatform. Hence disable build on multiplatform for now.
Without this patch we get the following build errors:
drivers/devfreq/exynos/exynos4_bus.h:15:22: fatal error: mach/map.h: No such file or directory
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes follwoing warning:
In file included from drivers/devfreq/exynos/exynos4_bus.h:15:0,
from drivers/devfreq/exynos/exynos4_bus.c:35:
arch/arm/mach-exynos/include/mach/map.h:22:0: warning: "S3C_UART_OFFSET" redefined [enabled by default]
In file included from drivers/devfreq/exynos/exynos4_bus.c:33:0:
arch/arm/plat-samsung/include/plat/map-s5p.h:57:0: note: this is the location of the previous definition
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We don't need to keep the definitions for exynos4_bus into
mach-exynos/ so this moves them into drviers/devfreq with
adding header file.
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The create_freezable_workqueue() function returns a NULL on error and
not an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
devm_* APIs are device managed and make clean up and exit codes
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
platform_device_register_simple does not return NULL.
Hence NULL check is not required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
* pm-cpufreq: (167 commits)
cpufreq: create per policy rwsem instead of per CPU cpu_policy_rwsem
intel_pstate: Add Baytrail support
intel_pstate: Refactor driver to support CPUs with different MSR layouts
cpufreq: Implement light weight ->target_index() routine
PM / OPP: rename header to linux/pm_opp.h
PM / OPP: rename data structures to dev_pm equivalents
PM / OPP: rename functions to dev_pm_opp*
cpufreq / governor: Remove fossil comment
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
...
Conflicts:
drivers/devfreq/exynos/exynos5_bus.c
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, code include opp.h twice. Remove one inclusion
of opp.h
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the devfreq_class code to use the
correct field.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dependencies on CPU_EXYNOS4212 and CPU_EXYNOS4412 for the "ARM
Exynos4210/4212/4412 Memory Bus DEVFREQ Driver" were added in commit
7b40503811 ("PM/Devfreq: Add Exynos4-bus
device DVFS driver for Exynos4210/4212/4412."). The tree (at that time,
v3.3, and currently) makes clear that this should have been dependencies
on SOC_EXYNOS4212 and SOC_EXYNOS4412.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Add the missing unlock before return from function
exynos4_busfreq_pm_notifier_event() in the error
handling case.
This issue introduced by commit 8fa938
(PM / devfreq: exynos4_bus: honor RCU lock usage)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Resolved path conflicts by MyungJoo Ham]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
devfreq stats is not taking device suspend and resume into
account. Fix it.
Signed-off-by: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Exynos5-bus device devfreq driver monitors PPMU counters and
adjusts operating frequencies and voltages with OPP. ASV should
be used to provide appropriate voltages as per the speed group
of the SoC rather than using a constant 1.025V.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
[myungjoo.ham@samsung.com: minor style update]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
In anticipation of the new exynos5 devfreq and ppmu driver, create
an exynos sub-directory. Move the existing exynos4 devfreq driver
into the same.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
OPP pointers cannot be expected to be valid beyond the boundary
of rcu_read_lock and rcu_read_unlock. Unfortunately, the current
exynos4 busfreq driver does not honor the usage constraint and stores
the OPP pointer in struct busfreq_data. This could potentially
become invalid later such as: across devfreq opp change decisions,
resulting in unpredictable behavior.
To fix this, we introduce a busfreq specific busfreq_opp_info
structure which is used to handle OPP information. OPP information
is de-referenced to voltage and frequency pairs as needed into
busfreq_opp_info structure and used as needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP pointers are protected by RCU locks, the pointer validity is
permissible only under the section of rcu_read_lock to rcu_read_unlock
Add documentation to the effect.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba