Drop the macros used to shift the flow-control settings to make the code
more readable for consistency with the other requests.
Signed-off-by: Johan Hovold <johan@kernel.org>
The vendor request used to set the flow-control settings also sets the
state of the modem-control lines.
Add state variables to keep track of the modem-control lines to avoid
always asserting the lines whenever the flow-control settings are
updated.
This specifically also avoids asserting DTR/RTS when opening a port with
the line speed set to B0.
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP210X_SET_MHS request cannot be used to control RTS when hardware
flow control (auto-RTS) is enabled and instead returns an error which is
currently logged as:
cp210x ttyUSB0: failed set request 0x7 status: -32
when opening and closing a port (and on TIOCMSET requests).
Add a crtscts flag to keep track of the hardware flow-control setting
and use it to suppress any request to change RTS when auto-RTS is
enabled.
Note that RTS is still deasserted when disabling the UART as part of
close.
Reported-by: Pho Tran <pho.tran@silabs.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This code should return -ENOMEM if the kmalloc() fails but instead
it returns success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix up B0 handling which should leave the baud rate unchanged and
specifically not report back a non-B0 rate when B0 is requested; must
temporarily disable hardware flow control so that RTS can be deasserted;
and should reassert DTR/RTS when moving from B0.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the modem pins are set up correctly when opening the
port to avoid leaving, for example, DTR and RTS configured as inputs,
which is the device default.
This is specifically needed to be able to control DTR and RTS when
hardware flow control is disabled.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix the gpio-mode handling so that all the pins are under driver control
(i.e. in gpio mode) when hardware flow control is disabled.
This is specifically needed to be able to control RTS.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Shift the line-setting values when defining them rather than in
set_termios() for consistency and improved readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to release the control interface at disconnect so that the
driver can be unbound without leaking resources (and later rebound).
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the probed device has an interface 0 to avoid
dereferencing a NULL pointer in case of a malicious device or during
USB-descriptor fuzzing.
Fixes: c2d405aa86 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
This should return -ENOMEM instead of 0 if the kmalloc() fails.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The Exar XR21V141X can be used in either ACM mode using the cdc-acm
driver or in "custom driver" mode in which further features such as
hardware and software flow control, GPIO control and in-band line-status
reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to the device if the custom USB-serial
driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20201122170822.21715-4-mani@kernel.org
[ johan: rewrite commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for MaxLinear/Exar USB to Serial converters. This driver
only supports XR21V141X series but it can be extended to other series
from Exar as well in future.
This driver is inspired from the initial one submitted by Patong Yang:
https://lore.kernel.org/r/20180404070634.nhspvmxcjwfgjkcv@advantechmxl-desktop
While the initial driver was a custom tty USB driver exposing whole
new serial interface ttyXRUSBn, this version is completely based on USB
serial core thus exposing the interfaces as ttyUSBn. This will avoid
the overhead of exposing a new USB serial interface which the userspace
tools are unaware of.
The Exar XR21V141X can be used in either ACM mode using the cdc-acm
driver or in "custom driver" mode in which further features such as
hardware and software flow control, GPIO control and in-band line-status
reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
corrently.
A follow-on patch will prevent cdc_acm from binding whenever this driver
is enabled.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20201122170822.21715-2-mani@kernel.org
[ johan: fix some style nits, group related functions, drop unused
callbacks, and amend commit message; a few remaining
non-trivial issues will be fixed separately ]
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity checks.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a copy-paste error in the ti_vread_sync() debug message.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity check.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop include directives that are no longer used.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to check for short control transfers when sending data
so remove the redundant sanity checks.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Update the XON/XOFF control characters also when no other flow-control
flag has changed and software flow control is enabled.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
At least CP2102 requires the XON/XOFF limits to be initialised in order
for software input flow control (IXOFF) to work. Specifically, XOFF is
never sent if the XOFF limit is left at its default value of zero.
Set the limits so that input is throttled when the FIFO free level drops
below 128 bytes and restarted when the FIFO fill level drops below 128
bytes.
Note that the threshold values have been chosen so that they can be used
also with CP2105 which has the smallest FIFO of the currently supported
device types (288 byte for the SCI port). If needed the limits can be
made device specific later.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When data is transmitted between two serial ports, the phenomenon of
data loss often occurs. The two kinds of flow control commonly used in
serial communication are hardware flow control and software flow
control.
In serial communication, If you only use RX/TX/GND Pins, you can't do
hardware flow. So we often used software flow control and prevent data
loss. The user sets the software flow control through the application
program, and the application program sets the software flow control mode
for the serial port chip through the driver.
For the cp210 serial port chip, its driver lacks the software flow
control setting code, so the user cannot set the software flow control
function through the application program. This adds the missing software
flow control.
Signed-off-by: Wang Sheng Long <shenglong.wang.ext@siemens.com>
Link: https://lore.kernel.org/r/20210104094502.3942-1-china_shenglong@163.com
[ johan: rework properly on top of recent termios changes ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The latest chip family (HXN) apparently does not support setting the
line speed using divisors and instead needs to use the direct encoding
scheme for all rates.
This specifically enables 50, 110, 134, 200 bps and other rates not
supported by the original chip type.
Fixes: ebd09f1cd4 ("USB: serial: pl2303: add support for PL2303HXN")
Cc: stable@vger.kernel.org # 5.5
Cc: Charles Yeh <charlesyeh522@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Generate a change uevent when the "number_of_alternate_modes" sysfs file
for partners and plugs is updated by a port driver.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210107034904.4112029-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Done opencode in_serving_softirq() checks in in_serving_softirq() to avoid
cluttering the code, hide them in kcov helpers instead.
Fixes: aee9ddb1d3 ("kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/aeb430c5bb90b0ccdf1ec302c70831c1a47b9c45.1609876340.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a DMA-from-stack issue in iuu_phoenix and a couple of
new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX/Wa8AAKCRALxc3C7H1l
CAEyAP4iyLa3VprQ4eFEfLiLe+TLAUj+pR3rT4wpqEOCRtiOqgEAjSDZ8we3yVVz
hKV//cmOzUdHo9gX1/QejI2NoaDsbQo=
=goVH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.11-rc3
Here's a fix for a DMA-from-stack issue in iuu_phoenix and a couple of
new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: iuu_phoenix: fix DMA from stack
USB: serial: option: add LongSung M5710 module support
USB: serial: option: add Quectel EM160R-GL
Here's another variant PNY Pro Elite USB 3.1 Gen 2 portable SSD that
hangs and doesn't respond to ATA_1x pass-through commands. If it doesn't
support these commands, it should respond properly to the host. Add it
to the unusual uas list to be able to move forward with other
operations.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2edc7af892d0913bf06f5b35e49ec463f03d5ed8.1609819418.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When binding the ConfigFS gadget to a UDC, the functions in each
configuration are added in list order. However, if usb_add_function()
fails, the failed function is put back on its configuration's
func_list and purge_configs_funcs() is called to further clean up.
purge_configs_funcs() iterates over the configurations and functions
in forward order, calling unbind() on each of the previously added
functions. But after doing so, each function gets moved to the
tail of the configuration's func_list. This results in reshuffling
the original order of the functions within a configuration such
that the failed function now appears first even though it may have
originally appeared in the middle or even end of the list. At this
point if the ConfigFS gadget is attempted to re-bind to the UDC,
the functions will be added in a different order than intended,
with the only recourse being to remove and relink the functions all
over again.
An example of this as follows:
ln -s functions/mass_storage.0 configs/c.1
ln -s functions/ncm.0 configs/c.1
ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd
echo "<udc device>" > UDC # fails
start adbd
echo "<udc device>" > UDC # now succeeds, but...
# bind order is
# "ADB", mass_storage, ncm
[30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30133.119974] using random self ethernet address
[30133.120002] using random host ethernet address
[30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26
[30133.140015] usb0: MAC 6e:28:7e:42:66:6a
[30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19
[30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200
[30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00
[30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19
[30136.661933] init: starting service 'adbd'...
[30136.700126] read descriptors
[30136.700413] read strings
[30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30138.575631] using random self ethernet address
[30138.575660] using random host ethernet address
[30138.595338] usb0: HOST MAC 2e:cf:43💿ca:c8
[30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0
[30138.791490] configfs-gadget gadget: super-speed config #1: c
Fix this by reversing the iteration order of the functions in
purge_config_funcs() when unbinding them, and adding them back to
the config's func_list at the head instead of the tail. This
ensures that we unbind and unwind back to the original list order.
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pullup does not need to be enabled at below situations:
- For platforms which the hardware pullup starts after setting
register even they do not see the VBUS. If the pullup is always
enabled for these platforms, it will consume more power and
break the USB IF compliance tests [1].
- For platforms which need to do BC 1.2 charger detection after
seeing the VBUS. Pullup D+ will break the charger detection
flow.
- For platforms which the system suspend is allowed when the
connection with host is there but the bus is not at suspend.
For these platforms, it is better to disable pullup when
entering the system suspend otherwise the host may confuse
the device behavior after controller is in low power mode.
Disable pullup is considered as a disconnection event from
host side.
[1] USB-IF Full and Low Speed Compliance Test Procedure
F Back-voltage Testing
Section 7.2.1 of the USB specification requires that no device
shall supply (source) current on VBUS at its upstream facing
port at any time. From VBUS on its upstream facing port,
a device may only draw (sink) current. They may not provide power
to the pull-up resistor on D+/D- unless VBUS is present (see
Section 7.1.5).
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201230051114.21370-1-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.
Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL
Context 2:
gadget_dev_desc_UDC_show()-> access udc_name
Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38
Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_gadget_deactivate/usb_gadget_activate does not execute the UDC start
operation, which may leave EP0 disabled and event IRQs disabled when
re-activating the function. Move the enabling/disabling of USB EP0 and
device event IRQs to be performed in the pullup routine.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Tested-by: Michael Tretter <m.tretter@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reported-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1609282837-21666-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix shift out-of-bounds in vhci_hcd.c:
UBSAN: shift-out-of-bounds in ../drivers/usb/usbip/vhci_hcd.c:399:41
shift exponent 768 is too large for 32-bit type 'int'
Fixes: 03cd00d538 ("usbip: vhci-hcd: Set the vhci structure up to work")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+297d20e437b79283bf6d@syzkaller.appspotmail.com
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201229071309.18418-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack-allocated buffers cannot be used for DMA (on all architectures) so
allocate the flush command buffer using kmalloc().
Fixes: 60a8fc0171 ("USB: add iuu_phoenix driver")
Cc: stable <stable@vger.kernel.org> # 2.6.25
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid. With URBs
sent from userspace via usbfs, that assumption can be violated.
In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests. Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits. Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.
This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings. It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold