The __diag308() inline asm temporarily changes the program check new
psw to redirect a potential program check on the diag instruction.
Restoring of the program check new psw is done in C code behind the
inline asm.
This can be problematic, especially if the function is inlined, since
the compiler can reorder instructions in such a way that a different
instruction, which may result in a program check, might be executed
before the program check new psw has been restored.
To avoid such a scenario move restoring into the inline asm. For
consistency reasons move also saving of the original program check new
psw into the inline asm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Enable ztsd support in s390/boot, to enable booting with zstd
compressed kernel when configured with CONFIG_KERNEL_ZSTD=y.
BOOT_HEAP_SIZE is defined to 0x30000 in this case. Actual decompressor
memory usage with allyesconfig is currently 0x26150.
BugLink: https://bugs.launchpad.net/bugs/1931725
Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
cc: Heiko Carstens <hca@linux.ibm.com>
cc: Vasily Gorbik <gor@linux.ibm.com>
cc: Christian Borntraeger <borntraeger@de.ibm.com>
cc: linux-s390@vger.kernel.org
Link: https://lore.kernel.org/r/20210615114150.325080-1-dimitri.ledkov@canonical.com
[gor: added BOOT_HEAP_SIZE for zstd]
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently BOOT_HEAP_SIZE is always defined as 0x400000 due to
bogus condition. Use CONFIG_KERNEL_BZIP2 instead of
CONFIG_HAVE_KERNEL_BZIP2 to correct that.
BOOT_HEAP_SIZE of 0x10000 is still good enough for every decompressor
algorithm but bzip2. Actual decompressor memory usage with allyesconfig
is the following:
gzip 0xbc28
bzip2 0x379518
xz 0x7410
lzma 0x3e6c
lzo 0
lz4 0
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove register asm usage from diag8_noresponse() since it wasn't
needed at all. There is no requirement for even/odd register pairs for
diag 0x8.
For diag_response() use register pairs to fulfill the rx+1 and ry+1
requirements as required if a response buffer is specified. Also
change the inline asm to return the condition code of the diagnose
instruction and do the conditional handling of response length
calculation in C.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Get rid of register asm statement and use a register pair.
This allows the compiler to allocate registers on its own.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Introduce a register pair union, which is supposed to be used for
inline assemblies where instructions require parameters in even/odd
numbered register pairs.
This is more or less the same register pair construct which was
available for 31 bit builds which was removed with commit 5a79859ae0
("s390: remove 31 bit support").
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
All s390 irqflags functions are very small and should be always inlined.
Therefore mark them __always_inline. This also allows to get rid of the
rather odd notrace attribute for these small functions, which was only
added to prevent tracing iff any of these functions would not be inlined.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
s390 is the only architecture which makes use of the __no_kasan_or_inline
attribute for two functions. Given that both stap() and __load_psw_mask()
are very small functions they can and should be always inlined anyway.
Therefore get rid of __no_kasan_or_inline and always inline these
functions.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When read via debugfs, s390dbf debug-views print the kernel address of
the call-site that created a trace entry. The kernel's %p pointer
hashing feature obfuscates this address, and commit 860ec7c6e2
("s390/debug: use pK for kernel pointers") made this obfuscation
configurable via the kptr_restrict sysctl.
Obfuscation of kernel address data printed via s390dbf debug-views does
not add any additional protection since the associated debugfs files are
only accessible to the root user that typically has enough other means
to obtain kernel address data.
Also trace payload data may contain binary representations of kernel
addresses as part of logged data structues. Requiring such payload data
to be obfuscated as well would be impractical and greatly diminish the
use of s390dbf.
Therefore completely remove pointer obfuscation from s390dbf
debug-views.
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since OLDMEM_BASE/OLDMEM_SIZE is already taken into consideration and is
reflected in ident_map_size. reserve/remove_oldmem() is no longer needed
and could be removed.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently there are two separate places where kernel memory layout has
to be known and adjusted:
1. early kasan setup.
2. paging setup later.
Those 2 places had to be kept in sync and adjusted to reflect peculiar
technical details of one another. With additional factors which influence
kernel memory layout like ultravisor secure storage limit, complexity
of keeping two things in sync grew up even more.
Besides that if we look forward towards creating identity mapping and
enabling DAT before jumping into uncompressed kernel - that would also
require full knowledge of and control over kernel memory layout.
So, de-duplicate and move kernel memory layout setup logic into
the decompressor.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Replace a bunch of 'p->state == TASK_RUNNING' with a new helper:
task_is_running(p).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.222401495@infradead.org
Introduce OUTSIDE macro that checks whether an instruction
address is inside or outside of a block of instructions.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Maintaining a pointer inside the aob's user-definable area is fragile
and unnecessary. At this stage we only need it to overload the buffer's
state field, and to access the buffer's TX queue.
The first part is easily solved by tracking the aob's state within the
aob itself. This also feels much cleaner and self-contained.
For enabling the access to the associated TX queue, we can store the
queue's index in the aob.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use simple sed/tr instead of perl to generate decompressor symbols
file with the same result.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
[gor: changed commit message]
Link: https://lore.kernel.org/r/a48c51f8-5fe4-87e7-284e-c96e2381801a@landley.net
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
cleanup_sie_mcck label is called from a single location only
and thus does not need to be a subroutine. Move the labelled
code to the caller - by doing that the SIE critical section
checks appear next to each other and the SIE cleanup becomes
bit more readable.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
To avoid casting ptrace members, add a union containing
both struct tpi_info and explicit int_code/int_parm members.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
For future work we need the struct tpi_info declaration in asm/ptrace.h.
Due to circular dependencies it cannot stay in asm/lowcore.h or asm/cio.h,
which would be the preferred location. Therefore add it in its own header
file.
Also fix a typo in the length of a reserved field that did not have a
functional effect beyond an incorrect field value in the s390_cio_tpi
tracepoint.
Fixes: 2ab59de7c5 ("s390/cio: Consolidate inline assemblies and related data definitions")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
APPLDATA_BASE should depend on PROC_SYSCTL instead of PROC_FS.
Building with PROC_FS but not PROC_SYSCTL causes a build error,
since appldata_base.c uses data and APIs from fs/proc/proc_sysctl.c.
arch/s390/appldata/appldata_base.o: in function `appldata_generic_handler':
appldata_base.c:(.text+0x192): undefined reference to `sysctl_vals'
Fixes: c185b783b0 ("[S390] Remove config options.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20210528002420.17634-1-rdunlap@infradead.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Though -nostdlib is passed in PURGATORY_LDFLAGS and -ffreestanding in
KBUILD_CFLAGS_DECOMPRESSOR, -fno-stack-protector must also be passed to
avoid linking errors related to undefined references to
'__stack_chk_guard' and '__stack_chk_fail' if toolchain enforces
-fstack-protector.
Fixes
- https://gitlab.com/kubu93/buildroot/-/jobs/1247043361
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/20210510053133.1220167-1-fontaine.fabrice@gmail.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
ccwgroup_notifier() currently listens for BUS_NOTIFY_UNBIND_DRIVER
events, and triggers an ungrouping for the affected device.
Looking at __device_release_driver(), we can wait for a little longer
until the driver has been fully unbound and eg. bus->remove() has been
called. So listen for BUS_NOTIFY_UNBOUND_DRIVER instead. Due to locking
the current code should work just fine, but this clarifies our intent.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Per-CPU pointer to lowcore is stored in global lowcore_ptr[]
array and duplicated in struct pcpu::lowcore member. This
update removes the redundancy.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Once the kernel is running the boot CPU lowcore becomes
freeable and does not differ from the secondary CPU ones
in any way. Make use of it and do not preserve the boot
CPU lowcore on unplugging. That allows returning unused
memory when the boot CPU is offline and makes the code
more clear.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The lowcore for IPL CPU is special. It is allocated early
in the boot process using memblock and never freed since.
The reason is pcpu_alloc_lowcore() and pcpu_free_lowcore()
routines use page allocator which is not available when
the IPL CPU is getting initialized.
Similar problem is already addressed for stacks - once the
virtual memory is available the early boot stacks get re-
allocated. Doing the same for lowcore will allow freeing
the IPL CPU lowcore and make no difference between the
boot and secondary CPUs.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Architecture callback switch_mm() is allowed to be called with
enabled interrupts. However, our implementation of switch_mm()
does not expect that. Let's follow other architectures and make
sure switch_mm() is always executed with interrupts disabled,
regardless of what happens with the generic kernel code in the
future.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Access the kernel command line via parmarea instead of using the
COMMAND_LINE define.
With this the following gcc11 warning is removed:
arch/s390/boot/ipl_parm.c: In function ‘setup_boot_command_line’:
arch/s390/boot/ipl_parm.c:168:50: warning: writing 1 byte into a region of size 0 [-Wstringop-overflow=]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit 9a965ea95135 ("s390/kexec_file: Simplify parmarea
access") we have struct parmarea which describes the layout of the
kernel parameter area.
Make the kernel parameter area available as global variable parmarea
of type struct parmarea, which allows to easily access its members.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Console name reported in /proc/consoles:
ttyS1 -W- (EC p ) 4:65
does not match the char device name:
crw--w---- 1 root root 4, 65 May 17 12:18 /dev/ttysclp0
so debian-installer inside a QEMU s390x instance gets confused and fails
to start with the following error:
steal-ctty: No such file or directory
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Link: https://lore.kernel.org/r/20210427194010.9330-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
gcc-11 warns:
arch/s390/kernel/traps.c: In function __do_pgm_check:
arch/s390/kernel/traps.c:319:17: warning: memcpy reading 256 bytes from a region of size 0 [-Wstringop-overread]
319 | memcpy(¤t->thread.trap_tdb, &S390_lowcore.pgm_tdb, 256);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding a struct pgm_tdb to struct lowcore and copy that.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
gcc-11 warns:
arch/s390/kernel/irq.c: In function do_ext_irq:
arch/s390/kernel/irq.c:175:9: warning: memcpy reading 4 bytes from a region of size 0 [-Wstringop-overread]
175 | memcpy(®s->int_code, &S390_lowcore.ext_cpu_addr, 4);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding a struct for int_code to struct lowcore.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With gcc-11, there are a lot of warnings because the facility functions
are accessing lowcore through a null pointer. Fix this by moving the
facility arrays away from lowcore.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
arch/s390/kernel/syscall.c: In function __do_syscall:
arch/s390/kernel/syscall.c:147:9: warning: memcpy reading 64 bytes from a region of size 0 [-Wstringop-overread]
147 | memcpy(®s->gprs[8], S390_lowcore.save_area_sync, 8 * sizeof(unsigned long));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/s390/kernel/syscall.c:148:9: warning: memcpy reading 4 bytes from a region of size 0 [-Wstringop-overread]
148 | memcpy(®s->int_code, &S390_lowcore.svc_ilc, sizeof(regs->int_code));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by moving the gprs restore from C to assembly, and use a assignment
for int_code instead of memcpy.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
In commit b02002cc4c ("s390/pci: Implement ioremap_wc/prot() with
MIO") we implemented both ioremap_wc() and ioremap_prot() however until
now we had not set HAVE_IOREMAP_PROT in Kconfig, do so now.
This also requires implementing pte_pgprot() as this is used in the
generic_access_phys() code enabled by CONFIG_HAVE_IOREMAP_PROT. As with
ioremap_wc() we need to take the MMIO Write Back bit index into account.
Moreover since the pgprot value returned from pte_pgprot() is to be used
for mappings into kernel address space we must make sure that it uses
appropriate kernel page table protection bits. In particular a pgprot
value originally coming from userspace could have the _PAGE_PROTECT
bit set to enable fault based dirty bit accounting which would then make
the mapping inaccessible when used in kernel address space.
Fixes: b02002cc4c ("s390/pci: Implement ioremap_wc/prot() with MIO")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove some WARN_ON_ONCE() warnings when a counter is started. Each
counter is installed function calls
event_sched_in() --> cpumf_pmu_add(..., PERF_EF_START).
This is done after the event has been created using
perf_pmu_event_init() which verifies the counter is valid.
Member hwc->config must be valid at this point.
Function cpumf_pmu_start(..., PERF_EF_RELOAD) is called from
function cpumf_pmu_add() for counter events. All other invocations of
cpumf_pmu_start(..., PERF_EF_RELOAD) are from the performance subsystem
for sampling events.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The command 'perf stat -e cycles ...' triggers the following function
sequence in the CPU Measurement Facility counter device driver:
perf_pmu_event_init()
__hw_perf_event_init()
validate_ctr_auth()
validate_ctr_version()
During event creation, the counter number is checked in functions
validate_ctr_auth() and validate_ctr_version() to verify it is a valid
counter and supported by the hardware. If this is not the case, both
functions return an error and the event is not created. System call
perf_event_open() returns an error in this case.
Later on the event is installed in the kernel event subsystem and the
driver functions cpumf_pmu_add() and cpumf_pmu_commit_txn() are called
to install the counter event by the hardware.
Since both events have been verified at event creation, there is no need
to re-evaluate the authorization state. This can not change since on
* LPARs the authorization change requires a restart of the LPAR (and
thus a reboot of the kernel)
* DPMs can not take resources away, just add them.
Also the sequence of CPU Measurement facility counter device driver
calls is
cpumf_pmu_start_txn
cpumf_pmu_add
cpumf_pmu_start
cpumf_pmu_commit_txn
for every single event. Which means the condition in cpumf_pmu_add()
is never met and validate_ctr_auth() is never called.
This leaves the counter device driver transaction functions with
just one task:
start_txn: Verify a transaction is not in flight and call
perf_pmu_disable()
cancel_txn, commit_txn: Verify a transaction is in flight and call
perf_pmu_enable()
The same functionality is provided by the default transaction handling
functions in kernel/events/core.c. Use those by removing the
counter device driver private call back functions.
Suggested-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Wrong condition check is used to decide if a machine check hit
while in KVM guest. As result of this check the instruction
following the SIE critical section might be considered as still
in KVM guest and _CIF_MCCK_GUEST CPU flag mistakenly set as
result.
Fixes: c929500d7a ("s390/nmi: s390: New low level handling for machine check happening in guest")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The size of SIE critical section is calculated wrongly
as result of a missed subtraction in commit 0b0ed657fe
("s390: remove critical section cleanup from entry.S")
Fixes: 0b0ed657fe ("s390: remove critical section cleanup from entry.S")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
In an upcoming change we would like to add a flag to
GFP_HIGHUSER_MOVABLE so that it would no longer be an OR
of GFP_HIGHUSER and __GFP_MOVABLE. This poses a problem for
alloc_zeroed_user_highpage_movable() which passes __GFP_MOVABLE
into an arch-specific __alloc_zeroed_user_highpage() hook which ORs
in GFP_HIGHUSER.
Since __alloc_zeroed_user_highpage() is only ever called from
alloc_zeroed_user_highpage_movable(), we can remove one level
of indirection here. Remove __alloc_zeroed_user_highpage(),
make alloc_zeroed_user_highpage_movable() the hook, and use
GFP_HIGHUSER_MOVABLE in the hook implementations so that they will
pick up the new flag that we are going to add.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ic6361c657b2cdcd896adbe0cf7cb5a7fbb1ed7bf
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210602235230.3928842-2-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Kprobes has a counter 'nmissed', that is used to count the number of
times a probe handler was not called. This generally happens when we hit
a kprobe while handling another kprobe.
However, if one of the probe handlers causes a fault, we are currently
incrementing 'nmissed'. The comment in fault handler indicates that this
can be used to account faults taken by the probe handlers. But, this has
never been the intention as is evident from the comment above 'nmissed'
in 'struct kprobe':
/*count the number of times this probe was temporarily disarmed */
unsigned long nmissed;
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lkml.kernel.org/r/20210601120150.672652-1-naveen.n.rao@linux.vnet.ibm.com
The reason for kprobe::fault_handler(), as given by their comment:
* We come here because instructions in the pre/post
* handler caused the page_fault, this could happen
* if handler tries to access user space by
* copy_from_user(), get_user() etc. Let the
* user-specified handler try to fix it first.
Is just plain bad. Those other handlers are ran from non-preemptible
context and had better use _nofault() functions. Also, there is no
upstream usage of this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20210525073213.561116662@infradead.org
arch/$(SRCARCH)/Kbuild is useful for Makefile cleanups because you can
use the obj-y syntax.
Add an empty file if it is missing in arch/$(SRCARCH)/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Now that all architectures implement ARCH_ATOMIC, we can make it
mandatory, removing the Kconfig symbol and logic for !ARCH_ATOMIC.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210525140232.53872-33-mark.rutland@arm.com
Subsequent patches will move architectures over to the ARCH_ATOMIC API,
after preparing the asm-generic atomic implementations to function with
or without ARCH_ATOMIC.
As some architectures use the asm-generic implementations exclusively
(and don't have a local atomic.h), and to avoid the risk that
ARCH_ATOMIC isn't defined in some cases we expect, let's make the
ARCH_ATOMIC macro a Kconfig symbol instead, so that we can guarantee it
is consistently available where needed.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210525140232.53872-2-mark.rutland@arm.com
In commit fa8b90070a ("quota: wire up quotactl_path") we have wired up
new quotactl_path syscall. However some people in LWN discussion have
objected that the path based syscall is missing dirfd and flags argument
which is mostly standard for contemporary path based syscalls. Indeed
they have a point and after a discussion with Christian Brauner and
Sascha Hauer I've decided to disable the syscall for now and update its
API. Since there is no userspace currently using that syscall and it
hasn't been released in any major release, we should be fine.
CC: Christian Brauner <christian.brauner@ubuntu.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/lkml/20210512153621.n5u43jsytbik4yze@wittgenstein
Signed-off-by: Jan Kara <jack@suse.cz>
As pointed out by commit
de9b8f5dcb ("sched: Fix crash trying to dequeue/enqueue the idle thread")
init_idle() can and will be invoked more than once on the same idle
task. At boot time, it is invoked for the boot CPU thread by
sched_init(). Then smp_init() creates the threads for all the secondary
CPUs and invokes init_idle() on them.
As the hotplug machinery brings the secondaries to life, it will issue
calls to idle_thread_get(), which itself invokes init_idle() yet again.
In this case it's invoked twice more per secondary: at _cpu_up(), and at
bringup_cpu().
Given smp_init() already initializes the idle tasks for all *possible*
CPUs, no further initialization should be required. Now, removing
init_idle() from idle_thread_get() exposes some interesting expectations
with regards to the idle task's preempt_count: the secondary startup always
issues a preempt_disable(), requiring some reset of the preempt count to 0
between hot-unplug and hotplug, which is currently served by
idle_thread_get() -> idle_init().
Given the idle task is supposed to have preemption disabled once and never
see it re-enabled, it seems that what we actually want is to initialize its
preempt_count to PREEMPT_DISABLED and leave it there. Do that, and remove
init_idle() from idle_thread_get().
Secondary startups were patched via coccinelle:
@begone@
@@
-preempt_disable();
...
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE);
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210512094636.2958515-1-valentin.schneider@arm.com
- add support for system call stack randomization.
- handle stale PCI deconfiguration events.
- couple of defconfig updates.
- some fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEECMNfWEw3SLnmiLkZIg7DeRspbsIFAmCURRgACgkQIg7DeRsp
bsLiVw//ThqXjgP7koJtawL0MFvSo1V69KTw1QNoMmUvrCynZ8nJlt4sHj1LIuEN
m7kHoWUsvNcg8r8QbxL1eZ2f/Qf43qrFjXIKi5iTdOtO/LF9NNNQYFnA3cT3h9oE
7hfycj8o5yi+KYY3Ca2HjlQ0i7zKYfPul1+Yms5h0nAgcvOXuPltVAlyYrrtddrM
cfpolZZd1IB/lMHSa8/qLviRB5ADlrNx4N6Y1ROeCPCWDbO8flrnDOPTDG8a8sCN
llQ0/vBTmenkGyT7UjG5bx9P/gX1FsMShBtyZMa8t8leIJfruDiwdo87wvSDf5IT
I612xdbLpMfGy6i/LnJHhnw61FkpwBKJZ3UrVVkrmjY8IVN8tVdAjy5s4Fplhgjj
BUbk9Ep03YCqfO6fpqh5DkBxCF0dnj4dZrcHA881/DnZuUkxpMJhyNjJDIx1OLup
PC+y9eILFAnDveFvhZJZeMpH7wAheyrW/WgKZsZNLYZ+61pKPyGn9RrE5UBgI7ra
CSIi9Km/lAuNCd9o4n5/5wCd3a9dW47kCrRe3S20oF57v5RU3AVtbC2YSUqPYahf
NR4ZgL+zDhByLPRVij5FJ1LLeaJJftKM9uUO9egHOk1JnSxDc9EyU41x4838SKYv
CfhQJw1ISTTRNCGeflE7+CBfEYCKX7h+DySVCtxTsg6PelcQHLs=
=C1HZ
-----END PGP SIGNATURE-----
Merge tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- add support for system call stack randomization
- handle stale PCI deconfiguration events
- couple of defconfig updates
- some fixes and cleanups
* tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix detection of vector enhancements facility 1 vs. vector packed decimal facility
s390/entry: add support for syscall stack randomization
s390/configs: change CONFIG_VIRTIO_CONSOLE to "m"
s390/cio: remove invalid condition on IO_SCH_UNREG
s390/cpumf: remove call to perf_event_update_userpage
s390/cpumf: move counter set size calculation to common place
s390/cpumf: beautify if-then-else indentation
s390/configs: enable CONFIG_PCI_IOV
s390/pci: handle stale deconfiguration events
s390/pci: rename zpci_configure_device()
Merge more updates from Andrew Morton:
"The remainder of the main mm/ queue.
143 patches.
Subsystems affected by this patch series (all mm): pagecache, hugetlb,
userfaultfd, vmscan, compaction, migration, cma, ksm, vmstat, mmap,
kconfig, util, memory-hotplug, zswap, zsmalloc, highmem, cleanups, and
kfence"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (143 commits)
kfence: use power-efficient work queue to run delayed work
kfence: maximize allocation wait timeout duration
kfence: await for allocation using wait_event
kfence: zero guard page after out-of-bounds access
mm/process_vm_access.c: remove duplicate include
mm/mempool: minor coding style tweaks
mm/highmem.c: fix coding style issue
btrfs: use memzero_page() instead of open coded kmap pattern
iov_iter: lift memzero_page() to highmem.h
mm/zsmalloc: use BUG_ON instead of if condition followed by BUG.
mm/zswap.c: switch from strlcpy to strscpy
arm64/Kconfig: introduce ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE
x86/Kconfig: introduce ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE
mm,memory_hotplug: add kernel boot option to enable memmap_on_memory
acpi,memhotplug: enable MHP_MEMMAP_ON_MEMORY when supported
mm,memory_hotplug: allocate memmap from the added memory range
mm,memory_hotplug: factor out adjusting present pages into adjust_present_page_count()
mm,memory_hotplug: relax fully spanned sections check
drivers/base/memory: introduce memory_block_{online,offline}
mm/memory_hotplug: remove broken locking of zone PCP structures during hot remove
...
Patch series "hugetlb: Disable huge pmd unshare for uffd-wp", v4.
This series tries to disable huge pmd unshare of hugetlbfs backed memory
for uffd-wp. Although uffd-wp of hugetlbfs is still during rfc stage,
the idea of this series may be needed for multiple tasks (Axel's uffd
minor fault series, and Mike's soft dirty series), so I picked it out
from the larger series.
This patch (of 4):
It is a preparation work to be able to behave differently in the per
architecture huge_pte_alloc() according to different VMA attributes.
Pass it deeper into huge_pmd_share() so that we can avoid the find_vma() call.
[peterx@redhat.com: build fix]
Link: https://lkml.kernel.org/r/20210304164653.GB397383@xz-x1Link: https://lkml.kernel.org/r/20210218230633.15028-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210218230633.15028-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PoP documents:
134: The vector packed decimal facility is installed in the
z/Architecture architectural mode. When bit 134 is
one, bit 129 is also one.
135: The vector enhancements facility 1 is installed in
the z/Architecture architectural mode. When bit 135
is one, bit 129 is also one.
Looks like we confuse the vector enhancements facility 1 ("EXT") with the
Vector packed decimal facility ("BCD"). Let's fix the facility checks.
Detected while working on QEMU/tcg z14 support and only unlocking
the vector enhancements facility 1, but not the vector packed decimal
facility.
Fixes: 2583b848ca ("s390: report new vector facilities")
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20210503121244.25232-1-david@redhat.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----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=uCN4
-----END PGP SIGNATURE-----
Merge tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull Landlock LSM from James Morris:
"Add Landlock, a new LSM from Mickaël Salaün.
Briefly, Landlock provides for unprivileged application sandboxing.
From Mickaël's cover letter:
"The goal of Landlock is to enable to restrict ambient rights (e.g.
global filesystem access) for a set of processes. Because Landlock
is a stackable LSM [1], it makes possible to create safe security
sandboxes as new security layers in addition to the existing
system-wide access-controls. This kind of sandbox is expected to
help mitigate the security impact of bugs or unexpected/malicious
behaviors in user-space applications. Landlock empowers any
process, including unprivileged ones, to securely restrict
themselves.
Landlock is inspired by seccomp-bpf but instead of filtering
syscalls and their raw arguments, a Landlock rule can restrict the
use of kernel objects like file hierarchies, according to the
kernel semantic. Landlock also takes inspiration from other OS
sandbox mechanisms: XNU Sandbox, FreeBSD Capsicum or OpenBSD
Pledge/Unveil.
In this current form, Landlock misses some access-control features.
This enables to minimize this patch series and ease review. This
series still addresses multiple use cases, especially with the
combined use of seccomp-bpf: applications with built-in sandboxing,
init systems, security sandbox tools and security-oriented APIs [2]"
The cover letter and v34 posting is here:
https://lore.kernel.org/linux-security-module/20210422154123.13086-1-mic@digikod.net/
See also:
https://landlock.io/
This code has had extensive design discussion and review over several
years"
Link: https://lore.kernel.org/lkml/50db058a-7dde-441b-a7f9-f6837fe8b69f@schaufler-ca.com/ [1]
Link: https://lore.kernel.org/lkml/f646e1c7-33cf-333f-070c-0a40ad0468cd@digikod.net/ [2]
* tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
landlock: Enable user space to infer supported features
landlock: Add user and kernel documentation
samples/landlock: Add a sandbox manager example
selftests/landlock: Add user space tests
landlock: Add syscall implementations
arch: Wire up Landlock syscalls
fs,security: Add sb_delete hook
landlock: Support filesystem access-control
LSM: Infrastructure management of the superblock
landlock: Add ptrace restrictions
landlock: Set up the security framework and manage credentials
landlock: Add ruleset and domain management
landlock: Add object management
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
Merge misc updates from Andrew Morton:
"A few misc subsystems and some of MM.
175 patches.
Subsystems affected by this patch series: ia64, kbuild, scripts, sh,
ocfs2, kfifo, vfs, kernel/watchdog, and mm (slab-generic, slub,
kmemleak, debug, pagecache, msync, gup, memremap, memcg, pagemap,
mremap, dma, sparsemem, vmalloc, documentation, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (175 commits)
mm/memory-failure: unnecessary amount of unmapping
mm/mmzone.h: fix existing kernel-doc comments and link them to core-api
mm: page_alloc: ignore init_on_free=1 for debug_pagealloc=1
net: page_pool: use alloc_pages_bulk in refill code path
net: page_pool: refactor dma_map into own function page_pool_dma_map
SUNRPC: refresh rq_pages using a bulk page allocator
SUNRPC: set rq_page_end differently
mm/page_alloc: inline __rmqueue_pcplist
mm/page_alloc: optimize code layout for __alloc_pages_bulk
mm/page_alloc: add an array-based interface to the bulk page allocator
mm/page_alloc: add a bulk page allocator
mm/page_alloc: rename alloced to allocated
mm/page_alloc: duplicate include linux/vmalloc.h
mm, page_alloc: avoid page_to_pfn() in move_freepages()
mm/Kconfig: remove default DISCONTIGMEM_MANUAL
mm: page_alloc: dump migrate-failed pages
mm/mempolicy: fix mpol_misplaced kernel-doc
mm/mempolicy: rewrite alloc_pages_vma documentation
mm/mempolicy: rewrite alloc_pages documentation
mm/mempolicy: rename alloc_pages_current to alloc_pages
...
- Enable KFENCE for 32-bit.
- Implement EBPF for 32-bit.
- Convert 32-bit to do interrupt entry/exit in C.
- Convert 64-bit BookE to do interrupt entry/exit in C.
- Changes to our signal handling code to use user_access_begin/end() more extensively.
- Add support for time namespaces (CONFIG_TIME_NS)
- A series of fixes that allow us to reenable STRICT_KERNEL_RWX.
- Other smaller features, fixes & cleanups.
Thanks to: Alexey Kardashevskiy, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Athira Rajeev, Bhaskar Chowdhury, Bixuan Cui, Cédric Le Goater, Chen Huang, Chris
Packham, Christophe Leroy, Christopher M. Riedl, Colin Ian King, Dan Carpenter, Daniel
Axtens, Daniel Henrique Barboza, David Gibson, Davidlohr Bueso, Denis Efremov,
dingsenjie, Dmitry Safonov, Dominic DeMarco, Fabiano Rosas, Ganesh Goudar, Geert
Uytterhoeven, Geetika Moolchandani, Greg Kurz, Guenter Roeck, Haren Myneni, He Ying,
Jiapeng Chong, Jordan Niethe, Laurent Dufour, Lee Jones, Leonardo Bras, Li Huafei,
Madhavan Srinivasan, Mahesh Salgaonkar, Masahiro Yamada, Nathan Chancellor, Nathan
Lynch, Nicholas Piggin, Oliver O'Halloran, Paul Menzel, Pu Lehui, Randy Dunlap, Ravi
Bangoria, Rosen Penev, Russell Currey, Santosh Sivaraj, Sebastian Andrzej Siewior,
Segher Boessenkool, Shivaprasad G Bhat, Srikar Dronamraju, Stephen Rothwell, Thadeu Lima
de Souza Cascardo, Thomas Gleixner, Tony Ambardar, Tyrel Datwyler, Vaibhav Jain,
Vincenzo Frascino, Xiongwei Song, Yang Li, Yu Kuai, Zhang Yunkai.
-----BEGIN PGP SIGNATURE-----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=dfKL
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Enable KFENCE for 32-bit.
- Implement EBPF for 32-bit.
- Convert 32-bit to do interrupt entry/exit in C.
- Convert 64-bit BookE to do interrupt entry/exit in C.
- Changes to our signal handling code to use user_access_begin/end()
more extensively.
- Add support for time namespaces (CONFIG_TIME_NS)
- A series of fixes that allow us to reenable STRICT_KERNEL_RWX.
- Other smaller features, fixes & cleanups.
Thanks to Alexey Kardashevskiy, Andreas Schwab, Andrew Donnellan, Aneesh
Kumar K.V, Athira Rajeev, Bhaskar Chowdhury, Bixuan Cui, Cédric Le
Goater, Chen Huang, Chris Packham, Christophe Leroy, Christopher M.
Riedl, Colin Ian King, Dan Carpenter, Daniel Axtens, Daniel Henrique
Barboza, David Gibson, Davidlohr Bueso, Denis Efremov, dingsenjie,
Dmitry Safonov, Dominic DeMarco, Fabiano Rosas, Ganesh Goudar, Geert
Uytterhoeven, Geetika Moolchandani, Greg Kurz, Guenter Roeck, Haren
Myneni, He Ying, Jiapeng Chong, Jordan Niethe, Laurent Dufour, Lee
Jones, Leonardo Bras, Li Huafei, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Nathan Chancellor, Nathan Lynch, Nicholas Piggin,
Oliver O'Halloran, Paul Menzel, Pu Lehui, Randy Dunlap, Ravi Bangoria,
Rosen Penev, Russell Currey, Santosh Sivaraj, Sebastian Andrzej Siewior,
Segher Boessenkool, Shivaprasad G Bhat, Srikar Dronamraju, Stephen
Rothwell, Thadeu Lima de Souza Cascardo, Thomas Gleixner, Tony Ambardar,
Tyrel Datwyler, Vaibhav Jain, Vincenzo Frascino, Xiongwei Song, Yang Li,
Yu Kuai, and Zhang Yunkai.
* tag 'powerpc-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (302 commits)
powerpc/signal32: Fix erroneous SIGSEGV on RT signal return
powerpc: Avoid clang uninitialized warning in __get_user_size_allowed
powerpc/papr_scm: Mark nvdimm as unarmed if needed during probe
powerpc/kvm: Fix build error when PPC_MEM_KEYS/PPC_PSERIES=n
powerpc/kasan: Fix shadow start address with modules
powerpc/kernel/iommu: Use largepool as a last resort when !largealloc
powerpc/kernel/iommu: Align size for IOMMU_PAGE_SIZE() to save TCEs
powerpc/44x: fix spelling mistake in Kconfig "varients" -> "variants"
powerpc/iommu: Annotate nested lock for lockdep
powerpc/iommu: Do not immediately panic when failed IOMMU table allocation
powerpc/iommu: Allocate it_map by vmalloc
selftests/powerpc: remove unneeded semicolon
powerpc/64s: remove unneeded semicolon
powerpc/eeh: remove unneeded semicolon
powerpc/selftests: Add selftest to test concurrent perf/ptrace events
powerpc/selftests/perf-hwbreak: Add testcases for 2nd DAWR
powerpc/selftests/perf-hwbreak: Coalesce event creation code
powerpc/selftests/ptrace-hwbreak: Add testcases for 2nd DAWR
powerpc/configs: Add IBMVNIC to some 64-bit configs
selftests/powerpc: Add uaccess flush test
...
mem_init_print_info() is called in mem_init() on each architecture, and
pass NULL argument, so using void argument and move it into mm_init().
Link: https://lkml.kernel.org/r/20210317015210.33641-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> [x86]
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr> [powerpc]
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com> [sparc64]
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> [arm]
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for adding a random offset to the stack while handling
syscalls. The patch uses get_tod_clock_fast() as this is considered good
enough and has much less performance penalty compared to using
get_random_int(). The patch also adds randomization in pgm_check_handler()
as the sigreturn/rt_sigreturn system calls might be called from there.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20210429091451.1062594-1-svens@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In former times, the virtio-console code had to be compiled into
the kernel since the old guest virtio transport had some hard de-
pendencies. But since the old virtio transport has been removed in
commit 7fb2b2d512 ("s390/virtio: remove the old KVM virtio transport"),
we do not have this limitation anymore.
Commit bb533ec8ba ("s390/config: do not select VIRTIO_CONSOLE via
Kconfig") then also lifted the hard setting in the Kconfig system, so
we can finally switch the CONFIG_VIRTIO_CONSOLE knob to compile this
driver as a module now, making it more flexible for the user to only
load it if it is really required.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/r/20210428082442.321327-1-thuth@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The function cpumf_pmu_add and cpumf_pmu_del call function
perf_event_update_userpage(). This calls is obsolete, the calls add and
delete a counter event. Counter events do not sample data and the
event->rb member to access the sampling ring buffer is always NULL.
The function perf_event_update_userpage() simply returns in this case.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by : Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The function to calculate the size of counter sets is renamed from
cf_diag_ctrset_size() to cpum_cf_ctrset_size() and moved to the file
containing common functions for the CPU Measurement Counter Facility.
No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by : Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Beautify if-then-else indentation to match coding guideline.
Also use shorter pointer notation hwc instead of event->hw.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by : Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
All major distributions ship with CONFIG_PCI_IOV=y so let us enable it
for our defconfigs as well.
Note also that since commit e5794cf1a2 ("s390/pci: create links
between PFs and VFs") we enabled proper linking between PFs and their
associated VFs so with this commit and its fixes applied we can fully
support handling SR-IOV enabled PFs.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The PCIs event with PEC 0x0303 or 0x0304 are a request to deconfigure
a PCI function, respectively an indication that it was already
deconfigured by the platform. If such an event is queued during boot it
may happen that the platform has already adjusted the configuration flag
of the relevant function in the CLP List PCI Functions result. In this
case we might not have configured the PCI function at all and should
thus ignore the event. Note that no locking is necessary as event
handling only starts after we have fully initialized the zPCI subsystem
and scanned all PCI devices listed in the CLP result.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
With zpci_configure_device() now always called on a device that has
already been configured on the platform level its name has become
misleading. Rename it to zpci_scan_configured_device() to signify that
the function now only handles the correct scanning of a newly configured
PCI function taking care of the special handling necessary for function
0 and functions parked waiting for a PCI bus that can't be created
without first seeing function 0.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmCJU1UACgkQnJ2qBz9k
QNk62AgAgp05OIXU/AgObb7DvSyI3ycwCV8PeWBpwD8yoDAh5x0tmT7vnJu974p6
yHdnF7rr69ZzvbNCHLJ5kRykRlUao9W7cO5fdOW1uTpL7Ic60QuJMks/NfgVTHp1
2zIQmBDerfn1/LTK8r2pPGcvtcjRcr7Ep4beN0Duw57lfVMJhjsNRPnBbXGBcp0r
QzKk4/8V3DCZvOw+XNC3nto7avjvf+nU9sJmuh83546eqh0atjWivvO5aAlDOe6W
rhBiLlmP0in5u2n1fYqzI1OQvtgtleyEZT2G0CrbAZn0xjmV/if9wl+3K6TOwDvR
778xDEX7sZCaO/xkB+WK3hrd15ftKg==
=0kYE
-----END PGP SIGNATURE-----
Merge tag 'for_v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota, ext2, reiserfs updates from Jan Kara:
- support for path (instead of device) based quotactl syscall
(quotactl_path(2))
- ext2 conversion to kmap_local()
- other minor cleanups & fixes
* tag 'for_v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs/reiserfs/journal.c: delete useless variables
fs/ext2: Replace kmap() with kmap_local_page()
ext2: Match up ext2_put_page() with ext2_dotdot() and ext2_find_entry()
fs/ext2/: fix misspellings using codespell tool
quota: report warning limits for realtime space quotas
quota: wire up quotactl_path
quota: Add mountpath based quota support
- fix buffer size for in-kernel disassembler for ebpf programs.
- fix two memory leaks in zcrypt driver.
- expose PCI device UID as index, including an indicator if the uid is
unique.
- remove some oprofile leftovers.
- improve stack unwinder tests.
- don't use gcc atomic builtins anymore, just like all other
architectures. Even though I'm sure the current code is ok, I
totally dislike that s390 is the only architecture being special
here; especially considering that there was a lengthly discussion
about this topic and the outcome was not to use the builtins.
Therefore open-code atomic ops again with inline assembly and switch
to gcc builtins as soon as other architectures are doing.
- couple of other changes to atomic and cmpxchg, and use
atomic-instrumented.h for KASAN.
- separate zbus creation, registration, and scanning in our PCI code
which allows for cleaner and easier handling.
- a rather large change to the vfio-ap code to fix circular locking
dependencies when updating crypto masks.
- move QAOB handling from qdio layer down to drivers.
- add CRW inject facility to common I/O layer. This adds debugs files
which allow to generate artificial events from user space for
testing purposes.
- increase SCLP console line length from 80 to 320 characters to avoid
odd wrapped lines.
- add protected virtualization guest and host indication files, which
indicate either that a guest is running in pv mode or if the
hypervisor is capable of starting pv guests.
- various other small fixes and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=e+mh
-----END PGP SIGNATURE-----
Merge tag 's390-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- fix buffer size for in-kernel disassembler for ebpf programs.
- fix two memory leaks in zcrypt driver.
- expose PCI device UID as index, including an indicator if the uid is
unique.
- remove some oprofile leftovers.
- improve stack unwinder tests.
- don't use gcc atomic builtins anymore, just like all other
architectures. Even though I'm sure the current code is ok, I totally
dislike that s390 is the only architecture being special here;
especially considering that there was a lengthly discussion about
this topic and the outcome was not to use the builtins. Therefore
open-code atomic ops again with inline assembly and switch to gcc
builtins as soon as other architectures are doing.
- couple of other changes to atomic and cmpxchg, and use
atomic-instrumented.h for KASAN.
- separate zbus creation, registration, and scanning in our PCI code
which allows for cleaner and easier handling.
- a rather large change to the vfio-ap code to fix circular locking
dependencies when updating crypto masks.
- move QAOB handling from qdio layer down to drivers.
- add CRW inject facility to common I/O layer. This adds debugs files
which allow to generate artificial events from user space for testing
purposes.
- increase SCLP console line length from 80 to 320 characters to avoid
odd wrapped lines.
- add protected virtualization guest and host indication files, which
indicate either that a guest is running in pv mode or if the
hypervisor is capable of starting pv guests.
- various other small fixes and improvements all over the place.
* tag 's390-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (53 commits)
s390/disassembler: increase ebpf disasm buffer size
s390/archrandom: add parameter check for s390_arch_random_generate
s390/zcrypt: fix zcard and zqueue hot-unplug memleak
s390/pci: expose a PCI device's UID as its index
s390/atomic,cmpxchg: always inline __xchg/__cmpxchg
s390/smp: fix do_restart() prototype
s390: get rid of oprofile leftovers
s390/atomic,cmpxchg: make constraints work with old compilers
s390/test_unwind: print test suite start/end info
s390/cmpxchg: use unsigned long values instead of void pointers
s390/test_unwind: add WARN if tests failed
s390/test_unwind: unify error handling paths
s390: update defconfigs
s390/spinlock: use R constraint in inline assembly
s390/atomic,cmpxchg: switch to use atomic-instrumented.h
s390/cmpxchg: get rid of gcc atomic builtins
s390/atomic: get rid of gcc atomic builtins
s390/atomic: use proper constraints
s390/atomic: move remaining inline assemblies to atomic_ops.h
s390/bitops: make bitops only work on longs
...
-----BEGIN PGP SIGNATURE-----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=bO1i
-----END PGP SIGNATURE-----
Merge tag 'x86_cleanups_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 cleanups from Borislav Petkov:
"Trivial cleanups and fixes all over the place"
* tag 'x86_cleanups_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Remove me from IDE/ATAPI section
x86/pat: Do not compile stubbed functions when X86_PAT is off
x86/asm: Ensure asm/proto.h can be included stand-alone
x86/platform/intel/quark: Fix incorrect kernel-doc comment syntax in files
x86/msr: Make locally used functions static
x86/cacheinfo: Remove unneeded dead-store initialization
x86/process/64: Move cpu_current_top_of_stack out of TSS
tools/turbostat: Unmark non-kernel-doc comment
x86/syscalls: Fix -Wmissing-prototypes warnings from COND_SYSCALL()
x86/fpu/math-emu: Fix function cast warning
x86/msr: Fix wr/rdmsr_safe_regs_on_cpu() prototypes
x86: Fix various typos in comments, take #2
x86: Remove unusual Unicode characters from comments
x86/kaslr: Return boolean values from a function returning bool
x86: Fix various typos in comments
x86/setup: Remove unused RESERVE_BRK_ARRAY()
stacktrace: Move documentation for arch_stack_walk_reliable() to header
x86: Remove duplicate TSC DEADLINE MSR definitions
New features:
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
- Alexandru is now a reviewer (not really a new feature...)
Fixes:
- Proper emulation of the GICR_TYPER register
- Handle the complete set of relocation in the nVHE EL2 object
- Get rid of the oprofile dependency in the PMU code (and of the
oprofile body parts at the same time)
- Debug and SPE fixes
- Fix vcpu reset
-----BEGIN PGP SIGNATURE-----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=fpey
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for Linux 5.13
New features:
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
- Alexandru is now a reviewer (not really a new feature...)
Fixes:
- Proper emulation of the GICR_TYPER register
- Handle the complete set of relocation in the nVHE EL2 object
- Get rid of the oprofile dependency in the PMU code (and of the
oprofile body parts at the same time)
- Debug and SPE fixes
- Fix vcpu reset
A review of the code showed, that this function which is exposed
within the whole kernel should do a parameter check for the
amount of bytes requested. If this requested bytes is too high
an unsigned int overflow could happen causing this function to
try to memcpy a really big memory chunk.
This is not a security issue as there are only two invocations
of this function from arch/s390/include/asm/archrandom.h and both
are not exposed to userland.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
On s390 each PCI device has a user-defined ID (UID) exposed under
/sys/bus/pci/devices/<dev>/uid. This ID was designed to serve as the PCI
device's primary index and to match the device within Linux to the
device configured in the hypervisor. To serve as a primary identifier
the UID must be unique within the Linux instance, this is guaranteed by
the platform if and only if the UID Uniqueness Checking flag is set
within the CLP List PCI Functions response.
In this sense the UID serves an analogous function as the SMBIOS
instance number or ACPI index exposed as the "index" respectively
"acpi_index" device attributes and used by e.g. systemd to set interface
names. As s390 does not use and will likely never use ACPI nor SMBIOS
there is no conflict and we can just expose the UID under the "index"
attribute whenever UID Uniqueness Checking is active and get systemd's
interface naming support for free.
Link: https://lore.kernel.org/lkml/20210412135905.1434249-1-schnelle@linux.ibm.com/
Acked-by: Viktor Mihajlovski <mihajlov@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Make sure to always inline __xchg() and __cmpxchg() otherwise the
compiler might decide to generate out-of-line versions which will
fail at link time:
s390-linux-ld: lib/atomic64_test.o: in function `__xchg':
>> atomic64_test.c:(.text.unlikely+0xa4): undefined reference to `__xchg_called_with_bad_pointer'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-mm/202104170449.SIIFKVjT-lkp@intel.com/
Fixes: d2b1f6d2d3 ("s390/cmpxchg: get rid of gcc atomic builtins")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Funciton do_restart() is a callback invoked from the
restart CPU routine and passed a single parameter.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define KVM_GUESTDBG_VALID_MASK and use it to implement this capabiity.
Compile tested only.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20210401135451.1004564-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a potential race for preemptible kernels, where
the host kernel would get a fault when it is preempted as
the wrong point in time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CsvI
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fix potential crash in preemptible kernels
There is a potential race for preemptible kernels, where
the host kernel would get a fault when it is preempted as
the wrong point in time.
Old gcc versions may fail with an internal compiler error if only the
T or S constraint is specified for an operand, and no displacement is
needed at all.
To fix this use RT and QS as constraints, which reflects the union of
both. Later gcc versions do the right thing and always accept single T
and S constraints.
See gcc commit 3e4be43f69da ("S/390: Memory constraint cleanup").
Fixes: ca897bb181 ("s390/atomic: use proper constraints")
Fixes: b23eb636d7 ("s390/atomic: get rid of gcc atomic builtins")
Fixes: d2b1f6d2d3 ("s390/cmpxchg: get rid of gcc atomic builtins")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add couple of additional info lines to make it easier to match
test suite output and results.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
gcc and clang warn about incompatible pointer types due to the recent
cmpxchg changes:
drivers/gpu/drm/drm_lock.c:75:10: error: passing 'typeof (lock)' (aka 'volatile unsigned int *') to parameter of type 'void *' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
prev = cmpxchg(lock, old, new);
^~~~~~~~~~~~~~~~~~~~~~~
include/asm-generic/atomic-instrumented.h:1685:2: note: expanded from macro 'cmpxchg'
arch_cmpxchg(__ai_ptr, __VA_ARGS__); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
To avoid this simply cast pointers to unsigned long and use them
instead of void pointers. This allows to stay with functions, instead
of using complex defines and having to deal with all their potential
side effects.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d2b1f6d2d3 ("s390/cmpxchg: get rid of gcc atomic builtins")
Link: https://lore.kernel.org/linux-s390/202104130131.sMmSqpb5-lkp@intel.com/
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
store_regs_fmt2() has an ordering problem: first the guarded storage
facility is enabled on the local cpu, then preemption disabled, and
then the STGSC (store guarded storage controls) instruction is
executed.
If the process gets scheduled away between enabling the guarded
storage facility and before preemption is disabled, this might lead to
a special operation exception and therefore kernel crash as soon as
the process is scheduled back and the STGSC instruction is executed.
Fixes: 4e0b1ab72b ("KVM: s390: gs support for kvm guests")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: <stable@vger.kernel.org> # 4.12
Link: https://lore.kernel.org/r/20210415080127.1061275-1-hca@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For the same reason as commit e876f0b69d ("lib/vdso: Allow
architectures to provide the vdso data pointer"), powerpc wants to
avoid calculation of relative position to code.
As the timens_vdso_data is next page to vdso_data, provide
vdso_data pointer to __arch_get_timens_vdso_data() in order
to ease the calculation on powerpc in following patches.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/539c4204b1baa77c55f758904a1ea239abbc7a5c.1617209142.git.christophe.leroy@csgroup.eu
Trigger a warning if any of unwinder tests fail. This should help to
prevent quiet ignoring of test results when panic_on_warn is enabled.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Handle the case of "unwind state reliable but addr is 0" like other error
cases in this function and trigger output of failing stacktrace to aid
debugging.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add arch_ prefix to all atomic operations, and define ARCH_ATOMIC.
This enables KASAN instrumentation for all atomic operations on s390.
This is the s390 variant of commit 8bf705d130 ("locking/atomic/x86:
Switch atomic.h to use atomic-instrumented.h").
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
s390 is the only architecture in the kernel which makes use of gcc's
atomic builtin functions. Even though I don't see any technical
problem with that right now, remove this code and open-code
compare-and-swap loops again, like every other architecture is doing
it also.
We can switch to a generic implementation when other architectures are
doing that also.
See also https://lwn.net/Articles/586838/ for forther details.
This basically reverts commit f318a1229b ("s390/cmpxchg: use
compiler builtins").
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
s390 is the only architecture in the kernel which makes use of gcc's
atomic builtin functions. Even though I don't see any technical
problem with that right now, remove this code and open-code
compare-and-swap loops again, like every other architecture is doing
it also.
We can switch to a generic implementation when other architectures are
doing that also.
See also https://lwn.net/Articles/586838/ for forther details.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use the R,T, and S constraints instead of the Q constraint in atomic
inline assemblies wherever possible. This allows the compiler to
generate better code. (~ -2kb code size).
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Move all remaining inline assemblies from atomic.h to
atomic_ops.h. That way all atomic inline assemblies are
contained within only a single header file.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The bitops code was optimized to generate test under mask instructions
with the __bitops_byte() helper. However that was many years ago and
in the meantime a lot of new instructions were introduced.
Changing the code so that it always operates on longs nowadays even
generates shorter code (~ -20kb, defconfig, gcc 10, march=zE12).
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add conditional trap handlers similar to conditional system calls
(COND_SYSCALL), to reduce the number of ifdefs.
Trap handlers which may or may not exist depending on config options
are supposed to have a COND_TRAP entry, which redirects to
default_trap_handler() for non-existent trap handlers during link
time.
This allows to get rid of the secure execution trap handlers for the
!PGSTE case.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently zpci_configure_device() can be called on a zPCI function in
two completely different states. Either the underlying zPCI function has
already been configured by the platform and we are only doing the
scanning to get it usable by Linux drivers. Or the underlying function
is in Standby and we first do an SCLP to get it configured. This makes
zpci_configure_device() harder to reason about. Since calling
zpci_configure_device() on a function in Standby only happens in
enable_slot() simply pull out the SCLP call and setting of zdev->state
and thus call zpci_configure_device() under the same circumstances as
in the event handling code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Now that the zbus can be created without being scanned we can go one
step further and make registering a device to a zbus independent from
scanning it. This way the zbus handling becomes much more natural
in that functions can be registered on the zbus to be scanned later more
closely resembling the handling of both real PCI hardware and other
virtual PCI busses like Hyper-V's virtual PCI bus (see for example
drivers/pci/controller/pci-hyperv.c:create_root_hv_pci_bus()).
Having zbus registration separate from scanning allows us to return
fully initialized but still disabled zdevs from zpci_create_device()
which can then be configured just as we would configure a zdev from
standby (minus the SCLP Configure already done by the platform). There
is still the exception that a PCI function with non-zero devfn can be
plugged before its PCI bus, which depends on the function with zero
devfn, is created. In this case the zdev returend from
zpci_create_device() is still missing its bus, hotplug slot, and
resources which need to be created later but at least it doesn't wait in
the enabled state and can otherwise be treated as initialized.
With this we also separate the initial PCI scan using CLP List PCI
Functions into two phases. In the CLP loop's callback we only register
each function with a virtual zbus creating the latter as needed. Then,
after we have built this virtual PCI topology based on our list of
zbusses, we can make use of the common code functionality to scan each
complete zbus as a separate child bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In a later change we will first collect all PCI functions from the CLP
List PCI functions call, then register them to/creating the relevant
zbus. Then only after we've created our virtual bus structure will we
scan all zbusses iterating over the zbus list. Since scanning is
relatively slow a spinlock is a bad fit for protecting the
loop over the devices on the zbus. Furthermore doing the probing on the
bus we need to use pci_lock_rescan_remove() as devices are added to
the PCI subsystem and that is a mutex which can't be locked nested
inside a spinlock section. Note that the contention of this lock should
be very low either way as zbusses are only added/removed concurrently on
hotplug events.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In the existing code the creation of the PCI bus and the scanning of
function zero all happens in zpci_scan_bus(). This in turn requires
functions to be enabled and their resources to be available before the
PCI bus is even created.
This not only means that functions are enabled long before they are
actually made available to the common PCI subsystem. In case of
functions with non-zero devfn which appeared before the function with
devfn zero they can wait arbitrarily long in this enabled but not
scanned state.
Fix this by separating the creation of the PCI bus from scanning it and
only prepare, that is enable and setup MMIO bus resources, functions
just before they are scanned. As they may be scanned multiple times
track if we already created resources in the zdev.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Pull setting the maximum bus speed and multifunction attribute into
zpci_bus_scan() in preparation for handling bus creation separately
from scanning the bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
To match zpci_bus_scan_device() and the PCI common code terminology and
to remove some code duplication, we pull the multiple uses of
pci_scan_single_device() into a function. For now this has the side
effect of adding each device to the PCI bus separately and locking and
unlocking the rescan/remove lock for each instead of just once per bus.
This is clearly less efficient but provides a correct intermediate
behavior until a follow on change does both the adding and scanning only
once per bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Convert the program check table to C. Which allows to get rid of yet
another assembler file, and also enables proper type checking for the
table.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baisong Zhong <zhongbaisong@huawei.com>
Fixes: 37564ed834 ("s390/uv: add prot virt guest/host indication files")
Link: https://lore.kernel.org/r/2f7d62a4-3e75-b2b4-951b-75ef8ef59d16@huawei.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
* fixes:
s390/entry: save the caller of psw_idle
s390/entry: avoid setting up backchain in ext|io handlers
s390/setup: use memblock_free_late() to free old stack
s390/irq: fix reading of ext_params2 field from lowcore
s390/unwind: add machine check handler stack
s390/cpcmd: fix inline assembly register clobbering
MAINTAINERS: add backups for s390 vfio drivers
s390/vdso: fix initializing and updating of vdso_data
s390/vdso: fix tod_steering_delta type
s390/vdso: copy tod_steering_delta value to vdso_data page
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently psw_idle does not allocate a stack frame and does not
save its r14 and r15 into the save area. Even though this is valid from
call ABI point of view, because psw_idle does not make any calls
explicitly, in reality psw_idle is an entry point for controlled
transition into serving interrupts. So, in practice, psw_idle stack
frame is analyzed during stack unwinding. Depending on build options
that r14 slot in the save area of psw_idle might either contain a value
saved by previous sibling call or complete garbage.
[task 0000038000003c28] do_ext_irq+0xd6/0x160
[task 0000038000003c78] ext_int_handler+0xba/0xe8
[task *0000038000003dd8] psw_idle_exit+0x0/0x8 <-- pt_regs
([task 0000038000003dd8] 0x0)
[task 0000038000003e10] default_idle_call+0x42/0x148
[task 0000038000003e30] do_idle+0xce/0x160
[task 0000038000003e70] cpu_startup_entry+0x36/0x40
[task 0000038000003ea0] arch_call_rest_init+0x76/0x80
So, to make a stacktrace nicer and actually point for the real caller of
psw_idle in this frequently occurring case, make psw_idle save its r14.
[task 0000038000003c28] do_ext_irq+0xd6/0x160
[task 0000038000003c78] ext_int_handler+0xba/0xe8
[task *0000038000003dd8] psw_idle_exit+0x0/0x6 <-- pt_regs
([task 0000038000003dd8] arch_cpu_idle+0x3c/0xd0)
[task 0000038000003e10] default_idle_call+0x42/0x148
[task 0000038000003e30] do_idle+0xce/0x160
[task 0000038000003e70] cpu_startup_entry+0x36/0x40
[task 0000038000003ea0] arch_call_rest_init+0x76/0x80
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently when interrupt arrives to cpu while in kernel context
INT_HANDLER macro (used for ext_int_handler and io_int_handler)
allocates new stack frame and pt_regs on the kernel stack and
sets up the backchain to jump over the pt_regs to the frame which has
been interrupted. This is not ideal to two reasons:
1. This hides the fact that kernel stack contains interrupt frame in it
and hence breaks arch_stack_walk_reliable(), which needs to know that to
guarantee "reliability" and checks that there are no pt_regs on the way.
2. It breaks the backchain unwinder logic, which assumes that the next
stack frame after an interrupt frame is reliable, while it is not.
In some cases (when r14 contains garbage) this leads to early unwinding
termination with an error, instead of marking frame as unreliable
and continuing.
To address that, only set backchain to 0.
Fixes: 56e62a7370 ("s390: convert to generic entry")
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use memblock_free_late() to free the old machine check stack to the
buddy allocator instead of leaking it.
Fixes: b61b159512 ("s390: add stack for machine check handler")
Cc: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Due to historical reasons mark_kernel_pXd() functions
misuse the notion of physical vs virtual addresses
difference.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
struct ccw1 is declared twice. One has been declared
at 21st line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Acked-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
On s390 each PCI device has a user-defined ID (UID) exposed under
/sys/bus/pci/devices/<dev>/uid. This ID was designed to serve as the PCI
device's primary index and to match the device within Linux to the
device configured in the hypervisor. To serve as a primary identifier
the UID must be unique within the Linux instance, this is guaranteed by
the platform if and only if the UID Uniqueness Checking flag is set
within the CLP List PCI Functions response.
While the UID has been exposed to userspace since commit ac4995b9d5
("s390/pci: add some new arch specific pci attributes") whether or not
the platform guarantees its uniqueness for the lifetime of the Linux
instance while defined is not visible from userspace. Remedy this by
exposing this as a per device attribute at
/sys/bus/pci/devices/<dev>/uid_is_unique
Keeping this a per device attribute allows for maximum flexibility if we
ever end up with some devices not having a UID or not enjoying the
guaranteed uniqueness.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In commit dee60c0dbc ("s390/pci: add zpci_event_hard_deconfigured()")
we added a zdev_enabled() check to what was previously an uncoditional
call to zpci_disable_device(). There are two problems with that. Firstly
zpci_had_deconfigured() is only called on event 0x0304 for which the
device is always already disabled by the platform so it is always false.
Secondly zpci_disable_device() not only disables the device but also
calls zpci_dma_exit_device() which is thus not called and we leak the
DMA tables.
Fix this by calling zpci_disable_device() unconditionally to perform
Linux side cleanup including the freeing of DMA tables.
Fixes: dee60c0dbc ("s390/pci: add zpci_event_hard_deconfigured()")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Wang reported that clock_gettime(CLOCK_MONOTONIC_RAW, ...) returns
incorrect values when time is provided via vdso instead of system call:
vdso_ts_nsec = 4484351380985507, vdso_ts.tv_sec = 4484351, vdso_ts.tv_nsec = 380985507
sys_ts_nsec = 1446923235377, sys_ts.tv_sec = 1446, sys_ts.tv_nsec = 923235377
Within the s390 specific vdso function __arch_get_hw_counter() reads
tod clock steering values from the arch_data member of the passed in
vdso_data structure.
Problem is that only for the CS_HRES_COARSE vdso_data arch_data is
initialized and gets updated. The CS_RAW specific vdso_data does not
contain any valid tod_clock_steering information, which explains the
different values.
Fix this by initializing and updating all vdso_datas.
Reported-by: Li Wang <liwang@redhat.com>
Tested-by: Li Wang <liwang@redhat.com>
Fixes: 1ba2d6c0fd ("s390/vdso: simplify __arch_get_hw_counter()")
Link: https://lore.kernel.org/linux-s390/YFnxr1ZlMIOIqjfq@osiris
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The s390 specific vdso function __arch_get_hw_counter() is supposed to
consider tod clock steering.
If a tod clock steering event happens and the tod clock is set to a
new value __arch_get_hw_counter() will not return the real tod clock
value but slowly drift it from the old delta until the returned value
finally matches the real tod clock value again.
Unfortunately the type of tod_steering_delta unsigned while it is
supposed to be signed. It depends on if tod_steering_delta is negative
or positive in which direction the vdso code drifts the clock value.
Worst case is now that instead of drifting the clock slowly it will
jump into the opposite direction by a factor of two.
Fix this by simply making tod_steering_delta signed.
Fixes: 4bff8cb545 ("s390: convert to GENERIC_VDSO")
Cc: <stable@vger.kernel.org> # 5.10
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
When converting the vdso assembler code to C it was forgotten to
actually copy the tod_steering_delta value to vdso_data page.
Which in turn means that tod clock steering will not work correctly.
Fix this by simply copying the value whenever it is updated.
Fixes: 4bff8cb545 ("s390: convert to GENERIC_VDSO")
Cc: <stable@vger.kernel.org> # 5.10
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
prot_virt_host is only available if CONFIG_KVM is enabled. So lets use
a variable initialized to zero and overwrite it when that config
option is set with prot_virt_host.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Fixes: 37564ed834 ("s390/uv: add prot virt guest/host indication files")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Prefixing needs to be applied to the guest real address to translate it
into a guest absolute address.
The value of MSO needs to be added to a guest-absolute address in order to
obtain the host-virtual.
Fixes: bdf7509bbe ("s390/kvm: VSIE: correctly handle MVPG when in VSIE")
Reported-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210322140559.500716-3-imbrenda@linux.ibm.com
[borntraeger@de.ibm.com simplify mso]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
A new function _kvm_s390_real_to_abs will apply prefixing to a real address
with a given prefix value.
The old kvm_s390_real_to_abs becomes now a wrapper around the new function.
This is needed to avoid code duplication in vSIE.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210322140559.500716-2-imbrenda@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Extend kvm_s390_shadow_fault to return the pointer to the valid leaf
DAT table entry, or to the invalid entry.
Also return some flags in the lower bits of the address:
PEI_DAT_PROT: indicates that DAT protection applies because of the
protection bit in the segment (or, if EDAT, region) tables.
PEI_NOT_PTE: indicates that the address of the DAT table entry returned
does not refer to a PTE, but to a segment or region table.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: stable@vger.kernel.org
Reviewed-by: Janosch Frank <frankja@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20210302174443.514363-3-imbrenda@linux.ibm.com
[borntraeger@de.ibm.com: fold in a fix from Claudio]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We are spending way too much effort on qdio-internal bookkeeping for
QAOB management & caching, and it's still not robust. Once qdio's
TX path has detached the QAOB from a PENDING buffer, we lost all
track of it until it shows up in a CQ notification again. So if the
device is torn down before that notification arrives, we leak the QAOB.
Just have the driver take care of it, and simply pass down a QAOB if
they want a TX with async-completion capability. For a buffer in PENDING
state that requires the QAOB for final completion, qeth can now also try
to recycle the buffer's QAOB rather than unconditionally freeing it.
This also eliminates the qdio_outbuf_state array, which was only needed
to transfer the aob->user1 tag from the driver to the qdio layer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The zpci_remove_device() function removes the device from the PCI common
code core which is an operation dealing primarily with the zbus and PCI
bus code. With that and to match an upcoming refactoring of the
symmetric scanning part move it to the bus code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
A zPCI event with PEC 0x0301 for an existing zPCI device goes through
the same actions as enable_slot(). Similarly a zPCI event with PEC
0x0303 does the same steps as disable_slot().
We can thus unify both actions as zpci_configure_device() respectively
zpci_deconfigure_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This patch introduces the mechanism to inject artificial events to the
CIO layer.
One of the main-event type which triggers the CommonIO operations are
Channel Report events. When a malfunction or other condition affecting
channel-subsystem operation is recognized, a Channel Report Word
(consisting of one or more CRWs) describing the condition is made
pending for retrieval and analysis by the program. The CRW contains
information concerning the identity and state of a facility following
the detection of the malfunction or other condition.
The patch introduces two debugfs interfaces which can be used to inject
'artificial' events from the userspace. It is intended to provide an easy
means to increase the test coverage for CIO code. And this functionality
can be enabled via a new configuration option CONFIG_CIO_INJECT.
The newly introduces debugfs interfaces can be used as mentioned below
to generate different fake-events. To use the crw_inject, first we should
enable it by using enable_inject interface.
i.e
echo 1 > /sys/kernel/debug/s390/cio/enable_inject
After the first step, user can simulate CRW as follows:
echo <solicited> <overflow> <chaining> <rsc> <ancillary> <erc> <rsid> \
> /sys/kernel/debug/s390/cio/crw_inject
Example:
A permanent error ERC on CHPID 0x60 would look like this:
echo 0 0 0 4 0 6 0x60 > /sys/kernel/debug/s390/cio/crw_inject
and an initialized ERC on the same CHPID:
echo 0 0 0 4 0 2 0x60 > /sys/kernel/debug/s390/cio/crw_inject
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens