* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
Enables Auto-CMD23 support where available (SDHCI 3.0 controllers)
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Tested-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards operating at UHS104 or better support SET_BLOCK_COUNT.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Supply a link to TMIO private data for platforms to implement their
own card detection.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there is only 1 function interrupt registered it is possible to
improve performance by directly calling the irq handler and avoiding
the overhead of reading the CCCR registers.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 can support retuning modes 1,2 or 3 depending on
the bits 46-47 of the Capabilities register. Also, the timer count for
retuning is indicated by bits 40-43 of the same register. We initialize
timer_list for retuning the first time we execute tuning procedure. This
condition is indicated by SDHCI_NEEDS_RETUNING not being set. Since
retuning mode 1 sets a limit of 4MB on the maximum data length, we set
max_blk_count appropriately. Once the tuning timer expires, we set
SDHCI_NEEDS_RETUNING flag, and if the flag is set, we execute tuning
procedure before sending the next command. We need to restore mmc_request
structure after executing retuning procedure since host->mrq is used
inside the procedure to send CMD19. We also disable and re-enable this
flag during suspend and resume respectively, as per the spec v3.00.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 supports programmable clock mode as an optional
feature. The support for this mode is indicated by non-zero value in
bits 48-55 of the Capabilities register. If supported, the actual
value of Clock Multiplier is one more than the value provided in the
bit fields. We only set Clock Generator Select (bit 5) and SDCLK
Frequency Select (bits 8-15) of the Clock Control register in case
Preset Value Enable is not set, otherwise these fields are automatically
set by the Host Controller based on the UHS mode selected. Also, since
the maximum and minimum clock frequency in this mode can be
(Base Clock * Clock Mul) and (Base Clock * Clock Mul)/1024 respectively,
f_max and f_min have been recalculated to reflect this change.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the Host Controller spec v3.00, setting Preset Value Enable
in the Host Control2 register lets SDCLK Frequency Select, Clock Generator
Select and Driver Strength Select to be set automatically by the Host
Controller based on the UHS-I mode set. This patch enables this feature.
Since Preset Value Enable makes sense only for UHS-I cards, we enable this
feature after successfull UHS-I initialization. We also reset Preset Value
Enable next time before initialization.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.
We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since only UHS-I cards respond with S18A set in response to ACMD41,
we set the card as ultra-high-speed after successfull initialization.
We need to decide whether a card is SDXC based on the C_SIZE field
of CSDv2.0 register. According to Physical Layer spec v3.01, the
minimum value of C_SIZE for SDXC card is 00FFFFh.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We decide on the current limit to be set for the card based on the
Capability of Host Controller to provide current at 1.8V signalling,
and the maximum current limit of the card as indicated by CMD6
mode 0. We then set the current limit for the card using CMD6 mode 1.
As per the Physical Layer Spec v3.01, the current limit switch is
only applicable for SDR50, SDR104, and DDR50 bus speed modes. For
other UHS-I modes, we set the default current limit of 200mA.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards which conform to Physical Layer Spec v3.01 can support
additional Bus Speed Modes, Driver Strength, and Current Limit
other than the default values. We use CMD6 mode 0 to read these
additional card functions. The values read here will be used
during UHS-I initialization steps.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows appropriately-privileged applications to send CMD (normal) and ACMD
(application-specific; preceded with CMD55) commands to cards/devices on
the mmc bus. This is primarily useful for enabling the security
functionality built in to every SD card.
It can also be used as a generic passthrough (e.g. to enable virtual
machines to control mmc bus devices directly). However, this use case has
not been tested rigorously. Generic passthrough testing was only conducted
for a few non-security opcodes to prove the feasibility of the passthrough.
Since any opcode can be sent using this passthrough, it is very possible to
render the card/device unusable. Applications that use this ioctl must
have CAP_SYS_RAWIO.
Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC,
TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC.
Signed-off-by: John Calixto <john.calixto@modsystems.com>
Reviewed-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
On HP laptops with JMicron 388 chip, the write-locked SD card isn't
detected correctly as read-only in many cases. This is because the
PRESENT_STATE register becomes unsable just after plugging, and it
returns the WRITE_PROTECT bit wrongly at the first read.
This patch fixes the read-only detection by adding a new sdhci quirk
indicating to check the register more intensively with a relatively
long delay.
The patch is tested with 2.6.39-rc4 kernel.
Cc: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows device MMC boot partitions to be accessed. MMC partitions are
treated effectively as separate block devices on the same MMC card.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command.
First step to making host honor timeouts for non-data-transfer
commands. Cleans up erase timeout code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix data truncation warnings: .manfid is not unsigned long:
drivers/mmc/core/quirks.c:36: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:40: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:43: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:46: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up
resistor on CD/DAT[3] (pin 1) of the card.
Make it possible to start using sdio_disable_cd() by introducing
MMC_QUIRK_DISABLE_CD.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function
interface code" as indicated by the card's FBR, and instead treat all
functions as non-standard interfaces.
This is required to prevent standard drivers from facing
errors when trying to communicate with SDIO cards that erroneously
indicate standard function interface codes.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
6b5eda36 followed SDIO spec part E1 section 8, which states that
in case SDIO interrupts are being used to wake up a suspended host,
then it is required to switch to 1-bit mode before stopping the clock.
Before switching to 1-bit mode (or back to 4-bit mode on resume),
make sure that SDIO interrupts are really being used to wake the host.
This is helpful for devices which have an external irq line (e.g.
wl1271), and do not use SDIO interrupts to wake up the host.
In this case, switching to 1-bit mode (and back to 4-bit mode on resume)
is not necessary.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_card_is_powered_resumed is a mouthful; instead, simply use
mmc_card_keep_power, which also better explains the purpose of
the macro.
Employ mmc_card_keep_power() where possible.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bruce Clemens <bpclemens@marvell.com>
Signed-off-by: Mark F. Brown <markb@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently there is a race in the MMC core between a card-detect
rescan work and the clock-gating work, scheduled from a command
completion. Fix it by removing the dedicated clock-gating mutex
and using the MMC standard locking mechanism instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Also add TMIO_BBS.
This allows these defines to also be used by zboot.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is my second attempt to make this enum generally available.
The first attempt added MMCIF_PROGRESS_* to include/linux/mmc/sh_mmcif.h.
However this is not sufficiently generic as the enum will be
used by SDHI boot code.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for power regulators.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is related to re-init processing on suspend/resume.
When card is resuming, some register is reset. If card is removable,
maybe controller should be rescan for card. But if assume card is
non-removable, need to restore the old value at registers.
We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds quirks and capabilities to platdata.
Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we need some quirks, maybe add quirks in future
But now, quirks value set to integer..later we should be confused..
So I think that need bit-shift control.
And If we need not any quirks, we didn't set anything..
(Need not DW_MCI_QUIRK_NONE)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.
To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.
So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk. We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.
The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.
Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using the I/O accessors in raw mode from the boot stubs we don't
want to bother with any of the complexity associated with readl/writel
and friends. Furthermore, utilization within the context of the host
driver itself is all performed on an ioremapped window, so using the
__raw variants there doesn't pose any problem either.
If and when barriers need to be added in the future, these will need to
be explicitly written out, but this is so far not a concern for any of
the affected CPUs in question.
This fixes up the link error introduced by the ARM tree via its barrier
refactoring:
arch/arm/boot/compressed/mmcif-sh7372.o: In function `mmcif_loader':
mmcif-sh7372.c:(.text+0x9e8): undefined reference to `outer_cache
Following the change in:
http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=6275/1
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds