This patch is to remove the typedef sctp_ipv6addr_param_t, and replace
with struct sctp_ipv6addr_param in the places where it's using this
typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if there are several same route entries with different outgoing net device,
application's socket specifies the oif through setsockopt with
SO_BINDTODEVICE, sctpv6 should choose the route entry whose outgoing net
device is the oif which was specified by socket, set the value of
flowi6_oif to sk->sk_bound_dev_if to make sctp_v6_get_dst to find the
correct route entry.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP needs fixes similar to 83eaddab43 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ca50d12fe ("sctp: fix src address selection if using secondary
addresses") has fixed a src address selection issue when using secondary
addresses for ipv4.
Now sctp ipv6 also has the similar issue. When using a secondary address,
sctp_v6_get_dst tries to choose the saddr which has the most same bits
with the daddr by sctp_v6_addr_match_len. It may make some cases not work
as expected.
hostA:
[1] fd21:356b:459a:cf10::11 (eth1)
[2] fd21:356b:459a:cf20::11 (eth2)
hostB:
[a] fd21:356b:459a:cf30::2 (eth1)
[b] fd21:356b:459a:cf40::2 (eth2)
route from hostA to hostB:
fd21:356b:459a:cf30::/64 dev eth1 metric 1024 mtu 1500
The expected path should be:
fd21:356b:459a:cf10::11 <-> fd21:356b:459a:cf30::2
But addr[2] matches addr[a] more bits than addr[1] does, according to
sctp_v6_addr_match_len. It causes the path to be:
fd21:356b:459a:cf20::11 <-> fd21:356b:459a:cf30::2
This patch is to fix it with the same way as Marcelo's fix for sctp ipv4.
As no ip_dev_find for ipv6, this patch is to use ipv6_chk_addr to check
if the saddr is in a dev instead.
Note that for backwards compatibility, it will still do the addr_match_len
check here when no optimal is found.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prior to this patch, in rx path, before calling lock_sock, it needed to
hold assoc when got it by __sctp_lookup_association, in case other place
would free/put assoc.
But in __sctp_lookup_association, it lookup and hold transport, then got
assoc by transport->assoc, then hold assoc and put transport. It means
it didn't hold transport, yet it was returned and later on directly
assigned to chunk->transport.
Without the protection of sock lock, the transport may be freed/put by
other places, which would cause a use-after-free issue.
This patch is to fix this issue by holding transport instead of assoc.
As holding transport can make sure to access assoc is also safe, and
actually it looks up assoc by searching transport rhashtable, to hold
transport here makes more sense.
Note that the function will be renamed later on on another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 486bdee013 ("sctp: add support for RPS and RFS")
saves skb->hash into sk->sk_rxhash so that the inet_* can
record it to flow table.
But sctp uses sock_common_recvmsg as .recvmsg instead
of inet_recvmsg, sock_common_recvmsg doesn't invoke
sock_rps_record_flow to record the flow. It may cause
that the receiver has no chances to record the flow if
it doesn't send msg or poll the socket.
So this patch fixes it by using inet_recvmsg as .recvmsg
in sctp.
Fixes: 486bdee013 ("sctp: add support for RPS and RFS")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sctp support ipv6 nonlocal bind by adding
sp->inet.freebind and net->ipv6.sysctl.ip_nonlocal_bind
check in sctp_v6_available as what sctp did to support
ipv4 nonlocal bind (commit cdac4e0774).
Reported-by: Shijoe George <spanjikk@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP will try to access original IP headers on sctp_recvmsg in order to
copy the addresses used. There are also other places that do similar access
to IP or even SCTP headers. But after 90017accff ("sctp: Add GSO
support") they aren't always there because they are only present in the
header skb.
SCTP handles the queueing of incoming data by cloning the incoming skb
and limiting to only the relevant payload. This clone has its cb updated
to something different and it's then queued on socket rx queue. Thus we
need to fix this in two moments.
For rx path, not related to socket queue yet, this patch uses a
partially copied sctp_input_cb to such GSO frags. This restores the
ability to access the headers for this part of the code.
Regarding the socket rx queue, it removes iif member from sctp_event and
also add a chunk pointer on it.
With these changes we're always able to reach the headers again.
The biggest change here is that now the sctp_chunk struct and the
original skb are only freed after the application consumed the buffer.
Note however that the original payload was already like this due to the
skb cloning.
For iif, SCTP's IPv4 code doesn't use it, so no change is necessary.
IPv6 now can fetch it directly from original's IPv6 CB as the original
skb is still accessible.
In the future we probably can simplify sctp_v*_skb_iif() stuff, as
sctp_v4_skb_iif() was called but it's return value not used, and now
it's not even called, but such cleanup is out of scope for this change.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP6_INC_STATS_BH() to __ICMP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP is lacking proper np->opt cloning at accept() time.
TCP and DCCP use ipv6_dup_options() helper, do the same
in SCTP.
We might later factorize this code in a common helper to avoid
future mistakes.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cooking the sctp np->opt rcu fixes, I forgot to move
one rcu_read_unlock() after the added rcu_dereference() in
sctp_v6_get_dst()
This gave lockdep warnings reported by Dave Jones.
Fixes: c836a8ba93 ("ipv6: sctp: add rcu protection around np->opt")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes the work I did in commit 45f6fad84c
("ipv6: add complete rcu protection around np->opt"), as I missed
sctp part.
This simply makes sure np->opt is used with proper RCU locking
and accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie. Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address. The dst and src can be recovered from
the calling site.
We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changing how struct net is refcounted
on kernel sockets pass the knowledge that we are creating
a kernel socket from sock_create_kern through to sk_alloc.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP socket extensions API document describes the v4mapping option as
follows:
8.1.15. Set/Clear IPv4 Mapped Addresses (SCTP_I_WANT_MAPPED_V4_ADDR)
This socket option is a Boolean flag which turns on or off the
mapping of IPv4 addresses. If this option is turned on, then IPv4
addresses will be mapped to V6 representation. If this option is
turned off, then no mapping will be done of V4 addresses and a user
will receive both PF_INET6 and PF_INET type addresses on the socket.
See [RFC3542] for more details on mapped V6 addresses.
This description isn't really in line with what the code does though.
Introduce addr_to_user (renamed addr_v4map), which should be called
before any sockaddr is passed back to user space. The new function
places the sockaddr into the correct format depending on the
SCTP_I_WANT_MAPPED_V4_ADDR option.
Audit all places that touched v4mapped and either sanely construct
a v4 or v6 address then call addr_to_user, or drop the
unnecessary v4mapped check entirely.
Audit all places that call addr_to_user and verify they are on a sycall
return path.
Add a custom getname that formats the address properly.
Several bugs are addressed:
- SCTP_I_WANT_MAPPED_V4_ADDR=0 often returned garbage for
addresses to user space
- The addr_len returned from recvmsg was not correct when
returning AF_INET on a v6 socket
- flowlabel and scope_id were not zerod when promoting
a v4 to v6
- Some syscalls like bind and connect behaved differently
depending on v4mapped
Tested bind, getpeername, getsockname, connect, and recvmsg for proper
behaviour in v4mapped = 1 and 0 cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit efe4208f47f907b86f528788da711e8ab9dea44d:
'ipv6: make lookups simpler and faster' broke initialization of local source
address on accepted ipv6 sockets. Before the mentioned commit receive address
was copied along with the contents of ipv6_pinfo in sctp_v6_create_accept_sk.
Now when it is moved, it has to be copied separately.
This also fixes lksctp's ipv6 regression in a sense that test_getname_v6, TC5 -
'getsockname on a connected server socket' now passes.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors while the space is required or prohibited
to the "=,()++..."
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 93b36cf342 ("ipv6: support IPV6_PMTU_INTERFACE on sockets")
I made a horrible mistake to add ip6_sk_accept_pmtu to the generic
sctp_icmp_frag_needed path. This results in build warnings if IPv6 is
disabled which were luckily caught by Fengguang's kbuild bot. But it
also leads to a kernel panic IPv4 frag-needed packet is received.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FLOWI_FLAG_CAN_SLEEP was used to notify xfrm about the posibility
to sleep until the needed states are resolved. This code is gone,
so FLOWI_FLAG_CAN_SLEEP is not needed anymore.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8a07eb0a50 ("sctp: Add ASCONF operation on the single-homed host")
implemented possible use of IPv4 addresses with non SCTP_ADDR_SRC state
as source address when sending ASCONF (ADD) packets, but IPv6 part for
that was not implemented in 8a07eb0a50. Therefore, as this is not restricted
to IPv4-only, fix this up to allow the same for IPv6 addresses in SCTP.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Michio Honda <micchie@sfc.wide.ad.jp>
Acked-by: Michio Honda <micchie@sfc.wide.ad.jp>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP listener refactoring, part 4 :
To speed up inet lookups, we moved IPv4 addresses from inet to struct
sock_common
Now is time to do the same for IPv6, because it permits us to have fast
lookups for all kind of sockets, including upcoming SYN_RECV.
Getting IPv6 addresses in TCP lookups currently requires two extra cache
lines, plus a dereference (and memory stall).
inet6_sk(sk) does the dereference of inet_sk(__sk)->pinet6
This patch is way bigger than its IPv4 counter part, because for IPv4,
we could add aliases (inet_daddr, inet_rcv_saddr), while on IPv6,
it's not doable easily.
inet6_sk(sk)->daddr becomes sk->sk_v6_daddr
inet6_sk(sk)->rcv_saddr becomes sk->sk_v6_rcv_saddr
And timewait socket also have tw->tw_v6_daddr & tw->tw_v6_rcv_saddr
at the same offset.
We get rid of INET6_TW_MATCH() as INET6_MATCH() is now the generic
macro.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Chester reported an issue with IPv6 on SCTP that IPsec traffic is not
being encrypted, whereas on IPv4 it is. Setting up an AH + ESP transport
does not seem to have the desired effect:
SCTP + IPv4:
22:14:20.809645 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 116)
192.168.0.2 > 192.168.0.5: AH(spi=0x00000042,sumlen=16,seq=0x1): ESP(spi=0x00000044,seq=0x1), length 72
22:14:20.813270 IP (tos 0x2,ECT(0), ttl 64, id 0, offset 0, flags [DF], proto AH (51), length 340)
192.168.0.5 > 192.168.0.2: AH(spi=0x00000043,sumlen=16,seq=0x1):
SCTP + IPv6:
22:31:19.215029 IP6 (class 0x02, hlim 64, next-header SCTP (132) payload length: 364)
fe80::222:15ff:fe87:7fc.3333 > fe80::92e6:baff:fe0d:5a54.36767: sctp
1) [INIT ACK] [init tag: 747759530] [rwnd: 62464] [OS: 10] [MIS: 10]
Moreover, Alan says:
This problem was seen with both Racoon and Racoon2. Other people have seen
this with OpenSwan. When IPsec is configured to encrypt all upper layer
protocols the SCTP connection does not initialize. After using Wireshark to
follow packets, this is because the SCTP packet leaves Box A unencrypted and
Box B believes all upper layer protocols are to be encrypted so it drops
this packet, causing the SCTP connection to fail to initialize. When IPsec
is configured to encrypt just SCTP, the SCTP packets are observed unencrypted.
In fact, using `socat sctp6-listen:3333 -` on one end and transferring "plaintext"
string on the other end, results in cleartext on the wire where SCTP eventually
does not report any errors, thus in the latter case that Alan reports, the
non-paranoid user might think he's communicating over an encrypted transport on
SCTP although he's not (tcpdump ... -X):
...
0x0030: 5d70 8e1a 0003 001a 177d eb6c 0000 0000 ]p.......}.l....
0x0040: 0000 0000 706c 6169 6e74 6578 740a 0000 ....plaintext...
Only in /proc/net/xfrm_stat we can see XfrmInTmplMismatch increasing on the
receiver side. Initial follow-up analysis from Alan's bug report was done by
Alexey Dobriyan. Also thanks to Vlad Yasevich for feedback on this.
SCTP has its own implementation of sctp_v6_xmit() not calling inet6_csk_xmit().
This has the implication that it probably never really got updated along with
changes in inet6_csk_xmit() and therefore does not seem to invoke xfrm handlers.
SCTP's IPv4 xmit however, properly calls ip_queue_xmit() to do the work. Since
a call to inet6_csk_xmit() would solve this problem, but result in unecessary
route lookups, let us just use the cached flowi6 instead that we got through
sctp_v6_get_dst(). Since all SCTP packets are being sent through sctp_packet_transmit(),
we do the route lookup / flow caching in sctp_transport_route(), hold it in
tp->dst and skb_dst_set() right after that. If we would alter fl6->daddr in
sctp_v6_xmit() to np->opt->srcrt, we possibly could run into the same effect
of not having xfrm layer pick it up, hence, use fl6_update_dst() in sctp_v6_get_dst()
instead to get the correct source routed dst entry, which we assign to the skb.
Also source address routing example from 625034113 ("sctp: fix sctp to work with
ipv6 source address routing") still works with this patch! Nevertheless, in RFC5095
it is actually 'recommended' to not use that anyway due to traffic amplification [1].
So it seems we're not supposed to do that anyway in sctp_v6_xmit(). Moreover, if
we overwrite the flow destination here, the lower IPv6 layer will be unable to
put the correct destination address into IP header, as routing header is added in
ipv6_push_nfrag_opts() but then probably with wrong final destination. Things aside,
result of this patch is that we do not have any XfrmInTmplMismatch increase plus on
the wire with this patch it now looks like:
SCTP + IPv6:
08:17:47.074080 IP6 2620:52:0:102f:7a2b:cbff:fe27:1b0a > 2620:52:0:102f:213:72ff:fe32:7eba:
AH(spi=0x00005fb4,seq=0x1): ESP(spi=0x00005fb5,seq=0x1), length 72
08:17:47.074264 IP6 2620:52:0:102f:213:72ff:fe32:7eba > 2620:52:0:102f:7a2b:cbff:fe27:1b0a:
AH(spi=0x00003d54,seq=0x1): ESP(spi=0x00003d55,seq=0x1), length 296
This fixes Kernel Bugzilla 24412. This security issue seems to be present since
2.6.18 kernels. Lets just hope some big passive adversary in the wild didn't have
its fun with that. lksctp-tools IPv6 regression test suite passes as well with
this patch.
[1] http://www.secdev.org/conf/IPv6_RH_security-csw07.pdf
Reported-by: Alan Chester <alan.chester@tekelec.com>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sctp sits on IPv6, sctp_transport_dst_check pass cookie as ZERO,
as a result ip6_dst_check always fail out. This behaviour makes
transport->dst useless, because every sctp_packet_transmit must look
for valid dst.
Add a dst_cookie into sctp_transport, and set the cookie whenever we
get new dst for sctp_transport. So dst validness could be checked
against it.
Since I have split genid for IPv4 and IPv6, also delete/add IPv6 address
will also bump IPv6 genid. So issues we discussed in:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4
have all been sloved for this patch.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get rid of all own SCTP debug printk macros and use the ones
that the kernel offers anyway instead. This makes the code more readable
and conform to the kernel code, and offers all the features of dynamic
debbuging that pr_debug() et al has, such as only turning on/off portions
of debug messages at runtime through debugfs. The runtime cost of having
CONFIG_DYNAMIC_DEBUG enabled, but none of the debug statements printing,
is negligible [1]. If kernel debugging is completly turned off, then these
statements will also compile into "empty" functions.
While we're at it, we also need to change the Kconfig option as it /now/
only refers to the ifdef'ed code portions in outqueue.c that enable further
debugging/tracing of SCTP transaction fields. Also, since SCTP_ASSERT code
was enabled with this Kconfig option and has now been removed, we
transform those code parts into WARNs resp. where appropriate BUG_ONs so
that those bugs can be more easily detected as probably not many people
have SCTP debugging permanently turned on.
To turn on all SCTP debugging, the following steps are needed:
# mount -t debugfs none /sys/kernel/debug
# echo -n 'module sctp +p' > /sys/kernel/debug/dynamic_debug/control
This can be done more fine-grained on a per file, per line basis and others
as described in [2].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-39-46.pdf
[2] Documentation/dynamic-debug-howto.txt
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_STATIC is just another define for the static keyword. It's use
is inconsistent in the SCTP code anyway and it was introduced in the
initial implementation of SCTP in 2.5. We have a regression suite in
lksctp-tools, but this is for user space only, so noone makes use of
this macro anymore. The kernel test suite for 2.5 is incompatible with
the current SCTP code anyway.
So simply Remove it, to be more consistent with the rest of the kernel
code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t_new rather obfuscates things where everyone else is using actual
function names instead of that macro, so replace it with kzalloc,
which is the function t_new wraps.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects an byte order conflict introduced by
158874cac6
("sctp: Correct access to skb->{network, transport}_header").
The values in question are host byte order.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case sk_buff_data_t will be a pointer, however,
skb->{network,transport}_header is now __u16.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We walk through the bind address list and try to get the best source
address for a given destination. However, currently, we take the
'continue' path of the loop when an entry is invalid (!laddr->valid)
*and* the entry state does not equal SCTP_ADDR_SRC (laddr->state !=
SCTP_ADDR_SRC).
Thus, still, invalid entries with SCTP_ADDR_SRC might not 'continue'
as well as valid entries with SCTP_ADDR_{NEW, SRC, DEL}, with a possible
false baddr and matchlen as a result, causing in worst case dst route
to be false or possibly NULL.
This test should actually be a '||' instead of '&&'. But lets fix it
and make this a bit easier to read by having the condition the same way
as similarly done in sctp_v4_get_dst.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix the sctp_af operations to work in all namespaces
- Enable sctp socket creation in all network namespaces.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move the address lists into struct net
- Add per network namespace initialization and cleanup
- Pass around struct net so it is everywhere I need it.
- Rename all of the global variable references into references
to the variables moved into struct net
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use struct net in the hash calculation
- Use sock_net(association.base.sk) in the association lookups.
- On receive calculate the network namespace from skb->dev.
- Pass struct net from receive down to the functions that actually
do the association lookup.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C assignment can handle struct in6_addr copying.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 66b13d99d9 (ipv4: tcp: fix TOS value in ACK messages sent from
TIME_WAIT) fixed IPv4 only.
This part is for the IPv6 side, adding a tclass param to ip6_xmit()
We alias tw_tclass and tw_tos, if socket family is INET6.
[ if sockets is ipv4-mapped, only IP_TOS socket option is used to fill
TOS field, TCLASS is not taken into account ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP reconfigure the IP addresses in the association by using
ASCONF chunks as mentioned in RFC5061. For example, we can
start to use the newly configured IP address in the existing
association. This patch implements automatic ASCONF operation
in the SCTP stack with address events in the host computer,
which is called auto_asconf.
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
The rcu callback sctp_local_addr_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(sctp_local_addr_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Change the call to take the transport parameter and set the
cached 'dst' appropriately inside the get_dst() function calls.
This will allow us in the future to clean up source address
storage as well.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in passing a destination address to
a get_saddr() call.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP never called xfrm_output after it's v6 route lookups so
that never really worked with ipsec. Additioanlly, we never
passed port nubmers and protocol in the flowi, so any port
based policies were never applied as well. Now that we can
fixed ipv6 routing lookup code, using ip6_dst_lookup_flow()
and pass port numbers.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 routing lookup does give us a source address,
but instead of filling it into the dst, it's stored in
the flowi. We can use that instead of going through the
entire source address selection again.
Also the useless ->dst_saddr member of sctp_pf is removed.
And sctp_v6_dst_saddr() is removed, instead by introduce
sctp_v6_to_addr(), which can be reused to cleanup some dup
code.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the below test case, using the source address routing,
sctp can not work.
Node-A
1)ifconfig eth0 inet6 add 2001:1::1/64
2)ip -6 rule add from 2001:1::1 table 100 pref 100
3)ip -6 route add 2001:2::1 dev eth0 table 100
4)sctp_darn -H 2001:1::1 -P 250 -l &
Node-B
1)ifconfig eth0 inet6 add 2001:2::1/64
2)ip -6 rule add from 2001:2::1 table 100 pref 100
3)ip -6 route add 2001:1::1 dev eth0 table 100
4)sctp_darn -H 2001:2::1 -P 250 -h 2001:1::1 -p 250 -s
root cause:
Node-A and Node-B use the source address routing, and
at begining, source address will be NULL,sctp will
search the routing table by the destination address,
because using the source address routing table, and
the result dst_entry will be NULL.
solution:
walk through the bind address list to get the source
address and then lookup the routing table again to get
the correct dst_entry.
Signed-off-by: Weixing Shi <Weixing.Shi@windriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change SCTP_DEBUG_PRINTK and SCTP_DEBUG_PRINTK_IPADDR to
use do { print } while (0) guards.
Add SCTP_DEBUG_PRINTK_CONT to fix errors in log when
lines were continued.
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Add a missing newline in "Failed bind hash alloc"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Herbert Xu said: we should be able to simply replace ipfragok
with skb->local_df. commit f88037(sctp: Drop ipfargok in sctp_xmit function)
has droped ipfragok and set local_df value properly.
The patch kills the ipfragok parameter of .queue_xmit().
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Convert to list macro's for the list of addresses per interface
in IPv6.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call_rcu() will unconditionally reinitialize RCU head anyway.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid touching device refcount in sctp/ipv6, thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct can_proto had a capability field which wasn't ever used. It is
dropped entirely.
struct inet_protosw had a capability field which can be more clearly
expressed in the code by just checking if sock->type = SOCK_RAW.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During peeloff/accept() sctp needs to save the parent socket state
into the new socket so that any options set on the parent are
inherited by the child socket. This was found when the
parent/listener socket issues SO_BINDTODEVICE, but the
data was misrouted after a route cache flush.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_is_any() function that is used to check for wildcard addresses
only looks at the address itself to determine the address family.
This function is used in the API to check the address passed in from
the user. If the user simply zerroes out the sockaddr_storage and
pass that in, we'll end up failing. So, let's try harder to determine
the address family by also checking the socket if it's possible.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL. Change callers to pass a
namespace pointer instead.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipfragok flag controls whether the packet may be fragmented
either on the local host on beyond. The latter is only valid on
IPv4.
In fact, we never want to do the latter even on IPv4 when PMTU is
enabled. This is because even though we can't fragment packets
within SCTP due to the prtocol's inherent faults, we can still
fragment it at IP layer. By setting the DF bit we will improve
the PMTU process.
RFC 2960 only says that we SHOULD clear the DF bit in this case,
so we're compliant even if we set the DF bit. In fact RFC 4960
no longer has this statement.
Once we make this change, we only need to control the local
fragmentation. There is already a bit in the skb which controls
that, local_df. So this patch sets that instead of using the
ipfragok argument.
The only complication is that there isn't a struct sock object
per transport, so for IPv4 we have to resort to changing the
pmtudisc field for every packet. This should be safe though
as the protocol is single-threaded.
Note that after this patch we can remove ipfragok from the rest
of the stack too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e9df2e8fd8 ("[IPV6]: Use
appropriate sock tclass setting for routing lookup.") also changed the
way that ECN capable transports mark this capability in IPv6. As a
result, SCTP was not marking ECN capablity because the traffic class
was never set. This patch brings back the markings for IPv6 traffic.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7cbca67c07 ("[IPV6]: Support
Source Address Selection API (RFC5014)") introduced NULL dereference
of asoc to sctp_v6_get_saddr in net/sctp/ipv6.c.
Pointed out by Johann Felix Soden <johfel@users.sourceforge.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
All IP addresses that are present in a system are duplicated on
struct sctp_sockaddr_entry. They are linked in the global list
called sctp_local_addr_list. And this struct unions IPv4 and IPv6
addresses.
So, there can be rare case, when a sockaddr_in.sin_addr coincides
with the corresponding part of the sockaddr_in6 and the notifier
for IPv4 will carry away an IPv6 entry.
The fix is to check the family before comparing the addresses.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the lists are circular, we need to explicitely tag
the address to be deleted since we might end up freeing
the list head instead. This fixes some interesting SCTP
crashes.
Signed-off-by: Chidambar 'ilLogict' Zinnoury <illogict@online.fr>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an netns parameter to ip6_route_output. That will allow to access
to the right routing table for outgoing traffic.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since most users of ipv6_get_saddr() pass non-NULL as
dst argument, use ipv6_dev_get_saddr() directly.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope. This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
ipv6.c | 12 ++++++------
protocol.c | 12 ++++++------
2 files changed, 12 insertions(+), 12 deletions(-)
I was notified by Randy Stewart that lksctp claims to be
"the reference implementation". First of all, "the
refrence implementation" was the original implementation
of SCTP in usersapce written ty Randy and a few others.
Second, after looking at the definiton of 'reference implementation',
we don't really meet the requirements.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When a new address is added, we must check if the new address does not
already exists. This patch makes this check to be aware of a network
namespace, so the check will look if the address already exists for
the specified network namespace. While the addresses are browsed, the
addresses which do not belong to the namespace are discarded.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long