Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection
When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations
For short frames, use MCS0; for long - MCS1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync with the wmi definitions from the firmware team
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.
To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.
Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"echo" used to be called when no firmware loaded to the NIC,
this causes error output.
Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use temporal variable for often used vring->swhead;
and use proper index in debug printing - vring->swhead
used before was modified in wil_vring_advance_head
and then increased value was used in debug print
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cw1200 driver implements suspend and resume callbacks and assigns them
to the suspend and resume fields of the device_driver struct. These
callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend function
is actually executed upon suspend and drop the empty resume function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I've been getting this error when building mainline kernels using
Fedora's config files:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c: In function ‘_rtl88ee_init_mac’:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:853:2: error: implicit declaration of function ‘rtl_hal_pwrseqcmdparsing’ [-Werror=implicit-function-declaration]
if (!rtl_hal_pwrseqcmdparsing(rtlpriv, PWR_CUT_ALL_MSK,
^
cc1: some warnings being treated as errors
scripts/Makefile.build:258: recipe for target 'drivers/net/wireless/rtlwifi/rtl8188ee/hw.o' failed
I'm not sure if this is the correct fix, but it does seem to allow the
build to complete. I suspect that this was broken by commit 34ed780a6a
(rtlwifi: Fix problems with building an allyesconfig). Most of the files
that removed the include of pwrseqcmd.h, added one for ../pwrseqcmd.h.
The rtl8188ee driver had it removed it but didn't add the include of the
file in the parent directory.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a MCI reset is done, make sure that AIC
is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the main AIC calibration function to
handle MCI_STATE_AIC_CAL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a function to handle the
MCI message MCI_STATE_AIC_START.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a routine to handle the MCI_STATE_AIC_CAL_RESET
message.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since various MCI messages need to be
handled, along with driver-level support
in upper layers, disable AIC for now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The platform_quirk element in the platform data was used
to change the way the IRQ is triggered. When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.
Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.
This will allow us to use standard irq DT definitions
later on.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The firmware frequently manages to trigger this, and there's
no known driver workaround, so stop warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
we unref IWL_MVM_REF_UCODE_DOWN on iwl_mvm_restart_complete().
Usually, the restart is initiated by iwl_mvm_nic_restart(),
which takes the reference before restarting the hw.
However, in D3 flow we might call ieee80211_restart_hw()
directly (in case of suspend error and on d3_test-resume),
which without taking the ref first. fix it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware has a race in the flow that indicates the
completion of the authentication. Checking the completion
of the authentication is not really needed anyway since
we can wait for the ALIVE notification instead.
Remove the unneeded and buggy code.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the driver callback returns that it's out of space for new
stations, the mac80211 IBSS code still keeps the station so it
doesn't try to add it over and over again.
Since the rate scaling algorithm is separate in mac80211, it also
invokes the rate scaling algorithm for such stations. It doesn't
know that our rate scaling algorithm is tightly integrated with
the MVM code and relies on those data structures, and it cannot
as the abstraction doesn't allow for it.
This leads to crashes when the rate scaling algorithm tries to
use uninitialized data, notably the mvmsta->vif pointer.
Protect against this in the rate scaling algorithm. We cannot get
good rates with such peers anyway since the firmware cannot do
anything with them.
This should fix https://bugzilla.kernel.org/show_bug.cgi?id=93461
CC: <stable@vger.kernel.org>
Reported-by: Richard Taylor <rjt-kernel@thegrindstone.me.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This warning is misleading. In many cases, for example P2P ROC time
events, this will happen if the time event is aborted, for example
due to a higher priority time event. This is entirely normal and not
worth warning about.
In other cases, where we actually do act upon this, for example when
trying to connect and this fails, we should instead warn as part of
the disconnect operation.
Change the code to do that, i.e. make the warning a debug message,
and make it more prominent (an error) when we actually disconnect
because of it.
This also fixes confusion in the logs - the warning was mistaken for
something that needed investigation, while in most cases it's just
expected behaviour that occasionally some lower-priority time events
would not complete fully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In 8000 HW family B-step only, the ICCM is separate
from the SRAM. This adds the ICCM to the dump data
collected for FW debug.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are transport that must buffer frames in the driver.
This means that we have frames that are not in the op_mode
and not visible to the firwmare. This causes issues when we
flush the queues: the op_mode flushes a queue, and the
firmware flushes all the frames that are *currently* on the
rings, but if the transport buffers frames, it can submit
these while we are flushing. This leads to a situation
where we still have frames on the queues after we flushed
them.
Preventing those buffered frame from getting into the
firmware is possible, but then, we have to run the Tx
response path on frames that didn't reach the firmware
which is not desirable.
The way I solve this here is to let these frames go to the
firmware, but make sure the firmware will not transmit them
(by setting the station as draining). The op_mode then needs
to wait until the transport itself is empty to be sure that
the queue is really empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For each RX packet until this patch there only was a debug
print of the HCMD and the offset. This adds also the
sequence number of the packet for easier matching between
what was sent, what came back / was received, and what
got stuck somewhere and was never responded by the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to FW methodology, the capability bits should be the only ones
that change per-HW. The API bits should remain constant across different
HWs.
Currently this is not the case with multi-source LAR (API bit 9). Assign
a new capability bit to eventually replace the API bit. Until the API bit
can be deprecated, the driver will check either to enable multi-source
LAR.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If, on a GO, the CSA time event fails to be scheduled, continue the
flow towards mac80211's state machine so it doesn't get stuck, but
report an error later on the post switch which will cause mac80211
to tear down the operation. This ensures nothing gets stuck due to
the scheduling failure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.
mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.
SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During profiling, we discovered that driver remains idle for time
when pakcet is downloaded to FW but no TX_DONE has been received
i.e. while data_sent is true.
This patch adds enhancement to TX routine where we preprocess
packets from TX queue, make them ready for TX and add them to
separate TX queue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch does away with spinlock in
mwifiex_wmm_get_highest_priolist_ptr in order to improve TP.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes BA setup helper routines
mwifiex_is_bastream_setup and mwifiex_is_amsdu_in_ampdu_allowed.
Current code will use two functions to check bastream setup and
amsdu in ampdu. This patch change these functions to flags, thus
avoiding redundant spin_lock check while dequeuing TX packets.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.
This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD8897 support buffers of 4K and 16 such ports can be accomodated.
So basically 64K buffer size in single aggregation is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename this function to reflect its purpose correctly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e8 ("wl18xx: use new fw stats structures")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I have here FRITZ!WLAN USB Stick N v2 / idVendor=057c, idProduct=8501
and every single of this requests ends up with:
|ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -32
I was browsing the the vedor code and I haven't seen such request so I
remove it with this patch. If I wasn't look enough or if this error is
expected then please excuse :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800usb_autorun_detect() blindly assumes assumes that it worked while
it could have failed. Check the error code here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My understanding ist that rt2x00usb_register_read() is void and so the
reader is unaware of read errors and assumes that whatever was on the
stack as it was about to read.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might be in interrupt context at few places. So replace
del_timer_sync() with del_timer(). This patch fixes a kernel
trace problem seen occasionally during our testing.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed Rx aggregated packets are always followed
by a single Rx packet. This patch improves our logic to add
that extra packet in next aggregation.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In HT40 modes, pulse events on primary and extension
channel are processed individually. If valid, a pulse
event will be fed into the detector
* for primary frequency, or
* for extension frequency (+/-20MHz based on HT40-mode)
* or both
With that, a 40MHz radar will result in two individual
radar events.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support HT40 DFS mode, a triggering detector must
reset only itself but not other detector lines.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TPC support has been observed to cause some tx power fluctuations on
some devices with at least AR934x and AR938x chips.
Disable it for now until the bugs have been found and fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sc->nbcnvifs tracks assigned beacon slots, not enabled beacons.
Therefore, it cannot be used to decide if cur_conf->enable_beacon (bool)
should be updated, or if beacons have been enabled already.
With the current code (depending on the order of calls), beacons often
do not get enabled in an AP+STA setup.
To fix tracking of enabled beacons, convert cur_conf->enable_beacon to a
bitmask of enabled beacon slots.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog timer is used to put the device in a low-power mode when
it is idle for some time. This timer is stopped during that mode and
should be restarted upon activity. This has been broken by commit
d4150fced0365 ("brcmfmac: Simplify watchdog sleep."). This patch
restores the behaviour as it was before that commit.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware provides pointer to SDIO shared information at end of
RAM during firmware initialization. End of RAM is obviously determined
by the actual ram size, but part of that may be used for save&restore
memory. In that case another location in RAM will hold the pointer.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of hard-coded memory sizes it is possible to obtain that
information from the internal memory registers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the brcmf_chip_attach() function responsible for putting the
device in a state where it is accessible for firmware download.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions brcmf_chip_[enter/exit]_download() are not exclusively
used for firmware download so rename these more appropriate.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of checking the cores in the chip only if CONFIG_BRCMDBG
is selected perform the check always and extend it with more sanity
checking.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing the ramsize from the brcmf_sdio structure to avoid
duplication. The information is available in brcmf_chip
structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pre-requisite to shrink size of ieee80211_tx_info which in turn is
needed to shrink skb->cb to 40 bytes again.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we want to shrink skb->cb then we'd have to see about
reducing struct ieee80211_tx_info, which gets embedded inside
skb->cb[].
It provides a scratch space to be used by wireless drivers.
ar5523 uses the maximum space available today (40 bytes), but it seems
we don't need this -- data->skb pointer seems to always point back to the
skb whose cb buffer the data structure resides, iow, given a pointer to the
embedded control buffer we can infer the skb address.
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the RTT registers need to be configured for all
valid chains irrespective of the runtime chainmask,
use the actual chainmask of the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When assigning the initvals for PCIE sleep/awake
registers, check the configuration that has been
assigned to pll_pwrsave during initialization. Also,
display a warning if we don't have valid arrays.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the value in ah->config.pll_pwrsave to determine
which array needs to be loaded. Also, initialize
pll_pwrsave to 1 by default.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These will be used to handle chip-specific
power save configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the AP, configuration may say not to bridge traffic between
wireless clients. This is conveyed from user space (ex: hostapd has
ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's
cfg80211 ops method change_bss
Add support for this setting.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is for AP only. If Rx data frame targeted to one of associated clients,
transmit it back to the wireless media and don't deliver to the host.
For the multicast frames, deliver to both host and wireless media.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is expected that driver completes NAPI when less than
full budget is consumed.
Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes add support for BCM4345 SDIO chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Syed Asifful Dayyan <syedd@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Msgbuf is using a wait_event_timeout to wait for the response on
an ioctl. The wakeup routine uses waitqueue_active to see if
wait_event_timeout has been called. There is a chance that the
response arrives before wait_event_timeout is called, this
will result in situation that wait_event_timeout never gets
woken again and assumed result will be a timeout. This patch
removes that errornous situation by always setting the
ctl_completed var before checking for queue active.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is using a "shared" variable to handoff ctl frames to DPC
and to see when they are done. In a timeout situation this can
lead to erroneous situation where DPC started to handle the ctl
frame while the timeout expired. This patch will fix this by
adding locking around the shared variable.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The watchdog thread is used to put the SDIO bus to sleep when the
system is idling. This patch simplifies the way it is determined
when sleep can be entered.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On removal of SDIO card both functions of card will be getting
a remove call. When the first is hanging in ctrl frame xmit then
the second will cause oops. This patch fixes the xmit ctrl
handling in case of serious errors and also limits the handling
for remove to function 1 only.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To prepare for reset ath5k should finish all asynchronous tasks. At
first, it disables the interrupt generation, then it waits for the
interrupt handler and tasklets completion, and then proceeds to the HW
configuration update. But it does not consider that the interrupt
handler or tasklet re-enables the interrupt generation. And we fall in a
situation when ath5k assumes that interrupts are disabled, but it is
not.
This can lead to different consequences, such as reception of the frame,
when we do not expect it. Under certain circumstances, this can lead to
the following warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
Fix this issue by adding a new status flag, which forbids to re-enable
the interrupt generation until the HW configuration is completed.
Note: previous patch, which reorders the Rx disable code helps to avoid
the above warning, but not fixes the root cause of unexpected frame
receiving.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath5k updates the channel pointer and after that it stops the Rx logic
and apply channel to HW. In case of channel switch, such sequence
creates a small window when a frame, which is received on the old
channel is considered as a frame received on the new one.
The most notable consequence of this situation occurs during the switch
from 2 GHz band (CCK+OFDM) to the 5GHz band (OFDM-only). Frame received
with CCK rate, e.g. beacon received at the 1mbps, causes the following
warning:
WARNING: at ath5k/base.c:589 ath5k_tasklet_rx+0x318/0x6ec [ath5k]()
invalid hw_rix: 1a
[..]
Call Trace:
[<802656a8>] show_stack+0x48/0x70
[<802dd92c>] warn_slowpath_common+0x88/0xbc
[<802dd98c>] warn_slowpath_fmt+0x2c/0x38
[<81b51be8>] ath5k_tasklet_rx+0x318/0x6ec [ath5k]
[<8028ac64>] tasklet_action+0x8c/0xf0
[<80075804>] __do_softirq+0x180/0x32c
[<80196ce8>] irq_exit+0x54/0x70
[<80041848>] ret_from_irq+0x0/0x4
[<80182fdc>] ioread32+0x4/0xc
[<81b4c42c>] ath5k_hw_set_sleep_clock+0x2ec/0x474 [ath5k]
[<81b4cf28>] ath5k_hw_reset+0x50/0xeb8 [ath5k]
[<81b50900>] ath5k_reset+0xd4/0x310 [ath5k]
[<81b557e8>] ath5k_config+0x4c/0x104 [ath5k]
[<80d01770>] ieee80211_hw_config+0x2f4/0x35c [mac80211]
[<80d09aa8>] ieee80211_scan_work+0x2e4/0x414 [mac80211]
[<8022c3f4>] process_one_work+0x28c/0x400
[<802df8f8>] worker_thread+0x258/0x3c0
[<801b5710>] kthread+0xe0/0xec
[<800418a8>] ret_from_kernel_thread+0x14/0x1c
The easiest way to reproduce this warning is to run scan with dualband
NIC in noisy environments, when the channel 11 runs multiple APs. In my
tests if the APs num >= 12, the warning appears in the first few
seconds of scanning.
In order to fix this, the Rx disable code moved to a higher level and
placed before the channel pointer update. This is also makes the code a
bit more symmetrical, since we disable and enable the Rx in the same
function.
In fact, at the pointer update time new frames should not appear,
because interrupt generation at this point should already be disabled.
The next patch should address this issue.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* 8000 device family work
* Update to the BT Coex firmware API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=l2Ap
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-03-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Location Aware Regulatory was added by Arik
* 8000 device family work
* Update to the BT Coex firmware API
The return value in iwl_mvm_get_wakeup_status() is a bit unclear in
that it's not obvious that we don't leak fw_status in some cases.
Use fw_status directly with ERR_PTR() and return only it, that way
the compiler has a chance of proving that it's uninitialized (if it
ever is due to new changes.)
Additionally, this removes a smatch warning since smatch couldn't
figure out that fw_status can't, in fact, leak here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after
calling iwl_mvm_query_wakeup_reasons(), because this function unlocks
it already. Move the goto out_iterate outside the #ifdef.
Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The code here is a little confusing, the iwl_mvm_te_check_disconnect()
will check that the interface is a station, but going into it after
already having processed the time even end for P2P seems strange at
first look.
Put a switch statement there to distinguish the interface types and
make this more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We previously enabled the smart FIFO (SF) in BSS only after
association.
This cause interrupt latency on P2P on certain devices.
Change the working model to enable the SF all the time and
play with the timeout values based on the association state.
This change was not tested on older firwmares, so make it
happen only on -13.ucode and up.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
More sub system IDs were introduced for the 8260 series.
Add the new sub system IDs so the cards can be recognized.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware was not using the new API, so we don't need to
differentiate between the different stages of this new API.
The main difference here is that most of the hard coded
values are not sent through the command anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The newer devices will enable a new register for this
(DEVICE_SET_NMI_8000B_REG), but the interrupt handler
isn't wired yet.
Keep the old register for now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a station goes to sleep, we can't transmit any frame
to it. This means that until that station will wake up, a
queue that is dedicated to this station won't progress at
all. Take this into account when monitoring stuck queues
and don't account for the time the station was asleep.
This allows to mask false positives where the queues are
stuck not because of a bug, but because of the station
being asleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows the op_mode to let the transport know that a
queue is currently frozen and that its timer should be
stopped.
When the queue is unfrozen, its timer should be set to
expire after the remainder of the timeout has elapsed.
This can be used when stations go to sleep. When a station
goes to sleep, the op_mode can freeze the timer so that the
queue will never be considered as stuck. When the station
wakes up, the queue will be unfrozen.
This is meant to avoid false positives that would happen if
a buggy station goes to sleep for a very long time. In case
we have a dedicated queue for this station (BA agreement)
and it goes to sleep for a very long time, the queue would
rightfully be stopped during all that time. In this case,
the stuck queue timer could fire and that would be a false
positive.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Tx statistics weren't updated when using fixed rate for
debugging. Fix this as Tx statistics are useful in this use case.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
RTNL is not taken during CT-kill so regulatory APIs cannot be invoked.
That's fine, since the HW is only brought up to check the temperature
during CT-kill. We don't expect Tx or scanning.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When using IBSS, it's easily possible to exhaust the number
of available stations in the driver, so don't warn on it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.
Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New sub system IDs were introduced for the 8260 series.
This patch adds them so new 8260 cards can be recognized.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make the print a bit more readable.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When entering D0i3, the MVM mutex cannot be grabbed. This interferes
with the calculation of the number of connected TDLS stations during
the setup of the power cmd.
The goal is to disable power saving for all vifs while any TDLS station
is connected. For this purpose it is enough to keep the pm_enabled
member of all mvmvifs as false. An update of the power state already
occurs when a TDLS station is added/removed, so the values are correctly
updated.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New NVM versions in LnP platforms have the lar_enable bits in a different
offset.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't need to acquire MAC access for each access, it
makes much more sense to keep the MAC access. This speeds
up the Tx DMA stop flow significantly.
Moreover, if one channel can't be stopped, stop the others
but don't poll for them to avoid being stuck there for a
long time.
This solves a situation in which we were stuck in that flow
for way too long with a spinlock held which led to a kernel
panic.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we associate we always need to update the quotas. This
fixes a bug for cases in which quotas weren't udapted after
association.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This module parameter is useful for debugging NVM and LAR related issues.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
11ac depends on 11n, so disable it if 11n is disabled.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If LAR is supported in TLV, but the NVM does not enable it, then disable
LAR support and ignore the TLV's bit that enabled LAR.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
max_eirp affects the txpower configured to the power,
so use the max tx power (22) instead of some other
value.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix the last 5ghz channel to 165 instead of 161
Add support for 8000 family, until channel 181.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Otherwise the regulatory data will mistakenly contain only 7000 series
channels.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Chub (Communication Hub, CommsHUB) is a HW component that connects to the cellular
and connectivity cores that gets updates of mcc changes, and then notifies the FW
directly of any mcc change.
The ucode notifies the driver (via this command) that it should ask for an mcc update,
and the driver sends the ucode the update mcc command to set the updated regulatory info.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove a useless debug print about unsupported channels.
Also add a comment about the LAR special case where channels
might become valid later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to updated regulatory guidelines, the ACTIVE bit in the NVM
also allows ibss activity on the channel. The IBSS NVM bit is not updated
when LAR is active and is deprecated. Using this bit for NO-IR incorrectly
causes all 5Ghz channels to be marked as passive.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Register to cfg80211 with all channels enabled when LAR is supported.
Appropriate channels will later be disabled when a specific regulatory
domain is defined.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Parse the NVM channel data and create a regulatory domain with a rule
for every 20Mhz channel. Use the AUTO_BW flag so the regulatory core
can unify single-channel rules into ranges.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During init queue a regulatory update to retrieve the default
regulatory settings from FW. If we're during recovery, only replay the
current country code to FW, if it exists.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new API sets an MCC (mobile country code) to FW and receives a
channel structure to be used as a basis for an updated regulatory domain.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf318 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If this situation ever happens, the mac80211 state machine gets
confused because it never clears csa_active. There was a separate
bug that lead to this happening with a working connection, but it
isn't very robust to try to keep the connection up in this case.
When removing the time event the CSA essentially procedure stops,
so the safest thing to do is to disconnect in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 now informs the driver when to drop the packets
upon flush(). This will happen before disconnecting, or
before we shut down the interface. We can now rely on this
to drop all the packets including the VO queues.
When mac80211 sets drop to false, wait for all the queues
to be empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU/vcnAAoJEG4XJFUm622bBbMIAJAmmITit1LFbm5L5zguIkVq
b9ppfEkgz6JYb4KMe6jWnvrc9yM3ywslH2Evo09ChA53A2sUhORKxlolreGTZxtQ
je3twmUCyzkbvss+aKFS4BzEDDOGwW9A/wk3LT4TZJ7Jp626k1wPXN5WZHaDh0YC
pE7fH6jnNg2Qoe68tG8WmTqrYlzU6mLpI0NNxsW+h2tK2Gqm7jSoMy96RPiwS0ZV
BFnxrJJZViMyPit48pZf338pdndkxOIlDBIJCY8qUwQIt4HxQ8DnmsLWqg9xjnfT
mSO9xgSJxfR02ZDIBYqaK41KlcharjwrF5lDi+JHkoHB2SQQM9A/noxpWu4/JGI=
=pOSK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
Signed-off-by: David S. Miller <davem@davemloft.net>
The commits below broke compilation when
CONFIG_IWLWIFI_DEBUGFS is not set.
FIx that.
Fixes: ddf89ab10a ("iwlwifi: mvm: allow to force the Rx chains from debugfs")
Fixes: 9d761fd8a5 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A short or malformed vendor command buffer could cause reads outside
the command buffer.
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
[arend@broadcom.com: slightly modified debug trace output]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac:
* sdio improvements
* add a debugfs file so users can provide us all the revinfo we could
ask for
iwlwifi:
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
ath9k:
* add per-vif TX power capability
* BT coexistance fixes
ath10k:
* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default
bcma:
* enable support for PCIe Gen 2 host devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+dliAAoJEG4XJFUm622bsqQH/RO1Gxuw6hmiHPeeIcoDmlvt
MZKvy6xcAiFqREfGwDxjVminlTZ7/MB9bABeaoQKzpQFpCJW/ftjIqwfbRqZWsvG
3IC0s2nPTwWU8YSsZTbifnyXCVNQDJuE+5nQ3hMO2rE/dZDi1zt1fS2hiSXtlASS
kgBJcfXgoVxvhZ1WI+uVpbU0RtwXmI7tVylREE1sbgCrg7AuJx4Q2QmZ1GioPRLy
20HnFVFcIcbHk4eXVwAJOspdjctujoR858pg/oxlcVXWb7MOOCV/Fk8WMursZxFh
qj/I/kbDcFYh3H5uC+6qL/kRByY80/yckLDiMbghA0QR5/PSx2nvp/UfkqIf008=
=qgVl
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
brcmfmac:
* sdio improvements
* add a debugfs file so users can provide us all the revinfo we could
ask for
iwlwifi:
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
ath9k:
* add per-vif TX power capability
* BT coexistance fixes
ath10k:
* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default
bcma:
* enable support for PCIe Gen 2 host devices
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit below introduced an unsafe dereference of
mvmvif->phy_ctxt. It can be NULL even if we hold the mutex.
We can be handling a BT Coex notification while the vif has
already been unassigned. This can happen since the BT Coex
notification is hanled asynchronuously: we can have started
to handle the BT Coex notification trying to acquire the
mutex while the unassign flow already got it. The BT Coex
notification handling will wait for the mutext. I'll get it
later, but then mvmvif->phy_ctxt will be NULL.
Panic log:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f985180d>] iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
*pdpt = 0000000000000000 *pde = f000eef300000007
Oops: 0000 [#1] SMP
Workqueue: events iwl_mvm_async_handlers_wk [iwlmvm]
task: ed719b20 ti: ec03e000 task.ti: ec03e000
EIP: 0060:[<f985180d>] EFLAGS: 00010202 CPU: 2
EIP is at iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
EAX: 00000000 EBX: f6d3cb70 ECX: f6d3cb70 EDX: 00000000
ESI: ec03fe40 EDI: efeb8810 EBP: ec03fdf0 ESP: ec03fdac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000000 CR3: 01a1a000 CR4: 001407f0
Stack:
f743ca80 f744a404 ec03fdcc c10e3952 00003aba f743ca80 00000246 f743ca80
00000246 00000000 00000001 00000000 ebd45ff6 ebd458a4 f6d3c500 ebd45578
ebd44b01 ec03fe18 f99e1bc2 00000002 ebd44bc0 f9851770 00000000 f6d3c500
Call Trace:
[<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
[<f99e1bc2>] __iterate_interfaces+0x82/0x110 [mac80211]
[<f9851770>] ? iwl_mvm_bt_coex_reduced_txp+0x140/0x140 [iwlmvm]
[<f99e1c6a>] ieee80211_iterate_active_interfaces_atomic+0x1a/0x20 [mac80211]
[<f9851427>] iwl_mvm_bt_coex_notif_handle+0x77/0x280 [iwlmvm]
[<f9852161>] iwl_mvm_rx_bt_coex_notif_old+0x211/0x220 [iwlmvm]
[<f9850b8b>] iwl_mvm_rx_bt_coex_notif+0x19b/0x1b0 [iwlmvm]
[<f983944f>] iwl_mvm_async_handlers_wk+0x7f/0xe0 [iwlmvm]
CC: <stable@vger.kernel.org> [3.19+]
Fixes: 123f515635 ("iwlwifi: mvm: BT Coex - add support for TTC / RRC")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.
Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Scott Branden