it will reduce exution time from 14ms to 2ms on ar9271
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function uses mixed styles for register names/numbers which
is make harder reading and optimisation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.
In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2).
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Seems H/W report correctly firmware Autorun value only at initialization
stage. When we close interface and open it again, Autorun value is 0 and
we try to load firmware what kills the device. To fix clear
REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we
discover Autorun mode.
Reported-and-tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
was loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wIgU
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-03-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix a memory leak: we leaked memory each time the module
was loaded.
In the reset flow, the driver cancels ongoing scan and sends scan
complete notification to mac80211. However it does not clean its UID.
Add cleaning scan UID for the ongoing scan. Loop over all other UIDs
to make sure there's nothing left there and warn if any is found.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a strong relationship between the NVM version and
the hardware step. Enforce that in the driver in case the
default NVM on the platform is the wrong one.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The semaphore may not be accessible. Fix the debug prints
accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes we will want to configure the timeouts for the
Tx queues based on the vif type. Allow to do that using the
trigger mechanism.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to implement the enable_scan_iteration_notif handling
explicitly and there's no reason not to export the current value. So
use debugfs_create_bool() instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for delaying the start of a scheduled scan (or a WoWLAN
net-detect scan).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ref_count is currently initialized on start_fw(). This causes
some issues in restart flow, as currently active references
(e.g. unclaimed command) will get cleared, resulting in
invalid reference accounting.
Move the ref_count initialization to the configure() trans op,
so it won't be re-initialized on restart.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In nic restart flow we inform mac80211 that scan was aborted, but it was
based only on scan_status which is not set by UMAC scan. Fix that.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The AP_START d0i3 reference was never removed if the AP started correctly.
This has the unpleasant side-effect of preventing D0i3 on Android if the
WiFi hotspot was ever started on the device.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVEQL4AAoJEG4XJFUm622boBwH/R61GyJvh2OieOfv35fv84N0
h4abht9N4gfogwJcF9AT0rPddo+ueYhD1pSYOS6pyM1d2OjhJq73vEVetCUKpX46
TpFw2hZOOZKj97flYyi7dPXQxGcUYLAzfqZ5Dn45czGuwMk/v3v+Ni3lzHUfmKvm
jrjHWKm2+WiJGRO7xJEmUAZoXTLEZdQtxLC3oViIeldhjsS5XQfx6K7mlp6L/7lC
zvHBSkLFEjjn6fMa17r9GgCsN7HkHuK8/tbXfbDyVw37bWte/6ZJv+1IUn6HPUKJ
mCRl5Sbs/+Rg0sqWaf1ygjGCghx9I7U4R9EvaZxpSnn+KjeeL4ibds2Lq+DoAaM=
=fEF3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
rtlwifi:
* fix IOMMU mapping leak in AP mode
brcmfmac:
* disable MBSS feature for BCM43362 to get AP mode working again
ath9k:
* disable Transmit Power Control (TPC) again due to regressions
* fix beaconing issue with AP+STA setup
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have wlcore device-tree bindings in place
(for both wl12xx and wl18xx), remove the legacy
wl12xx_platform_data struct, and move its members
into the platform device data (that is passed to wlcore)
Davinci 850 is the only platform that still set
the platform data in the legacy way (and doesn't
have DT bindings), so remove the relevant
code/Kconfig option from the board file (as suggested
by Sekhar Nori)
Since no one currently uses wlcore_spi, simply remove its
platform data support (DT bindings will have to be added
if someone actually needs it)
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When running with device-tree, we no longer have a board file
that can set up the platform data for wlcore.
Allow this data to be passed from DT.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead. Also add a
boolean to specify whether the clock is XTAL or not.
Change all board files to reflect this.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - small fixes, update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In this routine, kzalloc allocates a memory block. This allocation is
freed in the error paths, but not in the normal exit, thus the allocation
is leaked.
The kmemleak facility was used to find the leak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:
>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
With patch '960d6d08e39 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.
This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no known BCM4354 PCIe devices released so removing
support from the driver until proven otherwise.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently support was added for the BCM4345 SDIO chipset by
commit 9c51026509 ("brcmfmac: Add support for BCM4345 SDIO chipset")
however this was verified using a BCM43455 device, which is
a more recent revision of the chip. This patch assure that
older revisions are not probed as they would fail.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Syed Asifful Dayyan <syedd@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM4356 PCIe wireless device was added recently but overlooked
the fact that the MODULE_FIRMWARE() macros were missing for the
firmwares needed by this device.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO uses a thread to handle all communication with the device,
for this data is exchanged between threads. This data needs proper
memory barriers to make sure that data "exchange" is going correct.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several host controllers supporting runtime-pm are causing issues
with our sdio wireless cards because they disable the sdio interrupt
upon going into runtime suspend. This patch avoids that by doing
a pm_runtime_forbid() call during the probe. Tested with Sony Vaio
Duo 13 which uses sdhci-acpi host controller.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's clear from the indenting that curly braces were intended here.
Fixes: e35000ead4 ('mwifiex: preprocess packets from TX queue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection
When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations
For short frames, use MCS0; for long - MCS1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync with the wmi definitions from the firmware team
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.
To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.
Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"echo" used to be called when no firmware loaded to the NIC,
this causes error output.
Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use temporal variable for often used vring->swhead;
and use proper index in debug printing - vring->swhead
used before was modified in wil_vring_advance_head
and then increased value was used in debug print
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cw1200 driver implements suspend and resume callbacks and assigns them
to the suspend and resume fields of the device_driver struct. These
callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend function
is actually executed upon suspend and drop the empty resume function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I've been getting this error when building mainline kernels using
Fedora's config files:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c: In function ‘_rtl88ee_init_mac’:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:853:2: error: implicit declaration of function ‘rtl_hal_pwrseqcmdparsing’ [-Werror=implicit-function-declaration]
if (!rtl_hal_pwrseqcmdparsing(rtlpriv, PWR_CUT_ALL_MSK,
^
cc1: some warnings being treated as errors
scripts/Makefile.build:258: recipe for target 'drivers/net/wireless/rtlwifi/rtl8188ee/hw.o' failed
I'm not sure if this is the correct fix, but it does seem to allow the
build to complete. I suspect that this was broken by commit 34ed780a6a
(rtlwifi: Fix problems with building an allyesconfig). Most of the files
that removed the include of pwrseqcmd.h, added one for ../pwrseqcmd.h.
The rtl8188ee driver had it removed it but didn't add the include of the
file in the parent directory.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a MCI reset is done, make sure that AIC
is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the main AIC calibration function to
handle MCI_STATE_AIC_CAL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a function to handle the
MCI message MCI_STATE_AIC_START.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a routine to handle the MCI_STATE_AIC_CAL_RESET
message.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since various MCI messages need to be
handled, along with driver-level support
in upper layers, disable AIC for now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The platform_quirk element in the platform data was used
to change the way the IRQ is triggered. When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.
Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.
This will allow us to use standard irq DT definitions
later on.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The firmware frequently manages to trigger this, and there's
no known driver workaround, so stop warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
we unref IWL_MVM_REF_UCODE_DOWN on iwl_mvm_restart_complete().
Usually, the restart is initiated by iwl_mvm_nic_restart(),
which takes the reference before restarting the hw.
However, in D3 flow we might call ieee80211_restart_hw()
directly (in case of suspend error and on d3_test-resume),
which without taking the ref first. fix it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware has a race in the flow that indicates the
completion of the authentication. Checking the completion
of the authentication is not really needed anyway since
we can wait for the ALIVE notification instead.
Remove the unneeded and buggy code.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the driver callback returns that it's out of space for new
stations, the mac80211 IBSS code still keeps the station so it
doesn't try to add it over and over again.
Since the rate scaling algorithm is separate in mac80211, it also
invokes the rate scaling algorithm for such stations. It doesn't
know that our rate scaling algorithm is tightly integrated with
the MVM code and relies on those data structures, and it cannot
as the abstraction doesn't allow for it.
This leads to crashes when the rate scaling algorithm tries to
use uninitialized data, notably the mvmsta->vif pointer.
Protect against this in the rate scaling algorithm. We cannot get
good rates with such peers anyway since the firmware cannot do
anything with them.
This should fix https://bugzilla.kernel.org/show_bug.cgi?id=93461
CC: <stable@vger.kernel.org>
Reported-by: Richard Taylor <rjt-kernel@thegrindstone.me.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The assumption before this patch was that we don't need to
run again the INIT firmware after the system booted. The
INIT firmware runs calibrations which impact the physical
layer's behavior.
Users reported that it may be helpful to run these
calibrations again every time the interface is brought up.
The penatly is minimal, since the calibrations run fast.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=94341
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This warning is misleading. In many cases, for example P2P ROC time
events, this will happen if the time event is aborted, for example
due to a higher priority time event. This is entirely normal and not
worth warning about.
In other cases, where we actually do act upon this, for example when
trying to connect and this fails, we should instead warn as part of
the disconnect operation.
Change the code to do that, i.e. make the warning a debug message,
and make it more prominent (an error) when we actually disconnect
because of it.
This also fixes confusion in the logs - the warning was mistaken for
something that needed investigation, while in most cases it's just
expected behaviour that occasionally some lower-priority time events
would not complete fully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In 8000 HW family B-step only, the ICCM is separate
from the SRAM. This adds the ICCM to the dump data
collected for FW debug.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are transport that must buffer frames in the driver.
This means that we have frames that are not in the op_mode
and not visible to the firwmare. This causes issues when we
flush the queues: the op_mode flushes a queue, and the
firmware flushes all the frames that are *currently* on the
rings, but if the transport buffers frames, it can submit
these while we are flushing. This leads to a situation
where we still have frames on the queues after we flushed
them.
Preventing those buffered frame from getting into the
firmware is possible, but then, we have to run the Tx
response path on frames that didn't reach the firmware
which is not desirable.
The way I solve this here is to let these frames go to the
firmware, but make sure the firmware will not transmit them
(by setting the station as draining). The op_mode then needs
to wait until the transport itself is empty to be sure that
the queue is really empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For each RX packet until this patch there only was a debug
print of the HCMD and the offset. This adds also the
sequence number of the packet for easier matching between
what was sent, what came back / was received, and what
got stuck somewhere and was never responded by the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to FW methodology, the capability bits should be the only ones
that change per-HW. The API bits should remain constant across different
HWs.
Currently this is not the case with multi-source LAR (API bit 9). Assign
a new capability bit to eventually replace the API bit. Until the API bit
can be deprecated, the driver will check either to enable multi-source
LAR.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If, on a GO, the CSA time event fails to be scheduled, continue the
flow towards mac80211's state machine so it doesn't get stuck, but
report an error later on the post switch which will cause mac80211
to tear down the operation. This ensures nothing gets stuck due to
the scheduling failure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.
mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.
SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During profiling, we discovered that driver remains idle for time
when pakcet is downloaded to FW but no TX_DONE has been received
i.e. while data_sent is true.
This patch adds enhancement to TX routine where we preprocess
packets from TX queue, make them ready for TX and add them to
separate TX queue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch does away with spinlock in
mwifiex_wmm_get_highest_priolist_ptr in order to improve TP.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes BA setup helper routines
mwifiex_is_bastream_setup and mwifiex_is_amsdu_in_ampdu_allowed.
Current code will use two functions to check bastream setup and
amsdu in ampdu. This patch change these functions to flags, thus
avoiding redundant spin_lock check while dequeuing TX packets.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.
This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD8897 support buffers of 4K and 16 such ports can be accomodated.
So basically 64K buffer size in single aggregation is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename this function to reflect its purpose correctly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e8 ("wl18xx: use new fw stats structures")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I have here FRITZ!WLAN USB Stick N v2 / idVendor=057c, idProduct=8501
and every single of this requests ends up with:
|ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x0c failed for offset 0x0000 with error -32
I was browsing the the vedor code and I haven't seen such request so I
remove it with this patch. If I wasn't look enough or if this error is
expected then please excuse :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800usb_autorun_detect() blindly assumes assumes that it worked while
it could have failed. Check the error code here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My understanding ist that rt2x00usb_register_read() is void and so the
reader is unaware of read errors and assumes that whatever was on the
stack as it was about to read.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might be in interrupt context at few places. So replace
del_timer_sync() with del_timer(). This patch fixes a kernel
trace problem seen occasionally during our testing.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Oleksij Rempel