Use the new compatible introduced in order to benefit of a wider and
more accurate range of baud rates to be used.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
DNS-327L is a 2-bay NAS with the following specs:
- 512MiB RAM
- 128MiB NAND Flash
- 1 GbE interface (Marvell PHY)
- 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
- 2 internal SATA ports handled by the Armada 370:
uses 2 gpios for power control
- two front 2-color leds (amber + white) for both discs,
controlled by the SoC
- One white LED handled by SoC (USB)
- 3 buttons. Power handled by weltrend, USB and
RESET (on the bottom) are wired via GPIOs
- Unidentified i2c device at address 0x13 (via i2cdetect)
- UART0 providing serial console
- Weltrend MCU serving for RTC, temperature, fan control,
and power button handling interfaced via UART1
(Handled via userspace dns320l-daemon)
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch updates the in tree-users of the SSD1306 controller for using
the newly introduced DT properties.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).
Both boards have:
- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM
gregory.clement@free-electrons.com: use serial0:115200n8 in
stdout-path and remove the bootargs part in the chosen node
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch sets display clock correctly. If Display clock isn't set
correctly then you would find below messages and Display controller
doesn't work correctly.
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
Fixes: abc0b1447d ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXvpAAAoJEAf03oE53VmQxx0IAMegPIH5rS0NIC+XmwpFnmre
L0bP0dRdKHS5uRxsZfD7F0WF61JiOuLzgX/rIIclnllvvKMPVW+CEs1KnfWVP33u
9FfFIErkGnYeJjs7Lj1j1lb9ESkJfqapMwTfl74mod8QFOT3cgXOiUu8pgHIp2cF
OTR6W5vkv1KoR8E0B4nGv9wZmRBeujtxW+2nIZZVcAglxfOHkJfqlfQ5wCQtdsnU
7K45r4WTbM632hIW5XA3OlzCuuIWs2Hr591aW8PY4KLMPB39HcCV/eTxJMGRbg1Q
4baSQ0xN+DhPfJary0Nc6Y2QXxZWb9y2ElGrqVMlbanCV7xaUGUGYrZ14heRvRs=
=ubIG
-----END PGP SIGNATURE-----
Merge tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Third batch of DT changes for 4.2" from Nicolas Ferre:
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: remove useless usb clock
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
USB: atmel: update DT bindings documentation
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iSye
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/cleanup
Merge "First batch of cleanup for 4.2" from Alexandre Belloni:
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
* tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the fixed clocks of external crystal oscillators.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[sboyd@codeaurora.org: Remove size-cells/address-cells]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Disable BeagleBone black RTC-only sleep mode because of hardare
related issues
- Fix NAND on Devkit8000
- Fix WLAN interrupt line on AM335x EVM-SK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x3Wr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Few minimal omap device tree fixes for v4.1-rc series" from Tony Lindgren:
- Disable BeagleBone black RTC-only sleep mode because of hardare
related issues
- Fix NAND on Devkit8000
- Fix WLAN interrupt line on AM335x EVM-SK
* tag 'omap-for-v4.1/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix WLAN interrupt line for AM335x EVM-SK
ARM: dts: omap3-devkit8000: Fix NAND DT node
ARM: dts: am335x-boneblack: disable RTC-only sleep
This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C6Wl
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "Berlin DT changes for v4.2" from Sebastian Hesselbarth:
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
* tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin:
Documentation: bindings: update the berlin chip and system ctrl doc
Documentation: bindings: move the Berlin clock documentation
Documentation: bindings: move the Berlin pinctrl documentation
Documentation: bindings: move the Berlin reset documentation
Documentation: bindings: update the Berlin controllers documentation
Documentation: bindings: berlin: consider our dt bindings as unstable
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
The beaglebone family of boards contain two I2C busses enabled.
The first one with a baseboard identification EEPROM and a
cape I2C bus.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this patch does the following:
1: adds DT node for fixed oscillator.
2: adds DT node entries for ov2659 sensor
3: adds remote-endpoint entry for VPFE.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This device is an industrial PC based on
AM335x SoC.
[ balbi@ti.com : updated to fit current mainline ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 wakeup takes place with iodaisy chain. enable the wakeup pin.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: tabify uart pins properly while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add voice audio card which is used for telephony on gta04 board.
gtm601 codec is UMTS modem with pcm interface which get samples from
microphone and provide data from other party side. Use simple audio card
to describe audio card.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart1 is used for connecting to wilink8 bluetooth subsystem.
add the needed muxes and definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart3 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable omap-hdq for battery fuel gauge access.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the technical reference manual for AM35xx system
controller module (SCM) PADCONFS core registers are divided in two
regions: 0x48002030..0x48002268 and 0x480025d8..0x480025fc.
First region is the same for all omap3 SoC and is described in omap3.dtsi.
The second region is the same as in omap34xx (see omap34xx.dtsi)
and omap35xx. The patch adds missing description for the second region.
This patch was tested on AM3517.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.
This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.
The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nand-ecc-opt and device-width properties to enable nand support on
Devkit8000.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: http://bugs.elinux.org/issues/143
Entering RTC-only sleep is only properly supported on early prototypes series
(pre-A6) of the BeagleBone Black. Since rev (A6A), which include all production
versions, it is not support at due to.
(rev A6) enable of the 3v3b regulator moved from LDO2 to LDO4 (3v3a)
side-effect: 3v3b rail remains on in sleep-mode (also in off-mode when battery-powered)
(rev A6A) am335x vdds supply moved from LDO3 to LDO1
side-effect: vdds remains supplied in sleep-mode
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.
Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.
Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The at91rm9200 memory controller is not simply an SDRAM controller. It also
controls the EBI (External Bus Interface), the SMC (Static Memory Controller)and
the Burst Flash Controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The i.MX27 dtb build should be controlled by CONFIG_SOC_IMX27 rather
than CONFIG_SOC_IMX31.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fixes: cb612390e5 ("ARM: dts: Only build dtb if associated Arch and/or SoC is enabled")
Cc: <stable@vger.kernel.org>
Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning
when probing the mmc1 device.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add fixed regulator for vmmc0 and attach the vmmc for it to the mmc0
node on the SAM5D3 Xplained board. This will remove the following
warning from the kernel:
atmel_mci f0000000.mmc: No vmmc regulator found
Note, atmel_defconfig will need fixed regulator support enabled if this
is to be used properly.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[use a fixed regulator instead of gpio one]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The SAM5D3 Xplained device tree is missing the vqmmc node which is
tied to 3.3V on the board. Add this to avoid the kernel warning that
there is no vqmmc node.
atmel_mci f0000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mmc1 channel is not populated on the SAM5D3 Xplained board, however
it is enabled and therefore the driver is attaching to it.
The node configuration for mmc1 is missing, so add an mmc1 node in the
device tree and set its status to disabled. Also add the vmmc and the
necessary slot configuration if this node were enabled to avoid the following
warnings from the driver:
atmel_mci f8000000.mmc: No vmmc regulator found
atmel_mci f8000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
commit 111573ccd8 ("mtd: atmel_nand: check NFC busy flag by HSMC_SR
instead of NFC cmd regs")
check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to
map NFC cmd registers to include NFCBUSY bit.
That means we only need map 0x08000000 instead of 0x10000000 for NFC
cmd regs.
This patch reduce the NFC cmd regs map for sama5d3 & sama5d4.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update the pinctrl ranges property to support pioD controller whose
mapping is not contiguous with other pio controllers. Without this
update, getting resource will fail, then pinctrl probe will fail too
because there is a missing pio controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the ADC node for the Berlin BG2Q, using the newly added
Berlin IIO ADC driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Now that the rework to have one sub-node per device in the chip and
system controllers is done, their dedicated compatible can be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With the introduction of the Berlin simple-mfd controller driver, all
drivers previously sharing the chip and system controller nodes now
have their own sub-node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With the introduction of the Berlin simple-mfd controller driver, all
drivers previously sharing the chip and system controller nodes now
have their own sub-node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With the introduction of the Berlin simple-mfd controller driver, all
drivers previously sharing the chip and system controller nodes now
have their own sub-node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Now with proper support for simple-mfd probed pinctrl driver, move
to the new soc-pinctrl and system-pinctrl nodes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Now with a proper platform driver for reset and simple-mfd, move to
the new marvell,berlin-reset node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The chip and system controller nodes will be handled by simple-mfd based
driver probing. Prepare the conversion by adding "simple-mfd" and "syscon"
compatibles to the corresponding nodes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Ux500 SOCs have a special backup RAM that needs to be
defined in the device tree.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support jpeg for exynos3250-rinato board.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add MAX98090 audio codec, I2S interface and the sound nodes
to support audio on exynos5422-odroidxu3 board. Now we can
support audio using simple-audio-card DT binding.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds nodes for hardware JPEG codec found in exynos4210
and exynos4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Extend the S3C RTC node with rtc_src clock so it could be operational.
The rtc_src clock is provided by MAX77686 (Trats2) or S2MPS11 (Arndale
Octa).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a define instead of raw number as a ID for "rtc_src" clock.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a define instead of raw number as a ID for "rtc_src" clock.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Mark "samsung,exynos3250-rtc" compatible as deprecated because it
duplicates the "samsung,s3c6410-rtc". Use "samsung,s3c6410-rtc" on
Exynos3250 and Exynos4415 boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5422 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-XU3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
On Arndale Octa the S2MPS11 RTC alarm interrupt was not handled
at all because of wrong configuration of interrupt and gpx3-2.
1. Interrupt is signaled by falling edge.
2. This GPIO line is hard-wired on the board to PVDD_APIO_1V8
through a resistor so pull-up/down must be disabled.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since commit e4b3d38088 ("phy: exynos-video-mipi: Fix regression by
adding support for PMU regmap") the syscon property is required in
samsung,s5pv210-mipi-video-phy nodes, but this DTS hadn't been updated
yet.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPLv2 only licensing on this dts makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dts under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPLv2 only licensing on this dtsi makes it very impractical
for other software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense
this dtsi under a GPLv2/X11 dual-license.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.
More information can be found on:
http://www.hitex.com/index.php?id=3212
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.
More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
NXP LPC18xx/43xx SoCs are very similar devices and should be able to
share a common base (lpc18xx.dtsi). Diffences between the devices are
put in a dtsi which is specific to that device.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVV6S0ACgkQCwYYjhRyO9W1tQCghag9/kiZ0qMJSesLBLwG7tcE
yrcAniOoTLzP6cMF+jqtuTrXwoke13JN
=OfeD
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #1)" from Gregory CLEMENT:
- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x
* tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add alias for mdio on Armada 38x
ARM: dts: dove: Add Compulab SBC-A510 to Makefile
ARM: dts: dove: Add proper support for Compulab CM-A510/SBC-A510
ARM: dts: dove: Remove Compulab CM-A510 from Makefile
ARM: dts: dove: Add internal i2c multiplexer node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KpAt
-----END PGP SIGNATURE-----
Merge tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi into next/dt
Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:
* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
ARM: bcm2835: dt: Add the mailbox to the device tree
ARM: bcm2835: dt: Fix i2c0 node name
ARM: bcm2835: dt: Use pinctrl header
ARM: bcm2835: dt: Add header file for pinctrl constants
ARM: bcm2835: dt: Add root properties for Raspberry Pi
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
The Ux500 like other Cortex-A9 SoC's has a Snoop Control
Unit (SCU) and a Watchdog in the same address range as
the local timers. Add these to the SoC device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OdRc
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
- clocks descriptions (pxa27x, pxa3xx)
- timer descriptions (pxa27x, pxa3xx)
- IPs which are embedded on the SoC
- keypad
- udc (USB client)
- power I2C
These are amongst the building blocks for future pxa device-tree board
description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GbmD
-----END PGP SIGNATURE-----
Merge tag 'pxa-dt-4.2' of https://github.com/rjarzmik/linux into next/dt
Merge "device-tree pxa update" from Robert Jarzmik:
- clocks descriptions (pxa27x, pxa3xx)
- timer descriptions (pxa27x, pxa3xx)
- IPs which are embedded on the SoC
- keypad
- udc (USB client)
- power I2C
These are amongst the building blocks for future pxa device-tree board
description.
* tag 'pxa-dt-4.2' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: add pxa-timer to pxa27x and pxa3xx
ARM: dts: pxa: add pxa27x-keypad to pxa27x
ARM: dts: pxa: add pxa27x-udc to pxa27x
ARM: dts: pxa: add clocks
ARM: dts: pxa: add pwri2c to pxa device-tree
Merge "Device Tree changes" from Florian Fainelli:
New devices:
- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
WZR-1750DHP
- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U
New peripheral support:
- Brian adds Device Tree nodes for the Broadcom NAND controller found on
BCM7xxx, BCM63138 and Cygnus SoCs
- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
BCM7xxx
- I add the Device Tree nodes and bindings documents for bringing-up secondary
CPUs and timer/syscon-reboot on BCM63138
* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC56U
ARM: BCM5301X: Add DT for Asus RT-AC68U
ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
ARM: dts: brcmstb: add nodes for SATA controller and PHY
ARM: dts: cygnus: Enable NAND support for Cygnus
ARM: bcm63138: add NAND DT support
ARM: bcm7445: add NAND to DTS
ARM: BCM5301X: Add DT for SmartRG SR400ac
ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
ARM: dts: BCM63xx: Add SMP nodes and required properties
Documentation: DT: Document SMP DT nodes and properties for BCM63138
ARM: dts: BCM63xx: Add PMB busses nodes
Documentation: DT: Add Broadcom BCM63138 PMB binding
- fix second S2R on exynos4412 based Trats2, Odroid U3 boards which
happened after enabling L2$ and caused by commit 13cfa6c4f7 ("ARM:
EXYNOS: Fix CPU idle clock down after CPU off")
And replace the soc_is_exynosxxx() macro with of_compatible_xxx
- fix dereference of ERR_PTR of of_genpd_get_from_provider()
- fix suspend problem on old DT machines to skip the initialization
suspend and caused by commit 8b283c0254 ("ARM: exynos4/5: convert
pmu wakeup to stacked domains")
- add keep-power-in-suspend for Peach Boards to support S2R and has
been missed in previous pull-request for fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=r1wn
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung 2nd fixes for v4.1" from Kukjin Kim:
- fix second S2R on exynos4412 based Trats2, Odroid U3 boards which
happened after enabling L2$ and caused by commit 13cfa6c4f7 ("ARM:
EXYNOS: Fix CPU idle clock down after CPU off")
And replace the soc_is_exynosxxx() macro with of_compatible_xxx
- fix dereference of ERR_PTR of of_genpd_get_from_provider()
- fix suspend problem on old DT machines to skip the initialization
suspend and caused by commit 8b283c0254 ("ARM: exynos4/5: convert
pmu wakeup to stacked domains")
- add keep-power-in-suspend for Peach Boards to support S2R and has
been missed in previous pull-request for fixes
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Use of_machine_is_compatible instead of soc_is_exynos4
ARM: EXYNOS: Fix failed second suspend on Exynos4
ARM: EXYNOS: Fix dereference of ERR_PTR returned by of_genpd_get_from_provider
ARM: EXYNOS: Don't try to initialize suspend on old DT
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for Peach Boards
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
Add clock-names to CuBox Si5351 clk generator
Add dts entries in the MAINTAINERS file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVV6IwACgkQCwYYjhRyO9V2iACgi038BpoDW4Nf4Ivt+6eGzGeB
2GAAoKnvitRZBNyFsWiWtvo/Yl7Rgiol
=MCEb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1-2' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.1 (part 2)" from Gregory CLEMENT:
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
Add clock-names to CuBox Si5351 clk generator
Add dts entries in the MAINTAINERS file
* tag 'mvebu-fixes-4.1-2' of git://git.infradead.org/linux-mvebu:
MAINTAINERS: Add dts entries for some of the Marvell SoCs
ARM: dove: Add clock-names to CuBox Si5351 clk generator
ARM: mvebu: Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288-evb files to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Chris Zhong<zyw@rock-chips.com>
Acked-by: Roger Chen <roger.chen@rock-chips.com>
Acked-by: Yunzhi Li <lyz@rock-chips.com>
on behalf of Rockchip
Acked-by: Eddie Cai <eddie.cai@rock-chips.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
Acked-by: Lin Huang <hl@rock-chips.com>
Acked-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Jianqun Xu<jay.xu@rock-chips.com>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Roger Chen <roger.chen@rock-chips.com>
Acked-by: Yunzhi Li <lyz@rock-chips.com>
on behalf of Rockchip
Acked-by: Eddie Cai <eddie.cai@rock-chips.com>
This patch fixes a regression where serial is enabled by the first
(board) DTSI, then disabled by the second (SoC) file. To enable
serial and keep it enabled, we need to include the file which enables
it last.
Reported-by: LAVA [via Peter Griffin <peter.griffin@linaro.org>]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The SI unit of frequency is Hertz, named after Heinrich Hertz, and is
given the symbol "Hz" to denote this. "hz" is not the unit of frequency,
and is in fact meaningless.
Fix arch/arm to correctly use "Hz", thereby acknowledging Heinrich Hertz'
contribution to the modern world.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There exists a tiny MMU, configurable only by the VC (running the
closed firmware), which maps from the ARM's physical addresses to bus
addresses. These bus addresses determine the caching behavior in the
VC's L1/L2 (note: separate from the ARM's L1/L2) according to the top
2 bits. The bits in the bus address mean:
From the VideoCore processor:
0x0... L1 and L2 cache allocating and coherent
0x4... L1 non-allocating, but coherent. L2 allocating and coherent
0x8... L1 non-allocating, but coherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
From the GPU peripherals (note: all peripherals bypass the L1
cache. The ARM will see this view once through the VC MMU):
0x0... Do not use
0x4... L1 non-allocating, and incoherent. L2 allocating and coherent.
0x8... L1 non-allocating, and incoherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent
The 2835 firmware always configures the MMU to turn ARM physical
addresses with 0x0 top bits to 0x4, meaning present in L2 but
incoherent with L1. However, any bus addresses we were generating in
the kernel to be passed to a device had 0x0 bits. That would be a
reserved (possibly totally incoherent) value if sent to a GPU
peripheral like USB, or L1 allocating if sent to the VC (like a
firmware property request). By setting dma-ranges, all of the devices
below it get a dev->dma_pfn_offset, so that dma_alloc_coherent() and
friends return addresses with 0x4 bits and avoid cache incoherency.
This matches the behavior in the downstream 2708 kernel (see
BUS_OFFSET in arch/arm/mach-bcm2708/include/mach/memory.h).
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Device tree node names should contain the node's reg property address value.
The i2c0 node was apparently forgotten in commit 25b2f1bd0b (ARM: bcm2835:
node name unit address cleanup).
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to the imx27 documentation, fec has a 4 Kbyte
memory space map. Moreover, the actual 16 Kbyte mapping
overlaps the SCC (Security Controller) memory register
space. So, we reduce the memory register space to 4 Kbyte.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9f0749e3eb ("ARM i.MX27: Add devicetree support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3188-radxarock.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3066a-bqcurie2.dts to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3288-thermal.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Caesar Wang <caesar.wang@rock-chips.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3188.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3066a.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
GPLv2-only devicetrees make reuse difficult for software components licensed
under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary uses,
so relicense the rk3xxx.dtsi to this combination.
CCs were aquired by git shortlog -sne so it should've hopefully catched
every contributor.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Julien Chauveau <chauveau.julien@gmail.com>
Add a "brcm,bcm6328-timer" and "syscon-reboot" nodes to allow the
generic syscon-reboot driver to reset a BCM63138 SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable NAND support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update bcm63138.dtsi with the following:
- enable-method for both CPU nodes
- brcm,bcm63138-bootlut node
- resets properties to point to the correct PMB controller to release
the secondary CPU from reset
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the two BCM63138 PMB busses nodes found on this System-on-a-Chip as
described in their corresponding binding document.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Contains a couple of fixes and additions to device tree files. The most
notable change is a fix for a misapplied patch that was only exposed by
a recent change in the regulator subsystem that caused USB to break on
Tegra124 recently.
Other than that there are a more or less random assortment of additions
to enable various features on a couple of boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8R5I
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Devicetree changes for v4.2-rc1" from Thierry Reding:
Contains a couple of fixes and additions to device tree files. The most
notable change is a fix for a misapplied patch that was only exposed by
a recent change in the regulator subsystem that caused USB to break on
Tegra124 recently.
Other than that there are a more or less random assortment of additions
to enable various features on a couple of boards.
* tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Fix hda2codec_2x clock and reset names
ARM: tegra: Add Tegra30 HDA support
ARM: tegra: Cardhu device-tree comment spelling fix
ARM: tegra: venice2: Set min-/max-microvolt for VDD_LED supply
ARM: tegra: venice2: Mark eMMC as non-removable
ARM: tegra: jetson-tk1: Enable HDA support
ARM: tegra: Add missing HDMI +5V regulator
ARM: tegra: cardhu: Add power and volume keys
ARM: tegra: Correct which USB controller has the UTMI pad registers
Just a couple of trivial cleanups such as a typofix and conversion of
hexadecimal numbers to all lower-case in DTS files for consistency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OrUc
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
Merge "ARM: tegra: Cleanup patches for v4.2-rc1" from Thierry Reding:
Just a couple of trivial cleanups such as a typofix and conversion of
hexadecimal numbers to all lower-case in DTS files for consistency.
* tag 'tegra-for-4.2-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Fix typo (reset -> rest) in comment
ARM: tegra: Use lower-case hexadecimal digits
- Add a DTS node for the A9 SCU
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=23ne
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Merge "SoCFPGA update for v4.2 part 2" from Dinh Nguyen:
- Add a DTS node for the A9 SCU
* tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: add the a9-scu node
the Cortex-A12 HW PMU on the rk3288 and the tsadc on some more rk3288
boards, as well as some usb properties and marking the radxarock pmic
as system-power-controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVU2Y0AAoJEPOmecmc0R2BXCQIAIV6yQP+f6ACIPJEVRk8yD3W
YyJ/mXgrSD/RaaFYnEO3PPVC8TibVI6a7SIoa4y92g0LW7VYn7UQY1wzlrt3rzR5
rY71uB/Ew0yQBJe1rsw+Sn7couG9U/g3YB/guJmFfO2rS9xn6wICKcLxYNaIp9sb
WOwzNlpWwpejCdYLzxw9BP0qxFRE2ZlxoF96VB+j5s+IcnvKGGo3twYqtyN5YEjK
dB7Bbnq6n9VWgYMkuijxyQ00skUNUb+7ciHSO4pksPtuSa4K+GsqjkTu37nkBPmn
t53c+M93WuI5hplFRM3UwXKH6ELqhEuq0GN4dPzRD5VBWcWYOMXl8AmhfOlR6cU=
=39uK
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: dts changes for 4.2" from Heiko Stuebner:
Some misc improvements defining additional supply regulators, enabling
the Cortex-A12 HW PMU on the rk3288 and the tsadc on some more rk3288
boards, as well as some usb properties and marking the radxarock pmic
as system-power-controller.
* tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add system-power-controller to act8846 on radxarock
ARM: dts: rockchip: add properties for dwc2 usb otg controller
ARM: dts: rockchip: enable tsadc on rk3288 boards
ARM: dts: rockchip: add act8846 supplies on rk3288-firefly
ARM: dts: rockchip: Specify VMMC and VQMMC on rk3288-evb
ARM: dts: rockchip: Enable Cortex-A12 HW PMU events on rk3288
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+QE+
-----END PGP SIGNATURE-----
Merge tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add the sensors to the STUIB board
ARM: ux500: assign the sensor trigger IRQs
ARM: ux500: fix lsm303dlh magnetometer compat string
ARM: ux500: add CoreSight blocks to DTS file
ARM: ux500: define CPU topology
This adds the device tree data for the LIS331DL and the
AK8974 magnetometer to the STUIB board device tree include
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST sensors on the Ux500 boards were not utilizing the IRQs
for data ready sample triggers. Enable this by assigning the
right GPIO lines and interrupt lines (when the GPIO lines are
used for IRQs) to the accelerometer, gyro and magnetometer
sensors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The magnetometer found on the Ux500 TVK and Snowball boards
is a LSM303DLH not a LSM303DLM, small differences but still
different. Put in the right compatible strings and things start
working smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers all the CoreSight blocks on the DB8500 SoC:
each core has a PTM (v1.0, r1p0-00rel0) connected, both connected
to a funnel (DK-TM908-r0p1-00rel0) which in turn connects to a
replicator (DM-TM909-r0p1-00rel0). The replicator has two outputs,
port 0 to a TPIU interface and port 1 to an ETB
(DK-TM907-r0p3-00rel0). The CoreSight blocks are all clocked by
the APEATCLK from the PRCMU and their AHB interconnect is clocked
from a separate clock called APETRACECLK.
The SoC also has a CTI/CTM block which can be added later as we
have upstream support in the CoreSight subsystem.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.
Here we are enabling PMU IRQs on both channels.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This is ARM's generic Performance Monitoring Unit.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.
Here we are enabling PMU IRQs on both channels.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This is ARM's generic Performance Monitoring Unit.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
All the infrastructure is now in place for ST's PWM controller. This
patch takes the final step and enables the IP on the 2020 Rev-E
development platform.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Supply top level nodes for the STiH416 based development boards.
The Pinctrl configuration has already been applied, so the only
missing piece of the DT puzzle is for a board's DTB to enable
the nodes.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Supply the Pinctrl configuration to enable PWM{0,1} lines on STiH416
based development boards.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Supply top level nodes for the STiH407 based development boards.
The Pinctrl configuration has already been applied, so the only
missing piece of the DT puzzle is for a board's DTB to enable
the nodes.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Each pxa has an embedded OS Timers IP. The kernel cannot work without a
valid clocksource, and this adds the OS Timers to the pxa device-tree
description.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add clocks to the IPs already described in the pxa device-tree
files. There are more clocks in the clock tree than IPs described in the
current pxa device-tree.
This patch ensures that :
- the current description is correct
- the clocks are actually claimed, so that clock framework doesn't
disable them automatically (unused clocks shutdown)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
pxa27x variant has 2 I2C busses on the SoC :
- the casual I2C
- the power I2C, normally driving power regulators, and capable of
receiving orders on core frequency modifications
Add the missing pwri2c to pxa27x description.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The act8846 is the main pmic and system-power-controller on radxarock boards,
so add the necessary property.
Signed-off-by: Michael Niewoehner <mniewoeh@stud.hs-offenburg.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
HS400 timing values are added for exynos5422-odroidxu3 board.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6TQo
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT additions for 4.1, take 1" from Maxime Ripard:
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
* tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (84 commits)
ARM: sunxi: dt: Split the SPI pinctrl groups
ARM: sunxi: dt: Fix whitespace errors
ARM: sunxi: DT: Fix lines over 80 characters
ARM: sunxi: dt: Remove the FSF address
ARM: sunxi: dts: split IR pins for A10 and A20
ARM: sun7i: dt: Add new MK808C device
ARM: dts: sun6i: Set PLL6 as parent to AHB1 clock in AHB1 clock node
ARM: dts: sunxi: Update ahb clocks for sun5i and sun7i
ARM: dts: sun7i: Add dts file for the Jesurun Q5 top set box
ARM: dts: sun5i: Enable touchscreen on Utoo P66
ARM: dts: sun7i: Add dts file for the Orangepi mini SBC
ARM: dts: sun7i: Add dts file for the Orangepi SBC
ARM: dts: sun7i: Add A20 SRAM and SRAM controller
ARM: dts: sun5i: Add A13 and A10s SRAM and SRAM controller
ARM: dts: sun4i: Add A10 SRAM and SRAM controller
ARM: dts: sun5i: Add broken-hpi property for Utoo-P66 eMMC
ARM: sun8i: dt: Enable A23 SMP support
ARM: dts: sun6i: Add cpu thermal zones to dtsi
ARM: dts: sun6i: Add cpu clock reference and operating points to dtsi
ARM: sunxi: DT: Add stdout-path property
...
Highlights:
-----------
- Add DT nodes for SSC on STiH407 family
- Add DT nodes for SD/MMC on STiH407 & STiH418
- Add DT node for LPC on STiH407
- Add Sata DT nodes for STiH407
- Fix PIO3 & PIO35 pins retiming on STiH407
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fWhS
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt
Pull "STi DT updates for v4.2, round 1." from Maxime Coquelin:
Highlights:
-----------
- Add DT nodes for SSC on STiH407 family
- Add DT nodes for SD/MMC on STiH407 & STiH418
- Add DT node for LPC on STiH407
- Add Sata DT nodes for STiH407
- Fix PIO3 & PIO35 pins retiming on STiH407
* tag 'sti-dt-for-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: DT: STi: STiH407: Add sata DT nodes.
ARM: STi: DT: STiH407: Fix retime pin mask for PIO5 and PIO35
ARM: STi: DT: STiH407: Add Device Tree node for the LPC
mfd: dt-bindings: Provide human readable defines for LPC mode choosing
ARM: STi: DT: STiH418: Add dt nodes for sdhci and emmc.
ARM: STi: DT: STiH407: Add dt nodes for sdhci and emmc.
ARM: sti: Provide DT nodes for SBC SSC[0..2]
ARM: sti: Provide DT nodes for SSC[0..4]
Commit 9fd85eb502 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-ca15_a7(a.k.a TC2) device tree.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9fd85eb502 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-v2p-ca9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit d9d1f3e2d7 ("ARM: l2c: check that DT files specify the required
"cache-unified" property") mandates to specify this required property.
Without this property, we get this boot warning:
"L2C: device tree omits to specify unified cache"
This patch adds "cache-unified" property to L2 cache node in vexpress
CA9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a fix for a bug that was introduced a couple of months ago
by a patch that git misapplied because of a lack of context.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8e1C
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.1-fixes-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
Merge "ARM: tegra: Device tree fixes for v4.1-rc3" from Thierry Reding:
This contains a fix for a bug that was introduced a couple of months ago
by a patch that git misapplied because of a lack of context.
* tag 'tegra-for-4.1-fixes-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct which USB controller has the UTMI pad registers
This patch adds DMA properties to the HSUSB node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds DMA properties to the HSUSB node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add all the clock nodes for the Arria10 platform. At the same time, update
the peripherals with their respective clocks property.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add the l4_sys_free_clk node
Add tx-fifo-depth and rx-fifo-depth devicetree properties for socfpga
stmmac. These devicetree properties will be used to configure certain
features of the stmmac on the socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add multicast-filter-bins and perfect-filter-entries configuration properties
to the socfpga devicetree for the Arria 10 socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The CIU(Card Interface Unit) get its clock from the sdmmc_clk_divided clock
which is used to clock the card. The sdmmc_clk_divided clock is the sdmmc_clk
passed through a fixed divider of 4. This patch adds the sdmmc_clk_divided
node and makes the sdmmc_clk it's parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: renamed ciu_clk to sdmmc_clk_divided
Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.
Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Arria10 devkit is using UART1 for the debug uart port. Remove
unused aliases.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add removal of unused aliases
Add status = "disabled" in the base DTSI for Arria10. The SDMMC and uart
nodes should be enabled in the appropriate board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds the DTS bindings for the adxl34x digital
accelerometer.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Si5351 clock generator on CuBox uses XTAL as clock reference, name the
clock phandle accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
With reworked device tree files for Compulab CM-A510 SoM and SBC-A510
base board, now add the correspoding board file to Makefile again.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Existing dts file for Compulab CM-A510 was very limited due to missing
hardware. Now that we actually found somebody with that board, properly
rework it to provide a CoM/SoM include and a board file for Compulab's
SBC-A510.
Both the CM-A510 SoM and the SBC-A510 can be configured with different
options, so we only enable a minimum set of options. The actual board
configuration will have to be set by either the bootloader or user.
Although functionally not required, repeat even disabled nodes again
to increse their visibility in the dtsi/dts files.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Gabriel Dobato <dobatog@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Prior reworking Dove based Compulab CM-A510 device tree, remove it
from the compiled device tree files.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This adds a i2c-mux-pinctrl node to dove.dtsi for the internal i2c
mux found on Dove SoCs. Up to now, we had no board using any of the
two additional i2c busses, so make sure the change does not break
any existing boards.
Therefore, we rename the i2c-controller node label to "i2c" and
enable it by default. Also, the dedicated sub-bus (now "i2c0") is
enabled by default. The two optional sub-busses require additional
external pin-muxing, so disable them by default.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The clock-frequency property became obsolete since the rework of the main
clock driver in 3.16 (see commit 27cb1c2083).
It now get and uses the clock-frequency from the main_xtal node.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DT file for Kizbox 2 board.
This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DT file for Kizbox mini board.
This board is based on Atmel's AT91SAM9G25 SoC.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Integrators and the RealView use simple MFD devices with register bit
LEDs as subnodes, update these to use the "simple-mfd" compatible property
so that subdevices get spawned from the MFD nexi.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note that from now on any of the pfc8575 gpio keys will wake up the
system, as the pfc8575 cannot mask individual interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl512s is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl008k is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl512s is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl008k is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl512s is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controller irqc0 to the IRQC module clock, so it
can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the external IRQ controllers irqc0 and irqc1 to the IRQC module
clock, so they can be power managed using that clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: corrected typo in changelog to refer to r8a73a4]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- fixes commit ea08de16eb ("ARM: dts: Add DISP1 power
domain for exynos5420") which causes 'unhandled fault:
imprecise external abort' error when PD turned off.
: make DP a consumer of DISP1 power domain
- fixes 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards.
: add 'rtc_src' clock to rtc node for source clock of rtc
- fixes typo for 'cpu-crit-0' trip point on exynos5420/5440
- fixes S2R failure on exynos5250-snow due to card power of
Marvell WiFi driver (suspend/resume)
: add keep-power-in-susped to WiFi SDIO node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YBxq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
Pull samsung fixes from Kukjin Kim:
"Here is Samsung fixes for v4.1. Since I've missed to send this via
arm-soc tree before v4.1-rc3, so I'm sending this to you directly
- fix commit ea08de16eb ("ARM: dts: Add DISP1 power domain for
exynos5420") which causes 'unhandled fault: imprecise external
abort' error when PD turned off. ("make DP a consumer of DISP1
power domain")
- fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
'rtc_src' clock to rtc node for source clock of rtc")
- fix typo for 'cpu-crit-0' trip point on exynos5420/5440
- fix S2R failure on exynos5250-snow due to card power of Marvell
WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
SDIO node")"
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
The pinctrl groups for SPI until now were also adding the chip selects in
the SPI pinctrl group.
This was causing a few issues, since a board was forced to use a random
number of chipselects, even though it might use one of these chip selects
for another pin.
The number of chipselects defined was also not the same from one group to
another because of different needs at the time these groups have been
introduced, resulting in no clear view from the board DTS on what exactly
is being muxed, which even might change in the future.
Solve this by creating different pinctrl groups for the chipselects and the
standard SPI pins (CLK, MOSI and MISO) so that we fix both issues.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines (probably copy pasted) have an indentation mixing tabs and
spaces that triggers a checkpatch warning.
Fix those, and while we're at it, fix the space-indented sections.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines in our DTSIs are over the 80 characters limit, making
checkpatch complain about that.
If possible (and relevant), wrap these lines to 80 characters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the RGB-LED on XU3 as 3 gpio-leds.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds gpio for detecting presence of MMC card.
It fixes issue with kernel hang when MMC card is missing.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds pinctrl configuration for using configuring gpx3-2 as an
external interrupt from max77686. Though max77686 RTC is enabled and gets
probed by default, it doesnt work as its unable to get interrupt.
This patch makes max77686 RTC work and also configures it as wakeup source.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
[pankaj.dubey: resubmitted after rebasing to latest kgene tree]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
BSYM() was invented to allow us to work around a problem with the
assembler, where local symbols resolved by the assembler for the 'adr'
instruction did not take account of their ISA.
Since we don't want BSYM() used elsewhere, replace BSYM() with a new
macro 'badr', which is like the 'adr' pseudo-op, but with the BSYM()
mechanics integrated into it. This ensures that the BSYM()-ification
is only used in conjunction with 'adr'.
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
add the device tree binding for the HiSilicon hip04 ethernet controller
based on Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds dts support for NAND flash controller of Hisilicon Soc Hip04.
Changes in v3:
- Change E-mail address in signed-off-by to "wangzhou1@hisilicon.com"
Changes in v2:
- Base on v3.19-rc1
- Use nand-ecc-strength, nand-ecc-step-size to replace hisi,nand-ecc-bits
Changes in v1:
- Move partition and other board related information into board dts file:
hip04-d01.dts
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Hisilicon Soc hip04 has four GPIO controllers, each one has 32
GPIOs and can be configured to be an interrupt controller.The GPIO
controllers are compatible with the snps,dw-apb-gpio driver.
This patch add the corresponding device tree nodes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YtL
-----END PGP SIGNATURE-----
Merge tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
Merge "Ux500 fixes" from Linus Walleij:
This fixes an MMC/SD configuration issue present for some time
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
* tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable GPIO regulator for SD-card for snowball
ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
ARM: ux500: Move GPIO regulator for SD-card into board DTSs
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
Disable the unused internal RTC in the dts of the OpenBlock AX3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVDtLIACgkQCwYYjhRyO9WCiwCfTBYFFDMZxK/W9qLdhU8mj/iD
tDQAn3TDsfWEIHm+c6DeZqj35Q74yPGA
=Gggv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fix for 4.1" from Gregory CLEMENT:
Disable the unused internal RTC in the dts of the OpenBlock AX3
* tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp-openblocks-ax3-4: Disable internal RTC
The USB3 controller is present on the b2199 board, so enable
it in the board specific DT file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
STiH418 miphy28lp port0/1 need the oscillator clock configured in the same way
as on STiH407/STiH410 platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The USB3 controller is present on both variants of the b2120 board so
enable the controller in the generic stihxxx-b2120.dtsi file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Now that both usb2 and usb3 phy drivers, and also the ST dwc3 glue code
are all present upstream, we can add the dwc3 DT node and have a working
usb3 controller on stih407-b2120 and stih410-b2020.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Ths picophyreset is incorrectly defined, which stops the usb2 phy being
taken out of reset.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The binding documentation says that these should be named hda2codec_2x
but the DTSI names them hdacodec_2x.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
[treding@nvidia.com: add a brief commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the HDA controller found on Tegra30.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The word "sticker" was misspelled as "stciker". Fix it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
[treding@nvidia.com: add a brief commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
eMMC is soldered on to the board, and as such isn't removable. Mark it
as non-removable so that operating systems can treat it appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: Matt Gessner <Matt.Gessner@windriver.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gregory CLEMENT