Allow a process bound to a VRF to connect to a linklocal address.
Currently, this fails because of a mismatch between the scope of the
linklocal address and the sk_bound_dev_if inherited by the VRF binding:
$ ssh -6 fe80::70b8:cff:fedd:ead8%eth1
ssh: connect to host fe80::70b8:cff:fedd:ead8%eth1 port 22: Invalid argument
Relax the scope check to allow the socket to be bound to the same L3
device as the scope id.
This makes ipv6 linklocal consistent with other relaxed checks enabled
by commits 1ff23beebd ("net: l3mdev: Allow send on enslaved interface")
and 7bb387c5ab ("net: Allow IP_MULTICAST_IF to set index to L3 slave").
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, IPv6 deletes nexthops from a multipath route when the
nexthop device is put administratively down. This differs from IPv4
where the nexthops are kept, but marked with the RTNH_F_DEAD flag. A
multipath route is flushed when all of its nexthops become dead.
Align IPv6 with IPv4 and have it conform to the same guidelines.
In case the multipath route needs to be flushed, its siblings are
flushed one by one. Otherwise, the nexthops are marked with the
appropriate flags and the tree walker is instructed to skip all the
siblings.
As explained in previous patches, care is taken to update the sernum of
the affected tree nodes, so as to prevent the use of wrong dst entries.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to allow dead routes to remain in the FIB tree
in certain situations.
When this happens we need to be sure to bump the sernum of the nodes
where these are stored so that potential copies cached in sockets are
invalidated.
The function that performs this update assumes the table lock is not
taken when it is invoked, but that will not be the case when it is
invoked by the tree walker.
Have the function assume the lock is taken and make the single caller
take the lock itself.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to allow dead routes to stay in the FIB tree (e.g., when
they are part of a multipath route, directly connected route with no
carrier) and revive them when their nexthop device gains carrier or when
it is put administratively up.
This is equivalent to the addition of the route to the FIB tree and we
should therefore take care of updating the sernum of all the parent
nodes of the node where the route is stored. Otherwise, we risk sockets
caching and using sub-optimal dst entries.
Export the function that performs the above, so that it could be invoked
from fib6_ifup() later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous patch, fib6_ifdown() needs to consider the
state of all the sibling routes when a multipath route is traversed.
This is done by evaluating all the siblings when the first sibling in a
multipath route is traversed. If the multipath route does not need to be
flushed (e.g., not all siblings are dead), then we should just skip the
multipath route as our work is done.
Have the tree walker jump to the last sibling when it is determined that
the multipath route needs to be skipped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the RTNH_F_DEAD flag was only reported in route dump when
the 'ignore_routes_with_linkdown' sysctl was set. This is expected as
dead routes were flushed otherwise.
The reliance on this sysctl is going to be removed, so we need to report
the flag regardless of the sysctl's value.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, dead routes are only present in the routing tables in case
the 'ignore_routes_with_linkdown' sysctl is set. Otherwise, they are
flushed.
Subsequent patches are going to remove the reliance on this sysctl and
make IPv6 more consistent with IPv4.
Before this is done, we need to make sure dead routes are skipped during
route lookup, so as to not cause packet loss.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to previous patch, there is no need to check for the carrier of
the nexthop device when dumping the route and we can instead check for
the presence of the RTNH_F_LINKDOWN flag.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the RTNH_F_LINKDOWN flag is set in nexthops, we can avoid the
need to dereference the nexthop device and check its carrier and instead
check for the presence of the flag.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is valid to install routes with a nexthop device that does not have a
carrier, so we need to make sure they're marked accordingly.
As explained in the previous patch, host and anycast routes are never
marked with the 'linkdown' flag.
Note that reject routes are unaffected, as these use the loopback device
which always has a carrier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, when the carrier of a netdev changes we should toggle
the 'linkdown' flag on all the nexthops using it as their nexthop
device.
This will later allow us to test for the presence of this flag during
route lookup and dump.
Up until commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") host and anycast routes used the loopback netdev
as their nexthop device and thus were not marked with the 'linkdown'
flag. The patch preserves this behavior and allows one to ping the local
address even when the nexthop device does not have a carrier and the
'ignore_routes_with_linkdown' sysctl is set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make IPv6 more in line with IPv4 we need to be able to respond
differently to different netdev events. For example, when a netdev is
unregistered all the routes using it as their nexthop device should be
flushed, whereas when the netdev's carrier changes only the 'linkdown'
flag should be toggled.
Currently, this is not possible, as the function that traverses the
routing tables is not aware of the triggering event.
Propagate the triggering event down, so that it could be used in later
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch marked nexthops with the 'dead' and 'linkdown' flags.
Clear these flags when the netdev comes back up.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is put administratively down or unregistered all the
nexthops using it as their nexthop device should be marked with the
'dead' and 'linkdown' flags.
Currently, when a route is dumped its nexthop device is tested and the
flags are set accordingly. A similar check is performed during route
lookup.
Instead, we can simply mark the nexthops based on netdev events and
avoid checking the netdev's state during route dump and lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By the time fib6_net_exit() is executed all the netdevs in the namespace
have been either unregistered or pushed back to the default namespace.
That is because pernet subsys operations are always ordered before
pernet device operations and therefore invoked after them during
namespace dismantle.
Thus, all the routing tables in the namespace are empty by the time
fib6_net_exit() is invoked and the call to rt6_ifdown() can be removed.
This allows us to simplify the condition in fib6_ifdown() as it's only
ever called with an actual netdev.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-12-22
1) Separate ESP handling from segmentation for GRO packets.
This unifies the IPsec GSO and non GSO codepath.
2) Add asynchronous callbacks for xfrm on layer 2. This
adds the necessary infrastructure to core networking.
3) Allow to use the layer2 IPsec GSO codepath for software
crypto, all infrastructure is there now.
4) Also allow IPsec GSO with software crypto for local sockets.
5) Don't require synchronous crypto fallback on IPsec offloading,
it is not needed anymore.
6) Check for xdo_dev_state_free and only call it if implemented.
From Shannon Nelson.
7) Check for the required add and delete functions when a driver
registers xdo_dev_ops. From Shannon Nelson.
8) Define xfrmdev_ops only with offload config.
From Shannon Nelson.
9) Update the xfrm stats documentation.
From Shannon Nelson.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-12-22
1) Check for valid id proto in validate_tmpl(), otherwise
we may trigger a warning in xfrm_state_fini().
From Cong Wang.
2) Fix a typo on XFRMA_OUTPUT_MARK policy attribute.
From Michal Kubecek.
3) Verify the state is valid when encap_type < 0,
otherwise we may crash on IPsec GRO .
From Aviv Heller.
4) Fix stack-out-of-bounds read on socket policy lookup.
We access the flowi of the wrong address family in the
IPv4 mapped IPv6 case, fix this by catching address
family missmatches before we do the lookup.
5) fix xfrm_do_migrate() with AEAD to copy the geniv
field too. Otherwise the state is not fully initialized
and migration fails. From Antony Antony.
6) Fix stack-out-of-bounds with misconfigured transport
mode policies. Our policy template validation is not
strict enough. It is possible to configure policies
with transport mode template where the address family
of the template does not match the selectors address
family. Fix this by refusing such a configuration,
address family can not change on transport mode.
7) Fix a policy reference leak when reusing pcpu xdst
entry. From Florian Westphal.
8) Reinject transport-mode packets through tasklet,
otherwise it is possible to reate a recursion
loop. From Herbert Xu.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'md' is allocated from 'tun_dst = ip_tun_rx_dst' and
since we've checked 'tun_dst', 'md' will never be NULL.
The patch removes it at both ipv4 and ipv6 erspan.
Fixes: afb4c97d90 ("ip6_gre: fix potential memory leak in ip6erspan_rcv")
Fixes: 50670b6ee9 ("ip_gre: fix potential memory leak in erspan_rcv")
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SNAT modifies the source address the resulting packet might match
an IPsec policy, reinject the packet if that's the case.
The exact same thing is already done for IPv4.
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip6gre is created using ioctl, its features, such as
scatter-gather, GSO and tx-checksumming will be turned off:
# ip -f inet6 tunnel add gre6 mode ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: off
scatter-gather: off
tcp-segmentation-offload: off
generic-segmentation-offload: off [requested on]
But when netlink is used, they will be enabled:
# ip link add gre6 type ip6gre remote fd00::1
# ethtool -k gre6 (truncated output)
tx-checksumming: on
scatter-gather: on
tcp-segmentation-offload: on
generic-segmentation-offload: on
This results in a loss of performance when gre6 is created via ioctl.
The issue was found with LTP/gre tests.
Fix it by moving the setup of device features to a separate function
and invoke it with ndo_init callback because both netlink and ioctl
will eventually call it via register_netdevice():
register_netdevice()
- ndo_init() callback -> ip6gre_tunnel_init() or ip6gre_tap_init()
- ip6gre_tunnel_init_common()
- ip6gre_tnl_init_features()
The moved code also contains two minor style fixes:
* removed needless tab from GRE6_FEATURES on NETIF_F_HIGHDMA line.
* fixed the issue reported by checkpatch: "Unnecessary parentheses around
'nt->encap.type == TUNNEL_ENCAP_NONE'"
Fixes: ac4eb009e4 ("ip6gre: Add support for basic offloads offloads excluding GSO")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl.ip6.auto_flowlabels is default 1. In our hosts, we set it to 2.
If sockopt doesn't set autoflowlabel, outcome packets from the hosts are
supposed to not include flowlabel. This is true for normal packet, but
not for reset packet.
The reason is ipv6_pinfo.autoflowlabel is set in sock creation. Later if
we change sysctl.ip6.auto_flowlabels, the ipv6_pinfo.autoflowlabel isn't
changed, so the sock will keep the old behavior in terms of auto
flowlabel. Reset packet is suffering from this problem, because reset
packet is sent from a special control socket, which is created at boot
time. Since sysctl.ipv6.auto_flowlabels is 1 by default, the control
socket will always have its ipv6_pinfo.autoflowlabel set, even after
user set sysctl.ipv6.auto_flowlabels to 1, so reset packset will always
have flowlabel. Normal sock created before sysctl setting suffers from
the same issue. We can't even turn off autoflowlabel unless we kill all
socks in the hosts.
To fix this, if IPV6_AUTOFLOWLABEL sockopt is used, we use the
autoflowlabel setting from user, otherwise we always call
ip6_default_np_autolabel() which has the new settings of sysctl.
Note, this changes behavior a little bit. Before commit 42240901f7
(ipv6: Implement different admin modes for automatic flow labels), the
autoflowlabel behavior of a sock isn't sticky, eg, if sysctl changes,
existing connection will change autoflowlabel behavior. After that
commit, autoflowlabel behavior is sticky in the whole life of the sock.
With this patch, the behavior isn't sticky again.
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <tom@quantonium.net>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, parameters such as oif and source address are not taken into
account during fibmatch lookup. Example (IPv4 for reference) before
patch:
$ ip -4 route show
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
198.51.100.0/24 dev dummy1 proto kernel scope link src 198.51.100.1
$ ip -6 route show
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy0 proto kernel metric 256 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
$ ip -4 route get fibmatch 192.0.2.2 oif dummy0
192.0.2.0/24 dev dummy0 proto kernel scope link src 192.0.2.1
$ ip -4 route get fibmatch 192.0.2.2 oif dummy1
RTNETLINK answers: No route to host
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
After:
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy0
2001:db8:1::/64 dev dummy0 proto kernel metric 256 pref medium
$ ip -6 route get fibmatch 2001:db8:1::2 oif dummy1
RTNETLINK answers: Network is unreachable
The problem stems from the fact that the necessary route lookup flags
are not set based on these parameters.
Instead of duplicating the same logic for fibmatch, we can simply
resolve the original route from its copy and dump it instead.
Fixes: 18c3a61c42 ("net: ipv6: RTM_GETROUTE: return matched fib result when requested")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_state_load is only used by AF_INET/AF_INET6, so rename it to
inet_sk_state_load and move it into inet_sock.h.
sk_state_store is removed as it is not used any more.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If md is NULL, tun_dst must be freed, otherwise it will cause memory
leak.
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ipv4 code, when ip6erspan_rcv call return PACKET_REJECT, we
should call icmpv6_send to send icmp unreachable message in error path.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Acked-by: William Tu <u9012063@gmail.com>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() can change skb->data, so we need to load ipv6h/ershdr at
the right place.
Fixes: 5a963eb61b ("ip6_gre: Add ERSPAN native tunnel support")
Cc: William Tu <u9012063@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LTP/udp6_ipsec_vti tests fail when sending large UDP datagrams over
ip6_vti that require fragmentation and the underlying device has an
MTU smaller than 1500 plus some extra space for headers. This happens
because ip6_vti, by default, sets MTU to ETH_DATA_LEN and not updating
it depending on a destination address or link parameter. Further
attempts to send UDP packets may succeed because pmtu gets updated on
ICMPV6_PKT_TOOBIG in vti6_err().
In case the lower device has larger MTU size, e.g. 9000, ip6_vti works
but not using the possible maximum size, output packets have 1500 limit.
The above cases require manual MTU setup after ip6_vti creation. However
ip_vti already updates MTU based on lower device with ip_tunnel_bind_dev().
Here is the example when the lower device MTU is set to 9000:
# ip a sh ltp_ns_veth2
ltp_ns_veth2@if7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 ...
inet 10.0.0.2/24 scope global ltp_ns_veth2
inet6 fd00::2/64 scope global
# ip li add vti6 type vti6 local fd00::2 remote fd00::1
# ip li show vti6
vti6@NONE: <POINTOPOINT,NOARP> mtu 1500 ...
link/tunnel6 fd00::2 peer fd00::1
After the patch:
# ip li add vti6 type vti6 local fd00::2 remote fd00::1
# ip li show vti6
vti6@NONE: <POINTOPOINT,NOARP> mtu 8832 ...
link/tunnel6 fd00::2 peer fd00::1
Reported-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We support asynchronous crypto on layer 2 ESP now.
So no need to force synchronous crypto fallback on
offloading anymore.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch implements asynchronous crypto callbacks
and a backlog handler that can be used when IPsec
is done at layer 2 in the TX path. It also extends
the skb validate functions so that we can update
the driver transmit return codes based on async
crypto operation or to indicate that we queued the
packet in a backlog queue.
Joint work with: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We change the ESP GSO handlers to only segment the packets.
The ESP handling and encryption is defered to validate_xmit_xfrm()
where this is done for non GRO packets too. This makes the code
more robust and prepares for asynchronous crypto handling.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an old bugbear of mine:
https://www.mail-archive.com/netdev@vger.kernel.org/msg03894.html
By crafting special packets, it is possible to cause recursion
in our kernel when processing transport-mode packets at levels
that are only limited by packet size.
The easiest one is with DNAT, but an even worse one is where
UDP encapsulation is used in which case you just have to insert
an UDP encapsulation header in between each level of recursion.
This patch avoids this problem by reinjecting tranport-mode packets
through a tasklet.
Fixes: b05e106698 ("[IPV4/6]: Netfilter IPsec input hooks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
pskb_may_pull() can change skb->data, so we need to re-load pkt_md
and ershdr at the right place.
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If pskb_may_pull return failed, return PACKET_REJECT
instead of -ENOMEM.
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.
A Multicast Router will listen on address ff02::16 for MLDv2 messages.
Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.
This results in the packet being looped back but discarded before being
delivered to the Multicast Router.
This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to support for ipv4 erspan, this patch adds
erspan v2 to ip6erspan tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch refactors the existing erspan implementation in order
to support erspan version 2, which has additional metadata. So, in
stead of having one 'struct erspanhdr' holding erspan version 1,
breaks it into 'struct erspan_base_hdr' and 'struct erspan_metadata'.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The follow patchset contains Netfilter fixes for your net tree,
they are:
1) Fix compilation warning in x_tables with clang due to useless
redundant reassignment, from Colin Ian King.
2) Add bugtrap to net_exit to catch uninitialized lists, patch
from Vasily Averin.
3) Fix out of bounds memory reads in H323 conntrack helper, this
comes with an initial patch to remove replace the obscure
CHECK_BOUND macro as a dependency. From Eric Sesterhenn.
4) Reduce retransmission timeout when window is 0 in TCP conntrack,
from Florian Westphal.
6) ctnetlink clamp timeout to INT_MAX if timeout is too large,
otherwise timeout wraps around and it results in killing the
entry that is being added immediately.
7) Missing CAP_NET_ADMIN checks in cthelper and xt_osf, due to
no netns support. From Kevin Cernekee.
8) Missing maximum number of instructions checks in xt_bpf, patch
from Jann Horn.
9) With no CONFIG_PROC_FS ipt_CLUSTERIP compilation breaks,
patch from Arnd Bergmann.
10) Missing netlink attribute policy in nftables exthdr, from
Florian Westphal.
11) Enable conntrack with IPv6 MASQUERADE rules, as a357b3f80b
should have done in first place, from Konstantin Khlebnikov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller reported crashes in IPv6 stack [1]
Xin Long found that lo MTU was set to silly values.
IPv6 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in mld code where it is assumed
the mtu is suitable.
Fix this by reading device mtu once and checking IPv6 minimal MTU.
[1]
skbuff: skb_over_panic: text:0000000010b86b8d len:196 put:20
head:000000003b477e60 data:000000000e85441e tail:0xd4 end:0xc0 dev:lo
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.15.0-rc2-mm1+ #39
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x15c/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801db307508 EFLAGS: 00010286
RAX: 0000000000000082 RBX: ffff8801c517e840 RCX: 0000000000000000
RDX: 0000000000000082 RSI: 1ffff1003b660e61 RDI: ffffed003b660e95
RBP: ffff8801db307570 R08: 1ffff1003b660e23 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff85bd4020
R13: ffffffff84754ed2 R14: 0000000000000014 R15: ffff8801c4e26540
FS: 0000000000000000(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000463610 CR3: 00000001c6698000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
skb_over_panic net/core/skbuff.c:109 [inline]
skb_put+0x181/0x1c0 net/core/skbuff.c:1694
add_grhead.isra.24+0x42/0x3b0 net/ipv6/mcast.c:1695
add_grec+0xa55/0x1060 net/ipv6/mcast.c:1817
mld_send_cr net/ipv6/mcast.c:1903 [inline]
mld_ifc_timer_expire+0x4d2/0x770 net/ipv6/mcast.c:2448
call_timer_fn+0x23b/0x840 kernel/time/timer.c:1320
expire_timers kernel/time/timer.c:1357 [inline]
__run_timers+0x7e1/0xb60 kernel/time/timer.c:1660
run_timer_softirq+0x4c/0xb0 kernel/time/timer.c:1686
__do_softirq+0x29d/0xbb2 kernel/softirq.c:285
invoke_softirq kernel/softirq.c:365 [inline]
irq_exit+0x1d3/0x210 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:540 [inline]
smp_apic_timer_interrupt+0x16b/0x700 arch/x86/kernel/apic/apic.c:1052
apic_timer_interrupt+0xa9/0xb0 arch/x86/entry/entry_64.S:920
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MD5-key that belongs to a connection is identified by the peer's
IP-address. When we are in tcp_v4(6)_reqsk_send_ack(), we are replying
to an incoming segment from tcp_check_req() that failed the seq-number
checks.
Thus, to find the correct key, we need to use the skb's saddr and not
the daddr.
This bug seems to have been there since quite a while, but probably got
unnoticed because the consequences are not catastrophic. We will call
tcp_v4_reqsk_send_ack only to send a challenge-ACK back to the peer,
thus the connection doesn't really fail.
Fixes: 9501f97229 ("tcp md5sig: Let the caller pass appropriate key for tcp_v{4,6}_do_calc_md5_hash().")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4d3a57f23d ("netfilter: conntrack: do not enable connection
tracking unless needed") conntrack is disabled by default unless some
module explicitly declares dependency in particular network namespace.
Fixes: a357b3f80b ("netfilter: nat: add dependencies on conntrack module")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
introduced new exit point in ipxip6_rcv. however rcu_read_unlock is
missing there. this diff is fixing this
v1->v2:
instead of doing rcu_read_unlock in place, we are going to "drop"
section (to prevent skb leakage)
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ip6 gretap and ip4 gretap, the patch allows
erspan tunnel to operate in collect metadata mode.
bpf_skb_[gs]et_tunnel_key() helpers can make use of
it right away.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern