This probably doesn't cause an issue, since the code checks the view
type dependent size of the views before comparing them, but let's follow
the practice to bzero the whole struct when initializing it.
v2: Use {} instead of { } struct intializer. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325214808.2071517-6-imre.deak@intel.com
This probably doesn't cause an issue, since the code checks the view
type dependent size of the views before comparing them, but let's follow
the practice to bzero the whole struct when initializing it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325214808.2071517-5-imre.deak@intel.com
The HW plane state is cleared and inited after we store the rotation to
it, so store it instead to the uapi state to match what we do with all
other plane state until intel_plane_copy_uapi_to_hw_state() is called.
Rotation for initial FBs is not supported atm, but let's still fix the
plane state setup here.
While at it remove the redundant intel_state->uapi.src/dst init, which
will be done in intel_plane_copy_uapi_to_hw_state().
v2: Remove redundant intel_state->uapi.src/dst init. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325214808.2071517-2-imre.deak@intel.com
struct drm_i915_private, struct intel_crtc_state and
struct intel_crtc is declared twice.
Remove the duplicate.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210326012527.875026-1-wanjiabing@vivo.com
The dbuf bandwidth calculations don't need the planes to be
added to the state. Each plane's data rate has already been
precalculated and stored in the crtc state, and that with
the dbuf slice usage for each plane is all the dbuf bandwidth
code needs to figure out what the minimum cdclk is.
What we're trying to do here is make sure each plane recalculates
its minimum cdclk (ie. plane->min_cdclk()) on those platforms where
the number of active planes affects the result of said calculation.
Nothing to do with any dbuf cdclk requirements.
Not sure if we had stuff in slightly different order or what,
but at least in the current scheme this is not necessary.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325004415.17432-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
This changes the way revids not present in the array are handled:
- For gaps in the array, the next present revid is used.
- For revids beyond the array, the new STEP_FUTURE is used instead of
the last revid in the array.
In both cases, we'll get debug logging of what's going on.
v2: Rename stepping->step
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/756fe3d75b1e91ef812fc1fd3f70337e9c571d91.1616764798.git.jani.nikula@intel.com
Add new symbolic names for revision ids, and convert KBL revids to use
them via the new stepping check macros.
This also fixes theoretical out of bounds access to kbl_revids array.
v3: upgrade dbg to warn on unknown revid (José)
v2: Rename stepping->step
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/79b6c48211c6b214165391d350d556bad748f747.1616764798.git.jani.nikula@intel.com
Add new runtime info field for stepping. Add new helpers for accessing
them. As we'll be switching platforms over to the new scheme
incrementally, check for non-initialized steppings.
In case a platform does not have separate display and gt steppings, it's
okay to use a common shorthand. However, in this case the display
stepping must not be initialized, and gt stepping is the single point of
truth.
v3: Remove IS_STEP() (José)
v2: Rename stepping->step
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bb4275733fa390ea3dbf6f62794d55b616665230.1616764798.git.jani.nikula@intel.com
Accidentally transposed the arguments to skl_plane_wm_level()
which is causing us to mistakenly think that the plane watermarks
have/have not changed when the opposite may be true. Swap the
arguments so this actually works.
The other uses of this look OK.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 2871b2fde4 ("drm/i915: Fix TGL+ plane SAGV watermark programming")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210325004415.17432-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Update logic to program AUD_FREQ_CNTRL register based on new guidance.
Earlier this register was configured by BIOS and driver discovered the
value at init. This is no longer recommended and instead driver should
set the values based on the hardware revision.
Add the recommended values for all supported hardware. This change applies
for all GEN12+ hardware. For TGL, some special case handling is needed
to not break existing systems.
Extend the debug print to also include values of the register as written
by BIOS. This can help debug rare cases where BIOS has configured the link
settings to incorrect values.
Bspec: 49279
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210324123725.4170214-1-kai.vehmanen@linux.intel.com
To optimize some task deferring it until runtime resume unless someone
holds a runtime PM reference (because in this case the task can be done
w/o the overhead of runtime resume), we have to use the runtime PM
get-if-active logic: If the runtime PM usage count is 0 (and so
get-if-in-use would return false) the runtime suspend handler is not
necessarily called yet (it could be just pending), so the device is not
necessarily powered down, and so the runtime resume handler is not
guaranteed to be called.
The fence revocation depends on the above deferral, so add a
get-if-active helper and use it during fence revocation.
v2:
- Add code comment explaining the fence reg programming deferral logic
to i915_vma_revoke_fence(). (Chris)
- Add Cc: stable and Fixes: tags. (Chris)
- Fix the function docbook comment.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 181df2d458 ("drm/i915: Take rpm wakelock for releasing the fence on unbind")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210322204223.919936-1-imre.deak@intel.com
Convert the display-specific usage of INTEL_GEN, while leaving the
non-display usage as-is for now.
In the near-future we'll probably want to think about moving display
interrupt handling to its own file under the display/ directory.
v2:
- Use new IS_DISPLAY_VER() macro.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-6-matthew.d.roper@intel.com
Although most of the code in this file is display-related (watermarks),
there's some functions that are not (e.g., clock gating). Thus we need
to do the conversions to DISPLAY_VER() manually here rather than using
Coccinelle.
In the near-future we'll probably want to think about moving watermark
logic out of intel_pm.c and into watermark-specific files under the
display/ directory.
v2:
- Use new IS_DISPLAY_VER macro where appropriate.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-5-matthew.d.roper@intel.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Although we've long referred to platforms by a single "GEN" number, the
hardware teams have recommended that we stop doing this since the
various component IP blocks are going to start using independent number
schemes with varying cadence. To support this, hardware platforms a bit
down the road are going to start providing MMIO registers that the
driver can read to obtain the "graphics version," "media version," and
"display version" without needing to do a PCI ID -> platform -> version
translation.
Although our current platforms don't yet expose these registers (and the
next couple we release probably won't have them yet either), the
hardware teams would still like to see us move to this independent
numbering scheme now in preparation. For i915 that means we should try
to eliminate all usage of INTEL_GEN() throughout our code and instead
replace it with separate GRAPHICS_VER(), MEDIA_VER(), and DISPLAY_VER()
constructs in the code. For old platforms, these will all usually give
the same value for each IP block (aside from a few special cases like
GLK which we can no more accurately represent as graphics=9 +
display=10), but future platforms will have more flexibility to bump IP
version numbers independently.
The upcoming ADL-P platform will have a display version of 13 and a
graphics version of 12, so let's just the first step of breaking out
DISPLAY_VER(), but leaving the rest of INTEL_GEN() untouched for now.
For now we'll automatically derive the display version from the
platform's INTEL_GEN() value except in cases where an alternative
display version is explicitly provided in the device info structure.
We also add some helper macros IS_DISPLAY_VER(i915, ver) and
IS_DISPLAY_RANGE(i915, from, until) that match the behavior of the
existing gen-based macros. However unlike IS_GEN(), we will implement
those macros with direct comparisons rather than trying to maintain a
mask to help compiler optimization. In practice the optimization winds
up not being used in very many places (since the vast majority of our
platform checks are of the form "gen >= x") so there is pretty minimal
size reduction in the final driver binary[1]. We're also likely going
to need to extend these version numbers to non-integer major.minor
values at some point in the future, so the mask approach won't work at
all once we get to platforms like that.
[1] The results before/after the next patch in this series, which
switches our code over to the new display macros:
$ size i915.ko.{orig,new}
text data bss dec hex filename
2940291 102944 5384 3048619 2e84ab i915.ko.orig
2940723 102956 5384 3049063 2e8667 i915.ko.new
v2:
- Move version into device info's display sub-struct. (Jani)
- Add extra parentheses to macros. (Jani)
- Note the lack of genmask optimization in the display-based macros and
give size data. (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-3-matthew.d.roper@intel.com
ILK is the only platform that we consider "gen5" and SNB is the only
platform we consider "gen6." Add an IS_SANDYBRIDGE() macro and then
replace numeric platform tests for these two generations with direct
platform tests with the following Coccinelle semantic patch:
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 5)
+ IS_IRONLAKE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 6)
+ IS_SANDYBRIDGE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN_RANGE(dev_priv, 5, 6)
+ IS_IRONLAKE(dev_priv) || IS_SANDYBRIDGE(dev_priv)
This will simplify our upcoming patches which eliminate INTEL_GEN()
usage in the display code.
v2:
- Reverse ilk/snb order for IS_GEN_RANGE conversion. (Ville)
- Rebase + regenerate from semantic patch
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-2-matthew.d.roper@intel.com
Use the correct DSS CTL registers for ICL DSI transcoders.
As a side effect, this also brings back the sanity check for trying to
use pipe DSC registers on pipe A on ICL.
Fixes: 8a029c113b ("drm/i915/dp: Modify VDSC helpers to configure DSC for Bigjoiner slave")
References: http://lore.kernel.org/r/87eegxq2lq.fsf@intel.com
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: <stable@vger.kernel.org> # v5.11+
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319115333.8330-1-jani.nikula@intel.com
The enabled_planes bitmask was supposed to track logically enabled
planes (ie. fb!=NULL and crtc!=NULL), but instead we end up putting
even disabled planes into the bitmask since
intel_plane_atomic_check_with_state() only takes the early exit
if the plane was disabled and stays disabled. I think I misread
the early said codepath to exit whenever the plane is logically
disabled, which is not true.
So let's fix this up properly and set the bit only when the plane
actually is logically enabled.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Fixes: ee42ec19ca ("drm/i915: Track logically enabled planes for hw state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305153610.12177-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
hdcp2_enable_stream_encryption shouldn't get called in case
of any port authentication or encryption error, though
hdcp2_enable_stream_encryption checks for link encryption
before enabling stream encryption and returns error but
this return error code won't be correct in case of any error
due to port authentication and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-4-anshuman.gupta@intel.com
When stream encryption enabling fails due to Link encryption status
has stopped, prepare HDCP2 for recovery by disabling port authentication
and encryption such that it can re-attempt port authentication
and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-3-anshuman.gupta@intel.com
DP MST Link Check performed only for the connector involved with
HDCP port authentication and encryption, for other connector it
simply returns link check with true and update the uevent.
Therefore in case of HDCP 2.2 link failure, disable HDCP encryption
and de-authenticate the port so next time it can enable port
authentication and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-2-anshuman.gupta@intel.com
It requires to check streams type1 capability in mst topology
by checking Rxinfo instead connector HDCP2.x capability in
order to enforce type0 stream encryption in a mix of
HDCP {1.x,2.x} mst topology.
Rxcaps always shows HDCP 2.x capability of immediate downstream
connector. Let's use Rxinfo HDCP1_DEVICE_DOWNSTREAM bit to
detect a HDCP {1.x,2.x} mix mst topology.
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319091732.17547-1-anshuman.gupta@intel.com
Extract the g4x+ HDMI low level code to its own file,
leaving intel_hdmi.c to deal with higher level issues.
The infoframe support I decided to leave in intel_hdmi.c
since I think we need to move that as a whole to its own file.
It is after all used also for DP SDPs, so no longer HDMI
specific.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161015.22070-7-ville.syrjala@linux.intel.com
Move the g4x+ DP code into a new file. This will leave mostly
platform agnostic code in intel_dp.c. Well, the misplaced phy
test stuff pretty much ruins that, but let's squint real hard
for now.
v2: Add comment exlaining which platforms are covered (Daniel)
Leave intel_dp_unused_lane_mask() be since it is pretty generic
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161015.22070-6-ville.syrjala@linux.intel.com
By the specification the 0xF0000 - 0xF02FF range is only valid if the
LTTPR revision at 0xF0000 is at least 1.4. Disable the LTTPR support
otherwise.
Fixes: 7b2a4ab8b0 ("drm/i915: Switch to LTTPR transparent mode link training")
Cc: <stable@vger.kernel.org> # v5.11
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210317184901.4029798-4-imre.deak@intel.com
By the specification the 0xF0000-0xF02FF range is only valid when the
DPCD revision is 1.4 or higher. Disable LTTPR support if this isn't so.
Trying to detect LTTPRs returned corrupted values for the above DPCD
range at least on a Skylake host with an LG 43UD79-B monitor with a DPCD
revision 1.2 connected.
v2: Add the actual version check.
v3: Fix s/DRPX/DPRX/ typo.
Fixes: 7b2a4ab8b0 ("drm/i915: Switch to LTTPR transparent mode link training")
Cc: <stable@vger.kernel.org> # v5.11
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210317190149.4032966-1-imre.deak@intel.com
The spec requires to use at least 3.2ms for the AUX timeout period if
there are LT-tunable PHY Repeaters on the link (2.11.2). An upcoming
spec update makes this more specific, by requiring a 3.2ms minimum
timeout period for the LTTPR detection reading the 0xF0000-0xF0007
range (3.6.5.1).
Accordingly disable LTTPR detection until GLK, where the maximum timeout
we can set is only 1.6ms.
Link training in the non-transparent mode is known to fail at least on
some SKL systems with a WD19 dock on the link, which exposes an LTTPR
(see the References below). While this could have different reasons
besides the too short AUX timeout used, not detecting LTTPRs (and so not
using the non-transparent LT mode) fixes link training on these systems.
While at it add a code comment about the platform specific maximum
timeout values.
v2: Add a comment about the g4x maximum timeout as well. (Ville)
Reported-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Santiago Zarate <santiago.zarate@suse.com>
Reported-and-tested-by: Bodo Graumann <mail@bodograumann.de>
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3166
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: <stable@vger.kernel.org> # v5.11
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210317184901.4029798-2-imre.deak@intel.com
Remove code for resetting frl related members from intel_disable_dp, as
this is not applicable for older platforms.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210309043915.1921-3-ankit.k.nautiyal@intel.com
Add intel_bios_encoder_data pointer to encoder, and use it for hdmi and
dp iboost. For starters, we only set the encoder->devdata for DDI
encoders, i.e. we can only use it for data that is used by DDI encoders.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bc49244ce68e136e5b21db4c4e6554bec9ac0fb.1615998927.git.jani.nikula@intel.com
Stop caching the information in ddi_port_info. We're phasing out
ddi_port_info usage completely, and prefer using the VBT child device
information directly using the provided helpers.
v2:
- Remove supports_typec_usb & supports_tbt from ddi_vbt_port_info (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b04bd183e7554aeb4bc3962af90d63171aa32fc2.1615998927.git.jani.nikula@intel.com
Start using struct intel_bios_encoder_data directly. We'll start
sanitizing the child device data directly as well, instead of the cached
data in ddi_port_info[]. The one downside here is having to store a
non-const pointer back to intel_bios_encoder_data.
Eventually we'll be able to have a direct pointer from encoder to
intel_bios_encoder_data, removing the need to go through the
ddi_port_info[] array altogether. And we'll be able to remove all the
cached data in ddi_port_info[].
v2:
- Remove supports_dp and supports_edp from ddi_port_info too
- Add devdata != NULL check in intel_bios_is_port_edp()
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> # v1
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/061df32a012ff640060920fcd730fb23f8717ee8.1615998927.git.jani.nikula@intel.com
These will be exposed to the rest of the driver and replace other
functions. Everything will operate on the child devices.
v2:
- Rebased, removed stray blank line
- Also abstracted intel_bios_encoder_supports_crt (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2bd40ccc093796d16300742d1789d78ffac3c450.1615998927.git.jani.nikula@intel.com
Instead of initialing data directly in ddi_port_info array, create fake
child devices for default outputs when the VBT is missing. This makes
further unification of output handling easier.
This will make intel_bios_is_port_present() return true for the fake
child devices. This may cause subtle changes in a handful of places.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/91675b40a78bd04bf138598d979661257181880d.1615998927.git.jani.nikula@intel.com
There are two main cases where the default outputs are useful when the
VBT is missing:
- There are some DDI-platform Chromebooks out there that do not have a
VBT, which worked by coincidence because of the default outputs. The
machines need to continue to work.
- Early platform enabling when the VBT might not be available. (This
could be circumvented by using the i915.vbt_firmware parameter.)
Prepare for generating fake child devices for the default outputs by
limiting the number of outputs. We don't want to generate excessive
amounts of fake child devices. This could be perhaps be limited even
more in the future, but match what's possible on all DDI platforms.
Note that limiting the defaults to non-TypeC ports in commit
828ccb31cf ("drm/i915/icl: Add TypeC ports only if VBT is present") is
a more strict limit, and makes this a no-op on recent platforms.
v2: Rewrote commit message
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5c9c9743af1c7265a2c976d582b7a6685ec0c414.1615998927.git.jani.nikula@intel.com
Imre Deak