The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.
In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".
However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the SD host controller tries to probe again due to the derferred
probe mechanism, it will always keep the SD host device as runtime
resume state due to missing the runtime put operation in error path
last time.
Thus add the pm_runtime_put_noidle() in error path to make the PM runtime
counter balance, which can make the SD host device's PM runtime work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Spreadtrum SD card voltage switching, besides regulator setting,
it also need switch related pin's state to output corresponding voltage.
This patch adds pin control operation to support voltage switch.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Spreadtrum SD host controller, we can not use standard SD registers
to change and detect the I/O voltage signals, since our voltage regulator
for I/O is fixed in hardware, and no signals were connected to the SD
controller. Thus add Spreadtrum specific voltage switch ops to change
voltage instead of using standard SD host registers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the PHY DLL delay for each timing mode, which is used to sample the clock
accurately and make the clock more stable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SD host controller, when we changed the clock to be
more than 52M, we should enable the PHY DLL which is used to track the
clock frequency to make the clock work more stable. Otherwise deviation
may occur of the higher clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the get_max_timeout_count() interface to set the Spredtrum SD
host controller actual maximum timeout count.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SC9860 platform, we should enable another gate clock
'2x_enable' to make the SD host controller work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Missed to check the enable clock's return value, fix it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang