Commit Graph

857 Commits

Author SHA1 Message Date
nikolay@redhat.com 25e40305d4 bonding: mc addresses don't get deleted on enslave failure
Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.

v2: update log message and don't move code unnecessarily

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 17:48:18 -04:00
Andy Gospodarek bb5b052f75 bond: add support to read speed and duplex via ethtool
This patch adds support for the get_settings ethtool op to the bonding
driver.  This was motivated by users who wanted to get the speed of the
bond and compare that against throughput to understand utilization.
The behavior before this patch was added was problematic when computing
line utilization after trying to get link-speed and throughput via SNMP.

Output from ethtool looks like this for a round-robin bond:

Settings for bond0:
	Supported ports: [ ]
	Supported link modes:   Not reported
	Supported pause frame use: No
	Supports auto-negotiation: No
	Advertised link modes:  Not reported
	Advertised pause frame use: No
	Advertised auto-negotiation: No
	Speed: 11000Mb/s
	Duplex: Full
	Port: Other
	PHYAD: 0
	Transceiver: internal
	Auto-negotiation: off
	MDI-X: Unknown
	Link detected: yes

I tested this and verified it works as expected.  A test was also done
on a version backported to an older kernel and it worked well there.

v2: Switch to using ethtool_cmd_speed_set to set speed, added check to
SLAVE_IS_OK for each slave in bond, dropped mode-specific calculations
as they were not needed, and set port type to 'Other.'

v3: Fix useless assignment and checkpatch warning.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 16:39:50 -04:00
Patrick McHardy 86a9bad3ab net: vlan: add protocol argument to packet tagging functions
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:46:06 -04:00
Patrick McHardy 1fd9b1fc31 net: vlan: prepare for 802.1ad support
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:27 -04:00
Patrick McHardy 80d5c3689b net: vlan: prepare for 802.1ad VLAN filtering offload
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:27 -04:00
Patrick McHardy f646968f8f net: vlan: rename NETIF_F_HW_VLAN_* feature flags to NETIF_F_HW_VLAN_CTAG_*
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-19 14:45:26 -04:00
Eric Dumazet 4394542ca4 bonding: fix l23 and l34 load balancing in forwarding path
Since commit 6b923cb718 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.

Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.

More generally, the transport header might not be in the skb head.

Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.

Reported-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-18 15:07:29 -04:00
nikolay@redhat.com b6a5a7b9a5 bonding: IFF_BONDING is not stripped on enslave failure
While enslaving a new device and after IFF_BONDING flag is set, in case
of failure it is not stripped from the device's priv_flags while
cleaning up, which could lead to other problems.
Cleaning at err_close because the flag is set after dev_open().

v2: no change

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-11 16:01:47 -04:00
nikolay@redhat.com 6101391d4a bonding: fix netdev event NULL pointer dereference
In commit 471cb5a33d ("bonding: remove
usage of dev->master") a bug was introduced which causes a NULL pointer
dereference. If a bond device is in mode 6 (ALB) and a slave is added
it will dereference a NULL pointer in bond_slave_netdev_event().
This is because in bond_enslave we have bond_alb_init_slave() which
changes the MAC address of the slave and causes a NETDEV_CHANGEADDR.
Then we have in bond_slave_netdev_event():
        struct slave *slave = bond_slave_get_rtnl(slave_dev);
        struct bonding *bond = slave->bond;
bond_slave_get_rtnl() dereferences slave_dev->rx_handler_data which at
that time is NULL since netdev_rx_handler_register() is called later.

This is fixed by checking if slave is NULL before dereferencing it.

v2: Comment style changed.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-11 16:01:47 -04:00
Al Viro d9dda78bad procfs: new helper - PDE_DATA(inode)
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data.  Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2013-04-09 14:13:32 -04:00
nikolay@redhat.com 69b0216ac2 bonding: fix bonding_masters race condition in bond unloading
While the bonding module is unloading, it is considered that after
rtnl_link_unregister all bond devices are destroyed but since no
synchronization mechanism exists, a new bond device can be created
via bonding_masters before unregister_pernet_subsys which would
lead to multiple problems (e.g. NULL pointer dereference, wrong RIP,
list corruption).

This patch fixes the issue by removing any bond devices left in the
netns after bonding_masters is removed from sysfs.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08 16:45:09 -04:00
nikolay@redhat.com ffcdedb667 Revert "bonding: remove sysfs before removing devices"
This reverts commit 4de79c737b.

This patch introduces a new bug which causes access to freed memory.
In bond_uninit: list_del(&bond->bond_list);
bond_list is linked in bond_net's dev_list which is freed by
unregister_pernet_subsys.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08 16:45:09 -04:00
David S. Miller d978a6361a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/nfc/microread/mei.c
	net/netfilter/nfnetlink_queue_core.c

Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07 18:37:01 -04:00
Veaceslav Falico 4de79c737b bonding: remove sysfs before removing devices
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.

Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-05 00:46:13 -04:00
David S. Miller d662483264 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull net into net-next to get the synchronize_net() bug fix in
bonding.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-03 01:31:54 -04:00
Veaceslav Falico fcd99434fb bonding: get netdev_rx_handler_unregister out of locks
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-02 12:05:28 -04:00
David S. Miller a210576cf8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	net/mac80211/sta_info.c
	net/wireless/core.h

Two minor conflicts in wireless.  Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-01 13:36:50 -04:00
nikolay@redhat.com 1bc7db1678 bonding: fix disabling of arp_interval and miimon
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-29 15:02:49 -04:00
David S. Miller e2a553dbf1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	include/net/ipip.h

The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-27 13:52:49 -04:00
Veaceslav Falico 9fe16b78ee bonding: remove already created master sysfs link on failure
If slave sysfs symlink failes to be created - we end up without removing
the master sysfs symlink. Remove it in case of failure.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-26 13:00:02 -04:00
Veaceslav Falico ad999eee66 bonding: cleanup unneeded rcu_read_lock()
bond_resend_igmp_join_requests_delayed() calls _resend_igmp_join_requests()
under rcu_read_lock(), while it gets its own rcu_read_lock() for the whole
function. Remove the lock from the _delayed function.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-26 12:49:40 -04:00
Veaceslav Falico 876254ae27 bonding: don't call update_speed_duplex() under spinlocks
bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsibility to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.

I've tested it on all combinations of ifup/ifdown, autoneg/speed/duplex
changes, remote-controlled and local, on (not) MII-based cards. All changes
are visible.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-13 04:53:17 -04:00
Veaceslav Falico 80028ea1c0 bonding: fire NETDEV_RELEASE event only on 0 slaves
Currently, if we set up netconsole over bonding and release a slave,
netconsole will stop logging on the whole bonding device. Change the
behavior to stop the netconsole only when the last slave is released.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-07 16:15:18 -05:00
Jiri Pirko 6c8c4e4c24 bond: check if slave count is 0 in case when deciding to take slave's mac
in bond_enslave(), check slave_cnt before actually using slave address.

introduced by:
commit 409cc1f8a4 (bond: have random dev address by default instead of zeroes)

Reported-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-26 17:30:38 -05:00
Doug Goldstein b3f92b63c4 bonding: set sysfs device_type to 'bond'
Sets the sysfs device_type to 'bond' for udev. This allows udev rules to
be created for bond devices. This is similar to how other network
devices set their device_type.

Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-19 00:51:09 -05:00
nikolay@redhat.com 0896341a44 bonding: fix bond_release_all inconsistencies
This patch fixes the following inconsistencies in bond_release_all:
- IFF_BONDING flag is not stripped from slaves
- MTU is not restored
- no netdev notifiers are sent
Instead of trying to keep bond_release and bond_release_all in sync
I think we can re-use bond_release as the environment for calling it
is correct (RTNL is held). I have been running tests for the past
week and they came out successful. The only way for bond_release to fail
is for the slave to be attached in a different bond or to not be a slave
but that cannot happen as RTNL is held and no slave manipulations can be
achieved.

V2: As suggested bond_release is renamed to __bond_release_one with a
new parameter "all" introduced so to avoid calling unnecessary code while
destroying a bond, and a wrapper for it called bond_release is created
because of ndo_del_link. bond_release_all() is removed.

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-19 00:51:09 -05:00
nikolay@redhat.com e0809dbc47 bonding: Fix initialize after use for 3ad machine state spinlock
The 3ad machine state spinlock can be used before it is inititialized
while doing bond_enslave() (and the port is being initialized) since
port->slave is set before the lock is prepared, thus causing soft
lock-ups and a multitude of other nasty bugs.

[ Rename __initialize_port_locks() variable name to 'slave' -DaveM ]

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-19 00:51:08 -05:00
nikolay@redhat.com b59340c2c0 bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
port->slave can be NULL since it's being initialized in bond_enslave
thus dereferencing a NULL pointer in bond_3ad_update_lacp_rate()
Also fix a minor bug, which could cause a port not to have
AD_STATE_LACP_TIMEOUT since there's no sync between
bond_3ad_update_lacp_rate() and bond_3ad_bind_slave(), by changing
the read_lock to a write_lock_bh in bond_3ad_update_lacp_rate().

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-19 00:51:08 -05:00
Neil Horman 2cde6acd49 netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock
__netpoll_rcu_free is used to free netpoll structures when the rtnl_lock is
already held.  The mechanism is used to asynchronously call __netpoll_cleanup
outside of the holding of the rtnl_lock, so as to avoid deadlock.
Unfortunately, __netpoll_cleanup modifies pointers (dev->np), which means the
rtnl_lock must be held while calling it.  Further, it cannot be held, because
rcu callbacks may be issued in softirq contexts, which cannot sleep.

Fix this by converting the rcu callback to a work queue that is guaranteed to
get scheduled in process context, so that we can hold the rtnl properly while
calling __netpoll_cleanup

Tested successfully by myself.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Cong Wang <amwang@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-11 19:19:33 -05:00
David S. Miller 188d1f76d0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/intel/e1000e/ethtool.c
	drivers/net/vmxnet3/vmxnet3_drv.c
	drivers/net/wireless/iwlwifi/dvm/tx.c
	net/ipv6/route.c

The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.

The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.

The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.

The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-05 14:12:20 -05:00
Gao feng 387ff91184 netns: bond: allow unprivileged users to control bond device
reduce the permission check of bond device's ioctl.
allow the userns root to control the bond device.

Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-04 13:12:16 -05:00
Jiri Pirko 409cc1f8a4 bond: have random dev address by default instead of zeroes
Makes more sense to have randomly generated address by default than to
have all zeroes. It also allows user to for example put the bond into
bridge without need to have any slaves in it.

Also note that this changes only behaviour of bonds with no slaves. Once
the first slave device is enslaved, its address will be used (no change
here).

Also, fix dev_assign_type values on the way.

Reported-by: Pavel Šimerda <psimerda@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-30 15:34:00 -05:00
Milos Vyletel eb492f7443 bonding: unset primary slave via sysfs
When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.

 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

 echo "" > /sys/class/net/bond0/bonding/primary
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None

 sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
 ifdown bond0 && ifup bond0

without patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

with patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None

Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-29 15:43:35 -05:00
Jiri Pirko 7826d43f2d ethtool: fix drvinfo strings set in drivers
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-06 21:06:31 -08:00
Jiri Pirko 471cb5a33d bonding: remove usage of dev->master
Benefit from new upper dev list and free bonding from dev->master usage.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-04 13:31:50 -08:00
Konstantin Khlebnikov cfb6f99dd9 bonding: do not cancel works in bond_uninit()
Bonding initializes these works in bond_open() and cancels in bond_close(),
thus in bond_uninit() they are already canceled but may be unitialized yet.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-14 13:14:07 -05:00
Linus Torvalds a2013a13e6 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
 "Usual stuff -- comment/printk typo fixes, documentation updates, dead
  code elimination."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  HOWTO: fix double words typo
  x86 mtrr: fix comment typo in mtrr_bp_init
  propagate name change to comments in kernel source
  doc: Update the name of profiling based on sysfs
  treewide: Fix typos in various drivers
  treewide: Fix typos in various Kconfig
  wireless: mwifiex: Fix typo in wireless/mwifiex driver
  messages: i2o: Fix typo in messages/i2o
  scripts/kernel-doc: check that non-void fcts describe their return value
  Kernel-doc: Convention: Use a "Return" section to describe return values
  radeon: Fix typo and copy/paste error in comments
  doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
  various: Fix spelling of "asynchronous" in comments.
  Fix misspellings of "whether" in comments.
  eisa: Fix spelling of "asynchronous".
  various: Fix spelling of "registered" in comments.
  doc: fix quite a few typos within Documentation
  target: iscsi: fix comment typos in target/iscsi drivers
  treewide: fix typo of "suport" in various comments and Kconfig
  treewide: fix typo of "suppport" in various comments
  ...
2012-12-13 12:00:02 -08:00
Linus Torvalds 6be35c700f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David Miller:

1) Allow to dump, monitor, and change the bridge multicast database
   using netlink.  From Cong Wang.

2) RFC 5961 TCP blind data injection attack mitigation, from Eric
   Dumazet.

3) Networking user namespace support from Eric W. Biederman.

4) tuntap/virtio-net multiqueue support by Jason Wang.

5) Support for checksum offload of encapsulated packets (basically,
   tunneled traffic can still be checksummed by HW).  From Joseph
   Gasparakis.

6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
   Daniel Borkmann.

7) Bridge port parameters over netlink and BPDU blocking support
   from Stephen Hemminger.

8) Improve data access patterns during inet socket demux by rearranging
   socket layout, from Eric Dumazet.

9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
   Jon Maloy.

10) Update TCP socket hash sizing to be more in line with current day
    realities.  The existing heurstics were choosen a decade ago.
    From Eric Dumazet.

11) Fix races, queue bloat, and excessive wakeups in ATM and
    associated drivers, from Krzysztof Mazur and David Woodhouse.

12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
    in VXLAN driver, from David Stevens.

13) Add "oops_only" mode to netconsole, from Amerigo Wang.

14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
    allow DCB netlink to work on namespaces other than the initial
    namespace.  From John Fastabend.

15) Support PTP in the Tigon3 driver, from Matt Carlson.

16) tun/vhost zero copy fixes and improvements, plus turn it on
    by default, from Michael S. Tsirkin.

17) Support per-association statistics in SCTP, from Michele
    Baldessari.

And many, many, driver updates, cleanups, and improvements.  Too
numerous to mention individually.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
  net/mlx4_en: Add support for destination MAC in steering rules
  net/mlx4_en: Use generic etherdevice.h functions.
  net: ethtool: Add destination MAC address to flow steering API
  bridge: add support of adding and deleting mdb entries
  bridge: notify mdb changes via netlink
  ndisc: Unexport ndisc_{build,send}_skb().
  uapi: add missing netconf.h to export list
  pkt_sched: avoid requeues if possible
  solos-pci: fix double-free of TX skb in DMA mode
  bnx2: Fix accidental reversions.
  bna: Driver Version Updated to 3.1.2.1
  bna: Firmware update
  bna: Add RX State
  bna: Rx Page Based Allocation
  bna: TX Intr Coalescing Fix
  bna: Tx and Rx Optimizations
  bna: Code Cleanup and Enhancements
  ath9k: check pdata variable before dereferencing it
  ath5k: RX timestamp is reported at end of frame
  ath9k_htc: RX timestamp is reported at end of frame
  ...
2012-12-12 18:07:07 -08:00
Ben Hutchings c772dde343 bonding: Fix check for ethtool get_link operation support
Since commit 2c60db0370 ('net: provide a default dev->ethtool_ops')
all devices have a non-null ethtool_ops.  Test only
dev->ethtool_ops->get_link in both places where we care.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-07 14:35:35 -05:00
Jiri Bohac e53665c6ea bonding: delete migrated IP addresses from the rlb hash table
Bonding in balance-alb mode records information from ARP packets
passing through the bond in a hash table (rx_hashtbl).

At certain situations (e.g. link change of a slave),
rlb_update_rx_clients() will send out ARP packets to update ARP
caches of other hosts on the network to achieve RX load
balancing.

The problem is that once an IP address is recorded in the hash
table, it stays there indefinitely. If this IP address is
migrated to a different host in the network, bonding still sends
out ARP packets that poison other systems' ARP caches with
invalid information.

This patch solves this by looking at all incoming ARP packets,
and checking if the source IP address is one of the source
addresses stored in the rx_hashtbl. If it is, but the MAC
addresses differ, the corresponding hash table entries are
removed. Thus, when an IP address is migrated, the first ARP
broadcast by its new owner will purge the offending entries of
rx_hashtbl.

The hash table is hashed by ip_dst. To be able to do the above
check efficiently (not walking the whole hash table), we need a
reverse mapping (by ip_src).

I added three new members in struct rlb_client_info:
   rx_hashtbl[x].src_first will point to the start of a list of
      entries for which hash(ip_src) == x.
   The list is linked with src_next and src_prev.

When an incoming ARP packet arrives at rlb_arp_recv()
rlb_purge_src_ip() can quickly walk only the entries on the
corresponding lists, i.e. the entries that are likely to contain
the offending IP address.

To avoid confusion, I renamed these existing fields of struct
rlb_client_info:
	next -> used_next
	prev -> used_prev
	rx_hashtbl_head -> rx_hashtbl_used_head

(The current linked list is _not_ a list of hash table
entries with colliding ip_dst. It's a list of entries that are
being used; its purpose is to avoid walking the whole hash table
when looking for used entries.)

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-30 12:07:27 -05:00
zheng.li 567b871e50 bonding: rlb mode of bond should not alter ARP originating via bridge
Do not modify or load balance ARP packets passing through balance-alb
mode (wherein the ARP did not originate locally, and arrived via a bridge).

Modifying pass-through ARP replies causes an incorrect MAC address
to be placed into the ARP packet, rendering peers unable to communicate
with the actual destination from which the ARP reply originated.

Load balancing pass-through ARP requests causes an entry to be
created for the peer in the rlb table, and bond_alb_monitor will
occasionally issue ARP updates to all peers in the table instrucing them
as to which MAC address they should communicate with; this occurs when
some event sets rx_ntt.  In the bridged case, however, the MAC address
used for the update would be the MAC of the slave, not the actual source
MAC of the originating destination.  This would render peers unable to
communicate with the destinations beyond the bridge.

Signed-off-by: Zheng Li <zheng.x.li@oracle.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-30 12:07:26 -05:00
nikolay@redhat.com e196c0e579 bonding: fix race condition in bonding_store_slaves_active
Race between bonding_store_slaves_active() and slave manipulation
 functions. The bond_for_each_slave use in bonding_store_slaves_active()
 is not protected by any synchronization mechanism.
 NULL pointer dereference is easy to reach.
 Fixed by acquiring the bond->lock for the slave walk.

 v2: Make description text < 75 columns

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-29 13:13:15 -05:00
nikolay@redhat.com 90fb6250c5 bonding: make arp_ip_target parameter checks consistent with sysfs
The module can be loaded with arp_ip_target="255.255.255.255" which makes
 it impossible to remove as the function in sysfs checks for that value,
 so we make the parameter checks consistent with sysfs.

 v2: Fix formatting
 v3: Make description text < 75 columns

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-29 13:13:15 -05:00
nikolay@redhat.com fbb0c41b81 bonding: fix miimon and arp_interval delayed work race conditions
First I would give three observations which will be used later.
Observation 1: if (delayed_work_pending(wq)) cancel_delayed_work(wq)
 This usage is wrong because the pending bit is cleared just before the
 work's fn is executed and if the function re-arms itself we might end up
 with the work still running. It's safe to call cancel_delayed_work_sync()
 even if the work is not queued at all.
Observation 2: Use of INIT_DELAYED_WORK()
 Work needs to be initialized only once prior to (de/en)queueing.
Observation 3: IFF_UP is set only after ndo_open is called

Related race conditions:
1. Race between bonding_store_miimon() and bonding_store_arp_interval()
 Because of Obs.1 we can end up having both works enqueued.
2. Multiple races with INIT_DELAYED_WORK()
 Since the works are not protected by anything between INIT_DELAYED_WORK()
 and calls to (en/de)queue it is possible for races between the following
 functions:
 (races are also possible between the calls to INIT_DELAYED_WORK()
  and workqueue code)
 bonding_store_miimon() - bonding_store_arp_interval(), bond_close(),
			  bond_open(), enqueued functions
 bonding_store_arp_interval() - bonding_store_miimon(), bond_close(),
				bond_open(), enqueued functions
3. By Obs.1 we need to change bond_cancel_all()

Bugs 1 and 2 are fixed by moving all work initializations in bond_open
which by Obs. 2 and Obs. 3 and the fact that we make sure that all works
are cancelled in bond_close(), is guaranteed not to have any work
enqueued.
Also RTNL lock is now acquired in bonding_store_miimon/arp_interval so
they can't race with bond_close and bond_open. The opposing work is
cancelled only if the IFF_UP flag is set and it is cancelled
unconditionally. The opposing work is already cancelled if the interface
is down so no need to cancel it again. This way we don't need new
synchronizations for the bonding workqueue. These bugs (and fixes) are
tied together and belong in the same patch.
Note: I have left 1 line intentionally over 80 characters (84) because I
      didn't like how it looks broken down. If you'd prefer it otherwise,
      then simply break it.

 v2: Make description text < 75 columns

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-29 13:13:15 -05:00
Michal Kubeček 4e591b93d5 bonding: in balance-rr mode, set curr_active_slave only if it is up
If all slaves of a balance-rr bond with ARP monitor are enslaved
with down link state, bond keeps down state even after slaves
go up.

This is caused by bond_enslave() setting curr_active_slave to
first slave not taking into account its link state. As
bond_loadbalance_arp_mon() uses curr_active_slave to identify
whether slave's down->up transition should update bond's link
state, bond stays down even if slaves are up (until first slave
goes from up to down at least once).

Before commit f31c7937 "bonding: start slaves with link down for
ARP monitor", this was masked by slaves always starting in UP
state with ARP monitor (and MII monitor not relying on
curr_active_slave being NULL if there is no slave up).

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-28 11:28:45 -05:00
Sarveshwar Bandi 0e376bd0b7 bonding: Bonding driver does not consider the gso_max_size/gso_max_segs setting of slave devices.
Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach.

Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-21 11:50:31 -05:00
Masanari Iida 02582e9bcc treewide: fix typo of "suport" in various comments and Kconfig
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-11-19 14:16:09 +01:00
nikolay@redhat.com c84e1590d1 bonding: fix second off-by-one error
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.

How to reproduce:
 with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
 modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
 echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>

Note: Sorry for the second patch but I missed this one while checking
      the file. You can squash them into one patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:53:44 -04:00
nikolay@redhat.com eb6e98a1b2 bonding: fix off-by-one error
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.

How to reproduce:
 with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
 modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
 echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-01 11:53:43 -04:00
Jiri Pirko 55462cf30a vlan: fix bond/team enslave of vlan challenged slave/port
In vlan_uses_dev() check for number of vlan devs rather than existence
of vlan_info. The reason is that vlan id 0 is there without appropriate
vlan dev on it by default which prevented from enslaving vlan challenged
dev.

Reported-by: Jon Stanley <jstanley@rmrf.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-16 14:41:46 -04:00
Eric Dumazet 49ee49202b bonding: set qdisc_tx_busylock to avoid LOCKDEP splat
If a qdisc is installed on a bonding device, its possible to get
following lockdep splat under stress :

 =============================================
 [ INFO: possible recursive locking detected ]
 3.6.0+ #211 Not tainted
 ---------------------------------------------
 ping/4876 is trying to acquire lock:
  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830

 but task is already holding lock:
  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock);
   lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 6 locks held by ping/4876:
  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff815e5030>] raw_sendmsg+0x600/0xc30
  #1:  (rcu_read_lock_bh){.+....}, at: [<ffffffff815ba4bd>] ip_finish_output+0x12d/0x870
  #2:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830
  #3:  (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830
  #4:  (&bond->lock){++.?..}, at: [<ffffffffa02128c1>] bond_start_xmit+0x31/0x4b0 [bonding]
  #5:  (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830

 stack backtrace:
 Pid: 4876, comm: ping Not tainted 3.6.0+ #211
 Call Trace:
  [<ffffffff810a0145>] __lock_acquire+0x715/0x1b80
  [<ffffffff810a256b>] ? mark_held_locks+0x9b/0x100
  [<ffffffff810a1bf2>] lock_acquire+0x92/0x1d0
  [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830
  [<ffffffff81726b7c>] _raw_spin_lock+0x3c/0x50
  [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830
  [<ffffffff8106264d>] ? rcu_read_lock_bh_held+0x5d/0x90
  [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830
  [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570
  [<ffffffffa0212a6a>] bond_start_xmit+0x1da/0x4b0 [bonding]
  [<ffffffff815796d0>] dev_hard_start_xmit+0x240/0x6b0
  [<ffffffff81597c6e>] sch_direct_xmit+0xfe/0x2a0
  [<ffffffff8157a249>] dev_queue_xmit+0x199/0x830
  [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570
  [<ffffffff815ba96f>] ip_finish_output+0x5df/0x870
  [<ffffffff815ba4bd>] ? ip_finish_output+0x12d/0x870
  [<ffffffff815bb964>] ip_output+0x54/0xf0
  [<ffffffff815bad48>] ip_local_out+0x28/0x90
  [<ffffffff815bc444>] ip_send_skb+0x14/0x50
  [<ffffffff815bc4b2>] ip_push_pending_frames+0x32/0x40
  [<ffffffff815e536a>] raw_sendmsg+0x93a/0xc30
  [<ffffffff8128d570>] ? selinux_file_send_sigiotask+0x1f0/0x1f0
  [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80
  [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220
  [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80
  [<ffffffff815f6855>] inet_sendmsg+0x125/0x240
  [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220
  [<ffffffff8155cddb>] sock_sendmsg+0xab/0xe0
  [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0
  [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0
  [<ffffffff8155d18c>] __sys_sendmsg+0x37c/0x390
  [<ffffffff81195b2a>] ? fsnotify+0x2ca/0x7e0
  [<ffffffff811958e8>] ? fsnotify+0x88/0x7e0
  [<ffffffff81361f36>] ? put_ldisc+0x56/0xd0
  [<ffffffff8116f98a>] ? fget_light+0x3da/0x510
  [<ffffffff8155f6c4>] sys_sendmsg+0x44/0x80
  [<ffffffff8172fc22>] system_call_fastpath+0x16/0x1b

Avoid this problem using a distinct lock_class_key for bonding
devices.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-04 15:53:48 -04:00
Jiri Bohac da210f5590 bonding: add some slack to arp monitoring time limits
Currently, all the time limits in the bonding ARP monitor are in
multiples of arp_interval -- the time interval at which the ARP
monitor is periodically scheduled.

With a fast network round-trip and a little scheduling latency
of the ARP monitor work, a limit of n*delta_in_ticks may
effectively mean (n-1)*delta_in_ticks.

This is fatal in case of n==1  (the link will stay down
forever) and makes the behaviour non-deterministic in all the
other cases.

Add a delta_in_ticks/2 time slack to all the time limits.

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-31 16:37:12 -04:00
John Eaglesham 6b923cb718 bonding: support for IPv6 transmit hashing
Currently the "bonding" driver does not support load balancing outgoing
traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4)
are currently supported; this patch adds transmit hashing for IPv6 (and
TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the
bonding driver. In addition, bounds checking has been added to all
transmit hashing functions.

The algorithm chosen (xor'ing the bottom three quads of the source and
destination addresses together, then xor'ing each byte of that result into
the bottom byte, finally xor'ing with the last bytes of the MAC addresses)
was selected after testing almost 400,000 unique IPv6 addresses harvested
from server logs. This algorithm had the most even distribution for both
big- and little-endian architectures while still using few instructions. Its
behavior also attempts to closely match that of the IPv4 algorithm.

The IPv6 flow label was intentionally not included in the hash as it appears
to be unset in the vast majority of IPv6 traffic sampled, and the current
algorithm not using the flow label already offers a very even distribution.

Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets,
ie, they are not balanced based on layer 4 information. Additionally,
IPv6 packets with intermediate headers are not balanced based on layer
4 information. In practice these intermediate headers are not common and
this should not cause any problems, and the alternative (a packet-parsing
loop and look-up table) seemed slow and complicated for little gain.

Tested-by: John Eaglesham <linux@8192.net>
Signed-off-by: John Eaglesham <linux@8192.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-22 22:49:30 -07:00
David S. Miller 1304a7343b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2012-08-22 14:21:38 -07:00
Amerigo Wang e15c3c2294 netpoll: check netpoll tx status on the right device
Although this doesn't matter actually, because netpoll_tx_running()
doesn't use the parameter, the code will be more readable.

For team_dev_queue_xmit() we have to move it down to avoid
compile errors.

Cc: David Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-14 14:33:32 -07:00
Amerigo Wang 38e6bc185d netpoll: make __netpoll_cleanup non-block
Like the previous patch, slave_disable_netpoll() and __netpoll_cleanup()
may be called with read_lock() held too, so we should make them
non-block, by moving the cleanup and kfree() to call_rcu_bh() callbacks.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-14 14:33:30 -07:00
Amerigo Wang 47be03a28c netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-14 14:33:30 -07:00
Amerigo Wang b7bc2a5b5b net: remove netdev_bonding_change()
I don't see any benifits to use netdev_bonding_change() than
using call_netdevice_notifiers() directly.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-14 14:28:24 -07:00
Jiri Pirko 8a540ff9e1 bond_sysfs: use real_num_tx_queues rather than params.tx_queue
Since now number of tx queues can be specified during bond instance
creation and therefore it may differ from params.tx_queues, use rather
real_num_tx_queues for boundary check.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-20 11:07:00 -07:00
Jiri Pirko df4ab5b3c2 net: rename bond_queue_mapping to slave_dev_queue_mapping
As this is going to be used not only by bonding.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-20 11:07:00 -07:00
Jiri Pirko d40156aa5e rtnl: allow to specify different num for rx and tx queue count
Also cut out unused function parameters and possible err in return
value.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-20 11:06:59 -07:00
Eric Dumazet b6fe83e952 bonding: refine IFF_XMIT_DST_RELEASE capability
Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.

bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.

If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-18 09:31:25 -07:00
Jiri Pirko 30fdd8a082 netpoll: move np->dev and np->dev_name init into __netpoll_setup()
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17 09:02:36 -07:00
David S. Miller 04c9f416e3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	net/batman-adv/bridge_loop_avoidance.c
	net/batman-adv/bridge_loop_avoidance.h
	net/batman-adv/soft-interface.c
	net/mac80211/mlme.c

With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).

The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-10 23:56:33 -07:00
Eric W. Biederman 96ca7ffe74 bonding: debugfs and network namespaces are incompatible
The bonding debugfs support has been broken in the presence of network
namespaces since it has been added.  The debugfs support does not handle
multiple bonding devices with the same name in different network
namespaces.

I haven't had any bug reports, and I'm not interested in getting any.
Disable the debugfs support when network namespaces are enabled.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-09 14:49:15 -07:00
Eric W. Biederman a64d49c3dd bonding: Manage /proc/net/bonding/ entries from the netdev events
It was recently reported that moving a bonding device between network
namespaces causes warnings from /proc.  It turns out after the move we
were trying to add and to remove the /proc/net/bonding entries from the
wrong network namespace.

Move the bonding /proc registration code into the NETDEV_REGISTER and
NETDEV_UNREGISTER events where the proc registration and unregistration
will always happen at the right time.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-09 14:49:15 -07:00
David S. Miller e486463e82 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/usb/qmi_wwan.c
	net/batman-adv/translation-table.c
	net/ipv6/route.c

qmi_wwan.c resolution provided by Bjørn Mork.

batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.

ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-25 15:50:32 -07:00
Amerigo Wang df2bcc4af2 bonding: show all the link status of slaves
There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:

	(slave->link == BOND_LINK_UP) ?  "up" : "down"

It doesn't respect the rest two statuses. This patch fixes it.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-17 16:23:54 -07:00
Eric Dumazet 0450243096 bonding: drop_monitor aware
When packets are dropped in TX path, its better to use kfree_skb()
instead of dev_kfree_skb() to give proper drop_monitor events.

Also move the kfree_skb() call after read_unlock() in bond_alb_xmit()
and bond_xmit_activebackup()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-13 16:00:26 -07:00
David S. Miller 43b03f1f6d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	MAINTAINERS
	drivers/net/wireless/iwlwifi/pcie/trans.c

The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.

The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 21:59:18 -07:00
Eric Dumazet de063b7040 bonding: remove packet cloning in recv_probe()
Cloning all packets in input path have a significant cost.

Use skb_header_pointer()/skb_copy_bits() instead of pskb_may_pull() so
that recv_probe handlers (bond_3ad_lacpdu_recv / bond_arp_rcv /
rlb_arp_recv ) dont touch input skb.

bond_handle_frame() can avoid the skb_clone()/dev_kfree_skb()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 18:51:09 -07:00
Eric Dumazet 5ee31c6898 bonding: Fix corrupted queue_mapping
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping.  This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.

When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit.  In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.

Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping.  In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.

If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)

This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :

netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.

Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.

Based on a previous patch from Tom Herbert.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 15:29:21 -07:00
Weiping Pan 8a93664df9 bonding:record primary when modify it via sysfs
If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().

Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 15:23:11 -07:00
David S. Miller 028940342a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2012-05-16 22:17:37 -04:00
David S. Miller b99215cdc6 bonding: Fix LACPDU rx_dropped commit.
I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8cd ("bonding: don't increase
rx_dropped after processing LACPDUs")

I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.

This inter-diffs such that the warnings are now gone.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-13 15:45:13 -04:00
Joe Perches a6700db179 net, drivers/net: Convert compare_ether_addr_64bits to ether_addr_equal_64bits
Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.

Done via cocci script:

$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
-	!compare_ether_addr_64bits(a, b)
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	compare_ether_addr_64bits(a, b)
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal_64bits(a, b) == 0
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal_64bits(a, b) != 0
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	ether_addr_equal_64bits(a, b) == 0
+	!ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	ether_addr_equal_64bits(a, b) != 0
+	ether_addr_equal_64bits(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal_64bits(a, b)
+	ether_addr_equal_64bits(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-10 23:33:01 -04:00
Joe Perches 2e42e4747e drivers/net: Convert compare_ether_addr to ether_addr_equal
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-10 23:33:01 -04:00
Jiri Bohac 13a8e0c8cd bonding: don't increase rx_dropped after processing LACPDUs
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER.  As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.

Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-10 23:30:01 -04:00
Rick Jones 13b95fb714 bonding: bond_update_speed_duplex() can return void since no callers check its return
As none of the callers of bond_update_speed_duplex (need to) check its
return value, there is little point in it returning anything.

Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-27 00:03:35 -04:00
Michal Kubeček f31c7937c2 bonding: start slaves with link down for ARP monitor
Initialize slave device link state as down if ARP monitor is
active and net_carrier_ok() returns zero. Also shift initial
value of its last_arp_tx so that it doesn't immediately cause
fake detection of "up" state.

When ARP monitoring is used, initializing the slave device with
up link state can cause ARP monitor to detect link failure
before the device is really up (with igb driver, this can take
more than two seconds).

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-19 15:25:02 -04:00
David S. Miller 64d683c582 bonding: Fixup get_tx_queue() op second arg type.
I missed this when fixing up the warning in the previous commit.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-13 15:02:35 -04:00
stephen hemminger efacb309b5 rtnetlink & bonding: change args got get_tx_queues
Change get_tx_queues, drop unsused arg/return value real_tx_queues,
and use return by value (with error) rather than call by reference.

Probably bonding should just change to LLTX and the whole get_tx_queues
API could disappear!

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-13 13:31:00 -04:00
Veaceslav Falico 5a4309746c bonding: properly unset current_arp_slave on slave link up
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.

To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-05 19:07:59 -04:00
Shlomo Pongratz 234bcf8a49 net/bonding: correctly proxy slave neigh param setup ndo function
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.

Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.

Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-04 18:11:12 -04:00
Shlomo Pongratz 2af73d4b2a net/bonding: emit address change event also in bond_release
commit 7d26bb103c "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).

Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-04 18:11:12 -04:00
Linus Torvalds ed359a3b7b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Provide device string properly for USB i2400m wimax devices, also
    don't OOPS when providing firmware string.  From Phil Sutter.

 2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.

 3) Add another device ID to USB zaurus driver, from Guan Xin.

 4) Loop index start in pool vector iterator is wrong causing MAC to not
    get configured in bnx2x driver, fix from Dmitry Kravkov.

 5) EQL driver assumes HZ=100, fix from Eric Dumazet.

 6) Now that skb_add_rx_frag() can specify the truesize increment
    separately, do so in f_phonet and cdc_phonet, also from Eric
    Dumazet.

 7) virtio_net accidently uses net_ratelimit() not only on the kernel
    warning but also the statistic bump, fix from Rick Jones.

 8) ip_route_input_mc() uses fixed init_net namespace, oops, use
    dev_net(dev) instead.  Fix from Benjamin LaHaise.

 9) dev_forward_skb() needs to clear the incoming interface index of the
    SKB so that it looks like a new incoming packet, also from Benjamin
    LaHaise.

10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
    5GHZ, fix from Stanislav Yakovlev.

11) Missing kmalloc() return value checks in orinoco, from Santosh
    Nayak.

12) ath9k doesn't check for HT capabilities in the right way, it is
    checking ht_supported instead of the ATH9K_HW_CAP_HT flag.  Fix from
    Sujith Manoharan.

13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
    instructions, from Feiran Zhuang.

14) Avoid infinite loop in GARP code when registering sysfs entries.
    From David Ward.

15) rose protocol uses memcpy instead of memcmp in a device address
    comparison, oops.  Fix from Daniel Borkmann.

16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
    renamed to eth_hw_addr_random().  From Roland Stigge.

17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
    that ipv4 does.  Fix from Shmulik Ladkani.

18) via-rhine has an inverted bit test, causing suspend/resume
    regressions.  Fix from Andreas Mohr.

19) RIONET assumes 4K page size, fix from Akinobu Mita.

20) Initialization of imask register in sky2 is buggy, because bits are
    "or'd" into an uninitialized local variable.  Fix from Lino
    Sanfilippo.

21) Fix FCOE checksum offload handling, from Yi Zou.

22) Fix VLAN processing regression in e1000, from Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  sky2: dont overwrite settings for PHY Quick link
  tg3: Fix 5717 serdes powerdown problem
  net: usb: cdc_eem: fix mtu
  net: sh_eth: fix endian check for architecture independent
  usb/rtl8150 : Remove duplicated definitions
  rionet: fix page allocation order of rionet_active
  via-rhine: fix wait-bit inversion.
  ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
  net: lpc_eth: Fix rename of dev_hw_addr_random
  net/netfilter/nfnetlink_acct.c: use linux/atomic.h
  rose_dev: fix memcpy-bug in rose_set_mac_address
  Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
  net/garp: avoid infinite loop if attribute already exists
  x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
  bonding: emit event when bonding changes MAC
  mac80211: fix oper channel timestamp updation
  ath9k: Use HW HT capabilites properly
  MAINTAINERS: adding maintainer for ipw2x00
  net: orinoco: add error handling for failed kmalloc().
  net/wireless: ipw2x00: fix a typo in wiphy struct initilization
  ...
2012-04-02 17:53:39 -07:00
Weiping Pan 7d26bb103c bonding: emit event when bonding changes MAC
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.

Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.

How to reproduce this bug ?

                       -----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24  \--|-- eth1-/                       |
                       --------------------------------

1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1

then eth0 is the active slave, and MAC of bond0 is MAC of eth0.

2 on hostA, ping 192.168.100.2

3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.

4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.

Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-29 18:11:57 -04:00
Linus Torvalds 0195c00244 Disintegrate and delete asm/system.h
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAT3NKzROxKuMESys7AQKElw/+JyDxJSlj+g+nymkx8IVVuU8CsEwNLgRk
 8KEnRfLhGtkXFLSJYWO6jzGo16F8Uqli1PdMFte/wagSv0285/HZaKlkkBVHdJ/m
 u40oSjgT013bBh6MQ0Oaf8pFezFUiQB5zPOA9QGaLVGDLXCmgqUgd7exaD5wRIwB
 ZmyItjZeAVnDfk1R+ZiNYytHAi8A5wSB+eFDCIQYgyulA1Igd1UnRtx+dRKbvc/m
 rWQ6KWbZHIdvP1ksd8wHHkrlUD2pEeJ8glJLsZUhMm/5oMf/8RmOCvmo8rvE/qwl
 eDQ1h4cGYlfjobxXZMHqAN9m7Jg2bI946HZjdb7/7oCeO6VW3FwPZ/Ic75p+wp45
 HXJTItufERYk6QxShiOKvA+QexnYwY0IT5oRP4DrhdVB/X9cl2MoaZHC+RbYLQy+
 /5VNZKi38iK4F9AbFamS7kd0i5QszA/ZzEzKZ6VMuOp3W/fagpn4ZJT1LIA3m4A9
 Q0cj24mqeyCfjysu0TMbPtaN+Yjeu1o1OFRvM8XffbZsp5bNzuTDEvviJ2NXw4vK
 4qUHulhYSEWcu9YgAZXvEWDEM78FXCkg2v/CrZXH5tyc95kUkMPcgG+QZBB5wElR
 FaOKpiC/BuNIGEf02IZQ4nfDxE90QwnDeoYeV+FvNj9UEOopJ5z5bMPoTHxm4cCD
 NypQthI85pc=
 =G9mT
 -----END PGP SIGNATURE-----

Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system

Pull "Disintegrate and delete asm/system.h" from David Howells:
 "Here are a bunch of patches to disintegrate asm/system.h into a set of
  separate bits to relieve the problem of circular inclusion
  dependencies.

  I've built all the working defconfigs from all the arches that I can
  and made sure that they don't break.

  The reason for these patches is that I recently encountered a circular
  dependency problem that came about when I produced some patches to
  optimise get_order() by rewriting it to use ilog2().

  This uses bitops - and on the SH arch asm/bitops.h drags in
  asm-generic/get_order.h by a circuituous route involving asm/system.h.

  The main difficulty seems to be asm/system.h.  It holds a number of
  low level bits with no/few dependencies that are commonly used (eg.
  memory barriers) and a number of bits with more dependencies that
  aren't used in many places (eg.  switch_to()).

  These patches break asm/system.h up into the following core pieces:

    (1) asm/barrier.h

        Move memory barriers here.  This already done for MIPS and Alpha.

    (2) asm/switch_to.h

        Move switch_to() and related stuff here.

    (3) asm/exec.h

        Move arch_align_stack() here.  Other process execution related bits
        could perhaps go here from asm/processor.h.

    (4) asm/cmpxchg.h

        Move xchg() and cmpxchg() here as they're full word atomic ops and
        frequently used by atomic_xchg() and atomic_cmpxchg().

    (5) asm/bug.h

        Move die() and related bits.

    (6) asm/auxvec.h

        Move AT_VECTOR_SIZE_ARCH here.

  Other arch headers are created as needed on a per-arch basis."

Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that.  We'll find out anything that got broken and fix it..

* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
  Delete all instances of asm/system.h
  Remove all #inclusions of asm/system.h
  Add #includes needed to permit the removal of asm/system.h
  Move all declarations of free_initmem() to linux/mm.h
  Disintegrate asm/system.h for OpenRISC
  Split arch_align_stack() out from asm-generic/system.h
  Split the switch_to() wrapper out of asm-generic/system.h
  Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
  Create asm-generic/barrier.h
  Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
  Disintegrate asm/system.h for Xtensa
  Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
  Disintegrate asm/system.h for Tile
  Disintegrate asm/system.h for Sparc
  Disintegrate asm/system.h for SH
  Disintegrate asm/system.h for Score
  Disintegrate asm/system.h for S390
  Disintegrate asm/system.h for PowerPC
  Disintegrate asm/system.h for PA-RISC
  Disintegrate asm/system.h for MN10300
  ...
2012-03-28 15:58:21 -07:00
David Howells 9ffc93f203 Remove all #inclusions of asm/system.h
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`

Signed-off-by: David Howells <dhowells@redhat.com>
2012-03-28 18:30:03 +01:00
Andy Gospodarek eaddcd7690 bonding: remove entries for master_ip and vlan_ip and query devices instead
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.

        commit 917fbdb32f
        Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
        Date:   Wed Nov 23 23:37:15 2011 +0000

            bonding: only use primary address for ARP

That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address.  Unfortunately, it
didn't always work as expected.

When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address.  The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten.  The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.

This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once.  The
inconsistent behavior between those two interfaces was something that
needed to be resolved.

While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver.  I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.

As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address.  This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.

I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.

Thanks to Ralf for all his help on this.

v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.

v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 22:36:17 -04:00
Peter Pan(潘卫平) 1c3ac4289a bonding: send igmp report for its master
Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.

eth0--
      |-- bond0 -- br0
eth1--

modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1

brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0

Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.

The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.

If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.

Instead I choose to modify bonding to send igmp report for its master.

Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-19 18:02:05 -04:00
Jesper Juhl b9d6d2dbf4 bonding: Fix misspelling of "since"
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-05 22:42:00 -05:00
Joe Perches e404decb0f drivers/net: Remove unnecessary k.alloc/v.alloc OOM messages
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.

Remove the allocation failure messages.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31 16:20:21 -05:00
Jiri Bohac b924551bed bonding: fix enslaving in alb mode when link down
bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC
address. This is done differently for TLB and ALB modes.
bond->alb_info.rlb_enabled is used to discriminate between the two modes but
this flag may be uninitialized if the slave is being enslaved prior to calling
bond_open() -> bond_alb_initialize() on the master.

It turns out all the callers of alb_set_slave_mac_addr() pass
bond->alb_info.rlb_enabled as the hw parameter.

This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and
makes the function decide based on the bonding mode instead, which fixes the
above problem.

Reported-by: Narendra K <Narendra_K@Dell.com>
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-18 20:59:53 -05:00
Maxim Uvarov f515e6b770 bond_alb: don't disable softirq under bond_alb_xmit
No need to lock soft irqs under bond_alb_xmit()
which already has softirq disabled.

Changes:
1. add non-bh/bh version to tlb_clear_slave()

2. represent BH and non BH hash table locks
_lock_rx_hashtbl_bh/_unlock_rx_hashtbl_bh
_lock_rx_hashtbl/_unlock_rx_hashtbl
_lock_tx_hashtbl_bh/_unlock_tx_hashtbl_bh
_lock_tx_hashtbl/_unlock_tx_hashtbl

Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-11 12:52:26 -08:00
Linus Torvalds 7affca3537 Merge branch 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
  arm: fix up some samsung merge sysdev conversion problems
  firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
  Drivers:hv: Fix a bug in vmbus_driver_unregister()
  driver core: remove __must_check from device_create_file
  debugfs: add missing #ifdef HAS_IOMEM
  arm: time.h: remove device.h #include
  driver-core: remove sysdev.h usage.
  clockevents: remove sysdev.h
  arm: convert sysdev_class to a regular subsystem
  arm: leds: convert sysdev_class to a regular subsystem
  kobject: remove kset_find_obj_hinted()
  m86k: gpio - convert sysdev_class to a regular subsystem
  mips: txx9_sram - convert sysdev_class to a regular subsystem
  mips: 7segled - convert sysdev_class to a regular subsystem
  sh: dma - convert sysdev_class to a regular subsystem
  sh: intc - convert sysdev_class to a regular subsystem
  power: suspend - convert sysdev_class to a regular subsystem
  power: qe_ic - convert sysdev_class to a regular subsystem
  power: cmm - convert sysdev_class to a regular subsystem
  s390: time - convert sysdev_class to a regular subsystem
  ...

Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
 - arch/arm/mach-exynos/cpu.c
 - arch/arm/mach-exynos/irq-eint.c
 - arch/arm/mach-s3c64xx/common.c
 - arch/arm/mach-s3c64xx/cpu.c
 - arch/arm/mach-s5p64x0/cpu.c
 - arch/arm/mach-s5pv210/common.c
 - arch/arm/plat-samsung/include/plat/cpu.h
 - arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
2012-01-07 12:03:30 -08:00
Greg Kroah-Hartman ff4b8a57f0 Merge branch 'driver-core-next' into Linux 3.2
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.

The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-06 11:42:52 -08:00
stephen hemminger f7d9821a6a bonding: fix error handling if slave is busy (v2)
If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.

The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves

The fix is to detach the slave (which removes it from the list)
in the unwind path.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-03 12:49:16 -05:00
Kay Sievers edbaa603eb driver-core: remove sysdev.h usage.
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.

The sysdev code will be going away soon, so this include needs to be
removed no matter what.

Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
2011-12-21 16:26:03 -08:00
Jiri Pirko 87002b03ba net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls
This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:52:42 -05:00
Jiri Pirko 8e586137e6 net: make vlan ndo_vlan_rx_[add/kill]_vid return error value
Let caller know the result of adding/removing vlan id to/from vlan
filter.

In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-08 19:52:37 -05:00
David S. Miller b3613118eb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2011-12-02 13:49:21 -05:00
Henrik Saavedra Persson 917fbdb32f bonding: only use primary address for ARP
Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.

Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
2011-11-30 22:59:11 -05:00
Ben Hutchings 4f5762ec91 bonding: Remove obsolete source file 'bond_ipv6.c'
This file is now unused and should have been removed by commit
7c89943236 ("bonding, ipv4, ipv6, vlan:
Handle NETDEV_BONDING_FAILOVER like NETDEV_NOTIFY_PEERS").

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-26 14:50:05 -05:00
Alexey Dobriyan 4e3fd7a06d net: remove ipv6_addr_copy()
C assignment can handle struct in6_addr copying.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-22 16:43:32 -05:00
David S. Miller efd0bf97de Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.

The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.

Conflicts:
	drivers/net/ethernet/nvidia/forcedeth.c
	drivers/net/wireless/libertas/cfg.c
2011-11-21 13:50:33 -05:00
Veaceslav Falico 4a8bb7e27f bonding: Don't allow mode change via sysfs with slaves present
When changing mode via bonding's sysfs, the slaves are not initialized
correctly. Forbid to change modes with slaves present to ensure that every
slave is initialized correctly via bond_enslave().

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-17 19:31:54 -05:00
Michał Mirosław 34324dc2bf net: remove NETIF_F_NO_CSUM feature bit
Only distinct use is checking if NETIF_F_NOCACHE_COPY should be
enabled by default. The check heuristics is altered a bit here,
so it hits other people than before. The default shouldn't be
trusted for performance-critical cases anyway.

For all other uses NETIF_F_NO_CSUM is equivalent to NETIF_F_HW_CSUM.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 17:43:12 -05:00
Michał Mirosław c8f44affb7 net: introduce and use netdev_features_t for device features sets
v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 17:43:10 -05:00
Linus Torvalds 94956eed14 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
  forcedeth: fix a few sparse warnings (variable shadowing)
  forcedeth: Improve stats counters
  forcedeth: remove unneeded stats updates
  forcedeth: Acknowledge only interrupts that are being processed
  forcedeth: fix race when unloading module
  MAINTAINERS/rds: update maintainer
  wanrouter: Remove kernel_lock annotations
  usbnet: fix oops in usbnet_start_xmit
  ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
  etherh: Add MAINTAINERS entry for etherh
  bonding: comparing a u8 with -1 is always false
  sky2: fix regression on Yukon Optima
  netlink: clarify attribute length check documentation
  netlink: validate NLA_MSECS length
  i825xx:xscale:8390:freescale: Fix Kconfig dependancies
  macvlan: receive multicast with local address
  tg3: Update version to 3.121
  tg3: Eliminate timer race with reset_task
  tg3: Schedule at most one tg3_reset_task run
  tg3: Obtain PCI function number from device
  ...
2011-11-07 10:55:33 -08:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
Dan Carpenter 589665f5a6 bonding: comparing a u8 with -1 is always false
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-04 18:37:23 -04:00
Weiping Pan 98f41f694f bonding:update speed/duplex for NETDEV_CHANGE
Zheng Liang(lzheng@redhat.com) found a bug that if we config bonding with
arp monitor, sometimes bonding driver cannot get the speed and duplex from
its slaves, it will assume them to be 100Mb/sec and Full, please see
/proc/net/bonding/bond0.
But there is no such problem when uses miimon.

(Take igb for example)
I find that the reason is that after dev_open() in bond_enslave(),
bond_update_speed_duplex() will call igb_get_settings()
, but in that function,
it runs ethtool_cmd_speed_set(ecmd, -1); ecmd->duplex = -1;
because igb get an error value of status.
So even dev_open() is called, but the device is not really ready to get its
settings.

Maybe it is safe for us to call igb_get_settings() only after
this message shows up, that is "igb: p4p1 NIC Link is Up 1000 Mbps Full Duplex,
Flow Control: RX".

So I prefer to update the speed and duplex for a slave when reseices
NETDEV_CHANGE/NETDEV_UP event.

Changelog
V2:
1 remove the "fake 100/Full" logic in bond_update_speed_duplex(),
  set speed and duplex to -1 when it gets error value of speed and duplex.
2 delete the warning in bond_enslave() if bond_update_speed_duplex() returns
  error.
3 make bond_info_show_slave() handle bad values of speed and duplex.

Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-01 17:52:49 -04:00
Paul Gortmaker ee40fa0656 drivers/net: Add export.h to files using EXPORT_SYMBOL/THIS_MODULE
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c

This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:08 -04:00
Jay Vosburgh e6d265e850 bonding: eliminate bond_close race conditions
This patch resolves two sets of race conditions.

	Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the
first, as follows:

The bond_close() calls cancel_delayed_work() to cancel delayed works.
It, however, cannot cancel works that were already queued in workqueue.
The bond_open() initializes work->data, and proccess_one_work() refers
get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when
work->data has been initialized. Thus, a panic occurs.

	He included a patch that converted the cancel_delayed_work calls
in bond_close to flush_delayed_work_sync, which eliminated the above
problem.

	His patch is incorporated, at least in principle, into this
patch.  In this patch, we use cancel_delayed_work_sync in place of
flush_delayed_work_sync, and also convert bond_uninit in addition to
bond_close.

	This conversion to _sync, however, opens new races between
bond_close and three periodically executing workqueue functions:
bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon.

	The race occurs because bond_close and bond_uninit are always
called with RTNL held, and these workqueue functions may acquire RTNL to
perform failover-related activities.  If bond_close or bond_uninit is
waiting in cancel_delayed_work_sync, deadlock occurs.

	These deadlocks are resolved by having the workqueue functions
acquire RTNL conditionally.  If the rtnl_trylock() fails, the functions
reschedule and return immediately.  For the cases that are attempting to
perform link failover, a delay of 1 is used; for the other cases, the
normal interval is used (as those activities are not as time critical).

	Additionally, the bond_mii_monitor function now stores the delay
in a variable (mimicing the structure of activebackup_arp_mon).

	Lastly, all of the above renders the kill_timers sentinel moot,
and therefore it has been removed.

Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-30 03:13:14 -04:00
Maciej Żenczykowski 59fdaca9a4 net: make bonding slaves honour master's skb->priority
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-25 19:22:23 -04:00
David S. Miller 1805b2f048 Merge branch 'master' of ra.kernel.org:/pub/scm/linux/kernel/git/davem/net 2011-10-24 18:18:09 -04:00
Eric W. Biederman 01718e36df bonding: Add a forgetten sysfs_attr_init on class_attr_bonding_masters
When I made class_attr_bonding_matters per network namespace and dynamically
allocated I overlooked the need for calling sysfs_attr_init.  Oops.

This fixes the following lockdep splat:

[    5.749651] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[    5.749655] bonding: MII link monitoring set to 100 ms
[    5.749676] BUG: key f49a831c not in .data!
[    5.749677] ------------[ cut here ]------------
[    5.749752] WARNING: at kernel/lockdep.c:2897 lockdep_init_map+0x1c3/0x460()
[    5.749809] Hardware name: ProLiant BL460c G1
[    5.749862] Modules linked in: bonding(+)
[    5.749978] Pid: 3177, comm: modprobe Not tainted 3.1.0-rc9-02177-gf2d1a4e-dirty #1157
[    5.750066] Call Trace:
[    5.750120]  [<c1352c2f>] ? printk+0x18/0x21
[    5.750176]  [<c103112d>] warn_slowpath_common+0x6d/0xa0
[    5.750231]  [<c1060133>] ? lockdep_init_map+0x1c3/0x460
[    5.750287]  [<c1060133>] ? lockdep_init_map+0x1c3/0x460
[    5.750342]  [<c103117d>] warn_slowpath_null+0x1d/0x20
[    5.750398]  [<c1060133>] lockdep_init_map+0x1c3/0x460
[    5.750453]  [<c1355ddd>] ? _raw_spin_unlock+0x1d/0x20
[    5.750510]  [<c11255c8>] ? sysfs_new_dirent+0x68/0x110
[    5.750565]  [<c1124d4b>] sysfs_add_file_mode+0x8b/0xe0
[    5.750621]  [<c1124db3>] sysfs_add_file+0x13/0x20
[    5.750675]  [<c1124e7c>] sysfs_create_file+0x1c/0x20
[    5.750737]  [<c1208f09>] class_create_file+0x19/0x20
[    5.750794]  [<c12c186f>] netdev_class_create_file+0xf/0x20
[    5.750853]  [<f85deaf4>] bond_create_sysfs+0x44/0x90 [bonding]
[    5.750911]  [<f8410947>] ? bond_create_proc_dir+0x1e/0x3e [bonding]
[    5.750970]  [<f841007e>] bond_net_init+0x7e/0x87 [bonding]
[    5.751026]  [<f8410000>] ? 0xf840ffff
[    5.751080]  [<c12abc7a>] ops_init.clone.4+0xba/0x100
[    5.751135]  [<c12abdb2>] ? register_pernet_subsys+0x12/0x30
[    5.751191]  [<c12abd03>] register_pernet_operations.clone.3+0x43/0x80
[    5.751249]  [<c12abdb9>] register_pernet_subsys+0x19/0x30
[    5.751306]  [<f84108b9>] bonding_init+0x832/0x8a2 [bonding]
[    5.751363]  [<c10011f0>] do_one_initcall+0x30/0x160
[    5.751420]  [<f8410087>] ? bond_net_init+0x87/0x87 [bonding]
[    5.751477]  [<c106d5cf>] sys_init_module+0xef/0x1890
[    5.751533]  [<c1356490>] sysenter_do_call+0x12/0x36
[    5.751588] ---[ end trace 89f492d83a7f5006 ]---

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-22 05:08:44 -04:00
Eric W. Biederman 4c22400ab6 bonding: Use a per netns implementation of /sys/class/net/bonding_masters.
This fixes a network namespace misfeature that bonding_masters looked at
current instead of the remembering the context where in which
/sys/class/net/bonding_masters was opened in to see which network
namespace to act upon.

This removes the need for sysfs to handle tagged directories with
untagged members allowing for a conceptually simpler sysfs
implementation.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-19 19:24:15 -04:00
Flavio Leitner d5edf2906e bonding: fix wrong port enabling in 802.3ad
The port shouldn't be enabled unless its current MUX
state is DISTRIBUTING which is correctly handled by
ad_mux_machine(), otherwise the packet sent can be
lost because the other end may not be ready.

The issue happens on every port initialization, but
as the ports are expected to move quickly to DISTRIBUTING,
it doesn't cause much problem.  However, it does cause
constant packet loss if the other peer has the port
configured to stay in STANDBY (i.e. SYNC set to OFF).

Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-19 19:24:14 -04:00
Mitsuo Hayasaka 4d97480b18 bonding: use local function pointer of bond->recv_probe in bond_handle_frame
The bond->recv_probe is called in bond_handle_frame() when
a packet is received, but bond_close() sets it to NULL. So,
a panic occurs when both functions work in parallel.

Why this happen:
After null pointer check of bond->recv_probe, an sk_buff is
duplicated and bond->recv_probe is called in bond_handle_frame.
So, a panic occurs when bond_close() is called between the
check and call of bond->recv_probe.

Patch:
This patch uses a local function pointer of bond->recv_probe
in bond_handle_frame(). So, it can avoid the null pointer
dereference.

Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-19 00:14:22 -04:00
David S. Miller 88c5100c28 Merge branch 'master' of github.com:davem330/net
Conflicts:
	net/batman-adv/soft-interface.c
2011-10-07 13:38:43 -04:00
Andy Gospodarek a0db2dad09 bonding: properly stop queuing work when requested
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed.  I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.

There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first.  There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.

This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set.  I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Liang Zheng <lzheng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-03 13:48:20 -04:00
Jiri Pirko 4bc71cb983 net: consolidate and fix ethtool_ops->get_settings calling
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
  from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
  iboe_get_rate was previously ->get_settings() called unlocked. This
  fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
  problem. Also fixed by calling __dev_get_by_index() instead of
  dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
  so bnx2fc_if_create() and fcoe_if_create() are called locked as they
  are from other places.
- use __ethtool_get_settings() in bonding code

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

v2->v3:
	-removed dev_ethtool_get_settings()
	-added ASSERT_RTNL into __ethtool_get_settings()
	-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
	 around it and __ethtool_get_settings() call
v1->v2:
        add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15 17:32:26 -04:00
David S. Miller 823dcd2506 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net 2011-08-20 10:39:12 -07:00
Jiri Pirko afc4b13df1 net: remove use of ndo_set_multicast_list in drivers
replace it by ndo_set_rx_mode

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:22:03 -07:00
Jiri Pirko d03462b999 bonding: use ndo_change_rx_flags callback
Benefit from use of ndo_change_rx_flags in handling change of promisc
and allmulti. No need to store previous state locally.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:17:47 -07:00
Peter Pan(潘卫平) ba3211ccd0 bonding:reset backup and inactive flag of slave
Eduard Sinelnikov (eduard.sinelnikov@gmail.com) found that if we change
bonding mode from active backup to round robin, some slaves are still keeping
"backup", and won't transmit packets.

As Jay Vosburgh(fubar@us.ibm.com) pointed out that we can work around that by
removing the bond_is_active_slave() check, because the "backup" flag is only
meaningful for active backup mode.

But if we just simply ignore the bond_is_active_slave() check,
the transmission will work fine, but we can't maintain the correct value of
"backup" flag for each slaves, though it is meaningless for other mode than
active backup.

I'd like to reset "backup" and "inactive" flag in bond_open,
thus we can keep the correct value of them.

As for bond_is_active_slave(), I'd like to prepare another patch to handle it.

V2:
Use C style comment.
Move read_lock(&bond->curr_slave_lock).
Replace restore with reset, for active backup mode, it means "restore",
but for other modes, it means "reset".

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17 20:12:06 -07:00
Jiri Pirko d5da4510a7 bonding: implement get_tx_queues rtnk_link_op
If bonding device is created via rtnl, it is created with default number
of rx/tx queues. This patch implements callback in bonding so the
correct value (previously specified by bonding module param) is used.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-11 07:44:38 -07:00
Andy Gospodarek b2730f4f84 bonding: reduce noise during init
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Andy Gospodarek f4bb2e9c4f bonding: fix string comparison errors
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.

This was reported and based on work by Takuma Umeya.  I also verified
the problem and tested that this fix resolves it.

V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.

I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.

V3: Actually sending the proper patch....

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Neil Horman 550fd08c2c net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs.  There are a handful of drivers that violate this assumption of
course, and need to be fixed up.  This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Jiri Pirko cc0e407006 bonding: do vlan cleanup
Now when all devices are cleaned up, bond can be cleaned up as well

- remove bond->vlgrp
- remove bond_vlan_rx_register
- substitute necessary occurences of vlan_group_get_device

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21 13:47:58 -07:00
David S. Miller 033b1142f4 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/bluetooth/l2cap_core.c
2011-07-21 13:38:42 -07:00
Michał Mirosław 62f2a3a48b net: remove NETIF_F_ALL_TX_OFFLOADS
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.

For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.

This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.

NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-14 15:18:49 -07:00
stephen hemminger 655f8919d5 bonding: add min links parameter to 802.3ad
This adds support for a configuring the minimum number of links that
must be active before asserting carrier. It is similar to the Cisco
EtherChannel min-links feature. This allows setting the minimum number
of member ports that must be up (link-up state) before marking the
bond device as up (carrier on). This is useful for situations where
higher level services such as clustering want to ensure a minimum
number of low bandwidth links are active before switchover.

See:
   http://bugzilla.vyatta.com/show_bug.cgi?id=7196

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-23 02:12:55 -07:00
Paul Gortmaker 56f8a75c17 ip: introduce ip_is_fragment helper inline function
There are enough instances of this:

    iph->frag_off & htons(IP_MF | IP_OFFSET)

that a helper function is probably warranted.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-21 20:33:34 -07:00
David S. Miller 9f6ec8d697 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn-rxon.c
	drivers/net/wireless/rtlwifi/pci.c
	net/netfilter/ipvs/ip_vs_core.c
2011-06-20 22:29:08 -07:00
WANG Cong cefa9993f1 netpoll: copy dev name of slaves to struct netpoll
Otherwise we will not see the name of the slave dev in error
message:

[  388.469446] (null):  doesn't support polling, aborting.

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-19 16:13:01 -07:00
Peter Pan(潘卫平) bf0239a98a bonding:delete a dereference before check
Dan Carpenter found that there was a dereference before a check,
added in 56d00c677de0(bonding:delete lacp_fast from ad_bond_info).

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
2011-06-13 18:29:41 -04:00
Jiri Bohac 830a9c7551 bonding: clean up bond_del_vlan()
1) the setting of NETIF_F_VLAN_CHALLENGED in bond_del_vlan() is
useless since commit b2a103e6 because bond_fix_features() now
sets NETIF_F_VLAN_CHALLENGED whenever the last slave is being
removed.

2) the code never triggers anyway as vlan_list is never empty
since ad1afb00.

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-11 16:13:29 -07:00
Peter Pan(潘卫平) e357964ee6 bonding: delete unused arp_mon_pt
Now all received packets are handled by bond_handle_frame,
and arp_mon_pt isn't used any more.

Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09 15:02:19 -07:00
Peter Pan(潘卫平) 0cc42eb608 bonding: delete unused ad_timer
Now we use agg_select_timer and ad_work.

Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09 15:02:19 -07:00
Peter Pan(潘卫平) 1a14fbcbc9 bonding:delete agg_select_mode from ad_bond_info
bond_params->ad_select and ad_bond_info->agg_select_mode have the same
meaning, they are duplicate and need extra synchronization.

__get_agg_selection_mode() get ad_select from bond_params directly.

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09 15:02:19 -07:00
Peter Pan(潘卫平) 56d00c677d bonding:delete lacp_fast from ad_bond_info
These is also a bug, that if you modify lacp_rate via sysfs,
and add new slaves in bonding, new slaves won't use the latest lacp_rate,
since ad_bond_info->lacp_fast is initialized only once,
in bond_3ad_initialize().

Since both struct bond_params and ad_bond_info have lacp_fast,
they are duplicate and need extra synchronization.

bond_3ad_bind_slave() can use bond_params->lacp_fast to initialize port.
So we can just remove lacp_fast from struct ad_bond_info.

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09 15:02:19 -07:00
Peter Pan(潘卫平) ba824a8b2d bonding: make 802.3ad use latest lacp_rate
There is bug that when you modify lacp_rate via sysfs,
802.3ad won't use the new value of lacp_rate to transmit packets.
This is because port->actor_oper_port_state isn't changed.

Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09 15:02:18 -07:00
Neil Horman 374eeb5a9d bonding: reset queue mapping prior to transmission to physical device (v5)
The bonding driver is multiqueue enabled, in which each queue represents a slave
to enable optional steering of output frames to given slaves against the default
output policy.  However, it needs to reset the skb->queue_mapping prior to
queuing to the physical device or the physical slave (if it is multiqueue) could
wind up transmitting on an unintended tx queue

Change Notes:
v2) Based on first pass review, updated the patch to restore the origional queue
mapping that was found in bond_select_queue, rather than simply resetting to
zero.  This preserves the value of queue_mapping when it was set on receive in
the forwarding case which is desireable.

v3) Fixed spelling an casting error in skb->cb

v4) fixed to store raw queue_mapping to avoid double decrement

v5) Eric D requested that ->cb access be wrapped in a macro.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-05 14:31:25 -07:00
Jiri Pirko 6f92c66f71 bonding: allow all slave speeds
No need to check for 10, 100, 1000, 10000 explicitly. Just make this
generic and check for invalid values only (similar check is in ethtool
userspace app). This enables correct speed handling for slave devices
with "nonstandard" speeds.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-02 14:43:56 -07:00
Andy Gospodarek 90e62474fd bonding: cleanup module option descriptions
Weiping Pan noticed that the module option description for
xmit_hash_policy was incorrect and was nice enough to post a patch to
fix it.  The text was correct, but created a line over 80 characters and
I would rather not add those.  I realized I could take a few minutes and
clean up all the descriptions and things would look much better.  This
is the result.

Based on patch from Weiping Pan <panweiping3@gmail.com>.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-26 14:57:17 -04:00
Flavio Leitner 94265cf5f7 bonding: documentation and code cleanup for resend_igmp
Improves the documentation about how IGMP resend parameter
works, fix two missing checks and coding style issues.

Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-25 17:55:33 -04:00
Neil Horman 9fe0617d9b bonding: prevent deadlock on slave store with alb mode (v3)
This soft lockup was recently reported:

[root@dell-per715-01 ~]# echo +bond5 > /sys/class/net/bonding_masters
[root@dell-per715-01 ~]# echo +eth1 > /sys/class/net/bond5/bonding/slaves
bonding: bond5: doing slave updates when interface is down.
bonding bond5: master_dev is not up in bond_enslave
[root@dell-per715-01 ~]# echo -eth1 > /sys/class/net/bond5/bonding/slaves
bonding: bond5: doing slave updates when interface is down.

BUG: soft lockup - CPU#12 stuck for 60s! [bash:6444]
CPU 12:
Modules linked in: bonding autofs4 hidp rfcomm l2cap bluetooth lockd sunrpc
be2d
Pid: 6444, comm: bash Not tainted 2.6.18-262.el5 #1
RIP: 0010:[<ffffffff80064bf0>]  [<ffffffff80064bf0>]
.text.lock.spinlock+0x26/00
RSP: 0018:ffff810113167da8  EFLAGS: 00000286
RAX: ffff810113167fd8 RBX: ffff810123a47800 RCX: 0000000000ff1025
RDX: 0000000000000000 RSI: ffff810123a47800 RDI: ffff81021b57f6f8
RBP: ffff81021b57f500 R08: 0000000000000000 R09: 000000000000000c
R10: 00000000ffffffff R11: ffff81011d41c000 R12: ffff81021b57f000
R13: 0000000000000000 R14: 0000000000000282 R15: 0000000000000282
FS:  00002b3b41ef3f50(0000) GS:ffff810123b27940(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002b3b456dd000 CR3: 000000031fc60000 CR4: 00000000000006e0

Call Trace:
 [<ffffffff80064af9>] _spin_lock_bh+0x9/0x14
 [<ffffffff886937d7>] :bonding:tlb_clear_slave+0x22/0xa1
 [<ffffffff8869423c>] :bonding:bond_alb_deinit_slave+0xba/0xf0
 [<ffffffff8868dda6>] :bonding:bond_release+0x1b4/0x450
 [<ffffffff8006457b>] __down_write_nested+0x12/0x92
 [<ffffffff88696ae4>] :bonding:bonding_store_slaves+0x25c/0x2f7
 [<ffffffff801106f7>] sysfs_write_file+0xb9/0xe8
 [<ffffffff80016b87>] vfs_write+0xce/0x174
 [<ffffffff80017450>] sys_write+0x45/0x6e
 [<ffffffff8005d28d>] tracesys+0xd5/0xe0

It occurs because we are able to change the slave configuarion of a bond while
the bond interface is down.  The bonding driver initializes some data structures
only after its ndo_open routine is called.  Among them is the initalization of
the alb tx and rx hash locks.  So if we add or remove a slave without first
opening the bond master device, we run the risk of trying to lock/unlock a
spinlock that has garbage for data in it, which results in our above softlock.

Note that sometimes this works, because in many cases an unlocked spinlock has
the raw_lock parameter initialized to zero (meaning that the kzalloc of the
net_device private data is equivalent to calling spin_lock_init), but thats not
true in all cases, and we aren't guaranteed that condition, so we need to pass
the relevant spinlocks through the spin_lock_init function.

Fix it by moving the spin_lock_init calls for the tx and rx hashtable locks to
the ndo_init path, so they are ready for use by the bond_store_slaves path.

Change notes:
v2) Based on conversation with Jay and Nicolas it seems that the ability to
enslave devices while the bond master is down should be safe to do.  As such
this is an outlier bug, and so instead we'll just initalize the errant spinlocks
in the init path rather than the open path, solving the problem.  We'll also
remove the warnings about the bond being down during enslave operations, since
it should be safe

v3) Fix spelling error

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: jtluka@redhat.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: nicolas.2p.debian@gmail.com
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-25 17:55:33 -04:00
Amerigo Wang daf9209bb2 net: rename NETDEV_BONDING_DESLAVE to NETDEV_RELEASE
s/NETDEV_BONDING_DESLAVE/NETDEV_RELEASE/ as Andy suggested.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-22 21:01:19 -04:00
Amerigo Wang 8d8fc29d02 netpoll: disable netpoll when enslave a device
V3: rename NETDEV_ENSLAVE to NETDEV_JOIN

Currently we do nothing when we enslave a net device which is running netconsole.
Neil pointed out that we may get weird results in such case, so let's disable
netpoll on the device being enslaved. I think it is too harsh to prevent
the device being ensalved if it is running netconsole.

By the way, this patch also removes the NETDEV_GOING_DOWN from netconsole
netdev notifier, because netpoll will check if the device is running or not
and we don't handle NETDEV_PRE_UP neither.

This patch is based on net-next-2.6.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-22 21:01:19 -04:00
David S. Miller 9cbc94eabb Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/vmxnet3/vmxnet3_ethtool.c
	net/core/dev.c
2011-05-17 17:33:11 -04:00
Shan Wei 534ea99b06 net: drivers: kill two unused macro definitions
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-15 18:01:15 -04:00
Vitalii Demianets a10e146676 bonding,llc: Fix structure sizeof incompatibility for some PDUs
With some combinations of arch/compiler (e.g. arm-linux-gcc) the sizeof
operator on structure returns value greater than expected. In cases when the
structure is used for mapping PDU fields it may lead to unexpected results
(such as holes and alignment problems in skb data). __packed prevents this
undesired behavior.

Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-13 15:13:24 -04:00
Michał Mirosław b2a103e6d0 bonding: convert to ndo_fix_features
This should also fix updating of vlan_features and propagating changes to
VLAN devices on the bond.

Side effect: it allows user to force-disable some offloads on the bond
interface.

Note: NETIF_F_VLAN_CHALLENGED is managed by bond_fix_features() now.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-12 18:45:59 -04:00
Michał Mirosław 0693e88e6c net: bonding: factor out rlock(bond->lock) in xmit path
Pull read_lock(&bond->lock) and BOND_IS_OK() to bond_start_xmit() from
mode-dependent xmit functions.

netif_running() is always true in hard_start_xmit.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-09 12:05:59 -07:00
Jiri Pirko 1c5cae815d net: call dev_alloc_name from register_netdevice
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.

The possibility to call dev_alloc_name in advance remains.

This also fixes veth creation regresion caused by
84c49d8c3e

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-05 10:57:45 -07:00
Ben Hutchings ad246c992b ipv4, ipv6, bonding: Restore control over number of peer notifications
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.

Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.

Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested.  Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter.  Bump
the bonding version number and update its documentation.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-29 12:44:11 -07:00
David S. Miller 2bd93d7af1 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-26 12:16:46 -07:00
Jiri Pirko 3aba891dde bonding: move processing of recv handlers into handle_frame()
Since now when bonding uses rx_handler, all traffic going into bond
device goes thru bond_handle_frame. So there's no need to go back into
bonding code later via ptype handlers. This patch converts
original ptype handlers into "bonding receive probes". These functions
are called from bond_handle_frame and they are registered per-mode.

Note that vlan packets are also handled because they are always untagged
thanks to vlan_untag()

Note that this also allows arpmon for eth-bond-bridge-vlan topology.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-25 12:00:30 -07:00
Jiri Bohac 2430af8b7f bonding: 802.3ad - fix agg_device_up
The slave member of struct aggregator does not necessarily point
to a slave which is part of the aggregator. It points to the
slave structure containing the aggregator structure, while
completely different slaves (or no slaves at all) may be part of
the aggregator.

The agg_device_up() function wrongly uses agg->slave to find the state
of the aggregator.  Use agg->lag_ports->slave instead. The bug has
been introduced by commit 4cd6fe1c64
("bonding: fix link down handling in 802.3ad mode").

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-20 01:44:43 -07:00
Ben Hutchings 7c89943236 bonding, ipv4, ipv6, vlan: Handle NETDEV_BONDING_FAILOVER like NETDEV_NOTIFY_PEERS
It is undesirable for the bonding driver to be poking into higher
level protocols, and notifiers provide a way to avoid that.  This does
mean removing the ability to configure reptitition of gratuitous ARPs
and unsolicited NAs.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-17 23:36:03 -07:00
David S. Miller 7d038eb6dc bonding: Fix set-but-unused variable.
The variable 'vlan_dev' is set but unused in
bond_send_gratuitous_arp().  Just kill it off.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-17 00:50:58 -07:00
David Decotigny 5d30530efb net-bonding: Adding support for throughputs larger than 65536 Mbps
This updates the bonding driver to support v2.6.27-rc3 enhancements
(b11f8d8c aka. "ethtool: Expand ethtool_cmd.speed to 32 bits") which
allow to encode the Mbps link speed on 32-bits (Max 4 Pbps) instead of
16 (Max 65536 Mbps).

This patch also attempts to compact struct slave by reordering its
fields.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-14 22:00:32 -07:00
David Decotigny 65cce19c07 net-bonding: Fix minor/cosmetic type inconsistencies
The __get_link_speed() function returns a u16 value which was stored
in a u32 local variable. This patch uses the return value directly,
thus fixing that minor type consistency.

The 'duplex' field in struct slave being encoded on 8 bits, to be more
consistent we use a u8 integer (instead of u16) whenever we copy it to
local variables.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-14 22:00:32 -07:00
David Decotigny d30ee670f2 net-bonding: Fix minor sparse complaints
This gets rid of minor sparse complaints:
drivers/net/bonding/bond_main.c:4361:4: warning: do-while statement is not a compound statement
drivers/net/bonding/bond_main.c:243:12: warning: symbol 'bond_mode_name' was not declared. Should it be static?

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-14 22:00:31 -07:00
David S. Miller 1c01a80cfe Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/smsc911x.c
2011-04-11 13:44:25 -07:00
Peter Pan(潘卫平) 77c8e2c015 bonding:fix two typos
replace relpy with reply.
replace premanent with permanent.

Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11 13:15:56 -07:00
Peter Pan(潘卫平) 9814290ad0 net: fix tranmitted/tranmitting typo
replace tranmitted with transmitted.
replace tranmitting with transmitting.

Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11 13:15:56 -07:00
Peter Pan(潘卫平) 26f007b85a bonding:delete unused rlb_interval_counter
Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().

Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11 13:15:55 -07:00
Peter Pan(潘卫平) 3b64756845 bonding:delete unused alb_timer
Now bonding-alb uses delayed_work instead of timer_list.

Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11 13:15:55 -07:00
Peter Pan(潘卫平) 38dbaf0afb bonding:set save_load to 0 when initializing
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.

Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11 13:15:54 -07:00
Linus Torvalds 42933bac11 Merge branch 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
  Fix common misspellings
2011-04-07 11:14:49 -07:00
Tom Herbert c6e1a0d12c net: Allow no-cache copy from user on transmit
This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement.  skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg.  This functionality is
configurable per device using ethtool.

Presumably, this feature would only be useful when the driver does
not touch the data.  The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary.  For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.

This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply.  Platform is 16 core AMD x86.

No-cache copy disabled:
   672703 tps, 97.13% utilization
   50/90/99% latency:244.31 484.205 1028.41

No-cache copy enabled:
   702113 tps, 96.16% utilization,
   50/90/99% latency 238.56 467.56 956.955

Using 14000 byte request and response sizes demonstrate the
effects more dramatically:

No-cache copy disabled:
   79571 tps, 34.34 %utlization
   50/90/95% latency 1584.46 2319.59 5001.76

No-cache copy enabled:
   83856 tps, 34.81% utilization
   50/90/95% latency 2508.42 2622.62 2735.88

Note especially the effect on latency tail (95th percentile).

This seems to provide a nice performance improvement and is
consistent in the tests I ran.  Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-04 22:30:30 -07:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Peter Pan(潘卫平) 5e8996e728 bonding:typo in comment
use accumulates instead of acumulates.

Signed-off-by: Pan Weiping <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-31 01:54:22 -07:00
Jiri Pirko 35d48903e9 bonding: fix rx_handler locking
This prevents possible race between bond_enslave and bond_handle_frame
as reported by Nicolas by moving rx_handler register/unregister.
slave->bond is added to hold pointer to master bonding sructure. That
way dev->master is no longer used in bond_handler_frame.
Also, this removes "BUG: scheduling while atomic" message

Reported-by: Nicolas de Pesloüan <nicolas.2p.debian@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-23 12:45:10 -07:00
Nicolas de Pesloüan dadaa10b07 bonding: fix a typo in a comment
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-19 13:36:18 -07:00
Andy Gospodarek ceda86a108 bonding: enable netpoll without checking link status
Only slaves that are up should transmit netpoll frames, so there is no
need to check to see if a slave is up before enabling netpoll on it.
This resolves a reported failure on active-backup bonds where a slave
interface is down when netpoll was enabled.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:57:53 -07:00
Jiri Pirko 8a4eb5734e net: introduce rx_handler results and logic around that
This patch allows rx_handlers to better signalize what to do next to
it's caller. That makes skb->deliver_no_wcard no longer needed.

kernel-doc for rx_handler_result is taken from Nicolas' patch.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:53:54 -07:00
Jiri Pirko 2d7011ca79 bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
Since bond-related code was moved from net/core/dev.c into bonding,
IFF_SLAVE_INACTIVE is no longer needed. Replace is with flag "inactive"
stored in slave structure

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:51:20 -07:00
Jiri Pirko e30bc066ab bonding: wrap slave state work
transfers slave->state into slave->backup (that it's going to transfer
into bitfield. Introduce wrapper inlines to do the work with it.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:51:20 -07:00
Jiri Pirko 0bd80dad57 net: get rid of multiple bond-related netdevice->priv_flags
Now when bond-related code is moved from net/core/dev.c into bonding
code, multiple priv_flags are not needed anymore. So let them rot.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:51:19 -07:00
Jiri Pirko f1c1775ac7 bonding: register slave pointer for rx_handler
Register slave pointer as rx_handler data. That would eventually prevent
need to loop over slave devices to find the right slave.

Use synchronize_net to ensure that bond_handle_frame does not get slave
structure freed when working with that.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-16 12:51:19 -07:00
Phil Oester 5f86cad1e8 bonding: Improve syslog message at device creation time
When the bonding module is loaded, it creates bond0 by default.
Then, when attempting to create bond0, the following messages
are printed to syslog:

    kernel: bonding: bond0 is being created...
    kernel: bonding: Bond creation failed.

Which seems to indicate a problem, when in reality there is no
problem.  Since the actual error code is passed down from bond_create,
make use of it to print a bit less ominous message:

    kernel: bonding: bond0 is being created...
    kernel: bond0 already exists.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-15 19:29:39 -07:00
Phil Oester e826eafa65 bonding: Call netif_carrier_off after register_netdevice
Bringing up a bond interface with all network cables disconnected
does not properly set the interface as DOWN because the call to
netif_carrier_off occurs too early in bond_init.  The call needs
to occur after register_netdevice has set dev->reg_state to
NETREG_REGISTERED, so that netif_carrier_off will trigger the
call to linkwatch_fire_event.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-15 19:29:38 -07:00
Phil Oester fd0e435b0f bonding: Incorrect TX queue offset
When packets come in from a device with >= 16 receive queues
headed out a bonding interface, syslog gets filled with this:

    kernel: bond0 selects TX queue 16, but real number of TX queues is 16

because queue_mapping is offset by 1.  Adjust return value
to account for the offset.

This is a revision of my earlier patch (which did not use the
skb_rx_queue_* helpers - thanks to Ben for the suggestion).
Andy submitted a similar patch which emits a pr_warning on
invalid queue selection, but I believe the log spew is
not useful.  We can revisit that question in the future,
but in the interim I believe fixing the core problem is
worthwhile.

Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-15 19:29:37 -07:00
David S. Miller 78fbfd8a65 ipv4: Create and use route lookup helpers.
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-12 15:08:42 -08:00
David S. Miller 33175d84ee Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x/bnx2x_cmn.c
2011-03-10 14:26:00 -08:00
Amerigo Wang bd33acc3cc bonding: move procfs code into bond_procfs.c
V2: Move #ifdef CONFIG_PROC_FS into bonding.h, as suggested by David.

bond_main.c is bloating, separate the procfs code out,
move them to bond_procfs.c

Signed-off-by: WANG Cong <amwang@redhat.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-09 13:32:17 -08:00
Nils Carlson 9ac3524a94 bonding 802.3ad: Rename rx_machine_lock to state_machine_lock
Rename the rx_machine_lock to state_machine_lock as this makes more
sense in light of it now protecting all the state machines against
concurrency.

Signed-off-by: Nils Carlson <nils.carlson@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07 16:02:18 -08:00
Nils Carlson 16d79d7dc9 bonding 802.3ad: Fix the state machine locking v2
Changes since v1:
* Clarify an unclear comment
* Move a (possible) name change to a separate patch

The ad_rx_machine, ad_periodic_machine and ad_port_selection_logic
functions all inspect and alter common fields within the port structure.
Previous to this patch, only the ad_rx_machines were mutexed, and the
periodic and port_selection could run unmutexed against an ad_rx_machine
trigged by an arriving LACPDU.

This patch remedies the situation by protecting all the state machines
from concurrency. This is accomplished by locking around all the state
machines for a given port, which are executed at regular intervals; and
the ad_rx_machine when handling an incoming LACPDU.

Signed-off-by: Nils Carlson <nils.carlson@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07 16:02:17 -08:00
Changli Gao 541ac7c9b3 bonding: COW before overwriting the destination MAC address
When there is a ptype handler holding a clone of this skb, whose
destination MAC addresse is overwritten, the owner of this handler may
get a corrupted packet.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07 15:45:08 -08:00
Changli Gao cca134fe78 bonding: remove the unused dummy functions when net poll controller isn't enabled
These two functions are only used when net poll controller is enabled.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07 15:45:07 -08:00
David S. Miller b23dd4fe42 ipv4: Make output route lookup return rtable directly.
Instead of on the stack.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-02 14:31:35 -08:00
Amerigo Wang e364a3416d bonding: use the correct size for _simple_hash()
Clearly it should be the size of ->ip_dst here.
Although this is harmless, but it still reads odd.

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-28 13:21:28 -08:00
stephen hemminger 4ec952b8ab bonding: fix sparse warning
Fix use of zero where NULL expected. And wrap long line.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-28 12:39:58 -08:00
Jiri Pirko 5b2c4dd2ec net: convert bonding to use rx_handler
This patch converts bonding to use rx_handler. Results in cleaner
__netif_receive_skb() with much less exceptions needed. Also
bond-specific work is moved into bond code.

Did performance test using pktgen and counting incoming packets by
iptables. No regression noted.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-27 23:29:01 -08:00
Amerigo Wang 080e4130b1 netpoll: remove IFF_IN_NETPOLL flag
V4: rebase to net-next-2.6

This patch removes the flag IFF_IN_NETPOLL, we don't need it any more since
we have netpoll_tx_running() now.

Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-27 16:11:51 -08:00
Amerigo Wang 8a8efa22f5 bonding: sync netpoll code with bridge
V4: rebase to net-next-2.6
V3: remove an useless #ifdef.

This patch unifies the netpoll code in bonding with netpoll code in bridge,
thanks to Herbert that code is much cleaner now.

Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-27 16:11:50 -08:00
Jiri Pirko 9232ecca3e bond: implement [add/del]_slave ops
allow enslaving/releasing using netlink interface

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-13 16:58:40 -08:00
Jiri Pirko 1765a57533 net: make dev->master general
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.

 - netdev_set_master() - bond specifics moved to new function
   netdev_set_bond_master()
 - introduced netif_is_bond_slave() to check if device is a bonding slave

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-13 10:42:07 -08:00
Jiri Pirko 672bda3370 bonding: fix return value of couple of store functions
count is incorrectly returned even in case of fail. Return ret instead.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-25 13:13:16 -08:00
Michał Mirosław acd1130e87 net: reduce and unify printk level in netdev_fix_features()
Reduce printk() levels to KERN_INFO in netdev_fix_features() as this will
be used by ethtool and might spam dmesg unnecessarily.

This converts the function to use netdev_info() instead of plain printk().

As a side effect, bonding and bridge devices will now log dropped features
on every slave device change.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-24 15:45:15 -08:00
Michał Mirosław 04ed3e741d net: change netdev->features to u32
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.

Occurences found by `grep -r` on net/, drivers/net, include/

[ Move features and vlan_features next to each other in
  struct netdev, as per Eric Dumazet's suggestion -DaveM ]

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-24 15:32:47 -08:00
David S. Miller e92427b289 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 2011-01-24 13:17:06 -08:00
Neil Horman b30532515f bonding: Ensure that we unshare skbs prior to calling pskb_may_pull
Recently reported oops:

kernel BUG at net/core/skbuff.c:813!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/net/bond0/broadcast
CPU 8
Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding
ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2
ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas dm_mod [last unloaded: microcode]

Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding
ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2
ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas dm_mod [last unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.32-71.el6.x86_64 #1 BladeCenter HS22
-[7870AC1]-
RIP: 0010:[<ffffffff81405b16>]  [<ffffffff81405b16>]
pskb_expand_head+0x36/0x1e0
RSP: 0018:ffff880028303b70  EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff880c6458ec80 RCX: 0000000000000020
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880c6458ec80
RBP: ffff880028303bc0 R08: ffffffff818a6180 R09: ffff880c6458ed64
R10: ffff880c622b36c0 R11: 0000000000000400 R12: 0000000000000000
R13: 0000000000000180 R14: ffff880c622b3000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff880028300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000038653452a4 CR3: 0000000001001000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff8806649c2000, task ffff880c64f16ab0)
Stack:
 ffff880028303bc0 ffffffff8104fff9 000000000000001c 0000000100000000
<0> ffff880000047d80 ffff880c6458ec80 000000000000001c ffff880c6223da00
<0> ffff880c622b3000 0000000000000000 ffff880028303c10 ffffffff81407f7a
Call Trace:
<IRQ>
 [<ffffffff8104fff9>] ? __wake_up_common+0x59/0x90
 [<ffffffff81407f7a>] __pskb_pull_tail+0x2aa/0x360
 [<ffffffffa0244530>] bond_arp_rcv+0x2c0/0x2e0 [bonding]
 [<ffffffff814a0857>] ? packet_rcv+0x377/0x440
 [<ffffffff8140f21b>] netif_receive_skb+0x2db/0x670
 [<ffffffff8140f788>] napi_skb_finish+0x58/0x70
 [<ffffffff8140fc89>] napi_gro_receive+0x39/0x50
 [<ffffffffa01286eb>] ixgbe_clean_rx_irq+0x35b/0x900 [ixgbe]
 [<ffffffffa01290f6>] ixgbe_clean_rxtx_many+0x136/0x240 [ixgbe]
 [<ffffffff8140fe53>] net_rx_action+0x103/0x210
 [<ffffffff81073bd7>] __do_softirq+0xb7/0x1e0
 [<ffffffff810d8740>] ? handle_IRQ_event+0x60/0x170
 [<ffffffff810142cc>] call_softirq+0x1c/0x30
 [<ffffffff81015f35>] do_softirq+0x65/0xa0
 [<ffffffff810739d5>] irq_exit+0x85/0x90
 [<ffffffff814cf915>] do_IRQ+0x75/0xf0
 [<ffffffff81013ad3>] ret_from_intr+0x0/0x11
 <EOI>
 [<ffffffff8101bc01>] ? mwait_idle+0x71/0xd0
 [<ffffffff814cd80a>] ? atomic_notifier_call_chain+0x1a/0x20
 [<ffffffff81011e96>] cpu_idle+0xb6/0x110
 [<ffffffff814c17c8>] start_secondary+0x1fc/0x23f

Resulted from bonding driver registering packet handlers via dev_add_pack and
then trying to call pskb_may_pull. If another packet handler (like for AF_PACKET
sockets) gets called first, the delivered skb will have a user count > 1, which
causes pskb_may_pull to BUG halt when it does its skb_shared check.  Fix this by
calling skb_share_check prior to the may_pull call sites in the bonding driver
to clone the skb when needed.  Tested by myself and the reported successfully.

Signed-off-by: Neil Horman
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-20 16:45:56 -08:00
Linus Torvalds 008d23e485 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  Documentation/trace/events.txt: Remove obsolete sched_signal_send.
  writeback: fix global_dirty_limits comment runtime -> real-time
  ppc: fix comment typo singal -> signal
  drivers: fix comment typo diable -> disable.
  m68k: fix comment typo diable -> disable.
  wireless: comment typo fix diable -> disable.
  media: comment typo fix diable -> disable.
  remove doc for obsolete dynamic-printk kernel-parameter
  remove extraneous 'is' from Documentation/iostats.txt
  Fix spelling milisec -> ms in snd_ps3 module parameter description
  Fix spelling mistakes in comments
  Revert conflicting V4L changes
  i7core_edac: fix typos in comments
  mm/rmap.c: fix comment
  sound, ca0106: Fix assignment to 'channel'.
  hrtimer: fix a typo in comment
  init/Kconfig: fix typo
  anon_inodes: fix wrong function name in comment
  fix comment typos concerning "consistent"
  poll: fix a typo in comment
  ...

Fix up trivial conflicts in:
 - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
 - fs/ext4/ext4.h

Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-13 10:05:56 -08:00
Alexey Dobriyan 57cc7215b7 headers: kobject.h redux
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-10 08:51:44 -08:00
Jiri Kosina 4b7bd36470 Merge branch 'master' into for-next
Conflicts:
	MAINTAINERS
	arch/arm/mach-omap2/pm24xx.c
	drivers/scsi/bfa/bfa_fcpim.c

Needed to update to apply fixes for which the old branch was too
outdated.
2010-12-22 18:57:02 +01:00
David S. Miller b4aa9e05a6 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x/bnx2x.h
	drivers/net/wireless/iwlwifi/iwl-1000.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-core.h
	drivers/vhost/vhost.c
2010-12-17 12:27:22 -08:00
Taku Izumi caafa84251 bonding: add the debugfs interface to see RLB hash table
This patch provices the debugfs interface to see RLB hash table
like the following:

# cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
SourceIP        DestinationIP   Destination MAC   DEV
10.124.196.205  10.124.196.205  ff:ff:ff:ff:ff:ff eth4
10.124.196.205  10.124.196.81   00:19:99:XX:XX:XX eth3
10.124.196.205  10.124.196.1    00:21:d8:XX:XX:XX eth0

This is helpful to check if the receive load balancing works as expected.

Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 13:16:05 -08:00
Taku Izumi 411204a5a1 bonding: migrate some macros from bond_alb.c to bond_alb.h
This patch simply migrates some macros from bond_alb.c to bond_alb.h.

Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 13:16:05 -08:00
Ben Hutchings f88a4a9b65 bonding/vlan: Fix mangled NAs on slaves without VLAN tag insertion
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats.  If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).

Fix this by adding the tag out-of-line and relying on
dev_hard_start_xmit() to insert it inline if necessary.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 12:43:22 -08:00
Ben Hutchings ffa95ed50f bonding: Change active slave quietly when bond is down
bond_change_active_slave() may be called when a slave is added, even
if the bond has not been brought up yet.  It may then attempt to send
packets, and further it may use mcast_work which is uninitialised
before the bond is brought up.  Add the necessary checks for
netif_running(bond->dev).

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 12:43:22 -08:00
Ben Hutchings 8387451e55 bonding/vlan: Remove redundant VLAN tag insertion logic
A bond may have a mixture of slave devices with and without hardware
VLAN tag insertion capability.  Therefore it always claims this
capability and performs software VLAN tag insertion if the slave does
not.

Since commit 7b9c609037, this has
also been done by dev_hard_start_xmit().  The result is that VLAN-
tagged skbs are now double-tagged when transmitted through slave
devices without hardware VLAN tag insertion!

Remove the now-redundant logic from bond_dev_queue_xmit().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 12:43:21 -08:00
Hillf Danton af3e5bd5f6 bonding: Fix slave selection bug.
The returned slave is incorrect, if the net device under check is not
charged yet by the master.

Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 12:24:02 -08:00
Taku Izumi f073c7ca29 bonding: add the debugfs facility to the bonding driver
This patch provides the debugfs facility to the bonding driver.
The "bonding" directory is created in the debugfs root and directories of
each bonding interface (like bond0, bond1...) are created in that.

 # mount -t debugfs none /sys/kernel/debug

 # ls /sys/kernel/debug/bonding
 bond0  bond1

Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10 16:24:33 -08:00
Neil Horman fb4fa76a1f net: Convert netpoll blocking api in bonding driver to be a counter
A while back I made some changes to enable netpoll in the bonding driver.  Among
them was a per-cpu flag that indicated we were in a path that held locks which
could cause the netpoll path to block in during tx, and as such the tx path
should queue the frame for later use.  This appears to have given rise to a
regression.  If one of those paths on which we hold the per-cpu flag yields the
cpu, its possible for us to come back on a different cpu, leading to us clearing
a different flag than we set.  This results in odd netpoll drops, and BUG
backtraces appearing in the log, as we check to make sure that we only clear set
bits, and only set clear bits.  I had though briefly about changing the
offending paths so that they wouldn't sleep, but looking at my origional work
more closely, it doesn't appear that a per-cpu flag is warranted.  We alrady
gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the
normal tx case anyway.  And practically speaking, the normal use case for
netpoll is to only have one client anyway, so we're not going to erroneously
queue netpoll frames when its actually safe to do so.  As such, lets just
convert that per-cpu flag to an atomic counter.  It fixes the rescheduling bugs,
is equivalent from a performance perspective and actually eliminates some code
in the process.

Tested by the reporter and myself, successfully

Reported-by: Liang Zheng <lzheng@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-09 20:33:46 -08:00
David S. Miller fe6c791570 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
	net/llc/af_llc.c
2010-12-08 13:47:38 -08:00
David Strand d13a2cb63d bonding: check for assigned mac before adopting the slaves mac address
Restore the check for an unassigned mac address before adopting the
first slaves as it's own. The change in behavior was introduced by:

commit c20811a79e
Author: Jiri Pirko <jpirko@redhat.com>

    bonding: move dev_addr cpy to bond_enslave


Signed-off-by: David Strand <dpstrand@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-01 11:43:08 -08:00
David S. Miller 24912420e9 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	net/core/net-sysfs.c
	net/ipv6/addrconf.c
2010-11-19 13:13:47 -08:00
Eric Dumazet 866f3b25a2 bonding: IGMP handling cleanup
Instead of iterating in_dev->mc_list from bonding driver, its better
to call a helper function provided by igmp.c
Details of implementation (locking) are private to igmp code.

ip_mc_rejoin_group(struct ip_mc_list *im) becomes
ip_mc_rejoin_groups(struct in_device *in_dev);

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 09:33:19 -08:00
Eric Dumazet 3006bc3889 bonding: fix a race in IGMP handling
RCU conversion in IGMP code done in net-next-2.6 raised a race in
__bond_resend_igmp_join_requests().

It iterates in_dev->mc_list without appropriate protection (RTNL, or
read_lock on in_dev->mc_list_lock).

Another cpu might delete an entry while we use it and trigger a fault.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 09:30:42 -08:00
Joe Perches c04914af68 drivers/net/bonding: Remove unnecessary casts of netdev_priv
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-17 10:36:50 -08:00
Eric Dumazet e4a7b93bd5 bonding: remove dev_base_lock use
bond_info_seq_start() uses a read_lock(&dev_base_lock) to make sure
device doesn’t disappear. Same goal can be achieved using RCU.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-08 13:50:07 -08:00
Uwe Kleine-König b595076a18 tree-wide: fix comment/printk typos
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-01 15:38:34 -04:00
Jarek Poplawski a71fb88145 bonding: Fix lockdep warning after bond_vlan_rx_register()
Fix lockdep warning:
[   52.991402] ======================================================
[   52.991511] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
[   52.991569] 2.6.36-04573-g4b60626-dirty #65
[   52.991622] ------------------------------------------------------
[   52.991696] ip/4842 [HC0[0]:SC0[4]:HE1:SE0] is trying to acquire:
[   52.991758]  (&bond->lock){++++..}, at: [<efe4d300>] bond_set_multicast_list+0x60/0x2c0 [bonding]
[   52.991966]
[   52.991967] and this task is already holding:
[   52.992008]  (&bonding_netdev_addr_lock_key){+.....}, at: [<c04e5530>] dev_mc_sync+0x50/0xa0
[   52.992008] which would create a new lock dependency:
[   52.992008]  (&bonding_netdev_addr_lock_key){+.....} -> (&bond->lock){++++..}
[   52.992008]
[   52.992008] but this new dependency connects a SOFTIRQ-irq-safe lock:
[   52.992008]  (&(&mc->mca_lock)->rlock){+.-...}
[   52.992008] ... which became SOFTIRQ-irq-safe at:
[   52.992008]   [<c0272beb>] __lock_acquire+0x96b/0x1960
[   52.992008]   [<c027415e>] lock_acquire+0x7e/0xf0
[   52.992008]   [<c05f356d>] _raw_spin_lock_bh+0x3d/0x50
[   52.992008]   [<c0584e40>] mld_ifc_timer_expire+0xf0/0x280
[   52.992008]   [<c024cee6>] run_timer_softirq+0x146/0x310
[   52.992008]   [<c024591d>] __do_softirq+0xad/0x1c0
[   52.992008]
[   52.992008] to a SOFTIRQ-irq-unsafe lock:
[   52.992008]  (&bond->lock){++++..}
[   52.992008] ... which became SOFTIRQ-irq-unsafe at:
[   52.992008] ...  [<c0272c3b>] __lock_acquire+0x9bb/0x1960
[   52.992008]   [<c027415e>] lock_acquire+0x7e/0xf0
[   52.992008]   [<c05f36b8>] _raw_write_lock+0x38/0x50
[   52.992008]   [<efe4cbe4>] bond_vlan_rx_register+0x24/0x70 [bonding]
[   52.992008]   [<c0598010>] register_vlan_dev+0xc0/0x280
[   52.992008]   [<c0599f3a>] vlan_newlink+0xaa/0xd0
[   52.992008]   [<c04ed4b4>] rtnl_newlink+0x404/0x490
[   52.992008]   [<c04ece35>] rtnetlink_rcv_msg+0x1e5/0x220
[   52.992008]   [<c050424e>] netlink_rcv_skb+0x8e/0xb0
[   52.992008]   [<c04ecbac>] rtnetlink_rcv+0x1c/0x30
[   52.992008]   [<c0503bfb>] netlink_unicast+0x24b/0x290
[   52.992008]   [<c0503e37>] netlink_sendmsg+0x1f7/0x310
[   52.992008]   [<c04cd41c>] sock_sendmsg+0xac/0xe0
[   52.992008]   [<c04ceb80>] sys_sendmsg+0x130/0x230
[   52.992008]   [<c04cf04e>] sys_socketcall+0xde/0x280
[   52.992008]   [<c0202d10>] sysenter_do_call+0x12/0x36
[   52.992008]
[   52.992008] other info that might help us debug this:
...
[ Full info at netdev: Wed, 27 Oct 2010 12:24:30 +0200
  Subject: [BUG net-2.6 vlan/bonding] lockdep splats ]

Use BH variant of write_lock(&bond->lock) (as elsewhere in bond_main)
to prevent this dependency.

Fixes commit f35188faa0 [v2.6.36]

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
2010-10-27 14:24:07 -07:00
Bandan Das 7bfc475323 bonding: cleanup: remove braces from single block statements
checkpatch.pl cleanup : Remove braces from single statement
blocks.

Signed-off-by: Bandan Das <bandan.das@stratus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 03:09:49 -07:00
Bandan Das 128ea6c3ee bonding: cleanup : add space around operators
checkpatch.pl cleanup: Added spaces around operators at various places.
Also fixed some c99 style comments that I came across.

Signed-off-by: Bandan Das <bandan.das@stratus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 03:09:49 -07:00
stephen hemminger 26d8ee75e0 bonding: make release_and_destroy static
Only used in main file.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 03:09:46 -07:00
stephen hemminger 379b738341 bonding: make bond_resend_igmp_join_requests_delayed static
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 03:09:43 -07:00
Neil Horman 9ff76c951c netpoll: Remove netpoll blocking from uninit path
Some recent testing in netpoll with bonding showed this backtrace

 ------------[ cut here ]------------
 kernel BUG at drivers/net/bonding/bonding.h:134!
 invalid opcode: 0000 [#1] SMP
 last sysfs file: /sys/devices/pci0000:00/0000:00:1d.2/usb7/devnum
 CPU 0
 Pid: 1876, comm: rmmod Not tainted 2.6.36-rc3+ #10 D26928/
 RIP: 0010:[<ffffffffa0514ba4>]  [<ffffffffa0514ba4>] bond_uninit+0x6f4/0x7a0
 RSP: 0018:ffff88003b1b5d58  EFLAGS: 00010296
 RAX: ffff88003b9b6200 RBX: ffff8800373e8e00 RCX: 00000000000f4240
 RDX: 00000000ffffffff RSI: 0000000000000286 RDI: 0000000000000286
 RBP: ffff88003b1b5dc8 R08: 0000000000000000 R09: 00000001af7de920
 R10: 0000000000000000 R11: ffff880002495e98 R12: ffff880037922700
 R13: ffff880038c31000 R14: ffff880037922730 R15: 0000000000000286
 FS:  00007f90e6d72700(0000) GS:ffff880002400000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 000000346f0d9ad0 CR3: 000000003b263000 CR4: 00000000000006f0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 Process rmmod (pid: 1876, threadinfo ffff88003b1b4000, task ffff88003b36aa80)
 Stack:
 00000000ffffffff ffff88003b1b5d7a ffff8800379221e8 ffff880037922000
 <0> ffff88003b1b5dc8 ffffffff813eb5fb ffff88003b1b5da8 0000000031b177a3
 <0> ffff88003b1b5da8 ffff880037922000 ffff88003b1b5e48 ffff88003b1b5e48
 Call Trace:
 [<ffffffff813eb5fb>] ? rtmsg_ifinfo+0xcb/0xf0
 [<ffffffff813daad8>] rollback_registered_many+0x168/0x280
 [<ffffffff813dac09>] unregister_netdevice_many+0x19/0x80
 [<ffffffff813e97b3>] __rtnl_kill_links+0x63/0x90
 [<ffffffff813e980b>] __rtnl_link_unregister+0x2b/0x60
 [<ffffffff813e9bde>] rtnl_link_unregister+0x1e/0x30
 [<ffffffffa052124b>] bonding_exit+0x37/0x51 [bonding]
 [<ffffffff81098b2e>] sys_delete_module+0x19e/0x270
 [<ffffffff810bb2b2>] ? audit_syscall_entry+0x252/0x280
 [<ffffffff8100b0b2>] system_call_fastpath+0x16/0x1b
 RIP  [<ffffffffa0514ba4>] bond_uninit+0x6f4/0x7a0 [bonding]
 RSP <ffff88003b1b5d58>
 ---[ end trace 1395ad691cea24d1 ]---

It occurs because of my recent netpoll blocking patches, which I added to avoid
recursive deadlock in the bonding driver.  It relies on some per cpu bits, but
the shutdown path forces some rescheduling as we cancel workqueues for the
driver and wait for some device refcounts.  If after the forced reschedule, we
wind up on a different cpu we trigger the bughalt in unblock_netpoll_tx.

The fix is to remove the netpoll block/unblock calls from bond_release_all.
This is safe to do because bond_uninit, which is called via ndo_uninit in
rollback_registered_many, doesn't occur until we send a NETDEV_UNREGISTER event,
which triggers netconsole to remove us as a netpoll client, so we are guaranteed
not to recurse into our own tx path here.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 01:44:29 -07:00
Neil Horman 45b0cb8abd bonding: Re-enable netpoll over bonding
With the inclusion of previous fixup patches, netpoll over bonding apears to
work reliably with failover conditions.  This reverts Gospos previous commit
c22d7ac844, and allows access again to the netpoll
functionality in the bonding driver.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 08:32:09 -07:00
Neil Horman e843fa5088 bonding: Fix deadlock in bonding driver resulting from internal locking when using netpoll
The monitoring paths in the bonding driver take write locks that are shared by
the tx path.  If netconsole is in use, these paths can call printk which puts us
in the netpoll tx path, which, if netconsole is attached to the bonding driver,
result in deadlock (the xmit_lock guards are useless in netpoll_send_skb, as the
monitor paths in the bonding driver don't claim the xmit_lock, nor should they).
The solution is to use a per cpu flag internal to the driver to indicate when a
cpu is holding the lock in a path that might recusrse into the tx path for the
driver via netconsole.  By checking this flag on transmit, we can defer the
sending of the netconsole frames until a later time using the retransmit feature
of netpoll_send_skb that is triggered on the return code NETDEV_TX_BUSY.  I've
tested this and am able to transmit via netconsole while causing failover
conditions on the bond slave links.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 08:32:07 -07:00
Neil Horman c2355e1ab9 bonding: Fix bonding drivers improper modification of netpoll structure
The bonding driver currently modifies the netpoll structure in its xmit path
while sending frames from netpoll.  This is racy, as other cpus can access the
netpoll structure in parallel. Since the bonding driver points np->dev to a
slave device, other cpus can inadvertently attempt to send data directly to
slave devices, leading to improper locking with the bonding master, lost frames,
and deadlocks.  This patch fixes that up.

This patch also removes the real_dev pointer from the netpoll structure as that
data is really only used by bonding in the poll_controller, and we can emulate
its behavior by check each slave for IS_UP.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 08:32:07 -07:00
David S. Miller 69259abb64 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/pcmcia/pcnet_cs.c
	net/caif/caif_socket.c
2010-10-06 19:39:31 -07:00
Krzysztof Oledzki dd53df265b bonding: add Speed/Duplex information to /proc/net/bonding/bond
Effect:
 Slave Interface: eth5
 MII Status: up
 Speed: 10000 Mbps
 Duplex: full
 Link Failure Count: 0
 Permanent HW addr: XX:XX:XX:XX:XX:XX
 Slave queue ID: 0

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 18:43:34 -07:00
Krzysztof Piotr Oledzki 546add7946 bonding: reread information about speed and duplex when interface goes up
When an interface was enslaved when it was down, bonding thinks
it has speed -1 even after it goes up. This leads into selecting
a wrong active interface in active/backup mode on mixed 10G/1G or
1G/100M environment.

before:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.

after:
 bonding: bond0: link status definitely up for interface eth5, 10000 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex.

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 14:28:22 -07:00
Krzysztof Piotr Oledzki 700c2a779e bonding: print information about speed and duplex seen by the driver
before:
 bonding: bond0: link status definitely up for interface eth5
 bonding: bond0: link status definitely up for interface eth0

after:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.


Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 14:25:06 -07:00
Flavio Leitner c2952c314b bonding: add retransmit membership reports tunable
Allow sysadmins to configure the number of multicast
membership report sent on a link failure event.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:26:58 -07:00
Flavio Leitner 5a37e8ca85 bonding: rejoin multicast groups on VLANs
During a failover, the IGMP membership is sent to update
the switch restoring the traffic, but it misses groups added
to VLAN devices running on top of bonding devices.

This patch changes it to iterate over all VLAN devices
on top of it sending IGMP memberships too.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:26:56 -07:00
Neil Horman 27e6f065df bonding: fix WARN_ON when writing to bond_master sysfs file
Fix a WARN_ON failure in bond_masters sysfs file

Got a report of this warning recently

bonding: bond0 is being created...
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:590 proc_register+0x14d/0x185()
Hardware name: ProLiant BL465c G1
proc_dir_entry 'bonding/bond0' already registered
Modules linked in: bonding ipv6 tg3 bnx2 shpchp amd64_edac_mod edac_core
ipmi_si
ipmi_msghandler serio_raw i2c_piix4 k8temp edac_mce_amd hpwdt microcode hpsa
cc
iss radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded:
scsi_wai
t_scan]
Pid: 935, comm: ifup-eth Not tainted 2.6.33.5-124.fc13.x86_64 #1
Call Trace:
[<ffffffff8104b54c>] warn_slowpath_common+0x77/0x8f
[<ffffffff8104b5b1>] warn_slowpath_fmt+0x3c/0x3e
[<ffffffff8114bf0b>] proc_register+0x14d/0x185
[<ffffffff8114c20c>] proc_create_data+0x87/0xa1
[<ffffffffa0211e9b>] bond_create_proc_entry+0x55/0x95 [bonding]
[<ffffffffa0215e5d>] bond_init+0x95/0xd0 [bonding]
[<ffffffff8138cd97>] register_netdevice+0xdd/0x29e
[<ffffffffa021240b>] bond_create+0x8e/0xb8 [bonding]
[<ffffffffa021c4be>] bonding_store_bonds+0xb3/0x1c1 [bonding]
[<ffffffff812aec85>] class_attr_store+0x27/0x29
[<ffffffff8115423d>] sysfs_write_file+0x10f/0x14b
[<ffffffff81101acf>] vfs_write+0xa9/0x106
[<ffffffff81101be2>] sys_write+0x45/0x69
[<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
---[ end trace a677c3f7f8b16b1e ]---
bonding: Bond creation failed.

It happens because a user space writer to bond_master can try to
register an already existing bond interface name.  Fix it by teaching
bond_create to check for the existance of devices with that name first
in cases where a non-NULL name parameter has been passed in

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:06:01 -07:00
David S. Miller e40051d134 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/qlcnic/qlcnic_init.c
	net/ipv4/ip_output.c
2010-09-27 01:03:03 -07:00
Eric Dumazet 807540baae drivers/net: return operator cleanup
Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26 18:34:29 -07:00
Eric Dumazet e6599c2ecf bonding: enable gro by default
gro can be enabled by default on bonding devices.

Actual support depends on the lower devices.

One can still use ethtool to switch off GRO if needed.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17 16:53:24 -07:00
Andy Gospodarek ab12811c89 bonding: correctly process non-linear skbs
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there.  That explained the inability to form an
802.3ad-based bond.  For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.

This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.

Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-14 14:25:32 -07:00
Jiri Bohac cb32f2a0d1 bonding: Fix jiffies overflow problems (again)
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).

Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.

jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-07 13:57:20 -07:00
Andy Gospodarek c5cb002fb0 bonding: prevent sysfs from allowing arp monitoring with alb/tlb
When using module options arp monitoring and balance-alb/balance-tlb
are mutually exclusive options.  Anytime balance-alb/balance-tlb are
enabled mii monitoring is forced to 100ms if not set.  When configuring
via sysfs no checking is currently done.

Handling these cases with sysfs has to be done a bit differently because
we do not have all configuration information available at once.  This
patch will not allow a mode change to balance-alb/balance-tlb if
arp_interval is already non-zero.  It will also not allow the user to
set a non-zero arp_interval value if the mode is already set to
balance-alb/balance-tlb.  They are still mutually exclusive on a
first-come, first serve basis.

Tested with initscripts on Fedora and manual setting via sysfs.

Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-30 23:27:57 -07:00
David S. Miller bb7e95c8fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x_main.c

Merge bnx2x bug fixes in by hand... :-/

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-27 21:01:35 -07:00
Greg Edwards d8190dff01 bonding: set device in RLB ARP packet handler
After:

commit 6146b1a4da
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Tue Nov 4 17:51:15 2008 -0800

    bonding: Fix ALB mode to balance traffic on VLANs

the dev field in the RLB ARP packet handler was set to NULL to wildcard
and accommodate balancing VLANs on top of bonds.

This has the side-effect of the packet handler being called against
other, non RLB-enabled bonds, and a kernel oops results when it tries to
dereference rx_hashtbl in rlb_update_entry_from_arp(), which won't be
set for those bonds, e.g. active-backup.

With the __netif_receive_skb() changes from:

commit 1f3c8804ac
Author: Andy Gospodarek <andy@greyhouse.net>
Date:   Mon Dec 14 10:48:58 2009 +0000

    bonding: allow arp_ip_targets on separate vlans to use arp validation

frames received on VLANs correctly make their way to the bond's handler,
so we no longer need to wildcard the device.

The oops can be reproduced by:

modprobe bonding

echo active-backup > /sys/class/net/bond0/bonding/mode
echo 100 > /sys/class/net/bond0/bonding/miimon
ifconfig bond0 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth0 > /sys/class/net/bond0/bonding/slaves
echo +eth1 > /sys/class/net/bond0/bonding/slaves

echo +bond1 > /sys/class/net/bonding_masters
echo balance-alb > /sys/class/net/bond1/bonding/mode
echo 100 > /sys/class/net/bond1/bonding/miimon
ifconfig bond1 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth2 > /sys/class/net/bond1/bonding/slaves
echo +eth3 > /sys/class/net/bond1/bonding/slaves

Pass some traffic on bond0.  Boom.

[ Tested, behaves as advertised.  I do not believe a test of the bonding
mode is necessary, as there is no race between the packet handler and
the bonding mode changing (the mode can only change when the device is
closed).  Also updated the log message to include the reproduction and
full commit ids.  -J ]

Signed-off-by: Greg Edwards <greg.edwards@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-24 20:37:48 -07:00
Jay Vosburgh 03dc2f4c52 bonding: don't lock when copying/clearing VLAN list on slave
When copying VLAN information to or removing from a slave
during slave addition or removal, the bonding code currently holds
the bond->lock for write to prevent concurrent modification of the
vlan_list / vlgrp.

	This is unnecessary, as all of these operations occur under
RTNL.  Holding the bond->lock also caused might_sleep issues for
some drivers' ndo_vlan_* functions.  This patch removes the extra
locking.

	Problem reported by Michael Chan <mchan@broadcom.com>

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-22 14:14:47 -07:00
Jay Vosburgh f35188faa0 bonding: change test for presence of VLANs
After commit ad1afb0039
("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
it is now regular practice for a VLAN "add vid" for VLAN 0 to
arrive prior to any VLAN registration or creation of a vlan_group.

	This patch updates the bonding code that tests for the presence
of VLANs configured above bonding.  The new logic tests for bond->vlgrp
to determine if a registration has occured, instead of testing that
bonding's internal vlan_list is empty.

	The old code would panic when vlan_list was not empty, but
vlgrp was still NULL (because only an "add vid" for VLAN 0 had occured).

	Bonding still adds VLAN 0 to its internal list so that 802.1p
frames are handled correctly on transmit when non-VLAN accelerated
slaves are members of the bond.  The test against bond->vlan_list
remains in bond_dev_queue_xmit for this reason.

	Modification to the bond->vlgrp now occurs under lock (in
addition to RTNL), because not all inspections of it occur under RTNL.

	Additionally, because 8021q will never issue a "kill vid" for
VLAN 0, there is now logic in bond_uninit to release any remaining
entries from vlan_list.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Pedro Garcia <pedro.netdev@dondevamos.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-22 14:14:46 -07:00
Eric Dumazet 90e1795b9b bonding: avoid a warning
drivers/net/bonding/bond_main.c:179:12: warning: ‘disable_netpoll’
defined but not used

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-19 13:34:16 -07:00
Eric Dumazet db5dda9057 bonding: fix bond_inet6addr_event()
After commit ad1afb0039 (vlan_dev: VLAN 0 should be treated
as "no vlan tag" (802.1p packet)),
bond_inet6addr_event() might be called with a NULL bond->vlgrp pointer, and
a non empty bond->vlan_list. vlan_group_get_device() is dereferencing a NULL pointer.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-19 09:34:31 -07:00
Nicolas de Pesloüan 79236680bd bonding: fix a buffer overflow in bonding_show_queue_id.
The test for buffer overflow ensures we have room for 6 more bytes.
sprintf, called with %s:%d, slave->dev->name, slave->queue_id may yield
far more than 6 bytes.

The correct test is res > (PAGE_SIZE - IFNAMSIZ - 6) .

Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14 18:24:54 -07:00
David S. Miller 597e608a84 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-07-07 15:59:38 -07:00
Eric Dumazet 28172739f0 net: fix 64 bit counters on 32 bit arches
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.

One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().

Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)

Old drivers (only providing get_stats() method) need no changes.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07 14:58:56 -07:00
Flavio Leitner 42d782ac1b bonding: check if clients MAC addr has changed
When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.

What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.

See more information including the relevant functions below:

   System 1                          System 2
    bond0                             bond0

   ping <system2>
    ARP request  --------->
                           <--------- ARP reply

+->rlb_arp_recv  <---------------------+   <--- loop begins
|  rlb_update_entry_from_arp           |
|  client_info->ntt = 1;               |
|  bond_info->rx_ntt = 1;              |
|                                      |
|         <communication succeed>      |
|                                      |
|  bond_alb_monitor                    |
|  rlb_update_rx_clients               |
|  rlb_update_client                   |
|  arp_create(ARPOP_REPLY)             |
|   send ARP reply -------------->     V
|   send ARP reply -------------->
|                               rlb_arp_recv
|                               rlb_update_entry_from_arp
|                               client_info->ntt = 1;
|                               bond_info->rx_ntt = 1;
|                           < snipped, same as in system 1>
+-------           <-------------- send ARP reply
                   <-------------- send ARP reply

Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.

This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30 13:51:11 -07:00
Andy Gospodarek c22d7ac844 bonding: prevent netpoll over bonded interfaces
Support for netpoll over bonded interfaces was added here:

	commit f6dc31a85c
	Author: WANG Cong <amwang@redhat.com>
	Date:   Thu May 6 00:48:51 2010 -0700

	    bonding: make bonding support netpoll

but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU.  Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.

Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-28 23:54:10 -07:00
Ben Hutchings be1f3c2c02 net: Enable 64-bit net device statistics on 32-bit architectures
Use struct rtnl_link_stats64 as the statistics structure.

On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64.  Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.

Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64.  Drivers that implement
this operation must not update the structure asynchronously.

Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64.  Change callers of
dev_get_stats() accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-12 15:51:22 -07:00
Changli Gao d8d1f30b95 net-next: remove useless union keyword
remove useless union keyword in rtable, rt6_info and dn_route.

Since there is only one member in a union, the union keyword isn't useful.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-10 23:31:35 -07:00
Andy Gospodarek bb1d912323 bonding: allow user-controlled output slave selection
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.

This patch give the user the ability to control the output slave for
round-robin and active-backup bonding.  Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode.  Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.

Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag.  This will allow reception of unicast traffic on
any of the backup interfaces.

This was tested with IPv4-based filters as well as VLAN-based filters
with good results.

More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-05 02:23:17 -07:00
Andy Gospodarek ebd8e4977a bonding: add all_slaves_active parameter
v2: changed parameter name from 'keep_all' to 'all_slaves_active' and
skipped setting slaves to inactive rather than creating a new flag at
Jay's suggestion.

In an effort to suppress duplicate frames on certain bonding modes
(specifically the modes that do not require additional configuration on
the switch or switches connected to the host), code was added in the
generic receive patch in 2.6.16.  The current behavior works quite well
for most users, but there are some times it would be nice to restore old
functionality and allow all frames to make their way up the stack.

This patch adds support for a new module option and sysfs file called
'all_slaves_active' that will restore pre-2.6.16 functionality if the
user desires.  The default value is '0' and retains existing behavior,
but the user can set it to '1' and allow all frames up if desired.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-05 02:23:17 -07:00
Jiri Pirko 097811bb48 bonding: optimize tlb_get_least_loaded_slave
In the worst case, when the first loop breaks an the end of the slave list,
the slave list is iterated through twice. This patch reduces this
function only to one loop. Also makes it simpler.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:24 -07:00
Jiri Pirko 5206e24c2c bonding: remove unused original_flags struct slave member
This is stored but never restored. So remove this as it is useless.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:24 -07:00
Jiri Pirko c20811a79e bonding: move dev_addr cpy to bond_enslave
Move the code that copies slave's mac address in case that's the first slave into
bond_enslave. Ifenslave app does this also but that's not a problem. This is
something that should be done in bond_enslave, and it shound not matter from
where is it called.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:23 -07:00
Jiri Pirko f9f3545e1e bonding: make bonding_store_slaves simpler
This patch makes bonding_store_slaves function nicer and easier to understand.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:42 -07:00
Jiri Pirko 3dd90905e0 bonding: remove redundant checks from bonding_store_slaves V2
(it's actually the same as v1)

Remove checks that duplicates similar checks in bond_enslave.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:42 -07:00
Jiri Pirko b15ba0fbdc bonding: move slave MTU handling from sysfs V2
V1->V2: corrected res/ret use

For some reason, MTU handling (storing, and restoring) is taking  place in
bond_sysfs. The correct place for this code is in bond_enslave, bond_release.
So move it there.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:41 -07:00
Jiri Pirko 6458590999 bonding: remove unused variable "found"
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:40 -07:00
WANG Cong f6dc31a85c bonding: make bonding support netpoll
Based on Andy's work, but I modified a lot.

Similar to the patch for bridge, this patch does:

1) implement the 2 methods to support netpoll for bonding;

2) modify netpoll during forwarding packets via bonding;

3) disable netpoll support of bonding when a netpoll-unabled device
   is added to bonding;

4) enable netpoll support when all underlying devices support netpoll.

Cc: Andy Gospodarek <gospo@redhat.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 00:48:51 -07:00
David S. Miller 4a35ecf8bf Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	drivers/net/via-velocity.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
2010-04-06 23:53:30 -07:00
Jiri Pirko 22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Jiri Pirko a748ee2426 net: move address list functions to a separate file
+little renaming of unicast functions to be smooth with multicast ones

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:11 -07:00
Amerigo Wang 9e2e61fbf8 bonding: fix potential deadlock in bond_uninit()
bond_uninit() is invoked with rtnl_lock held, when it does destroy_workqueue()
which will potentially flush all works in this workqueue, if we hold rtnl_lock
again in the work function, it will deadlock.

So move destroy_workqueue() to destructor where rtnl_lock is not held any more,
suggested by Eric.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 17:26:01 -07:00
Eric Dumazet 00ae702847 bonding: bond_xmit_roundrobin() fix
Commit a2fd940f (bonding: fix broken multicast with round-robin mode)
added a problem on litle endian machines.

drivers/net/bonding/bond_main.c:4159: warning: comparison is always
false due to limited range of data type

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-31 03:23:56 -07:00
Andy Gospodarek a2fd940f4c bonding: fix broken multicast with round-robin mode
Round-robin (mode 0) does nothing to ensure that any multicast traffic
originally destined for the host will continue to arrive at the host when
the link that sent the IGMP join or membership report goes down.  One of
the benefits of absolute round-robin transmit.

Keeping track of subscribed multicast groups for each slave did not seem
like a good use of resources, so I decided to simply send on the
curr_active slave of the bond (typically the first enslaved device that
is up).  This makes failover management simple as IGMP membership
reports only need to be sent when the curr_active_slave changes.  I
tested this patch and it appears to work as expected.

Originally reported by Lon Hohberger <lhh@redhat.com>.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Lon Hohberger <lhh@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-27 16:39:15 -07:00
Frans Pop 2381a55c88 net/various: remove trailing space in messages
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-24 14:10:38 -07:00
Jiri Pirko 32a806c194 bonding: flush unicast and multicast lists when changing type
After the type change, addresses in unicast and multicast lists wouldn't make
sense, not to mention possible different lenghts. So flush both lists here.

Note "dev_addr_discard" will be very soon replaced by "dev_mc_flush" (once
mc_list conversion will be done).

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-21 18:31:34 -07:00
stephen hemminger 502a2ffd73 ipv6: convert idev_list to list macros
Convert to list macro's for the list of addresses per interface
in IPv6.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-20 15:45:09 -07:00
Jiri Pirko 3ca5b4042e bonding: check return value of nofitier when changing type
This patch adds the possibility to refuse the bonding type change for
other subsystems (such as for example bridge, vlan, etc.)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-18 20:00:02 -07:00
Jiri Pirko 93d9b7d7a8 net: rename notifier defines for netdev type change
Since generally there could be more netdevices changing type other
than bonding, making this event type name "bonding-unrelated"

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-18 20:00:01 -07:00
Andi Kleen 28812fe11a driver-core: Add attribute argument to class_attribute show/store
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.

Also drivers can extend the attributes with own data fields
and use that in the low level function.

This makes the class attributes the same as sysdev_class attributes
and plain attributes.

This will allow further cleanups in drivers.

Full tree sweep converting all users.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:48 -08:00
Patrick McHardy 8d6184e488 bonding: fix device leak on error in bond_create()
When the register_netdevice() call fails, the newly allocated device is
not freed.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-27 02:52:05 -08:00
Ajit Khaparde 35cfabdc5e bonding: Remove net_device_stats from bonding struct
There is no need to maintain stats in the bonding structure.
Use the instance of net_device_stats in netdevice.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-03 20:32:27 -08:00
David S. Miller 05ba712d7e Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-01-28 06:12:38 -08:00
stephen hemminger b473946a08 bonding: bond_open error return value
The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-28 05:55:54 -08:00
Alexey Dobriyan 2c8c1e7297 net: spread __net_init, __net_exit
__net_init/__net_exit are apparently not going away, so use them
to full extent.

In some cases __net_init was removed, because it was called from
__net_exit code.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17 19:16:02 -08:00
David S. Miller d4a66e752d Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/benet/be_cmds.h
	include/linux/sysctl.h
2010-01-10 22:55:03 -08:00
Andy Gospodarek 1f3c8804ac bonding: allow arp_ip_targets on separate vlans to use arp validation
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation.  A configuration like this, now works:

BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1

Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03 21:17:16 -08:00
Dan Carpenter c99a3d2e04 bond_3ad.c avoid possible null deref
A few lines earlier we assume that best->slave could be either null or non-null so
we should check it here as well.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-26 20:24:46 -08:00
Joe Perches a4aee5c808 drivers/net/bonding/: : use pr_fmt
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from pr_<level>s
Consolidate long format strings
Remove some extra tab indents
Remove some unnecessary ()s from pr_<level>s arguments
Align pr_<level> arguments

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-13 20:06:07 -08:00
Linus Torvalds 4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
Thadeu Lima de Souza Cascardo 94e2bd6888 tree-wide: fix some typos and punctuation in comments
fix some typos and punctuation in comments

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:48 +01:00
Joe Perches 8e95a2026f drivers/net: Move && and || to end of previous line
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.

Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)

Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:01 -08:00
Eric W. Biederman 15449745e5 net: Simplify the bond drivers pernet operations.
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-01 16:15:53 -08:00
David S. Miller 3505d1a9fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/sfc/sfe4001.c
	drivers/net/wireless/libertas/cmd.c
	drivers/staging/Kconfig
	drivers/staging/Makefile
	drivers/staging/rtl8187se/Kconfig
	drivers/staging/rtl8192e/Kconfig
2009-11-18 22:19:03 -08:00