We currently have register offset information only for BAM IPs with revision
1.4.0. We add register offset table entries for the legacy (v1.3.0) version
of BAM IPs found on SoCs like APQ8064 and MSM8960.
The register offset table pointers are stored in DT data corresponding to the
BAM IP version specified in the compatible string.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The BAM DMA IP comes in different versions. The register offset layout varies
among these versions. The layouts depend on which generation/family of SoCs they
belong to.
The current SoCs(like 8084, 8074) have a layout where the Top level registers
come in the beginning of the address range, followed by pipe and event
registers. The BAM revision numbers fall above 1.4.0.
The older SoCs (like 8064, 8960) have a layout where the pipe registers come
first, and the top level come later. These have BAM revision numbers lesser than
1.4.0.
It isn't suitable to have macros provide the register offsets with the layouts
changed. Future BAM revisions may have different register layouts too. The
register addresses are now calculated by referring a table which contains a base
offset and multipliers for pipe/evnt/ee registers.
We have a common function bam_addr() which computes addresses for all the
registers. When computing address of top level/ee registers, we pass 0 to the
pipe argument in addr() since they don't have any multiple instances.
Some of the unused register definitions are removed. We can add new registers as
we need them.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
[for nvidia]
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for end of transaction (EOT) and notify when done (NWD)
hardware descriptor flags.
The EOT flag requests that the peripheral assert an end of transaction interrupt
when that descriptor is complete. It also results in special signaling protocol
that is used between the attached peripheral and the core using the DMA
controller. Clients will specify DMA_PREP_INTERRUPT to enable this flag.
The NWD flag requests that the peripheral wait until the data has been fully
processed by the peripheral before moving on to the next descriptor. Clients
will specify DMA_PREP_FENCE to enable this flag.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller
found in the MSM 8x74 platforms.
Each BAM DMA device is associated with a specific on-chip peripheral. Each
channel provides a uni-directional data transfer engine that is capable of
transferring data between the peripheral and system memory (System mode), or
between two peripherals (BAM2BAM).
The initial release of this driver only supports slave transfers between
peripherals and system memory.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Archit Taneja