For drivers using software encryption for multicast TX, such
as mac80211_hwsim, mac80211 needs to duplicate the multicast
frames on each link, if MLO is enabled. Do this, but don't
just make it dependent on the key but provide a separate flag
for drivers to opt out of this.
This is not very efficient, I expect that drivers will do it
in firmware/hardware or at least with DMA engine assistence,
so this is mostly for hwsim.
To make this work, also implement the SNS11 sequence number
space that an AP MLD shall have, and modify the API to the
__ieee80211_subif_start_xmit() function to always require the
link ID bits to be set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clarify the link ID behaviour in control port TX, we need it
to select the link to transmit on for both MLD and non-MLD
receivers, but select the link address as the SA only if the
receiver is not an MLD.
Fixes: 67207bab93 ("wifi: cfg80211/mac80211: Support control port TX from specific link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the frame is going to be dropped anyway because
ieee80211_lookup_ra_sta() returned an error (and
even though it's a bit racy, it will likely continue
to do so), return the error out instead of just
silently dropping the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a non-MLO client, the A2 must be set to the BSSID
of the link since no translation will happen in lower layers
and it's needed that way for encryption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few places we need to use the AP (MLD) address, not the
deflink BSSID, the link address translation will happen later.
To make that work properly for fast-xmit, set up the ap_addr
in the vif.cfg earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might seem a bit pointless to do a multi-link operation
connection with just a single link, but this is already a
big change, so for now, limit MLO connections to a single
link.
Extending that to multiple links will require
* work on parsing the multi-link element with STA profile
properly, including element fragmentation;
* checking the per-link status in the multi-link element
* implementing logic to have active/inactive links to let
drivers decide which links should be active;
* implementing multicast RX deduplication;
* and likely more.
For now this is still useful since it lets us do multi-link
connections for the purposes of testing APIs and the higher
layers such as wpa_supplicant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an MLO AP is transmitting to a non-MLO station, addr2 should be set
to a link address. This should be done before the frame is encrypted as
otherwise aad verification would fail. In case of software encryption
this can't be left for the device to handle, and should be done by
mac80211 when building the frame hdr.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag here is currently per interface, but the way we
set and clear it means it should be per link, so change
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow link source address on TX.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of authentication with a legacy station, link addressed EAPOL
frames should be sent. Support it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, multicast traffic is handled very differently from normal traffic,
especially if at least one client is in powersave mode.
This means that multicast packets can be buffered a lot longer than normal
unicast packets, and can eat up the AQL budget very quickly because of the low
data rate.
Along with the recent change to maintain a global PHY AQL limit, this can lead
to significant latency spikes for unicast traffic.
Since queueing multicast to hardware is currently not constrained by AQL limits
anyway, let's just exclude it from the AQL pending airtime calculation entirely.
Fixes: 8e4bac0671 ("wifi: mac80211: add a per-PHY AQL limit to improve fairness")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220713083444.86129-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to maintain fairness, the amount of queueing needs to be limited
beyond the simple per-station AQL budget, otherwise the driver can simply
repeatedly do scheduling rounds until all queues that have not used their
AQL budget become eligble.
To be conservative, use the high AQL limit for the first txq and add half
of the low AQL for each subsequent queue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows proper deficit accounting to ensure that they don't carry their
deficit until the next time they become active
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When queueing packets for a station, deficit only gets added once the packets
have been transmitted, which could be much later. During that time, a lot of
temporary unfairness could happen, which could lead to bursty behavior.
Fix this by subtracting the aql_tx_pending when checking the deficit in tx
scheduling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
32 bit is more than enough range for the airtime deficit
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take a few bits out of the control.flags to add the link ID
to TX frame metadata, so drivers don't need to look it up
by the address themselves. Implement that lookup where it's
needed, for internal frame TX, and set it to "unspecified"
for data transmissions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface is an MLD, then we don't know which band
the frame will be transmitted on, and we don't know how to
look up the band. Set the band information to zero in that
case, the driver cannot rely on it anyway.
No longer inline ieee80211_tx_skb_tid() since it's even
bigger now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_build_hdr() we do the same thing for all
interface types except for AP_VLAN, but we can simplify
the code by pulling the common thing in front of the
switch and overriding it for AP_VLAN. This will also
simplify the code for MLD here later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLD, we might eventually not really know the band on status,
but some code assumes it's there. Move the sband lookup deep to
the code that actually needs it, to make it clear where exactly
it's needed and for what purposes.
For rate control, at least initially we won't support it in MLO,
so that won't be an issue.
For TX monitoring, we may have to elide the rate and/or rely on
ieee80211_tx_status_ext() for rate information.
This also simplifies the function prototypes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If statement is meaningless because the code will goto out regardless of
whether fast_tx is NULL or not.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220413091902.27438-1-hbh25y@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new fields in struct beacon_data to store all MBSSID elements.
Generate a beacon template which includes all MBSSID elements.
Move CSA offset to reflect the MBSSID element length.
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Money Wang <money.wang@mediatek.com>
Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org
[small cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The time values used by the airtime fairness code only need to be accurate
enough to cover station activity detection.
Using ktime_get_coarse_boottime_ns instead of ktime_get_boottime_ns will
drop the accuracy down to jiffies intervals, but at the same time saves
a lot of CPU cycles in a hot path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20211217114258.14619-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since retransmission clears info->control, rate control needs to be called
again, otherwise the driver might crash due to invalid rates.
Cc: stable@vger.kernel.org # 5.14+
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Robert W <rwbugreport@lost-in-the-void.net>
Fixes: 03c3911d2d ("mac80211: call ieee80211_tx_h_rate_ctrl() when dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20211122204323.9787-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The codepaths for rx with decap offload and tx with itxq were not updating
the counters for the throughput led trigger.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211113063415.55147-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
-----BEGIN PGP SIGNATURE-----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=ZXrI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define LC band which is a draft under IEEE 802.11bb.
Current NL80211_BAND_LC is a placeholder band and
will be more defined IEEE 802.11bb progresses.
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Link: https://lore.kernel.org/r/20211018100143.7565-2-srini.raju@purelifi.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split __ieee80211_beacon_get() into a separate function for AP mode
ieee80211_beacon_get_ap().
Also, move the code common to all modes (AP, adhoc and mesh) to
a separate function ieee80211_beacon_get_finish().
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20211006040938.9531-2-alokad@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic for starting aggregation sessions was recently moved from minstrel_ht
to mac80211, into the subif tx handler just after the sta lookup.
Unfortunately this didn't work for mesh interfaces, since the sta lookup is
deferred until a much later point in time on those.
Fix this by also calling the aggregation check right after the deferred sta
lookup.
Fixes: 08a46c6420 ("mac80211: move A-MPDU session check from minstrel_ht to mac80211")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210629112853.29785-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
offload_flags has been introduced to indicate encap status of each interface.
An interface can encap offload at runtime, or if it has some extra limitations
it can simply override the flags, so it's more flexible to check offload_flags
in Tx path.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/177785418cf407808bf3a44760302d0647076990.1623961575.git.ryder.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_tx_h_rate_ctrl() get called on dequeue to improve
performance since it reduces the turnaround time for rate control.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20210617163113.75815-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This avoids calling back into tx handlers from within the rate control module.
Preparation for deferring rate control until tx dequeue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210617163113.75815-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx queue")
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
-----BEGIN PGP SIGNATURE-----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=b0NQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous commit to not apply flow control to management frames
that are going over TXQs (which is currently only the case for
iwlwifi, I think) broke things, with iwlwifi firmware crashing on
certain frames. As it turns out, that was due to the frame being
too short: space for the MIC wasn't added at the end of encrypted
management frames.
Clearly, this is due to using the 'frags' queue - this is meant
only for frames that have already been processed for TX, and the
code in ieee80211_tx_dequeue() just returns them. This caused all
management frames to now not get any TX processing.
To fix this, use IEEE80211_TX_INTCFL_NEED_TXPROCESSING (which is
currently used only in other circumstances) to indicate that the
frames need processing, and clear it immediately after so that,
at least in theory, MMPDUs can be fragmented.
Fixes: 73bc9e0af5 ("mac80211: don't apply flow control on management frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210416134702.ef8486a64293.If0a9025b39c71bb91b11dd6ac45547aba682df34@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers, for example mt76, use the skb priority field, and
expects that to be consistent with the skb queue mapping. On some
frame injection code paths that was not true, and it broke frame
injection. Now the skb queue mapping is set according to the skb
priority value when the frame is injected. The skb priority value
is also derived from the frame data for all frame types, as it
was done prior to commit dbd50a851c (only allocate one queue
when using iTXQs). Fixes frame injection with the mt76 driver on
MT7610E chipset.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210401164455.978245-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases (depending on the driver, but it's true e.g. for
iwlwifi) we're using an internal TXQ for management packets,
mostly to simplify the code and to have a place to queue them.
However, it appears that in certain cases we can confuse the
code and management frames are dropped, which is certainly not
what we want.
Short-circuit the processing of management frames. To keep the
impact minimal, only put them on the frags queue and check the
tid == management only for doing that and to skip the airtime
fairness checks, if applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210319232800.0e876c800866.Id2b66eb5a17f3869b776c39b5ca713272ea09d5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable result is being assigned a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210328213729.65819-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4 ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for STBC encoding to the radiotap tx parse
function. Prior to this change adding the STBC flag to the radiotap
header did not encode frames with STBC.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210125150744.83065-1-borgers@mi.fu-berlin.de
[use u8_get_bits/u32_encode_bits instead of manually shifting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch unifies sending control port frames
over nl80211 and AF_PACKET sockets a little more.
Before this patch, EAPOL frames got QoS prioritization
only when using AF_PACKET sockets.
__ieee80211_select_queue only selects a QoS-enabled queue
for control port frames, when the control port protocol
is set correctly on the skb. For the AF_PACKET path this
works, but the nl80211 path used ETH_P_802_3.
Another check for injected frames in wme.c then prevented
the QoS TID to be copied in the frame.
In order to fix this, get rid of the frame injection marking
for nl80211 ctrl port and set the correct ethernet protocol.
Please note:
An erlier version of this path tried to prevent
frame aggregation for control port frames in order to speed up
the initial connection setup a little. This seemed to cause
issues on my older Intel dvm-based hardware, and was therefore
removed again. Future commits which try to reintroduce this
have to check carefully how hw behaves with aggregated and
non-aggregated traffic for the same TID.
My NIC: Intel(R) Centrino(R) Ultimate-N 6300 AGN, REV=0x74
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20210206115112.567881-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for LDPC encoding to the radiotap tx parse
function. Piror to this change adding the LDPC flag to the radiotap
header did not encode frames with LDPC.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20201219170710.11706-1-borgers@mi.fu-berlin.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A sorted flow list is only needed to drop packets in the biggest flow when
hitting the overmemory condition.
By scanning flows only when needed, we can avoid paying the cost of
maintaining the list under normal conditions
In order to avoid scanning lots of empty flows and touching too many cold
cache lines, a bitmap of flows with backlog is maintained
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simplifies the code and prepares for a rework of scanning for flows on
overmemory drop.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check if atf has been disabled in __ieee80211_schedule_txq() in order to
avoid a given sta is always put to the beginning of the active_txqs list
and never moved to the end since deficit is not decremented in
ieee80211_sta_register_airtime()
Fixes: b4809e9484 ("mac80211: Add airtime accounting and scheduling to TXQs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/93889406c50f1416214c079ca0b8c9faecc5143e.1608975195.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_tx_h_select_key drops any non-mgmt packets without a key when
encryption is used. This is wrong for nulldata packets that can't be
encrypted and are sent out for probing clients and indicating 4-address
mode.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Fixes: a0761a3017 ("mac80211: drop data frames without key on encrypted links")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218191525.1168-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commits
d3fd65484c ("net: core: add dev_sw_netstats_tx_add")
451b05f413 ("net: netdevice.h: sw_netstats_rx_add helper)
have added API to update net device per-cpu TX/RX stats.
Use core API instead of ieee80211_tx/rx_stats().
Signed-off-by: Lev Stipakov <lev@openvpn.net>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20201113214623.144663-1-lev@openvpn.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl+uSqIACgkQB8qZga/f
l8QBOw/6AwlcQWMjqdb6H/QRORA81E4tX2+alHbeBai7KSI+9E1Jtakmn5qKQ4iH
IjpNWPsclj4zKhgbKaariIn/bZEk8OhzmDpssnHTMpuo3iuCmuzFaDdZd9Uun2Ad
tr3bqfHaom1MhWRF/FuBSHcnk599qRnsk+RY7/6dhjiPlWOWJvsfpuo1KblVoFWU
wYDX+W2oYDAx44O/6AGJ0Zctwf6m7Kyzb2aMIqv2fwacBoDvyVdTIT/4NroV9INI
QvIY4Gi8hoCDQX39zwaxSWOq7uFLYHwUozzZxktS5c4N3eSVFs80jmdiQiMKmKRQ
A+R+ZcuFBcC+6+Wt4x+20T2mF6pUvSaIDA4jegCbDL4jQlp+023XTMlV42cnpP0z
hFZgBWJszLnLtj4KW/v3sXefZ1Pxl0WD4BHNqz8SMzMUaWalrXP4Gt2bnjB7Bx1N
2M/DjW570eNZeZ9ZFcvkwHysCWMzHKmh5sPXnOitrs4s2hweIrO7wnMlYVLAGF1J
m8jUoqpI9Cc7dFEg0inaSIddcjobcx9i2eG14zaZnXj0t8WqAbQqI0Lw/mipWXFY
7DfdjFULI+Yru46TAFbiisFo/2dlijxrIr3d3QK21Cwklb3BPhpiDf83q6HYhNpB
xPs38OCZaNdSL7TwNRcuZ2jmBCf+48SYgse85HQOgdD2QzJv6dU=
=TGgF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some drivers use skb->priority to determine on which queue to send
a frame. An example is mt76x2u (this was tested on an AWUS036ACM).
This means these drivers currently do not adhere to the DONT_REORDER
flag. To fix this, we do not set skb->priority based on the QoS TID
of injected frames when the DONT_REORDER flag is set.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201104061823.197407-5-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_set_qos_hdr sets the QoS TID of all frames based
on the value assigned to skb->priority. This means it will also
overwrite the QoS TID of injected frames. The commit 753ffad3d6
("mac80211: fix TID field in monitor mode transmit") prevented
injected frames from being modified because of this by setting
skb->priority to the TID of the injected frame, which assured the
QoS TID will not be changed to a different value. Unfortunately,
this workaround complicates the handling of injected frames because
we can't set skb->priority without affecting the TID value in the
QoS field of injected frames.
To avoid this, and to simplify the next patch, detect if a frame is
injected in ieee80211_set_qos_hdr and if so do not change its QoS
field.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201104061823.197407-4-Mathy.Vanhoef@kuleuven.be
[fix typos in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new radiotap flag to indicate injected frames must not be
reordered relative to other frames that also have this flag set,
independent of priority field values in the transmitted frame.
Parse this radiotap flag and define and set a corresponding Tx
control flag. Note that this flag has recently been standardized
as part of an update to radiotap.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201104061823.197407-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ieee80211_skb_resize() is called from ieee80211_build_hdr()
the skb has no 802.11 header yet, in fact it consist only of the
payload as the ethernet frame is removed. As such, we're using
the payload data for ieee80211_is_mgmt(), which is of course
completely wrong. This didn't really hurt us because these are
always data frames, so we could only have added more tailroom
than we needed if we determined it was a management frame and
sdata->crypto_tx_tailroom_needed_cnt was false.
However, syzbot found that of course there need not be any payload,
so we're using at best uninitialized memory for the check.
Fix this to pass explicitly the kind of frame that we have instead
of checking there, by replacing the "bool may_encrypt" argument
with an argument that can carry the three possible states - it's
not going to be encrypted, it's a management frame, or it's a data
frame (and then we check sdata->crypto_tx_tailroom_needed_cnt).
Reported-by: syzbot+32fd1a1bfe355e93f1e2@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20201009132538.e1fd7f802947.I799b288466ea2815f9d4c84349fae697dca2f189@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending EAPOL frames via NL80211 they are treated as injected
frames in mac80211. Due to commit 1df2bdba52 ("mac80211: never drop
injected frames even if normally not allowed") these injected frames
were not assigned a sta context in the function ieee80211_tx_dequeue,
causing certain wireless network cards to always send EAPOL frames in
plaintext. This may cause compatibility issues with some clients or
APs, which for instance can cause the group key handshake to fail and
in turn would cause the station to get disconnected.
This commit fixes this regression by assigning a sta context in
ieee80211_tx_dequeue to injected frames as well.
Note that sending EAPOL frames in plaintext is not a security issue
since they contain their own encryption and authentication protection.
Cc: stable@vger.kernel.org
Fixes: 1df2bdba52 ("mac80211: never drop injected frames even if normally not allowed")
Reported-by: Thomas Deutschmann <whissi@gentoo.org>
Tested-by: Christian Hesse <list@eworm.de>
Tested-by: Thomas Deutschmann <whissi@gentoo.org>
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201019160113.350912-1-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now just skip the duration calculation for frames
transmitted on the S1G band and avoid a warning.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-11-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.
Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This simplifies the checks in the encap offload tx handler and allows using
it in cases where software crypto is used for multicast packets, e.g. when
using an AP_VLAN.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the last_tx timestamp to avoid tearing down the aggregation session
early. Fall back to the slow path if the session setup is still running
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Already parse the radiotap header in ieee80211_monitor_select_queue.
In a subsequent commit this will allow us to add a radiotap flag that
influences the queue on which injected packets will be sent.
This also fixes the incomplete validation of the injected frame in
ieee80211_monitor_select_queue: currently an out of bounds memory
access may occur in in the called function ieee80211_select_queue_80211
if the 802.11 header is too small.
Note that in ieee80211_monitor_start_xmit the radiotap header is parsed
again, which is necessairy because ieee80211_monitor_select_queue is not
always called beforehand.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-6-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the IEEE80211_TX_CTRL_NO_SEQNO flag in ieee80211_tx_info to mark
probe requests whose sequence number must not be overwritten. This
provides consistency with the radiotap flag that can be set to indicate
that the sequence number of an injected frame should not be overwritten.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-4-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check if the Tx control flag is set to prevent sequence number overwrites,
and if so, do not assign a new sequence number to the transmitted frame.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-3-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_tx_dequeue there is a check to see if the dequeued frame
is allowed in the current state. Injected frames that are normally
not allowed are being be dropped here. Fix this by checking if a
frame was injected and if so always allowing it.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-1-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AQL does not take into account that most HT/VHT/HE traffic is A-MPDU aggregated.
Because of that, the per-packet airtime overhead is vastly overestimated.
Improve it by assuming an average aggregation length of 16 for non-legacy
traffic if not using the VO AC queue.
This should improve performance with high data rates, especially with multiple
stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200724182816.18678-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allocated ack_frame id from local->ack_status_frames is not really
stored in the tx_info for 802.3 Tx path. Due to this, tx ack status
is not reported and ack_frame id is not freed for the buffers requiring
tx ack status. Also move the memset to 0 of tx_info before
IEEE80211_TX_CTL_REQ_TX_STATUS flag assignment.
Fixes: 50ff477a86 ("mac80211: add 802.11 encapsulation offloading support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Link: https://lore.kernel.org/r/1595427617-1713-1-git-send-email-vthiagar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using 802.1X over mesh networks, at first an ordinary
mesh peering is established, then the 802.1X EAPOL dialog
happens, afterwards an authenticated mesh peering exchange
(AMPE) happens, finally the peering is complete and we can
set the STA authorized flag.
As 802.1X is an intermediate step here and key material is
not yet exchanged for stations we have to skip mesh path lookup
for these EAPOL frames. Otherwise the already configure mesh
group encryption key would be used to send a mesh path request
which no one can decipher, because we didn't already establish
key material on both peers, like with SAE and directly using AMPE.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200617082637.22670-2-markus.theil@tu-ilmenau.de
[remove pointless braces, remove unnecessary local variable,
the list can only process one such frame (or its fragments)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg