Extract the code that sets up the IOMMU infrastructure from IORT, since
it can be reused by VIOT. Move it one level up into a new
acpi_iommu_configure_id() function, which calls the IORT parsing
function which in turn calls the acpi_iommu_fwspec_init() helper.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210618152059.1194210-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Extract generic DMA setup code out of IORT, so it can be reused by VIOT.
Keep it in drivers/acpi/arm64 for now, since it could break x86
platforms that haven't run this code so far, if they have invalid
tables.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210618152059.1194210-2-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.
This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.
So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.
[nsaenz: unified implementation with DT's counterpart]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some HW devices are created as child devices of proprietary busses,
that have a bus specific policy defining how the child devices
wires representing the devices ID are translated into IOMMU and
IRQ controllers device IDs.
Current IORT code provides translations for:
- PCI devices, where the device ID is well identified at bus level
as the requester ID (RID)
- Platform devices that are endpoint devices where the device ID is
retrieved from the ACPI object IORT mappings (Named components single
mappings). A platform device is represented in IORT as a named
component node
For devices that are child devices of proprietary busses the IORT
firmware represents the bus node as a named component node in IORT
and it is up to that named component node to define in/out bus
specific ID translations for the bus child devices that are
allocated and created in a bus specific manner.
In order to make IORT ID translations available for proprietary
bus child devices, the current ACPI (and IORT) code must be
augmented to provide an additional ID parameter to acpi_dma_configure()
representing the child devices input ID. This ID is bus specific
and it is retrieved in bus specific code.
By adding an ID parameter to acpi_dma_configure(), the IORT
code can map the child device ID to an IOMMU stream ID through
the IORT named component representing the bus in/out ID mappings.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-6-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is nothing PCI specific in iort_msi_map_rid().
Rename the function using a bus protocol agnostic name,
iort_msi_map_id(), and convert current callers to it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-4-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
iort_get_device_domain() is PCI specific but it need not be,
since it can be used to retrieve IRQ domain nexus of any kind
by adding an irq_domain_bus_token input to it.
Make it PCI agnostic by also renaming the requestor ID input
to a more generic ID name.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci/msi.c
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-3-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.254582722@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HiSilicon erratum 162001800 describes the limitation of
SMMUv3 PMCG implementation on HiSilicon Hip08 platforms.
On these platforms, the PMCG event counter registers
(SMMU_PMCG_EVCNTRn) are read only and as a result it
is not possible to set the initial counter period value
on event monitor start.
To work around this, the current value of the counter
is read and used for delta calculations. OEM information
from ACPI header is used to identify the affected hardware
platforms.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[will: update silicon-errata.txt and add reason string to acpi match]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for the SMMU Performance Monitor Counter Group
information from ACPI. This is in preparation for its use
in the SMMUv3 PMU driver.
Signed-off-by: Neil Leeder <nleeder@codeaurora.org>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On some platforms msi parent address regions have to be excluded from
normal IOVA allocation in that they are detected and decoded in a HW
specific way by system components and so they cannot be considered normal
IOVA address space.
Add a helper function that retrieves ITS address regions - the msi
parent - through IORT device <-> ITS mappings and reserves it so that
these regions will not be translated by IOMMU and will be excluded from
IOVA allocations. The function checks for the smmu model number and
only applies the msi reservation if the platform requires it.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[For the ITS part]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some functions definition indentations are using a style that is frowned
upon with return value type/storage class specifier in a separate line.
Reindent the function definitions to fix them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Current ACPI DMA configuration set-up device DMA capabilities through
kernel defaults that do not take into account platform specific DMA
configurations reported by firmware.
By leveraging the ACPI acpi_dev_get_dma_resources() API, add code
in acpi_dma_configure() to retrieve the DMA regions to correctly
set-up PCI devices DMA parameters.
Rework the ACPI IORT kernel API to make sure they can accommodate
the DMA set-up required by firmware. By making PCI devices DMA set-up
ACPI IORT specific, the kernel is shielded from unwanted regressions
that could be triggered by parsing DMA resources on arches that were
previously ignoring them (ie x86/ia64), leaving kernel behaviour
unchanged on those arches.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 316ca8804e ("ACPI/IORT: Remove linker section for IORT entries
probing") removed the linker section for IORT entries probing.
Since those IORT entries were the only iort_node_match() interface
users, the iort_node_match() became obsolete and can then be removed.
Remove the ACPI IORT iort_node_match() interface from the kernel.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
The IORT linker section introduced by commit 34ceea275f
("ACPI/IORT: Introduce linker section for IORT entries probing")
was needed to make sure SMMU drivers are registered (and therefore
probed) in the kernel before devices using the SMMU have a chance
to probe in turn.
Through the introduction of deferred IOMMU configuration the linker
section based IORT probing infrastructure is not needed any longer, in
that device/SMMU probe dependencies are managed through the probe
deferral mechanism, making the IORT linker section infrastructure
unused, so that it can be removed.
Remove the unused IORT linker section probing infrastructure
from the kernel to complete the ACPI IORT IOMMU configure probe
deferral mechanism implementation.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
By allowing platform MSI domain to be created on ACPI platforms,
a platform device MSI domain can be set-up when it is probed.
In order to do that, the MSI domain the platform device connects
to should be retrieved, so the iort_get_platform_device_domain() is
introduced to retrieve the domain from the IORT kernel layer.
With the domain retrieved, we need a proper way to set the
domain to platform device.
Given that some platform devices (irqchips) require the MSI irqdomain
to be their interrupt parent domain, the MSI irqdomain should be
determined before platform device is probed but after the platform
device is allocated which means that the code setting up the MSI
irqdomain, ie acpi_configure_pmsi_domain() should be called in
acpi_platform_notify() (that is triggered after adding a device but
before the respective driver is probed) for the platform MSI domain
code set-up path to work properly.
Acked-by: Rafael J. Wysocki <rafael@kernel.org> [for glue.c]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
For devices connecting to an ITS, the devices need to identify themself
through a devid; this devid is represented in the IORT table in named
component node [1] for platform devices, so this patch adds code that
scans the IORT table to retrieve the devices devid.
Add an IORT interface to collect ITS devices devid to carry out platform
devices MSI mappings with IORT tables.
[1]: https://static.docs.arm.com/den0049/b/DEN0049B_IO_Remapping_Table.pdf
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log/dropped ITS changes]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
The introduction of acpi_dma_configure() allows to configure DMA
and related IOMMU for any device that is DMA capable. To achieve
that goal it ensures DMA masks are set-up to sane default values
before proceeding with IOMMU and DMA ops configuration.
On x86/ia64 systems, through acpi_bind_one(), acpi_dma_configure() is
called for every device that has an ACPI companion, in that every device
is considered DMA capable on x86/ia64 systems (ie acpi_get_dma_attr() API),
which has the side effect of initializing dma masks also for
pseudo-devices (eg CPUs and memory nodes) and potentially for devices
whose dma masks were not set-up before the acpi_dma_configure() API was
introduced, which may have noxious side effects.
Therefore, in preparation for IORT firmware specific DMA masks set-up,
wrap the default DMA masks set-up in acpi_dma_configure() inside an IORT
specific wrapper that reverts to a NOP on x86/ia64 systems, restoring the
default expected behaviour on x86/ia64 systems and keeping DMA default
masks set-up on IORT based (ie ARM) arch configurations.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
DT based systems have a generic kernel API to configure IOMMUs
for devices (ie of_iommu_configure()).
On ARM based ACPI systems, the of_iommu_configure() equivalent can
be implemented atop ACPI IORT kernel API, with the corresponding
functions to map device identifiers to IOMMUs and retrieve the
corresponding IOMMU operations necessary for DMA operations set-up.
By relying on the iommu_fwspec generic kernel infrastructure,
implement the IORT based IOMMU configuration for ARM ACPI systems
and hook it up in the ACPI kernel layer that implements DMA
configuration for a device.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [ACPI core]
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In ACPI based systems, in order to be able to create platform
devices and initialize them for ARM SMMU components, the IORT
kernel implementation requires a set of static functions to be
used by the IORT kernel layer to configure platform devices for
ARM SMMU components.
Add static configuration functions to the IORT kernel layer for
the ARM SMMU components, so that the ARM SMMU driver can
initialize its respective platform device by relying on the IORT
kernel infrastructure and by adding a corresponding ACPI device
early probe section entry.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Device drivers (eg ARM SMMU) need to know if a specific component
is part of the IORT table, so that kernel data structures are not
initialized at initcalls time if the respective component is not
part of the IORT table.
To this end, this patch adds a trivial function that allows detecting
if a given IORT node type is present or not in the ACPI table, providing
an ACPI IORT equivalent for of_find_matching_node().
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit e647b53227 ("ACPI: Add early device probing
infrastructure") the kernel has gained the infrastructure that allows
adding linker script section entries to execute ACPI driver callbacks
(ie probe routines) for all subsystems that register a table entry
in the respective kernel section (eg clocksource, irqchip).
Since ARM IOMMU devices data is described through IORT tables when
booting with ACPI, the ARM IOMMU drivers must be made able to hook ACPI
callback routines that are called to probe IORT entries and initialize
the respective IOMMU devices.
To avoid adding driver specific hooks into IORT table initialization
code (breaking therefore code modularity - ie ACPI IORT code must be made
aware of ARM SMMU drivers ACPI init callbacks), this patch adds code
that allows ARM SMMU drivers to take advantage of the ACPI early probing
infrastructure, so that they can add linker script section entries
containing drivers callback to be executed on IORT tables detection.
Since IORT nodes are differentiated by a type, the callback routines
can easily parse the IORT table entries, check the IORT nodes and
carry out some actions whenever the IORT node type associated with
the driver specific callback is matched.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For ITS, MSI functionality consists on building domain stack and
during that process we need to reference to domain stack components
e.g. before we create new DOMAIN_BUS_PCI_MSI domain we need to specify
its DOMAIN_BUS_NEXUS parent domain. In order to manage that process
properly, maintain list which elements contain domain token
(unique for MSI domain stack) and ITS ID: iort_register_domain_token()
and iort_deregister_domain_token(). Then retrieve domain token
any time later with ITS ID being key off: iort_find_domain_token().
With domain token and domain type we are able to find corresponding
IRQ domain.
Since IORT is prepared to describe MSI domain on a per-device basis,
use existing IORT helpers and implement two calls:
1. iort_msi_map_rid() to map MSI RID for a device
2. iort_get_device_domain() to find domain token for a device
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
IORT shows representation of IO topology for ARM based systems.
It describes how various components are connected together on
parent-child basis e.g. PCI RC -> SMMU -> ITS. Also see IORT spec.
http://infocenter.arm.com/help/topic/com.arm.doc.den0049b/DEN0049B_IO_Remapping_Table.pdf
Initial support allows to detect IORT table presence and save its
root pointer obtained through acpi_get_table(). The pointer validity
depends on acpi_gbl_permanent_mmap because if acpi_gbl_permanent_mmap
is not set while using IORT nodes we would dereference unmapped pointers.
For the aforementioned reason call acpi_iort_init() from acpi_init()
which guarantees acpi_gbl_permanent_mmap to be set at that point.
Add generic helpers which are helpful for scanning and retrieving
information from IORT table content. List of the most important helpers:
- iort_find_dev_node() finds IORT node for a given device
- iort_node_map_rid() maps device RID and returns IORT node which provides
final translation
IORT support is placed under drivers/acpi/arm64/ new directory due to its
ARM64 specific nature. The code there is considered only for ARM64.
The long term plan is to keep all ARM64 specific tables support
in this place e.g. GTDT table.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Jean-Philippe Brucker