Clean up a few sparse warnings, these following
functions can be made static:
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_add_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_del_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_set_vf_mac_filter' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove date and bump version for mlx4_en driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove date and bump version for mlx4_core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 and mv88e6123 are capable of using EDSA tags when
passing frames from the host to the switch and back.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stopping the vxlan interface we detach it from the socket.
Use RCU_INIT_POINTER() and not rcu_assign_pointer() to do so.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the adapter consumes two tids for every ipv6 offload
connection be it active or passive, calculate tid usage
count accordingly.
Also change the signatures of relevant functions to get
the address family.
Signed-off-by: Rizwan Ansari <rizwana@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp22_port_mii_set() function was added by 2697582144, but the
function directly returns without doing anything. This return was used
when debugging and wasn't removed before sending the patch. Fix this.
Fixes: 2697582144 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mtu is currently not supported in the ibmvnic driver.
Implement .ndo_change_mtu in the driver so that attempting to use ifconfig
to change the mtu will fail and present the user with an error message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing VF's DMA mappings, an already NULLed pointer was checked
again due to an apparent copy&paste error. Consequently, the pf2vf
bulletin DMA mapping was not freed.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFD ABI 0.5 is equivalent to NFD ABI 3.0 but requires that the
driver checks the APP id symbol and makes sure it can support
given app. Most advanced apps will likely require control vNIC
(ability to exchange control messages between the driver and
app FW). Detailed app version checking and capability exchange
is left to app-specific code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver encounters an nfp_app which has a control message handler
defined, allocate a control vNIC. This control channel will be used
to exchange data with the application FW such as flow table programming,
statistics and global datapath control.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thus far the code assumed all vNICs will request similar number of IRQs.
This will be no longer true with control vNICs (where 1 IRQ will suffice).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to be able to create a special vNIC for control messages.
This vNIC should be created before any netdev is registered to allow
nfp_app logic to exchange messages with the FW app before any netdev
is visible to user space. Unfortunately we can't enable IRQs until
we know how many vNICs we will need to spawn.
Divide the function which spawns netdevs for vNICs into three parts:
- vNIC/memory allocation;
- IRQ allocation;
- netdev init and register.
This will help us insert the initialization of the control channel
after IRQ allocation but before netdev init and register.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading fw version from the BAR is trivial. Don't pass it around
through layers of init functions, simply read it again where needed.
This commit has the side effect of each vNIC having the exact NFD
version from its own control memory, rather than all data vNICs
assuming the version of the first one. This should not result in
user-visible changes, though. Capabilities of data vNICs of trival
apps are identical.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX and TX queue controllers are interleaved. Instead of creating
two mappings which map the same area at slightly different offset,
create only one mapping. Always map all queue controllers to simplify
the code and allow reusing the mapping for non-data vNICs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon need to map control vNIC PCI memory as well as data vNIC
memory. Make the function for mapping areas pointed to by an RTsym
reusable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since control vNICs don't have a netdev, they can't use napi and
queuing stack provides. Add simple tasklet-based data receive
and send of control messages with queuing on a skb_list.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Out of the three stages of ifup/ifdown (allocate, configure, start)
- this commit prepares the configuration stage for working with
control vNICs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vNICs used for sending and receiving control messages shouldn't
really have a netdev. Add the ability to initialize vNICs for
netdev-less operation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to be able to inspect the state of descriptor rings of
the control vNIC, so it will use the same interface as data vNICs.
Make sure the code doesn't use netdevs to determine state
of the rings and names things appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to reuse print macros easily with control vNICs make the
macros check if netdev pointer is populated and use dev_* print
functions otherwise.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move nfp_net_vecs_init() after all datapath functions. We will need
to init poll() callbacks from this function soon.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the close path reuse the ring free helpers introduced for runtime
reconfiguration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our open/close implementations have 3 stages:
- allocation/freeing of ring resources, irqs etc.,
- device config,
- device/stack enable (can't fail).
Right now all of those stages are placed in separate functions,
apart from allocation during open. Fix that. It will make it
easier for us to allocate resources for netdev-less vNICs.
Because we want to reuse allocation code in netdev-less vNICs
leave the netif_set_real_num_[rt]x_queues() calls inside open.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon reuse parts of .ndo_stop() for clean up after errors
in .ndo_open(). Reorder the associated functions to make that possible.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.
Tested on an IMX51.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phylib support for the Marvell Alaska X 10 Gigabit PHY (MV88X3310).
This phy is able to operate at 10G, 1G, 100M and 10M speeds, and only
supports Clause 45 accesses.
The PHY appears (based on the vendor IDs) to be two different vendors
IP, with each devad containing several instances.
This PHY driver has only been tested with the RJ45 copper port, fiber
port and a Marvell Armada 8040-based ethernet interface.
It should be noted that to use the full range of speeds, MAC drivers
need to also reconfigure the link mode as per phydev->interface, since
the PHY automatically changes its interface mode depending on the
negotiated speed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the old 10G genphy support to sit beside the new clause 45 library
functions, so all the 10G phy code is together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type and whether the Clause 45 PHY supports the Clause 22 register set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling genphy_aneg_done() for PHYs that do not implement the
Clause 22 register set.
Clause 45 PHYs may implement the Clause 22 register set along with the
Clause 22 extension MMD. Hence, we can't simply block access to the
Clause 22 functions based on the PHY being a Clause 45 PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that queue is less or equal to zero is always true
because queue is a u32; queue is decremented and will wrap around
and never go -ve. Fix this by making queue an int.
Detected by CoverityScan, CID#1428988 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.
This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.
When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.
When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tun actually expects a symmetric hash for queue selecting to work
correctly, otherwise packets belongs to a single flow may be
redirected to the wrong queue. So this patch switch to use
__skb_get_hash_symmetric().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_reset enables device interrupts, ethoc_interrupt may schedule a
NAPI poll before NAPI is enabled in the ethoc_open, which results in
device being unable to send or receive anything until it's closed and
reopened. In case the device is flooded with ingress packets it may be
unable to recover at all.
Move napi_enable above ethoc_reset in the ethoc_open to fix that.
Fixes: a170285772 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register bits used for the frame mode were masked with DSA (0x1)
instead of the mask value (0x3) in the 6085 implementation of
port_set_frame_mode. Fix this.
Fixes: 56995cbc35 ("net: dsa: mv88e6xxx: Refactor CPU and DSA port setup")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_set_vf_rate() for mgmt interface to support rate-limiting
of VF traffic using 'ip' command.
Based on the original work of Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using this extension reduces the object size.
$ size drivers/net/ppp/ppp_mppe.o*
text data bss dec hex filename
5683 216 8 5907 1713 drivers/net/ppp/ppp_mppe.o.new
5808 216 8 6032 1790 drivers/net/ppp/ppp_mppe.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.
Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused, so remove it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been a slow start of cycle and this the first set of fixes for
4.12. Nothing really major here.
wcn36xx
* fix an issue with module reload
brcmfmac
* fix aligment regression on 64 bit systems
iwlwifi
* fixes for memory leaks, runtime PM, memory initialisation and other
smaller problems
* fix IBSS on devices using DQA mode (7260 and up)
* fix the minimum firmware API requirement for 7265D, 3168, 8000 and
8265
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZNpwJAAoJEG4XJFUm622bZ5MIAJAB1eJ8FRIllNZlWszGaZll
E+IjMhXaQNuqkMoepziKy2Lsacrw+sJPVkXqOU7akbwkxHVTDouYQRrsN91y/wab
YqPCZaCjEEjHPPgGEgh4tJX0KJO7TRg4dDq+OYNTyEQu0KZ/UdukXolt4yKzfHjB
eW92eL4XULAzgcFHd1PMrQW+wvUDD//tr53rDP+i+rKAt7xoEz+gpHPgzGFCBWK2
gSE98naqd7fu4OFMtF29m6kXhilSlfh1qqghf5/KjDMu040LRfBf2GuLNJRY6vhD
y+PIu06GfgP6mLR5ERX+60XOKgNoKHSIGni73tot1ruyOQkCDdpdIqoL3oPIIoc=
=1nR6
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.12
It has been a slow start of cycle and this the first set of fixes for
4.12. Nothing really major here.
wcn36xx
* fix an issue with module reload
brcmfmac
* fix aligment regression on 64 bit systems
iwlwifi
* fixes for memory leaks, runtime PM, memory initialisation and other
smaller problems
* fix IBSS on devices using DQA mode (7260 and up)
* fix the minimum firmware API requirement for 7265D, 3168, 8000 and
8265
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the previously prepared infrastructure and offload the gact
trap action to ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use trap/discard flex action to implement trap.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an ACL trap and put it into ip2me trap group.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "trap_id" is 9bits long. So far, this was not a problem since we
used only traps with ids that fit into 8bits. But the ACL traps that are
going to be introduced use the 9th bit.
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check to see of err is set and the subsequent goto is extraneous
as the next statement is where the goto is jumping to. Remove this
redundant check and goto.
Detected by CoverityScan, CID#1437734 ("Identical code for
different branches")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.
Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.
Fixes: f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:
[49.013] i40e 0002:01:00.0: bad reset request 0x00000020
Commit d19cb64b92 ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.
This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.
Fixes: 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b92 ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace disable_irq() which waits for threaded irq handlers with
disable_hardirq() which waits only for hardirq part.
Fixes: 3111912971 ("e1000: use disable_hardirq() for e1000_netpoll()")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some statistics passed to ethtool are garbage because e1000e_get_stats64()
doesn't write them, for example: tx_heartbeat_errors. This leaks kernel
memory to userspace and confuses users.
Do like ixgbe and use dev_get_stats() which first zeroes out
rtnl_link_stats64.
Fixes: 5944701df9 ("net: remove useless memset's in drivers get_stats64")
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Given that all callers of igb_update_stats() pass the same two arguments:
(adapter, &adapter->stats64), the second argument can be removed.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an igb_ptp_tx_hang() function similar to the already existing
igb_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver uses a state bit lock to avoid handling more than one Tx
timestamp request at once. This is required because hardware is limited
to a single set of registers for Tx timestamps.
The state bit lock is not properly cleaned up during
igb_xmit_frame_ring() if the transmit fails such as due to DMA or TSO
failure. In some hardware this results in blocking timestamps until the
service task times out. In other hardware this results in a permanent
lock of the timestamp bit because we never receive an interrupt
indicating the timestamp occurred, since indeed the packet was never
transmitted.
Fix this by checking for DMA and TSO errors in igb_xmit_frame_ring() and
properly cleaning up after ourselves when these occur.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the igb driver has a limitation of only handling one
Tx timestamp at a time. Thus, the driver uses a state bit lock to
enforce that only one timestamp request is honored at a time.
Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying the stack of
a new Tx timestamp. Even a well behaved application which sends only one
timestamp request at once and waits for a response might wake up and
send a new packet before the bit lock is cleared. This results in
needlessly dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver and related hardware has a limitation on Tx PTP
packets which requires we limit to timestamping a single packet at once.
We do this by verifying that we never request a new Tx timestamp while
we still have a tx_hwtstamp_skb pointer.
Unfortunately the driver suffers from a race condition around this. The
tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx()
is called. This function notifies the stack and applications of a new
timestamp. Even a well behaved application that only sends a new request
when the first one is finished might be woken up and possibly send
a packet before we can free the timestamp in the driver again. The
result is that we needlessly ignore some Tx timestamp requests in this
corner case.
Fix this by assigning the tx_hwtstamp_skb pointer prior to calling
skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb
until that function finishes. This ensures that the application is not
woken up until the driver is ready to begin timestamping a new packet.
This ensures that well behaved applications do not accidentally race
with condition to skip Tx timestamps. Obviously an application which
sends multiple Tx timestamp requests at once will still only timestamp
one packet at a time. Unfortunately there is nothing we can do about
this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new wake function is only used by the suspend/resume handlers that
are defined in inside of an #ifdef, which can cause this harmless
warning:
drivers/net/ethernet/intel/igb/igb_main.c:7988:13: warning: 'igb_deliver_wake_packet' defined but not used [-Wunused-function]
Removing the #ifdef, instead using a __maybe_unused annotation
simplifies the code and avoids the warning.
Fixes: b90fa87635 ("igb: Enable reading of wake up packet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions igb_read_phy_reg_gs40g/igb_write_phy_reg_gs40g (which were
removed in 2a3cdea) explicitly selected the required page at every phy_reg
access. Currently, igb_get_phy_id_82575 relays on the fact that page 0 is
already selected. The assumption is not fulfilled for my Lex 3I380CW
motherboard with integrated dual i211 based gigabit ethernet. This leads to igb
initialization failure and network interfaces are not working:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
igb: probe of 0000:02:00.0 failed with error -2
In order to fix it, we explicitly select page 0 before first access to phy
registers.
See also: https://bugzilla.suse.com/show_bug.cgi?id=1009911
See also: http://www.lex.com.tw/products/pdf/3I380A&3I380CW.pdf
Fixes: 2a3cdea ("igb: Remove GS40G specific defines/functions")
Cc: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Matwey V Kornilov <matwey@sai.msu.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The u32 variable v is being checked to see if an error return is
less than zero and this check has no effect because it is unsigned.
Fix this by making v and int (this also matches the type of
cb->bus_number which is assigned to the value in v).
Detected by CoverityScan, CID#1440454 ("Unsigned compared against zero")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a previous commit, we removed support for API versions earlier than
22 for these NICs. By mistake, the *_UCODE_API_MIN definitions were
set to 17. Fix that.
Fixes: 4b87e5af63 ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore. Mistakenly, this was changed to return an
error while fixing another bug.
If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.
Fixes: cd4d23c1ea ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.
Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
recording)
For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.
Fixes: 5c89e7bc55 ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.
This fixes a problem in runtime PM resume flow.
Fixes: 097129c9e6 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.
This fixes some throughput degradation in noisy environments.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Granular QoS per VF feature must be enabled in FW before it can be
used.
Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.
Fixes: 08068cd568 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings (typo) in drivers/net/phy/phy.c:
..//drivers/net/phy/phy.c:259: warning: No description found for parameter 'features'
..//drivers/net/phy/phy.c:259: warning: Excess function parameter 'feature' description in 'phy_lookup_setting'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY may be already enabled by bootloaders which have Ethernet
capability (e.g. current U-Boot). Thus it should be reseted properly
before doing the enabling sequence in the dwmac-sun8i driver, otherwise
the EMAC reset process may fail if no cable is plugged, and then fail
the dwmac-sun8i probing.
Tested on Orange Pi PC, One and Zero. All the boards fail to have
dwmac-sun8i probed with "EMAC reset timeout" without cable plugged
before, and with this fix they're now all able to successfully probe the
EMAC without cable plugged and then use the connection after a cable is
hot-plugged in.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: is not as formal as Signed-off-by:. It is a record that the acker
Reviewed-by: is similar.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since functions never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way we usually allocate an index is by letting the allocation
function return an error instead of an invalid index.
Do the same for RIF index.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear where functions are defined and move misplaced declaration
to their correct place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the firmware file name to be in "mellanox" directory.
This commit is a followup to the linux-firmware commit a4c72696f5f4
("Mellanox: Add firmware for mlxsw_spectrum")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our previous patch (cited below) introduced a regression
for RAW Eth QPs.
Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.
Fixes: 89c557687a ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces 2 changes needed for XDP to be supported for VFs:
a. On VF-side, publish the NDO based on qed outputs
b. On PF-side, request qed to allocate sufficient cids per-VF
to allow the child vfs to support it
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The final addition on the qed front -
- VFs would now require their PFs to provide multiple CIDs
- Based on the availability of connections from PF, determine whether
XDP is feasible and share it with qede via dev_info.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently not mapping their doorbell bar, instead relying
on the small doorbell window they have in their limited regview bar.
In order to increase the number of possible Tx connections [queues]
employeed by VF past 16, we need to start using the doorbell bar if
one such is exposed - VF would communicate this fact to PF which would
return the size-bar internally configured into chip, according to
which the VF would decide whether to actually utilize the doorbell
bar.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the infrastructure for supporting VFs that want to open
multiple transmission queues on the same queue-zone.
At this point, there are no VFs that actually request this functionality,
but later patches would remedy that.
a. VF and PF would communicate the capability during ACQUIRE;
Legacy VFs would continue on behaving as they do today
b. PF would communicate number of supported CIDs to the VF
and would enforce said limitation
c. Whenever VF passes a request for a given queue configuration
it would also pass an associated index within said queue-zone
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the infrastructure a PF maintains for each one of its VFs
to support multiple queue-cids on a single queue-zone.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now we used to have a single VF legacy compatibility mode,
one that affected the place of the Rx producers of those VFs [mostly].
As PF would soon support allocating CIDs for VFs instead of having
a static CID<->queue configuration for them, we'll need to have
an additional legacy mode since existing VFs would need to continue
on using the older mode of operation.
Change the infrastrucutre so that the legacy would be able to indicate
which of the legacy behaviors is needed for a given VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a queue-cid is allocated, assign an index inside that's
CID's queue-zone.
For PFs and VFS, this number is going to be unique and derive
from a per-queue-zone bitmap, while for PF's VFs queues the
number is currently going to constant; Later, we'd add the
capability of a VF to communicate such an index to its PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to need additional information for queue-cids
that a PF creates for its VFs, so start by refactoring existing
logic used for initializing said struct into receiving a structure
encapsulating the VF-specific information that needs to be provided.
This also introduces QED_QUEUE_CID_SELF - each queue-cid would hold
an indication to whether it belongs to the hw-function holding it
[whether that's a PF or a VF], or else what's the VF id it belongs
to.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in allowing a single PF/VF to open multiple queues on
the same queue zone is to add per-hwfn database of queue-cids
as a two-dimensional array where entry would be according to
[queue zone][internal index].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each PF has a bitmap for its own ranges of CIDs, to allow easy grabbing
of an available CID when such is needed. But VFs are not using the same
mechanism, instead relying on hard-coded CIDs [ queue-index == cid ].
As an infrastructure step toward increasing number of CIDs of VFs,
the PF is going to maintain bitmaps for the VF CIDs as well -
the bitmaps would be per-VF and the ranges would be the same [in HW all
VFs of a given PF have the same mapping of CIDs, and the HW is capable
of distinguishing between those according to the VF index]
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the PHYs supported by the SMSC driver have a counter of symbol
errors. This is 16 bit wide and wraps around when it reaches its
maximum value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-By: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 was using the wrong method to perform statistics
snapshot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to the internal PHYs of the 6161 and 6123 go through global 2
SMI registers. Fix the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the GLOBAL2_* macros where they belong, in the related global2.h
header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the GLOBAL_* macros where they belong, in the related global1.h
header. Include it in global2.c which uses GLOBAL_STATUS_IRQ_DEVICE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PORT_* macros where they belong, in the related port.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY_* macros where they belong, in the related phy.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx.h is meant to contains the chip structures and data.
Rename it to chip.h, as for other source/header pairs of the driver.
At the same time, ensure that relative header inclusions are separated
by a newline and sorted alphabetically.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9b4437a5b8 ("geneve: Unify LWT and netdev handling.")
when using COLLECT_METADATA geneve devices are created with too small of
a needed_headroom and too large of a max_mtu. This is because
ip_tunnel_info_af() is not valid with the device level info when using
COLLECT_METADATA and we mistakenly fall into the IPv4 case.
For COLLECT_METADATA, always use the worst case of ipv6 since both
sockets are created.
Fixes: 9b4437a5b8 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
functions m88e1510_get_temp_critical, m88e1510_set_temp_critical and
m88e1510_get_temp_alarm can be made static as they not need to be
in global scope.
Cleans up sparse warnings:
"symbol 'm88e1510_get_temp_alarm' was not declared. Should it be static?"
"symbol 'm88e1510_get_temp_critical' was not declared. Should it be
static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of rewriting write/readq, use linux/io-64-nonatomic-lo-hi.h which
already have them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature. Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.
The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is. The feature eliminates the need for
software to poll the MDIO bus.
Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:
1. It assumes a compatible register set, so PHYs with different registers
may not work.
2. It doesn't allow for hardware errata that have work-arounds implemented
in the PHY driver.
3. It doesn't support multiple register pages. If the PHY core switches
the register set to another page, the EMAC won't know the page has
changed and will still attempt to read the same PHY register.
4. It only checks the copper side of the link, not the SGMII side. Some
PHY drivers (e.g. at803x) may also check the SGMII side, and
report the link as not ready during autonegotiation if the SGMII link
is still down. Phylib then waits for another interrupt to query
the PHY again, but the EMAC won't send another interrupt because it
thinks the link is up.
Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any errors are encountered while walking the device tree structure of
the MDIO bus for children, the code may silently continue, silently
exit, or throw an error and exit. This make it difficult for device
tree writers to know there is an error. Also, it makes any error in a
child entry of the MDIO bus be fatal for all entries. Instead, we
should provide verbose errors describing the error and then attempt to
continue if it all possible. Also, use of_mdio_parse_addr()
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable offloading of TC matching on ipv4 tos or ipv6 traffic-class.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d85b758f72 ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.
Fixes: d85b758f72 ("virtio_net: fix support for small rings")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.
We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().
Fixes: 56ef9c909b ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use of_mdio_parse_addr() in place of an OF read of reg and a bounds
check (which is litterally the exact same thing that
of_mdio_parse_addr() does)
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set initialization state variable to (reflect interrupt initialization) at
correct time (immediately after having configured interrupts). This fixes
problem of inconsistent IRQ allocation in case of [obscure] failure when
negotiating with PF driver during init.
Clean-up of interrupt enablement during initialization & avoid potential
race condition with chip-specific code (i.e. perform interrupt control in
main driver module). Added explanatory comments regarding interrupt
enablement.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
take care of UpDbgLaRdPtr[0-3] restriction for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-06-01
This series contains updates to i40e, i40evf and the "new" AVF virtchnl.
This is the introduction of the Intel(R) Ethernet Adaptive Virtual
Function driver code and device ID, as presented at the NetDEV 1.2
conference in 2016.
http://netdevconf.org/1.2/session.html?anjali-singhai
The idea is to convert the interface between the i40evf driver
and the parent i40e PF driver to be generic, as the i40evf driver
should in the future be able to run on top of other Intel PF
drivers, and negotiate any features beyond a "base expected" set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance API between qedi and qed, allowing qedi to inform device's
firmware when the iSCSI mac is to be changed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storage drivers require images from the nvram in boot-from-SAN
scenarios. This provides the necessary API between qed and the
protocol drivers to perform such reads.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Share several new tidbits with qedf:
- wwpn & wwnn
- Absolute pf-id [this one is actually meant for qedi as well]
- Number of available CQs
While we're at it, now that qedf will be aware of the available CQs
we can add some validation on the inputs it provides.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reads values via HSI splitting this 8-byte into 2 32-bit
values and builds a single u64 field - but it does so by shifting
the lower field instead of the higher.
Luckily, we still don't use these fields for anything - but we're about
to start.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new macro MODULE_ALIAS_TEAM_MODE to unify and simplify the
declaration of team mode alias.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID define and mac_type assignment needed for
Adaptive Virtual Function (VF Base Mode Support).
Also, update version to v3.0.0 in order to indicate
clearly that this is the first driver supporting the AVF
device ID.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This moves a function that is needed for the virtchnl interface
from the i40e PF driver over to the virtchnl.h file.
It was manually verified that the function in question is unchanged
except for the function name and function header, which explains
the slight difference in the number of lines removed/added.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the complete version of the virtchnl.h file
with final renames, and fixes the related code in i40e and i40evf.
It also expands comments, and adds details on the usage of
certain fields.
In addition, due to the changes a couple of casts are needed
to prevent errors found by sparse after renaming some fields.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes up a bunch of whitespace issues introduced
by the previous automated change of name from i40e to virtchnl.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the arguments passed to the validate function
and fixes the caller, as well as uses the new return values added to
virtchnl.h
One other minor tweak, remove a duplicate set to zero of valid_len.
This is in preparation for moving the function to virtchnl.h.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of the conversion, change the arguments
to VF_IS_V1[01] macros and move them to virtchnl.h
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before moving this function over to virtchnl.h, move
some driver specific checks that had snuck into a fairly
generic function, back into the caller of the function.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This morphs all the i40e and i40evf references to/in virtchnl.h
to be generic, using only automated methods. Updates all the
callers to use the new names. A followup patch provides separate
clean ups for messy line conversions from these "automatic"
changes, to make them more reviewable.
Was executed with the following sed script:
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_common.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_main.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
sed -i -f transform_script include/linux/avf/virtchnl.h
transform_script:
----8<----
s/I40E_VIRTCHNL_SUPPORTED_QTYPES/SAVE_ME_SUPPORTED_QTYPES/g
s/I40E_VIRTCHNL_VF_CAP/SAVE_ME_VF_CAP/g
s/I40E_VIRTCHNL_/VIRTCHNL_/g
s/i40e_virtchnl_/virtchnl_/g
s/i40e_vfr_/virtchnl_vfr_/g
s/I40E_VFR_/VIRTCHNL_VFR_/g
s/VIRTCHNL_OP_ADD_ETHER_ADDRESS/VIRTCHNL_OP_ADD_ETH_ADDR/g
s/VIRTCHNL_OP_DEL_ETHER_ADDRESS/VIRTCHNL_OP_DEL_ETH_ADDR/g
s/VIRTCHNL_OP_FCOE/VIRTCHNL_OP_RSVD/g
s/SAVE_ME_SUPPORTED_QTYPES/I40E_VIRTCHNL_SUPPORTED_QTYPES/g
s/SAVE_ME_VF_CAP/I40E_VIRTCHNL_VF_CAP/g
----8<----
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the i40e driver to start using the new virtchnl
interface header file, and removes an already existing duplicate of the
i40e_virtchnl.h file contained in the i40e directory.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This moves a header for i40evf to include/linux/avf/virtchnl.h.
The directory name AVF is an acronym for the Intel(R) Adaptive
Virtual Function.
This first step creates the new file, which is a rename of
drivers/net/ethernet/intel/i40evf/i40e_virtchnl.h to
include/linux/avf/virtchnl.h, and should show up in git
as a rename when using git log --follow.
To keep things building after the move, the changes to the i40evf
driver are made to point to the new include file location.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This drops the i40e_type.h include in anticipation of the next
patch which moves this file to a location where type.h doesn't
exist, and all the places this file is included already include
i40e_type.h before this file.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When BRIDGE is a loadable module, MLXSW_SPECTRUM mustn't be built-in:
drivers/built-in.o: In function `mlxsw_sp_bridge_device_create':
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:145: undefined reference to `br_vlan_enabled'
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:158: undefined reference to `br_multicast_enabled'
drivers/built-in.o: In function `mlxsw_sp_dev_rif_type':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:2972: undefined reference to `br_vlan_enabled'
drivers/built-in.o: In function `mlxsw_sp_inetaddr_vlan_event':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3310: undefined reference to `br_vlan_enabled'
Add Kconfig dependency to enforce usable configurations.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.
This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thoses symbol will be needed for the dwmac-sun8i ethernet driver.
For letting it to be build as module, they need to be exported.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 0c1d70af92 ("net: use dst_cache for vxlan device"),
cached dst entries could be leaked when more than one remote was
present for a given vxlan_fdb entry, causing subsequent netns
operations to block indefinitely and "unregister_netdevice: waiting
for lo to become free." messages to appear in the kernel log.
Fix by properly releasing cached dst and freeing resources in this
case.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add callback to the ethtool flash_device op. This callback uses the mlxfw
module to flash the new firmware file to the device.
As the firmware flash process takes about 20 seconds and ethtool takes the
rtnl lock during the flash_device callback, release the rtnl lock at the
beginning of the flash process and take it again before leaving the
callback. This way, the rtnl is not held during the process. To make sure
the device does not get deleted during the flash process, take a reference
to it before releasing the rtnl lock.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.
Fixes: ada7c19e6d ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're resetting the IGU CAM each time we initialize the PF
device, there's no need to reset the VF SBs again when initializing
IOV.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGU CAM contains an assocaition between hardware SBs
and interrupt lines, and it can be dynamically configured
to allow more interrupts in one entity over another, specifically
for Re-distibution of SBs between a PF and its child VFs.
While we don't yet use this functionality, there are other
clients that do and as such its possible the information
passed from management firmware during initialization in
regard to the possible number of SBs doesn't accurately reflect
the current HW configuration.
The following changes are going to apply to the driver init sequence:
a. PF is going to re-configure all entries belonging to itself and
its child VFs in IGU CAM based on the management firmware info
regarding the number of SBs that are supposed to exist there.
b. PF is going to stop using the SB resource [management firmware
provided information] for anything but the initialization.
Instead, it would use the live-time counters it maintains for
the numbers.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF today holds 2 different arrays - one holding information
about the HW configuration and one holding information about
the SBs that are used by the protocol drivers.
These arrays aren't really connected - e.g., protocol driver
initializing a given SB would not mark the same SB as occupied
in the HW shadow array.
Move into a single array [at least for PFs] - hold the mapping
of the driver-protocol SBs on the HW entry which they configure.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOV code is very intrusive in its manipulation of the status block
database.
Add a new auxiliary function to allow the PF to find an available unused
status block to configure for a specific VF's MSI-x vector.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code assumes there's a known layout for SBs in the IGU,
where all the SBs of a single entity would be laid in consecutive
order of vectors.
While the assumption is still kept by management firmware, we already
have the necessary information to eliminate it, so no reason to keep
it in code.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An additional step for relaxing the IGU order assumption, we now add
an auxiliary function that can be used for finding the HW status block
that's associated with a given MSI-x vector.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qed code, sb_id means 2 different things:
- An interrupt vector [usually when received as a parameter from
a protocol driver, but not only] that's associated with a status
block.
- An index to a status block entity existing in HW.
This patch renames the references to the HW entity, adding an 'igu_'
prefix to allow an easier distinction.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a first step for relaxing various assumptions done by driver
about the IGU mapping, the driver is now going to read the entire
IGU into a shadow copy, and mark in its database each status block
that's relevant for it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the portions controlling interrupt enablement form those
controlling the ability of HW to generate attentions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit 55454a5658 ("ppp: avoid dealock on recursive xmit"),
the PPP xmit path is protected by wrapper functions which disable the
bh already. So it is unnecessary to disable the bh again in the real
xmit path.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
To fix it, the usleep_range is replaced with udelay.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux-firmware maintainers prefer to have a subdirectory for
firmware files. Code is changed here to pick firmware file from
a subdirectory. Firmware file with a new loading mechanism will
be submitted inside rsi directory.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP interface need process remain-on-channel firmware event and notify
cfg80211, this will be used in the listen-stage of p2p find procedure.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't need to check if the list is empty separately
as we could use list_first_entry_or_null to cover it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac is being assigned twice, remove redundant 2nd assignment.
Detected by CoverityScan, CID#1437554 ("Incorrect expression")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For SDIO the alignment requirement for transfers from device to host
is configured in firmware. This configuration is limited to minimum
of 4-byte alignment. However, this is not correct for platforms using
64-bit DMA when the minimum alignment should be 8 bytes. This issue
appeared when the ALIGNMENT definition was set according the DMA
configuration. The configuration in firmware was not using that macro
defintion, but a hardcoded value of 4. Hence the driver reported
alignment failures for data coming from the device and causing
transfers to fail.
Fixes: 6e84ab604b ("brcmfmac: properly align buffers on certain platforms
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch
with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs.
The other 2 ports have interfaces that can be configured as SGMII, RGMII, MII
or RMII. Either of these may connect directly to a host processor or
to an external PHY. The SGMII port may interface to a fiber optic transceiver.
This driver currently supports vlan, fdb, mdb & mirror dsa switch operations.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Microchip 9477 Phy included in KSZ9477 Switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free management FW info when app FW load failed.
Fixes: eefbde7e10 ("nfp: add hwmon support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow apps to associate private data with vNICs and move
BPF-specific fields of nfp_net to such structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move bulk of the eBPF offload code out of common vNIC code into
app-specific callbacks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pure move of eBPF offload files to BPF app directory,
only change the names and relative header location.
nfp_asm.h stays in the main dir and it doesn't really
have to include nfp_bpf.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the app print its name in ethtool -i output.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start fleshing out the apps by turning the vNIC init code to
a per-app callback. The two initial apps we have are NIC and
eBPF.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn the function to read number of ports into a generic helper.
While at it make sure we propagate all errors other than -ENOENT.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 7 checks for fall through comments, add the two missing ones.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forgetting to disable preemption around tcf_action_stats_update()
seems to be a common mistake. Add a helper function for updating
stats on all actions of a filter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-05-31
This series contains updates to ixgbe and ixgbevf only.
Scott enables support for TSO & GSO for MPLS encapsulated packets for both
ixgbe and ixgbevf.
Liwei Song fixes an issue where seqcount/seqlock in ixgbe_get_stats64()
are not initialized in time, so move the initialization into probe routine
after the transmit and receive rings are initialized.
Paul cleans up led_[on|off] for X550EM_X, since the firmware configures
the PHY & MAC and we have no PHY access so LED on/off is not supported
with this device.
Emil provides several fixes, starting with enabling RSS on VF to VF
traffic on the same PF. Fixed PHY identification, where the previous
method was unreliable, so use a different register to ensure proper
identification. Cleaned up the logic which could cause us to
skip the link configuration, this skipping over the link configuration
was leaving SFP+ PHY's in an unstable state, so always call
setup_mac_link(). Added RS1 (rate select 1) support for ixgbe. Lastly,
fixed incorrect logic in the setting up of SFP+ link speed.
Mark fixes the thermal sensor event logic, where it was being executed
when there really was no thermal event. So simplify the logic to only
execute when there is a thermal event.
Tony adds additional error checks and reporting when setting a VF MAC
address to ensure that the MAC filter was successfully added. Also
fixed possible truncation warnings, as well as implicit fallthrough
warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-05-31
This series contains updates to i40e and i40evf only.
Jesse provides a couple of fixes, starting with cleaning up duplicate
lines of code. Fixed a missing line which enables RSS as a negotiated
feature. Since the VF does not have any way of reporting FCoE enabled,
so just force the code to always report FCoE as disabled.
Jake provides several fixes and changes, starting with fixing a race
condition in i40e. The hardware has a limitation on transmit PTP packets,
which requires us to limit the driver to timestamping a single packet at
once. This is done using a state bitlock which enforces that only one
timestamp request is honored at a time, unfortunately this suffers from
a race condition. Fixed a corner case where we failed to cleanup the
bit lock after a failed transmit, and resulted in a state bit being
locked forever. Added a new statistic which tracks when a transmit
timestamp request is skipped/ignored, since the driver can only handle
one transmit timestamp request at a time.
Christophe Jaillet fixes a NULL pointer dereference if kzalloc fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-loading of the Marvell DSA driver has stopped working with recent
kernels. This seems to be due to the change of binding for DSA devices,
moving them from the platform bus to the MDIO bus.
In order for module auto-loading to work, we need to provide a MODALIAS
string in the uevent file for the device. However, the device core does
not automatically provide this, and needs each bus_type to implement a
uevent method to generate these strings. The MDIO bus does not provide
such a method, so no MODALIAS string is provided:
.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
In the case of OF-based devices, the solution is easy -
of_device_uevent_modalias() does the work for us. After this is done,
the uevent file looks like this:
.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085
which results in auto-loading of the Marvell DSA driver on Clearfog
platforms.
Fixes: c0405563a6 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add direct #include statements for declarations of csum_tcpudp_magic()
and csum_ipv6_magic(). While the needed #include's are picked up
indirectly for the x86 architecture, they aren't on other
architectures, resulting in compile errors.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert. This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.
This allows ethtool to report the correct link partner auto-negotiation
status.
Fixes: be937f1f89 ("Marvell PHY m88e1111 driver fix")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mlxfw code fails to build without the xz library:
drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2.o: In function `mlxfw_mfa2_xz_dec_run':
:(.text.mlxfw_mfa2_xz_dec_run+0x8): undefined reference to `xz_dec_run'
drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2.o: In function `mlxfw_mfa2_file_component_get':
:(.text.mlxfw_mfa2_file_component_get+0x218): undefined reference to `xz_dec_init'
:(.text.mlxfw_mfa2_file_component_get+0x2c0): undefined reference to `xz_dec_end'
This adds a Kconfig 'select' statement for it, which is also what
the other user of that library has.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the implicit naming convention used in all register sets
specific files, by renaming the mv88e6xxx_ppu_* functions with the
mv88e6xxx_phy_* prefix.
This is simply a s/xxx_ppu/xxx_phy_ppu/ substitution.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mv88e6xxx_phy_ppu_{read,write} are an implementation
of the .phy_{read,write} operations, by renaming them with the mv88e6185
prefix, since 88E6185 it is the reference switch model supported in an
upstream board (ZII Dev Rev B), which makes use of them.
Distinguish the signatures of implementation specific and generic PHY
functions in the phy.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the VTU, PVT and ATU setup, provide a mv88e6xxx_phy_setup
helper which wraps mv88e6xxx_ppu_enable, so that no more PPU-related
functions are exposed outside of phy.c.
Thus make mv88e6xxx_ppu_enable static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next packet length will be used by interface driver, to check if the
next packet still could be aggregated.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Aggregation will wait for next packet until limit aggr size/number reach.
Packet might be drop and also packet dequeue will be stop in some cases.
This patch add timer to flush packets in aggregation list to avoid long
time waiting.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using 4KB packet buffer for data transfer, new chipset have
more device memory. This patch try to aggregation packets in an 16KB
buffer. In this way, totally usb transaction cost will be reduced.
Thoughput test on usb 2.0 show both TCP TX and UPD TX promote ~40M,
from ~240M to ~280M.
This feature is default disabled, and can be enabled by module
parameter, like:
insmod mwifiex.ko aggr_ctrl=1
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
we have observed host system hang when device firmware crash,
stack trace show it was an use-after-free case: previous submitted
urb will be holding in usbcore, and given back to device driver
when device disconnected, while the urb have been freed in usb
device disconnect handler. This patch kill the holding urb before
free its memory.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Usb tx aggregation feature will utilize 4-bytes bus interface header,
otherwise it will be set to zero in default case.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check for ret_val instead of !ret_val to allow the rest of
the code to execute and configure the speed properly.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add RS1 configuration to ixgbe_set_soft_rate_select_speed()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the logic which would previously skip the link configuration
in the case where we are already at the requested speed in
ixgbe_setup_mac_link_multispeed_fiber().
By exiting early we are skipping the link configuration and as such
the driver may not always configure the PHY correctly for SFP+.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the writes are processed immediately. Without the flush it
is possible for operations on one port to spill over the other as the
resource is shared.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous method was unreliable. Use a different register to
differentiate between the SKUs.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Additions to gcc 7 now warn whenever a switch statement falls through
implicitly. This patch adds explicit fall through comments to address the
following warnings:
drivers/net/ethernet/intel/ixgbevf/vf.c: In function ‘ixgbevf_get_reta_locked’:
drivers/net/ethernet/intel/ixgbevf/vf.c:336:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (hw->mac.type < ixgbe_mac_X550_vf)
^
drivers/net/ethernet/intel/ixgbevf/vf.c:338:2: note: here
default:
^~~~~~~
drivers/net/ethernet/intel/ixgbevf/vf.c: In function ‘ixgbevf_get_rss_key_locked’:
drivers/net/ethernet/intel/ixgbevf/vf.c:402:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (hw->mac.type < ixgbe_mac_X550_vf)
^
drivers/net/ethernet/intel/ixgbevf/vf.c:404:2: note: here
default:
^~~~~~~
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following warning is now shown as a result of new checks added for
gcc 7:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function ‘ixgbevf_open’:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1363:13: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size between 3 and 18 [-Wformat-truncation=]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1363:6: note: directive argument in the range [0, 2147483647]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~~~~~~~~~
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1362:4: note: ‘snprintf’ output between 8 and 32 bytes into a destination of size 24
snprintf(q_vector->name, sizeof(q_vector->name) - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-%s-%d", netdev->name, "TxRx", ri++);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Resolve this warning by making a couple of changes.
- Don't reserve space for the null terminator. Since snprintf adds the
null terminator automatically, there is no need for us to reserve a byte
for it.
- Change a couple variables that can never be negative from int to
unsigned int.
While we're making changes to the format string, move the constant strings
into the format string instead of providing them as specifiers.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds/changes fall through comments to address new warnings
produced by gcc 7.
Fixed formatting on a couple of comments in the function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following warning is now shown as a result of new checks added for
gcc 7:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c: In function ‘ixgbe_open’:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:13: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size between 3 and 18 [-Wformat-truncation=]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:6: note: directive argument in the range [0, 2147483647]
"%s-%s-%d", netdev->name, "TxRx", ri++);
^~~~~~~~~~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3117:4: note: ‘snprintf’ output between 8 and 32 bytes into a destination of size 24
snprintf(q_vector->name, sizeof(q_vector->name) - 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-%s-%d", netdev->name, "TxRx", ri++);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Resolve this warning by making a couple of changes.
- Don't reserve space for the null terminator. Since snprintf adds the
null terminator automatically, there is no need for us to reserve a byte
for it.
- Change a couple variables that can never be negative from int to
unsigned int.
While we're making changes to the format string, move the constant strings
into the format string instead of providing them as specifiers.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when setting a VF MAC address there are no error checks to
ensure that the MAC filter was successfully added. This patch adds
additional error checks, reporting, and propagation of errors. It also
will not set the MAC address unless adding the MAC filter was successful.
With these changes, setting the mac address to zeros can no longer call
ixgbe_set_vf_mac() as adding a zero MAC address filter is not valid.
Instead directly delete the filter and, if successful, clear the MAC
address.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The thermal sensor event logic is messed up, because it can execute
the code when there is no thermal event. The current logic is that
it will exit when !capable && !event whereas it really should exit
when !capable || !event. For one thing, it means that the service
task is doing too much work. It probably has some other symptoms as
well. So, correct the logic, simplifying to only execute when there
is a thermal event. The capable check is redundant.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will ensure that VF-to-VF traffic on the same PF
is filtered to allow RSS operation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since FW configures the PHY and MAC X550EM_X has no
PHY access, led_[on|off] is not supported with the 1Gbase-t design.
Removed MAC X550EM_X 1Gbase-t led_[on|off] support by setting
function pointers to NULL and added NULL pointer checks. Also set
init_led_link_act to NULL and added NULL pointer check.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch advertises TSO & GSO features in netdev->mpls_features.
In ixgbe(vf)_tso() where we set up segmentation offload, the IP
header will be the inner network header when eth_p_mpls() indicates
the Ethernet protocol is MPLS (UC or MC).
Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'kzalloc' fails, a NULL pointer will be dereferenced. Return -ENOMEM
instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an i40e_ptp_tx_hang() function similar to the already existing
i40e_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no reason to pass a *vsi pointer if we already have the *pf
pointer in the only location where we call this function. Lets update
the signature and directly pass the *pf data structure pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver uses a bit lock to indicate when a Tx timestamp is in
progress to avoid attempting to timestamp multiple packets at once. This
is required because hardware only has registers to handle one request at
a time.
There is a corner case where we failed to cleanup the bit lock after
a failed transmit. This can potentially result in a state bit being
locked forever.
Add some cleanup code to i40e_xmit_frame_ring to check and make sure we
cleanup incase of these failures. We also modify i40e_tx_map to return
an error code indication DMA failure.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the i40e driver has a limitation on Tx PTP packets.
This requires us to limit the driver to timestamping a single packet at
once. This is done using a state bitlock which enforces that only one
timestamp request is honored at a time.
Unfortunately this suffers from a race condition. The bit lock is not
cleared until after skb_tstamp_tx() is called notifying applications of
a new Tx timestamp. Even a well behaved application sending only one
packet at a time and waiting for a response can wake up and send a new
timestamped packet request before the bit lock is cleared. This results
in needlessly dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
timestamp another packet.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
Now, a well behaved application which has at most one outstanding
timestamp request will not accidentally race with the driver unlock bit.
Obviously an application attempting to timestamp faster than one request
at a time will have some timestamp requests skipped. Unfortunately there
is nothing we can do about that.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40evf hardware doesn't have any way to ever report FCoE enabled
so just force the code to always report FCoE is disabled, remove the
unused defines, and mark the OP as reserved.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a missing line that was missed while merging,
which results in a driver feature in the VF not working to
enable RSS as a negotiated feature.
Fixes: 43a3d9ba34 ("i40evf: Allow PF driver to configure RSS")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes two duplicate lines that snuck into the code somehow.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to write the doorbell if BQL has stopped the queue and
skb->xmit_more is set. Otherwise it is possible for the tx queue to
rot and cause tx timeout.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Suggested-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the existing code, the local variable sh is hardcoded to true to
calculate default rings for shared ring configuration. It is better
to have the caller determine the value of sh.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not write the TX doorbell if skb->xmit_more is set unless the TX
queue is full.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips require the doorbells to be written twice, but newer chips
do not. Add a new common function bnxt_db_write() to write all
doorbells appropriately depending on the chip. Eliminating the extra
doorbell on newer chips has a significant performance improvement
on pktgen.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional chip definitions and macros for all supported chips.
Add a new macro BNXT_CHIP_P4_PLUS for the newer generation of chips and
use the macro to properly determine the features supported by these
newer chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bnxt_en gets a PCI shutdown call, we need to have a new callback
to inform the RDMA driver to do proper shutdown and removal.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new short message format is used on the new BCM57454 VFs. Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel. The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port net device passed to b53_fdb_copy is not used. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is not supported by Chelsio HW when rx_csum is disabled.
Update the netdev features flag when rx_csum is modified.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable FW_OK flag while flashing Firmware. This will help to fix any
potential mailbox timeouts during Firmware flash.
Grab new devlog parameters after Firmware restart. When we FLASH new
Firmware onto an adapter, the new Firmware may have the Firmware Device Log
located at a different memory address or have a different size for it.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark carrier off before registering netdev to ensure that vlan device
picks up the correct state of the carrier
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f8 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Ethernet over UART driver for the
Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to share common functions between QCA7000 SPI and UART protocol
driver the qca_7k_common needs to be a separate kernel module.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately the frame format is not exactly identical between SPI
and UART. In case of SPI there is an additional HW length at the
beginning. So store the initial state to make the decoding state machine
more flexible and easy to extend for UART support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for the upcoming UART driver we need a module
which contains common functions for both interfaces. The module
qca_framing is a good candidate but renaming to qca_7k_common would
make it clear.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this driver is specific to the QCA7000, we should make the module
description more precisely.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function qcaspi_tx_cmd() is only called from qca_spi.c. So we better
move it there.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for an additional MTU define.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid mixing things up, make the MTU and frame length
defines easier to read.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to export qcaspi_netdev_open and qcaspi_netdev_close
because they are also accessible via the net_device_ops.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SET_NETDEV_DEV() in qca_spi to create the "/sys/class/net/<if>/device"
symlink.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the BIT macro for the CONFIG and INT register values.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't make sense to use a signed variable for offset here, so
fix it up.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the includes doesn't reflect the dependencies. So
fix this up by removing all unnecessary entries and add the
necessary ones explicit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for Cortina PHY drivers. Support only CS4340 for now.
The phys are not compatible with IEEE 802.3 clause 22/45 registers.
Implement proper read_status support. The generic 10G phy driver causes
bus register access errors.
The driver should be described using the "ethernet-phy-id" device tree
compatible.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wilson