The struct display_timing is specific to the via subsystem. The naming leads to
collisions with the new struct display_timing, which is supposed to be a shared
struct between different subsystems.
To clean this up, prepend the existing struct with the subsystem it is specific
to.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the modetables used in viafb to
- remove the strange thing that sync_end and blanking_end contained
the length and not the absolute value
- remove hundreds of useless defines
- use fb_videomode and not our own definition so modes defined in
the subsystem and received via EDID are compatible with ours
As the modes are now stored in a flat structure and no longer in a
tree like thing the lookup time was increased but as it is a rare
event anyway it shouldn't matter. Otherwise the behaviour should be
the same as before.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes redundant bits per pixel information by using the
one storged in var directly. Simplifies code without any functional
changes.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
Obviously this is a typo and although there were no effects observed
it's probably better to fix it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch implementes this mode (viafb_SAMM_ON set and
viafb_dual_fb not set) in a useful way for CRT and DVI devices.
The same content is shown on both devices in different video modes.
The first (primary) resolution must not be bigger than the secondary
one and determines the visible region. The same content is shown
centered on the secondary output.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fills xres and yres in var which is required when a
temporary var is genereated when viafb_SAMM_ON is set and
viafb_dual_fb is not set. It also removes an obsolete comment.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch sets the correct polarity for the second adapter when
viafb_SAMM_ON is set and viafb_dual_fb is not set. Just one step to
make this mode useful.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the remaining places where assumptions about the
structure of the modetable were made. Aside from some places where
assumptions are made that certain modes are in the modetable the
only code dealing with the modetable and not just a single mode is
in viamode. This will allow chaniging the modetable and use other
sources for videomodes like the subsystem or EDID.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the need for knowing the modetable structure
within the LCD modesetting function. The magic 60Hz refresh rate was
already there as always the first entry for a resolution was choosen
based on the ascending refresh rate ordering in the modetable.
For all but one this is at least 60Hz, if only higher frequencies
available we choose those like the code before did. The exception is
OLPC but that resolution has only one frequency so we get the same
behaviour there as well.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch splits the hardware initialization out of the modesetting
function which will make it easier to make it conditional and not
require starting from scratch for every mode change, which is
especially annoying in dual framebuffer mode.
This required some minor reordering but it should not influence its
functionality.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch starts to use the information in var for modesetting for
CRT and DVI devices. This is the right thing as it allows us to use
more generic modes than the ones predefined by VIA. We do not yet
allow more generic modes as check_var still limits them to the
predefined ones but with this patch applied it would be really easy
to do so. A problem was VIAs SAMM mode as it has 2 different modes
but just one frame buffer device. This is solved by creating a
pseudo var which contains enough information to use it for
modesetting. Hopefully one day we can use information in var for all
modes that do not involve hardware scaling.
Well I'd like to say that the chance of regressions is low but it is
quite likely that the behaviour in some cases changed especially
when SAMM is involved. I hope we made it better than before in
particular the DVI frequency check was probably broken before and
hopefully works better now.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As there is only one user we can just insert the formula where
needed. Avoids one lookup in the modetable and
viafb_fill_var_timing_info does no longer depend on the modetable.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch introduces 2 new functions for selecting a single mode
based on hres, vres and refresh rate and changes some uses to use
those. The advantage is that it is less error prone than doing the
selection based on refresh rate everywhere and allows replacing the
modetable structure. This includes a little change that users may
notice: If a refresh rate was given as module parameters but does
not exist in the modetable prior to this patch a refresh rate of 60
was assumed and after this patch the closest supported refresh rate
to the one provided by the user is used.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The timing for 640x480-60 was handled different than all others.
This patch changes this by changing the blanking start and end.
The reason for this is that I can't find any reason for the old
behaviour and it was not consistent anyway as the special case for
LCD did not always trigger as the LCD code does not use this
function and it did trigger regardless of whether the display set is
CRT or LCD but only based whether any DVI/LCD device exists.
There are no negative effects observed for CRT or DVI devices.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As the first argument is just part of the structure passed as the
second argument there is no need for it at all.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The locking is done within the viafb_set_*_timing functions so there
is no need to do it here. Move a missing hardware reset into the
modesetting function.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch replaces calls to viafb_load_crtc_timing with the code.
This should make it easier to fix the oddity that in the modetable
the blank and sync end entries contain the length and we need to add
the start values to get those to be written to the hardware.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch replaces the old timing setup code with a redesigned one.
The new code might be slightly faster as it has no conditinals and
does not write the same register multiple times. Also it makes the
comparison to the documentation easier.
Regressions are unlikely but could happen as a lot of hardware is
undocumented.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds a config option to be compatible with X servers like
OpenChrome. This is required as for example the X server does not
handle things like disabled IGAs/PLLs resulting in a potential
freeze on X startup. With this option disabled we can provide some
nice features like power management and not reinitializing the
hardware on every mode switch (taking long time, causing flickering).
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When allowing some PLL calculation we get a frequency that seems to
be a bit higher than what the OLPC DCON likes resulting in a still
readable but not so good image. We don't really know whether this is
a problem with the calculation formula or the OLPC but as other
displays seem to be happy with the other modes adjusting the OLPC
refresh looks like the better thing. This patch prevents a
regression when dynamic PLL calculation is allowed.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the devices connected on OLPC. The OLPC panel seems
to be connected to DVP1 and LVDS2 for some reasons and if not both
are handled correct the display does not work correct or not at all.
This patch prevents regressions on the OLPC where it worked by
accident but would break in future as the driver did not know the
correct devices connected. This might also fix hardware scaling.
Hopefully the OLPC is the only device with such a requirement but it
will be certainly better to actually know what devices are actually
connected and to not work by accident.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes a regression introduced by
fd3cc69848b7e1873e5f12bbcdd572b20277ecf3a
"viafb: remove duplicated clock storage"
caused by an incosistent mode which pretended to have a higher
refresh rate than it actually had. The wrong refresh rate resulted
in a calculated higher pixclock which the OLPC DCON could not handle.
By reducing the refresh rate to 50Hz we get close to the old
pixclock which makes the OLPC display usable again.
Minor other adjustments are needed as 60Hz is assumed to be a safe
value which is not true for OLPC DCON. This is no problem as we only
support 1200x900 on the OLPC.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Reported-by: Daniel Drake <dsd@laptop.org>
This patch moves all unprotected VGA initialization in one table and
provides some documentation for those values.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds support for enabling and configuring the engine on
VIAs IGPs. This is the main clock used for everything but pixel
output.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch introduces dummy functions to execute when we don't know
what we should do (due to missing documentation). They do nothing
but print a nice message in the log explaining the situation.
To trigger this message initial power management support is
activated which might save a bit energy by disabling PLL and clock
if no device is configured to use them.
Note: The message is only shown for the oldest IGPs CLE266 and K400
as for the other platforms there are reasonable assumptions
how it does (hopefully) work.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch is a huge move operation with some rename and introduces
an interface to still use the functions. This should be a step in
the right direction to reuse the code whenever possible but cleanly
separate code that differs on different platform and keeping the
complexity as low as possible.
pll_config was renamed to via_pll_config to keep the naming scheme.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds functions to enable/disable the display clocks.
It also fixes a tiny bug that slipped in with a previous commit but
could not yet have caused any problems.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds some support for clock source selection as well as
PLL power management. The code is unused at the moment but was
successfully tested as far as possible.
The implementation is according to the documentation for VX700,
VX800, VX855, VX900. Probably the source selection works like this
starting with K800 and the power managemennt at least since VX700.
(guessed based on the initialization in viamode.c)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As no caller is interested in the result call viafb_get_clk_value
directly from viafb_set_vclock to encapsulate the hardware dependend
stuff there.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch allows calculating the pll multiplier within limits based
on the previous table. All available information supports that it
should be possible/sane to choose the multiplier free within some
ranges.
Storing the multiplier ranges instead of lots of pll configurations
reduces the memory needed and may as well improve the performance.
It is also expected to provide better pll values resulting in better
frequencies for the connected devices.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As the iga path is the only remaining information which is also
handled by the active devices there is no reason to keep it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Later the correct values will be written so there is no need to
write early some values which might be wrong.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This moves some mode independend initialization code to the function
where the other parts of the initialization are.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes multiple issues with the handling of refresh rates
especially for multi-display setups. If you experienced problems
with wrong refresh rates this patch might fix them.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch splits the pll configs up on pll versions. This allows
easy adding of other known good pll values. Additionally it made it
possible to remove invalid configurations resulting in better
behaviour for such cases. The resulting clocks are no longer stored
resulting in some computing overhead on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The clocks can be easily recalculated by the timing and refresh value.
This brings us one step closer to removing VIAs modetable and use
generic ones and being easier extensible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Before this patch only clocks that perfectly match were used and if
none existed this was not handled properly. This patch changes this
to always use the closest clock supported. This should behave like
before for clocks that have a perfect match but be much saner for
clocks which are slightly off.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the direct lookup table for resolution+refresh and
pixclock by calculating this information from the mode table. Removes a
lot of dupllication and error potential by just doing a little more
calculations on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
These parameters are the same for all currently known VIA IGPs so it
does not make any sense to store them with IGP specific data. This
saves a few bytes and helps a bit in dicovering the real differences.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes some write-only variables from the device management
structures. Just a small cleanup.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Many local variables should be declared static.
Found by sparse, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Steffen Trumtrar