CAN interfaces only support MTU values of 16 (CAN 2.0) and 72 (CAN FD).
Setting the MTU to other values is pointless but it does not really hurt.
With the introduction of the CAN FD support in drivers/net/can a new
function to switch the MTU for CAN FD has been introduced.
This patch makes use of this can_change_mtu() function to check for correct
MTU settings also in legacy CAN (2.0) devices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple failure paths where urb leaks.
Is spare code within ems_usb_start_xmit(),
usb_free_urb() should be used to deallocate urb instead of usb_unanchor_urb().
In ems_usb_start() there is no usb_free_urb() if usb_submit_urb() fails.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable open_time in the struct ems_usb was used to protect
ems_usb_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Do not return from ems_usb_start if allocation fails. If not all URBs
could be allocated use the one already submitted.
Signed-off-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netif_device_attched is called twice when ems_usb_start fails with -ENODEV
Signed-off-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This converts the drivers in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Yoann DI-RUZZA <y.diruzza@lim.eu>
Cc: George <george0505@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...
This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"skb" is alway non-null here, but even if it were null the check isn't
needed because dev_kfree_skb() can handle it.
This eliminates a smatch warning about dereferencing a variable before
checking that it is non-null.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds error checking of ctrlmode values for CAN devices. As
an example all availabe bits are implemented in the mcp251x driver.
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent the CAN drivers to operate on invalid socketbuffers the skbs are
now checked and silently dropped at the xmit-function consistently.
Also the netdev stats are consistently using the CAN data length code (dlc)
for [rx|tx]_bytes now.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A valid CAN dataframe can have a data length code (DLC) of 0 .. 8 data bytes.
When reading the CAN controllers register the 4-bit value may contain values
from 0 .. 15 which may exceed the reserved space in the socket buffer!
The ISO 11898-1 Chapter 8.4.2.3 (DLC field) says that register values > 8
should be reduced to 8 without any error reporting or frame drop.
This patch introduces a new helper macro to cast a given 4-bit data length
code (dlc) to __u8 and ensure the DLC value to be max. 8 bytes.
The different handlings in the rx path of the CAN netdevice drivers are fixed.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the private functions alloc_can_skb() and
alloc_can_err_skb() of the at91_can driver public and adapts all
drivers to use these. While making the patch I realized, that
the skb's are *not* setup consistently. It's now done as shown
below:
skb->protocol = htons(ETH_P_CAN);
skb->pkt_type = PACKET_BROADCAST;
skb->ip_summed = CHECKSUM_UNNECESSARY;
*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
memset(*cf, 0, sizeof(struct can_frame));
The frame is zeroed out to avoid uninitialized data to be passed to
user space. Some drivers or library code did not set "pkt_type" or
"ip_summed". Also, "__constant_htons()" should not be used for
runtime invocations, as pointed out by David Miller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com).
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp