Most Serial Flash chips support 24bit addressing as a default but more
recent incarnations can support 32bit. Based on information provided
though platform specific data and capabilities we can determine whether
or not our current chip can. This patch provides a means to setup the
FSM message sequence to put the chip into 32bit mode.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Based on information we can obtain though platform specific data and/or
chip capabilities we are able to determine whether or not we can handle
a SoC reset or not. To find out why this is important please read the
comment provided in the patch.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Firstly we search for our preference read/write configuration based on a
given chip's capabilities. Then we actually set up the message sequence
accordingly.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for setting 32bit addressing
mode on the Flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for erasing a single sector.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's important for us to determine which device was used to boot from in
order to make some correct decisions surrounding Power Management. On
each of the platforms which support the FSM this is communicated via
a set of mode pins held in the system configuration area. This patch
determine the boot device and stores the result.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare read/write FSM message sequence(s) based on chip capability
and configuration.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Take some known parameters, namely size and number of sectors and use
them to determine weather a device can support 32bit addressing or not.
If it can, set the associated flash capability flag for latter use.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide a means to traverse though all supplied FSM message
sequence configurations and pick one based on our chip's capabilities.
The first one we match will be the preferred one, as they are
presented in order of preference.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using previously added infrastructure we can now extract a device's JEDEC
ID, compare it to a list of known and supported devices and make assumptions
based on known characteristics of a given chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Supply a lookup table of all the devices we intend to support. This table
is used to store device information such as; a human readable device name,
their JEDEC ID (plus the extended version), sector size and amount, a bit
store of a device's capabilities, its maximum running frequency and
possible use of a per-device configuration call-back.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
JEDEC have helped to standardise a great deal of the commands which
can be issued to a Serial Flash devices. Many of the Serial Flash
Discoverable Parameters (SFDP) commands are generic across devices.
This patch provides a shared point where these commands can be
defined.
Suggested-by: Mark Brown <broonie@kernel.org>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Once we start supporting devices it will be handy go detect them
dynamically. This will be done using the chip's unique JEDEC ID. This
patch allows us to extract a device's JEDEC ID using the a predefined
FSM register write sequence.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When invoked the driver will attempt to read any available data from
the FSM's data register. Any data collected from this FIFO would have
originated from the flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM hardware works by setting a predetermined sequence of register
writes. Rather than open coding them inside each functional block we're
going to define them in a series of formatted 'sequence structures'.
This patch provides the framework which shall be used for every action.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch uses default values to initialise a connected flash chip. This
includes; a device soft reset, setting of a safe working frequency, a
switch into Fast Sequencing Mode, configuring of timing data and a purge
of the FIFO.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide the FSM's register addresses, register bit names/offsets
and some commands which will prove useful as we start bulk the FMS's
driver out with functionality.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is a new driver. It's used to communicate with a special type of
optimised Serial Flash Controller called the FSM. The FSM uses a subset
of the SPI protocol to communicate with supported NOR-Flash devices.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a write to one time programmable memory (OTP) hits the end of this
memory area, no more data can be written. The count variable in
mtdchar_write() in drivers/mtd/mtdchar.c is not decreased anymore.
We are trapped in the loop forever, mtdchar_write() will never return
in this case.
The desired behavior of a write in such a case is described in [1]:
- Try to write as much data as possible, truncate the write to fit into
the available memory and return the number of bytes that actually
have been written.
- If no data could be written at all, return -ENOSPC.
This patch fixes the behavior of OTP write if there is not enough space
for all data:
1) mtd_write_user_prot_reg() in drivers/mtd/mtdcore.c is modified to
return -ENOSPC if no data could be written at all.
2) mtdchar_write() is modified to handle -ENOSPC correctly. Exit if a
write returned -ENOSPC and yield the correct return value, either
then number of bytes that could be written, or -ENOSPC, if no data
could be written at all.
Furthermore the patch harmonizes the behavior of the OTP memory write
in drivers/mtd/devices/mtd_dataflash.c with the other implementations
and the requirements from [1]. Instead of returning -EINVAL if the data
does not fit into the OTP memory, we try to write as much data as
possible/truncate the write.
[1] http://pubs.opengroup.org/onlinepubs/9699919799/functions/write.html
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
fixme applied : check device size is a multiple of erasesize.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ELM driver incorrectly reagard any non-zero return value from
pm_runtime_get_sync as an error, but it may return 1 if the device
was already active. Fix to only error when return value is negative.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mutex_destroy added on each device in block2mtd_exit and add_device failure
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit b2a2a84d35 (mtd: phram: dot not crash when
built-in and passing boot param) claims to be "based on Ville Herva's similar
patch to block2mtd" (c4e7fb3137), but it has
missed the crucial point of the original path: all these "if(n)def MODULE".
It has broken the possibility to create several phram instances when phram is
compiled as module. The possibility to add instances via /sys writes to
/sys/module/phram/parameters/phram was also broken with mentioned patch.
Proposed patch takes the idea of original block2mtd patch to its full extent.
Assumption "This function is always called before 'init_phram()'" was also
incorrect, so removed the comment. This patch effectively reverts also
b11ec57fc6 (mtd: phram: fix section mismatch for
phram_setup).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[Brian: remove static assigment = 0]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Spansion s25fl256s1 and s25fl512s support Dual SPI transfers, hence set the
M25P80_DUAL_READ flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.
While an earlier version of commit 3487a63955
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtdram_init_device() wasn't updated along with mtd_partition.name.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
In the following commit (in -next):
commit 8552b439ab
drivers: mtd: m25p80: convert "bool" read check into an enum
We converted the boolean 'fast_read' property to become an enum
'flash_read', but at the same time, we changed the conditional path so
that it doesn't choose a default value in some cases (technically, we
choose the correct default simply by virtue of devm_kzalloc(), which
zeroes this out to be a NORMAL read operation, but still...).
Fix this by setting a default for the 'else' clause.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
commit 3487a63955 ("drivers: mtd: m25p80: add
quad read support") in -next added both the 3-byte OPCODE_QUAD_READ and the
4-byte OPCODE_QUAD_READ_4B, but incorrectly uses OPCODE_QUAD_READ for both
3-byte and 4-byte addressing.
Use OPCODE_QUAD_READ_4B in the 4-byte case to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Micron m25px16 spi flash chip.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some flash also support quad read mode. Adding support for quad read
mode in m25p80 for Spansion and Macronix flash.
[Tweaked by Brian]
With this patch, quad-read support will override fast-read and
normal-read, if the SPI controller and flash chip both support it.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is a cleanup prior to adding quad read support. This will facilitate
easy addition of more read commands check under an enum rather that defining a
separate bool for it.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Ensure that the error message if we identify a flash we don't know how to
talk to is displayed on the console in order to aid diagnostics. While
we're at convert the message to use dev_info() rather than our hand rolled
version of it for consistency.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Device removal should fail if MTD unregistration fails.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
A new 32Mbit SPI NOR flash from Macronix. Nothing special.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
It seems like the following commit was never necessary
commit 5f94913795
Author: Shaohui Xie <Shaohui.Xie@freescale.com>
Date: Fri Oct 14 15:49:00 2011 +0800
mtd: m25p80: don't probe device which has status of 'disabled'
because it duplicates the code in of_platform_device_create_pdata()
which ensures that 'disabled' nodes are never instantiated.
Also, drop the __maybe_unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: <devicetree@vger.kernel.org>
Remove the compile-time option for FAST_READ, since we have run-time
support for detecting it. This refactors the logic for enabling
fast-read, such that for DT-enabled devices, we honor the
"m25p,fast-read" property but for non-DT devices, we default to using
FAST_READ whenever the flash device supports it.
Normal READ and FAST_READ differ only in the following:
* FAST_READ supports SPI higher clock frequencies [1]
* number of dummy cycles; FAST_READ requires 8 dummy cycles (whereas
READ requires 0) to allow the flash sufficient setup time, even when
running at higher clock speeds
Thus, for flash chips which support FAST_READ, there is otherwise no
limiting reason why we cannot use the FAST_READ opcode instead of READ.
It simply allows the SPI controller to run at higher clock rates. So
theoretically, nobody should be needing the compile-time option anyway.
[1] I have a Spansion S25FL128S datasheet which says:
"The maximum operating clock frequency for the READ command is 50
MHz."
And:
"The maximum operating clock frequency for FAST READ command is 133
MHz."
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FIXME and NOTE have already been fixed (we have FAST_READ support).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch fixes two memory errors:
1. During a probe failure (in mtd_device_parse_register?) the command
buffer would not be freed.
2. The command buffer's size is determined based on the 'fast_read'
boolean, but the assignment of fast_read is made after this
allocation. Thus, the buffer may be allocated "too small".
To fix the first, just switch to the devres version of kzalloc.
To fix the second, increase MAX_CMD_SIZE unconditionally. It's not worth
saving a byte to fiddle around with the conditions here.
This problem was reported by Yuhang Wang a while back.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Yuhang Wang <wangyuhang2014@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Cc: <stable@vger.kernel.org>
This patch moves the char and block major number definitions
to major.h to be with the rest of the major numbers.
While doing this, include major.h in the files that need it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron N25Q512A is a spi flash memory with following features:
-64MB size, 1.8V, Mulitple I/O, 4KB Sector erase memory.
-Memory is organised as 1024(64KB) main sectors.
-Each sector is divided into 256 pages.
-Register set/Opcodes are similar to other N25Q family products.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use free_bch() instead of kfree() to free init_bch()
allocated data.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
devm_kzalloc is device managed and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Driver core will set the driver data to NULL upon detach
or probe failure.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
phram was 32-bit limited by design. Machines are growing up, but phram
module is still useful. Update it. The patch is bigger than minimum,
because simple_strtoul() is obsolete.
Tested on MIPS64 and compile-tested for PPC (32 bit).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Reviewed-by: Joern Engel <joern@logfs.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This flashchip is used in D-Link DIR-610 A1 router board
and maybe several others, yet is not kernel upstream.
So add support for it according to datasheet [0], making it easier
to support other boards using this flashchip in the future.
[0] http://www.esmt.com.tw/DB/manager/upload/F25L32PA.pdf
Signed-off-by: Flavio Silveira <fggs@terra.com.br>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
struct dataflash's 'partition' field is unused. Just remove it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
According to the datasheet for Micron n25q256a (N25Q256A13ESF40F) 4-byte
addressing mode should be entered as follows:
<quote>
To enter or exit the 4-byte address mode, the WRITE ENABLE command
must be executed to set the write enable latch bit to 1. (Note: The
WRITE ENABLE command must NOT be executed on the N25Q256A83ESF40x and
N25Q256A83E1240x devices.) S# must be driven LOW. The effect of the
command is immediate; after the command has been executed, the write
enable latch bit is cleared to 0.
</quote>
Micron's portable way to perform this for all types of Micron flash
is to first issue a write enable, then switch the addressing mode
followed by a write disable to avoid leaving the flash in a write-
able state.
Signed-off-by: Elie De Brauwer <eliedebrauwer@email.com>
[Brian: reworked a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for PMC (now Chingis, part of ISSI) Pm25LV512 (512 Kib),
Pm25LV010 (1 Mib) and Pm25LQ032 (32 Mib) SPI Flash chips.
This patch addresses two generations of PMC SPI Flash chips:
- Pm25LV512 and Pm25LV010: these have 4KiB sectors and 32KiB
blocks. The 4KiB sector erase uses a non-standard opcode
(0xd7). They do not support JEDEC RDID (0x9f), and so they can only
be detected by matching their name string with pre-configured
platform data. Because of the cascaded acquisitions, the datasheet
is no longer available on the current manufacturer's website,
although it is still commonly used in some recent wireless routers
(<https://forum.openwrt.org/viewtopic.php?pid=186360#p186360>). The
only public datasheet available seems to be on GeoCities:
<http://www.geocities.jp/scottle556/pdf/Pm25LV512-010.pdf>
- Pm25LQ032: a newer generation flash, with 4KiB sectors and 64KiB
blocks. It uses the standard erase and JEDEC read-ID
opcodes. Manufacturer's datasheet is here:
<http://www.chingistek.com/img/Product_Files/Pm25LQ032C%20datasheet%20v1.6.1.pdf>
This patch is resent in order to take into account both Brian Norris
remarks and this upstream patch:
commit e534ee4f9c
Author: Krzysztof Mazur <krzysiek@podlesie.net>
Date: Fri Feb 22 15:51:05 2013 +0100
mtd: m25p80: introduce SST_WRITE flag for SST byte programming
Not all SST devices implement the SST byte programming command.
Some devices (like SST25VF064C) implement only standard m25p80 page
write command.
Now SPI flash devices that need sst_write() are explicitly marked
with new SST_WRITE flag and the decision to use sst_write() is based
on this flag instead of manufacturer id.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
[Brian: fixed conflict]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested with BCM4706.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
convert to module_platform_driver instead of init/exit
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Libo chen <libo.chen@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd is just member of bcm47xxsflash, so we should free bcm47xxsflash not
its member. So I use devm_kazlloc instead of kazlloc to avoid it.
* Changelog:
convert to devm_kzalloc
Signed-off-by: Libo chen <libo.chen@huawei.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[Brian: fixed conflicts]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds support for the Everspin mr25h10 MRAM chip to the m25p80
driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a flag to struct flash_info indicating that
fast_read is not supported. This now gives the following logic
when determing whether to enable fastread:
If the flash chip does not support fast_read, then disable it.
Otherwise:
1) enable fast_read if device node contains m25p,fast-read
2) enable fast_read if forced in Kconfig
This makes enabling CONFIG_M25PXX_USE_FAST_READ a safe option
since we no longer enable the fast_read option unconditionally.
For now fast_read is disabled for the everspin mr25h256 and the
catalyst devices. Others may need the flag aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flags may have to be overwritten, so add them to the CAT25_INFO
macro.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_property_read_bool properly compiles away, no need to ifdef this
for non DT builds.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For SPI NOR flash that are larger than 128Mbit (16MiB), we need 4 bytes
of address space to reach the entire flash; however, the original SPI
flash protocol used only 3 bytes for the address. So far, the practice
for handling this has been either to use new command opcodes that are
defined to use 4 bytes for their address, or to use special
mode-switching command to configure all traditionally-3-byte-address
commands to take 4 bytes instead.
Macronix and Spansion developed two incompatible methods for
entering/exiting "4-byte address mode." Micron flash uses the Macronix
method (OPCODE_{EN4B,EX4B}), not the Spansion method.
This patch solves addressing issues on Micron n25q256a and provides the
ability to support other future Micron SPI flash >16MiB.
Quoting a Micron representative:
"Majority of our NOR that needs 4-byte addressing (256Mb or 32MB and
higher) enter and exit 4byte through B7h and E9h commands. The
N25Q256A7xxx and N25Q512A7xxx parts do not support 4-byte addressing
mode via B7h or E9h command."
They further clarified that those that don't support the enter/exit
opcodes (B7h/E9h) are manufactured specifically to come up by default in
4-byte mode. We don't need to treat those parts any diffently, as they
will discard the EN4B opcode as a no-op.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch proposes to remove kernel configuration parameters
defined in drivers/mtd/devices/Kconfig, but used nowhere
in the makefiles and source code (except in comments).
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ELM is used for locating bit-flip errors in when using BCH ECC scheme.
This patch adds suspend/resume support for leaf level ELM driver,
And also provides ELM register context save & restore support, so that
configurations are preserved across hardware power-off/on transitions.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use a more current logging style.
Convert homegrown ERROR/INFO macros to pr_<level>.
Convert homegrown parse_err macros to pr_err and
expand hidden flow control.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Added a 16MiB winbond devce to the device list
erase size = 64KiB and number of blocks = 256.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Traditionally, the command set used by SPI flash only supported a 3-byte
address. However, large SPI flash (>= 32MiB, or 256Mib) require 4 bytes
to address the entire flash. Most manufacturers have supplied a mode
switch (via a "bank register writer", or a "enable 4-byte mode"
command), which tells the flash to expect 4 address cycles from now on,
instead of 3. This mode remains until power is cut, the reset line is
triggered (on packages where present), or a command is sent to reset the
flash or to reset the 3-byte addressing mode.
As an alternative, some flash manufacturers have developed a new command
set that accept a full 4-byte address. They can be used orthogonally to
any of the modes; that is, they can be used when the flash is in either
3-byte or 4-byte address mode.
Now, there are a number of reasons why the "stateful" 4-byte address
mode switch may not be acceptable. For instance, some SoC's perform a
dumb boot sequence in which they only send 3-byte read commands to the
flash. However, if an unexpected reset occurs, the flash chip cannot be
guaranteed to return to its 3-byte mode. Thus, the SoC controller and
flash will not understand each other. (One might consider hooking up the
aforementioned reset pin to the system reset line so that any system
reset will reset the flash to 3-byte mode, but some packages do not
provide this pin. And in some other packages, one must choose between
having a reset pin and having enough pins for 4-output QSPI support.
It is an error prone process choosing a flash that will support a
hardware reset pin!)
This patch provides support for the new stateless command set, so that
we can avoid the problems that come with a stateful addressing mode
change. The flash can be left in "3-byte mode" while still accessing the
entire flash.
Note that Spansion supports this command set on all its large flash
(e.g, S25FL512S), and Macronix has begun supporting this command set on
some new flash (e.g., MX25L25635F). For the moment, I don't know how to
differentiate the Macronix that don't support this command set (e.g.,
MX25L25635E) from those that do, so this patch only supports Spansion.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all users of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled. Also, unnecessary CONFIG_PM ifdefs
are removed
drivers/mtd/devices/spear_smi.c:1049:12: warning: 'spear_smi_suspend' defined but not used [-Wunused-function]
drivers/mtd/devices/spear_smi.c:1059:12: warning: 'spear_smi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
They are needed for erasing/writing. Use a magic pointers and small
functions to prepare code for adding other buses support in the future
(like SSB).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD subsystem has historically tried to be as configurable as possible. The
side-effect of this is that its configuration menu is rather large, and we are
gradually shrinking it. For example, we recently merged partitions support with
the mtdcore.
This patch does the next step - it merges the mtdchar module to mtdcore. And in
this case this is not only about eliminating too fine-grained separation and
simplifying the configuration menu. This is also about eliminating seemingly
useless kernel module.
Indeed, mtdchar is a module that allows user-space making use of MTD devices
via /dev/mtd* character devices. If users do not enable it, they simply cannot
use MTD devices at all. They cannot read or write the flash contents. Is it a
sane and useful setup? I believe not. And everyone just enables mtdchar.
Having mtdchar separate is also a little bit harmful. People sometimes miss the
fact that they need to enable an additional configuration option to have
user-space MTD interfaces, and then they wonder why on earth the kernel does
not allow using the flash? They spend time asking around.
Thus, let's just get rid of this module and make it part of mtd core.
Note, mtdchar had additional configuration option to enable OTP interfaces,
which are present on some flashes. I removed that option as well - it saves a
really tiny amount space.
[dwmw2: Strictly speaking, you can mount file systems on MTD devices just
fine without the mtdchar (or mtdblock) devices; you just can't do
other manipulations directly on the underlying device. But still I
agree that it makes sense to make this unconditional. And Yay! we
get to kill off an instance of checking CONFIG_foo_MODULE, which is
an abomination that should never happen.]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We need them to add erase/write support. This may duplicate some defines
with bcma and/or ssb code, but it makes more sense to keep that in
bcm47xxsflash which is supposed to work with both buses.
Duplicated defines will be removed from ssb/bcma.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's going to be needed for erase and write operations, they differ
between Atmel and ST flashes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To implement erase and write support we need to "talk" with ChipCommon
BCMA core which serial flash it attached to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Be a bit stricter and add few more 'const' qualifiers.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In case the driver is not probed - due to config mismatches or errors
in the DTS files - dev_get_drvdata() returns NULL, leading to an Ooops
during boot.
Make elm_config() return an error in such cases to propagate the error
up to the user, so it can fall back to software mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This device was reported over a year ago on OpenWrt mailing list in the
thread [OpenWrt-Devel] RedBoot partition table with winbond m25q128vb
(unfortunately, I can't find message id). Macpaul seemed to have
problems with partition driver, but it seems the device was working OK.
Reported-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all SST devices implement the SST byte programming command.
Some devices (like SST25VF064C) implement only standard m25p80 page
write command.
Now SPI flash devices that need sst_write() are explicitly marked
with new SST_WRITE flag and the decision to use sst_write() is based
on this flag instead of manufacturer id.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Lee Jones