fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts b01af4579e.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71c6c837 (drivers/net: fix tasklet misuse issue) introduced a
build failure in the xilinx driver. axienet_dma_err_handler isn't
declared before its use in axienet_open.
This patch provides the prototype before axienet_open.
Cc: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use &port->netdev->dev instead of NULL since dma_pool_create() doesn't
allow NULL dev.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this udev doesn't have a way to key the ne device to the platform
device.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leftover of 57d6d456cf ("sis900: stop
using net_device.{base_addr, irq} and convert to __iomem.").
It is needed for suspend / resume to work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jan Janssen <medhefgo@web.de>
Cc: Daniele Venzano <venza@brownhat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply makes the tilegx net driver call request_irq with a
non-null name. It makes the output in /proc/interrupts more obvious, but
also helps tools that don't expect to find null there.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.
For example:
~# ifconfig eth0 down
~# echo disk > /sys/power/state
<trigger a restore from hibernation>
~# ifconfig eth0 up
SIOCSIFFLAGS: No such device
This happens because the restore function bails out early upon
finding devices that were not up at hibernation. In doing so,
it never gets to the netif_device_attach call at the end of
the restore function. Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INGPADBOUNDARY_MASK is already shifted. No need to shift it again. On reloading
a driver it was resulting in a bad SGE FL MTU sizes [1536, 9088] error. This
only causes an issue on systems that have L1 cache size of 32B, 128B, 512B,
2048B or 4096B.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004
Probable regression from d4ed95d796e5126bba51466dc07e287cebc8bd19;
more chipsets are likely affected.
Tested on top of a 3.2.23 kernel.
Reported-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit b27393aecf
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance. Also adopt use of skb_frag_size() accessor.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: David S. Miller <davem@davemloft.net>
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Uri Habusha <urih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a 36 bit dtb file, the driver complains "resource busy".
Investigating the source of the message leads one to the
gianfar_ptp_probe function.
Since the type of the device resource requested in this function
is IORESOURCE_MEM, it should use "iomem_resource" instead of
"ioports_resource".
Signed-off-by: Wei Yang <Wei.Yang@windriver.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw/davinci mdio ip cores are present on am33xx, so make NET_VENDOR_TI
visible for it as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the resource cleanup to act correctly and prevent a kernel oops when
mlx4_QUERY_ADAPTER() fails.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These debug prints left behind by commits c82e9aa0a8 ("mlx4_core:
resource tracking for HCA resources used by guests"), 54679e1482
("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache
for smp_snoop") and 993c401e20 ("mlx4_core: Add IB port-state
machine and port mgmt event propagation") make it pretty hard to
actually use the mlx4_core debug messages when running in SRIOV/IB
mode -- for example, the module load sequence of a device with one VF
yielded 631 debug prints, with 408 of them being from this set. Let's
just remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before use the request and response queue addr, make sure it has wrote
to the registers.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also fixes the build failure caused due to removal of #ifdef
CONFIG_CHELSIO_T4_OFFLOAD condition
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a3348722 AFEX FCoE function is continuously reset.
The patch prevents the resetting and removes debug print
to stop garbaging syslog.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).
http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.
Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.
Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled. Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.
Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.
To avoid possible Tx stalls, change WTHRESH back to 1.
The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.
please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3bc1
Author: Tom Herbert <therbert@google.com>
Date: Mon Nov 28 16:33:16 2011 +0000
e1000e: Support for byte queue limits
Changes to e1000e to use byte queue limits.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain platforms, BE hardware could falsely indicate UE.
For BE family of NICs, do not set hw_error based on the UE bits.
If there was a real fatal error, the corresponding h/w block will
automatically go offline and stop traffic.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported a kernel build failure as following:
drivers/built-in.o: In function `pch_gbe_ioctl':
pch_gbe_main.c:(.text+0x510370): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x510393): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x5103b3): undefined reference to `pch_ch_control_write'
...
It's a regression by commit da1586461. The root cause is that
the CONFIG_PPS is not set there, consequently CONFIG_PTP_1588_CLOCK
can not be set anyway, which finally causes ptp_pch and pch_gbe_main
build failures.
As David prefers to use *select* to fix such module co-dependency issues,
this patch explicitly selects all the possible dependencies of PCH_PTP.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Haicheng Li <haicheng.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pulled mainline in order to get the UAPI infrastructure already
merged before I pull in David Howells's UAPI trees for networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support of those devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ariel Elior