Putting an empty 'mlx5_flow_spec' structure on the stack is a bit
wasteful and causes a warning on 32-bit architectures when building
with clang -fsanitize-coverage:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c: In function 'mlx5_eswitch_termtbl_create':
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_termtbl.c:90:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Since the structure is never written to, we can statically allocate
it to avoid the stack usage. To be on the safe side, mark all
subsequent function arguments that we pass it into as 'const'
as well.
Fixes: 10caabdaad ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Misc updates from mlx5-next branch:
1) E-Switch vport metadata support for source vport matching
2) Convert mkey_table to XArray
3) Shared IRQs and to use single IRQ for all async EQs
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In vport metadata matching, source port number is replaced by metadata.
While FW has no idea about what it is in the metadata, a syndrome will
happen. Specify a known origin to avoid the syndrome.
However, there is no functional change because ANY_VPORT (0) is filled
in flow_source, the same default value as before, as a pre-step towards
metadata matching for fast path.
There are two other values can be filled in flow_source. When setting
0x1, packet matching this rule is from uplink, while 0x2 is for packet
from other local vports.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a dual-port VHCA sends a RoCE packet on its non-native port, and the
packet arrives to its affiliated vport FDB, a mismatch might occur on the
rules that match the packet source vport as it is not represented by single
VHCA only in this case. So we change to match on metadata instead of source
vport.
To do that, a rule is created in all vports and uplink ingress ACLs, to
save the source vport number and vhca id in the packet's metadata in order
to match on it later.
The metadata register used is the first of the 32-bit type C registers. It
can be used for matching and header modify operations. The higher 16 bits
of this register are for vhca id, and the lower 16 ones is for vport
number.
This change is not for dual-port RoCE only. If HW and FW allow, the vport
metadata matching is enabled by default.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the flow data structures, add new flow_context and move
flow_tag into it, as flow_tag doesn't belong to the rule action.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a dual-port VHCA sends a RoCE packet on its non-native port, and
the packet arrives to its affiliated vport FDB, a mismatch might occur
on the rules that match the packet source vport. So we replace the
match on source port with the match on metadata that was configured in
ingress ACL, and that metadata will be passed further also to the NIC
RX table of the eswitch manager.
Introduce vport metadata matching bits and enum constants as a pre-step
towards metadata matching.
o metadata type C registers in the misc parameters 2 fields.
o esw_uplink_ingress_acl bit in esw cap. If it set, the device supports
ingress ACL for the uplink vport.
o fdb_to_vport_reg_* bits in flow table cap and esw vport context, to
support propagating the metadata to the nic rx through the loopback
path.
o flow_source in flow context, to indicate the known origin of packets.
o enum constants, to support the above bits.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The lock protecting the data structure does not need to be an rwlock. The
only read access to the lock is in an error path, and if that's limiting
your scalability, you have bigger performance problems.
Eliminate mlx5_mkey_table in favour of using the xarray directly.
reg_mr_callback must use GFP_ATOMIC for allocating XArray nodes as it may
be called in interrupt context.
This also fixes a minor bug where SRCU locking was being used on the radix
tree read side, when RCU was needed too.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add API to get the current Eswitch encap mode.
It will be used in downstream patches to check if
flow table can be created with encap support or not.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Report devlink health on FW fatal issues via fw_fatal_reporter. The
driver recover flow for FW fatal error is now being handled by the
devlink health.
Having the recovery controlled by devlink health, the user has the
ability to cancel the auto-recovery for debug session and run it
manually.
Call mlx5_enter_error_state() before calling devlink_health_report() to
ensure entering device error state even if auto-recovery is off.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Create mlx5_devlink_health_reporter for fw fatal reporter.
The fw fatal reporter is added in addition to the fw reporter and
implements the recover callback.
The point of having two reporters for FW issues, is that we
don't want to run FW recover on any issue, but only fatal ones.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use devlink_health_report() to report any symptom of FW issue as FW
counter miss or new health syndrome.
The FW issues detected in mlx5 during poll_health which is called in
timer atomic context and so health work queue is used to schedule the
reports.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Create mlx5_devlink_health_reporter for FW reporter. The FW reporter
implements devlink_health_reporter diagnose callback.
The fw reporter diagnose command can be triggered any time by the user
to check current fw status.
In healthy status, it will return clear syndrome. Otherwise it will
return the syndrome and description of the error type.
Command example and output on healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 0
Command example and output on non healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 8 Description: unrecoverable hardware error
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New mlx5 adapters allow the driver to reset the FW in the event of an
error, this action called "SW Reset". When an SW reset is issued on any
PF all PFs enter reset state which is a recoverable condition. The
existing recovery flow was designed to allow the recovery of a VF after
a PF driver reload. This patch adds the sw reset to the NIC states
as a preparation for sw reset handling.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to 7 while the reset is in progress.
2. Once the reset completes the NIC interface mode is set to 1.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Crdump allows the driver to retrieve a dump of the FW PCI crspace.
This is useful in case of catastrophic issues which may require FW
reset. The crspace dump can be used for later debug.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The Vendor Specific Capability (VSC) is used to activate a gateway
interfacing with the device. The gateway is used to read or write
device configurations, which are organized in different domains (spaces).
A configuration access may result in multiple actions, reads, writes.
Example usages are accessing the Crspace domain to read the crspace or
locking a device semaphore using the Semaphore domain.
The configuration access use pci_cfg_access to prevent parallel access to
the VSC space by the driver and userspace calls.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously, EQ joined the chain notifier on creation.
This forced the caller to be ready to handle events before creating
the EQ through eq_create_generic interface.
To help the caller control when the created EQ will be attached to the
IRQ, add enable/disable API.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The patch modifies the IRQ allocation so that all async EQs are
assigned to the same IRQ resulting in more available IRQs for
completion EQs.
The changes are using the support for IRQ sharing and EQ polling budget
that was introduced in previous patches so when the shared interrupt is
triggered, the kernel will serially call the handler of each of the
sharing EQs with a certain budget of EQEs to poll in order to prevent
starvation.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
IRQ table should only exist for mlx5_core_dev for PF and VF only.
EQ table of mediated devices should hold a pointer to the IRQ table
of the parent PCI device.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of requesting IRQ with eq creation, IRQs will be requested
before EQ table creation.
Instead of freeing the IRQs after EQ destroy, free IRQs after eq
table destroy.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Multiple EQs may share the same IRQ in subsequent patches.
Instead of calling the IRQ handler directly, the EQ will register
to an atomic chain notfier.
The Linux built-in shared IRQ is not used because it forces the caller
to disable the IRQ and clear affinity before free_irq() can be called.
This patch is the first step in the separation of IRQ and EQ logic.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For ECPF with eswitch manager privilege, query the host max VF count
by querying the device using query_functions command.
With this enhancement:
1. flow steering entries are created only for valid vports based on
the max VF count of the PF.
2. Driver only queries cap of valid vport.
Eswitch requires the max VFs when doing initialization, so do sr-iov
init before eswitch init.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use Geneve TLV Options object to manage the flex parser matching
on the 32-bit options data.
When the first flow with a certain class/type values is requested to
be offloaded, create a FW object with FW command (Geneve TLV Options
general object) and start counting the number of flows using this object.
During this time, any request with a different class/type values will
fail to be offloaded.
Once the refcount reaches 0, destroy the TLV options general object,
and can now offload a flow with any class/type parameters.
Geneve TLV Options object is added to core device.
It is currently used to manage Geneve TLV options general
object allocation in FW and its reference counting only.
In the future it will also be used for managing geneve ports
by registering callbacks for ndo_udp_tunnel_add/del.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This series provides some low level updates for mlx5 driver needed for
both rdma and netdev trees.
1) Termination flow steering table bits and hardware definitions.
2) Introduce the core dump HW access registers definitions.
3) Refactor and cleans-up VF representors functions handlers.
4) Renames host_params bits to function_changed bits and add the
support for eswitch functions change event in the eswitch general case.
(for both legacy and switchdev modes).
5) Potential error pointer dereference in error handling
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently for every representor type and for every single vport,
representer function pointers copy is stored even though they don't
change from one to other vport.
Additionally priv data entry for the rep is not passed during
registration, but its copied. It is used (set and cleared) by the user
of the reps.
As we want to scale vports, to simplify and also to split constants
from data,
1. Rename mlx5_eswitch_rep_if to mlx5_eswitch_rep_ops as to match _ops
prefix with other standard netdev, ibdev ops.
2. Constify the IB and Ethernet rep ops structure.
3. Instead of storing copy of all rep function pointers, store copy
per eswitch rep type.
4. Split data and function pointers to mlx5_eswitch_rep_ops and
mlx5_eswitch_rep_data.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Whenever device supports eswitch functions changed event, honor
such device setting. Do not limit it to ECPF.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To support sriov on a E-Switch manager, num_vfs are queried
to the firmware whenever E-Switch manager is notified by
esw_functions_changed event.
Replace host_params event with esw_functions_changed event that reflects
more appropriate naming.
While at it, also correct num_vfs type from int to u16 as expected by
the function mlx5_esw_query_functions().
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Termination table is a flow table with a termination flag. The flag
allows the firmware to assume that the the specified actions are the last
actions list. This assumption allows the FW to safely perform potential
looping logic (e.g. hairpin). Introduce the bits for this attribute.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung
Cheng.
3) Orphan NFC, we'll take the patches directly into my tree. From
Johannes Berg.
4) We can't recycle cloned TCP skbs, from Eric Dumazet.
5) Some flow dissector bpf test fixes, from Stanislav Fomichev.
6) Fix RCU marking and warnings in rhashtable, from Herbert Xu.
7) Fix some potential fib6 leaks, from Eric Dumazet.
8) Fix a _decode_session4 uninitialized memory read bug fix that got
lost in a merge. From Florian Westphal.
9) Fix ipv6 source address routing wrt. exception route entries, from
Wei Wang.
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
To avoid any ambiguity between vport index and vport number,
rename functions that had vport, to vport_num or vport_index appropriately.
vport_num is u16 hence change mlx5_eswitch_index_to_vport_num() return
type to u16.
vport_index is an int in vport array. Hence change input type of vport
index in mlx5_eswitch_index_to_vport_num() to int.
Correct multiple eswitch representor interfaces use type u16 of
rep->vport as type int vport_index.
Send vport FW commands with correct eswitch u16 vport_num instead
host int vport_index.
Fixes: 5ae5162066 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is being sent to get a fix for the gcc 9.1 build warnings, and I've
also pulled in some bug fix patches that were posted in the last two
weeks.
- Avoid the gcc 9.1 warning about overflowing a union member
- Fix the wrong callback type for a single response netlink to doit
- Bug fixes from more usage of the mlx5 devx interface
-----BEGIN PGP SIGNATURE-----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=Lo/s
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull more rdma updates from Jason Gunthorpe:
"This is being sent to get a fix for the gcc 9.1 build warnings, and
I've also pulled in some bug fix patches that were posted in the last
two weeks.
- Avoid the gcc 9.1 warning about overflowing a union member
- Fix the wrong callback type for a single response netlink to doit
- Bug fixes from more usage of the mlx5 devx interface"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
net/mlx5: Set completion EQs as shared resources
IB/mlx5: Verify DEVX general object type correctly
RDMA/core: Change system parameters callback from dumpit to doit
RDMA: Directly cast the sockaddr union to sockaddr
Mark completion EQs as shared resources so that they can be used by CQs
with uid != 0.
Fixes: 7efce3691d ("IB/mlx5: Add obj create and destroy functionality")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This has been a smaller cycle than normal. One new driver was accepted,
which is unusual, and at least one more driver remains in review on the
list.
- Driver fixes for hns, hfi1, nes, rxe, i40iw, mlx5, cxgb4, vmw_pvrdma
- Many patches from MatthewW converting radix tree and IDR users to use
xarray
- Introduction of tracepoints to the MAD layer
- Build large SGLs at the start for DMA mapping and get the driver to
split them
- Generally clean SGL handling code throughout the subsystem
- Support for restricting RDMA devices to net namespaces for containers
- Progress to remove object allocation boilerplate code from drivers
- Change in how the mlx5 driver shows representor ports linked to VFs
- mlx5 uapi feature to access the on chip SW ICM memory
- Add a new driver for 'EFA'. This is HW that supports user space packet
processing through QPs in Amazon's cloud
-----BEGIN PGP SIGNATURE-----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=TS64
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle than normal. One new driver was
accepted, which is unusual, and at least one more driver remains in
review on the list.
Summary:
- Driver fixes for hns, hfi1, nes, rxe, i40iw, mlx5, cxgb4,
vmw_pvrdma
- Many patches from MatthewW converting radix tree and IDR users to
use xarray
- Introduction of tracepoints to the MAD layer
- Build large SGLs at the start for DMA mapping and get the driver to
split them
- Generally clean SGL handling code throughout the subsystem
- Support for restricting RDMA devices to net namespaces for
containers
- Progress to remove object allocation boilerplate code from drivers
- Change in how the mlx5 driver shows representor ports linked to VFs
- mlx5 uapi feature to access the on chip SW ICM memory
- Add a new driver for 'EFA'. This is HW that supports user space
packet processing through QPs in Amazon's cloud"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (186 commits)
RDMA/ipoib: Allow user space differentiate between valid dev_port
IB/core, ipoib: Do not overreact to SM LID change event
RDMA/device: Don't fire uevent before device is fully initialized
lib/scatterlist: Remove leftover from sg_page_iter comment
RDMA/efa: Add driver to Kconfig/Makefile
RDMA/efa: Add the efa module
RDMA/efa: Add EFA verbs implementation
RDMA/efa: Add common command handlers
RDMA/efa: Implement functions that submit and complete admin commands
RDMA/efa: Add the ABI definitions
RDMA/efa: Add the com service API definitions
RDMA/efa: Add the efa_com.h file
RDMA/efa: Add the efa.h header file
RDMA/efa: Add EFA device definitions
RDMA: Add EFA related definitions
RDMA/umem: Remove hugetlb flag
RDMA/bnxt_re: Use core helpers to get aligned DMA address
RDMA/i40iw: Use core helpers to get aligned DMA address within a supported page size
RDMA/verbs: Add a DMA iterator to return aligned contiguous memory blocks
RDMA/umem: Add API to find best driver supported page size in an MR
...
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes: f121e0ea95 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit broke the offsets of hca cap struct, fix it.
While at it, cleanup a white space introduced by the same commit.
Fixes: b169e64a24 ("net/mlx5: Geneve, Add flow table capabilities for Geneve decap with TLV options")
Reported-by: Qian Cai <cai@lca.pw>
Cc: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce support for Geneve flow specification and allow
the creation of rules that are matching on basic Geneve
protocol fields: VNI, OAM bit, protocol type, options length.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When in switchdev mode, we would like to treat loopback RoCE
traffic (on eswitch manager) as RDMA and not as regular
Ethernet traffic
In order to enable it we add flow steering rule that forward RoCE
loopback traffic to the HW RoCE filter (by adding allow rule).
In addition we add RoCE address in GID index 0, which will be
set in the RoCE loopback packet.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow table supports three types of miss action:
1. Default miss action - go to default miss table according to table.
2. Go to specific table.
3. Switch domain - go to the root table of an alternative steering
table domain.
New table miss action was added - switch_domain.
The next domain for RDMA_RX namespace is the NIC RX domain.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5 core stores copy of the PCI device name in a
mlx5_priv structure and uses pr_warn, pr_err helpers.
Get rid of the copy of this name; instead store the parent device
pointer that contains name as well as dma specific parameters.
This also allows to use kernel's well defined dev_warn, dev_err, dev_dbg
device specific print routines.
This is also a preparation patch to access non PCI parent device in
future.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets will be
tagged with VLAN ID 0x000 (priority tag) and pop/push actions will be
replaced by VLAN re-write actions (which are supported by the HW).
Introduce prio tag mode as a pre-step to controlling the workaround
behavior.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Ariel Levkovich says:
====================
The series exposes the ICM address of the receive transport
interface (TIR) of Raw Packet and RSS QPs to the user since they are
required to properly create and insert steering rules that direct flows to
these QPs.
====================
For dependencies this branch is based on mlx5-next from
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
* branch 'mlx5_tir_icm':
IB/mlx5: Expose TIR ICM address to user space
net/mlx5: Introduce new TIR creation core API
net/mlx5: Expose TIR ICM address in command outbox
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introducing new TIR creation core API which allows caller
to receive back from the call the full command outbox.
This comes as a preparation for the next patch that will
retrieve the TIR ICM address from the command outbox.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding the TIR ICM address to the create_tir command outbox
through which the device reports the ICM address of the newly
created TIR.
The TIR address can be used for direct attachment to a steering
rule in SW managed steering mode.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add SW ICM related fields to the device memory capabilities
structure and sw ownership capability in flow table properties.
The currently supported SW ICM types are steering and header modify
and the changes exposes the device memory capabilities for each
of these two types.
SW ICM memory can be allocated by SW and then be accessed by RDMA
operations for direct management of the HW packet handling tables.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Arnd Bergmann