Commit Graph

842 Commits

Author SHA1 Message Date
Ivan Khoronzhuk a942312034 net: ethernet: ti: cpts: move enable/disable flags outside of cpts module
Each slave has it's own receive timestamp filter. But cpts rx/tx
timestamp enable flags are used to allow ts retrieve only for one
user. This limitation causes data path redundancy and setting overlap
if cpsw module is in dual-mac mode for instance.

If rx ts is enabled only for one port - the second interface must expect
every incoming packet to be PTP packet w/o absolutely any reason, and if
it's PTP - do unneeded stuff, as rx filter for second port is not set
and cpts fifo is not supposed to contain appropriate ts event.
That's not correct.

So, to fix control overlap and avoid redundant CPU cycles, the patch
splits rx/tx ts enable flags between network devices. After the patch,
PTP timestamping still should be used for only one port (or PTP id
counter has to be different for both ports as cpts IP is common).

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13 16:29:59 -08:00
Ivan Khoronzhuk f19dcd5f11 net: ethernet: ti: cpts: purge staled skbs from txq
The overflow event is running with 1 jiffy in case if txq is not
empty, but it can be emptied completely only if next tx event
consumes skb or deletes staled skb from the txq. In case of staled
skb, that can happen for some unpredictable reason (the ts event was
lost or timed out), the overflow event can be generated quite long
time consuming CPU w/o reason before next tx event happens. To avoid
it, purge txq before increasing overflow event rate.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13 16:29:59 -08:00
Ivan Khoronzhuk d0e14c4d9b net: ethernet: ti: cpts: correct debug for expired txq skb
The msgtype and seqid that is smth that belongs to event for
comparison but not for staled txq skb.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13 16:29:59 -08:00
Ivan Khoronzhuk 00fe471205 net: ethernet: ti: cpsw: fix vlan configuration while down/up
The vlan configuration is not restored after interface donw/up sequence
(if dual-emac - both interfaces). Tested on am572x EVM.

Steps to check:
~# ip link add link eth1 name eth1.100 type vlan id 100
~# ifconfig eth0 down
~# ifconfig eth1 down

Try to remove vid and observe warning:
~# ip link del eth1.100
[  739.526757] net eth1: removing vlanid 100 from vlan filter
[  739.533322] failed to kill vid 0081/100 for device eth1

This patch fixes it, restoring only vlan ALE entries and all other
unicast/multicast entries are restored by system calling rx_mode ndo.

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-08 20:30:58 -08:00
Ivan Khoronzhuk 15180eca56 net: ethernet: ti: cpsw: fix vlan mcast
At this moment, mcast addresses are added for real device only
(reserved vlans for dual-emac mode), even if a mcast address was added
for some vlan only, thus ALE doesn't have corresponding vlan mcast
entries after vlan socket joined multicast group. So ALE drops vlan
frames with mcast addresses intended for vlans and potentially can
receive mcast frames for base ndev. That's not correct. So, fix it by
creating only vlan/mcast entries as requested. Patch doesn't use any
additional lists and is based on device mc address list and cpsw ALE
table entries.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-08 20:30:58 -08:00
Ivan Khoronzhuk 9737cc99dd net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
After flushing all mcast entries from the table, the ones contained in
mc list of ndev are not restored when promisc mode is toggled off,
because they are considered as synched with ALE, thus, in order to
restore them after promisc mode - reset syncing info. This fix
touches only switch mode devices, including single port boards
like Beagle Bone.

Fixes: commit 5da1948969
("net: ethernet: ti: cpsw: fix lost of mcast packets while rx_mode update")

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-22 20:20:14 -07:00
Wolfram Sang 762b9e9abb net: ethernet: ti: davinci_emac: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-21 21:10:12 -07:00
Wolfram Sang 4e13c25227 net: ethernet: ti: cpsw: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-21 21:10:12 -07:00
Ivan Khoronzhuk 5b3a5a14f8 net: ethernet: ti: cpsw: use for mcast entries only host port
In dual-emac mode the cpsw driver sends directed packets, that means
that packets go to the directed port, but an ALE lookup is performed
to determine untagged egress only. It means that on tx side no need
to add port bit for ALE mcast entry mask, and basically ALE entry
for port identification is needed only on rx side.

So, add only host port in dual_emac mode as used directed
transmission, and no need in one more port. For single port boards
and switch mode all ports used, as usual, so no changes for them.
Also it simplifies farther changes.

In other words, mcast entries for dual-emac should behave exactly
like unicast. It also can help avoid leaking packets between ports
with same vlan on h/w level if ports could became members of same vid.

So now, for instance, if mcast address 33:33:00:00:00:01 is added then
entries in ALE table:

vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1

Instead of:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x3
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x5

With the same considerations, set only host port for unregistered
mcast for dual-emac mode in case of IFF_ALLMULTI is set, exactly like
it's done in cpsw_ale_set_allmulti().

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:22:12 -07:00
Ivan Khoronzhuk 5da1948969 net: ethernet: ti: cpsw: fix lost of mcast packets while rx_mode update
Whenever kernel or user decides to call rx mode update, it clears
every multicast entry from forwarding table and in some time adds
it again. This time can be enough to drop incoming multicast packets.

That's why clear only staled multicast entries and update or add new
one afterwards.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:21:28 -07:00
Ivan Khoronzhuk 58bdeac8b0 net: ethernet: ti: cpsw_ale: use const for API having pointer on mac address
It allows to use function under callbacks with same const qualifier of
mac address for farther changes.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:21:27 -07:00
zhong jiang a90546e83a net: ti: Use FIELD_SIZEOF directly instead of reimplementing its function
FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-19 20:58:05 -07:00
David S. Miller e366fa4350 Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net
Two new tls tests added in parallel in both net and net-next.

Used Stephen Rothwell's linux-next resolution.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18 09:33:27 -07:00
Corentin Labbe f025571e96 net: ethernet: ti: add missing GENERIC_ALLOCATOR dependency
This patch mades TI_DAVINCI_CPDMA select GENERIC_ALLOCATOR.
without that, the following sparc64 build failure happen

drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
(.text+0x278): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit':
(.text+0x340): undefined reference to `gen_pool_alloc'
(.text+0x5c4): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x64c): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.6':
davinci_cpdma.c:(.text+0x17ac): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x17b8): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x1824): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x1830): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
(.text+0x19f8): undefined reference to `devm_gen_pool_create'
(.text+0x1a90): undefined reference to `gen_pool_add_virt'
Makefile:1011: recipe for target 'vmlinux' failed

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 07:49:33 -07:00
David S. Miller 36302685f5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-09-04 21:33:03 -07:00
Tony Lindgren 18eb8aea7f net: ethernet: cpsw-phy-sel: prefer phandle for phy sel
The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.

Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.

Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.

Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.

For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.

Cc: devicetree@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-02 13:52:13 -07:00
Rob Herring 21c328dcec net: ethernet: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29 19:41:30 -07:00
David S. Miller 6a92ef08a1 Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net 2018-08-11 17:52:00 -07:00
Ivan Khoronzhuk 803c4f64d7 net: ethernet: ti: cpsw: fix runtime_pm while add/kill vlan
It's exclusive with normal behaviour but if try to set vlan to one of
the reserved values is made, the cpsw runtime pm is broken.

Fixes: a6c5d14f51 ("drivers: net: cpsw: ndev: fix accessing to suspended device")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-11 09:38:53 -07:00
Ivan Khoronzhuk be35b982e8 net: ethernet: ti: cpsw: clear all entries when delete vid
In cases if some of the entries were not found in forwarding table
while killing vlan, the rest not needed entries still left in the
table. No need to stop, as entry was deleted anyway. So fix this by
returning error only after all was cleaned. To implement this, return
-ENOENT in cpsw_ale_del_mcast() as it's supposed to be.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-11 09:38:53 -07:00
Gustavo A. R. Silva e38c2e11eb net: ethernet: ti: cpts: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 114813 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-07 17:54:21 -07:00
Gustavo A. R. Silva 681685a1ce net: tlan: Mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 141440 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-07 17:54:21 -07:00
Ivan Khoronzhuk fea49f60c9 net: ethernet: ti: cpsw: replace unnecessarily macroses on functions
Replace ugly macroses on functions.

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-01 09:29:24 -07:00
Ivan Khoronzhuk 193736c817 net: ethernet: ti: cpsw: add missed RX_CTAG feature for second slave
Seems it was missed while adding for first net dev in dual-emac mode.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-29 12:51:31 -07:00
Ivan Khoronzhuk 4b4255ed06 net: ethernet: ti: cpsw: restore shaper configuration while down/up
Need to restore shapers configuration after interface was down/up.
This is needed as appropriate configuration is still replicated in
kernel settings. This only shapers context restore, so vlan
configuration should be restored by user if needed, especially for
devices with one port where vlan frames are sent via ALE.

Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 20:34:36 -07:00
Ivan Khoronzhuk 57d9014825 net: ethernet: ti: cpsw: add CBS Qdisc offload
The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate
limited queue with shaping. In order to set and enable shaping for
those 3 FIFOs queues the network device with CBS qdisc attached is
needed. The CBS configuration is added for dual-emac/single port mode
only, but potentially can be used in switch mode also, based on
switchdev for instance.

Despite the FIFO shapers can work w/o cpdma level shapers the base
usage must be in combine with cpdma level shapers as described in TRM,
that are set as maximum rates for interface queues with sysfs.

One of the possible configuration with txq shapers and CBS shapers:

                      Configured with echo RATE >
                  /sys/class/net/eth0/queues/tx-0/tx_maxrate
             /---------------------------------------------------
            /
           /            cpdma level shapers
        +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+
        | c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 |
        \    / \    / \    / \    / \    / \    / \    / \    /
         \  /   \  /   \  /   \  /   \  /   \  /   \  /   \  /
          \/     \/     \/     \/     \/     \/     \/     \/
+---------|------|------|------|-------------------------------------+
|    +----+      |      |  +---+                                     |
|    |      +----+      |  |                                         |
|    v      v           v  v                                         |
| +----+ +----+ +----+ +----+ p        p+----+ +----+ +----+ +----+  |
| |    | |    | |    | |    | o        o|    | |    | |    | |    |  |
| | f3 | | f2 | | f1 | | f0 | r  CPSW  r| f3 | | f2 | | f1 | | f0 |  |
| |    | |    | |    | |    | t        t|    | |    | |    | |    |  |
| \    / \    / \    / \    / 0        1\    / \    / \    / \    /  |
|  \  X   \  /   \  /   \  /             \  /   \  /   \  /   \  /   |
|   \/ \   \/     \/     \/               \/     \/     \/     \/    |
+-------\------------------------------------------------------------+
         \
          \ FIFO shaper, set with CBS offload added in this patch,
           \ FIFO0 cannot be rate limited
            ------------------------------------------------------

CBS shaper configuration is supposed to be used with root MQPRIO Qdisc
offload allowing to add sk_prio->tc->txq maps that direct traffic to
appropriate tx queue and maps L2 priority to FIFO shaper.

The CBS shaper is intended to be used for AVB where L2 priority
(pcp field) is used to differentiate class of traffic. So additionally
vlan needs to be created with appropriate egress sk_prio->l2 prio map.

If CBS has several tx queues assigned to it, the sum of their
bandwidth has not overlap bandwidth set for CBS. It's recomended the
CBS bandwidth to be a little bit more.

The CBS shaper is configured with CBS qdisc offload interface using tc
tool from iproute2 packet.

For instance:

$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1

$ tc -g class show dev eth0
+---(100:ffe2) mqprio
|    +---(100:3) mqprio
|    +---(100:4) mqprio
|    
+---(100:ffe1) mqprio
|    +---(100:2) mqprio
|    
+---(100:ffe0) mqprio
     +---(100:1) mqprio

$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \
hicredit 60 sendslope -960000 idleslope 40000 offload 1

$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \
hicredit 62 sendslope -980000 idleslope 20000 offload 1

The above code set CBS shapers for tc0 and tc1, for that txq0 and
txq1 is used. Pay attention, the real set bandwidth can differ a bit
due to discreteness of configuration parameters.

Here parameters like locredit, hicredit and sendslope are ignored
internally and are supposed to be set with assumption that maximum
frame size for frame - 1500.

It's supposed that interface speed is not changed while reconnection,
not always is true, so inform user in case speed of interface was
changed, as it can impact on dependent shapers configuration.

For more examples see Documentation.

Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 20:34:36 -07:00
Ivan Khoronzhuk 7929a66871 net: ethernet: ti: cpsw: add MQPRIO Qdisc offload
That's possible to offload vlan to tc priority mapping with
assumption sk_prio == L2 prio.

Example:
$ ethtool -L eth0 rx 1 tx 4

$ qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1

$ tc -g class show dev eth0
+---(100:ffe2) mqprio
|    +---(100:3) mqprio
|    +---(100:4) mqprio
|    
+---(100:ffe1) mqprio
|    +---(100:2) mqprio
|    
+---(100:ffe0) mqprio
     +---(100:1) mqprio

Here, 100:1 is txq0, 100:2 is txq1, 100:3 is txq2, 100:4 is txq3
txq0 belongs to tc0, txq1 to tc1, txq2 and txq3 to tc2
The offload part only maps L2 prio to classes of traffic, but not
to transmit queues, so to direct traffic to traffic class vlan has
to be created with appropriate egress map.

Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 20:34:36 -07:00
Ivan Khoronzhuk 4bb6c356a0 net: ethernet: ti: cpdma: fit rated channels in backward order
According to TRM tx rated channels should be in 7..0 order,
so correct it.

Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 20:34:36 -07:00
Ivan Khoronzhuk 79b3325d0d net: ethernet: ti: cpsw: use cpdma channels in backward order for txq
The cpdma channel highest priority is from hi to lo number.
The driver has limited number of descriptors that are shared between
number of cpdma channels. Number of queues can be tuned with ethtool,
that allows to not spend descriptors on not needed cpdma channels.
In AVB usually only 2 tx queues can be enough with rate limitation.
The rate limitation can be used only for hi priority queues. Thus, to
use only 2 queues the 8 has to be created. It's wasteful.

So, in order to allow using only needed number of rate limited
tx queues, save resources, and be able to set rate limitation for
them, let assign tx cpdma channels in backward order to queues.

Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-23 20:34:36 -07:00
Ivan Khoronzhuk d0c694fc7b net: ethernet: ti: cpts: break cycle once late ts is matched
The late ts queue can contain a bunch of skbs while hi rate testing,
no need to check all of them if timestamp is already matched.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-12 00:00:07 -07:00
Alexander Duyck a4ea8a3dac net: Add generic ndo_select_queue functions
This patch adds a generic version of the ndo_select_queue functions for
either returning 0 or selecting a queue based on the processor ID. This is
generally meant to just reduce the number of functions we have to change
in the future when we have to deal with ndo_select_queue changes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-07-09 13:15:34 -07:00
Ivan Khoronzhuk 1c0e8123e3 net: ethernet: ti: cpsw: allow PTP 224.0.0.107 to be timestamped
Tested on AM572x with cpsw v1.15 for PTP sync and delay_req messages.
It doesn't work on cpsw v1.12, so added only for cpsw v > 1.15.

Command for testing:
ptp4l -P -4 -H -i eth0 -l 6 -m -q -p /dev/ptp0 -f ptp.cfg
where ptp.cfg:

[global]
tx_timestamp_timeout     20

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-07 21:22:57 +09:00
Ivan Khoronzhuk 1239a96a8f net: ethernet: ti: cpsw: use BIT macro
It's needed to avoid checkpatch warnings for farther changes.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-07 21:22:57 +09:00
Joe Perches 6c1f0a1ffb net: drivers/net: Convert random_ether_addr to eth_random_addr
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1

Convert the uses of random_ether_addr to enable removing the #define

Miscellanea:

o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-23 10:49:14 +09:00
Colin Ian King 40141bb480 net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
The function cpdma_desc_pool_create is local to the source and does not
need to be in global scope, so make it static.

Cleans up sparse warning:
warning: symbol 'cpdma_desc_pool_create' was not declared. Should it
be static?

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-22 09:31:09 +09:00
Bartosz Golaszewski ea0820bb77 net: davinci_emac: match the mdio device against its compatible if possible
Device tree based systems without of_dev_auxdata will have the mdio
device named differently than "davinci_mdio(.0)". In this case use the
device's parent's compatible string for matching

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-21 10:23:48 +09:00
Bartosz Golaszewski dc45519eb1 net: ethernet: fix suspend/resume in davinci_emac
This patch reverts commit 3243ff2a05 ("net: ethernet: davinci_emac:
Deduplicate bus_find_device() by name matching") and adds a comment
which should stop anyone from reintroducing the same "fix" in the future.

We can't use bus_find_device_by_name() here because the device name is
not guaranteed to be 'davinci_mdio'. On some systems it can be
'davinci_mdio.0' so we need to use strncmp() against the first part of
the string to correctly match it.

Fixes: 3243ff2a05 ("net: ethernet: davinci_emac: Deduplicate bus_find_device() by name matching")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20 08:47:56 +09:00
Kees Cook a86854d0c5 treewide: devm_kzalloc() -> devm_kcalloc()
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:

        devm_kzalloc(handle, a * b, gfp)

with:
        devm_kcalloc(handle, a * b, gfp)

as well as handling cases of:

        devm_kzalloc(handle, a * b * c, gfp)

with:

        devm_kzalloc(handle, array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        devm_kcalloc(handle, array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        devm_kzalloc(handle, 4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@

(
  devm_kzalloc(HANDLE,
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  devm_kzalloc(HANDLE,
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@

- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@

(
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
  devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * E2
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
YueHaibing a6ee84be2c net: netcp: ethss: remove unnecessary pointer set to NULL
If statement has make sure the 'slave->phy' is NULL

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03 10:39:48 -04:00
David S. Miller 9c54aeb03a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03 09:31:58 -04:00
Dan Carpenter 8005b09d99 net: ethernet: davinci_emac: fix error handling in probe()
The current error handling code has an issue where it does:

	if (priv->txchan)
		cpdma_chan_destroy(priv->txchan);

The problem is that ->txchan is either valid or an error pointer (which
would lead to an Oops).  I've changed it to use multiple error labels so
that the test can be removed.

Also there were some missing calls to netif_napi_del().

Fixes: 3ef0fdb234 ("net: davinci_emac: switch to new cpdma layer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-31 16:12:00 -04:00
Arnd Bergmann e2b3e49378 net: ti: cpsw: include gpio/consumer.h
On platforms that don't always enable CONFIG_GPIOLIB, we run into
a build failure:

drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_probe':
drivers/net/ethernet/ti/cpsw.c:3006:9: error: implicit declaration of function 'devm_gpiod_get_array_optional' [-Werror=implicit-function-declaration]
  mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/cpsw.c:3006:59: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
  mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);

Since we cannot rely on this to be visible from gpio.h, we have to include
gpio/consumer.h directly.

Fixes: 2652113ff0 ("net: ethernet: ti: Allow most drivers with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-31 15:46:41 -04:00
Arnd Bergmann 37c9102f21 net: davinci: fix building davinci mdio code without CONFIG_OF
Test-building this driver on targets without CONFIG_OF revealed a build
failure:

drivers/net/ethernet/ti/davinci_mdio.c: In function 'davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:380:9: error: implicit declaration of function 'davinci_mdio_probe_dt'; did you mean 'davinci_mdio_probe'? [-Werror=implicit-function-declaration]

This adjusts the #ifdef logic in the driver to make it build in
all configurations.

Fixes: 2652113ff0 ("net: ethernet: ti: Allow most drivers with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-30 13:21:23 -04:00
Florian Fainelli c79c385044 ti: ethernet: davinci: Fix cast to int warnings
Now that we can compile test this driver on 64-bit hosts, we get some
warnings about how a pointer/address is written/read to/from a register
(sw_token). Fix this by doing the appropriate conversions, we cannot
possibly have the driver work on 64-bit hosts the way the tokens are
managed though, since the registers being written to a 32-bit only.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21 16:17:10 -04:00
Florian Fainelli 5a04e8f81a net: ethernet: davinci_emac: Fix printing of base address
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.

Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21 16:17:10 -04:00
Florian Fainelli bf2ce3fdf3 net: ethernet: ti: cpsw: Fix cpsw_add_ch_strings() printk format
When building on a 64-bit host we will get the following warning:

drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
     "%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
                  ~^
                  %ld

Fix this by using an %ld format and casting to long.

Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21 16:17:10 -04:00
Florian Fainelli ea5ec9fc9e net: ethernet: ti: cpts: Fix timestamp print
On 64-bit hosts we will get the following warning:

drivers/net/ethernet/ti/cpts.c: In function 'cpts_overflow_check':
drivers/net/ethernet/ti/cpts.c:297:11: warning: format '%lld' expects
argument of type 'long long int', but argument 3 has type
'__kernel_time_t {aka long int}' [-Wformat=]
  pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec,
ts.tv_nsec);

Fix this by using an appropriate casting that works on all bit sizes.

Fixes: a5c79c26e1 ("ptp: cpts: convert to the 64 bit get/set time methods.")
Fixes: 87c0e764d4 ("cpts: introduce time stamping code and a PTP hardware clock.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21 16:17:10 -04:00
Florian Fainelli b4eb739368 ti: ethernet: cpdma: Use correct format for genpool_*
Now that we can compile davinci_cpdma.c on 64-bit hosts, we can see that
the format used for printing a size_t type is incorrect, use %zd
accordingly.

Fixes: aeec302104 ("net: ethernet: ti: cpdma: remove used_desc counter")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-21 16:17:09 -04:00
Florian Fainelli 2652113ff0 net: ethernet: ti: Allow most drivers with COMPILE_TEST
Most of the TI drivers build just fine with COMPILE_TEST, cpmac (AR7) is
the exception because it uses a header file from
arch/mips/include/asm/mach-ar7/ar7.h and keystone netcp which requires
help from drivers/soc/ti/ for queue management helpers.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-17 17:11:06 -04:00
Ivan Khoronzhuk 9611d6d6e2 net: ethernet: ti: cpsw: disable mq feature for "AM33xx ES1.0" devices
The early versions of am33xx devices, related to ES1.0 SoC revision
have errata limiting mq support. That's the same errata as
commit 7da1160002 ("drivers: net: cpsw: add am335x errata workarround for
interrutps")

AM33xx Errata [1] Advisory 1.0.9
http://www.ti.com/lit/er/sprz360f/sprz360f.pdf

After additional investigation were found that drivers w/a is
propagated on all AM33xx SoCs and on DM814x. But the errata exists
only for ES1.0 of AM33xx family, limiting mq support for revisions
after ES1.0. So, disable mq support only for related SoCs and use
separate polls for revisions allowing mq.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-17 15:11:55 -04:00
Florian Fainelli 00e798c7d1 drivers: net: Remove device_node checks with of_mdiobus_register()
A number of drivers have the following pattern:

if (np)
	of_mdiobus_register()
else
	mdiobus_register()

which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-16 14:20:36 -04:00
Grygorii Strashko c6213eb1ae net: ethernet: ti: cpsw-phy-sel: check bus_find_device() ret value
This fixes klockworks warnings: Pointer 'dev' returned from call to
function 'bus_find_device' at line 179 may be NULL and will be dereferenced
at line 181.

    cpsw-phy-sel.c:179: 'dev' is assigned the return value from function 'bus_find_device'.
    bus.c:342: 'bus_find_device' explicitly returns a NULL value.
    cpsw-phy-sel.c:181: 'dev' is dereferenced by passing argument 1 to function 'dev_get_drvdata'.
    device.h:1024: 'dev' is passed to function 'dev_get_drvdata'.
    device.h:1026: 'dev' is explicitly dereferenced.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[nsekhar@ti.com: add an error message, fix return path]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-16 14:13:13 -04:00
Hernán Gonzalez bde4c563a9 net: ethernet: ti: Use ERR_CAST instead of ERR_PTR(PTR_ERR())
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...)).

drivers/net/ethernet/ti/cpts.c:567:9-16: WARNING: ERR_CAST can be used with cpts->refclk
Generated by: scripts/coccinelle/api/err_cast.cocci

Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-14 16:27:59 -04:00
Sekhar Nori 54472edff0 drivers: net: davinci_mdio: prevent spurious timeout
A well timed kernel preemption in the time_after() loop
in wait_for_idle() can result in a spurious timeout
error to be returned.

Fix it by using readl_poll_timeout() which takes care of
this issue.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-10 16:18:59 -04:00
David S. Miller a7b15ab887 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Overlapping changes in selftests Makefile.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-04 09:58:56 -04:00
Grygorii Strashko 5e5add172e net: ethernet: ti: cpsw: fix packet leaking in dual_mac mode
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
 - connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
 - connect port 2 (eth1) to linux Host 1 with vlan 1 configured
 - ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.

Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.

To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-02 11:08:23 -04:00
David S. Miller c749fa181b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-04-24 23:59:11 -04:00
Ivan Khoronzhuk 5e391dc5a8 net: ethernet: ti: cpsw: fix tx vlan priority mapping
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.

Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-22 14:55:43 -04:00
WingMan Kwok 8585661b1a net: netcp: ethss: k2g: add promiscuous mode support
This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.

Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:58 -04:00
WingMan Kwok 0542a87c54 net: netcp: add api to support set rx mode in netcp modules
This patch adds an API to support setting rx mode in
netcp modules.  If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch.  Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.

Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri 21f706bb10 net: netcp: support probe deferral
The netcp driver shouldn't proceed until the knav qmss and dma
devices are ready. So return -EPROBE_DEFER if these devices are not
ready.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri c52b6782d0 Revert "net: netcp: remove dead code from the driver"
As the probe sequence is not guaranteed contrary to the assumption
of the commit 2d8e276a9030, same has to be reverted.

commit 2d8e276a9030 ("net: netcp: remove dead code from the driver")

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri 7b647b93b3 net: netcp: ethss: use of_get_phy_mode() to support different RGMII modes
The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri dc07ec9736 net: netcp: ethss: re-use stats handling code for 2u hardware
The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri 65c450642c net: netcp: ethss: map vlan priorities to zero flow
The driver currently support only vlan priority zero. So map the
vlan priorities to zero flow in hardware.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri 7771f2b4d0 net: netcp: ethss: use rgmii link status for 2u cpsw hardware
Introduce rgmii link status to handle link state events for 2u
cpsw hardware on K2G.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:57 -04:00
Murali Karicheri 478e9a5fcf net: netcp: ethss: add support for handling rgmii link interface
2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:56 -04:00
Murali Karicheri 775f9535dc net: netcp: ethss: make sgmii configuration conditional
As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:56 -04:00
Murali Karicheri 2953586df7 net: netcp: ethss: use macro for checking ss_version consistently
Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18 21:00:56 -04:00
Linus Torvalds 3b54765cca Merge branch 'akpm' (patches from Andrew)
Merge updates from Andrew Morton:

 - a few misc things

 - ocfs2 updates

 - the v9fs maintainers have been missing for a long time. I've taken
   over v9fs patch slinging.

 - most of MM

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
  mm,oom_reaper: check for MMF_OOM_SKIP before complaining
  mm/ksm: fix interaction with THP
  mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
  headers: untangle kmemleak.h from mm.h
  include/linux/mmdebug.h: make VM_WARN* non-rvals
  mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
  mm: change return type to vm_fault_t
  mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
  mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
  kernel/fork.c: detect early free of a live mm
  mm: make counting of list_lru_one::nr_items lockless
  mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
  block_invalidatepage(): only release page if the full page was invalidated
  mm: kernel-doc: add missing parameter descriptions
  mm/swap.c: remove @cold parameter description for release_pages()
  mm/nommu: remove description of alloc_vm_area
  zram: drop max_zpage_size and use zs_huge_class_size()
  zsmalloc: introduce zs_huge_class_size()
  mm: fix races between swapoff and flush dcache
  fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
  ...
2018-04-06 14:19:26 -07:00
Randy Dunlap 514c603249 headers: untangle kmemleak.h from mm.h
Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason.  It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it.  Also remove <linux/kmemleak.h> from source
files that do not use it.

This is tested on i386 allmodconfig and x86_64 allmodconfig.  It would
be good to run it through the 0day bot for other $ARCHes.  I have
neither the horsepower nor the storage space for the other $ARCHes.

Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms.  Both of them reported 2 build failures
for which patches are included here (in v2).

[ slab.h is the second most used header file after module.h; kernel.h is
  right there with slab.h. There could be some minor error in the
  counting due to some #includes having comments after them and I didn't
  combine all of those. ]

[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>	[2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>	[2 build failures]
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-05 21:36:27 -07:00
Linus Torvalds 672a9c1069 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
  kfifo: fix inaccurate comment
  tools/thermal: tmon: fix for segfault
  net: Spelling s/stucture/structure/
  edd: don't spam log if no EDD information is present
  Documentation: Fix early-microcode.txt references after file rename
  tracing: Block comments should align the * on each line
  treewide: Fix typos in printk
  GenWQE: Fix a typo in two comments
  treewide: Align function definition open/close braces
2018-04-05 11:56:35 -07:00
Geert Uytterhoeven b903036aad net: Spelling s/stucture/structure/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-03-27 09:51:23 +02:00
David S. Miller 03fe2debbb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Fun set of conflict resolutions here...

For the mac80211 stuff, these were fortunately just parallel
adds.  Trivially resolved.

In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.

In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.

The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.

The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:

====================

    Due to bug fixes found by the syzkaller bot and taken into the for-rc
    branch after development for the 4.17 merge window had already started
    being taken into the for-next branch, there were fairly non-trivial
    merge issues that would need to be resolved between the for-rc branch
    and the for-next branch.  This merge resolves those conflicts and
    provides a unified base upon which ongoing development for 4.17 can
    be based.

    Conflicts:
            drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
            (IB/mlx5: Fix cleanup order on unload) added to for-rc and
            commit b5ca15ad7e (IB/mlx5: Add proper representors support)
            add as part of the devel cycle both needed to modify the
            init/de-init functions used by mlx5.  To support the new
            representors, the new functions added by the cleanup patch
            needed to be made non-static, and the init/de-init list
            added by the representors patch needed to be modified to
            match the init/de-init list changes made by the cleanup
            patch.
    Updates:
            drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
            prototypes added by representors patch to reflect new function
            names as changed by cleanup patch
            drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
            stage list to match new order from cleanup patch
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-23 11:31:58 -04:00
Grygorii Strashko a3a41d2f94 net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:

 HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
 HDR_PKT_CFI 	  bits 28 - Header Packet VLAN CFI bit.
 HDR_PKT_Vid 	  bits 27-16 - Header Packet VLAN ID
 PKT_Type         bits 8-9 - Packet Type. Indicates whether the packet is
                 	VLAN-tagged, priority-tagged, or non-tagged.
	00: VLAN-tagged packet
	01: Reserved
	10: Priority-tagged packet
	11: Non-tagged packet

This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).

Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17 19:51:01 -04:00
SZ Lin (林上智) f9db50691d net: ethernet: ti: cpsw: add check for in-band mode setting with RGMII PHY interface
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].

This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.

References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155

Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17 19:49:34 -04:00
Grygorii Strashko 62f94c2101 net: ethernet: ti: cpsw: fix net watchdog timeout
It was discovered that simple program which indefinitely sends 200b UDP
packets and runs on TI AM574x SoC (SMP) under RT Kernel triggers network
watchdog timeout in TI CPSW driver (<6 hours run). The network watchdog
timeout is triggered due to race between cpsw_ndo_start_xmit() and
cpsw_tx_handler() [NAPI]

cpsw_ndo_start_xmit()
	if (unlikely(!cpdma_check_free_tx_desc(txch))) {
		txq = netdev_get_tx_queue(ndev, q_idx);
		netif_tx_stop_queue(txq);

^^ as per [1] barier has to be used after set_bit() otherwise new value
might not be visible to other cpus
	}

cpsw_tx_handler()
	if (unlikely(netif_tx_queue_stopped(txq)))
		netif_tx_wake_queue(txq);

and when it happens ndev TX queue became disabled forever while driver's HW
TX queue is empty.

Fix this, by adding smp_mb__after_atomic() after netif_tx_stop_queue()
calls and double check for free TX descriptors after stopping ndev TX queue
- if there are free TX descriptors wake up ndev TX queue.

[1] https://www.kernel.org/doc/html/latest/core-api/atomic_ops.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-07 21:57:10 -05:00
David S. Miller 8565d26bcb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The BPF verifier conflict was some minor contextual issue.

The TUN conflict was less trivial.  Cong Wang fixed a memory leak of
tfile->tx_array in 'net'.  This is an skb_array.  But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-19 22:59:33 -05:00
Rex Chang 5a71784317 Net: ethernet: ti: netcp: Fix inbound ping crash if MTU size is greater than 1500
In the receive queue for 4096 bytes fragments, the page address
set in the SW data0 field of the descriptor is not the one we got
when doing the reassembly in receive. The page structure was retrieved
from the wrong descriptor into SW data0 which is then causing a
page fault when UDP checksum is accessing data above 1500.

Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-17 16:19:37 -05:00
Ivan Khoronzhuk 8a83c5d796 net: ethernet: ti: cpdma: correct error handling for chan create
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-13 15:49:53 -05:00
Grygorii Strashko 97193601bb net: ethernet: ti: ale: fix port check in cpsw_ale_control_set/get
ALE ports number includes the Host port and ext Ports, and
ALE ports numbering starts from 0, so correct corresponding port
checks in cpsw_ale_control_set/get().

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:33 -05:00
Grygorii Strashko 1971ab587b net: ethernet: ti: ale: use devm_kzalloc in cpsw_ale_create()
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko fb1a732dd5 net: ethernet: ti: ale: move static initialization in cpsw_ale_create()
Move static initialization from cpsw_ale_start() to cpsw_ale_create() as it
does not make much sence to perform static initializtion in
cpsw_ale_start() which is called everytime netif[s] is opened.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko b5d31f2940 net: ethernet: ti: ale: optimize ale entry mask bits configuartion
The ale->params.ale_ports parameter can be used to deriver values for all
ale entry mask bits: port_mask_bits, port_mask_bits, port_num_bits.
Hence, calculate above values and drop all hardcoded values. For
port_num_bits calcualtion use order_base_2() API.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko d0aef029b5 net: ethernet: ti: ale: disable ale from stop()
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko 4ff2c4bd11 net: ethernet: ti: ale: use proper io apis
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko c6395f1258 net: ethernet: ti: cpsw: fix ale port numbers
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.

Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko 2733d7b89c net: ethernet: ti: cpsw: move mac_hi/lo defines in cpsw.h
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko 2c8a14d626 net: ethernet: ti: cpsw: move platform data struct to .c file
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko dda5f5fe74 net: ethernet: ti: cpsw: use proper io apis
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Grygorii Strashko fc49be85f6 net: ethernet: ti: cpsw: drop unused var poll from cpsw_update_channels_res
Drop unused variable "poll" from cpsw_update_channels_res().

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-01 16:36:32 -05:00
Lukas Wunner 3243ff2a05 net: ethernet: davinci_emac: Deduplicate bus_find_device() by name matching
No need to reinvent the wheel, we have bus_find_device_by_name().

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30 09:24:08 -05:00
Kees Cook 841b86f328 treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:

    perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
        $(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)

    perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
        $(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)

The now unused macros are also dropped from include/linux/timer.h.

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 16:35:54 -08:00
Kees Cook e99e88a9d2 treewide: setup_timer() -> timer_setup()
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

    void my_callback(struct something *ptr)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

    void my_callback(unsigned long data)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

    void my_callback(struct timer_list *unused)
    {
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
	-I ./arch/x86/include -I ./arch/x86/include/generated \
	-I ./include -I ./arch/x86/include/uapi \
	-I ./arch/x86/include/generated/uapi -I ./include/uapi \
	-I ./include/generated/uapi --include ./include/linux/kconfig.h \
	--dir . \
	--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

 setup_timer(
-&(e)
+&e
 , ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
 _E->_timer@_stl.function = _callback;
|
 _E->_timer@_stl.function = &_callback;
|
 _E->_timer@_stl.function = (_cast_func)_callback;
|
 _E->_timer@_stl.function = (_cast_func)&_callback;
|
 _E._timer@_stl.function = _callback;
|
 _E._timer@_stl.function = &_callback;
|
 _E._timer@_stl.function = (_cast_func)_callback;
|
 _E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
 depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
(
	... when != _origarg
	_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
)
 }

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
 depends on change_timer_function_usage &&
                     !change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
+	_handletype *_origarg = from_timer(_origarg, t, _timer);
+
	... when != _origarg
-	(_handletype *)_origarg
+	_origarg
	... when != _origarg
 }

// Avoid already converted callbacks.
@match_callback_converted
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
	    !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

 void _callback(struct timer_list *t)
 { ... }

// callback(struct something *handle)
@change_callback_handle_arg
 depends on change_timer_function_usage &&
	    !match_callback_converted &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

 void _callback(
-_handletype *_handle
+struct timer_list *t
 )
 {
+	_handletype *_handle = from_timer(_handle, t, _timer);
	...
 }

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
 depends on change_timer_function_usage &&
	    change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

 void _callback(struct timer_list *t)
 {
-	_handletype *_handle = from_timer(_handle, t, _timer);
 }

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg &&
	    !change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
 _E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

 _callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
 )

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
 depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *unused
 )
 {
	... when != _origarg
 }

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:57:07 -08:00
Linus Torvalds 8170024750 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Revert regression inducing change to the IPSEC template resolver,
    from Steffen Klassert.

 2) Peeloffs can cause the wrong sk to be waken up in SCTP, fix from Xin
    Long.

 3) Min packet MTU size is wrong in cpsw driver, from Grygorii Strashko.

 4) Fix build failure in netfilter ctnetlink, from Arnd Bergmann.

 5) ISDN hisax driver checks pnp_irq() for errors incorrectly, from
    Arvind Yadav.

 6) Fix fealnx driver build failure on MIPS, from Huacai Chen.

 7) Fix into leak in SCTP, the scope_id of socket addresses is not
    always filled in. From Eric W. Biederman.

 8) MTU inheritance between physical function and representor fix in nfp
    driver, from Dirk van der Merwe.

 9) Fix memory leak in rsi driver, from Colin Ian King.

10) Fix expiration and generation ID handling of cached ipv4 redirect
    routes, from Xin Long.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
  net: usb: hso.c: remove unneeded DRIVER_LICENSE #define
  ibmvnic: fix dma_mapping_error call
  ipvlan: NULL pointer dereference panic in ipvlan_port_destroy
  route: also update fnhe_genid when updating a route cache
  route: update fnhe_expires for redirect when the fnhe exists
  sctp: set frag_point in sctp_setsockopt_maxseg correctly
  rsi: fix memory leak on buf and usb_reg_buf
  net/netlabel: Add list_next_rcu() in rcu_dereference().
  nfp: remove false positive offloads in flower vxlan
  nfp: register flower reprs for egress dev offload
  nfp: inherit the max_mtu from the PF netdev
  nfp: fix vlan receive MAC statistics typo
  nfp: fix flower offload metadata flag usage
  virto_net: remove empty file 'virtio_net.'
  net/sctp: Always set scope_id in sctp_inet6_skb_msgname
  fealnx: Fix building error on MIPS
  isdn: hisax: Fix pnp_irq's error checking for setup_teles3
  isdn: hisax: Fix pnp_irq's error checking for setup_sedlbauer_isapnp
  isdn: hisax: Fix pnp_irq's error checking for setup_niccy
  isdn: hisax: Fix pnp_irq's error checking for setup_ix1micro
  ...
2017-11-17 20:18:37 -08:00
Linus Torvalds 7c225c69f8 Merge branch 'akpm' (patches from Andrew)
Merge updates from Andrew Morton:

 - a few misc bits

 - ocfs2 updates

 - almost all of MM

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
  memory hotplug: fix comments when adding section
  mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
  mm: simplify nodemask printing
  mm,oom_reaper: remove pointless kthread_run() error check
  mm/page_ext.c: check if page_ext is not prepared
  writeback: remove unused function parameter
  mm: do not rely on preempt_count in print_vma_addr
  mm, sparse: do not swamp log with huge vmemmap allocation failures
  mm/hmm: remove redundant variable align_end
  mm/list_lru.c: mark expected switch fall-through
  mm/shmem.c: mark expected switch fall-through
  mm/page_alloc.c: broken deferred calculation
  mm: don't warn about allocations which stall for too long
  fs: fuse: account fuse_inode slab memory as reclaimable
  mm, page_alloc: fix potential false positive in __zone_watermark_ok
  mm: mlock: remove lru_add_drain_all()
  mm, sysctl: make NUMA stats configurable
  shmem: convert shmem_init_inodecache() to void
  Unify migrate_pages and move_pages access checks
  mm, pagevec: rename pagevec drained field
  ...
2017-11-15 19:42:40 -08:00
Mel Gorman 453f85d43f mm: remove __GFP_COLD
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of.  Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact.  Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.

This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache.  Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop.  It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.

The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path.  A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.

Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-15 18:21:06 -08:00
Grygorii Strashko 9421c90150 net: ethernet: ti: cpsw: fix min eth packet size
Now CPSW driver configures min eth packet size to 60 octets (ETH_ZLEN)
which works in most of cases, but when port VLAN is configured on some
switch port, it also can be configured to force all egress packets to be
VLAN untagged. And in this case, CPSW driver will pad small packets to 60
octets, but final packet size on port egress can became less than 60 octets
due to VLAN tag removal and packet will be dropped.

Hence, fix it by accounting VLAN header in CPSW min eth packet size. While
here, use proper defines for CPSW_MAX_PACKET_SIZE also, instead of open
coding.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-16 10:49:00 +09:00
Nogah Frankel 575ed7d39e net_sch: mqprio: Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.

Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-08 12:23:38 +09:00
David S. Miller 2a171788ba Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Files removed in 'net-next' had their license header updated
in 'net'.  We take the remove from 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-04 09:26:51 +09:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Kees Cook 0010e3f8b3 net/ti/tlan: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Samuel Chessman <chessman@tux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-18 12:39:36 +01:00
Allen Pais 8447779637 net: ti: netcp: use setup_timer
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 15:48:46 -07:00
Allen Pais 9d90725f33 drivers: net: cpsw_ale: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:44 -07:00
Ivan Khoronzhuk e333ac1f1d net: ethernet: ti: netcp_core: no need in netif_napi_del
Don't remove rx_napi specifically just before free_netdev(),
it's supposed to be done in it and is confusing w/o tx_napi deletion.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-08 20:53:10 -07:00
David S. Miller 6026e043d0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Three cases of simple overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-01 17:42:05 -07:00
Sekhar Nori f0e82d737d net: ti: cpsw-common: dont print error if ti_cm_get_macid() fails
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.

On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.

Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-30 10:05:07 -07:00
Bhumika Goyal b6d08bd81d net: ethernet: make ptp_clock_info const
Make these const as they are only used in a copy operation.
Done using Coccinelle.

@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};

@ref@
position p;
identifier match.s;
@@
s@p

@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)

@bad depends on  !good1@
position ref.p;
identifier match.s;
@@
s@p

@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-22 11:04:51 -07:00
Arvind Yadav f5b589488e net: ti: cpsw:: constify platform_device_id
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-13 20:12:23 -07:00
Maxim Uvarov cc147a0dc3 drivers: net: davinci_mdio: print bus frequency
Frequency can be adjusted in DT it make sense to
print current used value on driver init.

Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-11 14:23:59 -07:00
Maxim Uvarov 2e1c80847b drivers: net: davinci_mdio: remove busy loop on wait user access
Polling 14 mdio devices on single mdio bus eats 30% of 1Ghz cpu time
due to busy loop in wait(). Add small delay to relax cpu.

Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-11 14:23:59 -07:00
David S. Miller 3118e6e19d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.

The TCP conflict was a case of local variables in a function
being removed from both net and net-next.

In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-09 16:28:45 -07:00
Jiri Pirko de4784ca03 net: sched: get rid of struct tc_to_netdev
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07 09:42:37 -07:00
Jiri Pirko 38cf0426e5 net: sched: change return value of ndo_setup_tc for driver supporting mqprio only
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07 09:42:37 -07:00
Jiri Pirko 5fd9fc4e20 net: sched: push cls related args into cls_common structure
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07 09:42:37 -07:00
Jiri Pirko 2572ac53c4 net: sched: make type an argument for ndo_setup_tc
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07 09:42:35 -07:00
Grygorii Strashko a93439cce2 net: ethernet: ti: cpts: fix fifo read in cpts_find_ts
Now the call chain
 cpts_find_ts()
  |- cpts_fifo_read(cpts, CPTS_EV_PUSH)

will stop reading CPTS FIFO if PUSH event is found. But this is not
expected and CPTS FIFI should be completely drained here. This is most
probably copy-paste error and it has no negative impact as CPTS_EV_PUSH
should not be present in FIFO without TS_PUSH request and
cpts_systim_read() and cpts_find_ts() synchronized by spin_lock.

Correct above by calling cpts_fifo_read() with -1 parameter, so it will
read all CPTS event from FIFO.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-01 15:22:55 -07:00
Grygorii Strashko 0d5f54fec0 net: ethernet: ti: cpts: fix tx timestamping timeout
With the low speed Ethernet connection CPDMA notification about packet
processing can be received before CPTS TX timestamp event, which is set
when packet actually left CPSW while cpdma notification is sent when packet
pushed in CPSW fifo.  As result, when connection is slow and CPU is fast
enough TX timestamping is not working properly.

Fix it, by introducing TX SKB queue to store PTP SKBs for which Ethernet
Transmit Event hasn't been received yet and then re-check this queue
with new Ethernet Transmit Events by scheduling CPTS overflow
work more often (every 1 jiffies) until TX SKB queue is not empty.

Side effect of this change is:
 - User space tools require to take into account possible delay in TX
timestamp processing (for example ptp4l works with tx_timestamp_timeout=400
under net traffic and tx_timestamp_timeout=25 in idle).

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-01 15:22:55 -07:00
Grygorii Strashko 999f129289 net: ethernet: ti: cpts: convert to use ptp auxiliary worker
There could be significant delay in CPTS work schedule under high system
load and on -RT which could cause CPTS misbehavior due to internal counter
overflow. Usage of own kthread_worker allows to avoid such kind of issues
and makes it possible to tune priority of CPTS kthread_worker thread on -RT
(thread name "cpts").

Hence, the CPTS driver is converted to use PTP auxiliary worker as PHC
subsystem implements such functionality in a generic way now.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-01 15:22:55 -07:00
Rob Herring f7ce91038d net: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-24 13:41:48 -07:00
Keerthy 070f9c658a net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.

Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.

Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-20 15:28:54 -07:00
David S. Miller b079115937 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
A set of overlapping changes in macvlan and the rocker
driver, nothing serious.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-30 12:43:08 -04:00
Ivan Khoronzhuk 0ccf59ba07 net: ethernet: ti: netcp_ethss: use cpts to check if packet needs timestamping
There is cpts function to check if packet can be timstamped with cpts.
Seems that ptp_classify_raw cover all cases listed with "case".

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-29 12:28:57 -04:00
Ivan Khoronzhuk f44f8417ba net: ethernet: ti: cpsw: fix sw timestamping for non PTP packets
The cpts can timestmap only ptp packets at this moment, so driver
cannot mark every packet as though it's going to be timestamped,
only because h/w timestamping for given skb is enabled with
SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result
outgoing packet is not timestamped at all if it's not PTP and h/w
timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS
only for PTP packets.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-29 12:28:57 -04:00
Ivan Khoronzhuk 98fdd857a3 net: ethernet: ti: cpsw: move skb timestamp to packet_submit
Move sw timestamp function close to channel submit function.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-29 12:28:56 -04:00
Lokesh Vutla b88ff4f8c9 drivers: net: cpsw-common: Fix reading of mac address for am43 SoCs
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.

Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-22 11:14:47 -04:00
yuval.shaia@oracle.com 5514174fe9 net: phy: Make phy_ethtool_ksettings_get return void
Make return value void since function never return meaningfull value

Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13 12:59:06 -04:00
Grygorii Strashko 6d307f6b09 net: ethernet: ti: cpdma: do not enable host error misc irq
CPSW driver does not handle this interrupt, so there are no reasons to enable
it in hardware.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-10 22:10:13 -04:00
Grygorii Strashko e9523a5a32 net: ethernet: ti: cpsw: enable HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter
CPSW driver supports PTP v1 messages, but for unknown reasons this filter
is not advertised. As result,
./tools/testing/selftests/networking/timestamping/timestamping utility
can't be used for testing of CPSW RX timestamping with option
SOF_TIMESTAMPING_RX_HARDWARE, because it uses
HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter.

Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters
in CPSW driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-10 22:10:13 -04:00
Jiri Pirko a5fcf8a6c9 net: propagate tc filter chain index down the ndo_setup_tc call
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-08 09:55:53 -04:00
Miroslav Lichvar e341257548 net: ethernet: update drivers to handle HWTSTAMP_FILTER_NTP_ALL
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.

CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-21 13:37:32 -04:00
Miroslav Lichvar ca9df7ede4 net: netcp: fix check of requested timestamping filter
The driver doesn't support timestamping of all received packets and
should return error when trying to enable the HWTSTAMP_FILTER_ALL
filter.

Cc: WingMan Kwok <w-kwok2@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-15 15:21:03 -04:00
Ivan Khoronzhuk 5b6cb43b4d net: ethernet: ti: netcp_core: return error while dma channel open issue
Fix error path while dma open channel issue. Also, no need to check output
on NULL if it's never returned.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-11 12:39:34 -04:00
Grygorii Strashko 48f5bccc60 net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
When users set flow control using ethtool the bits are set properly in the
CPGMAC_SL MACCONTROL register, but the FIFO depth in the respective Port n
Maximum FIFO Blocks (Pn_MAX_BLKS) registers remains set to the minimum size
reset value. When receive flow control is enabled on a port, the port's
associated FIFO block allocation must be adjusted. The port RX allocation
must increase to accommodate the flow control runout. The TRM recommends
numbers of 5 or 6.

Hence, apply required Port FIFO configuration to
Pn_MAX_BLKS.Pn_TX_MAX_BLKS=0xF and Pn_MAX_BLKS.Pn_RX_MAX_BLKS=0x5 during
interface initialization.

Cc: Schuyler Patton <spatton@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-08 17:33:19 -04:00
Linus Torvalds 8d65b08deb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Millar:
 "Here are some highlights from the 2065 networking commits that
  happened this development cycle:

   1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)

   2) Add a generic XDP driver, so that anyone can test XDP even if they
      lack a networking device whose driver has explicit XDP support
      (me).

   3) Sparc64 now has an eBPF JIT too (me)

   4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
      Starovoitov)

   5) Make netfitler network namespace teardown less expensive (Florian
      Westphal)

   6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)

   7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)

   8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)

   9) Multiqueue support in stmmac driver (Joao Pinto)

  10) Remove TCP timewait recycling, it never really could possibly work
      well in the real world and timestamp randomization really zaps any
      hint of usability this feature had (Soheil Hassas Yeganeh)

  11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
      Aleksandrov)

  12) Add socket busy poll support to epoll (Sridhar Samudrala)

  13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
      and several others)

  14) IPSEC hw offload infrastructure (Steffen Klassert)"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
  tipc: refactor function tipc_sk_recv_stream()
  tipc: refactor function tipc_sk_recvmsg()
  net: thunderx: Optimize page recycling for XDP
  net: thunderx: Support for XDP header adjustment
  net: thunderx: Add support for XDP_TX
  net: thunderx: Add support for XDP_DROP
  net: thunderx: Add basic XDP support
  net: thunderx: Cleanup receive buffer allocation
  net: thunderx: Optimize CQE_TX handling
  net: thunderx: Optimize RBDR descriptor handling
  net: thunderx: Support for page recycling
  ipx: call ipxitf_put() in ioctl error path
  net: sched: add helpers to handle extended actions
  qed*: Fix issues in the ptp filter config implementation.
  qede: Fix concurrency issue in PTP Tx path processing.
  stmmac: Add support for SIMATIC IOT2000 platform
  net: hns: fix ethtool_get_strings overflow in hns driver
  tcp: fix wraparound issue in tcp_lp
  bpf, arm64: fix jit branch offset related to ldimm64
  bpf, arm64: implement jiting of BPF_XADD
  ...
2017-05-02 16:40:27 -07:00
Arnd Bergmann 504926df6d cpsw/netcp: refine cpts dependency
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:

a) configurations that did not already enable PTP_1588_CLOCK will
   now miss the cpts driver

b) when cpts support is disabled, the driver crashes. This is a
   preexisting problem that we did not notice before my patch.

While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.

Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef36234 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-28 15:55:14 -04:00
Ivan Khoronzhuk 799dbe3e1c net: ethernet: ti: netcp_core: remove unused compl queue mapping
This code is unused and probably was unintentionally left while
moving completion queue mapping in submit function.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-25 11:54:47 -04:00
Colin Ian King 11a9ec4330 net: netcp: fix spelling mistake: "memomry" -> "memory"
Trivial fix to spelling mistake in dev_err message and rejoin
line.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-24 13:59:32 -04:00
David S. Miller 6f14f443d3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-06 08:24:51 -07:00
Sekhar Nori 30c57f0734 net: ethernet: ti: cpsw: fix race condition during open()
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().

To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.

This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.

_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.

Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.

Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04 10:33:33 -07:00
Grygorii Strashko 75514b6654 net: ethernet: ti: cpsw: wake tx queues on ndo_tx_timeout
In case, if TX watchdog is fired some or all netdev TX queues will be
stopped and as part of recovery it is required not only to drain and
reinitailize CPSW TX channeles, but also wake up stoppted TX queues what
doesn't happen now and netdevice will stop transmiting data until
reopenned.

Hence, add netif_tx_wake_all_queues() call in .ndo_tx_timeout() to complete
recovery and restore TX path.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-02 19:42:44 -07:00
David S. Miller 16ae1f2236 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/broadcom/genet/bcmmii.c
	drivers/net/hyperv/netvsc.c
	kernel/bpf/hashtab.c

Almost entirely overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-23 16:41:27 -07:00
Arnd Bergmann 07fef36234 cpsw/netcp: cpts depends on posix_timers
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:

drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]

This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.

Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-22 10:56:42 -07:00
Arnd Bergmann be9ca0d33c cpsw/netcp: work around reverse cpts dependency
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:

drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':

As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.

Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-22 10:56:42 -07:00
Amritha Nambiar 56f36acd21 mqprio: Modify mqprio to pass user parameters via ndo_setup_tc.
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.

This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.

Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.

Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-15 15:20:27 -07:00
Ivan Khoronzhuk 9fe9aa0b73 net: ethernet: ti: cpsw: correct ale dev to cpsw
The ale is a property of cpsw, so change dev to cpsw->dev,
aka pdev->dev, to be consistent.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-17 11:12:32 -05:00
David S. Miller 3f64116a83 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2017-02-16 19:34:01 -05:00
Ivan Khoronzhuk d5bc1613d0 net: ethernet: ti: cpsw: use var instead of func for usage count
The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14 22:30:42 -05:00
Ivan Khoronzhuk a60ced990e net: ethernet: ti: cpsw: fix cpsw assignment in resume
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.

Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)

Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14 14:54:19 -05:00
Ivan Khoronzhuk 1bf960502e net: ethernet: ti: cpsw: return NET_XMIT_DROP if skb_padto failed
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-11 21:26:57 -05:00