The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver codes the two address bytes in reverse order when compared to the
other drivers, so make it consistent (and update the keymap, note that the
result is a prefix change from 0x6b86 -> 0x866b, and the latter is pretty
common among the NECX keymaps. While not conclusive, it's still a strong hint
that the change is correct).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bt8xx driver does RC5 decoding for Nebula digi hardware, but includes
some pointless limitations (both start bits must be one, the
device/address/system must be 0x00). Remove those limitations and update
the keymap to use the full RC5 scancode (fortunately the 0x00 address
means that this is perfectly backwards compatible).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API has been replaced with a
standard API there is no reason anymore to keep it in staging.
So (finally!) move it to drivers/media/pci.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
The ZR050_MO_COMP define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on dvb. dvb is initialized at the
beginning of the function to &port->dvb. Since port is dereferenced
prior to the null test, port must be a valid pointer, and
&port->dvb cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CX18_ALSA_DBGFLG_WARN is cut and pasted twice and we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The saa7134 driver uses core-locking, so there is no longer any need
to use the ioctl op instead of the unlocked_ioctl op. This change
was forgotten for the saa7134-empress.c, so fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a few conflicts with older symbols on older kernels so we
have to patch this driver when backporting. Instead just make these
routines specific to the driver.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the saa7134 module is loaded with the saa7134_userptr set to 1,
then USERPTR support is enabled. A check in buffer_prepare
verifies that the pointer is page-aligned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the saa7134 driver to vb2.
Note that while this uses the vb2-dma-sg version, the VB2_USERPTR mode is
disabled. The DMA hardware only supports DMAing full pages, and in the
USERPTR memory model the first and last scatter-gather buffer is almost
never a full page.
In practice this means that we can't use the VB2_USERPTR mode.
This has been tested with raw video, compressed video, VBI, radio, DVB and
video overlays.
Unfortunately, a vb2 conversion is one of those things you cannot split
up in smaller patches, it's all or nothing. This patch switches the whole
driver over to vb2, using the vb2 ioctl and fop helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All dmaqueue's use saa7134_pgtable, so move it into struct saa7134_dmaqueue.
The videobuf_queue priv_data field now points to the dmaqueue struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When ivtv PCM device is accessed at the state where no firmware is
loaded, it oopses like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: [<ffffffffa049a881>] try_mailbox.isra.0+0x11/0x50 [ivtv]
Call Trace:
[<ffffffffa049aa20>] ivtv_api_call+0x160/0x6b0 [ivtv]
[<ffffffffa049af86>] ivtv_api+0x16/0x40 [ivtv]
[<ffffffffa049b10c>] ivtv_vapi+0xac/0xc0 [ivtv]
[<ffffffffa049d40d>] ivtv_start_v4l2_encode_stream+0x19d/0x630 [ivtv]
[<ffffffffa0530653>] snd_ivtv_pcm_capture_open+0x173/0x1c0 [ivtv_alsa]
[<ffffffffa04526f1>] snd_pcm_open_substream+0x51/0x100 [snd_pcm]
[<ffffffffa0452853>] snd_pcm_open+0xb3/0x260 [snd_pcm]
[<ffffffffa0452a37>] snd_pcm_capture_open+0x37/0x50 [snd_pcm]
[<ffffffffa033f557>] snd_open+0xa7/0x1e0 [snd]
[<ffffffff8118a628>] chrdev_open+0x88/0x1d0
[<ffffffff811840be>] do_dentry_open+0x1de/0x270
[<ffffffff81193a73>] do_last+0x1c3/0xec0
[<ffffffff81194826>] path_openat+0xb6/0x670
[<ffffffff81195b65>] do_filp_open+0x35/0x80
[<ffffffff81185449>] do_sys_open+0x129/0x210
[<ffffffff815b782d>] system_call_fastpath+0x1a/0x1f
This patch adds the check of firmware at PCM open callback like other
open callbacks of this driver.
Bugzilla: https://apibugzilla.novell.com/show_bug.cgi?id=875440
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The else statement here is not aligned with the correct if statement.
I think the code works as intended and it's just the indenting which is
wrong. Also kernel style says we should use curly braces here so I have
added those.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Changeset 15e64f0dde broke compilation on several archs, as it
forgot to include vmalloc.h.
drivers/media/pci/saa7134/saa7134-alsa.c: In function ‘saa7134_alsa_dma_init’:
CC [M] drivers/media/rc/keymaps/rc-behold-columbus.o
drivers/media/pci/saa7134/saa7134-alsa.c:283:2: error: implicit declaration of function ‘vmalloc_32’ [-Werror=implicit-function-declaration]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:283:13: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:2: error: implicit declaration of function ‘vzalloc’ [-Werror=implicit-function-declaration]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:14: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:310:2: error: implicit declaration of function ‘vfree’ [-Werror=implicit-function-declaration]
vfree(dma->sglist);
Add it to avoid such breakages.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is already available from saa7134_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't calculate this for every buffer, store it globally instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This will make the next patch a bit easier to read.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa7134-alsa used low-level videobuf functions to allocate and sync
DMA buffers. Replace this with saa7134-specific code. These functions
will not be available when we convert to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just white space and coding style changes to reduce the noise in the
following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.
A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.
The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Do not attempt to reload the tuner modules when resuming after a suspend.
This triggers a WARN_ON in kernel/kmod.c:148 __request_module.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69581.
This has always been wrong, but it was never noticed until the WARN_ON
was added in 3.9.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.9 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Static checkers complain about the inconsistent NULL check here.
There is an unchecked dereference of "input->fe" in the call to
tuner_attach_tda18271() and there is a second unchecked dereference a
couple lines later when we do:
input->fe2->tuner_priv = input->fe->tuner_priv;
But actually "intput->fe" can't be NULL because if demod_attach_drxk()
fails to allocate it, then we would have return an error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ARRAY_SIZE(buf) (8 elements) was intended instead of sizeof(buf) (16
bytes). But this is just a sanity check and the callers always pass
valid values so this doesn't cause a problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New board addition. No other changes.
[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When tuning to 10818V on Astra 28E2, the system tunes to 11343V
instead. This is a regression in the S471 driver introduced with the
changeset: b43ea8068d [media] cx23885:
Fix TeVii S471 regression since introduction of ts2020.
Suggested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Joakim Hernberg <jhernberg@alchemy.lu>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I am no longer available at the kernellabs.com or m1k.net email
addresses. Update each instance of my email to my linuxtv.org
account.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is required so that we give up the last reference to the device.
Remove the kfree() because the put_device() call will actually call
release_sub_device which in turn kfrees the device.
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
You can set this through sysfs, so don't mix the two.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no controls for the radio node, so just drop support for this ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver is independent from saa7134, so there is no reason why this
shouldn't be in media/i2c like all other i2c media drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The saa7134 driver is now converted to the control framework, so drop the
control compat code in saa6752hs.c.
Also add 'const' to several static arrays.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
NO_SYNC was meant for DVB and shouldn't be used anymore.
In this case NO_SIGNAL is a good alternative.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The empress video node can share resource management with the normal
video nodes, thus allowing for code sharing and making the empress node
non-exclusive.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the saa7134_fh struct for the empress video node as well, drop the dev
pointer from that struct since we can use drvdata for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video and empress nodes can share various ioctls.
Drop the input/std ioctls from the radio node (out of spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These fields are global, not per-filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It upsets static checkers when we don't check for allocation failure. I
moved the memset() of "tv" earlier so we don't use uninitialized data on
error.
Fixes: 1d212cf0c2 ('[media] cx18: struct i2c_client is too big for stack')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We had set the pci drvdata in cx88_audio_initdev() as a type of
struct snd_card, so cx88_audio_finidev() should used it as the
same type too.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of error, the function kthread_run() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The no_video flag was checked in all other cases except one. Calling
v4l2_ctrl_handler_setup() if no_video is 1 will crash.
This wasn't noticed before since there are only two card types that
set no_video to 1, so this type of hardware is quite rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lorenz Röhrl <sheepshit@gmx.de>
Tested-by: Lorenz Röhrl <sheepshit@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/cx23885/cimax2.c:149:1: warning: 'netup_write_i2c' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/ttpci/av7110_hw.c:510:1: warning: 'av7110_fw_cmd' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum fw command size
is 6 + 2, as checked using:
$ git grep -A1 av7110_fw_cmd drivers/media/pci/ttpci/
So, use 8 for the buffer size.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/pci/cx18/cx18-driver.c: In function 'cx18_read_eeprom':
drivers/media/pci/cx18/cx18-driver.c:357:1: warning: the frame size of 1072 bytes is larger than 1024 bytes [-Wframe-larger-than=]
That happens because the routine allocates 256 bytes for an eeprom buffer, plus
the size of struct i2c_client, with is big.
Change the logic to dynamically allocate/deallocate space for struct i2c_client,
instead of using the stack.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver uses virt_to_bus() with is deprecated on Alpha:
drivers/media/pci/zoran/zoran_device.c: In function 'zr36057_set_vfe':
drivers/media/pci/zoran/zoran_device.c:451:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_device.c:453:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_device.c: In function 'zr36057_set_jpg':
drivers/media/pci/zoran/zoran_device.c:796:2: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c: In function 'v4l_fbuffer_alloc':
drivers/media/pci/zoran/zoran_driver.c:241:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:245:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c: In function 'jpg_fbuffer_alloc':
drivers/media/pci/zoran/zoran_driver.c:334:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:347:5: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:366:6: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
As we're not even sure if it works on Alpha, better to just disable its compilation there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
i2c_adap is a field of a struct and will always be allocated so
its address will never be null.
Suggested by coccinelle, manually verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/pci/cx25821/cx25821-cards.c:49:20: warning: symbol 'cx25821_bcount' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-video-upstream.c:162:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:163:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:164:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:165:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-medusa-video.h:43:16: warning: symbol '_num_decoders' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:44:16: warning: symbol '_num_cameras' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:46:14: warning: symbol '_video_standard' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:47:5: warning: symbol '_display_field_cnt' was not declared. Should it be static?
After analyzing the last four warnings carefully it became clear that these
variables were really completely unused. As a result of that the call to
medusa_set_decoderduration() is now dubious since the duration is always 0.
Without documentation, however, I can't tell what the right value is.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
module_pci_driver removes some boilerplate and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested:
Composite: http://imgur.com/Rb1TCF3
TV: http://imgur.com/KNrfsmv
Firmware used: xc3028-v27.fw
Not tested: audio, component, s-video, mpeg2 encoder, FM radio.
For audio, it uses an CD style cable to connect to the analog "CD_IN" on the motherboard.
I didn't found how to unmute it (alsamixer do not show an CD or AUX channel).
Signed-off-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
pm_qos_remove_request was not called on video_release, resulting in the PM
core's list of requests being corrupted when the file handle was freed.
This has no immediate symptoms, but later in operation, the kernel will
panic as the PM core dereferences a dangling pointer.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cards using the wm8775 specify that in their card struct. Those that do not
use it leave the audio_chip field to 0. Unfortunately, the CX88_AUDIO_WM8775
enum is 0 as well, so boards that do not have the wm8775 still try to load
and use that driver. Change it to 1 to fix this.
This regression was introduced in commit facd23664f.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
As reported by Jim Davis <jim.epost@gmail.com>:
randconfig build error with next-20130813, in drivers/media/pci/cx88,
when:
CONFIG_VIDEO_CX88=y
CONFIG_VIDEO_CX88_BLACKBIRD=m
CONFIG_VIDEO_CX88_DVB=y
CONFIG_VIDEO_CX88_VP3054=m
CONFIG_VIDEO_CX88_MPEG=y
LD init/built-in.o
drivers/built-in.o: In function `cx8802_dvb_remove':
cx88-dvb.c:(.text+0x3a9914): undefined reference to `vp3054_i2c_remove'
drivers/built-in.o: In function `cx8802_dvb_probe':
cx88-dvb.c:(.text+0x3a9c4b): undefined reference to `vp3054_i2c_probe'
make: *** [vmlinux] Error 1
That happens because the vp3054 symbols aren't available builtin.
So, make it builtin, if CX88_DVB=y, or module otherwise, if this
support is selected.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hi,
Handling the AV Core/IR interrupts schedules its workqueue but
the schedule_work function returns false if @work was already on the
kernel-global workqueue and true otherwise.
Printing an error message if @work wasn't in the queue is wrong.
Regards,
Luis
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those boards were missing the ISDB-T support.
Most of the work on this patch were done by Alfredo.
My work here were to port this patch from Kernel 3.2 to upstream,
fix the issue caused by the set_frontend bad hook, and add the
Kconfig bits.
Tested on a X8502 board rebranded as:
"Leadership - Placa PCI-e de Captura de Vídeo Híbrida" - product code 3800.
Thanks-to: Alfredo Delaiti <alfredodelaiti@netscape.net>
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the frontend drivers got converted to DVBv5 API, the original
hook that tracked when a frontend is set got removed, being replaced
by an approach that would use the gate control. That doesn't work
fine with some boards. Also, the code were called more times than
desired.
Replace it by a logic that will hook the dvb set_frontend ops,
with works with both DVBv3 and DVBv5 calls.
Tested on a Mygica X8502 OEM board.
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Apparently the Flatiron genereates an interrupt after the built-in self
test for each of its left and right channels has completed.
Apparently Conexant wire-OR'ed the Flatiron's interrupt output with the
interrupt output of the CX23885 A/V core.
Those interrupts need to be handled, otherwise, they generate an
interrrupt request storm.
So:
- Add flatiron readreg and writereg functions prototypes
on a new header file;
- Modify the av interrupt handler to cleanup flatiron IRQs if no other
interrupt handling happens.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Patch to make TeVii S471 cards use the ts2020 tuner, since ds3000 driver no
longer contains tuning code.
Signed-off-by: Johannes Koch <johannes@ortsraum.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int)
in struct bttv as char *.
Remove this hack and add a proper sw_status array to struct bttv instead.
This is a a preparation to remove mbox_we.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the workqueue creation interfaces that do not expect format strings,
make sure they cannot accidently be parsed that way. Additionally, clean
up calls made with a single parameter that would be handled as a format
string. Many callers are passing potentially dynamic string content, so
use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
build/media_build/v4l/saa7164-core.c: In function 'saa7164_initdev':
build/media_build/v4l/saa7164-core.c:1192:6: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized]
int err, i;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88 driver has one v4l2_device, but the video nodes are owned by two
different PCI busses. So the dev_parent pointer should be set to the correct
parent bus, otherwise sysfs won't show the correct device hierarchy.
This broke starting in 3.6 after a driver change, so this patch resurrects
the correct behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver did not yet support struct v4l2_device, so add it. This
make it possible to replace the deprecated parent field with the
v4l2_dev field, allowing the eventual removal of the parent field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the register is aligned to a dword, otherwise the read could
read out-of-range data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove g_chip_ident from cx88. Also remove the v4l2-chip-ident.h include.
The board code used defines from v4l2-chip-ident.h to tell the driver which
audio chip is used. Replace this with a cx88-specific enum.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
As USB/PCI/MEDIA_SUPPORT dependencies can be tristate, we can't
simply make the bool menu to be dependent on it. Everything below
the menu should also depend on it, otherwise, we risk to allow
building them with 'y', while only 'm' would be supported.
So, add an IF just before everything below, in order to avoid
such risks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix uninitialized fields and a missing TRY_FMT implementation in saa6752hs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- map overlay format values to the supported ranges
- set colorspace
- zero priv field
- fix cliplist handling
- fix field handling
- initialize ovbuf values
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a global field, not a per-filehandle field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These fields are global, not per-filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is global data, not per-filehandle data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This information is already available in vfl_type in video_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, if the norm set is V4L2_STD_ALL, then autodetect the current
standard and use that. This is non-standard behavior, and in fact it hasn't
worked for a very long time: before s_std is called in this driver, the
v4l2 core will mask it with the tvnorms field. So even if the application
passes V4L2_STD_ALL, the zoran driver will always see a subset of that.
Since nobody ever complained about this we just remove this non-standard
functionality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AND the standard mask with the detected standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since this driver properly implements g_std, the current_norm field is
actually unused anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of current_norm can be dropped. The g_std ioctl was already
implemented, so current_norm didn't do anything useful anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
current_norm is deprecated. Replace it by g_std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the register is aligned to a dword, otherwise the range check
could fail since it assumes dword alignment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the register is aligned to a dword, otherwise the range check
could fail since it assumes dword alignment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This op and the v4l2-chip-ident.h header are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace g_chip_ident by g_chip_info. Note that the IR support is implemented
as a subdev, so this part no longer needs to be handled as a 'bridge' chip.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
g_chip_ident was used to determine if a saa7114 or saa7115 was used. Instead
just check the subdev name.
After that the g_chip_ident function can be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The av-core is really a subdev, so there is no need anymore to act as if it
is a 'second' bridge chip.
As a result of this the g_chip_ident implementation can be completely dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a NULL pointer deference when loading the cx88_dvb module for a
Hauppauge HVR4000.
The bugzilla bug report is here:
https://bugzilla.kernel.org/show_bug.cgi?id=56271
The cause is that the wm8775 is optional, so even though the board info says
there is one, it doesn't have to be there. Checking whether the module was
actually loaded is much safer.
Note that this driver is quite buggy when it comes to unloading and reloading
modules. Unloading cx8800 and reloading it again will still cause a crash,
most likely because either the i2c bus isn't unloaded at the right time and/or
the v4l2_device_unregister isn't called at the right time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Sebastian Frei <sebastian@familie-frei.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the enum values have changed recently, the comments are void.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: mjpeg-users@lists.sourceforge.net
cc: linux-media@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull media update from Mauro Carvalho Chehab:
- OF documentation and patches at core and drivers, to be used by for
embedded media systems
- some I2C drivers used on go7007 were rewritten/promoted from staging:
sony-btf-mpx, tw2804, tw9903, tw9906, wis-ov7640, wis-uda1342
- add fimc-is driver (Exynos)
- add a new radio driver: radio-si476x
- add a two new tuners: r820t and tuner_it913x
- split camera code on em28xx driver and add more models
- the cypress firmware load is used outside dvb usb drivers. So, move
it to a common directory to make easier to re-use it
- siano media driver updated to work with sms2270 devices
- several work done in order to promote go7007 and solo6x1x out of
staging (still, there are some pending issues)
- several API compliance fixes at v4l2 drivers that don't behave as
expected
- as usual, lots of driver fixes, improvements, cleanups and new device
addition at the existing drivers.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (831 commits)
[media] cx88: make core less verbose
[media] em28xx: fix oops at em28xx_dvb_bus_ctrl()
[media] s5c73m3: fix indentation of the help section in Kconfig
[media] cx25821-alsa: get rid of a __must_check warning
[media] cx25821-video: declare cx25821_vidioc_s_std as static
[media] cx25821-video: remove maxw from cx25821_vidioc_try_fmt_vid_cap
[media] r820t: Remove a warning for an unused value
[media] dib0090: Fix a warning at dib0090_set_EFUSE
[media] dib8000: fix a warning
[media] dib8000: Fix sub-channel range
[media] dib8000: store dtv_property_cache in a temp var
[media] dib8000: warning fix: declare internal functions as static
[media] r820t: quiet gcc warning on n_ring
[media] r820t: memory leak in release()
[media] r820t: precendence bug in r820t_xtal_check()
[media] videodev2.h: Remove the unused old V4L1 buffer types
[media] anysee: Grammar s/report the/report to/
[media] anysee: Initialize ret = 0 in anysee_frontend_attach()
[media] media: videobuf2: fix the length check for mmap
[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0
...
Along the time, several debug messages were added at cx88-cards.
While those are still useful to track some troubles with
tuners, they're too verbose:
[ 5768.281801] cx88[0]: Calling XC2028/3028 callback
[ 5768.287388] cx88[0]: Calling XC2028/3028 callback
[ 5768.292575] cx88[0]: Calling XC2028/3028 callback
[ 5768.299408] cx88[0]: Calling XC2028/3028 callback
[ 5768.306244] cx88[0]: Calling XC2028/3028 callback
...
and, most of the time, useless.
So, disable them, except if core_debug modprobe parameter
is used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hole reason for __must_check is to not ignore an error.
However, a "ret" value is used at cx25821 just to avoid the
Kernel compilation to compain about it.
That, however, produces another warning (with W=1):
drivers/media/pci/cx25821/cx25821-alsa.c: In function 'cx25821_audio_fini':
drivers/media/pci/cx25821/cx25821-alsa.c:727:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
With the current implementation of driver_for_each_device() and
cx25821_alsa_exit_callback(), there's actually just one
very unlikely condition where it will currently produce
an error: if driver_find() returns NULL.
Ok, there's not much that can be done, as it is on a driver's
function that returns void, but it can at least print some message
if the error happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warning:
drivers/media/pci/cx25821/cx25821-video.c: At top level:
drivers/media/pci/cx25821/cx25821-video.c:766:5: warning: no previous prototype for 'cx25821_vidioc_s_std' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After cx25821-video cleanup, this var is not used anymore:
drivers/media/pci/cx25821/cx25821-video.c: In function 'cx25821_vidioc_try_fmt_vid_cap':
drivers/media/pci/cx25821/cx25821-video.c:591:15: warning: variable 'maxw' set but not used [-Wunused-but-set-variable]
as the code now checks the max width as the default case for the
range check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Legacy PCI suspend-resume handlers are called with interrupts enabled.
But cx8800_suspend/cx8800_resume and
cx8802_suspend_common/cx8802_resume_common use spin_lock/spin_unlock
functions to acquire dev->slock, while the same lock is acquired in the
corresponding irq-handlers: cx8800_irq and cx8802_irq.
That means a deadlock is possible if an interrupt happens while suspend
or resume owns the lock. The patch replaces spin_lock/spin_unlock with
spin_lock_irqsave/spin_unlock_irqrestore.
Found by Linux Driver Verification project (linuxtesting.org).
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Fengguang Wu <fengguang.wu@intel.com>:
> drivers/media/pci/sta2x11/sta2x11_vip.c: In function 'sta2x11_vip_init_one':
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:2: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1314:15: warning: assignment makes pointer from integer without a cast [enabled by default]
> drivers/media/pci/sta2x11/sta2x11_vip.c:1330:2: error: implicit declaration of function 'i2c_put_adapter' [-Werror=implicit-function-declaration]
And also:
> warning: (STA2X11_VIP) selects VIDEO_ADV7180 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_V4L2 && I2C)
> drivers/media/i2c/adv7180.c: In function '__adv7180_status':
> drivers/media/i2c/adv7180.c:194:2: error: implicit declaration of function 'i2c_smbus_read_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_s_routing':
> drivers/media/i2c/adv7180.c:251:2: error: implicit declaration of function 'i2c_smbus_write_byte_data' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: In function 'adv7180_probe':
> drivers/media/i2c/adv7180.c:551:2: error: implicit declaration of function 'i2c_check_functionality' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c:554:2: error: implicit declaration of function 'i2c_adapter_id' [-Werror=implicit-function-declaration]
> drivers/media/i2c/adv7180.c: At top level:
> drivers/media/i2c/adv7180.c:663:1: warning: data definition has no type or storage class [enabled by default]
> drivers/media/i2c/adv7180.c:663:1: warning: type defaults to 'int' in declaration of 'module_i2c_driver' [-Wimplicit-int]
> drivers/media/i2c/adv7180.c:663:1: warning: parameter names (without types) in function declaration [enabled by default]
> drivers/media/i2c/adv7180.c:649:26: warning: 'adv7180_driver' defined but not used [-Wunused-variable]
This is due to the lack of I2C support:
...
> CONFIG_I2C is not set
...
So, Make sure that sta2x11_vip depends on I2C.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE. Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio output is currently not used as this should be rewritten as an
alsa driver. For the time being remove this source from the Makefile.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ideally this should be implemented with vb2, but it'll do for now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx25821-video-upstream_ch2.c/h is practically identical to cx25821-video-upstream.c/h
so add support for ch2 into cx25821-video-upstream.c instead.
After this we can replace the custom ioctls with a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No other changes, just function reordering.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop the custom ioctls and enable the video output nodes again, this time
using standard ioctls.
The next step will be to provide a proper write() interface.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not have subdevices, so why call subdev ops? After
removing that it became apparent that only Composite is supported as
input, so remove also any reference to other inputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No idea why these custom ioctls exist: they have perfectly normal v4l2
counterparts which are already implemented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fill in colorspace
- zero priv
- delete unsupported formats
- fix field handling
- s_std should update width/height
- proper mapping of width/height to valid resolutions
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now possible to remove cx25821_fh and replace it with v4l2_fh,
which in turn makes event handling and core prio handling possible.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just remember which filehandle is streaming instead of using complicated
resource masks.
After this patch we can replace cx25821_fh with v4l2_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not a per-filehandle object, it's a per-channel object.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to replace .ioctl with .unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2 core already has support for debugging ioctls/file operations.
No need to do that again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Embed the video_device struct instead of allocating it.
Remove some of the annoying and ugly kernel messages shown during
loading and unloading of the module.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver doesn't use DVB, RC, cx25840 or tveeprom.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver does not implement cropping, so remove the cropping ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A lot of functions and variables were external when they really can be
declared as static.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s_input implementation allowed input 1 even if that didn't exist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device list is not necessary. The kernel already has all that information,
so just use that instead.
Also remove a bogus refcount and some dead 'private_free' code in the alsa driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And get rid of the channel0-11 external pointers and two more unused fields
in cx25821.h.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
log_status shouldn't print LOG STATUS lines, the core does that already.
Fix querycap version number and add device_caps support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do some spring cleaning:
- there are no board defines with tuners, so remove bogus tuner support.
- tv standard handling has nothing to do with tuners, so keep that.
- replace the deprecated current_norm by g_std.
- querystd isn't implemented, so remove the ioctl.
- remove a bunch of unused fields in cx25821.h
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device does not support radio or vbi, so remove anything referring
to that.
In addition, the driver created an 'video ioctl' node, which was unused and
was effectively identical to the first video node.
This bogus video node is now removed, leaving us with 8 video capture nodes
and 2 video output nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx25821/cx25821-video.c: In function ‘cx25821_video_register’:
drivers/media/pci/cx25821/cx25821-video.c:518:1: warning: the frame size of 1600 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Fixed by just making the struct video_device template static const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Skip the audio channel when registering the video nodes. This fixes a bug
where that incorrectly registered 'video' node was never unregistered.
Note: this bug only surfaces if the video output nodes are enabled again
after the previous patch disabled them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25821 driver has support for one audio output channel and two video
output channels.
This is implemented in a very ugly and very evil way through a custom ioctl
that passes the filename of a file containing the video data, which is then
read by the driver itself using vfs.
There are a number of problems with this:
1) it's very ugly and very evil (I can't say that often enough).
2) V4L2 supports video output, so why not use that?
3) it's very buggy, closing the filehandle through which you passed the ioctl
will oops the kernel.
4) it's a nasty security leak since this allows you to load any file in the
system as a video or audio source, so in theory you can output /etc/passwd
to audio or video out and record & decode it on another device.
Because of all these issues we no longer register those output video nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: clear reserved space of VBI
structure to make sure no garbage is left there
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_parm function
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove empty g_audio and s_audio
functions and don't set audioset in enum_input
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: return real frequency range in
g_tuner and fail in s_tuner for non-zero tuner
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: don't cache frequency in
s_frequency/g_frequency but return real one instead
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: remove broken priority handling
and use v4l2_fh instead
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
[hans.verkuil@cisco.com: fixed a merge conflict in saa7134.h]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: filter audio modes that came from
tuner - keep only MONO/STEREO in radio mode
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make saa7134 driver more V4L2 compliant: implement V4L2_CAP_DEVICE_CAPS support
and fix all capabilities problems reported by v4l2-compliance.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use enum instead of magic values for LNA config in tda8290.
Update tda827x, tda18271 and saa7134 to use the enum too.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add AverMedia AverTV Satellite Hybrid+FM (A706) card to saa7134 driver.
Working: analog inputs, TV, FM radio and IR remote control.
Untested: DVB-S.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config looks like a hack that was added to tuner-core to allow some
configuration of TDA8290 tuner (it's not used by any other driver).
But with the new configuration options of tda8290 driver (no_i2c_gate
and std_map), it's no longer sufficient.
Change config to be void * instead, which allows passing tuner-dependent
config struct to drivers.
Also update saa7134 driver to reflect this change (no other driver uses this).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge Nova-S-Plus DVB-S model 92001 does not lock on horizontal
polarisation. According with the info provided at the BZ, model
92002 does.
The difference is that, on model 92001, the tone select is done via
isl6421, while, on other devices, this is done via cx24123 code.
This patch adds a way to override the demod's set_tone at isl6421
driver. In order to avoid regressions, the override is enabled
only for cx88 Nova S plus model 92001. For all other models and
devices, the set_tone is provided by the demod driver.
Patch originally proposed at bz@9476[1] by Michel Meyers and
John Donoghue but applying the original patch would break support
for all other devices based on isl6421.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=9476
Tested-by: Adam Sampson <ats@offog.org>
Tested-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"enum dmx_ts_pes" and "typedef enum dmx_pes_type_t" are just the
same enum declared twice, since Kernel (2.6.12). There's no reason
to duplicate it there, and sparse complains about that:
drivers/media/dvb-core/dmxdev.c:600:55: warning: mixing different enum types
So, remove the internal define, keeping just the external one.
Internally, use only "enum dmx_ts_pes", as it is too late to drop
dmx_pes_type_t from the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into patchwork
Linux 3.9-rc5
* tag 'v3.9-rc5': (1080 commits)
Linux 3.9-rc5
Revert "lockdep: check that no locks held at freeze time"
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
PNP: List Rafael Wysocki as a maintainer
rbd: don't zero-fill non-image object requests
ia64 idle: delete stale (*idle)() function pointer
Btrfs: don't drop path when printing out tree errors in scrub
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
mg_disk: fix error return code in mg_probe()
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
...
Since commit a1fd287780c8e91fed4957b30c757b0c93021162:
"[media] bttv-driver: fix two warnings"
cropcap.defrect.height and cropcap.bounds.height for the PAL entry are 32
resp 30 pixels too large, if a userspace app (ie xawtv) actually tries to use
the full advertised height, the resulting image is broken in ways only a
screenshot can describe.
The cause of this is the fix for this warning:
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: initialized field overwritten [-Woverride-init]
In this chunk of the commit:
@@ -301,11 +301,10 @@ const struct bttv_tvnorm bttv_tvnorms[] = {
/* totalwidth */ 1135,
/* sqwidth */ 944,
/* vdelay */ 0x20,
- /* sheight */ 576,
- /* videostart0 */ 23)
/* bt878 (and bt848?) can capture another
line below active video. */
- .cropcap.bounds.height = (576 + 2) + 0x20 - 2,
+ /* sheight */ (576 + 2) + 0x20 - 2,
+ /* videostart0 */ 23)
},{
.v4l2_id = V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR,
.name = "NTSC",
Which replaces the overriding of cropcap.bounds.height initialization outside
of the CROPCAP macro (which also initializes it), with passing a
different sheight value to the CROPCAP macro.
There are 2 problems with this warning fix:
1) The sheight value is used twice in the CROPCAP macro, and the old code
only changed one resulting value.
2) The old code increased the .cropcap.bounds.height value (and did not
touch the .cropcap.defrect.height value at all) by 2, where as the fixed
code increases it by 32, as the fixed code passes (576 + 2) + 0x20 - 2
to the CROPCAP macro, but the + 0x20 - 2 is already done by the macro so
now is done twice for .cropcap.bounds.height, and also is applied to
.cropcap.defrect.height where it should not be applied at all.
This patch fixes this by adding an extraheight parameter to the CROPCAP entry
and using it for the PAL entry.
Cc: stable@kernel.org # For Kernel 3.8
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ivtv_itvc function receives a pointer to v4l2_dbg_register. When we
add const to that pointer in the s_register case we will run into a problem
here since this common function would discard const in that case. So
change this function so it receives the address and a pointer to a value.
In addition we now set the size field in the g_register function which is
where it belongs.
This will simplify the next patch where const will be added to s_register.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, this has been done implicitly for video device nodes by calling
set_input() (which calls audio_input() and also modified the mute
setting).
Since input and mute setting are now untangled (as much as possible), we need to
apply the mute setting with an explicit call to audio_mute().
Also apply the mute setting when the radio device node gets opened.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split function audio_mux():
move the mute setting part to function audio_mute() and the input setting part
to function audio_input().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the GPIO part of function audio_mux() to a separate function
audio_mux_gpio().
This prepares the code for the next patch which will separate mute and input
setting.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'audio_input' better describes the meaning of this field.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can't and do not save the mute setting in function audio_mux(), so we
should also not save the input in this function for consistency.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are cases where we want to call audio_mux() without changing the value of
the v4l2 mute control, for example
- mute mute on last close
- mute on device probing
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function audio_mux() actually deals with two types of mute: gpio mute and
subdevice muting.
This patch claryfies the meaning of these values, but mainly prepares the code for
the next patch.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm pasting the original code and my proposal on the commit message for
make it easy to compare the two versions.
Line 62 of cx25821-audio-upstream.h contains:
char *_defaultAudioName = "/root/audioGOOD.wav";
Original code after replace kmemdup for kstrdup, and after fix return error
code:
if (dev->input_audiofilename) {
dev->_audiofilename = kstrdup(dev->input_audiofilename,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
/* Default if filename is empty string */
if (strcmp(dev->input_audiofilename, "") == 0)
dev->_audiofilename = "/root/audioGOOD.wav";
} else {
dev->_audiofilename = kstrdup(_defaultAudioName,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
}
Code proposed in this patch:
if ((dev->input_audiofilename) &&
(strcmp(dev->input_audiofilename, "") != 0))
dev->_audiofilename = kstrdup(dev->input_audiofilename,
GFP_KERNEL);
else
dev->_audiofilename = kstrdup(_defaultAudioName,
GFP_KERNEL);
if (!dev->_audiofilename) {
err = -ENOMEM;
goto error;
}
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Like init_bttv_i2c(), fini_bttv_i2c() belongs to bttv-i2c.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Request module ir-kbd-i2c if an i2c ir decoder is detected.
Tested with device "Hauppauge WinTV Theatre" (model 37284 rev B421).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Härdeman
