Crucial M550 may cause data corruption on queued trims and is
blacklisted. The pattern used for it fails to match 1TB one as the
capacity section will be four chars instead of three. Widen the
pattern.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Charles Reiss <woggling@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81071
Cc: stable@vger.kernel.org
The function may be useful for other drivers, so export it. (Suggested
by Tejun Heo.)
Note that I inverted the return value of glob_match; returning true on
match seemed to make more sense.
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2 ("libata/ahci: accommodate tag ordered controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Queued trim only works for some users with MU05 firmware. Revert to
blacklisting all firmware versions.
Introduced by commit d121f7d0cb ("libata: Update queued trim blacklist
for M5x0 drives") which this effectively reverts, while retaining the
blacklisting of M550.
See
https://bugzilla.kernel.org/show_bug.cgi?id=71371
for reports of trouble with MU05 firmware.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
When a ZPODD device is unbound via sysfs, the ACPI notify handler
is not removed. This causes panics as observed in Bug #74601. The
panic only happens when the wake happens from outside the kernel
(i.e. inserting a media or pressing a button). Add a loop to
ata_port_detach which loops through the port's devices and checks
if zpodd is enabled, if so call zpodd_exit.
Cc: stable@vger.kernel.org
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Crucial/Micron M500 drives properly support queued DSM TRIM starting
with firmware MU05. Update the blacklist so we only disable queued trim
for older firmware releases.
Early M550 series drives suffer from the same issue as M500. A bugfix
firmware is in the pipeline but not ready yet. Until then, blacklist
queued trim for M550.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Chris Samuel <chris@csamuel.org>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata updates from Tejun Heo:
"A lot of activities on libata side this time.
- A lot of changes around ahci. Various embedded platforms are
implementing ahci controllers. Some were built atop ahci_platform,
others were doing their own things. Hans made some structural
changes to libahci and librarized ahci_platform so that ahci
platform drivers can share more common code. A couple platform
drivers are added on top of that and several are added to replace
older drivers which were doing their own things (older ones are
scheduled to be removed).
- Dan finishes the patchset to make libata PM operations
asynchronous. Combined with one patch being routed through scsi,
this should speed resume measurably.
- Various fixes and cleanups from Bartlomiej and others"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (61 commits)
ata: fix Marvell SATA driver dependencies
ata: fix ARASAN CompactFlash PATA driver dependencies
ata: remove superfluous casts
ata: sata_highbank: remove superfluous cast
ata: fix Calxeda Highbank SATA driver dependencies
ata: fix R-Car SATA driver dependencies
ARM: davinci: da850: update SATA AHCI support
ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller
ata: move library code from ahci_platform.c to libahci_platform.c
ata: ahci_platform: fix ahci_platform_data->suspend method handling
libata: remove unused ata_sas_port_async_resume() stub
libata.h: add stub for ata_sas_port_resume
libata: async resume
libata, libsas: kill pm_result and related cleanup
ata: Fix compiler warning with APM X-Gene host controller driver
arm64: Add APM X-Gene SoC AHCI SATA host controller DTS entries
ata: Add APM X-Gene SoC AHCI SATA host controller driver
Documentation: Add documentation for the APM X-Gene SoC SATA host controller DTS binding
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
ata: ahci_sunxi: fix code formatting
...
Improve overall system resume time by making libata link recovery
actions asynchronous relative to other resume events.
Link resume operations are performed using the scsi_eh thread, so
commands, particularly the sd resume start/stop command, will be held
off until the device exits error handling. Libata already flushes eh
with ata_port_wait_eh() in the port teardown paths, so there are no
concerns with async operation colliding with the end-of-life of the
ata_port object. Also, libata-core is already careful to flush
in-flight pm operations before another round of pm starts on the given
ata_port.
Reference: https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach
Cc: Len Brown <len.brown@intel.com>
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
[djbw: rebase on cleanup patch, changelog wordsmithing]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun says:
"At least for libata, worrying about suspend/resume failures don't make
whole lot of sense. If suspend failed, just proceed with suspend. If
the device can't be woken up afterwards, that's that. There isn't
anything we could have done differently anyway. The same for resume, if
spinup fails, the device is dud and the following commands will invoke
EH actions and will eventually fail. Again, there really isn't any
*choice* to make. Just making sure the errors are handled gracefully
(ie. don't crash) and the following commands are handled correctly
should be enough."
The only libata user that actually cares about the result from a suspend
operation is libsas. However, it only cares about whether queuing a new
operation collides with an in-flight one. All libsas does with the
error is retry, but we can just let libata wait for the previous
operation before continuing.
Other cleanups include:
1/ Unifying all ata port pm operations on an ata_port_pm_ prefix
2/ Marking all ata port pm helper routines as returning void, only
ata_port_pm_ entry points need to fake a 0 return value.
3/ Killing ata_port_{suspend|resume}_common() in favor of calling
ata_port_request_pm() directly
4/ Killing the wrappers that just do a to_ata_port() conversion
5/ Clearly marking the entry points that do async operations with an
_async suffix.
Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We're now blacklisting "Crucial_CT???M500SSD1" and
"Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is
about the same devices as the crucial branded ones. Let's merge the
two Crucial M500 entries and widen the match to
"Crucial_CT???M500SSD*" so that we don't have to fiddle with new
entries for similar devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Via commit 87809942d3 "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901,
we need to also add firmware revision 2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Queued TRIM commands cause problems and silent file system corruption
on Crucial M500 SSDs. This patch disables them for the mSATA model of
the drive.
Signed-off-by: Marios Andreopoulos <opensource@andmarios.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # 3.12+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
We've received multiple reports in Fedora via (BZ 907193)
that the Seagate Momentus SpinPoint M8 errors out when enabling AA:
[ 2.555905] ata2.00: failed to enable AA (error_mask=0x1)
[ 2.568482] ata2.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Nicholas <arealityfarbetween@googlemail.com>
Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
After commit bcdde7e221 (sysfs: make __sysfs_remove_dir() recursive)
Mika Westerberg sees traces analogous to the one below in Thunderbolt
hot-remove testing:
WARNING: CPU: 0 PID: 4 at fs/sysfs/group.c:214 sysfs_remove_group+0xc6/0xd0()
sysfs group ffffffff81c6f1e0 not found for kobject 'host7'
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 3.12.0+ #13
Hardware name: /D33217CK, BIOS GKPPT10H.86A.0042.2013.0422.1439 04/22/2013
Workqueue: kacpi_hotplug acpi_hotplug_work_fn
0000000000000009 ffff8801002459b0 ffffffff817daab1 ffff8801002459f8
ffff8801002459e8 ffffffff810436b8 0000000000000000 ffffffff81c6f1e0
ffff88006d440358 ffff88006d440188 ffff88006e8b4c28 ffff880100245a48
Call Trace:
[<ffffffff817daab1>] dump_stack+0x45/0x56
[<ffffffff810436b8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81043727>] warn_slowpath_fmt+0x47/0x50
[<ffffffff811ad319>] ? sysfs_get_dirent_ns+0x49/0x70
[<ffffffff811ae526>] sysfs_remove_group+0xc6/0xd0
[<ffffffff81432f7e>] dpm_sysfs_remove+0x3e/0x50
[<ffffffff8142a0d0>] device_del+0x40/0x1b0
[<ffffffff8142a24d>] device_unregister+0xd/0x20
[<ffffffff8144131a>] scsi_remove_host+0xba/0x110
[<ffffffff8145f526>] ata_host_detach+0xc6/0x100
[<ffffffff8145f578>] ata_pci_remove_one+0x18/0x20
[<ffffffff812e8f48>] pci_device_remove+0x28/0x60
[<ffffffff8142d854>] __device_release_driver+0x64/0xd0
[<ffffffff8142d8de>] device_release_driver+0x1e/0x30
[<ffffffff8142d257>] bus_remove_device+0xf7/0x140
[<ffffffff8142a1b1>] device_del+0x121/0x1b0
[<ffffffff812e43d4>] pci_stop_bus_device+0x94/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e437b>] pci_stop_bus_device+0x3b/0xa0
[<ffffffff812e44dd>] pci_stop_and_remove_bus_device+0xd/0x20
[<ffffffff812fc743>] trim_stale_devices+0x73/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fc78b>] trim_stale_devices+0xbb/0xe0
[<ffffffff812fcb6e>] acpiphp_check_bridge+0x7e/0xd0
[<ffffffff812fd90d>] hotplug_event+0xcd/0x160
[<ffffffff812fd9c5>] hotplug_event_work+0x25/0x60
[<ffffffff81316749>] acpi_hotplug_work_fn+0x17/0x22
[<ffffffff8105cf3a>] process_one_work+0x17a/0x430
[<ffffffff8105db29>] worker_thread+0x119/0x390
[<ffffffff8105da10>] ? manage_workers.isra.25+0x2a0/0x2a0
[<ffffffff81063a5d>] kthread+0xcd/0xf0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
[<ffffffff817eb33c>] ret_from_fork+0x7c/0xb0
[<ffffffff81063990>] ? kthread_create_on_node+0x180/0x180
The source of this problem is that SCSI hosts are removed from
ATA ports after calling ata_tport_delete() which removes the
port's sysfs directory, among other things. Now, after commit
bcdde7e221, the sysfs directory is removed along with all of
its subdirectories that include the SCSI host's sysfs directory
and its subdirectories at this point. Consequently, when
device_del() is finally called for any child device of the SCSI
host and tries to remove its "power" group (which is already
gone then), it triggers the above warning.
To make the warnings go away, change the removal ordering in
ata_port_detach() so that the SCSI host is removed from the
port before ata_tport_delete() is called.
References: https://bugzilla.kernel.org/show_bug.cgi?id=65281
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The endianness attribute on the 'aux' local variable is wrong, and can
lead to wrong endianness on big-endian machines,
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the following ATA opcodes, which are present
in SATA 3.1 and T13 ATA ACS-3:
SEND FPDMA QUEUED
RECEIVE FPDMA QUEUED
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
SATA 3.1 added an "auxiliary" field to the host-to-device FIS.
Populate the host-to-device FIS with the new field via the
taskfile struct.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Overview of changes:
- The rest of maintainer email address updates.
- Some core updates - more robust default behavior for port
multipliers, better error reporting for SG_IO commands, and a way
to better work around now ancient and probably pretty rare PATA ->
SATA bridges with ATAPI devices.
- sata_rcar stabilization.
- Some hardware PCI ID additions and one-off low level driver
updates."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
AHCI: use ATA_BUSY
libata-zpodd: must use ata_tf_init()
ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
libata: cleanup SAT error translation
ahci: sata: add support for exynos5440 sata
libata: skip SRST for all SIMG [34]7x port-multipliers
ahci: remove pmp link online check in FBS EH
sata highbank: add bit-banged SGPIO driver support
ahci: make ahci_transmit_led_message into a function pointer
sata_rcar: fix compilation warning in sata_rcar_thaw()
sata_highbank: increase retry count but shorten duration for Calxeda controller
ata: use pci_get_drvdata()
ipr: qc_fill_rtf() method should not store alternate status register
sata_rcar: add 'base' local variable to some functions
sata_rcar: correct 'sata_rcar_sht'
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
libata: do not limit R-Car SATA driver to shmobile
ata: use platform_{get,set}_drvdata()
AHCI: Make distinct names for ports in /proc/interrupts
...
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.
Fix this by adding back the hotplug notification handler registration
code. Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached. So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.
With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.
[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Commit 803739d25c ("[libata] replace
sata_settings with devslp_timing"), which was also Cc: stable, used a
stack buffer to receive data from ata_read_log_page(), which triggers
the following warning:
ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948]
Fix this by using ap->sector_buf instead of a stack buffer.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For system freeze, if the port is already runtime suspended, leave it
alone and just return. The port will be resumed on thaw before it will
be used.
And since we will call get_noresume for every device during prepare
phase, and the port is resumed during thaw phase, it can't be in runtime
suspended state during the poweroff phase. So remove the
runtime_suspended check in poweroff callback.
And for all suspend(freeze/suspend/poweroff/etc.), there is no need to
touch the device, so set no_autopsy and no_recovery for them all.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to do different things for system PM and runtime PM, e.g. we do
not need to enable runtime wake for ZPODD when we are doing system
suspend, etc.
Currently, we use PMSG_SUSPEND for both system suspend and runtime
suspend and PMSG_ON for both system resume and runtime resume. Change
this by using PMSG_AUTO_SUSPEND for runtime suspend and PMSG_AUTO_RESUME
for runtime resume. And since PMSG_ON means no transition, it is changed
to PMSG_RESUME for ata port's system resume.
The ata_acpi_set_state is modified accordingly, and the sata case and
pata case is seperated for easy reading.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For ODDs, the upper layer will poll for media change every few
seconds, which will make it enter and leave suspend state very
often. And as each suspend will also cause a hard/soft reset,
the gain of runtime suspend is very little while the ODD may
malfunction after constantly being reset. So the idle callback
here will not proceed to suspend if a non-ZPODD capable ODD is
attached to the port.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ODD can be enabled for ZPODD if the following three conditions are
satisfied:
1 The ODD supports device attention;
2 The platform can runtime power off the ODD through ACPI;
3 The ODD is either slot type or drawer type.
For such ODDs, zpodd_init is called and a new structure is allocated for
it to store ZPODD related stuffs.
And the zpodd_dev_enabled function is used to test if ZPODD is currently
enabled for this ODD.
A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts commit de90cd71f6.
Shane Huang writes:
Please suspend this patch because I just received two new
DevSlp drives but found word 78 bit 5 is _not_ set.
I'm checking with the drive vendor whether he gave me
the wrong information. If bit 5 is not the necessary and
sufficient condition, I will implement another patch to
replace ata_device->sata_settings into ->devslp_timing.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This relatively simple boiler-plate code is repeated in several platform
drivers. We should implement a common version in libata.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_device->dma_mode's initial value is zero, which is not a valid dma
mode, but ata_dma_enabled will return true for this value. This patch
sets dma_mode to 0xff in reset function, so that ata_dma_enabled will
not return true for this case, or it will cause problem for pata_acpi.
The corrsponding bugzilla page is at:
https://bugzilla.kernel.org/show_bug.cgi?id=49151
Reported-by: Phillip Wood <phillip.wood@dunelm.org.uk>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Szymon Janc <szymon@janc.net.pl>
Tested-by: Dutra Julio <dutra.julio@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) should be used.
Quoting SATA spec 3.1:
If Hardware Feature Control is supported, then:
a) IDENTIFY DEVICE data word 78 bit 5 (see 13.2.1.18) shall be
set to one;
b) the SET FEATURES Select Hardware Feature Control subcommand
shall be supported (see 13.3.8);
c) page 08h of the Identify Device Data log (see 13.7.7) shall
be supported;
This patch is not tested on SATA HDD with DevSlp supported.
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_timing_find_mode could return NULL which is not checked by all
low-level ATA drivers using it and cause a NULL ptr deref. Warn at least
so that possible issues can get fixed easily.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
1) Apply -- and then revert -- the FUA feature. Caused
disk corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=i3EH
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
Since READ/WRITE FPDMA QUEUED commands are 48-bit, bit 6 of the device register
means LBA, the same as for READ/WRITE DMA EXT commands. So use ATA_LBA instead
of the bare number in ata_build_rw_tf()'s branch dedicated to the NCQ commands.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit d70e551c8e, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libsas and ipr pass flags to ata_host_init that are meant for the port.
ata_host flags:
ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */
ATA_HOST_STARTED = (1 << 1), /* Host started */
ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */
ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */
flags passed by libsas:
ATA_FLAG_SATA = (1 << 1),
ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */
ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */
The only one that aliases is ATA_HOST_STARTED which is a 'don't care' in
the libsas and ipr cases since ata_hosts from these sources are not
registered with libata.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Brian King <brking@us.ibm.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reuse ata_port_{suspend|resume}_common for sas. This path is chosen
over adding coordination between ata-tranport and sas-transport because
libsas wants to revalidate the domain at resume-time at the host level.
It can not validate links have resumed properly until libata has had a
chance to perform its revalidation, and any sane placing of an ata_port
in the sas-transport model would delay it's resumption until after the
host.
Export the common portion of port suspend/resume (bypass pm_runtime),
and allow sas to perform these operations asynchronously (similar to the
libsas async-ata probe implmentation). Async operation is determined by
having an external, rather than stack based, location for storing the
result of the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hotplug testing with libsas currently encounters a 55 second wait for
link recovery to give up. In the case where the user trusts the
response time of their devices permit the recovery attempts to be
limited to one.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, SATA disk fua detection is disabled on default because most of
devices don't support this feature at that time. With the development of
technology, more and more SATA disks support this feature. So now we can enable
this detection on default.
Although fua detection is defined as a kernel module parameter, it is too hard
to set its value because it must be loaded and set before system starts up.
That needs to modify initrd file. So it is inconvenient for administrator who
needs to manage a huge number of servers.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Michael Eitelwein writes:
I have an external SATA drive that was slowed down by bridge limits. I
found a solution in a thread on this list posted in 2008: It introduces
whitelist entries in libata-core.c for devices with well working bridges
(e.g. email on Fri, 31 Oct 2008 01:45:27 -0400).
I added my device to this whitelist in a custom built kernel and it
works fine for weeks now. How can I have this device added on the
whitelist within the official kernel? Is this whitelist mechanism still
supported or is there a smarter way to achieve whitelisting?
I added the following whitelist entry for my Buffalo DriveStation
Quattro "BUFFALO HD-QSU2/R5":
/* Devices that do not need bridging limits applied */
{ "MTRON MSP-SATA*", NULL, ATA_HORKAGE_BRIDGE_OK, },
{ "BUFFALO HD-QSU2/R5", NULL, ATA_HORKAGE_BRIDGE_OK, },
Reported-by: Michael Eitelwein <michael@eitelwein.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When managing shost->host_eh_scheduled libata assumes that there is a
1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship
so it needs to manage host_eh_scheduled cumulatively at the host level.
The sched_eh and end_eh port port ops allow libsas to track when domain
devices enter/leave the "eh-pending" state under ha->lock (previously
named ha->state_lock, but it is no longer just a lock for ha->state
changes).
Since host_eh_scheduled indicates eh without backing commands pinning
the device it can be deallocated at any time. Move the taking of the
domain_device reference under the port_lock to guarantee that the
ata_port stays around for the duration of eh.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a new flag ATA_DFLAG_DA to indicate that device supports "Device
Attention".
Acked-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that we have the ability to directly glue the ACPI namespace to the
driver model in libata, we don't need the custom code to handle the same
thing. Remove it and migrate the functions over to the new code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Associate the ACPI device tree and libata devices.
This patch uses the generic ACPI glue framework to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A user has several systems with a couple of models of flash disks with IDE
connectors. These disks work fine in 2.6.18-ish kernels but corrupt data on
new kernels.
The difference appears to be with the default I/O method used by the IDE
controller driver between the kernels. In the older kernels, the
configuration is very conservative and the driver stays in PIO mode. With
new kernels, the ata driver (pata_serverworks) attempts to use UDMA/66
which the drive claims to support. This mode, however, does not appear to
work in DMA mode. The drive does work correctly and no corruption is
seen if the kernel parameter "libata.force=5:pio0,6:pio0" is used to force
the driver to use PIO instead of DMA mode.
Blacklist these drives. Unfortunately the model name of the drive is very
generic, " 2GB ATA Flash Disk", but the revision is specific, "ADMA428M".
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Where devices are visible via more than one host we sometimes wish to
indicate that cirtain devices should be ignored on a specific host. Add a
host flag indicating that this host wishes to ignore ATA specific devices.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:
-ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
-ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
-ata3: DUMMY
+ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
+ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
ata4: DUMMY
ata5: DUMMY
-ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
+ata6: DUMMY
+ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
The change of numbering comes from commit 85d6725b7c ("libata:
make ata_print_id atomic") that changed lines like
ap->print_id = ata_print_id++;
to
ap->print_id = atomic_inc_return(&ata_print_id);
As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This variable is incremented from multiple contexts (module_init via
libata-lldds and the libsas discovery thread). Make it atomic to head
off any chance of libsas and libata creating duplicate ids.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit b3a706014e (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated. Do this
now, and make a line added back then wrapped properly...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.
Add ata port type driver which implements port PM callbacks.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
XFER_SW_DMA_0 mode should be excluded from the extended cycle timing
computations.
Acked-by: Alan Cox <alan@linux.intel.com>
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link resume failure in itself isn't an error condition and may happen
regularly depending on hardware configuration. Reporting it as
KERN_ERR makes the condition unnecessarily prominent (e.g. reported
during boot). Use KERN_WARNING instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Shaw <dshaw@jabberwocky.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use a single mechanism to show driver version.
Reduces text a tiny bit too.
Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.
$ size drivers/ata/built-in.*
text data bss dec hex filename
544969 73893 116584 735446 b38d6 drivers/ata/built-in.allyesconfig.ata.o
543870 73893 116592 734355 b34ad drivers/ata/built-in.allyesconfig.print_once.o
141328 14689 4220 160237 271ed drivers/ata/built-in.defconfig.ata.o
141212 14689 4220 160121 27179 drivers/ata/built-in.defconfig.print_once.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Saves a bit of text as the call takes fewer args.
Coalesce a few formats.
Convert a few bare printks to pr_cont.
$ size drivers/ata/built-in.o*
text data bss dec hex filename
558429 73893 117864 750186 b726a drivers/ata/built-in.o.allyesconfig.new
559574 73893 117888 751355 b76fb drivers/ata/built-in.o.allyesconfig.old
149567 14689 4220 168476 2921c drivers/ata/built-in.o.defconfig.new
149851 14689 4220 168760 29338 drivers/ata/built-in.o.defconfig.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
regardless of firmware revision
It's unlikely NOSETXFER works for a revision of drive but doesn't for
another and pioneer doesn't seem to be fixing firmwares for the
affected drives. Apply NOSETXFER to the affected pioneer drives
regardless of firmware revision.
http://article.gmane.org/gmane.linux.ide/49734
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fl-00@gmx.de
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Give users the option of completely powering off unoccupied
SATA ports using the existing min_power link_power_management_policy
option. When the use selects this option on an empty port, we
will power the port off by setting DET to off. For occupied ports,
behavior is unchanged.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 4a5610a04d fixed an issue with
the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
reported a similar issue with his DVR-216D that the NOSETXFER horkage
worked around for him as well.
This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.
The issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=679143
Reported-by: Volodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Tejun Heo