Commit Graph

680 Commits

Author SHA1 Message Date
Marcel Holtmann e4e8e37c42 [Bluetooth] Make use of the default link policy settings
The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14 20:13:47 +02:00
Marcel Holtmann a8746417e8 [Bluetooth] Track connection packet type changes
The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.

On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.

When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14 20:13:46 +02:00
Marcel Holtmann 9dc0a3afc0 [Bluetooth] Support the case when headset falls back to SCO link
When trying to establish an eSCO link between two devices then it can
happen that the remote device falls back to a SCO link. Currently this
case is not handled correctly and the message dispatching will break
since it is looking for eSCO packets. So in case the configured link
falls back to SCO overwrite the link type with the correct value.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14 20:13:46 +02:00
Marcel Holtmann ae29319649 [Bluetooth] Update authentication status after successful encryption
The authentication status is not communicated to both parties. This is
actually a flaw in the Bluetooth specification. Only the requesting side
really knows if the authentication was successful or not. This piece of
information is however needed on the other side to know if it has to
trigger the authentication procedure or not. Worst case is that both
sides will request authentication at different times, but this should
be avoided since it costs extra time when setting up a new connection.

For Bluetooth encryption it is required to authenticate the link first
and the encryption status is communicated to both sides. So when a link
is switched to encryption it is possible to update the authentication
status since it implies an authenticated link.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14 20:13:45 +02:00
Harvey Harrison 8398531939 bluetooth: use get/put_unaligned_* helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-05-02 16:25:46 -07:00
Marcel Holtmann b6a0dc8224 [Bluetooth] Add support for handling simple eSCO links
With the Bluetooth 1.2 specification the Extended SCO feature for
better audio connections was introduced. So far the Bluetooth core
wasn't able to handle any eSCO connections correctly. This patch
adds simple eSCO support while keeping backward compatibility with
older devices.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-22 02:59:47 -07:00
Marcel Holtmann a9de924806 [Bluetooth] Switch from OGF+OCF to using only opcodes
The Bluetooth HCI commands are divided into logical OGF groups for
easier identification of their purposes. While this still makes sense
for the written specification, its makes the code only more complex
and harder to read. So instead of using separate OGF and OCF values
to identify the commands, use a common 16-bit opcode that combines
both values. As a side effect this also reduces the complexity of
OGF and OCF calculations during command header parsing.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-22 02:59:40 -07:00
Marcel Holtmann 5b7f990927 [Bluetooth] Add basics to better support and handle eSCO links
To better support and handle eSCO links in the future a bunch of
constants needs to be added and some basic routines need to be
updated. This is the initial step.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-07-11 07:35:32 +02:00
YOSHIFUJI Hideaki aca3192cc6 [NET] BLUETOOTH: Use cpu_to_le{16,32}() where appropriate.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:23:54 -07:00
Tim Schmielau cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00
YOSHIFUJI Hideaki 8e87d14255 [NET] BLUETOOTH: Fix whitespace errors.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-02-10 23:19:20 -08:00
Marcel Holtmann 6bd5741612 [Bluetooth] Handling pending connect attempts after inquiry
After an inquiry completed or got canceled the Bluetooth core should
check for any pending connect attempts.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-11-21 16:16:29 -08:00
Marcel Holtmann 4c67bc74f0 [Bluetooth] Support concurrent connect requests
Most Bluetooth chips don't support concurrent connect requests, because
this would involve a multiple baseband page with only one radio. In the
case an upper layer like L2CAP requests a concurrent connect these chips
return the error "Command Disallowed" for the second request. If this
happens it the responsibility of the Bluetooth core to queue the request
and try again after the previous connect attempt has been completed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-10-15 23:14:30 -07:00
Marcel Holtmann 37e97b4ef0 [Bluetooth]: Don't update disconnect timer for incoming connections
In the case of device pairing the only safe method is to establish
a low-level ACL link. In this case, the remote side should not use
the disconnect timer to give the other side the chance to enter the
PIN code. If the disconnect timer is used, the connection will be
dropped to soon, because it is impossible to identify an actual user
of this link.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-28 18:03:11 -07:00
Marcel Holtmann 6ac59344ef [Bluetooth] Support create connection cancel command
In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-09-28 18:01:33 -07:00
Marcel Holtmann 1143e5a6d4 [Bluetooth] Read local version information on device init
The local version information are needed to identify certain feature
sets of devices. They must be read on device init and stored for later
use. It is also possible to access them through the device model.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-09-28 18:01:32 -07:00
Marcel Holtmann defc761bc2 [Bluetooth] Handle command complete event for exit periodic inquiry
The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-09-28 18:01:29 -07:00
Marcel Holtmann 04837f6447 [Bluetooth] Add automatic sniff mode support
This patch introduces the automatic sniff mode feature. This allows
the host to switch idle connections into sniff mode to safe power.

Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-07-03 19:53:58 -07:00
Marcel Holtmann da1f519851 [Bluetooth] Correct SCO buffer size on request
This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.

Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2006-07-03 19:53:56 -07:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Marcel Holtmann 1ebb92521d [Bluetooth]: Add endian annotations to the core
This patch adds the endian annotations to the Bluetooth core.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-11-08 09:57:21 -08:00
Marcel Holtmann 21d9e30ed0 [Bluetooth] Add support for extended inquiry responses
This patch adds the handling of the extended inquiry responses and
inserts them into the inquiry cache.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-09-13 01:32:25 +02:00
Patrick McHardy a61bbcf28a [NET]: Store skb->timestamp as offset to a base timestamp
Reduces skb size by 8 bytes on 64-bit.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:58:24 -07:00
Marcel Holtmann 0d48d93947 [Bluetooth]: Move packet type into the SKB control buffer
This patch moves the usage of packet type into the SKB control
buffer. After this patch it is now possible to shrink the sk_buff
structure and redefine its pkt_type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:55:13 -07:00
Marcel Holtmann 85a1e930bf [Bluetooth]: Track page scan repetition mode changes
The HCI page scan repetition mode change event contains the actual
page scan repetition mode for the remote device. It is the same
value that is received from an inquiry response and it can be used
to make further reconnections faster.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:54:53 -07:00
Marcel Holtmann 45bb4bf08b [Bluetooth]: Workaround for inquiry results with RSSI and page scan mode
This patch implements a workaround for buggy Bluetooth 1.2 devices from
Silicon Wave. Their inquiry results with RSSI contain the page scan mode
field. This field was removed in the final Bluetooth 1.2 specification.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:54:47 -07:00
Marcel Holtmann 576c7d858f [Bluetooth] Add direction and timestamp to stack internal events
This patch changes the direction to incoming and adds the timestamp
to all stack internal events.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-08-06 12:36:54 +02:00
Marcel Holtmann 66e8b6c31b [Bluetooth] Remove unused functions and cleanup symbol exports
This patch removes the unused bt_dump() function and it also removes
its BT_DMP macro. It also unexports the hci_dev_get(), hci_send_cmd()
and hci_si_event() functions.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-08-06 12:36:51 +02:00
Al Viro b453257f05 [PATCH] kill gratitious includes of major.h under net/*
A lot of places in there are including major.h for no reason whatsoever.
Removed.  And yes, it still builds. 

The history of that stuff is often amusing.  E.g.  for net/core/sock.c
the story looks so, as far as I've been able to reconstruct it: we used
to need major.h in net/socket.c circa 1.1.early.  In 1.1.13 that need
had disappeared, along with register_chrdev(SOCKET_MAJOR, "socket",
&net_fops) in sock_init().  Include had not.  When 1.2 -> 1.3 reorg of
net/* had moved a lot of stuff from net/socket.c to net/core/sock.c,
this crap had followed... 

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-25 18:32:13 -07:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00