Documentation/driver-api/target.rst is seeking kerneldoc comments in
drivers/target/target_core_device.c, but no such comments exist. Take out
the kernel-doc directive and eliminate one warning from the build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The stratix10 service layer documentation tried to include a kerneldoc
comments for a nonexistent struct; leading to a "no structured comments
found" message. Switch it to stratix10_svc_command_config_type, which
appears at that spot in the sequence and was not included.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to
be handled consistently. Unsurprisingly, we enforce the lines to
be either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone
does, so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed.
Such nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs
and outputs at the same time and after improving the MMIO library
we handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM
work as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update.
-----BEGIN PGP SIGNATURE-----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=rhto
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
later than usual because I was ironing out my own mistakes. I'm
holding some stuff back for the next kernel as a result, and this
should be a healthy and well tested batch.
Core changes:
- The gpiolib MMIO driver has been enhanced to handle two direction
registers, i.e. one register to set lines as input and one register
to set lines as output. It turns out some silicon engineer thinks
the ability to configure a line as input and output at the same
time makes sense, this can be debated but includes a lot of analog
electronics reasoning, and the registers are there and need to be
handled consistently. Unsurprisingly, we enforce the lines to be
either inputs or outputs in such schemes.
- Send in the proper argument value to .set_config() dispatched to
the pin control subsystem. Nobody used it before, now someone does,
so fix it to work as expected.
- The ACPI gpiolib portions can now handle pin bias setting (pull up
or pull down). This has been in the ACPI spec for years and we
finally have it properly integrated with Linux GPIOs. It was based
on an observation from Andy Schevchenko that Thomas Petazzoni's
changes to the core for biasing the PCA950x GPIO expander actually
happen to fit hand-in-glove with what the ACPI core needed. Such
nice synergies happen sometimes.
New drivers:
- A new driver for the Mellanox BlueField GPIO controller. This is
using 64bit MMIO registers and can configure lines as inputs and
outputs at the same time and after improving the MMIO library we
handle it just fine. Interesting.
- A new IXP4xx proper gpiochip driver with hierarchical interrupts
should be coming in from the ARM SoC tree as well.
Driver enhancements:
- The PCA053x driver handles the CAT9554 GPIO expander.
- The PCA053x driver handles the NXP PCAL6416 GPIO expander.
- Wake-up support on PCA053x GPIO lines.
- OMAP now does a nice asynchronous IRQ handling on wake-ups by
letting everything wake up on edges, and this makes runtime PM work
as expected too.
Misc:
- Several cleanups such as devres fixes.
- Get rid of some languager comstructs that cause problems when
compiling with LLVMs clang.
- Documentation review and update"
* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: Update documentation
docs: gpio: convert docs to ReST and rename to *.rst
gpio: sch: Remove write-only core_base
gpio: pxa: Make two symbols static
gpiolib: acpi: Respect pin bias setting
gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
gpiolib: acpi: Set pin value, based on bias, more accurately
gpiolib: acpi: Change type of dflags
gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
gpiolib: Make use of enum gpio_lookup_flags consistent
gpiolib: Indent entry values of enum gpio_lookup_flags
gpio: pca953x: add support for pca6416
dt-bindings: gpio: pca953x: document the nxp,pca6416
gpio: pca953x: add pcal6416 to the of_device_id table
gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
tracing: stop making gpio tracing configurable
gpio: pca953x: Configure wake-up path when wake-up is enabled
gpio: of: Optimize quirk checks
gpio: mmio: Drop bgpio_dir_inverted
...
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
- Lots of work on the Chinese and Italian translations
- Some license-rules clarifications from Christoph
- Various build-script fixes
- A new document on memory models
- RST conversion of the live-patching docs
- The usual collection of typo fixes and corrections.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzSBFkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YUDgIAIn+I0Wjv/vkuh5SKwAmz2wZBf46FCICz7Vg
jePmhd1GQ3K9k/xzIKMoaJOipAl+IXT4AnGa9eu+9Xm+D6HejASvtt/uTce4+qPi
9VLu7GmbtQQ0imRi4jjitenrebQXSKudAYbH+/bz7ycH7twWVJWKNLNQ8im9U5Ul
LRXQhRsYc2SwJ4mGOGTrqZkb69qkiOy0dQFGKbSM3ipHs/CQy8XMhlY/7aAh7t9N
SmKyH341s4Z/dRZIpoSx2QOfSp7njwTw7hxrnOq5unB82u2zrYvVFGxp5kzfQIyC
B/q26TG5hVNGH/37/+yOoziyP3Ma8IuF5W0zcg9DbmIi0Gdvg7s=
=4Zhc
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A reasonably busy cycle for docs, including:
- Lots of work on the Chinese and Italian translations
- Some license-rules clarifications from Christoph
- Various build-script fixes
- A new document on memory models
- RST conversion of the live-patching docs
- The usual collection of typo fixes and corrections"
* tag 'docs-5.2' of git://git.lwn.net/linux: (140 commits)
docs/livepatch: Unify style of livepatch documentation in the ReST format
docs: livepatch: convert docs to ReST and rename to *.rst
scripts/documentation-file-ref-check: detect broken :doc:`foo`
scripts/documentation-file-ref-check: don't parse Next/ dir
LICENSES: Rename other to deprecated
LICENSES: Clearly mark dual license only licenses
docs: Don't reference the ZLib license in license-rules.rst
docs/vm: Minor editorial changes in the THP and hugetlbfs
docs/vm: add documentation of memory models
doc:it_IT: translation alignment
doc: fix typo in PGP guide
dontdiff: update with Kconfig build artifacts
docs/zh_CN: fix typos in 1.Intro.rst file
docs/zh_CN: redirect CoC docs to Chinese version
doc: mm: migration doesn't use FOLL_SPLIT anymore
docs: doc-guide: remove the extension from .rst files
doc: kselftest: Fix KBUILD_OUTPUT usage instructions
docs: trace: fix some Sphinx warnings
docs: speculation.txt: mark example blocks as such
docs: ntb.txt: add blank lines to clean up some Sphinx warnings
...
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
Strictify the language a bit, move things around, make proper
headings, mention pull-up and pull-down, expand unreadable
acronyms etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix the handling of Performance and Energy Bias Hint (EPB) on
Intel processors and expose it to user space via sysfs to avoid
having to access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor
and rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to
some PM documentation files and unify copyright notices in
them (Rafael Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to
the rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan).
-----BEGIN PGP SIGNATURE-----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=nY9p
-----END PGP SIGNATURE-----
Merge tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These fix the (Intel-specific) Performance and Energy Bias Hint (EPB)
handling and expose it to user space via sysfs, fix and clean up
several cpufreq drivers, add support for two new chips to the qoriq
cpufreq driver, fix, simplify and clean up the cpufreq core and the
schedutil governor, add support for "CPU" domains to the generic power
domains (genpd) framework and provide low-level PSCI firmware support
for that feature, fix the exynos cpuidle driver and fix a couple of
issues in the devfreq subsystem and clean it up.
Specifics:
- Fix the handling of Performance and Energy Bias Hint (EPB) on Intel
processors and expose it to user space via sysfs to avoid having to
access it through the generic MSR I/F (Rafael Wysocki).
- Improve the handling of global turbo changes made by the platform
firmware in the intel_pstate driver (Rafael Wysocki).
- Convert some slow-path static_cpu_has() callers to boot_cpu_has()
in cpufreq (Borislav Petkov).
- Fix the frequency calculation loop in the armada-37xx cpufreq
driver (Gregory CLEMENT).
- Fix possible object reference leaks in multuple cpufreq drivers
(Wen Yang).
- Fix kerneldoc comment in the centrino cpufreq driver (dongjian).
- Clean up the ACPI and maple cpufreq drivers (Viresh Kumar, Mohan
Kumar).
- Add support for lx2160a and ls1028a to the qoriq cpufreq driver
(Vabhav Sharma, Yuantian Tang).
- Fix kobject memory leak in the cpufreq core (Viresh Kumar).
- Simplify the IOwait boosting in the schedutil cpufreq governor and
rework the TSC cpufreq notifier on x86 (Rafael Wysocki).
- Clean up the cpufreq core and statistics code (Yue Hu, Kyle Lin).
- Improve the cpufreq documentation, add SPDX license tags to some PM
documentation files and unify copyright notices in them (Rafael
Wysocki).
- Add support for "CPU" domains to the generic power domains (genpd)
framework and provide low-level PSCI firmware support for that
feature (Ulf Hansson).
- Rearrange the PSCI firmware support code and add support for
SYSTEM_RESET2 to it (Ulf Hansson, Sudeep Holla).
- Improve genpd support for devices in multiple power domains (Ulf
Hansson).
- Unify target residency for the AFTR and coupled AFTR states in the
exynos cpuidle driver (Marek Szyprowski).
- Introduce new helper routine in the operating performance points
(OPP) framework (Andrew-sh.Cheng).
- Add support for passing on-die termination (ODT) and auto power
down parameters from the kernel to Trusted Firmware-A (TF-A) to the
rk3399_dmc devfreq driver (Enric Balletbo i Serra).
- Add tracing to devfreq (Lukasz Luba).
- Make the exynos-bus devfreq driver suspend all devices on system
shutdown (Marek Szyprowski).
- Fix a few minor issues in the devfreq subsystem and clean it up
somewhat (Enric Balletbo i Serra, MyungJoo Ham, Rob Herring,
Saravana Kannan, Yangtao Li).
- Improve system wakeup diagnostics (Stephen Boyd).
- Rework filesystem sync messages emitted during system suspend and
hibernation (Harry Pan)"
* tag 'pm-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
cpufreq: Fix kobject memleak
cpufreq: armada-37xx: fix frequency calculation for opp
cpufreq: centrino: Fix centrino_setpolicy() kerneldoc comment
cpufreq: qoriq: add support for lx2160a
x86: tsc: Rework time_cpufreq_notifier()
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
cpufreq: qoriq: Add ls1028a chip support
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
cpufreq: Move ->get callback check outside of __cpufreq_get()
PM / Domains: remove unnecessary unlikely()
cpufreq: Remove needless bios_limit check in show_bios_limit()
drivers/cpufreq/acpi-cpufreq.c: This fixes the following checkpatch warning
firmware/psci: add support for SYSTEM_RESET2
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
...
- Convert the ACPI documentation in the kernel source tree to the
.rst format and split it into the admin guide, driver API and
firmware guide parts (Changbin Du).
- Add a PRP0001 usage example to the ACPI documentation (Thomas
Preston).
- Switch over the users of the acpi_dev_get_first_match_name()
library function which turned out to be problematic to a new,
better one called acpi_dev_get_first_match_dev() (Andy Shevchenko,
YueHaibing).
- Update the ACPICA code in the kernel to upstream release 20190405
including:
* Null pointer dereference check in acpi_ns_delete_node() (Erik
Schmauss).
* Multiple macro and function name changes (Bob Moore).
* Predefined operation region name fix (Erik Schmauss).
- Fix hibernation issue on systems using the Baytrail and
Cherrytrail Intel SoCs introduced during the 4.20 development
cycle (Hans de Goede).
- Add Sony VPCEH3U1E to the backlight quirk list (Zhang Rui).
- Fix button handling during system resume (Zhang Rui).
- Add a device PM diagnostic message (Rafael Wysocki).
- Clean up the code, comments and white space in multiple places
(Bjorn Helgaas, Gustavo Silva, Kefeng Wang).
-----BEGIN PGP SIGNATURE-----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=LtlV
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These rearrange the ACPI documentation by converting it to the .rst
format and splitting it into clear categories (admin guide, driver
API, firmware guide), switch over multiple users of a problematic
library function to a new better one, update the ACPICA code in the
kernel to a new upstream release, fix a few issues, improve power
device management diagnostics and do some cleanups.
Specifics:
- Convert the ACPI documentation in the kernel source tree to the
.rst format and split it into the admin guide, driver API and
firmware guide parts (Changbin Du).
- Add a PRP0001 usage example to the ACPI documentation (Thomas
Preston).
- Switch over the users of the acpi_dev_get_first_match_name()
library function which turned out to be problematic to a new,
better one called acpi_dev_get_first_match_dev() (Andy Shevchenko,
YueHaibing).
- Update the ACPICA code in the kernel to upstream release 20190405
including:
* Null pointer dereference check in acpi_ns_delete_node() (Erik
Schmauss).
* Multiple macro and function name changes (Bob Moore).
* Predefined operation region name fix (Erik Schmauss).
- Fix hibernation issue on systems using the Baytrail and Cherrytrail
Intel SoCs introduced during the 4.20 development cycle (Hans de
Goede).
- Add Sony VPCEH3U1E to the backlight quirk list (Zhang Rui).
- Fix button handling during system resume (Zhang Rui).
- Add a device PM diagnostic message (Rafael Wysocki).
- Clean up the code, comments and white space in multiple places
(Bjorn Helgaas, Gustavo Silva, Kefeng Wang)"
* tag 'acpi-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
Documentation: ACPI: move video_extension.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move ssdt-overlays.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move lpit.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move cppc_sysfs.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move apei/einj.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move apei/output_format.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move aml-debugger.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move method-tracing.txt to firmware-guide/acpi and convert to rsST
Documentation: ACPI: move debug.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/data-node-references.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsd/graph.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move acpi-lid.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move i2c-muxes.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move dsdt-override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move initrd_table_override.txt to admin-guide/acpi and convert to reST
Documentation: ACPI: move method-customizing.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move gpio-properties.txt to firmware-guide/acpi and convert to reST
Documentation: ACPI: move DSD-properties-rules.txt to firmware-guide/acpi and covert to reST
Documentation: ACPI: move scan_handlers.txt to driver-api/acpi and convert to reST
Documentation: ACPI: move linuxized-acpica.txt to driver-api/acpi and convert to reST
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
This converts the plain text documentation to reStructuredText format
and adds it to Sphinx TOC tree.
No essential content change.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This converts the plain text documentation to reStructuredText format
and adds it to Sphinx TOC tree.
No essential content change.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add below index.rst files for ACPI subsystem. More docs will be added later.
o admin-guide/acpi/index.rst
o driver-api/acpi/index.rst
o firmware-guide/index.rst
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds high-level documentation about the Generic Counter
interface.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The guarantees provided by mmiowb() are now provided implicitly by
spin_unlock(), so remove all references to this most confusing of
barriers from our Documentation.
Good riddance.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Unify copyright notices in the .rst files under
Documentation/driver-api/pm and Documentation/admin-quide/pm.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add SPDX license tags to .rst files under Documentation/driver-api/pm
and Documentation/admin-quide/pm.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The way the document is written now, Sphinx renders empty code blocks
followed by the lines that should be inside them.
Unindent the code-block directives to fix this.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
UAPI Changes:
- Add Colorspace connector property (Uma)
- fourcc: Several new YUV formats from ARM (Brian & Ayan)
- fourcc: Fix merge conflicts between new formats above and Swati's that
went in via topic/hdr-formats-2019-03-07 branch (Maarten)
Cross-subsystem Changes:
- Typed component support via topic/component-typed-2019-02-11 (Maxime/Daniel)
Core Changes:
- Improve component helper documentation (Daniel)
- Avoid calling drm_dev_unregister() twice on unplugged devices (Noralf)
- Add device managed (devm) drm_device init function (Noralf)
- Graduate TINYDRM_MODE to DRM_SIMPLE_MODE in core (Noralf)
- Move MIPI/DSI rate control params computation into core from i915 (David)
- Add support for shmem backed gem objects (Noralf)
Driver Changes:
- various: Use of_node_name_eq for node name comparisons (Rob Herring)
- sun4i: Add DSI burst mode support (Konstantin)
- panel: Add Ronbo RB070D30 MIPI/DSI panel support (Konstantin)
- virtio: A few prime improvements (Gerd)
- tinydrm: Remove tinydrm_device (Noralf)
- vc4: Add load tracker to driver to detect underflow in atomic check (Boris)
- vboxvideo: Move it out of staging \o/ (Hans)
- v3d: Add support for V3D v4.2 (Eric)
Cc: Konstantin Sudakov <k.sudakov@integrasources.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Ayan Kumar Halder <ayan.halder@arm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlyTxEYACgkQlvcN/ahK
Bwpfhgf9HTwlxHKPwRL70o5Ilp7JVjeLjM5IgDgz+o7F+UZn2OdWocmSDAbJ+lwe
V+LXImc5tykGNRzgn4lXljGv3jqxOgVOxEBo53hVjXeYE/jIdbGDF1cx+1tSke67
lbO61dD9RM5GG9eLuzZ9S72qv5mfBYKHJZuULqOei/Ohnubkg0kDQ3zQEFDah1mh
kqHJkd+x1PwcwBnAjbWdIaCMiwrVmxj7yXLQS8bJzSFKc0/r7HlG8qNWmiBllH0D
aRMO2phHkXCVZY+GWWCEOZwz7ve23sibYm9tzBS69nbWJL12CAomB/8LrRPM2K5v
tVBNrX0eNHMKtOa0En0oF37BXUXizQ==
=DVKQ
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-03-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.2:
UAPI Changes:
- Add Colorspace connector property (Uma)
- fourcc: Several new YUV formats from ARM (Brian & Ayan)
- fourcc: Fix merge conflicts between new formats above and Swati's that
went in via topic/hdr-formats-2019-03-07 branch (Maarten)
Cross-subsystem Changes:
- Typed component support via topic/component-typed-2019-02-11 (Maxime/Daniel)
Core Changes:
- Improve component helper documentation (Daniel)
- Avoid calling drm_dev_unregister() twice on unplugged devices (Noralf)
- Add device managed (devm) drm_device init function (Noralf)
- Graduate TINYDRM_MODE to DRM_SIMPLE_MODE in core (Noralf)
- Move MIPI/DSI rate control params computation into core from i915 (David)
- Add support for shmem backed gem objects (Noralf)
Driver Changes:
- various: Use of_node_name_eq for node name comparisons (Rob Herring)
- sun4i: Add DSI burst mode support (Konstantin)
- panel: Add Ronbo RB070D30 MIPI/DSI panel support (Konstantin)
- virtio: A few prime improvements (Gerd)
- tinydrm: Remove tinydrm_device (Noralf)
- vc4: Add load tracker to driver to detect underflow in atomic check (Boris)
- vboxvideo: Move it out of staging \o/ (Hans)
- v3d: Add support for V3D v4.2 (Eric)
Cc: Konstantin Sudakov <k.sudakov@integrasources.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Ayan Kumar Halder <ayan.halder@arm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321170805.GA50145@art_vandelay
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
and more translations. There's also some LICENSES adjustments from
Thomas.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlyBl54PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YxoYH/3OcInUSk17Cb+wNpnJX66dXyVvzZcuAh5aU
HW5YWIIlp60jwsM0z+sVqNR51tfC+eMjw2HOWj0hOEUju7UGm7aDtB+WkEeJ7GUk
e/FX+GXD/OygQtpwXRQraWU/RO3RPSB9JKodF5tQ6aihOzsQGB9c11I0/f3Qp7+U
vaLBOdAlpQYemlzLKbskRZ2YpokELfpgwSb6O7mpI9i3mJeZA/lpyYSmHQxqwvG7
sqrmm7vHB7b0tZGqQISQaZNdUmSSD1lRfOX3brFw2DOIj2V2M1+O/8smBtRuAGf5
B03C7LjkNFn55tn1OHYlWEv8RpG5kH3VNc896jiWPDOXNpMSgl8=
=bOsl
-----END PGP SIGNATURE-----
Merge tag 'docs-5.1' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A fairly routine cycle for docs - lots of typo fixes, some new
documents, and more translations. There's also some LICENSES
adjustments from Thomas"
* tag 'docs-5.1' of git://git.lwn.net/linux: (74 commits)
docs: Bring some order to filesystem documentation
Documentation/locking/lockdep: Drop last two chars of sample states
doc: rcu: Suspicious RCU usage is a warning
docs: driver-api: iio: fix errors in documentation
Documentation/process/howto: Update for 4.x -> 5.x versioning
docs: Explicitly state that the 'Fixes:' tag shouldn't split lines
doc: security: Add kern-doc for lsm_hooks.h
doc: sctp: Merge and clean up rst files
Docs: Correct /proc/stat path
scripts/spdxcheck.py: fix C++ comment style detection
doc: fix typos in license-rules.rst
Documentation: fix admin-guide/README.rst minimum gcc version requirement
doc: process: complete removal of info about -git patches
doc: translations: sync translations 'remove info about -git patches'
perf-security: wrap paragraphs on 72 columns
perf-security: elaborate on perf_events/Perf privileged users
perf-security: document collected perf_events/Perf data categories
perf-security: document perf_events/Perf resource control
sysfs.txt: add note on available attribute macros
docs: kernel-doc: typo "if ... if" -> "if ... is"
...
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+euQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyTgCfbV8CLums843sBnT8NnWrTMTdTCcAn1K4re0m
ep8g+6oRLxJy414hogxQ
=bLs2
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (65 commits)
driver core: platform: remove misleading err_alloc label
platform: set of_node in platform_device_register_full()
firmware: hardcode the debug message for -ENOENT
driver core: Add missing description of new struct device_link field
driver core: Fix PM-runtime for links added during consumer probe
drivers/component: kerneldoc polish
async: Add cmdline option to specify drivers to be async probed
driver core: Fix possible supplier PM-usage counter imbalance
PM-runtime: Fix __pm_runtime_set_status() race with runtime resume
driver: platform: Support parsing GpioInt 0 in platform_get_irq()
selftests: firmware: fix verify_reqs() return value
Revert "selftests: firmware: remove use of non-standard diff -Z option"
Revert "selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to config"
device: Fix comment for driver_data in struct device
kernfs: Allocating memory for kernfs_iattrs with kmem_cache.
sysfs: remove unused include of kernfs-internal.h
driver core: Postpone DMA tear-down until after devres release
driver core: Document limitation related to DL_FLAG_RPM_ACTIVE
PM-runtime: Take suppliers into account in __pm_runtime_set_status()
device.h: Add __cold to dev_<level> logging functions
...
Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they asked
me to do as the MEI driver is starting to interact with the i915 driver,
and it needed some coordination. All of those patches have been
properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+dPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym1fACgvpZAxjNzoRQJ6f06tc8ujtPk9rUAnR+tCtrZ
9e3l7H76oe33o96Qjhor
=8A2k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
- Update the PM-runtime framework to use ktime instead of
jiffies for accounting (Thara Gopinath, Vincent Guittot).
- Optimize the autosuspend code in the PM-runtime framework
somewhat (Ladislav Michl).
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla).
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki).
- Add Jacobsville support to the intel_idle driver (Zhang Rui).
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam).
- Add new cpufreq driver for Armada 8K (Gregory Clement).
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar,
Amit Kucheria).
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar).
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria).
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar).
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang).
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki).
- Clean up multiple cpufreq drivers (Yangtao Li).
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn).
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann,
Matthias Kaehlcke).
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui).
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar).
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJcfSGlAAoJEILEb/54YlRxikwP/1rQ9+HqDmDUvO2QeYREGO/m
R4kK+iUQW7O4ZJzsSvoGyuKCl7c2ANPlJWmbsEZKbevpKZ4XuUcv/CJDqKD1izV7
hfsQyum34ePSCUEMf6CpMAGAkdmK//NVysHiLXZ4j1hhzi6gA6Cm50qyNZ8xX6kF
Ri6zYG5x7nhn/o/l569FDe+K5W/LDDaZUmvr858pPsrZZR5c4p3ylq+HBrZt0FPQ
70D+u7RcT5v3DQLTghNrgHHiOJ0/DQM43I7aZvkKM3JA8BCDou/Nvq+gH0C0YUP0
QE+oFK9C8CBPEz9N9cSMTb0+S78GQNB0GntJPDN3QQFCHRe6EYKUtu6CvllIE1v9
5pFfagXGVi9UmShu80v+qGGUILVK1ZJ5fjSyxx4UcneTsarNJZg7Y7d72mrX+0zi
J3KodcqQi295jNq9P55K/9XtAiRdpRR6bQzXBtrprpw8PA94yqBHPpxbD32Wl05/
U2+ss/SNyMAzhsP9kqzxSxPBlTFek/ArxZm0Uk4kHt75gkl09CG64r+6OG8gLtwD
Skkr02AeYvx6fx0kFnKIS4sc2c2/8xW3FUtHlv+TDPvuzCEaL0ooqsWgt7rcwlmg
Xz5ufXbEIiVSlLlH/YGZxbgy+WfIzYA5WMpYrA1Givn8s5jI9Sm+ROD2qhOKA2n4
aekEDkum/bxVVeykZaXy
=TSKG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
Improve IIO documentation by fixing a few mistakes.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
According to the manpage of poll(2) and also looking at the respective
syscall providing POLLERR in .events is a no-op. So don't recommend
using it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that component has docs it's worth spending a few words and
hyperlinks on recommended best practices in drm.
v2: Add another item that component shouldn't be preferred over
drm_bridge/panel and similar subsystems already providing specialized
support for specific components (Laurent). Also convert to bullet
list.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190212164615.13370-1-daniel.vetter@ffwll.ch
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
-----BEGIN PGP SIGNATURE-----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=nV64
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
Typo: the data line is called "SDA" not "SCA".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This is needed by the new MEI-HDCP support in i915, so will need to go
in through drm and drivers-misc trees at least.
-----BEGIN PGP SIGNATURE-----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=IhHa
-----END PGP SIGNATURE-----
Merge tag 'topic/component-typed-2019-02-11' of git://anongit.freedesktop.org/drm/drm-intel into driver-core-next
Daniel writes:
typed componented support + i915/snd-hda changes
This is needed by the new MEI-HDCP support in i915, so will need to go
in through drm and drivers-misc trees at least.
* tag 'topic/component-typed-2019-02-11' of git://anongit.freedesktop.org/drm/drm-intel:
i915/snd_hdac: I915 subcomponent for the snd_hdac
components: multiple components for a device
component: Add documentation
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix markup warning: insert a blank line before the hint.
Documentation/driver-api/dmaengine/dmatest.rst:63: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While typing these I think doing an s/component_master/aggregate/
would be useful:
- it's shorter :-)
- I think component/aggregate is much more meaningful naming than
component/puppetmaster or something like that. At least to my
English ear "aggregate" emphasizes much more the "assemble a pile of
things into something bigger" aspect, and there's not really much
of a control hierarchy between aggregate and constituing components.
But that's way more than a quick doc typing exercise ...
Thanks to Ram for commenting on an initial draft of these docs.
v2: Review from Rafael:
- git add Documenation/driver-api/component.rst
- lots of polish to the wording + spelling fixes.
v3: Review from Russell:
- s/framework/helper
- clarify the documentation for component_match_add functions.
v4: Remove a few superflous "This".
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "C, Ramalingam" <ramalingam.c@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207232759.14553-1-daniel.vetter@ffwll.ch
If device_link_add() is called twice in a row to create a stateless
device link for the same consumer-supplier pair without an attempt
to delete the link between these calls, and the second caller passes
DL_FLAG_RPM_ACTIVE to it in flags, calling either device_link_del()
or device_link_remove() immediately after that will leave the link's
supplier device with nonzero PM-runtime usage counter, which may
prevent the supplier from being runtime-suspended going forward
until the link is deleted by another invocation of device_link_del()
or device_link_remove() for it.
Even though this is confusing and may lead to subtle issues, trying
to avoid it in the framework also may cause problems to appear, so
document it as a known limitation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.
Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new device link flag, DL_FLAG_AUTOPROBE_CONSUMER, to request the
driver core to probe for a consumer driver automatically after binding
a driver to the supplier device on a persistent managed device link.
As unbinding the supplier driver on a managed device link causes the
consumer driver to be detached from its device automatically, this
flag provides a complementary mechanism which is needed to address
some "composite device" use cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though stateful device links are managed by the driver core in
principle, their creators are allowed and sometimes even expected
to drop references to them via device_link_del() or
device_link_remove(), but that doesn't really play well with the
"persistent" link concept.
If "persistent" managed device links are created from driver
probe callbacks, device_link_add() called to do that will take a
new reference on the link each time the callback runs and those
references will never be dropped, which kind of isn't nice.
This issues arises because of the link reference counting carried
out by device_link_add() for existing links, but that is only done to
avoid deleting device links that may still be necessary, which
shouldn't be a concern for managed (stateful) links. These device
links are managed by the driver core and whoever creates one of them
will need it at least as long as until the consumer driver is detached
from its device and deleting it may be left to the driver core just
fine.
For this reason, rework device_link_add() to apply the reference
counting to stateless links only and make device_link_del() and
device_link_remove() drop references to stateless links only too.
After this change, if called to add a stateful device link for
a consumer-supplier pair for which a stateful device link is
present already, device_link_add() will return the existing link
without incrementing its reference counter. Accordingly,
device_link_del() and device_link_remove() will WARN() and do
nothing when called to drop a reference to a stateful link. Thus,
effectively, all stateful device links will be owned by the driver
core.
In addition, clean up the handling of the link management flags,
DL_FLAG_AUTOREMOVE_CONSUMER and DL_FLAG_AUTOREMOVE_SUPPLIER, so that
(a) they are never set at the same time and (b) if device_link_add()
is called for a consumer-supplier pair with an existing stateful link
between them, the flags of that link will be combined with the flags
passed to device_link_add() to ensure that the life time of the link
is sufficient for all of the callers of device_link_add() for the
same consumer-supplier pair.
Update the device_link_add() kerneldoc comment to reflect the
above changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, it is not valid to add a device link from a consumer
driver ->probe callback to a supplier that is still probing too, but
generally this is a valid use case. For example, if the consumer has
just acquired a resource that can only be available if the supplier
is functional, adding a device link to that supplier right away
should be safe (and even desirable arguably), but device_link_add()
doesn't handle that case correctly and the initial state of the link
created by it is wrong then.
To address this problem, change the initial state of device links
added between a probing supplier and a probing consumer to
DL_STATE_CONSUMER_PROBE and update device_links_driver_bound() to
skip such links on the supplier side.
With this change, if the supplier probe completes first,
device_links_driver_bound() called for it will skip the link state
update and when it is called for the consumer, the link state will
be updated to "active". In turn, if the consumer probe completes
first, device_links_driver_bound() called for it will change the
state of the link to "active" and when it is called for the
supplier, the link status update will be skipped.
However, in principle the supplier or consumer probe may still fail
after the link has been added, so modify device_links_no_driver() to
change device links in the "active" or "consumer probe" state to
"dormant" on the supplier side and update __device_links_no_driver()
to change the link state to "available" only if it is "consumer
probe" or "active".
Then, if the supplier probe fails first, the leftover link to the
probing consumer will become "dormant" and device_links_no_driver()
called for the consumer (when its probe fails) will clean it up.
In turn, if the consumer probe fails first, it will either drop the
link, or change its state to "available" and, in the latter case,
when device_links_no_driver() is called for the supplier, it will
update the link state to "dormant". [If the supplier probe fails,
but the consumer probe succeeds, which should not happen as long as
the consumer driver is correct, the link still will be around, but
it will be "dormant" until the supplier is probed again.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning -EAGAIN is no longer supported by pin_config_group_set()
since ad42fc6c84 ("pinctrl: rip out the direct pinconf API")
Remove the relevant section from the documentation.
Signed-off-by: Ramon Fried <ramon.fried@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the remaining documents under Documentation/cpuidle/
with one more complete governor and driver API document for cpuidle
under Documentation/driver-api/pm/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
dmaengine updates for v4.21-rc1
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers
-----BEGIN PGP SIGNATURE-----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=+pTt
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This includes a new driver, removes R-Mobile APE6 as it is no longer
used, sprd cyclic dma support, last batch of dma_slave_config
direction removal and random updates to bunch of drivers.
Summary:
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers"
* tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (48 commits)
dmaengine: qcom_hidma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: pxa: remove DBGFS_FUNC_DECL()
dmaengine: mic_x100_dma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: amba-pl08x: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: Documentation: Add documentation for multi chan testing
dmaengine: dmatest: Add transfer_size parameter
dmaengine: dmatest: Add alignment parameter
dmaengine: dmatest: Use fixed point div to calculate iops
dmaengine: dmatest: Add support for multi channel testing
dmaengine: rcar-dmac: Document R8A774C0 bindings
dt-bindings: dmaengine: usb-dmac: Add binding for r8a774c0
dmaengine: zynqmp_dma: replace spin_lock_bh with spin_lock_irqsave
dmaengine: sprd: Add me as one of the module authors
dmaengine: sprd: Support DMA 2-stage transfer mode
dmaengine: sprd: Support DMA link-list cyclic callback
dmaengine: sprd: Set cur_desc as NULL when free or terminate one dma channel
dmaengine: sprd: Fix the last link-list configuration
dmaengine: sprd: Get transfer residue depending on the transfer direction
dmaengine: sprd: Remove direction usage from struct dma_slave_config
dmaengine: dmatest: fix a small memory leak in dmatest_func()
...
document on perf security, more Italian translations, more
improvements to the memory-management docs, improvements to the
pathname lookup documentation, and the usual array of smaller
fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlwmSPkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Y9ZoH/joPnMFykOxS0SmdfI7Z+F4EiJct/ZwF9bHx
T673T0RC30IgnUXGmBl5OtktfWqVh9aGqHOGwgh65ybp2QvzemdP0k6Lu6RtwNk9
6LfkpvuUb8FzaQmCHnSMzMSDmXtZUw3Z/mOjCBcQtfGAsUULNT08xl+Dr+gwWIWt
H+gPEEP+MCXTOQO1jm2dHOHW8NGm6XOijMTpOxp/pkoEY5tUxkVB1T//8EeX7LVh
c1QHzFrufE3bmmubCLtIuyVqZbm/V5l6rHREDQ46fnH/G9fM4gojzsrAL/Y2m4bt
E4y0XJHycjLMRDimAnYhbPm1ryTFAX1lNzHP3M/EF6Heqx8YHAk=
=vtwu
-----END PGP SIGNATURE-----
Merge tag 'docs-5.0' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"A fairly normal cycle for documentation stuff. We have a new document
on perf security, more Italian translations, more improvements to the
memory-management docs, improvements to the pathname lookup
documentation, and the usual array of smaller fixes.
As is often the case, there are a few reaches outside of
Documentation/ to adjust kerneldoc comments"
* tag 'docs-5.0' of git://git.lwn.net/linux: (38 commits)
docs: improve pathname-lookup document structure
configfs: fix wrong name of struct in documentation
docs/mm-api: link slab_common.c to "The Slab Cache" section
slab: make kmem_cache_create{_usercopy} description proper kernel-doc
doc:process: add links where missing
docs/core-api: make mm-api.rst more structured
x86, boot: documentation whitespace fixup
Documentation: devres: note checking needs when converting
doc🇮🇹 add some process/* translations
doc🇮🇹 fixes in process/1.Intro
Documentation: convert path-lookup from markdown to resturctured text
Documentation/admin-guide: update admin-guide index.rst
Documentation/admin-guide: introduce perf-security.rst file
scripts/kernel-doc: Fix struct and struct field attribute processing
Documentation: dev-tools: Fix typos in index.rst
Correct gen_init_cpio tool's documentation
Document /proc/pid PID reuse behavior
Documentation: update path-lookup.md for parallel lookups
Documentation: Use "while" instead of "whilst"
dmaengine: Add mailing list address to the documentation
...
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCYxNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl4pQCfaQBjMxPpp6TVcHANZ/O+zE3NH/wAoL11p3IB
KUq8v9pmcHO8sW5TWOJw
=iYGf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (142 commits)
USB: serial: option: add Fibocom NL678 series
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
usb: typec: tcpm: Extend the matching rules on PPS APDO selection
usb: typec: Improve Alt Mode documentation
usb: musb: dsps: fix runtime pm for peripheral mode
usb: musb: dsps: fix otg state machine
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
usb: renesas_usbhs: add support for RZ/G2E
usb: ehci-omap: Fix deferred probe for phy handling
usb: roles: Add a description for the class to Kconfig
usb: renesas_usbhs: mark PM functions as __maybe_unused
usb: core: Remove unnecessary memset()
usb: host: isp1362-hcd: convert to DEFINE_SHOW_ATTRIBUTE
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
...
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
Adding the document to the usb index file and fixing a few
references. Also, exposing the code examples as "literal
blocks" so they are more easy to read.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typos, spellos, and grammar in p2pdma.rst and p2pdma.c.
Fix return value(s) in function pci_p2pmem_alloc_sgl().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Some documents are refering to others without links. With this
patch I add those missing links.
This patch affects only documents under process/ and labels where
necessary.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add Intel Stratix10 service layer driver document
Signed-off-by: Richard Gong <richard.gong@intel.com>
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not the first time I've got a private email in regard to
dmatest.c module.
Motivate people, by adding a note, to send their questions
to the mailing list instead
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add the I3C documentation describing the protocol, the master driver API
and the device driver API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
fpga
stm
extcon
nvmem
eeprom
hyper-v
gsmi
coresight
thunderbolt
vmw_balloon
goldfish
soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9Le5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn+BQCfZ6DtCIgqo0UW3dLV8Fd0wya9kw0AoNglzJJ6
YRZiaSdRiggARpNdh3ME
=97BX
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
- fpga
- stm
- extcon
- nvmem
- eeprom
- hyper-v
- gsmi
- coresight
- thunderbolt
- vmw_balloon
- goldfish
- soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (245 commits)
Documentation/security-bugs: Clarify treatment of embargoed information
lib: Fix ia64 bootloader linkage
MAINTAINERS: Clarify UIO vs UIOVEC maintainer
docs/uio: fix a grammar nitpick
docs: fpga: document programming fpgas using regions
fpga: add devm_fpga_region_create
fpga: bridge: add devm_fpga_bridge_create
fpga: mgr: add devm_fpga_mgr_create
hv_balloon: Replace spin_is_locked() with lockdep
sgi-xp: Replace spin_is_locked() with lockdep
eeprom: New ee1004 driver for DDR4 memory
eeprom: at25: remove unneeded 'at25_remove'
w1: IAD Register is yet readable trough iad sys file. Fix snprintf (%u for unsigned, count for max size).
misc: mic: scif: remove set but not used variables 'src_dma_addr, dst_dma_addr'
misc: mic: fix a DMA pool free failure
platform: goldfish: pipe: Add a blank line to separate varibles and code
platform: goldfish: pipe: Remove redundant casting
platform: goldfish: pipe: Call misc_deregister if init fails
platform: goldfish: pipe: Move the file-scope goldfish_pipe_dev variable into the driver state
platform: goldfish: pipe: Move the file-scope goldfish_pipe_miscdev variable into the driver state
...
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
readability improvements for the formatted output, some LICENSES updates
including the addition of the ISC license, the removal of the unloved and
unmaintained 00-INDEX files, the deprecated APIs document from Kees, more
MM docs from Mike Rapoport, and the usual pile of typo fixes and
corrections.
-----BEGIN PGP SIGNATURE-----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=C0wt
-----END PGP SIGNATURE-----
Merge tag 'docs-4.20' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
Core changes:
* Support non-uniform erase size
* Support controllers with limited TX fifo size
Driver changes:
* m25p80: Re-issue a WREN command after each write access
* cadence: Pass a proper dir value to dma_[un]map_single()
* fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
* intel-spi: Add a new PCI entry for Ice Lake
NAND changes:
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
MTD changes:
* physmap cleanups/fixe
* gpio-addr-flash cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=7w4w
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
As discussed in the "API replacement/deprecation" thread[1], this makes
an effort to document what things shouldn't get (re)added to the kernel,
by introducing Documentation/process/deprecated.rst.
[1] https://lists.linuxfoundation.org/pipermail/ksummit-discuss/2018-September/005282.html
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a restructured text file describing how to write drivers with support
for P2P DMA transactions. The document describes how to use the APIs that
were added in the previous few commits.
Also adds an index for the PCI documentation tree even though this is the
only PCI document that has been converted to restructured text at this
time.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Add a new directory in the driver API guide for PCI-specific documentation.
This is in preparation for adding a new PCI P2P DMA driver writers guide
which will go in this directory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sagar Dharia <sdharia@codeaurora.org>
This patch fixes a minor, incorrect piece of grammar in the UIO howto.
Signed-off-by: Will Korteland <will@korte.land>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clarify the intention that interfaces and upper layers use
regions rather than managers directly.
Rearrange API documentation to better group the API functions
used to create FPGA mgr/bridge/regions and the API used for
programming FPGAs.
Signed-off-by: Alan Tull <atull@kernel.org>
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_fpga_region_create() which is the
managed version of fpga_region_create().
Change current region drivers to use
devm_fpga_region_create().
Signed-off-by: Alan Tull <atull@kernel.org>
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_fpga_bridge_create() which is the managed
version of fpga_bridge_create().
Change current bridge drivers to use
devm_fpga_bridge_create().
Signed-off-by: Alan Tull <atull@kernel.org>
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_fpga_mgr_create() which is the managed
version of fpga_mgr_create().
Change current FPGA manager drivers to use
devm_fpga_mgr_create()
Signed-off-by: Alan Tull <atull@kernel.org>
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Internal helper function gpiod_set_array_value_complex() was changed to
return an error value, but not all gpiolib callers were updated to
propagate the new error up.
Fixes: 3027743f83 ("gpio: Remove VLA from gpiolib")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The return type of gpiod_set_raw_array_value() and
gpiod_set_raw_array_value_cansleep() was changed from void to int, but
the doc update was forgotten.
Fixes: 3027743f83 ("gpio: Remove VLA from gpiolib")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add flags #defines to kerneldoc documentation in a
useful place.
Signed-off-by: Alan Tull <atull@kernel.org>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New code introduced by commit bf9346f5d4 ("gpiolib: Identify arrays
matching GPIO hardware") forcibly tries to find an array member which
has its array index number equal to its hardware pin number and set
up an array info for possible fast bitmap processing of all arrray
pins belonging to that chip which also satisfy that numbering rule.
Depending on array content, it may happen that consecutive array
members which belong to the same chip but don't have array indexes
equal to their pin hardware numbers will be split into groups, some of
them processed together via the fast bitmap path, and rest of them
separetely. However, applications may expect all those pins being
processed together with a single call to .set_multiple() chip callback,
like that was done before the change.
Limit applicability of fast bitmap processing path to cases where all
pins of consecutive array members starting from 0 which belong to the
same chip have their hardware numbers equal to their corresponding
array indexes. That should still speed up processing of applications
using whole GPIO banks as I/O ports, while not breaking simultaneous
manipulation of consecutive pins of the same chip which don't follow
the equal numbering rule.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO descriptor arrays returned by gpio_get_array() may contain
information on direct mapping of array members to pins of a single GPIO
chip in hardware order. In such cases, bitmaps of values can be passed
directly from/to the chip's .get/set_multiple() callbacks without
wasting time on iterations.
Add respective code to gpiod_get/set_array_bitmap_complex() functions.
Pins not applicable for fast path are processed as before, skipping
over the 'fast' ones.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO array lookup results may map directly to GPIO pins of a
single GPIO chip in hardware order. If that condition is recognized
and handled efficiently, significant performance gain of get/set array
functions may be possible.
While processing a request for an array of GPIO descriptors, identify
those which represent corresponding pins of a single GPIO chip. Skip
over pins which require open source or open drain special processing.
Moreover, identify pins which require inversion. Pass a pointer to
that information with the array to the caller so it can benefit from
enhanced performance as soon as get/set array functions can accept and
make efficient use of it.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a basic Firewire/IEEE 1394 driver API chapter to the Linux
kernel documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: linux-doc@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add example and documentation to describe multi link streams
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge issue
reported. That merge issue is in fs/sysfs/group.c and Stephen has
posted the diff of what it should be to resolve this. I'll follow up
with that diff to this pull request.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g86Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyXQCePaZSW8wft4b7nLN8RdZ98ATBru0Ani10lrJa
HQeQJRNbWU1AZ0ym7695
=tOaH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge
issue reported"
* tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (21 commits)
base: core: Remove WARN_ON from link dependencies check
drivers/base: stop new probing during shutdown
drivers: core: Remove glue dirs from sysfs earlier
driver core: remove unnecessary function extern declare
sysfs.h: fix non-kernel-doc comment
PM / Domains: Stop deferring probe at the end of initcall
iommu: Remove IOMMU_OF_DECLARE
iommu: Stop deferring probe at end of initcalls
pinctrl: Support stopping deferred probe after initcalls
dt-bindings: pinctrl: add a 'pinctrl-use-default' property
driver core: allow stopping deferred probe after init
driver core: add a debugfs entry to show deferred devices
sysfs: Fix internal_create_group() for named group updates
base: fix order of OF initialization
linux/device.h: fix kernel-doc notation warning
Documentation: update firmware loader fallback reference
kobject: Replace strncpy with memcpy
drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number
kernfs: Replace strncpy with memcpy
device: Add #define dev_fmt similar to #define pr_fmt
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this development
cycle:
- lots of type-c work, with drivers graduating out of staging,
and displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot
simpler in the future.
- usbserial driver fixes and reworks
- other misc changes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3hBPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloNwCggMZi9m8Krjq7d7aLw5oJJex/nIAAn0jeADOT
NpoCgrtGHjwrATxN5/Ke
=jXa3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
small fixes and updates. We also have new ktime_get_*() docs from Arnd,
some kernel-doc fixes, a new set of Italian translations (non so se vale la
pena, ma non fa male - speriamo bene), and some extensive early
memory-management documentation improvements from Mike Rapoport.
-----BEGIN PGP SIGNATURE-----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=x/P0
-----END PGP SIGNATURE-----
Merge tag 'docs-4.19' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"This was a moderately busy cycle for docs, with the usual collection
of small fixes and updates.
We also have new ktime_get_*() docs from Arnd, some kernel-doc fixes,
a new set of Italian translations (non so se vale la pena, ma non fa
male - speriamo bene), and some extensive early memory-management
documentation improvements from Mike Rapoport"
* tag 'docs-4.19' of git://git.lwn.net/linux: (52 commits)
Documentation: corrections to console/console.txt
Documentation: add ioctl number entry for v4l2-subdev.h
Remove gendered language from management style documentation
scripts/kernel-doc: Escape all literal braces in regexes
docs/mm: add description of boot time memory management
docs/mm: memblock: add overview documentation
docs/mm: memblock: add kernel-doc description for memblock types
docs/mm: memblock: add kernel-doc comments for memblock_add[_node]
docs/mm: memblock: update kernel-doc comments
mm/memblock: add a name for memblock flags enumeration
docs/mm: bootmem: add overview documentation
docs/mm: bootmem: add kernel-doc description of 'struct bootmem_data'
docs/mm: bootmem: fix kernel-doc warnings
docs/mm: nobootmem: fixup kernel-doc comments
mm/bootmem: drop duplicated kernel-doc comments
Documentation: vm.txt: Adding 'nr_hugepages_mempolicy' parameter description.
doc:it_IT: translation for kernel-hacking
docs: Fix the reference labels in Locking.rst
doc: tracing: Fix a typo of trace_stat
mm: Introduce new type vm_fault_t
...
The documentation for this parameter said "6 bytes" when "8 bytes" was
intended; correct it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
ata_sff_data_xfer_noirq() is invoked via the ->sff_data_xfer hook. The
latter is invoked by ata_pio_sector(), atapi_send_cdb() and
__atapi_pio_bytes() which in turn is invoked by ata_sff_hsm_move().
The latter function requires that the "ap->lock" lock is held which
needs to be taken with disabled interrupts.
There is no need have to have ata_sff_data_xfer_noirq() which invokes
ata_sff_data_xfer32() with disabled interrupts because at this point the
interrupts are already disabled.
Remove the function and its references to it and replace all callers
with ata_sff_data_xfer32().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a flag to autoremove the device links on supplier driver
unbind. This obviates the need to explicitly delete the link
in the remove path.
We remove these links only when the supplier's link to its
consumers has gone to DL_STATE_SUPPLIER_UNBIND state.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Suggested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The firmware loader has a fallback mechanism, and it now has some proper
kdoc, but we forgot to update the Documentation to use the new kdoc. Fix
that.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to SLIMbus stream apis for slimbus device.
SLIMbus streaming involves adding support to Data Channel Management and
channel Reconfiguration Messages to slim core plus few stream apis.
>From slim device side the apis are very simple mostly inline with other
stream apis.
Currently it only supports Isochronous and Push/Pull transport protocols,
which are sufficient for audio use cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minor fixes including:
* fix some typos
* correct use of a/an
* rephrase explanation of .state ops function
* s/re-use/reuse/ (use only one spelling of 'reuse' in these docs)
* s/cpu/CPU/
Signed-off-by: Alan Tull <atull@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=PrOL
-----END PGP SIGNATURE-----
Merge tag 'dma-rename-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping rename from Christoph Hellwig:
"Move all the dma-mapping code to kernel/dma and lose their dma-*
prefixes"
* tag 'dma-rename-4.18' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: move all DMA mapping code to kernel/dma
dma-mapping: use obj-y instead of lib-y for generic dma ops
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Currently the code is split over various files with dma- prefixes in the
lib/ and drives/base directories, and the number of files keeps growing.
Move them into a single directory to keep the code together and remove
the file name prefixes. To match the irq infrastructure this directory
is placed under the kernel/ directory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with.
Kudos to Laura Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare
dwapb driver.
Misc:
- Random cleanups, right header files in the drivers, some
size optimizations etc.
-----BEGIN PGP SIGNATURE-----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=Ly/0
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.18 development cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with. Kudos to Laura
Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare dwapb
driver.
Misc:
- Random cleanups, right header files in the drivers, some size
optimizations etc"
* tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpio: davinci: fix build warning when !CONFIG_OF
gpio: dwapb: Fix rework support for 1 interrupt per port A GPIO
gpio: pxa: Include the right header
gpio: pl061: Include the right header
gpio: pch: Include the right header
gpio: pcf857x: Include the right header
gpio: pca953x: Include the right header
gpio: palmas: Include the right header
gpio: omap: Include the right header
gpio: octeon: Include the right header
gpio: mxs: Switch to SPDX identifier
gpio: Remove VLA from stmpe driver
gpio: mxc: Switch to SPDX identifier
gpio: mxc: add clock operation
gpio: Remove VLA from gpiolib
gpio: aspeed: Use a cache of output data registers
gpio: aspeed: Set output latch before changing direction
gpio: pca953x: fix address calculation for pcal6524
gpio: pca953x: define masks for addressing common and extended registers
gpio: pca953x: set the PCA_PCAL flag also when matching by DT
...
Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to be
able to understand the firmware code better. There's also a user for a
new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykbiACgu/2qqou1iV4GxOkvrj5wfsHD+lYAoNPNNDHu
Qf3CCEKbxogF6YowDiAH
=Dsqq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to
be able to understand the firmware code better. There's also a user
for a new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
driver core: hold dev's parent lock when needed
driver-core: return EINVAL error instead of BUG_ON()
driver core: add __printf verification to device_create_groups_vargs
mm: memory_hotplug: use put_device() if device_register fail
base: core: fix typo 'can by' to 'can be'
debugfs: inode: debugfs_create_dir uses mode permission from parent
debugfs: Re-use kstrtobool_from_user()
Documentation: clarify firmware_class provenance and why we can't rename the module
Documentation: remove stale firmware API reference
Documentation: fix few typos and clarifications for the firmware loader
ath10k: re-enable the firmware fallback mechanism for testmode
ath10k: use firmware_request_nowarn() to load firmware
firmware: add firmware_request_nowarn() - load firmware without warnings
firmware_loader: make firmware_fallback_sysfs() print more useful
firmware_loader: move kconfig FW_LOADER entries to its own file
firmware_loader: replace ---help--- with help
firmware_loader: enhance Kconfig documentation over FW_LOADER
firmware_loader: document firmware_sysfs_fallback()
firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
firmware: use () to terminate kernel-doc function names
...
Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbXfQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymwCACdFbUy2kWwrpZWSfSBpawfrs75lLMAmwVOe+62
9aDsDWzDVUEFxF20qiE6
=CMJ3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
vmw_balloon: fixing double free when batching mode is off
MAINTAINERS: Add driver-api/fpga path
fpga: clarify that unregister functions also free
documentation: fpga: move fpga-region.txt to driver-api
documentation: fpga: add bridge document to driver-api
documentation: fpga: move fpga-mgr.txt to driver-api
Documentation: fpga: move fpga overview to driver-api
fpga: region: kernel-doc fixes
fpga: bridge: kernel-doc fixes
fpga: mgr: kernel-doc fixes
fpga: use SPDX
fpga: region: change api, add fpga_region_create/free
fpga: bridge: change api, don't use drvdata
fpga: manager: change api, don't use drvdata
fpga: region: don't use drvdata in common fpga code
Drivers: hv: vmbus: Removed an unnecessary cast from void *
ver_linux: Drop redundant calls to system() to test if file is readable
ver_linux: Move stderr redirection from function parameter to function body
misc: IBM Virtual Management Channel Driver (VMC)
rpmsg: Correct support for MODULE_DEVICE_TABLE()
...
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script to
keep it updated.
- Various LICENSES updates from Thomas, along with a script to check SPDX
tags.
- Work to fix dangling references to documentation files; this involved a
fair number of one-liner comment changes outside of Documentation/
...and the usual list of documentation improvements, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----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=I6FG
-----END PGP SIGNATURE-----
Merge tag 'docs-4.18' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of work in the docs tree this time around,
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script
to keep it updated.
- Various LICENSES updates from Thomas, along with a script to check
SPDX tags.
- Work to fix dangling references to documentation files; this
involved a fair number of one-liner comment changes outside of
Documentation/
... and the usual list of documentation improvements, typo fixes, etc"
* tag 'docs-4.18' of git://git.lwn.net/linux: (103 commits)
Documentation: document hung_task_panic kernel parameter
docs/admin-guide/mm: add high level concepts overview
docs/vm: move ksm and transhuge from "user" to "internals" section.
docs: Use the kerneldoc comments for memalloc_no*()
doc: document scope NOFS, NOIO APIs
docs: update kernel versions and dates in tables
docs/vm: transhuge: split userspace bits to admin-guide/mm/transhuge
docs/vm: transhuge: minor updates
docs/vm: transhuge: change sections order
Documentation: arm: clean up Marvell Berlin family info
Documentation: gpio: driver: Fix a typo and some odd grammar
docs: ranoops.rst: fix location of ramoops.txt
scripts/documentation-file-ref-check: rewrite it in perl with auto-fix mode
docs: uio-howto.rst: use a code block to solve a warning
mm, THP, doc: Add document for thp_swpout/thp_swpout_fallback
w1: w1_io.c: fix a kernel-doc warning
Documentation/process/posting: wrap text at 80 cols
docs: admin-guide: add cgroup-v2 documentation
Revert "Documentation/features/vm: Remove arch support status file for 'pte_special'"
Documentation: refcount-vs-atomic: Update reference to LKMM doc.
...
Move Documentation/fpga/fpga-region.txt to
driver-api/fpga/fpga-region.rst. Including:
- Add it to driver-api/fpga/index.rst
- Formatting changes to build cleanly as ReST documentation
- Some rewrites for better flow as a ReST doc such as moving
API reference to the end of the doc
- Rewrite API reference section to refer to kernel-doc
documentation in fpga-region.c driver code
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new document to driver-api/fpga that documents the
fpga bridge API and add it to driver-api/fpga/index.rst
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move Documentation/fpga/fpga-mgr.txt to driver-api/fpga/fpga-mgr.rst
and:
- Add to driver-api/fpga/index.rst
- Format changes so documentation builds cleanly.
- Minor rewrites that make the doc flow better as ReST documentation.
- Such as moving API reference to end of doc
- Change API reference section to refer to kernel-doc documentation in
fpga-mgr.c driver code rather than statically defining each function.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start of moving Documentation/fpga/*.txt to driver-api, including:
- Add new directory driver-api/fpga
- Add new file driver-api/fpga/index.rst
- Add driver-api/fpga to driver-api/index.rst
- Move Documentation/fpga/overview.txt to driver-api/fpga/intro.rst
- Formatting and rewrites so that intro.rst will build cleanly
and form a good introduction to the rest of the docs to be added.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=b56m
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Board files constitute a significant part of the users of the legacy
GPIO framework. In many cases they only export a line and set its
desired value. We could use GPIO hogs for that like we do for DT and
ACPI but there's no support for that in machine code.
This patch proposes to extend the machine.h API with support for
registering hog tables in board files.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pointer to the CEC GPIO driver from the GPIO list of
examples of drivers on top of GPIO.
Cc: linux-media@vger.kernel.org
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clarify the provenance of the firmware loader firmware_class module name
and why we cannot rename the module in the future.
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a few typos, and clarify a few sentences.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the firmware loader only exposes one silent path for querying
optional firmware, and that is firmware_request_direct(). This function
also disables the sysfs fallback mechanism, which might not always be the
desired behaviour [0].
This patch introduces a variations of request_firmware() that enable the
caller to disable the undesired warning messages but enables the sysfs
fallback mechanism. This is equivalent to adding FW_OPT_NO_WARN to the
old behaviour.
[0]: https://git.kernel.org/linus/c0cc00f250e1
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
[mcgrof: used the old API calls as the full rename is not done yet, and
add the caller for when FW_LOADER is disabled, enhance documentation ]
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This contains:
- Support for SoundWire Streaming
- Documentation updates for streaming
- Cadence and Intel driver updates for streaming
- ASoC API for programming soundwire stream
-----BEGIN PGP SIGNATURE-----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=KZwI
-----END PGP SIGNATURE-----
Merge tag 'soundwire-streaming' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire streaming
This contains:
- Support for SoundWire Streaming
- Documentation updates for streaming
- Cadence and Intel driver updates for streaming
- ASoC API for programming soundwire stream
The clk.rst is already in ReST format. So, move it to the
driver-api guide, where it belongs.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A number of new docs were added, but they're currently not on
the index.rst from the session they're supposed to be, causing
Sphinx warnings.
Add them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Using incorrect :functions: syntax (extra space) causes an odd kernel-doc
warning, so fix that.
Documentation/driver-api/device_connection.rst:42: ERROR: Error in "kernel-doc" directive:
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce the
number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuMxrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFpQCg1JM62/W8e6mQ4vdZNQmAzgMKMEMAniOMcVRX
/oDWXp64mYwJu+GTxnIJ
=+9Gk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are some small driver core and firmware fixes for 4.17-rc3
There's a kobject WARN() removal to make syzkaller a lot happier about
some "normal" error paths that it keeps hitting, which should reduce
the number of false-positives we have been getting recently.
There's also some fimware test and documentation fixes, and the
coredump() function signature change that needed to happen after -rc1
before drivers started to take advantage of it.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: some documentation fixes
selftests:firmware: fixes a call to a wrong function name
kobject: don't use WARN for registration failures
firmware: Fix firmware documentation for recent file renames
test_firmware: fix setting old custom fw path back on exit, second try
test_firmware: Install all scripts
drivers: change struct device_driver::coredump() return type to void
Including:
- Fixup outdated kernel-doc paths
- Slightly too short title underline
- Some typos
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
firmware_class.c was split into several files under
drivers/base/firmware_loader. The new main.c has the functions which
/request_firmware.rst references.
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using reStructuredText literal-block element with ascii-art.
That prevents the ascii art from being processed as
reStructuredText.
Reported-by: Masanari Iida <standby24x7@gmail.com>
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver-api document for target/iSCSI interfaces.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
To: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using reStructuredText literal-block element with ascii-art.
That prevents the ascii art from being processed as
reStructuredText.
Reported-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-and-tested-by: Jani Nikula <jani.nikula@intel.com>
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Core:
* Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
* Remove Cyrille from the list of SPI NOR and MTD maintainers
* Fix kernel doc headers
* Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
* Remove the bfin-async-flash driver (the only architecture using
it has been removed)
* Fix pagetest test
* Add extra checks in mtd_erase()
* Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
Drivers:
* Add endianness information to the physmap DT binding
* Add Eon EN29LV400A IDs to JEDEC probe logic
* Use %*ph where appropriate
SPI NOR changes:
Drivers:
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND changes:
Core:
* Prepare arrival of the SPI NAND subsystem by implementing a
generic (interface-agnostic) layer to ease manipulation of NAND
devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Drivers:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=EG7L
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas. In addition we have removed several really
old drivers: sym53c416, NCR53c406a, fdomain, fdomain_cs and removed
the old scsi_module.c initialization from all remaining drivers. Plus
an assortment of bug fixes, initialization errors and other minor
fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWsVSnSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbvbAP9ErpTZ
OR5iJ5HIz4W3Bd8aTfEpJrDyeYwSUC+sra5SKQD/ZWyVB3fYFSg+ZROyT26pmtmd
SdImhG7hLaHgVvF5qRQ=
=SQ/n
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code refactoring
from Luis as he attempts to wrangle that codebase into something that is
managable, along with a bunch of userspace tests for it. Other than
that, a handful of small bugfixes and reverts of things that didn't work
out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSiGg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylPpACgyEKOur8rwp/3uBRxqhoFeWp1RtAAoIvlMjn6
MQ8LIeHNLRnpqGX5L78L
=93HA
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 4.17-rc1.
There's really not much here, just a bunch of firmware code
refactoring from Luis as he attempts to wrangle that codebase into
something that is managable, along with a bunch of userspace tests for
it. Other than that, a handful of small bugfixes and reverts of things
that didn't work out.
Full details are in the shortlog, it's not all that much.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
drivers: base: remove check for callback in coredump_store()
mt7601u: use firmware_request_cache() to address cache on reboot
firmware: add firmware_request_cache() to help with cache on reboot
firmware: fix typo on pr_info_once() when ignore_sysfs_fallback is used
firmware: explicitly include vmalloc.h
firmware: ensure the firmware cache is not used on incompatible calls
test_firmware: modify custom fallback tests to use unique files
firmware: add helper to check to see if fw cache is setup
firmware: fix checking for return values for fw_add_devm_name()
rename: _request_firmware_load() fw_load_sysfs_fallback()
test_firmware: test three firmware kernel configs using a proc knob
test_firmware: expand on library with shared helpers
firmware: enable to force disable the fallback mechanism at run time
firmware: enable run time change of forcing fallback loader
firmware: move firmware loader into its own directory
firmware: split firmware fallback functionality into its own file
firmware: move loading timeout under struct firmware_fallback_config
firmware: use helpers for setting up a temporary cache timeout
firmware: simplify CONFIG_FW_LOADER_USER_HELPER_FALLBACK further
drivers: base: add description for .coredump() callback
...
Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSpJw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylGawCdED2xS3HUxOIqfh81d8B1py8ji04AoJXdLAsH
JgwXbdbibZBabYTVi5s5
=LrRH
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (250 commits)
Revert "USB: serial: ftdi_sio: add Id for Physik Instrumente E-870"
usb: musb: gadget: misplaced out of bounds check
usb: chipidea: imx: Fix ULPI on imx53
usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
usb: chipidea: usbmisc: small clean up
usb: chipidea: usbmisc: evdo can be set e/o reset
usb: chipidea: usbmisc: evdo is only specific to OTG port
USB: serial: ftdi_sio: add Id for Physik Instrumente E-870
usb: dwc3: gadget: never call ->complete() from ->ep_queue()
usb: gadget: udc: core: update usb_ep_queue() documentation
usb: host: Remove the deprecated ATH79 USB host config options
usb: roles: Fix return value check in intel_xhci_usb_probe()
USB: gadget: f_midi: fixing a possible double-free in f_midi
usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
usb: core: Copy parameter string correctly and remove superfluous null check
USB: announce bcdDevice as well as idVendor, idProduct.
USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw
usb: hub: Reduce warning to notice on power loss
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
USB: serial: cp210x: add ELDAT Easywave RX09 id
...
- Lots of work aligning Documentation/ABI with reality, done by Aishwarya
Pant.
- The trace documentation has been converted to RST by Changbin Du
- I thrashed up kernel-doc to deal with a parsing issue and to try to make
the code more readable. It's still a 20+-year-old Perl hack, though.
- Lots of other updates, typo fixes, and more.
-----BEGIN PGP SIGNATURE-----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=QQ/a
-----END PGP SIGNATURE-----
Merge tag 'docs-4.17' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of activity in Documentation/ this time
around:
- Lots of work aligning Documentation/ABI with reality, done by
Aishwarya Pant.
- The trace documentation has been converted to RST by Changbin Du
- I thrashed up kernel-doc to deal with a parsing issue and to try to
make the code more readable. It's still a 20+-year-old Perl hack,
though.
- Lots of other updates, typo fixes, and more"
* tag 'docs-4.17' of git://git.lwn.net/linux: (82 commits)
Documentation/process: update FUSE project website
docs: kernel-doc: fix parsing of arrays
dmaengine: Fix spelling for parenthesis in dmatest documentation
dmaengine: Make dmatest.rst indeed reST compatible
dmaengine: Add note to dmatest documentation about supported channels
Documentation: magic-numbers: Fix typo
Documentation: admin-guide: add kvmconfig, xenconfig and tinyconfig commands
Input: alps - Update documentation for trackstick v3 format
Documentation: Mention why %p prints ptrval
COPYING: use the new text with points to the license files
COPYING: create a new file with points to the Kernel license files
Input: trackpoint: document sysfs interface
xfs: Change URL for the project in xfs.txt
char/bsr: add sysfs interface documentation
acpi: nfit: document sysfs interface
block: rbd: update sysfs interface
Documentation/sparse: fix typo
Documentation/CodingStyle: Add an example for braces
docs/vm: update 00-INDEX
kernel-doc: Remove __sched markings
...
Fix spelling for parenthesis in dmatest documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ jc: did s/parenthesis/parentheses/ and reflowed ]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Make dmatest.rst indeed reST compatible.
Achieve this by fixing several formatting issues.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The documentation is not so clear for newbies in a sense of what type of the
channels are supported by it.
Clarify this by adding a note at the preamble of the documentation.
Reported-by: "Zhu, Tony" <tony.zhu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The blackfin architecture is getting removed, so we can clean up
all the special cases in the musb driver.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Bin Liu <b-liu@ti.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
[arnd: adding in fixups from Aaron and Stephen]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move gpio/drivers-on-gpio.txt to driver-api/gpio/drivers-on-gpio.rst and
make sure it builds cleanly as ReST.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio/board.txt to driver-api/gpio/board.rst and make sure it builds
cleanly as ReST.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio/consumer.txt to driver-api/gpio/consumer.rst and make sure it
builds cleanly as ReST.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio/gpio-legacy.txt to driver-api/gpio/legacy.rst and make sure it
builds cleanly as ReST.
Also move the legacy API reference from index.rst to legacy.rst.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio/driver.txt to driver-api/gpio/driver.rst and make sure it
builds cleanly as ReST.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio/intro.txt to driver-api/gpio/intro.rst and make sure it builds
cleanly as ReST.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To make space for more files in the GPIO section, create a
Documentation/driver-api/gpio/ directory.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices have an optimization in place to enable the firmware to
be retaineed during a system reboot, so after reboot the device can skip
requesting and loading the firmware. This can save up to 1s in load
time. The mt7601u 802.11 device happens to be such a device.
When these devices retain the firmware on a reboot and then suspend
they can miss looking for the firmware on resume. To help with this we
need a way to cache the firmware when such an optimization has taken
place.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Type-C connectors consist of various muxes and switches
that route the pins on the connector to the right locations.
The USB Type-C drivers need to be able to control the muxes,
as they are the ones that know things like the cable plug
orientation, and the current mode that was negotiated with
the partner.
This introduces a small API for registering and controlling
cable plug orientation switches, and separate small API for
registering and controlling pin multiplexer/demultiplexer
switches that are needed with Accessory/Alternate Modes.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several frameworks - clk, gpio, phy, pmw, etc. - maintain
lookup tables for describing connections and provide custom
API for handling them. This introduces a single generic
lookup table and API for the connections.
The motivation for this commit is centralizing the
connection lookup, but the goal is to ultimately extract the
connection descriptions also from firmware by using the
fwnode_graph_* functions and other mechanisms that are
available.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reflects much clearer what is being done.
While at it, kdoc'ify it.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After more than 15 years all users of this legacy interface are finally
gone. Rest in peace!
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use sysfs to allow supporting sub-channels. The userspace application
makes request to host to create sub-channels and the UIO kernel
driver populates the sysfs per-channel directory with a binary
attribute file that can be used to read/write ring.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a warning during "make xmldocs"
Documentation/driver-api/slimbus.rst:93:
WARNING: Title underline too short.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Also mention the iv helpers as well.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since the original inception of the s390-drivers document, the
common I/O layer has grown support for more types of subchannels.
Give at least a pointer for the various types.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
documentation, errseq documentation, kernel-doc support for nested
structure definitions, the removal of lots of crufty kernel-doc support for
unused formats, SPDX tag documentation, the beginnings of a manual for
subsystem maintainers, and lots of fixes and updates.
As usual, some of the changesets reach outside of Documentation/ to effect
kerneldoc comment fixes. It also adds the new LICENSES directory, of which
Thomas promises I do not need to be the maintainer.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJab11TAAoJEI3ONVYwIuV6i1UP/1LgGPHW9Ygq5qaLFbReZd/u
Mx/orrhHX0PdkbCCE+CbL8Vm1m4UKFDTBdlpk3s542zxeeG0ZBXuTnvq4Kyk+cTN
p4/vsIEzk/Ih13/glGE5MlV+EjiEK+8hK69TIUj7bAyuHmpzofjRz9/1M6RLDGDC
HY6UI58AXG0yOQWMWCGRMYpQAFUGij2equ7Doe1ugXRq14dx7V4RsOhI140iRk7t
bquAq1rS2fXniiuPFmLBUe4dWW28isVa/Vl/aXcaWQDKMyT0OLhjOMW36wWKqtPi
WdVCpHv1NLZNyZZr9S3kvfOwW+BUqpEzfVwssyBLW4h0tsnIx0U0HVhSTY8/TvFZ
QD9yCSana4LB/e5CHXIX5lBHbjHxf+rETXqVV4MgwDaMvM3mCo4X6WUTJDmZADo6
vQISEKeb4su5uWAbc9T9xwRSLhZnFVdJ/QuYdNQ5+EpFJYLhzQ9eBvEz6JstSIXL
p9ASBiPNY3ulpVZ8q0JOHJRBhq5mHJH6Dy8achzbILy2l/ZI4b8lJ53mw9II04cp
puF96E6HpvuZ8Tgjjrg9U3ZdxXNrUgc/tjk2ZDkyTglk1XF2jKSq2tiNSZ3oLrJm
XqJPnpCeyJM5UDvwkIBzgC41WEHwe8uvoNbUnc4X7UJSZegFzcSLQXf5qaprHS5k
XeQ7sbd+S+jzVVjFi0W5
=Z15Z
-----END PGP SIGNATURE-----
Merge tag 'docs-4.16' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"Documentation updates for 4.16.
New stuff includes refcount_t documentation, errseq documentation,
kernel-doc support for nested structure definitions, the removal of
lots of crufty kernel-doc support for unused formats, SPDX tag
documentation, the beginnings of a manual for subsystem maintainers,
and lots of fixes and updates.
As usual, some of the changesets reach outside of Documentation/ to
effect kerneldoc comment fixes. It also adds the new LICENSES
directory, of which Thomas promises I do not need to be the
maintainer"
* tag 'docs-4.16' of git://git.lwn.net/linux: (65 commits)
linux-next: docs-rst: Fix typos in kfigure.py
linux-next: DOC: HWPOISON: Fix path to debugfs in hwpoison.txt
Documentation: Fix misconversion of #if
docs: add index entry for networking/msg_zerocopy
Documentation: security/credentials.rst: explain need to sort group_list
LICENSES: Add MPL-1.1 license
LICENSES: Add the GPL 1.0 license
LICENSES: Add Linux syscall note exception
LICENSES: Add the MIT license
LICENSES: Add the BSD-3-clause "Clear" license
LICENSES: Add the BSD 3-clause "New" or "Revised" License
LICENSES: Add the BSD 2-clause "Simplified" license
LICENSES: Add the LGPL-2.1 license
LICENSES: Add the LGPL 2.0 license
LICENSES: Add the GPL 2.0 license
Documentation: Add license-rules.rst to describe how to properly identify file licenses
scripts: kernel_doc: better handle show warnings logic
fs/*/Kconfig: drop links to 404-compliant http://acl.bestbits.at
doc: md: Fix a file name to md-fault.c in fault-injection.txt
errseq: Add to documentation tree
...
This cycle we have small update for:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- Add support for race free transfer termination and updating
for users for that
- Support for new rev of hidma with addition new APIs to
get device match data in ACPI/OF
- Random updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7bH/
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time is smallish update with updates mainly to drivers:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- add support for race free transfer termination and updating for
users for that
- support for new rev of hidma with addition new APIs to get device
match data in ACPI/OF
- random updates to bunch of other drivers"
* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
dmaengine: dmatest: fix container_of member in dmatest_callback
dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
dmaengine: qcom_hidma: simplify DT resource parsing
dmaengine: xilinx_dma: Free BD consistent memory
dmaengine: xilinx_dma: Fix warning variable prev set but not used
dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
dmaengine: doc: format struct fields using monospace
dmaengine: doc: fix bullet list formatting
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
dmaengine: cppi41: Fix channel queues array size check
dmaengine: imx-sdma: Add MODULE_FIRMWARE
dmaengine: xilinx_dma: Fix typos
dmaengine: xilinx_dma: Differentiate probe based on the ip type
dmaengine: xilinx_dma: fix style issues from checkpatch
dmaengine: xilinx_dma: Fix kernel doc warnings
dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
dmaengine: zynqmp_dma: Fix race condition in the probe
...
This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas. We also have a rework of the libsas hotplug handling to
make it more robust, a slew of 32 bit time conversions and fixes, and
a host of the usual minor updates and style changes. The biggest
potential for regressions is the libsas hotplug changes, but so far
they seem stable under testing.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnH+5SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWxuAP0UvuJp
MNR/yU/wv/emSzOc48Ldwd7I0xD2XxSnloGUgwD+IGZZT5yNUQA1THCbm+en4hkB
WvyBieQs9qRit+2czd4=
=gJMf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver
PM flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of
genpd (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the
ACPI core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal
and clean up the governor management code in the cpufreq core
(Rafael Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id
from the PSCI driver and drop dependency on arm_big_little from
the SCPI cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=dnb7
-----END PGP SIGNATURE-----
Merge tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
We've removed the option, so stop talking about it.
Signed-off-by: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host rescinds the device, the UIO driver will clear the interrupt
state and notify application. The read (or write) on the interrupt FD
will then fail with -EIO. This is simpler than adding lots extra uevent
stuff inside UIO.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Map in receive and send buffers for networking in UIO device.
These buffers are special and need to be setup by kernel
API's; userspace can not do it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe the regions present with uio_hv_generic in documentation for
driver API.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vmbus sysfs file names changed in
commit f6b2db084b ("vmbus: make sysfs names consistent with PCI")
and the uio documenatation does not match the current names.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a section about the Hardware consumer
API of the IIO subsystem to the driver API
documentation.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix a spelling typo found in fallback-mechanisms.rst
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Monospace is more readable and is also used elsewhere in the docs.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bullet list documenting the 'struct dma_device' fields has several
nesting errors, making it render improperly. It also has incoherent
formatting: some fields have a description in the same bullet, some in
a sub-bullet.
Fix both to have a correct and coherent formatting.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make the PM core handle DPM_FLAG_LEAVE_SUSPENDED directly for
devices whose "noirq", "late" and "early" driver callbacks are
invoked directly by it.
Namely, make it skip all of the system-wide resume callbacks for
such devices with DPM_FLAG_LEAVE_SUSPENDED set if they are in
runtime suspend during the "noirq" phase of system-wide suspend
(or analogous) transitions or the system transition under way is
a proper suspend (rather than anything related to hibernation) and
the device's wakeup settings are compatible with runtime PM (that
is, the device cannot generate wakeup signals at all or it is
allowed to wake up the system from sleep).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the PM core avoid invoking the "late" and "noirq" system-wide
suspend (or analogous) callbacks provided by device drivers directly
for devices with DPM_FLAG_SMART_SUSPEND set that are in runtime
suspend during the "late" and "noirq" phases of system-wide suspend
(or analogous) transitions. That is only done for devices without
any middle-layer "late" and "noirq" suspend callbacks (to avoid
confusing the middle layer if there is one).
The underlying observation is that runtime PM is disabled for devices
during the "late" and "noirq" system-wide suspend phases, so if they
remain in runtime suspend from the "late" phase forward, it doesn't
make sense to invoke the "late" and "noirq" callbacks provided by
the drivers for them (arguably, the device is already suspended and
in the right state). Thus, if the remaining driver suspend callbacks
are to be invoked directly by the core, they can be skipped.
This change really makes it possible for, say, platform device
drivers to re-use runtime PM suspend and resume callbacks by
pointing ->suspend_late and ->resume_early, respectively (and
possibly the analogous hibernation-related callback pointers too),
to them without adding any extra "is the device already suspended?"
type of checks to the callback routines, as long as they will be
invoked directly by the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update Documentation/driver-api/usb/usb3-debug-port.rst. This update
includes the guide for using xHCI debug capability based TTY serial
link.
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
SoundWire is a new Linux bus which implements a new MIPI bus protocol
'SoundWire'. The summary of SoundWire bus and API is documented in the
'summary' file.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.
The summary of SLIMbus and API is documented in the 'summary' file.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add exported functions from scsi_common.c to the SCSI driver API
documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some functions from refcount_t API provide different
memory ordering guarantees that their atomic counterparts.
This adds a document outlining these differences (
Documentation/core-api/refcount-vs-atomic.rst) as well as
some other minor improvements.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This link is dead:
$ curl -vI http://usb.cs.tum.edu/usbdoc
* Could not resolve host: usb.cs.tum.edu
* Closing connection 0
curl: (6) Could not resolve host: usb.cs.tum.edu
I found the document somewhere else. Let's replace it.
Signed-off-by: Stefan Tatschner <stefan.tatschner@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The pci/htirq.c file was removed so remove it from the documentation
file also.
Error: Cannot open file ../drivers/pci/htirq.c
WARNING: kernel-doc '../scripts/kernel-doc -rst -enable-lineno -export ../drivers/pci/htirq.c' failed with return code 2
Fixes: fd2fa6c18b ("x86/PCI: Remove unused HyperTransport interrupt support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fix following warning during 'make xmldocs'
Documentation/driver-api/dmaengine/client.rst:188:
WARNING: Title underline too short.
Further APIs:
------------
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Define and document a new driver flag, DPM_FLAG_LEAVE_SUSPENDED, to
instruct the PM core and middle-layer (bus type, PM domain, etc.)
code that it is desirable to leave the device in runtime suspend
after system-wide transitions to the working state (for example,
the device may be slow to resume and it may be better to avoid
resuming it right away).
Generally, the middle-layer code involved in the handling of the
device is expected to indicate to the PM core whether or not the
device may be left in suspend with the help of the device's
power.may_skip_resume status bit. That has to happen in the "noirq"
phase of the preceding system suspend (or analogous) transition.
The middle layer is then responsible for handling the device as
appropriate in its "noirq" resume callback which is executed
regardless of whether or not the device may be left suspended, but
the other resume callbacks (except for ->complete) will be skipped
automatically by the core if the device really can be left in
suspend.
The additional power.must_resume status bit introduced for the
implementation of this mechanisn is used internally by the PM core
to track the requirement to resume the device (which may depend on
its children etc).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume
and clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler
on ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core
and drop legacy bus type suspend and resume callbacks from
ARM/locomo (Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up
somewhat (Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle)
residency counter based on the LPIT ACPI table on Intel
platforms (Srinivas Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the
notifier removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use
stale cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing
wakeup events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent
the PM core from using the direct-complete optimization with
it as that is guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit
(Gaurav Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it
up (Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in
the cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches,
Rafael Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava,
Shuah Khan).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QTnx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
* pm-core:
ACPI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Take SMART_SUSPEND driver flag into account
PCI / PM: Drop unnecessary invocations of pcibios_pm_ops callbacks
PM / core: Add SMART_SUSPEND driver flag
PCI / PM: Use the NEVER_SKIP driver flag
PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags
PM / core: Convert timers to use timer_setup()
PM / core: Fix kerneldoc comments of four functions
PM / core: Drop legacy class suspend/resume operations
* pm-sleep:
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
PM / sleep: Remove pm_complete_with_resume_check()
PM: ARM: locomo: Drop suspend and resume bus type callbacks
PM: Use a more common logging style
PM: Document rules on using pm_runtime_resume() in system suspend callbacks
Define and document a SMART_SUSPEND flag to instruct bus types and PM
domains that the system suspend callbacks provided by the driver can
cope with runtime-suspended devices, so from the driver's perspective
it should be safe to leave devices in runtime suspend during system
suspend.
Setting that flag may also cause middle-layer code (bus types,
PM domains etc.) to skip invocations of the ->suspend_late and
->suspend_noirq callbacks provided by the driver if the device
is in runtime suspend at the beginning of the "late" phase of
the system-wide suspend transition, in which case the driver's
system-wide resume callbacks may be invoked back-to-back with
its ->runtime_suspend callback, so the driver has to be able to
cope with that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
This converts and moves pxa_dma file with some format
changes for RST style
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This converts and moves dmatest file with some format
changes for RST style
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This converts and moves client API file with some format
changes for RST style
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This moves and converts provider file with some format changes
for RST style
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This removes the index file and adds the index.rst as placeholder
and update driver-api index to add dmaengine. As a consequence
dmaengine documentation will be in driver-api/
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There is one word too many under formatting markup in one place
in device.rst, so fix it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merging this brings in the timer_setup() change, which allows
me to apply Kees's mac80211 changes for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It quite often is necessary to resume devices from runtime suspend
during system suspend for various reasons (for example, if their
wakeup settings need to be changed), but that requires middle-layer
or subsystem code to follow additional rules which currently are not
clearly documented.
Namely, if a driver calls pm_runtime_resume() for the device from
its ->suspend (or equivalent) system sleep callback, that may not
work if the middle layer above it has updated the state of the
device from its ->prepare or ->suspend callbacks already in an
incompatible way. For this reason, all middle layers must follow
the rule that, until the ->suspend callback provided by the device's
driver is invoked, the only way in which the device's state can be
updated is by calling pm_runtime_resume() for it, if necessary.
Fortunately enough, all middle layers in the code base today follow
this rule, but it is not explicitly stated anywhere, so do that.
Note that calling pm_runtime_resume() from the ->suspend callback
of a driver will cause the ->runtime_resume callback provided by the
middle layer to be invoked, but the rule above guarantees that this
callback will nest properly with the middle layer's ->suspend
callback and it will play well with the ->prepare one invoked before.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function hasn't been used since the removal of iwmc3200wifi
in 2012. It also appears to have a bug when qos=True, since then
it'll copy uninitialized stack memory to the SKB.
Just remove the function entirely.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drop an excess "`" from Documentation/driver-api/pm/devices.rst.
Fixes: 2728b2d2e5 (PM / core / docs: Convert sleep states API document to reST)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 81f9507628.
It causes random failures of firmware loading at resume time (well,
random for me, it seems to be more reliable for others) because the
firmware disabling is not actually synchronous with any particular
resume event, and at least the btusb driver that uses a workqueue to
load the firmware at resume seems to occasionally hit the "firmware
loading is disabled" logic because the firmware loader hasn't gotten the
resume event yet.
Some kind of sanity check for not trying to load firmware when it's not
possible might be a good thing, but this commit was not it.
Greg seems to have silently suffered the same issue, and pointed to the
likely culprit, and Gabriel C verified the revert fixed it for him too.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Pointed-at-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Gabriel C <nix.or.die@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----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=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
Core changes
- Allow the GPIO irqchip to allocate IRQs dynamically. This is
an important change on systems where only a restricted number
of IRQs, lesser than the number of GPIO lines, can be utilized.
Now we can allocate these on a first-come-first-served basis
instead of hogging up valuable IRQ lines.
- Serious fix-up of the kerneldoc documentation and inclusion
into the kerneldoc builds.
- Pulled in the IRQ simulator from the IRQ core tree and use
this in the GPIO mockup driver for exhaustive testing of
interrupt abilities.
New drivers
- New driver for ThunderX and OCTEON-TX. This is especially
interesting as it picks up improvements from the IRQ core that
allow us to handle fasteoi ACKs upwards in a hierarchy when
there are IRQ flag latches on several levels in a hierarchy.
Very interesting work here.
- New subdriver for Renesas R-Car r8a7745 (RZ/G1E).
Misc
- Several fixes and improvements for Xilinx Zynq GPIO.
- Support an enablement GPIO for the 74x164 GPIO.
- Switch a bunch of chips to use devres to allocate irq
descriptors.
- A bunch of constification fixes.
-----BEGIN PGP SIGNATURE-----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=TYNw
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v4.14 cycle.
Not so much changes this time, phew. David Daney and Bartosz
Golaszewski did all the really interesting work in infrastructure
improvement across GPIO and IRQ core, hats off for them and to tglx
and Marc Z for general help with these patch sets.
Core changes:
- Allow the GPIO irqchip to allocate IRQs dynamically. This is an
important change on systems where only a restricted number of IRQs,
lesser than the number of GPIO lines, can be utilized. Now we can
allocate these on a first-come-first-served basis instead of
hogging up valuable IRQ lines.
- Serious fix-up of the kerneldoc documentation and inclusion into
the kerneldoc builds.
- Pulled in the IRQ simulator from the IRQ core tree and use this in
the GPIO mockup driver for exhaustive testing of interrupt
abilities.
New drivers:
- New driver for ThunderX and OCTEON-TX. This is especially
interesting as it picks up improvements from the IRQ core that
allow us to handle fasteoi ACKs upwards in a hierarchy when there
are IRQ flag latches on several levels in a hierarchy. Very
interesting work here.
- New subdriver for Renesas R-Car r8a7745 (RZ/G1E).
Misc:
- Several fixes and improvements for Xilinx Zynq GPIO.
- Support an enablement GPIO for the 74x164 GPIO.
- Switch a bunch of chips to use devres to allocate irq descriptors.
- A bunch of constification fixes"
* tag 'gpio-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (63 commits)
gpio: mockup: remove unused variable gc
gpio: pl061: constify amba_id
Revert "gpiolib: request the gpio before querying its direction"
gpio: twl6040: remove unneeded forward declaration
gpio: zevio: make gpio_chip const
gpio: add gpio_add_lookup_tables() to add several tables at once
gpio: rcar: Add r8a7745 (RZ/G1E) support
gpio: brcmstb: check return value of gpiochip_irqchip_add()
MAINTAINERS: Add entry for THUNDERX GPIO Driver.
gpio: Add gpio driver support for ThunderX and OCTEON-TX
gpio: mockup: use irq_sim
gpio: mxs: use devres for irq generic chip
gpio: mxc: use devres for irq generic chip
gpio: pch: use devres for irq generic chip
gpio: ml-ioh: use devres for irq generic chip
gpio: sta2x11: use devres for irq generic chip
gpio: sta2x11: disallow unbinding the driver
gpio: mxs: disallow unbinding the driver
gpio: mxc: disallow unbinding the driver
gpio: aspeed: Remove reference to clock name in debounce warning message
...
This adds a section about the various parts of the GPIO subsystem to the
driver API documentation. Note that this isn't exhaustive documentation,
but rather focusses on pulling in the kerneldoc from various sources, in
order to improve coverage of kerneldoc processing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
There's no use for this blank line at the end of the file. Remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The only function of interest in that file was scsi_print_status(). That
function was removed in commit 7ac7076344 (scsi: remove
scsi_print_status()) but the docs were not changed to match, yielding this
warning:
./drivers/scsi/constants.c:1: warning: no structured comments found
There's nothing there anymore, so just remove that section from the docs.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Back in 2012, commit 9807f75955 (UAPI: (Scripted) Disintegrate
arch/s390/include/asm) moved struct cmbdata (and its kerneldoc comments) to
another file, but did not update the docs to match. The result is this
warning:
./arch/s390/include/asm/cmb.h:1: warning: no structured comments found
...and no documentation for that structure. Update the docs to get the
information from the right place.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are no kerneldoc comments in drivers/dma-buf/seqno-fence.c, and it
appears there never have been. Stop looking for comments there to
eliminate this warning:
./drivers/dma-buf/seqno-fence.c:1: warning: no structured comments found
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
...because there are none there, and I cannot figure out what would ever
have been of interest there. This eliminates this warning:
./kernel/sys.c:1: warning: no structured comments found
from the build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The docs build complains:
./include/linux/init.h:1: warning: no structured comments found
The problem is that the comments in question were moved to module.h in
commit 0fd972a7d9 (module: relocate module_init from init.h to
module.h). Fix basics.rst to match.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
removal of kernel/rcu/srcu.c. Also correct a stray pointer in
memory-barriers.txt.
-----BEGIN PGP SIGNATURE-----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=JEoA
-----END PGP SIGNATURE-----
Merge tag '4.13-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A set of fixes for various warnings, including the one caused by the
removal of kernel/rcu/srcu.c. Also correct a stray pointer in
memory-barriers.txt"
* tag '4.13-fixes' of git://git.lwn.net/linux:
kokr/memory-barriers.txt: Fix obsolete link to atomic_ops.txt
memory-barriers.txt: Fix broken link to atomic_ops.txt
docs: Turn off section numbering for the input docs
docs: Include uaccess docs from the right file
docs: Do not include from kernel/rcu/srcu.c
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
That file went away with commit bd8cc5a062 (srcu: Remove Classic SRCU)
during the 4.13 merge window, leading to errors like:
Error: Cannot open file ./kernel/rcu/srcu.c
during the docs build.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
As pinctrl describes a feature from drivers/base, place it at
the right book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----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=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
a) Linux can be an I2C slave meanwhile
b) all drivers except one use the driver model currently
Update the documentation.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The firmware API should not be used after we go to suspend
and after we reboot/halt. The suspend/resume case is a bit
complex, so this documents that so things are clearer.
We want to know about users of the API in incorrect places so
that their callers are corrected, so this also adds a warn
for those cases.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out the exported SMBus functions and the emulation layer into a
separate file. This also involved splitting up the tracing header into
an I2C and an SMBus part.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core became quite huge and its monolithic structure makes
maintenance hard. So, prepare to break out some functionality into
separate files by renaming the source file. Note that we keep the
resulting object name constant to avoid regressions.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Group the :: with the previous paragraph, in order to make it
visually better when reading as a text file.
While here, replace:
ored (with means "Covered or adorned with ore or metal")
by:
OR-ed
To reflect its true meaning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
The tables were manually adjusted to fit into 80 columns.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of just using text for functions and structs, use
the C domain tags, in order to allow cross-referencing with
the kernel-doc markups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use pandoc to convert documentation to ReST by calling
Documentation/sphinx/tmplcvt script.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
The contents of proc_usb_info.txt complements what's there at
driver-api usb book. Yet, it is outdated, as it still refers
to the USB character devices as usbfs.
So, move the contents to usb.rst, adjusting it to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's no usbfs anymore. The old features are now either
exported to /dev/bus/usb or via debugfs.
Update documentation accordingly, pointing to the new
places where the character devices and usb/devices are
now placed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As some USB documentation files got moved, adjust their
cross-references to their new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The URB doc describes the Kernel mechanism that do USB transfers.
While the functions are already described at urb.h, there are a
number of concepts and theory that are important for USB driver
developers.
Convert it to ReST and use C ref links to point to the places
at usb.h where each function and struct is located.
A few of those descriptions were incomplete. While here, update
to reflect the current API status.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core features. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core features. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core features. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core features. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core functions. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core functions. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core functions. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document describe some USB core functions. Add it to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This file is actually quite complex, and required several
manual handwork:
- add a title for the document;
- use the right tags for monospaced fonts;
- use c references where needed;
- adjust cross-reference to writing_usb_driver.rst
- hightlight cross-referenced lines.
With regards to C code snippet line highlights, the better would be
to use :linenos: for the C code snippets that are referenced by
the line number. However, at least with Sphinx 1.4.9, enabling
it cause the line number to be misaligned with the code,
making it even more confusing. So, instead, let's use
:emphasize-lines: tag to mark the lines that are referenced
at the text.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The pandoc conversion is not perfect. Do handwork in order to:
- add a title to this chapter;
- adjust function and struct references;
- use monospaced fonts for C code names;
- some other minor adjustments to make it better to read in
text mode and in html.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The pandoc conversion is not perfect. Do handwork in order to:
- add a title to this chapter;
- use the proper warning and note markups;
- use kernel-doc to include Kernel header and c files;
- remove legacy notes with regards to DocBook;
- some other minor adjustments to make it better to read in
text mode and in html.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- use the proper warning and note markups;
- add references for parts of the document that will be
cross-referenced on other USB docs;
- some minor adjustments to make it better to read in
text mode and in html.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As we're moving out of DocBook, let's convert the remaining
USB docbooks to ReST.
The transformation itself on this patch is a no-brainer
conversion using pandoc via this script:
Documentation/sphinx/tmplcvt
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The structs there at device table are used by other documentation
at the Kernel. So, add it to the driver API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are several stuff there that are actually driver-specific.
Move those to the driver_api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This introduction section should be used in the documentation,
do that at the beginning of the cfg80211 chapter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the connect event from driver takes all the connection
response parameters as arguments. With support for new features these
response parameters can grow. Use a structure to pass these parameters
rather than passing them as function arguments.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add to documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update VME documentation given that kerneldoc comments are now provided.
Add "VME API" section to VME RST to pull in kerneldoc comments.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Three more DocBook template files have been converted to RST; only 21 to
go. There are various build improvements and the usual array of
documentation improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=C5nd
-----END PGP SIGNATURE-----
Merge tag 'docs-4.11' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A slightly quieter cycle for documentation this time around.
Three more DocBook template files have been converted to RST; only 21
to go. There are various build improvements and the usual array of
documentation improvements and fixes"
* tag 'docs-4.11' of git://git.lwn.net/linux: (44 commits)
docs / driver-api: Fix structure references in device_link.rst
PM / docs: Fix structure references in device.rst
Add a target to check broken external links in the Documentation
Documentation: Fix linux-api list typo
Documentation: DocBook/Makefile comment typo
Improve sparse documentation
Documentation: make Makefile.sphinx no-ops quieter
Documentation: DMA-ISA-LPC.txt
Documentation: input: fix path to input code definitions
docs: Remove the copyright year from conf.py
docs: Fix a warning in the Korean HOWTO.rst translation
PM / sleep / docs: Convert PM notifiers document to reST
PM / core / docs: Convert sleep states API document to reST
PM / core: Update kerneldoc comments in pm.h
doc-rst: Fix recursive make invocation from macros
doc-rst: Delete output of failed dot-SVG conversion
doc-rst: Break shell command sequences on failure
Documentation/sphinx: make targets independent of Sphinx work for HAVE_SPHINX=0
doc-rst: fixed cleandoc target when used with O=dir
Documentation/sphinx: prevent generation of .pyc files in the source tree
...
Here is the "small" driver core patches for 4.11-rc1.
Not much here, some firmware documentation and self-test updates, a
debugfs code formatting issue, and a new feature for call_usermodehelper
to make it more robust on systems that want to lock it down in a more
secure way.
All of these have been linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2jKg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymCEACgozYuqZZ/TUGW0P3xVNi7fbfUWCEAn3nYExrc
XgevqeYOSKp2We6X/2JX
=aZ+5
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "small" driver core patches for 4.11-rc1.
Not much here, some firmware documentation and self-test updates, a
debugfs code formatting issue, and a new feature for call_usermodehelper
to make it more robust on systems that want to lock it down in a more
secure way.
All of these have been linux-next for a while now with no reported
issues"
* tag 'driver-core-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: handle null pointers while printing node name and path
Introduce STATIC_USERMODEHELPER to mediate call_usermodehelper()
Make static usermode helper binaries constant
kmod: make usermodehelper path a const string
firmware: revamp firmware documentation
selftests: firmware: send expected errors to /dev/null
selftests: firmware: only modprobe if driver is missing
platform: Print the resource range if device failed to claim
kref: prefer atomic_inc_not_zero to atomic_add_unless
debugfs: improve formatting of debugfs_real_fops()
Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here. Rework for the hyperv
subsystem to handle new platforms better, mei and w1 and extcon driver
updates, as well as a number of other "minor" driver updates. Full
details are in the shortlog below.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2iRQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynhFACguVE+/ixj5u5bT5DXQaZNai/6zIAAmgMWwd/t
YTD2cwsJsGbTT1fY3SUe
=CiSI
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here: rework for the
hyperv subsystem to handle new platforms better, mei and w1 and extcon
driver updates, as well as a number of other "minor" driver updates.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
goldfish: Sanitize the broken interrupt handler
x86/platform/goldfish: Prevent unconditional loading
vmbus: replace modulus operation with subtraction
vmbus: constify parameters where possible
vmbus: expose hv_begin/end_read
vmbus: remove conditional locking of vmbus_write
vmbus: add direct isr callback mode
vmbus: change to per channel tasklet
vmbus: put related per-cpu variable together
vmbus: callback is in softirq not workqueue
binder: Add support for file-descriptor arrays
binder: Add support for scatter-gather
binder: Add extra size to allocator
binder: Refactor binder_transact()
binder: Support multiple /dev instances
binder: Deal with contexts in debugfs
binder: Support multiple context managers
binder: Split flat_binder_object
auxdisplay: ht16k33: remove private workqueue
auxdisplay: ht16k33: rework input device initialization
...
The format of the structure references in device_link.rst is
incorrect, because it doesn't cause proper references to the
struct data types to be generated (for struct dev_pm_domain in
particular).
Fix that by using the :c:type:`struct name <name>` convention
for encoding references to struct data types.
Fixes: aad800403a (Documentation/core-api/device_link: Add initial documentation)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There is a better way to represent structure references than it was
done in device.rst by commit 730c4c0530 (PM / sleep / docs: Convert
PM notifiers document to reST), which is to use "struct name" as a
link caption (e.g. :c:type:`struct device <device>`). That will
cause sphinx to generate a proper reference to the data type in
question (struct device in the example above) and "struct name"
will work as the link in the HTML output.
Fix device.rst by using that convention where applicable.
Fixes: 730c4c0530 (PM / sleep / docs: Convert PM notifiers document to reST)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Move the document describing PM notifiers (used during system sleep
state transitions) to Documentation/driver-api/pm/, convert it to reST
and update it to use current terminology. Also replace the remaining
references to the old version of it in .txt documents with references
to the new one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Move the document describing the system sleep state transitions API
for devices to Documentation/driver-api/pm/, convert it to reST and
update it to use current terminology. Also remove the remaining
reference to the old version of it from pm.h.
The new document still contains references to some documents in the
.txt format that will be converted later.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A fairly straightforward conversion to RST; the document is then added to
the driver-api manual.
Of course, this document has seen no substantive changes since 2008, so
chances are it needs work in other areas as well.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert deviceiobook.tmpl to RST and incorporate it into the driver API
manual.
Like the rest of our documentation, this one could use some work. There's
no mention of ioremap() and friends, no mention of io_read*() and friends.
But we have nice documentation for all those folks writing new drivers that
do port I/O :).
The :c:func: notation has been left off of all the read*/write* functions.
There's no kerneldoc comments for them anyway, so those links will never be
live, and writing a bunch of repetitive "read a byte from I/O memory"
comments lacks appeal.
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Understanding this code is getting out of control without any
notes. Give the firmware_class driver a much needed documentation love,
and while at it convert it to the new sphinx documentation format.
v2: typos and small fixes
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
This is a manual conversion of the existing DocBook documentation
for IIO. The intent is not to substantially change any of the
content in this patch, but to give a base to build upon.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The references to drivers/base/power/main.c and
drivers/acpi/scan.c from Documentation/driver-api/infrastructure.rst
are confusing. They both cause descriptions of functions that are
not relevant to device drivers at all to be generated and none of
them is sufficient to cover the API in a meaningful way.
Drop them for now.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Instead of storing the concepts dictionary inside header file,
move it to the subsystem documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, there's no device driver documentation for the EDAC
subsystem at the driver-api book. Fill in the blanks for the
structures and functions that misses documentation, uniform
the word on the existing ones, and add a new edac.rst file at
driver-api, in order to document the EDAC subsystem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Put all the remaing bits of the old doc into suitable places in the
new sphinx world.
- Also document the poll support, we forgot to do that.
- Delete dma-buf-sharing.txt.
v2: Don't forget to update MAINTAINERS.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161209215055.3492-1-daniel.vetter@ffwll.ch
- Again move the information relevant for driver writers next to the
callbacks.
- Put the overview and userspace interface documentation into a DOC:
section within the code.
- Remove the text that mmap needs to be coherent - since the
DMA_BUF_IOCTL_SYNC landed that's no longer the case. But keep the text
that for pte zapping exporters need to adjust the address space.
- Add a FIXME that kmap and the new begin/end stuff used by the SYNC
ioctl don't really mix correctly. That's something I just realized
while doing this doc rework.
- Augment function and structure docs like usual.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
[sumits: fix cosmetic issues]
Link: http://patchwork.freedesktop.org/patch/msgid/20161209185309.1682-5-daniel.vetter@ffwll.ch
- Put the initial overview for dma-buf into dma-buf.rst.
- Put all the comments about detailed semantics into the right
kernel-doc comment for functions or ops structure member.
- To allow that detail, switch the reworked kerneldoc to inline style
for dma_buf_ops.
- Tie everything together into a much more streamlined overview
comment, relying on the hyperlinks for all the details.
- Also sprinkle some links into the kerneldoc for dma_buf and
dma_buf_attachment to tie it all together.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161209185309.1682-4-daniel.vetter@ffwll.ch
Just prep work to polish and consolidate all the dma-buf related
documenation.
Unfortunately I didn't discover a way to both integrate this new file
into the overall toc while keeping it at the current place. Work
around that by moving it into the overall driver-api/index.rst.
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Document device links as introduced in v4.10 with commits:
4bdb35506b ("driver core: Add a wrapper around
__device_release_driver()")
9ed9895370 ("driver core: Functional dependencies tracking
support")
8c73b42884 ("PM / sleep: Make async suspend/resume of devices use
device links")
21d5c57b37 ("PM / runtime: Use device links")
baa8809f60 ("PM / runtime: Optimize the use of device links")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[ jc: Moved from core-api to driver-api ]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Put this documentation with the other driver docs and try to keep the top
level reasonably clean.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a conversion of the USB documentation to the Sphinx format.
No content was altered or reformatted.
Signed-off-by: Oliver <oneukum@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Few files under dma-buf/ changed their names but the changes didn't
applied to a document that referencing them. It is causing few
documentation build warnings. This commit fixes the problems by
applying changed file names on the document.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add minimal conf.py makes the driver-api folder buildable
stand-alone. To build only this folder run::
make SPHINXDIRS=driver-api htmldocs
make SPHINXDIRS=driver-api pdfdocs
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Perform a relatively simple conversion of vme_api.txt to reStructuredText
and move under driver-api, which seems the most logical place for this
documentation.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It never made sense to keep these documents together; move each into its
own file.
Drop the section numbering on hsi.txt on its way to its own file.
Suggested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The HSI subsystem documentation was split across hsi.txt and the
device-drivers docbook. Now that the latter has been converted to Sphinx,
pull in the HSI document so that it's all in one place.
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We don't need to keep it as a single large file anymore; split it up so
that it is easier to manage and the individual sections can be read
directly as plain files.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Linus Walleij