If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
This triggers lots of messages like:
irq 117, desc: ffff88017a61e600, depth: 1, count: 0, unhandled: 0
->handle_irq(): ffffffff8109b613, handle_bad_irq+0x0/0x1e0
->irq_data.chip(): ffffffffa0020180, chv_pinctrl_exit+0x2d84/0x12 [pinctrl_cherryview]
->action(): (null)
IRQ_NOPROBE set
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Cc: stable@vger.kernel.org
Reported-by: Christian Steiner <christian.steiner@outlook.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group index is incremented on every new group parsed. Since the
field is part of struct imx_pinctrl_soc_info, which is typically
a global variable passed by the individual pinctrl-imx.c based
driver, it does not get cleared automatically when re-probing the
driver. This lead imx_pinctrl_parse_functions passing a group
pointer which is outside of the allocated group space on second
probe and onwards. Typically this ended up in a NULL pointer
dereference when accessing the name field like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at strcmp+0x18/0x44
LR is at imx_dt_node_to_map+0xc4/0x290
Avoid this by setting group_index to 0 on probe.
This has been observed when using DEBUG_TEST_DRIVER_REMOVE.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to probe stm32 pinctrl driver even if no interrupt
controller is defined to manage gpio irqs.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Thanks to 332e99d5ae which now alerts of default
trigger usage when configuring interrupts.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 44a7185c2a ("of/platform: Add common method to populate
default bus"), ARM64 platform devices are populated at the
arch_initcall_sync level; as a result, the platform_driver_probe calls
in both the iProc and NSP GPIO drivers fail with -ENODEV since by that
time the platform device was not yet registered.
Replace platform_driver_probe with platform_driver_register, that allow
the device to be register later
Fixes: 44a7185c2a ("of/platform: Add common method to populate default bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dell XPS 13 (and maybe some others) uses a GPIO (CPU_GP_1) during suspend
to explicitly disable USB touchscreen interrupt. This is done to prevent
situation where the lid is closed the touchscreen is left functional.
The pinctrl driver (wrongly) assumes it owns all pins which are owned by
host and not locked down. It is perfectly fine for BIOS to use those pins
as it is also considered as host in this context.
What happens is that when the lid of Dell XPS 13 is closed, the BIOS
configures CPU_GP_1 low disabling the touchscreen interrupt. During resume
we restore all host owned pins to the known state which includes CPU_GP_1
and this overwrites what the BIOS has programmed there causing the
touchscreen to fail as no interrupts are reaching the CPU anymore.
Fix this by restoring only those pins we know are explicitly requested by
the kernel one way or other.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=176361
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initialize the spinlock before using it.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.8.0-dwc-bisect #4
Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8_X64_R_2014_13_1_00 03/24/2014
0000000000000000 ffff8800788ff770 ffffffff8133d597 0000000000000000
0000000000000000 ffff8800788ff7e0 ffffffff810cfb9e 0000000000000002
ffff8800788ff7d0 ffffffff8205b600 0000000000000002 ffff8800788ff7f0
Call Trace:
[<ffffffff8133d597>] dump_stack+0x67/0x90
[<ffffffff810cfb9e>] register_lock_class+0x52e/0x540
[<ffffffff810d2081>] __lock_acquire+0x81/0x16b0
[<ffffffff810cede1>] ? save_trace+0x41/0xd0
[<ffffffff810d33b2>] ? __lock_acquire+0x13b2/0x16b0
[<ffffffff810cf05a>] ? __lock_is_held+0x4a/0x70
[<ffffffff810d3b1a>] lock_acquire+0xba/0x220
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff81631567>] _raw_spin_lock_irqsave+0x47/0x60
[<ffffffff8136f1fe>] ? byt_gpio_get_direction+0x3e/0x80
[<ffffffff8136f1fe>] byt_gpio_get_direction+0x3e/0x80
[<ffffffff813740a9>] gpiochip_add_data+0x319/0x7d0
[<ffffffff81631723>] ? _raw_spin_unlock_irqrestore+0x43/0x70
[<ffffffff8136fe3b>] byt_pinctrl_probe+0x2fb/0x620
[<ffffffff8142fb0c>] platform_drv_probe+0x3c/0xa0
...
Based on the diff it looks like the problem was introduced in
commit 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
but I wasn't able to verify that empirically as the parent commit
just oopsed when I tried to boot it.
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: stable@vger.kernel.org
Fixes: 71e6ca61e8 ("pinctrl: baytrail: Register pin control handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prevented C20 from successfully being muxed as GPIO.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes simple typos in the initial commit. There is no behavioural
change.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Xo Wang <xow@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consider a scenario with one pin P that has two signals A and B, where A
is defined to be higher priority than B: That is, if the mux IP is in a
state that would consider both A and B to be active on P, then A will be
the active signal.
To instead configure B as the active signal we must configure the mux so
that A is inactive. The mux state for signals can be described by
logical operations on one or more bits from one or more registers (a
"signal expression"), which in some cases leads to aliased mux states for
a particular signal. Further, signals described by multi-bit bitfields
often do not only need to record the states that would make them active
(the "enable" expressions), but also the states that makes them inactive
(the "disable" expressions). All of this combined leads to four possible
states for a signal:
1. A signal is active with respect to an "enable" expression
2. A signal is not active with respect to an "enable" expression
3. A signal is inactive with respect to a "disable" expression
4. A signal is not inactive with respect to a "disable" expression
In the case of P, if we are looking to activate B without explicitly
having configured A it's enough to consider A inactive if all of A's
"enable" signal expressions evaluate to "not active". If any evaluate to
"active" then the corresponding "disable" states must be applied so it
becomes inactive.
For example, on the AST2400 the pins composing GPIO bank H provide
signals ROMD8 through ROMD15 (high priority) and those for UART6 (low
priority). The mux states for ROMD8 through ROMD15 are aliased, i.e.
there are two mux states that result in the respective signals being
configured:
A. SCU90[6]=1
B. Strap[4,1:0]=100
Further, the second mux state is a 3-bit bitfield that explicitly
defines the enabled state but the disabled state is implicit, i.e. if
Strap[4,1:0] is not exactly "100" then ROMD8 through ROMD15 are not
considered active. This requires the mux function evaluation logic to
use approach 2. above, however the existing code was using approach 3.
The problem was brought to light on the Palmetto machines where the
strap register value is 0x120ce416, and prevented GPIO requests in bank
H from succeeding despite the hardware being in a position to allow
them.
Fixes: 318398c09a8d ("pinctrl: Add core pinctrl support for Aspeed SoCs")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
The following commit introduced a regression by not properly masking the
calculated value.
Fixes: 47a01ee9a6 ("pinctrl: qcom: Clear all function selection bits")
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some Intel BXT platform, wake-up from suspend-to-idle on pressing
power-button is not working. Its noticed that gpio-keys driver marking the
second level IRQ/power-button as wake capable but Intel pintctrl
driver is missing to mark GPIO chip/controller IRQ which first level IRQ
as wake cable if its GPIO pin IRQ is wakeble. So, though the first level
IRQ gets generated on power-button press, since it is not marked as
wake capable resume/wake-up flow is not happening.
Intel pintctrl/GPIO driver need to mark GPIO chip/controller IRQ (first
level IRQ) as wake capable iff GPIO pin's IRQ (second level IRQ) is marked
as wake cable.
Changes in v2:
- Add missing irq initialisation.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies the error handling and allows us to drop the whole
chv_pinctrl_remove() function.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that for north and southwest communities, they can only
generate GPIO interrupts for lower 8 interrupts (IntSel value). The upper
part (8-15) can only generate GPEs (General Purpose Events).
Now the reason why EC events such as pressing hotkeys does not work if we
mask all the interrupts is that in order to generate either interrupts or
GPEs the INTMASK register must have that particular interrupt unmasked. In
case of GPEs the CPU does not trigger normal interrupt (and thus the GPIO
driver does not see it) but instead it causes SCI (System Control
Interrupt) to be triggered with the GPE in question set.
To make this all work as expected we only add those GPIOs to the IRQ domain
that can actually generate interrupts (IntSel value 0-7) and skip others.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfiWTAACgkQCwYYjhRyO9X3ZQCfdOuvxXIajKkmxgvVwNgzEeLF
GEIAn1LYY/vmNikPhxH4O2FBi/9NBdZM
=GrPA
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu into next/drivers
Pull "mvebu drivers for 4.9 (part 1)" from Gregory CLEMENT:
- Add pinctrl and clk support for the Orion5x SoC mv88f5181 variant
* tag 'mvebu-drivers-4.9-1' of git://git.infradead.org/linux-mvebu:
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
As far as I'm aware the mv88f5181-b1 and mv88f5181l are the same at the
pinctrl level, so re-use the definitions for both.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
There is no point in adding any default trigger for these
GPIO interrupts: the device tree should contain all trigger
information and the platforms using the driver boots
exclusively from device tree.
Also the boot log is nagging me to fix this:
[ 0.771057] ------------[ cut here ]------------
[ 0.775695] WARNING: CPU: 0 PID: 1 at
../drivers/gpio/gpiolib.c:1622 _gpiochip_irqchip_add+0x138/0x160
[ 0.785034] /soc/gpio@8012e000: Ignoring 2 default trigger
(...)
[ 0.942962] gpio 8012e000.gpio: at address e08f8000
(etc ad nauseam)
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the ST pinctrl driver and removes
references to these obsolete platforms. As some structures
referenced by STiH407 based configuration were shared with
STiH416 we update these names to match the remaining
supported platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linus.walleij@linaro.org>
Cc: <linux-gpio@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EE domains pins for the NAND flash controller.
Even tough we have no driver for the NAND flash controller yet, we need
to have these pins in pinctrl as the actual pin are shared with the spifc
controller. The bootloader on the S905-P200 setup pinmux for the NAND
controller so we need the kernel to properly deactivate this if necessary.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:
drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)
This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0eb9f68333 ("pinctrl: Add IRQ support to STM32 gpios")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=APGj
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.9-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9 (take three)
- Return pinconf with arguments in packed format,
- MSIOF and QSPI pin groups on R-Car V2H,
- Voltage switching for SDHI on R-Car M2-W, E2, and M3-W.
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All the SHDIs can operate with either 3.3V or 1.8V signals, depending
on negotiation with the card.
Based on work by Wolfram Sang for the r8a7790.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This follows the style of existing PORT_GP_X macros and
will be used by a follow-up patch for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This adds the SDIO interrupt pin which can be used by sd_emmc_a.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 29885a6565 ("pinctrl: meson-gxbb: add the pins for the
SDIO/sd_emmc_a controller")
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added aspeed driver tries to check for a negative return
value from a pinctrl function, but stores the intermediate value in
a 'bool' variable, which cannot work:
drivers/pinctrl/aspeed/pinctrl-aspeed.c: In function 'aspeed_sig_expr_set':
drivers/pinctrl/aspeed/pinctrl-aspeed.c:192:11: error: comparison of constant '0' with boolean expression is always false [-Werror=bool-compare]
This slightly reworks the logic to use an explicit comparison with zero
before assigning to the temporary variable.
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The earlier patch can be simplified by using a bool
to indicate level trigger.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
[Fixup to earlier manually applied patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds IRQ support to STM32 gpios.
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
samsung_pinctrl_probe() can be called only after matching
the driver by the compatible string so this already implies
a non null dev->of_node. Remove the always false test
and related error trace. While at it drop another error log
in case of memory allocation failure - any errors are logged
by the memory subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In function mrfld_pinctrl_probe(), when duplicating the mrfld_families
array the requested memory region length is multiplied once too many by the
number of elements in the original array. Fix this to spare some memory.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
at91 used to set a default trigger type for GPIO interrupts in
order to cope with the old board files. These days are long gone,
and it all gets probed through DT.
Andras Szemzo reported that the Ethernet device on his board was
bailing to be probed, due to a conflict in interrupt trigger.
Surely enough, this is due to this default trigger still being
present, and turning this into a IRQ_TYPE_NONE fixes the issue.
Reported-by: Andras Szemzo <szemzo.andras@gmail.com>
Tested-by: Andras Szemzo <szemzo.andras@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the {get,set}_io_voltage operations of SDHI.
This operates the POCCTRL0 register on R8A7796 SoC and makes 1.8v/3.3v
voltage switch.
Based on work by Takeshi Kihara and Wolfram Sang.
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinconf-generic code expects configurations with arguments to be
returned in a packed format in order to be displayed properly by
pinconf_generic_dump_one().
Reading /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins on
r8a7795/salvator-x now shows:
pin 101 (GP_3_5): output drive strength (9 mA), pin power source (3300 selector)
Instead of:
pin 101 (GP_3_5): output drive strength (0 mA), pin power source (0 selector)
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add MSIOF0/1 pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add QSPI pin groups to the R8A7792 PFC driver.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
H3 has single PWM channel. The second PWM channel is not supported,
so the pinctrl function should be removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew Jeffery