Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises the new HW flag USE_RSS, make the
station statistics on the fast-rx path per-CPU. This will
enable calling the RX in parallel, only hitting locking or
shared cachelines when the fast-RX path isn't available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 32-bit platforms, the 64-bit counters we keep need to be protected
to be consistently read. Use the u64_stats_sync mechanism to do that.
In order to not end up with overly long lines, refactor the tidstats
assignments a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When storing the last_rate_* values in the RX code, there's nothing
to guarantee consistency, so a concurrent reader could see, e.g.
last_rate_idx on the new value, but last_rate_flag still on the old,
getting completely bogus values in the end.
To fix this, I lifted the sta_stats_encode_rate() function from my
old rate statistics code, which encodes the entire rate data into a
single 16-bit value, avoiding the consistency issue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the averaged values out of rx_stats and into rx_stats_avg,
to cleanly split them out. The averaged ones cannot be supported
for parallel RX in a per-CPU fashion, while the other values can
be collected per CPU and then combined/selected when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the semicolon, people typically assume that and
once line already put a semicolon behind the "call".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the RX MSDU statistics, we need to count the number of
MSDUs created and accepted from an A-MSDU. Right now, all
frames in any A-MSDUs were completely ignored. Fix this by
moving the RX MSDU statistics accounting into the deliver
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code is only used with iwlwifi, but still should have proper
mac80211 naming scheme; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device implements dynamic PS itself, there's no need
to ever start the dynamic powersave timer on RX.
While at it, fix up some indentation in this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e173245 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e173245 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remember the last time when a mpp table entry is used for
rx or tx and remove them after MESH_PATH_EXPIRE time.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepararation for zero-copy A-MSDU support with page fragment SKBs
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If any frames are dropped that are part of a BA session, the reorder
buffer will "indefinitely" (until the timeout) wait for them to come
in (or a BAR moving the window) and won't release frames after them.
This means it isn't possible to filter frames within a BA session in
firmware.
Introduce an API function that allows such filtering. Calling this
function will move the BA window forward to the new SSN, and allows
marking frames after the SSN as having been filtered, so any future
reordering activity will release frames while skipping the holes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up ieee80211_rx_reorder_ready() callers by passing the RX
TID struct and the index, instead of the frames list. This will
make it more extensible as well.
While at it, move the inline to rx.c as it's only used there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers offload some frames internally (e.g.
AddBa). Reporting such frames to mac80211 would
only confuse MLME. However it would be useful to
be able to pass such frames to monitor interfaces
for sniffing purposes, e.g. when running AP +
monitor.
To do that allow drivers to tell mac80211 whether
a given frame should be:
- processed but not delivered to any monitor vif
- not processed but delievered to monitor vifs
only
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option for driver to check for packet duplication
by itself.
This is needed for example by the iwlwifi driver which
parallelizes the RX path and does the duplication check
per queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really should never happen except very early in the process
of bringing up a new driver, at which point you'll have to add
more debugging in the driver and this string isn't useful. Remove
it and save some size (when it's even compiled in.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.
This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a long-standing TODO item to use this flag in the cooked
monitor RX, but clearly it was never needed and now this hasn't
been used by userspace for a long time, so no userspace changes
could require it now.
Remove the unused flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This counter is inherently racy (since it can be incremented by RX
as well as by concurrent TX) and only available in debugfs. Instead
of fixing it to be per-CPU or similar, remove it for now. If needed
it should be added without races and with proper nl80211, perhaps
even addressing the threshold reporting TODO item that's been there
since the code was originally added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As there's no driver using this capability and reporting zero-length
A-MPDU subframes for radiotap monitoring, remove the capability to
free up two RX flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is only used in the RX code, so moving it into
that file gives the compiler better optimisation possibilities
and also allows us to remove the check for short frames (which
in the RX path cannot happen, but as a generic utility needed
to be checked.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Short frames less than 16 octets are already blocked in the monitor
code by the should_drop_frame() function, and cannot get into the
regular RX path. Therefore, this check can never trigger and the
counter invariably stays zero. Remove the useless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We typically use 'sta' for the station info struct, and if needed
'pubsta' for the public (driver-visible) portion thereof. Do this
in the ieee80211_sta_ps_transition() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter how the driver manages its NAPI context, there's no way
sending frames to it from a timer can be correct, since it would
corrupt the internal GRO lists.
To avoid that, always use the non-NAPI path when releasing frames
from the timer.
Cc: stable@vger.kernel.org
Reported-by: Jean Trivelly <jean.trivelly@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since these counters can only be read through debugfs, there's
very little point in maintaining them all the time. However,
even just making them depend on debugfs is pointless - they're
not normally used. Additionally a number of them aren't even
concurrency safe.
Move them under MAC80211_DEBUG_COUNTERS so they're normally
not even compiled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs statistics macros are pointlessly verbose, so change
that macro to just have a single argument. While at it, remove
the unused counters and rename rx_expand_skb_head2 to the better
rx_expand_skb_head_defrag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When frames time out in the reordering buffer, it is a
good indication that something went wrong and the driver
may want to know about that to take action or trigger
debug flows.
It is pointless to notify the driver about each frame that
is released. Notify each time the timer fires.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we receive a BAR, this typically means that our peer
doesn't hear our Block-Acks or that we can't hear its
frames. Either way, it is a good indication that the link
is in a bad condition. This is why it can serve as a probe
to the driver.
Use the event_callback callback for this.
Since more events with the same data will be added in the
feature, the structure that describes the data attached to
the event is called in a generic name: ieee80211_ba_event.
This also means that from now on, the event_callback can't
sleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't all that relevant for RX right now, but TX can be concurrent
due to multi-queue and the accounting is therefore broken.
Use the standard per-CPU statistics to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The OCB input path already checked that the BSSID is the broadcast
address, so the later check can never fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Masashi Honma