With the help of boolinit.cocci, we use !nl80211_reg_change_event_fill
instead of (nl80211_reg_change_event_fill == false). Meanwhile, Clean
up the code.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Link: https://lore.kernel.org/r/1567657537-65472-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we expire an inactive station, try to send it a deauth. This
helps if it's actually still around, and just has issues with
beacon distribution (or we do), and it will not also remove us.
Then, if we have shared state, this may not be reset properly,
causing problems; for example, we saw a case where aggregation
sessions weren't removed properly (due to the TX start being
offloaded to firmware and it relying on deauth for stop), causing
a lot of traffic to get lost due to the SN reset after remove/add
of the peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-9-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already assume that key is not NULL and dereference it in a few
other places before we check whether it is NULL, so the check is
unnecessary. Remove it.
Fixes: 96fc6efb9a ("mac80211: IEEE 802.11 Extended Key ID support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-8-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we got a fw restart while roaming from encrypted AP to
non-encrypted one, we might end up with hitting a warning on the pending
counter crypto_tx_tailroom_pending_dec having a non-zero value.
The following comment taken from net/mac80211/key.c explains the rational
for the delayed tailroom needed:
/*
* The reason for the delayed tailroom needed decrementing is to
* make roaming faster: during roaming, all keys are first deleted
* and then new keys are installed. The first new key causes the
* crypto_tx_tailroom_needed_cnt to go from 0 to 1, which invokes
* the cost of synchronize_net() (which can be slow). Avoid this
* by deferring the crypto_tx_tailroom_needed_cnt decrementing on
* key removal for a while, so if we roam the value is larger than
* zero and no 0->1 transition happens.
*
* The cost is that if the AP switching was from an AP with keys
* to one without, we still allocate tailroom while it would no
* longer be needed. However, in the typical (fast) roaming case
* within an ESS this usually won't happen.
*/
The next flow lead to the warning eventually reported as a bug:
1. Disconnect from encrypted AP
2. Set crypto_tx_tailroom_pending_dec = 1 for the key
3. Schedule work
4. Reconnect to non-encrypted AP
5. Add a new key, setting the tailroom counter = 1
6. Got FW restart while pending counter is set ---> hit the warning
While on it, the ieee80211_reset_crypto_tx_tailroom() func was merged into
its single caller ieee80211_reenable_keys (previously called
ieee80211_enable_keys). Also, we reset the crypto_tx_tailroom_pending_dec
and remove the counters warning as we just reset both.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-7-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we reach this point, the key cannot be NULL. Remove the condition
that suggests otherwise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-6-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
"HE/HT/VHT" is a bit confusing since really the order of
development (and possible support) is different - change
this to "HT/VHT/HE".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-4-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the RFKILL subsystem isn't available, then rfkill_blocked()
always returns false. In the case of hardware rfkill this will
be wrong though, as if the hardware reported being killed then
it cannot operate any longer.
Since we only ever call the rfkill_sync work in this case, just
rename it to rfkill_block and always pass "true" for the blocked
parameter, rather than passing rfkill_blocked().
We rely on the underlying driver to still reject any new attempt
to bring up the device by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes was missed in parsing the vht capabilities max bw
support.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: e80d642552 ("mac80211: copy VHT EXT NSS BW Support/Capable data to station")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830114057.22197-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The boundary value used for the 6G band was incorrect as it would
result in invalid 6G channel number for certain frequencies.
Reported-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1567510772-24263-1-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for packet mirroring and redirection. The
nft_fwd_dup_netdev_offload() function configures the flow_action object
for the fwd and the dup actions.
Extend nft_flow_rule_destroy() to release the net_device object when the
flow_rule object is released, since nft_fwd_dup_netdev_offload() bumps
the net_device reference counter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
Register a new synproxy stateful object type into the stateful object
infrastructure.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This issue causes SCTP_PEER_ADDR_THLDS sockopt not to be able to dump
a transport thresholds info.
Fix it by adding 'goto' put_user in sctp_getsockopt_paddr_thresholds.
Fixes: 8add543e36 ("sctp: add SCTP_FUTURE_ASSOC for SCTP_PEER_ADDR_THLDS sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of TCA_HHF_NON_HH_WEIGHT or TCA_HHF_QUANTUM is zero,
it would make no progress inside the loop in hhf_dequeue() thus
kernel would get stuck.
Fix this by checking this corner case in hhf_change().
Fixes: 10239edf86 ("net-qdisc-hhf: Heavy-Hitter Filter (HHF) qdisc")
Reported-by: syzbot+bc6297c11f19ee807dc2@syzkaller.appspotmail.com
Reported-by: syzbot+041483004a7f45f1f20a@syzkaller.appspotmail.com
Reported-by: syzbot+55be5f513bed37fc4367@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Terry Lam <vtlam@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least sch_red and sch_tbf don't implement ->tcf_block()
while still have a non-zero tc "class".
Instead of adding nop implementations to each of such qdisc's,
we can just relax the check of cops->tcf_block() in
tc_bind_tclass(). They don't support TC filter anyway.
Reported-by: syzbot+21b29db13c065852f64b@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the
device reset policy on driver probe.
This parameter is useful in conjunction with the existing
'fw_load_policy' parameter.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent at the end.
In fact, NLMSG_DONE is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 949f1e39a6 ("bridge: mdb: notify on router port add and del")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nft_offload_init() and nft_offload_exit() function to deal with the
init and the exit path of the offload infrastructure.
Rename nft_indr_block_get_and_ing_cmd() to nft_indr_block_cb().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nft_offload_ctx structure is much too large to put on the
stack:
net/netfilter/nf_tables_offload.c:31:23: error: stack frame size of 1200 bytes in function 'nft_flow_rule_create' [-Werror,-Wframe-larger-than=]
Use dynamic allocation here, as we do elsewhere in the same
function.
Fixes: c9626a2cbd ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The "newobj" is an error pointer so we can't pass it to kfree(). It
doesn't need to be freed so we can remove that and I also renamed the
error label.
Fixes: d62d0ba97b ("netfilter: nf_tables: Introduce stateful object update operation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unlike normal TCP code TLS has to touch the cache lines
it copies into to fill header info. On memory-heavy workloads
having non temporal stores and normal accesses targeting
the same cache line leads to significant overhead.
Measured 3% overhead running 3600 round robin connections
with additional memory heavy workload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TLS device offload the tag/message authentication code are
filled in by the device. The kernel merely reserves space for
them. Because device overwrites it, the contents of the tag make
do no matter. Current code tries to save space by reusing the
header as the tag. This, however, leads to an additional frag
being created and defeats buffer coalescing (which trickles
all the way down to the drivers).
Remove this optimization, and try to allocate the space for
the tag in the usual way, leave the memory uninitialized.
If memory allocation fails rewind the record pointer so that
we use the already copied user data as tag.
Note that the optimization was actually buggy, as the tag
for TLS 1.2 is 16 bytes, but header is just 13, so the reuse
may had looked past the end of the page..
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All modifications to TLS record list happen under the socket
lock. Since records form an ordered queue readers are only
concerned about elements being removed, additions can happen
concurrently.
Use RCU primitives to ensure the correct access types
(READ_ONCE/WRITE_ONCE).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's generally more cache friendly to walk arrays in order,
especially those which are likely not in cache.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-09-06
Here's the main bluetooth-next pull request for the 5.4 kernel.
- Cleanups & fixes to btrtl driver
- Fixes for Realtek devices in btusb, e.g. for suspend handling
- Firmware loading support for BCM4345C5
- hidp_send_message() return value handling fixes
- Added support for utilizing Fast Advertising Interval
- Various other minor cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, support for frag_list packets entering skb_segment() was
limited to frag_list members terminating on exact same gso_size
boundaries. This is verified with a BUG_ON since commit 89319d3801
("net: Add frag_list support to skb_segment"), quote:
As such we require all frag_list members terminate on exact MSS
boundaries. This is checked using BUG_ON.
As there should only be one producer in the kernel of such packets,
namely GRO, this requirement should not be difficult to maintain.
However, since commit 6578171a7f ("bpf: add bpf_skb_change_proto helper"),
the "exact MSS boundaries" assumption no longer holds:
An eBPF program using bpf_skb_change_proto() DOES modify 'gso_size', but
leaves the frag_list members as originally merged by GRO with the
original 'gso_size'. Example of such programs are bpf-based NAT46 or
NAT64.
This lead to a kernel BUG_ON for flows involving:
- GRO generating a frag_list skb
- bpf program performing bpf_skb_change_proto() or bpf_skb_adjust_room()
- skb_segment() of the skb
See example BUG_ON reports in [0].
In commit 13acc94eff ("net: permit skb_segment on head_frag frag_list skb"),
skb_segment() was modified to support the "gso_size mangling" case of
a frag_list GRO'ed skb, but *only* for frag_list members having
head_frag==true (having a page-fragment head).
Alas, GRO packets having frag_list members with a linear kmalloced head
(head_frag==false) still hit the BUG_ON.
This commit adds support to skb_segment() for a 'head_skb' packet having
a frag_list whose members are *non* head_frag, with gso_size mangled, by
disabling SG and thus falling-back to copying the data from the given
'head_skb' into the generated segmented skbs - as suggested by Willem de
Bruijn [1].
Since this approach involves the penalty of skb_copy_and_csum_bits()
when building the segments, care was taken in order to enable this
solution only when required:
- untrusted gso_size, by testing SKB_GSO_DODGY is set
(SKB_GSO_DODGY is set by any gso_size mangling functions in
net/core/filter.c)
- the frag_list is non empty, its item is a non head_frag, *and* the
headlen of the given 'head_skb' does not match the gso_size.
[0]
https://lore.kernel.org/netdev/20190826170724.25ff616f@pixies/https://lore.kernel.org/netdev/9265b93f-253d-6b8c-f2b8-4b54eff1835c@fb.com/
[1]
https://lore.kernel.org/netdev/CA+FuTSfVsgNDi7c=GUU8nMg2hWxF2SjCNLXetHeVPdnxAW5K-w@mail.gmail.com/
Fixes: 6578171a7f ("bpf: add bpf_skb_change_proto helper")
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a re-post of previous patch wrote by David Miller[1].
Phil Karn reported[2] that on busy networks with lots of unresolved
multicast routing entries, the creation of new multicast group routes
can be extremely slow and unreliable.
The reason is we hard-coded multicast route entries with unresolved source
addresses(cache_resolve_queue_len) to 10. If some multicast route never
resolves and the unresolved source addresses increased, there will
be no ability to create new multicast route cache.
To resolve this issue, we need either add a sysctl entry to make the
cache_resolve_queue_len configurable, or just remove cache_resolve_queue_len
limit directly, as we already have the socket receive queue limits of mrouted
socket, pointed by David.
>From my side, I'd perfer to remove the cache_resolve_queue_len limit instead
of creating two more(IPv4 and IPv6 version) sysctl entry.
[1] https://lkml.org/lkml/2018/7/22/11
[2] https://lkml.org/lkml/2018/7/21/343
v3: instead of remove cache_resolve_queue_len totally, let's only remove
the hard code limit when allocate the unresolved cache, as Eric Dumazet
suggested, so we don't need to re-count it in other places.
v2: hold the mfc_unres_lock while walking the unresolved list in
queue_count(), as Nikolay Aleksandrov remind.
Reported-by: Phil Karn <karn@ka9q.net>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a stupid bug I recently introduced...
ip6_route_info_create() returns an ERR_PTR(err) and not a NULL on error.
Fixes: d55a2e374a ("net-ipv6: fix excessive RTF_ADDRCONF flag on ::1/128 local route (and others)'")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_diag_get_aux_size() can be called with sockets in any state.
icsk_ulp_ops is only present for full sockets.
For SYN_RECV or TIME_WAIT ones we would access garbage.
Fixes: 61723b3932 ("tcp: ulp: add functions to dump ulp-specific information")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Luke Hsiao <lukehsiao@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need for fib_notifier_ops to be in struct net. It is used only by
fib_notifier as a private data. Use net_generic to introduce per-net
fib_notifier struct and move fib_notifier_ops there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add nft_reg_store64() and nft_reg_load64() helpers, from Ander Juaristi.
2) Time matching support, also from Ander Juaristi.
3) VLAN support for nfnetlink_log, from Michael Braun.
4) Support for set element deletions from the packet path, also from Ander.
5) Remove __read_mostly from conntrack spinlock, from Li RongQing.
6) Support for updating stateful objects, this also includes the initial
client for this infrastructure: the quota extension. A follow up fix
for the control plane also comes in this batch. Patches from
Fernando Fernandez Mancera.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of invoking struct bpf_prog::bpf_func directly, use the
BPF_PROG_RUN macro.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hidp_send_message was changed to return non-zero values on success,
which some other bits did not expect. This caused spurious errors to be
propagated through the stack, breaking some drivers, such as hid-sony
for the Dualshock 4 in Bluetooth mode.
As pointed out by Dan Carpenter, hid-microsoft directly relied on that
assumption as well.
Fixes: 48d9cc9d85 ("Bluetooth: hidp: Let hidp_send_message return number of queued bytes")
Signed-off-by: Dan Elkouby <streetwalkermc@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Whenever MQ is not used on a multiqueue device, we experience
serious reordering problems. Bisection found the cited
commit.
The issue can be described this way :
- A single qdisc hierarchy is shared by all transmit queues.
(eg : tc qdisc replace dev eth0 root fq_codel)
- When/if try_bulk_dequeue_skb_slow() dequeues a packet targetting
a different transmit queue than the one used to build a packet train,
we stop building the current list and save the 'bad' skb (P1) in a
special queue. (bad_txq)
- When dequeue_skb() calls qdisc_dequeue_skb_bad_txq() and finds this
skb (P1), it checks if the associated transmit queues is still in frozen
state. If the queue is still blocked (by BQL or NIC tx ring full),
we leave the skb in bad_txq and return NULL.
- dequeue_skb() calls q->dequeue() to get another packet (P2)
The other packet can target the problematic queue (that we found
in frozen state for the bad_txq packet), but another cpu just ran
TX completion and made room in the txq that is now ready to accept
new packets.
- Packet P2 is sent while P1 is still held in bad_txq, P1 might be sent
at next round. In practice P2 is the lead of a big packet train
(P2,P3,P4 ...) filling the BQL budget and delaying P1 by many packets :/
To solve this problem, we have to block the dequeue process as long
as the first packet in bad_txq can not be sent. Reordering issues
disappear and no side effects have been seen.
Fixes: a53851e2c3 ("net: sched: explicit locking in gso_cpu fallback")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-09-05
1) Several xfrm interface fixes from Nicolas Dichtel:
- Avoid an interface ID corruption on changelink.
- Fix wrong intterface names in the logs.
- Fix a list corruption when changing network namespaces.
- Fix unregistation of the underying phydev.
2) Fix a potential warning when merging xfrm_plocy nodes.
From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For high speed adapter like Mellanox CX-5 card, it can reach upto
100 Gbits per second bandwidth. Currently htb already supports 64bit rate
in tc utility. However police action rate and peakrate are still limited
to 32bit value (upto 32 Gbits per second). Add 2 new attributes
TCA_POLICE_RATE64 and TCA_POLICE_RATE64 in kernel for 64bit support
so that tc utility can use them for 64bit rate and peakrate value to
break the 32bit limit, and still keep the backward binary compatibility.
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Signed-off-by: David Dai <zdai@linux.vnet.ibm.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloaded OvS datapath rules are translated one to one to tc rules,
for example the following simplified OvS rule:
recirc_id(0),in_port(dev1),eth_type(0x0800),ct_state(-trk) actions:ct(),recirc(2)
Will be translated to the following tc rule:
$ tc filter add dev dev1 ingress \
prio 1 chain 0 proto ip \
flower tcp ct_state -trk \
action ct pipe \
action goto chain 2
Received packets will first travel though tc, and if they aren't stolen
by it, like in the above rule, they will continue to OvS datapath.
Since we already did some actions (action ct in this case) which might
modify the packets, and updated action stats, we would like to continue
the proccessing with the correct recirc_id in OvS (here recirc_id(2))
where we left off.
To support this, introduce a new skb extension for tc, which
will be used for translating tc chain to ovs recirc_id to
handle these miss cases. Last tc chain index will be set
by tc goto chain action and read by OvS datapath.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct mgmt_rp_get_connections {
...
struct mgmt_addr_info addr[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*rp) + (i * sizeof(struct mgmt_addr_info));
with:
struct_size(rp, addr, i)
Also, notice that, in this case, variable rp_len is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static variable header_ops, of type header_ops, is used only once, when
it is assigned to field header_ops of a variable having type net_device.
This corresponding field is declared as const in the definition of
net_device. Hence make header_ops constant as well to protect it from
unnecessary modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.
A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).
- Non-Discoverable Mode
- Non-Connectable Mode
- Limited Discoverable Mode
- General Discoverable Mode
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When accessing the members of an XDP socket, the control mutex should
be held. This commit fixes that.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Fixes: a36b38aa2a ("xsk: add sock_diag interface for AF_XDP")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Prior the state variable was introduced by Ilya, the dev member was
used to determine whether the socket was bound or not. However, when
dev was read, proper SMP barriers and READ_ONCE were missing. In order
to address the missing barriers and READ_ONCE, we start using the
state variable as a point of synchronization. The state member
read/write is paired with proper SMP barriers, and from this follows
that the members described above does not need READ_ONCE if used in
conjunction with state check.
In all syscalls and the xsk_rcv path we check if state is
XSK_BOUND. If that is the case we do a SMP read barrier, and this
implies that the dev, umem and all rings are correctly setup. Note
that no READ_ONCE are needed for these variable if used when state is
XSK_BOUND (plus the read barrier).
To summarize: The members struct xdp_sock members dev, queue_id, umem,
fq, cq, tx, rx, and state were read lock-less, with incorrect barriers
and missing {READ, WRITE}_ONCE. Now, umem, fq, cq, tx, rx, and state
are read lock-less. When these members are updated, WRITE_ONCE is
used. When read, READ_ONCE are only used when read outside the control
mutex (e.g. mmap) or, not synchronized with the state member
(XSK_BOUND plus smp_rmb())
Note that dev and queue_id do not need a WRITE_ONCE or READ_ONCE, due
to the introduce state synchronization (XSK_BOUND plus smp_rmb()).
Introducing the state check also fixes a race, found by syzcaller, in
xsk_poll() where umem could be accessed when stale.
Suggested-by: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+c82697e3043781e08802@syzkaller.appspotmail.com
Fixes: 77cd0d7b3f ("xsk: add support for need_wakeup flag in AF_XDP rings")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The umem member of struct xdp_sock is read outside of the control
mutex, in the mmap implementation, and needs a WRITE_ONCE to avoid
potential store-tearing.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Fixes: 423f38329d ("xsk: add umem fill queue support and mmap")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use WRITE_ONCE when doing the store of tx, rx, fq, and cq, to avoid
potential store-tearing. These members are read outside of the control
mutex in the mmap implementation.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Fixes: 37b076933a ("xsk: add missing write- and data-dependency barrier")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Not all objects have an update operation. If the object type doesn't
implement an update operation and the user tries to update it will hit
EOPNOTSUPP.
Fixes: d62d0ba97b ("netfilter: nf_tables: Introduce stateful object update operation")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1vrJITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIC8BB/98XcWiaInD+SM6UjD2dVd1r0zhPKJS
WBK58G81+op3YP4DY8Iy+C24uZBlSlutVGoD/PIrZF39xXsnOtJuMVHC4LvtdADC
30uI/61JQNEjuX2AiTFudqDvYjZZKZ28HLqEnO2pWk3dMVL3+fkS3i7VQR7KJ/Gr
BYM6EzCdkbuWW/zsAVbKLJ8NswVmcdjP7eSK+exKppoWMtgCglZw1X6iP5YXDnbK
h3dGs687u8RfUra7j7vgnJzyQU4draMPsabaLDT5qw1PgYQ3k8MTVMBlULR0+HHO
qkBqumRwfOxay0z0XOgRuWrICKTH/b0SRLp3H53ZyfDo6+4TC9KGHRgX
=gwfZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.4-20190904' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-09-04 j1939
this is a pull request for net-next/master consisting of 21 patches.
the first 12 patches are by me and target the CAN core infrastructure.
They clean up the names of variables , structs and struct members,
convert can_rx_register() to use max() instead of open coding it and
remove unneeded code from the can_pernet_exit() callback.
The next three patches are also by me and they introduce and make use of
the CAN midlayer private structure. It is used to hold protocol specific
per device data structures.
The next patch is by Oleksij Rempel, switches the
&net->can.rcvlists_lock from a spin_lock() to a spin_lock_bh(), so that
it can be used from NAPI (soft IRQ) context.
The next 4 patches are by Kurt Van Dijck, he first updates his email
address via mailmap and then extends sockaddr_can to include j1939
members.
The final patch is the collective effort of many entities (The j1939
authors: Oliver Hartkopp, Bastian Stender, Elenita Hinds, kbuild test
robot, Kurt Van Dijck, Maxime Jayat, Robin van der Gracht, Oleksij
Rempel, Marc Kleine-Budde). It adds support of SAE J1939 protocol to the
CAN networking stack.
SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.
P.S.: This pull request doesn't invalidate my last pull request:
"pull-request: can-next 2019-09-03".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A change to the core nla helpers was missed during the push of
the nexthop changes. rt6_fill_node_nexthop should be calling
nla_nest_start_noflag not nla_nest_start. Currently, iproute2
does not print multipath data because of parsing issues with
the attribute.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_map and ULP only work together when ULP is loaded after the sock
map is loaded. In the sock_map case we added a check for this to fail
the load if ULP is already set. However, we missed the check on the
sock_hash side.
Add a ULP check to the sock_hash update path.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: syzbot+7a6ee4d0078eac6bf782@syzkaller.appspotmail.com
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment we have is just repeating what the code does.
Include the *reason* for the condition instead.
Cc: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If retransmit record hint fall into the cleanup window we will
free it by just walking the list. No need to duplicate the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS code has a number of #ifdefs which make the code a little
harder to follow. Recent fixes removed the ifdef around the
TLS_HW define, so we can switch to the often used pattern
of defining tls_device functions as empty static inlines
in the header when CONFIG_TLS_DEVICE=n.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On setsockopt path we need to hold device_offload_lock from
the moment we check netdev is up until the context is fully
ready to be added to the tls_device_list.
No need to hold it around the get_netdev_for_sock().
Change the code and remove the confusing comment.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reusing parts of error path for normal exit will make
next commit harder to read, untangle the two.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we already have the pointer to the full original sk_proto
stored use that instead of storing all individual callback
pointers as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IN_MULTICAST's primary intent is as a uapi macro.
Elsewhere in the kernel we use ipv4_is_multicast consistently.
This patch unifies linux's multicast checks to use that function
rather than this macro.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable port_rate is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2019-09-05
Here are a few more Bluetooth fixes for 5.3. I hope they can still make
it. There's one USB ID addition for btusb, two reverts due to discovered
regressions, and two other important fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c49a8682fc.
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is a subtle change in behaviour introduced by:
commit c7a1ce397a
'ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create'
Before that patch /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000003 00000000 80200001 lo
Afterwards /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80240001 lo
ie. the above commit causes the ::1/128 local (automatic) route to be flagged with RTF_ADDRCONF (0x040000).
AFAICT, this is incorrect since these routes are *not* coming from RA's.
As such, this patch restores the old behaviour.
Fixes: c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transport should use its own pf_retrans to do the error_count
check, instead of asoc's. Otherwise, it's meaningless to make
pf_retrans per transport.
Fixes: 5aa93bcf66 ("sctp: Implement quick failover draft from tsvwg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a misplaced traceline in rxrpc_input_packet() which is looking at a
packet that just got released rather than the replacement packet.
Fix this by moving the traceline after the assignment that moves the new
packet pointer to the actual packet pointer.
Fixes: d0d5c0cd1e ("rxrpc: Use skb_unshare() rather than skb_cow_data()")
Reported-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.
J1939, ISO 11783 and NMEA 2000 all share the same high level protocol.
SAE J1939 can be considered the replacement for the older SAE J1708 and
SAE J1587 specifications.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Elenita Hinds <ecathinds@gmail.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The size of this structure will be increased with J1939 support. To stay
binary compatible, the CAN_REQUIRED_SIZE macro is introduced for
existing CAN protocols.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The can_rx_unregister() can be called from NAPI (soft IRQ) context, at least
by j1939 stack. This leads to potential dead lock with &net->can.rcvlists_lock
called from can_rx_register:
===============================================================================
WARNING: inconsistent lock state
4.19.0-20181029-1-g3e67f95ba0d3 #3 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
testj1939/224 [HC0[0]:SC1[1]:HE1:SE0] takes:
1ad0fda3 (&(&net->can.rcvlists_lock)->rlock){+.?.}, at: can_rx_unregister+0x4c/0x1ac
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0xd0/0x1f4
_raw_spin_lock+0x30/0x40
can_rx_register+0x5c/0x14c
j1939_netdev_start+0xdc/0x1f8
j1939_sk_bind+0x18c/0x1c8
__sys_bind+0x70/0xb0
sys_bind+0x10/0x14
ret_fast_syscall+0x0/0x28
0xbedc9b64
irq event stamp: 2440
hardirqs last enabled at (2440): [<c01302c0>] __local_bh_enable_ip+0xac/0x184
hardirqs last disabled at (2439): [<c0130274>] __local_bh_enable_ip+0x60/0x184
softirqs last enabled at (2412): [<c08b0bf4>] release_sock+0x84/0xa4
softirqs last disabled at (2415): [<c013055c>] irq_exit+0x100/0x1b0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&net->can.rcvlists_lock)->rlock);
<Interrupt>
lock(&(&net->can.rcvlists_lock)->rlock);
*** DEADLOCK ***
2 locks held by testj1939/224:
#0: 168eb13b (rcu_read_lock){....}, at: netif_receive_skb_internal+0x3c/0x350
#1: 168eb13b (rcu_read_lock){....}, at: can_receive+0x88/0x1c0
===============================================================================
To avoid this situation, we should use spin_lock_bh() instead of spin_lock().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since using the "struct can_ml_priv" for the per device "struct
dev_rcv_lists" the call can_dev_rcv_lists_find() cannot fail anymore.
This patch simplifies af_can by removing the NULL pointer checks from
the dev_rcv_lists returned by can_dev_rcv_lists_find().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes the old method of allocating the per device protocol
specific memory via a netdevice_notifier. This had the drawback, that
the allocation can fail, leading to a lot of null pointer checks in the
code. This also makes the live cycle management of this memory quite
complicated.
This patch switches from the allocating the struct can_dev_rcv_lists in
a NETDEV_REGISTER call to using the dev->ml_priv, which is allocated by
the driver since the previous patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch introduces the CAN midlayer private structure ("struct
can_ml_priv") which should be used to hold protocol specific per device
data structures. For now it's only member is "struct can_dev_rcv_lists".
The CAN midlayer private is allocated via alloc_netdev()'s private and
assigned to "struct net_device::ml_priv" during device creation. This is
done transparently for CAN drivers using alloc_candev(). The slcan, vcan
and vxcan drivers which are not using alloc_candev() have been adopted
manually. The memory layout of the netdev_priv allocated via
alloc_candev() will looke like this:
+-------------------------+
| driver's priv |
+-------------------------+
| struct can_ml_priv |
+-------------------------+
| array of struct sk_buff |
+-------------------------+
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The networking core takes care and unregisters every network device in
a namespace before calling the can_pernet_exit() hook. This patch
removes the unneeded cleanup.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Suggested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces an open coded max by the proper kernel define max().
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the variables holding the CAN receiver and the receiver
list a better name by renaming them from "r to "rcv" and "rl" to
"recv_list".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add the commonly used prefix "can_" to the find_dev_rcv_lists()
function and moves the "find" to the end, as the function returns a struct
can_dev_rcv_list. This improves the overall readability of the code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add the commonly used prefix "can_" to the find_rcv_list()
function and add the "find" to the end, as the function returns a struct
rcv_list. This improves the overall readability of the code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the variables holding the CAN per device receive filter lists
a better name by renaming them from "d" to "dev_rcv_lists".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the variables holding the CAN receive filter lists a
better name by renaming them from "d" to "dev_rcv_lists".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch improves the code reability by removing the redundant "can_"
prefix from the members of struct netns_can (as the struct netns_can itself
is the member "can" of the struct net.)
The conversion is done with:
sed -i \
-e "s/struct can_dev_rcv_lists \*can_rx_alldev_list;/struct can_dev_rcv_lists *rx_alldev_list;/" \
-e "s/spinlock_t can_rcvlists_lock;/spinlock_t rcvlists_lock;/" \
-e "s/struct timer_list can_stattimer;/struct timer_list stattimer; /" \
-e "s/can\.can_rx_alldev_list/can.rx_alldev_list/g" \
-e "s/can\.can_rcvlists_lock/can.rcvlists_lock/g" \
-e "s/can\.can_stattimer/can.stattimer/g" \
include/net/netns/can.h \
net/can/*.[ch]
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch rename the variables holding the CAN statistics (can_stats
and can_pstats) to pkg_stats and rcv_lists_stats which reflect better
their meaning.
The conversion is done with:
sed -i \
-e "s/can_stats\([^_]\)/pkg_stats\1/g" \
-e "s/can_pstats/rcv_lists_stats/g" \
net/can/proc.c
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch rename the variables holding the CAN statistics (can_stats
and can_pstats) to pkg_stats and rcv_lists_stats which reflect better
their meaning.
The conversion is done with:
sed -i \
-e "s/can_stats\([^_]\)/pkg_stats\1/g" \
-e "s/can_pstats/rcv_lists_stats/g" \
net/can/af_can.c
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the members of the struct netns_can that are holding
the statistics a sensible name, by renaming struct netns_can::can_stats
into struct netns_can::pkg_stats and struct netns_can::can_pstats into
struct netns_can::rcv_lists_stats.
The conversion is done with:
sed -i \
-e "s:\(struct[^*]*\*\)can_stats;.*:\1pkg_stats;:" \
-e "s:\(struct[^*]*\*\)can_pstats;.*:\1rcv_lists_stats;:" \
-e "s/can\.can_stats/can.pkg_stats/g" \
-e "s/can\.can_pstats/can.rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames both "struct s_stats" and "struct s_pstats", to
"struct can_pkg_stats" and "struct can_rcv_lists_stats" to better
reflect their meaning and improve code readability.
The conversion is done with:
sed -i \
-e "s/struct s_stats/struct can_pkg_stats/g" \
-e "s/struct s_pstats/struct can_rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Set up the default timeout for this new entry otherwise the garbage
collector might quickly remove it right after the flowtable insertion.
Fixes: ac2a66665e ("netfilter: add generic flow table infrastructure")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If this flag is set, timeout and state are irrelevant to userspace.
Fixes: 90964016e5 ("netfilter: nf_conntrack: add IPS_OFFLOAD status bit")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If IPv6 is disabled on boot (ipv6.disable=1), but nft_fib_inet ends up
dealing with a IPv6 packet, it causes a kernel panic in
fib6_node_lookup_1(), crashing in bad_page_fault.
The panic is caused by trying to deference a very low address (0x38
in ppc64le), due to ipv6.fib6_main_tbl = NULL.
BUG: Kernel NULL pointer dereference at 0x00000038
The kernel panic was reproduced in a host that disabled IPv6 on boot and
have to process guest packets (coming from a bridge) using it's ip6tables.
Terminate rule evaluation when packet protocol is IPv6 but the ipv6 module
is not loaded.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the infrastructure needed for the stateful object update
support.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The p9_tag_alloc() does not initialize the transport error t_err field.
The struct p9_req_t *req is allocated and stored in a struct p9_client
variable. The field t_err is never initialized before p9_conn_cancel()
checks its value.
KUMSAN(KernelUninitializedMemorySantizer, a new error detection tool)
reports this bug.
==================================================================
BUG: KUMSAN: use of uninitialized memory in p9_conn_cancel+0x2d9/0x3b0
Read of size 4 at addr ffff88805f9b600c by task kworker/1:2/1216
CPU: 1 PID: 1216 Comm: kworker/1:2 Not tainted 5.2.0-rc4+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
Workqueue: events p9_write_work
Call Trace:
dump_stack+0x75/0xae
__kumsan_report+0x17c/0x3e6
kumsan_report+0xe/0x20
p9_conn_cancel+0x2d9/0x3b0
p9_write_work+0x183/0x4a0
process_one_work+0x4d1/0x8c0
worker_thread+0x6e/0x780
kthread+0x1ca/0x1f0
ret_from_fork+0x35/0x40
Allocated by task 1979:
save_stack+0x19/0x80
__kumsan_kmalloc.constprop.3+0xbc/0x120
kmem_cache_alloc+0xa7/0x170
p9_client_prepare_req.part.9+0x3b/0x380
p9_client_rpc+0x15e/0x880
p9_client_create+0x3d0/0xac0
v9fs_session_init+0x192/0xc80
v9fs_mount+0x67/0x470
legacy_get_tree+0x70/0xd0
vfs_get_tree+0x4a/0x1c0
do_mount+0xba9/0xf90
ksys_mount+0xa8/0x120
__x64_sys_mount+0x62/0x70
do_syscall_64+0x6d/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff88805f9b6008
which belongs to the cache p9_req_t of size 144
The buggy address is located 4 bytes inside of
144-byte region [ffff88805f9b6008, ffff88805f9b6098)
The buggy address belongs to the page:
page:ffffea00017e6d80 refcount:1 mapcount:0 mapping:ffff888068b63740 index:0xffff88805f9b7d90 compound_mapcount: 0
flags: 0x100000000010200(slab|head)
raw: 0100000000010200 ffff888068b66450 ffff888068b66450 ffff888068b63740
raw: ffff88805f9b7d90 0000000000100001 00000001ffffffff 0000000000000000
page dumped because: kumsan: bad access detected
==================================================================
Link: http://lkml.kernel.org/r/20190613070854.10434-1-shuaibinglu@126.com
Signed-off-by: Lu Shuaibing <shuaibinglu@126.com>
[dominique.martinet@cea.fr: grouped the added init with the others]
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
The socket assignment is wrong, see skb_orphan():
When skb->destructor callback is not set, but skb->sk is set, this hits BUG().
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1651813
Fixes: 554ced0a6e ("netfilter: nf_tables: add support for native socket matching")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A kernel panic can happen if a host has disabled IPv6 on boot and have to
process guest packets (coming from a bridge) using it's ip6tables.
IPv6 packets need to be dropped if the IPv6 module is not loaded, and the
host ip6tables will be used.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0: 00000000 00000000 00000000 00000000
[ 2.275598] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.283729] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.290333] ---[ end trace ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes: 955222ca52 ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
Pointer iter is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds handlers for PLDM over NC-SI command response.
This enables NC-SI driver recognizes the packet type so the responses
don't get dropped as unknown packet type.
PLDM over NC-SI are not handled in kernel driver for now, but can be
passed back to user space via Netlink for further handling.
Signed-off-by: Ben Wei <benwei@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make core more readable with switch-case for various port flavours.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink port index attribute is returned to users as u32 through
netlink response.
Change index data type from 'unsigned' to 'unsigned int' to avoid
below checkpatch.pl warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
81: FILE: include/net/devlink.h:81:
+ unsigned index;
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an application configures kernel TLS on top of a TCP socket, it's
now possible for inet_diag_handler() to collect information regarding the
protocol version, the cipher type and TX / RX configuration, in case
INET_DIAG_INFO is requested.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit b37e88407c ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure context does not get freed while diag
code is interrogating it. Free struct tls_context with
kfree_rcu().
We add the __rcu annotation directly in icsk, and cast it
away in the datapath accessor. Presumably all ULPs will
do a similar thing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The discussion to be made is absolutely the same as in the case of
previous patch ("taprio: Set default link speed to 10 Mbps in
taprio_set_picos_per_byte"). Nothing is lost when setting a default.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: e0a7683d30 ("net/sched: cbs: fix port_rate miscalculation")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio budget needs to be adapted at runtime according to interface
link speed. But that handling is problematic.
For one thing, installing a qdisc on an interface that doesn't have
carrier is not illegal. But taprio prints the following stack trace:
[ 31.851373] ------------[ cut here ]------------
[ 31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4
[ 31.864566] taprio: dequeue() called with unknown picos per byte.
[ 31.864570] Modules linked in:
[ 31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689
[ 31.881398] Hardware name: Freescale LS1021A
[ 31.885661] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 31.893368] [<c030d8cc>] (show_stack) from [<c10ac958>] (dump_stack+0xb4/0xc8)
[ 31.900555] [<c10ac958>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 31.907395] [<c0349d04>] (__warn) from [<c0349d64>] (warn_slowpath_fmt+0x48/0x6c)
[ 31.914841] [<c0349d64>] (warn_slowpath_fmt) from [<c0f38db4>] (taprio_dequeue+0x1a8/0x2d4)
[ 31.923150] [<c0f38db4>] (taprio_dequeue) from [<c0f227b0>] (__qdisc_run+0x90/0x61c)
[ 31.930856] [<c0f227b0>] (__qdisc_run) from [<c0ec82ac>] (net_tx_action+0x12c/0x2bc)
[ 31.938560] [<c0ec82ac>] (net_tx_action) from [<c0302298>] (__do_softirq+0x130/0x3c8)
[ 31.946350] [<c0302298>] (__do_softirq) from [<c03502a0>] (irq_exit+0xbc/0xd8)
[ 31.953536] [<c03502a0>] (irq_exit) from [<c03a4808>] (__handle_domain_irq+0x60/0xb4)
[ 31.961328] [<c03a4808>] (__handle_domain_irq) from [<c0754478>] (gic_handle_irq+0x58/0x9c)
[ 31.969638] [<c0754478>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 31.977076] Exception stack(0xe8167b20 to 0xe8167b68)
[ 31.982100] 7b20: e9d4bd80 00000cc0 000000cf 00000000 e9d4bd80 c1f38958 00000cc0 c1f38960
[ 31.990234] 7b40: 00000001 000000cf 00000004 e9dc0800 00000000 e8167b70 c0f478ec c0f46d94
[ 31.998363] 7b60: 60070013 ffffffff
[ 32.001833] [<c0301a8c>] (__irq_svc) from [<c0f46d94>] (netlink_trim+0x18/0xd8)
[ 32.009104] [<c0f46d94>] (netlink_trim) from [<c0f478ec>] (netlink_broadcast_filtered+0x34/0x414)
[ 32.017930] [<c0f478ec>] (netlink_broadcast_filtered) from [<c0f47cec>] (netlink_broadcast+0x20/0x28)
[ 32.027102] [<c0f47cec>] (netlink_broadcast) from [<c0eea378>] (rtnetlink_send+0x34/0x88)
[ 32.035238] [<c0eea378>] (rtnetlink_send) from [<c0f25890>] (notify_and_destroy+0x2c/0x44)
[ 32.043461] [<c0f25890>] (notify_and_destroy) from [<c0f25e08>] (qdisc_graft+0x398/0x470)
[ 32.051595] [<c0f25e08>] (qdisc_graft) from [<c0f27a00>] (tc_modify_qdisc+0x3a4/0x724)
[ 32.059470] [<c0f27a00>] (tc_modify_qdisc) from [<c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec)
[ 32.067864] [<c0ee4c84>] (rtnetlink_rcv_msg) from [<c0f4a988>] (netlink_rcv_skb+0xb8/0x110)
[ 32.076172] [<c0f4a988>] (netlink_rcv_skb) from [<c0f4a170>] (netlink_unicast+0x1b4/0x22c)
[ 32.084392] [<c0f4a170>] (netlink_unicast) from [<c0f4a5e4>] (netlink_sendmsg+0x33c/0x380)
[ 32.092614] [<c0f4a5e4>] (netlink_sendmsg) from [<c0ea9f40>] (sock_sendmsg+0x14/0x24)
[ 32.100403] [<c0ea9f40>] (sock_sendmsg) from [<c0eaa780>] (___sys_sendmsg+0x214/0x228)
[ 32.108279] [<c0eaa780>] (___sys_sendmsg) from [<c0eabad0>] (__sys_sendmsg+0x50/0x8c)
[ 32.116068] [<c0eabad0>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[ 32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0)
[ 32.128960] 7fa0: b6fa68c8 000000f8 00000003 bea142d0 00000000 00000000
[ 32.137093] 7fc0: b6fa68c8 000000f8 0052154c 00000128 5d6468a2 00000000 00000028 00558c9c
[ 32.145224] 7fe0: 00000070 bea14278 00530d64 b6e17e64
[ 32.150659] ---[ end trace 2139c9827c3e5177 ]---
This happens because the qdisc ->dequeue callback gets called. Which
again is not illegal, the qdisc will dequeue even when the interface is
up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames
will be dropped further down the stack in dev_direct_xmit().
And, at the end of the day, for what? For calculating the initial budget
of an interface which is non-operational at the moment and where frames
will get dropped anyway.
So if we can't figure out the link speed, default to SPEED_10 and move
along. We can also remove the runtime check now.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: 7b9eba7ba0 ("net/sched: taprio: fix picos_per_byte miscalculation")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
taprio_init may fail earlier than this line:
list_add(&q->taprio_list, &taprio_list);
i.e. due to the net device not being multi queue.
Attempting to remove q from the global taprio_list when it is not part
of it will result in a kernel panic.
Fix it by matching list_add and list_del better to one another in the
order of operations. This way we can keep the deletion unconditional
and with lower complexity - O(1).
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: 7b9eba7ba0 ("net/sched: taprio: fix picos_per_byte miscalculation")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.
That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.
There are 2 parts to the issue.
First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic. Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.
Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this simplified code snippet fails:
br_vlan_get_pvid(netdev, &pvid);
br_vlan_get_info(netdev, pvid, &vinfo);
ASSERT(!(vinfo.flags & BRIDGE_VLAN_INFO_PVID));
It is intuitive that the pvid of a netdevice should have the
BRIDGE_VLAN_INFO_PVID flag set.
However I can't seem to pinpoint a commit where this behavior was
introduced. It seems like it's been like that since forever.
At a first glance it would make more sense to just handle the
BRIDGE_VLAN_INFO_PVID flag in __vlan_add_flags. However, as Nikolay
explains:
There are a few reasons why we don't do it, most importantly because
we need to have only one visible pvid at any single time, even if it's
stale - it must be just one. Right now that rule will not be violated
by this change, but people will try using this flag and could see two
pvids simultaneously. You can see that the pvid code is even using
memory barriers to propagate the new value faster and everywhere the
pvid is read only once. That is the reason the flag is set
dynamically when dumping entries, too. A second (weaker) argument
against would be given the above we don't want another way to do the
same thing, specifically if it can provide us with two pvids (e.g. if
walking the vlan list) or if it can provide us with a pvid different
from the one set in the vg. [Obviously, I'm talking about RCU
pvid/vlan use cases similar to the dumps. The locked cases are fine.
I would like to avoid explaining why this shouldn't be relied upon
without locking]
So instead of introducing the above change and making sure of the pvid
uniqueness under RCU, simply dynamically populate the pvid flag in
br_vlan_get_info().
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix OGM and OGMv2 header read boundary check,
by Sven Eckelmann (2 patches)
-----BEGIN PGP SIGNATURE-----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=hD2g
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20190830' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Fix OGM and OGMv2 header read boundary check,
by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Spurious warning when loading rules using the physdev match,
from Todd Seidelmann.
2) Fix FTP conntrack helper debugging output, from Thomas Jarosch.
3) Restore per-netns nf_conntrack_{acct,helper,timeout} sysctl knobs,
from Florian Westphal.
4) Clear skbuff timestamp from the flowtable datapath, also from Florian.
5) Fix incorrect byteorder of NFT_META_BRI_IIFVPROTO, from wenxu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, addresses are chunk size aligned. This means, we are very
restricted in terms of where we can place chunk within the umem. For
example, if we have a chunk size of 2k, then our chunks can only be placed
at 0,2k,4k,6k,8k... and so on (ie. every 2k starting from 0).
This patch introduces the ability to use unaligned chunks. With these
changes, we are no longer bound to having to place chunks at a 2k (or
whatever your chunk size is) interval. Since we are no longer dealing with
aligned chunks, they can now cross page boundaries. Checks for page
contiguity have been added in order to keep track of which pages are
followed by a physically contiguous page.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If a SYN cookie is not issued by tcp_v#_gen_syncookie, then the return
value will be exactly 0, rather than <= 0. Let's change the check to
reflect that, especially since mss is an unsigned value and cannot be
negative.
Fixes: 70d6624431 ("bpf: add bpf_tcp_gen_syncookie helper")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Petar Penkov <ppenkov@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Recent rtnl lock removal patch changed flow_action infra to require proper
cleanup besides simple memory deallocation. However, matchall classifier
was not updated to call tc_cleanup_flow_action(). Add proper cleanup to
mall_replace_hw_filter() and mall_reoffload().
Fixes: 5a6ff4b13d ("net: sched: take reference to action dev before calling offloads")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This explicitly clarifies that bbr_bdp() returns the rounded-up value of
the bandwidth-delay product and why in the comments.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Pengfei Liu <pengfeil@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a local endpoint is ceases to be in use, such as when the kafs module
is unloaded, the kernel will emit an assertion failure if there are any
outstanding client connections:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:433!
and even beyond that, will evince other oopses if there are service
connections still present.
Fix this by:
(1) Removing the triggering of connection reaping when an rxrpc socket is
released. These don't actually clean up the connections anyway - and
further, the local endpoint may still be in use through another
socket.
(2) Mark the local endpoint as dead when we start the process of tearing
it down.
(3) When destroying a local endpoint, strip all of its client connections
from the idle list and discard the ref on each that the list was
holding.
(4) When destroying a local endpoint, call the service connection reaper
directly (rather than through a workqueue) to immediately kill off all
outstanding service connections.
(5) Make the service connection reaper reap connections for which the
local endpoint is marked dead.
Only after destroying the connections can we close the socket lest we get
an oops in a workqueue that's looking at a connection or a peer.
Fixes: 3d18cbb7fd ("rxrpc: Fix conn expiry timers")
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=1xih
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20190827' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix use of skb_cow_data()
Here's a series of patches that replaces the use of skb_cow_data() in rxrpc
with skb_unshare() early on in the input process. The problem that is
being seen is that skb_cow_data() indirectly requires that the maximum
usage count on an sk_buff be 1, and it may generate an assertion failure in
pskb_expand_head() if not.
This can occur because rxrpc_input_data() may be still holding a ref when
it has just attached the sk_buff to the rx ring and given that attachment
its own ref. If recvmsg happens fast enough, skb_cow_data() can see the
ref still held by the softirq handler.
Further, a packet may contain multiple subpackets, each of which gets its
own attachment to the ring and its own ref - also making skb_cow_data() go
bang.
Fix this by:
(1) The DATA packet is currently parsed for subpackets twice by the input
routines. Parse it just once instead and make notes in the sk_buff
private data.
(2) Use the notes from (1) when attaching the packet to the ring multiple
times. Once the packet is attached to the ring, recvmsg can see it
and start modifying it, so the softirq handler is not permitted to
look inside it from that point.
(3) Pass the ref from the input code to the ring rather than getting an
extra ref. rxrpc_input_data() uses a ref on the second refcount to
prevent the packet from evaporating under it.
(4) Call skb_unshare() on secured DATA packets in rxrpc_input_packet()
before we take call->input_lock. Other sorts of packets don't get
modified and so can be left.
A trace is emitted if skb_unshare() eats the skb. Note that
skb_share() for our accounting in this regard as we can't see the
parameters in the packet to log in a trace line if it releases it.
(5) Remove the calls to skb_cow_data(). These are then no longer
necessary.
There are also patches to improve the rxrpc_skb tracepoint to make sure
that Tx-derived buffers are identified separately from Rx-derived buffers
in the trace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl1pLO8THGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi8ceB/4qXnsvkIfB7XMxg8KUXOtJiJPJX+j2
H8yFESAL7Qof3mJVmsnVREW0LBECxJbipSkFmsJtFgLMlGLAkGMvJQjrmp4EWlc7
OIMWirTkZHLUgWV485EXDerlL9XSyiTxQ3ccKLwQSSxeN+EBU8CnzYzw5rUy2pJl
n1RheF+nRn4sLeOggnXPbEEYHqyDcgOzVVBbP7dq0om8H8KV/1jz4w12Ybpm4BSb
s/3Sp9kSeT0VySlmoeSYly5/rNnYHgHzV5/qjEbzugVnqPrLTC+j9t3vJTpMoH7T
zum6Y41mxWLdXiiYAdccOmGEKXDXk2yxFEIVKwYBnsvLS1A11cXpuPdL
=3uNw
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.3-rc7' of git://github.com/ceph/ceph-client
Pull two ceph fixes from Ilya Dryomov:
"A fix for a -rc1 regression in rbd and a trivial static checker fix"
* tag 'ceph-for-5.3-rc7' of git://github.com/ceph/ceph-client:
rbd: restore zeroing past the overlap when reading from parent
libceph: don't call crypto_free_sync_skcipher() on a NULL tfm
This is useful for checking how much airtime is being used up by other
transmissions on the channel, e.g. by calculating (time_rx - time_bss_rx)
or (time_busy - time_bss_rx - time_tx)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190828102042.58016-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get the vlan_proto of ingress bridge in network byteorder as userspace
expects. Otherwise this is inconsistent with NFT_META_PROTOCOL.
Fixes: 2a3a93ef0b ("netfilter: nft_meta_bridge: Add NFT_META_BRI_IIFVPROTO support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The noencrypt flag was intended to be set if the "frame was received
unencrypted" according to include/uapi/linux/nl80211.h. However, the
current behavior is opposite of this.
Cc: stable@vger.kernel.org
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-3-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_deliver_skb_to_local_stack intercepts EAPoL frames if
mac80211 is configured to do so and forwards the contents over nl80211.
During this process some additional data is also forwarded, including
whether the frame was received encrypted or not. Unfortunately just
prior to the call to ieee80211_deliver_skb_to_local_stack, skb->cb is
cleared, resulting in incorrect data being exposed over nl80211.
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-2-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If 'fq' qdisc is used and a program has requested timestamps,
skb->tstamp needs to be cleared, else fq will treat these as
'transmit time'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
TCP associates tx timestamp requests with a byte in the bytestream.
If merging skbs in tcp_mtu_probe, migrate the tstamp request.
Similar to MSG_EOR, do not allow moving a timestamp from any segment
in the probe but the last. This to avoid merging multiple timestamps.
Tested with the packetdrill script at
https://github.com/wdebruij/packetdrill/commits/mtu_probe-1
Link: http://patchwork.ozlabs.org/patch/1143278/#2232897
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Action sample doesn't properly handle psample_group pointer in overwrite
case. Following issues need to be fixed:
- In tcf_sample_init() function RCU_INIT_POINTER() is used to set
s->psample_group, even though we neither setting the pointer to NULL, nor
preventing concurrent readers from accessing the pointer in some way.
Use rcu_swap_protected() instead to safely reset the pointer.
- Old value of s->psample_group is not released or deallocated in any way,
which results resource leak. Use psample_group_put() on non-NULL value
obtained with rcu_swap_protected().
- The function psample_group_put() that released reference to struct
psample_group pointed by rcu-pointer s->psample_group doesn't respect rcu
grace period when deallocating it. Extend struct psample_group with rcu
head and use kfree_rcu when freeing it.
Fixes: 5c5670fae4 ("net/sched: Introduce sample tc action")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first fragment in a datagram contains the L4 headers. When the
Open vSwitch module parses a packet, it always sets the IP protocol
field in the key, but can only set the L4 fields on the first fragment.
The original behavior would not clear the L4 portion of the key, so
garbage values would be sent in the key for "later" fragments. This
patch clears the L4 fields in that circumstance to prevent sending those
garbage values as part of the upcall.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP fragments are reassembled before being sent to conntrack, the
key from the last fragment is used. Unless there are reordering
issues, the last fragment received will not contain the L4 ports, so the
key for the reassembled datagram won't contain them. This patch updates
the key once we have a reassembled datagram.
The handle_fragments() function works on L3 headers so we pull the L3/L4
flow key update code from key_extract into a new function
'key_extract_l3l4'. Then we add a another new function
ovs_flow_key_update_l3l4() and export it so that it is accessible by
handle_fragments() for conntrack packet reassembly.
Co-authored-by: Justin Pettit <jpettit@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 'TCQ_F_CPUSTATS' bit can be cleared, depending on the value of
'TCQ_F_NOLOCK' bit in the parent qdisc, we need to be sure that per-cpu
counters are present when 'reset()' is called for pfifo_fast qdiscs.
Otherwise, the following script:
# tc q a dev lo handle 1: root htb default 100
# tc c a dev lo parent 1: classid 1:100 htb \
> rate 95Mbit ceil 100Mbit burst 64k
[...]
# tc f a dev lo parent 1: protocol arp basic classid 1:100
[...]
# tc q a dev lo parent 1:100 handle 100: pfifo_fast
[...]
# tc q d dev lo root
can generate the following splat:
Unable to handle kernel paging request at virtual address dfff2c01bd148000
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
[dfff2c01bd148000] address between user and kernel address ranges
Internal error: Oops: 96000004 [#1] SMP
[...]
pstate: 80000005 (Nzcv daif -PAN -UAO)
pc : pfifo_fast_reset+0x280/0x4d8
lr : pfifo_fast_reset+0x21c/0x4d8
sp : ffff800d09676fa0
x29: ffff800d09676fa0 x28: ffff200012ee22e4
x27: dfff200000000000 x26: 0000000000000000
x25: ffff800ca0799958 x24: ffff1001940f332b
x23: 0000000000000007 x22: ffff200012ee1ab8
x21: 0000600de8a40000 x20: 0000000000000000
x19: ffff800ca0799900 x18: 0000000000000000
x17: 0000000000000002 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: ffff1001b922e6e2
x11: 1ffff001b922e6e1 x10: 0000000000000000
x9 : 1ffff001b922e6e1 x8 : dfff200000000000
x7 : 0000000000000000 x6 : 0000000000000000
x5 : 1fffe400025dc45c x4 : 1fffe400025dc357
x3 : 00000c01bd148000 x2 : 0000600de8a40000
x1 : 0000000000000007 x0 : 0000600de8a40004
Call trace:
pfifo_fast_reset+0x280/0x4d8
qdisc_reset+0x6c/0x370
htb_reset+0x150/0x3b8 [sch_htb]
qdisc_reset+0x6c/0x370
dev_deactivate_queue.constprop.5+0xe0/0x1a8
dev_deactivate_many+0xd8/0x908
dev_deactivate+0xe4/0x190
qdisc_graft+0x88c/0xbd0
tc_get_qdisc+0x418/0x8a8
rtnetlink_rcv_msg+0x3a8/0xa78
netlink_rcv_skb+0x18c/0x328
rtnetlink_rcv+0x28/0x38
netlink_unicast+0x3c4/0x538
netlink_sendmsg+0x538/0x9a0
sock_sendmsg+0xac/0xf8
___sys_sendmsg+0x53c/0x658
__sys_sendmsg+0xc8/0x140
__arm64_sys_sendmsg+0x74/0xa8
el0_svc_handler+0x164/0x468
el0_svc+0x10/0x14
Code: 910012a0 92400801 d343fc03 11000c21 (38fb6863)
Fix this by testing the value of 'TCQ_F_CPUSTATS' bit in 'qdisc->flags',
before dereferencing 'qdisc->cpu_qstats'.
Changes since v1:
- coding style improvements, thanks to Stefano Brivio
Fixes: 8a53e616de ("net: sched: when clearing NOLOCK, clear TCQ_F_CPUSTATS, too")
CC: Paolo Abeni <pabeni@redhat.com>
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_secret(), key->tfm is assigned to NULL on line 55, and then
ceph_crypto_key_destroy(key) is executed.
ceph_crypto_key_destroy(key)
crypto_free_sync_skcipher(key->tfm)
crypto_free_skcipher(&tfm->base);
This happens to work because crypto_sync_skcipher is a trivial wrapper
around crypto_skcipher: &tfm->base is still 0 and crypto_free_skcipher()
handles that. Let's not rely on the layout of crypto_sync_skcipher.
This bug is found by a static analysis tool STCheck written by us.
Fixes: 69d6302b65 ("libceph: Remove VLA usage of skcipher").
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Vladimir Rutsky reported stuck TCP sessions after memory pressure
events. Edge Trigger epoll() user would never receive an EPOLLOUT
notification allowing them to retry a sendmsg().
Jason tested the case of sk_stream_alloc_skb() returning NULL,
but there are other paths that could lead both sendmsg() and sendpage()
to return -1 (EAGAIN), with an empty skb queued on the write queue.
This patch makes sure we remove this empty skb so that
Jason code can detect that the queue is empty, and
call sk->sk_write_space(sk) accordingly.
Fixes: ce5ec44099 ("tcp: ensure epoll edge trigger wakeup when write queue is empty")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Reported-by: Vladimir Rutsky <rutsky@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rds6_inc_info_copy() function has a couple struct members which
are leaking stack information. The ->tos field should hold actual
information and the ->flags field needs to be zeroed out.
Fixes: 3eb450367d ("rds: add type of service(tos) infrastructure")
Fixes: b7ff8b1036 ("rds: Extend RDS API for IPv6 support")
Reported-by: 黄ID蝴蝶 <butterflyhuangxx@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_ECN_SUPPORTED sockopt will be added to allow users to change
ep ecn flag, and it's similar with other feature flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl net.sctp.ecn_enable is added in this patch. It will allow
users to change the default sctp ecn flag, net.sctp.ecn_enable.
This feature was also required on this thread:
http://lkml.iu.edu/hypermail/linux/kernel/0812.1/01858.html
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.
asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After witnessing the discussion in https://lkml.org/lkml/2019/8/14/151
w.r.t. ioctl extensibility, it became clear that such an issue might
prevent that the 3 RSV bits inside the DSA 802.1Q tag might also suffer
the same fate and be useless for further extension.
So clearly specify that the reserved bits should currently be
transmitted as zero and ignored on receive. The DSA tagger already does
this (and has always did), and is the only known user so far (no
Wireshark dissection plugin, etc). So there should be no incompatibility
to speak of.
Fixes: 0471dd429c ("net: dsa: tag_8021q: Create a stable binary format")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net pointer in struct xt_tgdtor_param is not explicitly
initialized therefore is still NULL when dereferencing it.
So we have to find a way to pass the correct net pointer to
ipt_destroy_target().
The best way I find is just saving the net pointer inside the per
netns struct tcf_idrinfo, which could make this patch smaller.
Fixes: 0c66dc1ea3 ("netfilter: conntrack: register hooks in netns when needed by ruleset")
Reported-and-tested-by: itugrok@yahoo.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Stable fixes:
- Fix a page lock leak in nfs_pageio_resend()
- Ensure O_DIRECT reports an error if the bytes read/written is 0
- Don't handle errors if the bind/connect succeeded
- Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was invalidat
ed"
Bugfixes:
- Don't refresh attributes with mounted-on-file information
- Fix return values for nfs4_file_open() and nfs_finish_open()
- Fix pnfs layoutstats reporting of I/O errors
- Don't use soft RPC calls for pNFS/flexfiles I/O, and don't abort for
soft I/O errors when the user specifies a hard mount.
- Various fixes to the error handling in sunrpc
- Don't report writepage()/writepages() errors twice.
-----BEGIN PGP SIGNATURE-----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=YHhU
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix a page lock leak in nfs_pageio_resend()
- Ensure O_DIRECT reports an error if the bytes read/written is 0
- Don't handle errors if the bind/connect succeeded
- Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was
invalidat ed"
Bugfixes:
- Don't refresh attributes with mounted-on-file information
- Fix return values for nfs4_file_open() and nfs_finish_open()
- Fix pnfs layoutstats reporting of I/O errors
- Don't use soft RPC calls for pNFS/flexfiles I/O, and don't abort
for soft I/O errors when the user specifies a hard mount.
- Various fixes to the error handling in sunrpc
- Don't report writepage()/writepages() errors twice"
* tag 'nfs-for-5.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: remove set but not used variable 'mapping'
NFSv2: Fix write regression
NFSv2: Fix eof handling
NFS: Fix writepage(s) error handling to not report errors twice
NFS: Fix spurious EIO read errors
pNFS/flexfiles: Don't time out requests on hard mounts
SUNRPC: Handle connection breakages correctly in call_status()
Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was invalidated"
SUNRPC: Handle EADDRINUSE and ENOBUFS correctly
pNFS/flexfiles: Turn off soft RPC calls
SUNRPC: Don't handle errors if the bind/connect succeeded
NFS: On fatal writeback errors, we need to call nfs_inode_remove_request()
NFS: Fix initialisation of I/O result struct in nfs_pgio_rpcsetup
NFS: Ensure O_DIRECT reports an error if the bytes read/written is 0
NFSv4/pnfs: Fix a page lock leak in nfs_pageio_resend()
NFSv4: Fix return value in nfs_finish_open()
NFSv4: Fix return values for nfs4_file_open()
NFS: Don't refresh attributes with mounted-on-file information
Pull networking fixes from David Miller:
1) Use 32-bit index for tails calls in s390 bpf JIT, from Ilya
Leoshkevich.
2) Fix missed EPOLLOUT events in TCP, from Eric Dumazet. Same fix for
SMC from Jason Baron.
3) ipv6_mc_may_pull() should return 0 for malformed packets, not
-EINVAL. From Stefano Brivio.
4) Don't forget to unpin umem xdp pages in error path of
xdp_umem_reg(). From Ivan Khoronzhuk.
5) Fix sta object leak in mac80211, from Johannes Berg.
6) Fix regression by not configuring PHYLINK on CPU port of bcm_sf2
switches. From Florian Fainelli.
7) Revert DMA sync removal from r8169 which was causing regressions on
some MIPS Loongson platforms. From Heiner Kallweit.
8) Use after free in flow dissector, from Jakub Sitnicki.
9) Fix NULL derefs of net devices during ICMP processing across
collect_md tunnels, from Hangbin Liu.
10) proto_register() memory leaks, from Zhang Lin.
11) Set NLM_F_MULTI flag in multipart netlink messages consistently,
from John Fastabend.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
r8152: Set memory to all 0xFFs on failed reg reads
openvswitch: Fix conntrack cache with timeout
ipv4: mpls: fix mpls_xmit for iptunnel
nexthop: Fix nexthop_num_path for blackhole nexthops
net: rds: add service level support in rds-info
net: route dump netlink NLM_F_MULTI flag missing
s390/qeth: reject oversized SNMP requests
sock: fix potential memory leak in proto_register()
MAINTAINERS: Add phylink keyword to SFF/SFP/SFP+ MODULE SUPPORT
xfrm/xfrm_policy: fix dst dev null pointer dereference in collect_md mode
ipv4/icmp: fix rt dst dev null pointer dereference
openvswitch: Fix log message in ovs conntrack
bpf: allow narrow loads of some sk_reuseport_md fields with offset > 0
bpf: fix use after free in prog symbol exposure
bpf: fix precision tracking in presence of bpf2bpf calls
flow_dissector: Fix potential use-after-free on BPF_PROG_DETACH
Revert "r8169: remove not needed call to dma_sync_single_for_device"
ipv6: propagate ipv6_add_dev's error returns out of ipv6_find_idev
net/ncsi: Fix the payload copying for the request coming from Netlink
qed: Add cleanup in qed_slowpath_start()
...
when spinlock is locked/unlocked, its elements will be changed,
so marking it as __read_mostly is not suitable.
and remove a duplicate definition of nf_conntrack_locks_all_lock
strange that compiler does not complain.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When I merged the extension sysctl tables with the main one I forgot to
reset them on netns creation. They currently read/write init_net settings.
Fixes: d912dec124 ("netfilter: conntrack: merge acct and helper sysctl table with main one")
Fixes: cb2833ed00 ("netfilter: conntrack: merge ecache and timestamp sysctl tables with main one")
Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch implements the delete operation from the ruleset.
It implements a new delete() function in nft_set_rhash. It is simpler
to use than the already existing remove(), because it only takes the set
and the key as arguments, whereas remove() expects a full
nft_set_elem structure.
Signed-off-by: Ander Juaristi <a@juaristi.eus>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The find_pattern() debug output was printing the 'skip' character.
This can be a NULL-byte and messes up further pr_debug() output.
Output without the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to `<7>nf_conntrack_ftp: find_pattern `PORT': dlen = 8
kernel: nf_conntrack_ftp: find_pattern `EPRT': dlen = 8
Output with the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to 0x0 delimiter!
kernel: nf_conntrack_ftp: Match succeeded!
kernel: nf_conntrack_ftp: conntrack_ftp: match `172,17,0,100,200,207' (20 bytes at 4150681645)
kernel: nf_conntrack_ftp: find_pattern `PORT': dlen = 8
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simplify the check in physdev_mt_check() to emit an error message
only when passed an invalid chain (ie, NF_INET_LOCAL_OUT).
This avoids cluttering up the log with errors against valid rules.
For large/heavily modified rulesets, current behavior can quickly
overwhelm the ring buffer, because this function gets called on
every change, regardless of the rule that was changed.
Signed-off-by: Todd Seidelmann <tseidelmann@linode.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The in-place decryption routines in AF_RXRPC's rxkad security module
currently call skb_cow_data() to make sure the data isn't shared and that
the skb can be written over. This has a problem, however, as the softirq
handler may be still holding a ref or the Rx ring may be holding multiple
refs when skb_cow_data() is called in rxkad_verify_packet() - and so
skb_shared() returns true and __pskb_pull_tail() dislikes that. If this
occurs, something like the following report will be generated.
kernel BUG at net/core/skbuff.c:1463!
...
RIP: 0010:pskb_expand_head+0x253/0x2b0
...
Call Trace:
__pskb_pull_tail+0x49/0x460
skb_cow_data+0x6f/0x300
rxkad_verify_packet+0x18b/0xb10 [rxrpc]
rxrpc_recvmsg_data.isra.11+0x4a8/0xa10 [rxrpc]
rxrpc_kernel_recv_data+0x126/0x240 [rxrpc]
afs_extract_data+0x51/0x2d0 [kafs]
afs_deliver_fs_fetch_data+0x188/0x400 [kafs]
afs_deliver_to_call+0xac/0x430 [kafs]
afs_wait_for_call_to_complete+0x22f/0x3d0 [kafs]
afs_make_call+0x282/0x3f0 [kafs]
afs_fs_fetch_data+0x164/0x300 [kafs]
afs_fetch_data+0x54/0x130 [kafs]
afs_readpages+0x20d/0x340 [kafs]
read_pages+0x66/0x180
__do_page_cache_readahead+0x188/0x1a0
ondemand_readahead+0x17d/0x2e0
generic_file_read_iter+0x740/0xc10
__vfs_read+0x145/0x1a0
vfs_read+0x8c/0x140
ksys_read+0x4a/0xb0
do_syscall_64+0x43/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by using skb_unshare() instead in the input path for DATA packets
that have a security index != 0. Non-DATA packets don't need in-place
encryption and neither do unencrypted DATA packets.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: Julian Wollrath <jwollrath@web.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Use the previously-added transmit-phase skbuff private flag to simplify the
socket buffer tracing a bit. Which phase the skbuff comes from can now be
divined from the skb rather than having to be guessed from the call state.
We can also reduce the number of rxrpc_skb_trace values by eliminating the
difference between Tx and Rx in the symbols.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a flag in the private data on an skbuff to indicate that this is a
transmission-phase buffer rather than a receive-phase buffer.
Signed-off-by: David Howells <dhowells@redhat.com>
Abstract out rxtx ring cleanup into its own function from its two callers.
This makes it easier to apply the same changes to both.
Signed-off-by: David Howells <dhowells@redhat.com>
Pass the reference held on a DATA skb in the rxrpc input handler into the
Rx ring rather than getting an additional ref for this and then dropping
the original ref at the end.
Signed-off-by: David Howells <dhowells@redhat.com>
Use the information now cached in the skbuff private data to avoid the need
to reparse a jumbo packet. We can find all the subpackets by dead
reckoning, so it's only necessary to note how many there are, whether the
last one is flagged as LAST_PACKET and whether any have the REQUEST_ACK
flag set.
This is necessary as once recvmsg() can see the packet, it can start
modifying it, such as doing in-place decryption.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Improve the information stored about jumbo packets so that we don't need to
reparse them so much later.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Don't manually take rtnl lock in flower classifier before calling cls
hardware offloads API. Instead, pass rtnl lock status via 'rtnl_held'
parameter.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock, modify tc_setup_flow_action()
to copy tunnel info, instead of just saving pointer to tunnel_key action
tunnel info. This is necessary to prevent concurrent action overwrite from
releasing tunnel info while it is being used by rtnl-unlocked driver.
Implement helper tcf_tunnel_info_copy() that is used to copy tunnel info
with all its options to dynamically allocated memory block. Modify
tc_cleanup_flow_action() to free dynamically allocated tunnel info.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock when calling hardware offload
API, take reference to action mirred dev when initializing flow_action
structure in tc_setup_flow_action(). Implement function
tc_cleanup_flow_action(), use it to release the device after hardware
offload API is done using it.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow using new flow_action infrastructure from unlocked
classifiers, modify tc_setup_flow_action() to accept new 'rtnl_held'
argument. Take rtnl lock before accessing tc_action data. This is necessary
to protect from concurrent action replace.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock from offloads code of
classifiers, take rtnl lock conditionally before executing driver
callbacks. Only obtain rtnl lock if block is bound to devices that require
it.
Block bind/unbind code is rtnl-locked and obtains block->cb_lock while
holding rtnl lock. Obtain locks in same order in tc_setup_cb_*() functions
to prevent deadlock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct flow_block_offload with "unlocked_driver_cb" flag to allow
registering and unregistering block hardware offload callbacks that do not
require caller to hold rtnl lock. Extend tcf_block with additional
lockeddevcnt counter that is incremented for each non-unlocked driver
callback attached to device. This counter is necessary to conditionally
obtain rtnl lock before calling hardware callbacks in following patches.
Register mlx5 tc block offload callbacks as "unlocked".
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To remove dependency on rtnl lock, extend classifier ops with new
ops->hw_add() and ops->hw_del() callbacks. Call them from cls API while
holding cb_lock every time filter if successfully added to or deleted from
hardware.
Implement the new API in flower classifier. Use it to manage hw_filters
list under cb_lock protection, instead of relying on rtnl lock to
synchronize with concurrent fl_reoffload() call.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without rtnl lock protection filters can no longer safely manage block
offloads counter themselves. Refactor cls API to protect block offloadcnt
with tcf_block->cb_lock that is already used to protect driver callback
list and nooffloaddevcnt counter. The counter can be modified by concurrent
tasks by new functions that execute block callbacks (which is safe with
previous patch that changed its type to atomic_t), however, block
bind/unbind code that checks the counter value takes cb_lock in write mode
to exclude any concurrent modifications. This approach prevents race
conditions between bind/unbind and callback execution code but allows for
concurrency for tc rule update path.
Move block offload counter, filter in hardware counter and filter flags
management from classifiers into cls hardware offloads API. Make functions
tcf_block_offload_{inc|dec}() and tc_cls_offload_cnt_update() to be cls API
private. Implement following new cls API to be used instead:
tc_setup_cb_add() - non-destructive filter add. If filter that wasn't
already in hardware is successfully offloaded, increment block offloads
counter, set filter in hardware counter and flag. On failure, previously
offloaded filter is considered to be intact and offloads counter is not
decremented.
tc_setup_cb_replace() - destructive filter replace. Release existing
filter block offload counter and reset its in hardware counter and flag.
Set new filter in hardware counter and flag. On failure, previously
offloaded filter is considered to be destroyed and offload counter is
decremented.
tc_setup_cb_destroy() - filter destroy. Unconditionally decrement block
offloads counter.
tc_setup_cb_reoffload() - reoffload filter to single cb. Execute cb() and
call tc_cls_offload_cnt_update() if cb() didn't return an error.
Refactor all offload-capable classifiers to atomically offload filters to
hardware, change block offload counter, and set filter in hardware counter
and flag by means of the new cls API functions.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for running proto ops functions without rtnl lock, change
offload counter type to atomic. This is necessary to allow updating the
counter by multiple concurrent users when offloading filters to hardware
from unlocked classifiers.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock, extend tcf_block with 'cb_lock'
rwsem and use it to protect flow_block->cb_list and related counters from
concurrent modification. The lock is taken in read mode for read-only
traversal of cb_list in tc_setup_cb_call() and write mode in all other
cases. This approach ensures that:
- cb_list is not changed concurrently while filters is being offloaded on
block.
- block->nooffloaddevcnt is checked while holding the lock in read mode,
but is only changed by bind/unbind code when holding the cb_lock in write
mode to prevent concurrent modification.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Dorfman reports that after a series of idle disconnects, an
RPC/RDMA transport becomes unusable (rdma_create_qp returns
-ENOMEM). Problem was tracked down to increasing Send Queue size
after each reconnect.
The rdma_create_qp() API does not promise to leave its @qp_init_attr
parameter unaltered. In fact, some drivers do modify one or more of
its fields. Thus our calls to rdma_create_qp must use a fresh copy
of ib_qp_init_attr each time.
This fix is appropriate for kernels dating back to late 2007, though
it will have to be adapted, as the connect code has changed over the
years.
Reported-by: Eli Dorfman <eli@vastdata.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Ensure that the re-establishment delay does not grow exponentially
on each good reconnect. This probably should have been part of
commit 675dd90ad0 ("xprtrdma: Modernize ops->connect").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the connection breaks while we're waiting for a reply from the
server, then we want to immediately try to reconnect.
Fixes: ec6017d903 ("SUNRPC fix regression in umount of a secure mount")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This reverts commit a79f194aa4.
The mechanism for aborting I/O is racy, since we are not guaranteed that
the request is asleep while we're changing both task->tk_status and
task->tk_action.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v5.1
If a connect or bind attempt returns EADDRINUSE, that means we want to
retry with a different port. It is not a fatal connection error.
Similarly, ENOBUFS is not fatal, but just indicates a memory allocation
issue. Retry after a short delay.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Don't handle errors in call_bind_status()/call_connect_status()
if it turns out that a previous call caused it to succeed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v5.1+
The optimization done in "xprtrdma: Simplify rpcrdma_mr_pop" was a
bit too optimistic. MRs left over after a reconnect still need to
be recycled, not added back to the free list, since they could be
in flight or actually fully registered.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Currently, there is no vlan information (e.g. when used with a vlan aware
bridge) passed to userspache, HWHEADER will contain an 08 00 (ip) suffix
even for tagged ip packets.
Therefore, add an extra netlink attribute that passes the vlan information
to userspace similarly to 15824ab29f for nfqueue.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch introduces meta matches in the kernel for time (a UNIX timestamp),
day (a day of week, represented as an integer between 0-6), and
hour (an hour in the current day, or: number of seconds since midnight).
All values are taken as unsigned 64-bit integers.
The 'time' keyword is internally converted to nanoseconds by nft in
userspace, and hence the timestamp is taken in nanoseconds as well.
Signed-off-by: Ander Juaristi <a@juaristi.eus>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce new helper functions to load/store 64-bit values onto/from
registers:
- nft_reg_store64
- nft_reg_load64
This commit also re-orders all these helpers from smallest to largest
target bit size.
Signed-off-by: Ander Juaristi <a@juaristi.eus>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch addresses a conntrack cache issue with timeout policy.
Currently, we do not check if the timeout extension is set properly in the
cached conntrack entry. Thus, after packet recirculate from conntrack
action, the timeout policy is not applied properly. This patch fixes the
aforementioned issue.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using mpls over gre/gre6 setup, rt->rt_gw4 address is not set, the
same for rt->rt_gw_family. Therefore, when rt->rt_gw_family is checked
in mpls_xmit(), neigh_xmit() call is skipped. As a result, such setup
doesn't work anymore.
This issue was found with LTP mpls03 tests.
Fixes: 1550c17193 ("ipv4: Prepare rtable for IPv6 gateway")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From IB specific 7.6.5 SERVICE LEVEL, Service Level (SL)
is used to identify different flows within an IBA subnet.
It is carried in the local route header of the packet.
Before this commit, run "rds-info -I". The outputs are as
below:
"
RDS IB Connections:
LocalAddr RemoteAddr Tos SL LocalDev RemoteDev
192.2.95.3 192.2.95.1 2 0 fe80::21:28:1a:39 fe80::21:28:10:b9
192.2.95.3 192.2.95.1 1 0 fe80::21:28:1a:39 fe80::21:28:10:b9
192.2.95.3 192.2.95.1 0 0 fe80::21:28:1a:39 fe80::21:28:10:b9
"
After this commit, the output is as below:
"
RDS IB Connections:
LocalAddr RemoteAddr Tos SL LocalDev RemoteDev
192.2.95.3 192.2.95.1 2 2 fe80::21:28:1a:39 fe80::21:28:10:b9
192.2.95.3 192.2.95.1 1 1 fe80::21:28:1a:39 fe80::21:28:10:b9
192.2.95.3 192.2.95.1 0 0 fe80::21:28:1a:39 fe80::21:28:10:b9
"
The commit fe3475af3b ("net: rds: add per rds connection cache
statistics") adds cache_allocs in struct rds_info_rdma_connection
as below:
struct rds_info_rdma_connection {
...
__u32 rdma_mr_max;
__u32 rdma_mr_size;
__u8 tos;
__u32 cache_allocs;
};
The peer struct in rds-tools of struct rds_info_rdma_connection is as
below:
struct rds_info_rdma_connection {
...
uint32_t rdma_mr_max;
uint32_t rdma_mr_size;
uint8_t tos;
uint8_t sl;
uint32_t cache_allocs;
};
The difference between userspace and kernel is the member variable sl.
In the kernel struct, the member variable sl is missing. This will
introduce risks. So it is necessary to use this commit to avoid this risk.
Fixes: fe3475af3b ("net: rds: add per rds connection cache statistics")
CC: Joe Jin <joe.jin@oracle.com>
CC: JUNXIAO_BI <junxiao.bi@oracle.com>
Suggested-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An excerpt from netlink(7) man page,
In multipart messages (multiple nlmsghdr headers with associated payload
in one byte stream) the first and all following headers have the
NLM_F_MULTI flag set, except for the last header which has the type
NLMSG_DONE.
but, after (ee28906) there is a missing NLM_F_MULTI flag in the middle of a
FIB dump. The result is user space applications following above man page
excerpt may get confused and may stop parsing msg believing something went
wrong.
In the golang netlink lib [0] the library logic stops parsing believing the
message is not a multipart message. Found this running Cilium[1] against
net-next while adding a feature to auto-detect routes. I noticed with
multiple route tables we no longer could detect the default routes on net
tree kernels because the library logic was not returning them.
Fix this by handling the fib_dump_info_fnhe() case the same way the
fib_dump_info() handles it by passing the flags argument through the
call chain and adding a flags argument to rt_fill_info().
Tested with Cilium stack and auto-detection of routes works again. Also
annotated libs to dump netlink msgs and inspected NLM_F_MULTI and
NLMSG_DONE flags look correct after this.
Note: In inet_rtm_getroute() pass rt_fill_info() '0' for flags the same
as is done for fib_dump_info() so this looks correct to me.
[0] https://github.com/vishvananda/netlink/
[1] https://github.com/cilium/
Fixes: ee28906fd7 ("ipv4: Dump route exceptions if requested")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If protocols registered exceeded PROTO_INUSE_NR, prot will be
added to proto_list, but no available bit left for prot in
proto_inuse_idx.
Changes since v2:
* Propagate the error code properly
Signed-off-by: zhanglin <zhang.lin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The consume_skb() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In decode_session{4,6} there is a possibility that the skb dst dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv6
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmpv6_send
- icmpv6_route_lookup
- xfrm_decode_session_reverse
- decode_session4
- oif = skb_dst(skb)->dev->ifindex; <-- here
- decode_session6
- oif = skb_dst(skb)->dev->ifindex; <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the skb_dst(skb)->dev is actually not needed as we
called decode_session{4,6} via xfrm_decode_session_reverse(), so oif is not
used by: fl4->flowi4_oif = reverse ? skb->skb_iif : oif;
So make a dst dev check here should be clean and safe.
v4: No changes.
v3: No changes.
v2: fix the issue in decode_session{4,6} instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __icmp_send() there is a possibility that the rt->dst.dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv4
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmp_send
- net = dev_net(rt->dst.dev); <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the reason we need rt->dst.dev is to get the net.
So we can just try get it from skb->dev when rt->dst.dev is NULL.
v4: Julian Anastasov remind skb->dev also could be NULL. We'd better
still use dst.dev and do a check to avoid crash.
v3: No changes.
v2: fix the issue in __icmp_send() instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: c8b34e680a ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2019-08-24
An update from ieee802154 for your *net* tree.
Yue Haibing fixed two bugs discovered by KASAN in the hwsim driver for
ieee802154 and Colin Ian King cleaned up a redundant variable assignment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-08-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix verifier precision tracking with BPF-to-BPF calls, from Alexei.
2) Fix a use-after-free in prog symbol exposure, from Daniel.
3) Several s390x JIT fixes plus BE related fixes in BPF kselftests, from Ilya.
4) Fix memory leak by unpinning XDP umem pages in error path, from Ivan.
5) Fix a potential use-after-free on flow dissector detach, from Jakub.
6) Fix bpftool to close prog fd after showing metadata, from Quentin.
7) BPF kselftest config and TEST_PROGS_EXTENDED fixes, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
test_select_reuseport fails on s390 due to verifier rejecting
test_select_reuseport_kern.o with the following message:
; data_check.eth_protocol = reuse_md->eth_protocol;
18: (69) r1 = *(u16 *)(r6 +22)
invalid bpf_context access off=22 size=2
This is because on big-endian machines casts from __u32 to __u16 are
generated by referencing the respective variable as __u16 with an offset
of 2 (as opposed to 0 on little-endian machines).
The verifier already has all the infrastructure in place to allow such
accesses, it's just that they are not explicitly enabled for
eth_protocol field. Enable them for eth_protocol field by using
bpf_ctx_range instead of offsetof.
Ditto for ip_protocol, bind_inany and len, since they already allow
narrowing, and the same problem can arise when working with them.
Fixes: 2dbb9b9e6d ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Call to bpf_prog_put(), with help of call_rcu(), queues an RCU-callback to
free the program once a grace period has elapsed. The callback can run
together with new RCU readers that started after the last grace period.
New RCU readers can potentially see the "old" to-be-freed or already-freed
pointer to the program object before the RCU update-side NULLs it.
Reorder the operations so that the RCU update-side resets the protected
pointer before the end of the grace period after which the program will be
freed.
Fixes: d58e468b11 ("flow_dissector: implements flow dissector BPF hook")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Petar Penkov <ppenkov@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Timestamps are currently communicated to user space as 'struct
timespec', which is not considered y2038 safe since it uses a 32-bit
signed value for seconds.
Fix this while the API is still not part of any official kernel release
by using 64-bit nanoseconds timestamps instead.
Fixes: ca30707dee ("drop_monitor: Add packet alert mode")
Fixes: 5e58109b1e ("drop_monitor: Add support for packet alert mode for hardware drops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RDMA cookie and RX timestamp to the usercopy whitelist.
After the introduction of hardened usercopy whitelisting
(https://lwn.net/Articles/727322/), a warning is displayed when the
RDMA cookie or RX timestamp is copied to userspace:
kernel: WARNING: CPU: 3 PID: 5750 at
mm/usercopy.c:81 usercopy_warn+0x8e/0xa6
[...]
kernel: Call Trace:
kernel: __check_heap_object+0xb8/0x11b
kernel: __check_object_size+0xe3/0x1bc
kernel: put_cmsg+0x95/0x115
kernel: rds_recvmsg+0x43d/0x620 [rds]
kernel: sock_recvmsg+0x43/0x4a
kernel: ___sys_recvmsg+0xda/0x1e6
kernel: ? __handle_mm_fault+0xcae/0xf79
kernel: __sys_recvmsg+0x51/0x8a
kernel: SyS_recvmsg+0x12/0x1c
kernel: do_syscall_64+0x79/0x1ae
When the whitelisting feature was introduced, the memory for the RDMA
cookie and RX timestamp in RDS was not added to the whitelist, causing
the warning above.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Tested-by: Jenny <jenny.x.xu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ipv6_find_idev returns NULL when ipv6_add_dev fails,
ignoring the specific error value. This results in addrconf_add_dev
returning ENOBUFS in all cases, which is unfortunate in cases such as:
# ip link add dummyX type dummy
# ip link set dummyX mtu 1200 up
# ip addr add 2000::/64 dev dummyX
RTNETLINK answers: No buffer space available
Commit a317a2f19d ("ipv6: fail early when creating netdev named all
or default") introduced error returns in ipv6_add_dev. Before that,
that function would simply return NULL for all failures.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple batadv_ogm2_packet can be stored in an skbuff. The functions
batadv_v_ogm_send_to_if() uses batadv_v_ogm_aggr_packet() to check if there
is another additional batadv_ogm2_packet in the skb or not before they
continue processing the packet.
The length for such an OGM2 is BATADV_OGM2_HLEN +
batadv_ogm2_packet->tvlv_len. The check must first check that at least
BATADV_OGM2_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Multiple batadv_ogm_packet can be stored in an skbuff. The functions
batadv_iv_ogm_send_to_if()/batadv_iv_ogm_receive() use
batadv_iv_ogm_aggr_packet() to check if there is another additional
batadv_ogm_packet in the skb or not before they continue processing the
packet.
The length for such an OGM is BATADV_OGM_HLEN +
batadv_ogm_packet->tvlv_len. The check must first check that at least
BATADV_OGM_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Reported-by: syzbot+355cab184197dbbfa384@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
zhong jiang