* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list. This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path. However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a deadlock between child interface creation/deletion and ipoib
start/stop. The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev(). The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.
Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL. We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().
Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.
Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add dependency on INFINIBAND_ADDR_TRANS
IPoIB: Do not join broadcast group if interface is brought down
RDMA/nes: Fix for NIPQUAD removal
IPoIB: Fix loss of connectivity after bonding failover on both sides
IB/mlx4: Don't register IB device for adapters with no IB ports
mlx4_core: Fix warning from min()
IB/ehca: spin_lock_irqsave() takes an unsigned long
Fix ib_iser build to depend on INFINIBAND_ADDR_TRANS; if INET=y but
IPV6=n, then the RDMA CM is not built but INFINIBAND_ISER can be
enabled, leading to:
ERROR: "rdma_destroy_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_connect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_destroy_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_route" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_disconnect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_addr" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup). This
will cause the system to be a member of the broadcast group when
interface is down. As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost. In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first. When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists. It will not have an AH
either, because of sender-side failover. Therefore, it will not get
an AH when the path is resolved.
The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid. Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iSCSI/iSER targets may send PDUs without a prior request from the
initiator. RFC 5046 refers to these PDUs as "unexpected". NOP-In PDUs
with itt=RESERVED and Asynchronous Message PDUs occupy this category.
The amount of active "unexpected" PDU's an iSER target may have at any
time is governed by the MaxOutstandingUnexpectedPDUs key, which is not
yet supported.
Currently when an iSER target sends an "unexpected" PDU, the
initiators recv buffer consumed by the PDU is not replaced. If over
initial_post_recv_bufs_num "unexpected" PDUs are received then the
receive queue will run out of receive work requests entirely.
This patch ensures recv buffers consumed by "unexpected" PDUs are
replaced in the next iser_post_receive_control() call.
Signed-off-by: David Disseldorp <ddiss@sgi.com>
Signed-off-by: Ken Sandars <ksandars@sgi.com>
Acked-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of IPOIB_GID_FMT, IPOIB_GID_RAW_ARG() and IPOIB_GID_ARG()
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds