This patch adds a new device-tree property that allows to
specify the dma protection control bits for the all of the
DMA controller's channel uniformly.
Setting the "correct" bits can have a huge impact on the
PPC460EX and APM82181 that use this DMA engine in combination
with a DesignWare' SATA-II core (sata_dwc_460ex driver).
In the OpenWrt Forum, the user takimata reported that:
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Another user And.short reported:
|I can report that your fix worked! Boots up fine with two
|drives even with more partitions, and no more reboot on
|concurrent disk access!
A closer look into the sata_dwc_460ex code revealed that
the driver did initally set the correct protection control
bits. However, this feature was lost when the sata_dwc_460ex
driver was converted to the generic DMA driver framework.
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/55
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/50
Fixes: 8b3444852a ("sata_dwc_460ex: move to generic DMA driver")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The integrated DMA (iDMA 32-bit) is Intel designed DMA controller which
mimics Synopsys Designware DMA. This patch appends the register mappings
for the parts which are slightly different to the DesignWare hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly introduced helpers prepare driver to support new DMA controller
hardware.
While here, introduce DWC_CTLH_BLOCK_TS() macro as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It seems we need to extend custom slave configuration by one more member to
support Intel Quart UART. It becomes a burden to manage all members of struct
dw_dma_slave one-by-one.
Replace the set of fields by embedding struct dw_dma_slave into struct
dw_dma_chan.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the entire platform data in the struct dw_dma.
It makes the driver a bit cleaner.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch changes the driver to allocate DMA descriptors when
needed. This stops memory resources to be wasted and letting
them sit idle in the free_list structure when the device doesn't
need it... This also solves the problem, that a driver has to
guess the number of how many descriptors it needs to allocate
in advance. Currently, the dma engine will just fail when put
under load by sata_dwc_460ex.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Residue is a property of any active descriptor. So, any descriptor may be in
different state but residue is a feature of active descriptor. Check if the
asked descriptor is active and return proper residue value for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Covert dwc->initialized to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Convert dwc->paused to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since struct dw_dma is allocated and regs member is assigned properly we can
use standard IO accessors to the DMA registers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LMS field indicates from which master the descriptor is to be
read. This patch assumes this is always the same as the memory
side in a peripheral transfer which is true for all known systems.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the DMA controller uses a different byte order than the host CPU,
the hardware linked list descriptor fields need to be byte-swapped.
This patch makes the driver write these fields using the same byte
order it uses for mmio accesses to the DMA engine. I do not know
if this is guaranteed to always be correct.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The offset of SINC should be 9, not 7, here fix this
typo.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable controller automatically whenever first user requires for a channel and
disable it when the last user gone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we don't allow user to set registers directly through private slave
configuration we may move definitions to the regs.h because they are not used
anywhere except core.c part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On BayTrail platform DMA is not functional in the PCI mode, whereby it always
failed and exit at the point when it tries to get a clock. It causes the PCI
mode probe to exit with the error message:
dw_dmac_pci: probe of 0000:00:1e.0 failed with error -2
This patch moves clock operations to where it belongs to. Thus, the clock is
provided only in ACPI / non-PCI cases.
Reported-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of one request line member let's use both source and destination ones.
Usually we have no such hardware except Atmel MMC controller found on AVR32
platform (see arch/avr32/mach-at32ap/at32ap700x.c and
drivers/mmc/host/atmel-mci.c).
This patch removes slave_id usage since it'll be removed from the generic
structure in later. This breaks the non-ACPI / non-DT cases for the users of
the driver, i.e. SPI and HSUART. However, these cases mean only PCI enumerated
devices for now, which is anyway broken (considering more than one DMA
controller in the system) and this patch series is intended to fix that
eventually.
The ACPI and DT cases shall be aware of the channel direction when setting
request lines, but this is a minor problem that would be addressed in future.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a common storage for platform data related structures and definitions
inside kernel source tree. The patch moves file from include/linux to
include/linux/platform_data and renames it acoordingly. The users are also
updated.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[For the arch/avr32/.* and .*sound/atmel.*]
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This makes the probe() function a little bit clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To simplify the driver development let's split driver to library and platform
code parts. It helps us to add PCI driver in future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[Fixed compile error and few checkpatch issues]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Christian Lamparter