Previous init path was based on old specs from old driver. Update it
as much as possible leaving some TODOs for not implemented functions.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move table init to tables_nphy.c, detect newer PHY which use different init.
We don't init newer PHYs yet but this at least shows what more is needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following line shows my BCM4328 detected on SSB. We didn't include 0x0C rev.
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0C, vendor 0x4243)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously ath9k left the initialization of slot timing and ACK/CTS
timeout to the mode specific initvals. This does not handle short vs
long slot in 2.4 GHz and uses a rather strange value for the 2.4 GHz
ACK timeout (64 usec).
This patch uses the proper ath9k_hw functions for setting slot time and
timeouts and also implements the switch between short and long slot
time in 2.4 GHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be marked as invalid before
registering the ISR. HW initialization takes place
after the ISR has been registered, and the invalid
flag is eventually cleared in the ->stop() callback.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In f41f3f373d the B43 driver was ported
to use the cfg80211 API for rfkill and consequently the config option
was dropped (RFKILL is now unconditionally enabled).
However in the Kernel Info the feature is still checked and reported
missing. This patch just removes the conditional and the relevant code
blocks while still reporting that feature unconditionally would be
another option (it's always there).
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are unused and as with a previous patch 5ef5da for wl1251
this removes some other unused flags. the IRQ_MASK specifically
conflicts with include/pcmcia/cs.h when using compat-wireless.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance module information with the names of the firmware files
that could be used by this driver. This helps tools like Jockey to
correctly detect and/or install the firmware files relevant to
this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/488636
Enhances module information with the names of the firmware files
that could be used by this driver. This helps tools like Jockey to
correctly detect and/or install the firmware files relevant to
this driver.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this header, we can trigger a UMAC crash with debug enabled UMACs.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 6c853da3f3.
From Message-ID: <1262663293.551.117.camel@debian>
On Sat, 2010-01-02 at 22:09 +0800, Dan Carpenter wrote:
> It don't think 6c853da3f3 is right. That's the patch
> titled "iwmc3200wifi: fix array out-of-boundary access"
>
> Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
> index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
>
> In 2.6.33-rc2 IWM_RX_ID_GET_HASH() doesn't go as high as IWM_RX_ID_HASH
> and I don't see any array out-of-bounds.
>
> #define IWM_RX_ID_GET_HASH(id) ((id) % IWM_RX_ID_HASH)
Ah, you are right. I took '%' for '&'. John, would you revert it? Sorry
for the false alarm.
Thanks,
-yi
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As follows:
- GET_HW_SPEC is now responsible for setting
priv->{ap,sta}_macids_supported, which are bitmasks of supported
macids for AP and STA mode. (Typically, STA firmware images will
support only one macid, #0, in STA mode, and AP firmware images
will support macids #0-7, in AP mode.)
- Our wiphy ->interfaces_modes is now set based on the non-zero-ness
of these two bitmasks.
- We main priv->macids_used, a bitmask of which macids are currently
in use. ->add_interface() will assign the lowest free macid for
this interface type as it is created, or bail out if there are no
more free macids to assign. ->delete_interface() will mark the
macid as being free again.
This enables the multi-BSS code added in the previous commits.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SET_BEACON, SET_MAC_ADDR, BSS_START and SET_NEW_STN are the currently
supported firmware commands that are actually per-vif commands. Use
mwl8k_post_pervif_cmd() for these commands, so that the macid of the
vif they operate on gets passed down into the firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the bytes in the mwl8k firmware command header is the 'macid'
byte, which for per-vif commands indicates which of the BSSes this
command is intended for. (For commands that are not per-vif commands,
this byte can just be 0.)
This patch adds mwl8k_post_pervif_cmd(), which will take the macid
assigned to this interface (to be done in ->add_interface()), copy it
into the command packet macid field, and post the command as usual.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding multi-BSS support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the decision about whether to register the 2.4 and 5 GHz bands
with mac80211 by looking at the capability field in GET_HW_SPEC (STA
firmware only for now). This enables 5 GHz STA operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever mac80211 gives us a legacy rate bitmap in the context of the
5 GHz band, we need to remember to shift the bitmap left by 5 positions
before giving it to the firmware, as the firmware follows the bitmap
bit assignment of the 2.4 GHz rate table even if we're on the 5 GHz
band, and the 2.4 GHz rate table includes five non-OFDM rates at the
start that are not valid in the 5 GHz band.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mwl8k firmware uses indices into the 2.4 GHz band rate table for
the receive descriptor channel field even if the packet was received
on a 5 GHz channel, while mac80211 expects an index into the 5 GHz
band rate table when packets are received on the 5 GHz band, which
presents a mismatch as the 5 GHz band rate table lacks the five
non-OFDM rates that the 2.4 GHz rate table starts with.
To handle this properly, we need to substract 5 from the rate index
field if the packet was received on a 5 GHz channel (and was not
received at an MCS rate).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that we can make 2.4 GHz and 5 GHz band registration conditional
on the capability bitmask returned by the firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding 5 GHz band/channels/rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0x2a43 is a single-band (2.4GHz only) 88w8366 mini-PCIe card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By storing the sequence counter in << 4 format, like other drivers do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add MODULE_FIRMWARE tags for the mwl8k firmware images that don't
have them yet, and move them to where the firmware image names are
declared.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 firmware supports U-APSD just with a simple queue configuration
change so enable it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qos null data template is needed for U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
void pointers do not need to be cast to other pointer types.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting invalid byte count in txq byte count table, read pointer
should be used instead of write pointer.
Reported-by: Guo, Chaohong <chaohong.guo@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"RADAR_NOTIFICATION" host command is not used and not supported by uCode,
remove it from driver code.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update data structure to match latest statistics report from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 do not check the return code now, what if mac80211 does start
using the return code? IEEE80211_AMPDU_TX_OPERATIONAL is a valid action,
just iwlwifi driver do not need to take any action for it; so instead of
return "-EINVAL", it is a good program practice to return "-EOPNOTSUPP"
to make sure mac80211 will not get wrong impression.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like how TX reclaim is done in a tasklet, move receive processing
to tasklet context as well. This can have nice benefits for CPU
utilisation and throughput, especially at 3-stream rates.
(Use the same CLEAR_SEL trick as the TX reclaim tasklet does, to
avoid having to touch the interrupt mask registers.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By making use of the CLEAR_SEL feature of the mwl8k host interface
interrupt controller, we can keep the TX_DONE interrupt source masked
while the transmit reclaim tasklet is running (NAPI style) without
having to touch the interrupt controller's interrupt mask register
when entering or exiting polling mode, and without having to do any
more register reads/writes than we do now.
When CLEAR_SEL is enabled on the TX_DONE interrupt source, reading
the interrupt status register will clear the TX_DONE status bit if
it was set, allowing it to be set again if a new TX_DONE event arrives
while we are running the TX reclaim tasklet, but such a new event will
then not trigger another PCI interrupt until a zero is written to the
TX_DONE interrupt status register bit.
I.e., if we write a zero to the TX_DONE interrupt source bit in the
interrupt status register when the TX reclaim tasklet thinks it's
done, a PCI interrupt will be triggered if a new TX_DONE event arrived
from the hardware between us deciding that there is no more work to do
and re-enabling the TX_DONE interrupt source, thereby avoiding the
classic NAPI poll mode exit race that would otherwise occur.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a limit argument to mwl8k_txq_reclaim(), to allow limiting the
number of packets that it will reclaim, and make it return the number
of packets that it reclaimed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for creating AP interfaces, and enabling beaconing.
This allows running a basic AP (11b/g mode only for now).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
STA firmware uses UPDATE_STADB to manipulate the hardware station
database, whereas AP firmware uses SET_NEW_STN -- this implements the
latter, and hooks it into mwl8k_sta_notify(), to be used if we're
running on AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As with the STA version, unicast will use auto rate adaptation, but
the AP version allows setting the rates to be used for management and
multicast transmissions, which can be set based on the BSS basic rate
set.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we always use the auto rate adaptation feature and never pass in
a rate table, USE_FIXED_RATE can be simplified somewhat. While we're
at it, rename it to *_sta, as this is the STA version of the command.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While it is reasonable to expect that at least one transmit ring entry
will be processed per second while we are waiting for the transmit
rings to drain, the firmware can end up doing batching of transmit ring
status writeback, which means that the transmit rings can appear stuck
for more than a second at a time.
Bump the TX drain wait timeout up from 1 to 5 seconds to account for
this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment and code in mwl8k_cmd_set_edca_params() suggest that the
mapping between SET_EDCA_PARAMS queue numbers and transmit rings isn't
actually 1:1, while tests show that the mapping is in fact 1:1. So,
get rid of the transmit queue 0/1 swapping.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 passes appropriate flags indicating whether
monitor mode is being used. Use this to set the HW opmode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file can be used to track frame reception errors.
PHY error counts are also added.
Location: ath9k/phy#/recv
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX queues have to be stopped during an
internal reset. Not handling this would result
in packet loss - fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device initialization and termination functions
were messy and convoluted. Introduce helper functions
to clarify init_softc() and simplify things in general.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_flags has slowly become a kitchen sink over time.
Move powersave related flags to a separate variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In various cases wl1251_op_bss_info_changed() did not call elp_sleep()
after an error was noticed. Fix it by using correct goto label.
The bug was a theoretical one, in practise it doesn't matter because
if commands start returning errors there will be lots of other problems.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of channels to be used in scan was hard coded in wl1251. The
proper way is to use the channels array provided by mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of creating the template in driver, get it from mac80211 instead.
Thanks to this, three functions can be now removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current scanning code wasn't following the preferred style. Move code
related to scan and trigger scan to commans to wl1251_cmd.c. Because
there's now less code in wl1251_hw_scan(), the function can be now
merged with wl1251_op_hw_scan().
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that mac80211 creates templates for PS Poll and Nullfunc frames, use
them instead of creating our own.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used within the rt2800lib module itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800pci_wait_wpdma_ready and rt2800usb_wait_wpdma_ready functions are
exactly the same, so unify them into rt200lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RF3052 chipset is now also being integrated onto USB devices, so
allow the RF chipset and don't treat it as PCI/SOC only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback sets slot time as specified in IEEE 802.11-2007 section
17.3.8.6 (for 20MHz channels only for now) and raises ACK and CTS
timeouts accordingly. The values are persistent, they are restored after
device reset.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was correct in 802.11a mode only, 802.11b/g uses
different clock rates. The new code uses values taken from FreeBSD HAL
and should be correct for all modes including turbo modes.
The former rate calculation was used by slope coefficient calculation
function ath5k_hw_write_ofdm_timings. However, this function requires
the 802.11a values even in 802.11g mode. Thus the use of
ath5k_hw_htoclock was replaced by hardcoded values. Possibly the slope
coefficient calculation is not related to clock rate at all.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions ath5k_hw_get_slot_time and ath5k_hw_set_slot_time were
converting microseconds to clocks only for AR5210, although it's needed
for all supported devices. The conversion was moved outside the
hardware-specific branches.
The original code also limited minimum slot time to 9, while turbo modes
use 6, this was fixed too.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: stable@kernel.org
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is
past the end of the array. In the resulting discussion, Zhu Yi pointed out
that this value is not used in real life and the assignment was only there to
silence a gcc warning.
If there were a bug in the surrounding code and the value were used, the
WARN_ON(!qc) would print a warning before the crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.
Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.
Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables HT association and AMPDU in the receive direction for
STA firmware images on hardware that supports it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU receive doesn't need any special handling, so let's enable
this before tackling the transmit side.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the AP's MCS rate mask to SET_RATE when associating, and make
UPDATE_STADB pass in the peer's HT caps and rates when adding a new
hardware station database entry.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mwl8k_bss_info_changed() would refuse to do anything if
the 'changed' argument indicated that the association status hadn't
changed. Fix this up so that it will allow changing things like the
preamble type, the slot time and the CTS-to-self protection method
without having to reassociate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling SET_RATE, SET_AID, or when creating a station database
entry for our AP, pass in the AP's rate set instead of just blindly
enabling all legacy rates, so as to end up doing the right thing when
talking to 11b-only APs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA firmware, move the per-peer hardware station ID to the
driver-private part of struct ieee80211_sta, where it belongs.
(Since issuing a hardware station database maintenance command sleeps,
we can't hold a reference to the ieee80211_sta * across the command,
and since we won't know the station ID until after the command
completes, we need to re-lookup the sta when the command is done to
write the returned station ID back to its driver-private part.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inserting and removing a hardware station database entry for the AP
when we are in managed mode is currently done in ->bss_info_changed().
To prepare for adding AP mode support, implement the ->sta_notify()
driver method, and let that handle inserting and removing the hardware
station database entry for our AP instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 250cce26d5 uses UTS_RELEASE
as the the in-tree iwlwifi driver version. However the inclusion
of generated/utsrelease.h makes it a unpleasant behaviour to
recompile the driver everytime when utsrelease.h is updated. In
fact, the driver module is already built with the UTS_RELEASE
information via vermagic of modinfo. Mark the in-tree driver
with the version string "in-tree" to distinguish with those old
out-of-tree drivers.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rt2x00 drivers may result in a "ieee80211_tx_status: headroom too
small" error message when a frame needs to be properly aligned before
transmitting it.
This is because the space needed to ensure proper alignment isn't
requested from mac80211.
Fix this by adding sufficient amount of alignment space to the amount
of headroom requested for TX frames.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_blink_set uses an illegal value to set the LED_CFG_G_LED_MODE
field of the LED_CFG register. This field is only 2 bits large, so
should be initialized with value that fits. Use default value from
the vendor driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2x00dev->ops->extra_tx_headroom, not rt2x00dev->hw->extra_tx_headroom
in the tx code, as the later may include other headroom not to be used in
the chipset driver.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 8bf3d79bc401ca417ccf9fc076d3295d1a71dbf5 enabled EEPROM
checksum checks to avoid bogus bug reports but failed to address
updating the code to consider devices with custom EEPROM sizes.
Devices with custom sized EEPROMs have the upper limit size stuffed
in the EEPROM. Use this as the upper limit instead of the static
default size. In case of a checksum error also provide back the
max size and whether or not this was the default size or a custom
one. If the EEPROM is busted we add a failsafe check to ensure
we don't loop forever or try to read bogus areas of hardware.
This closes bug 14874
http://bugzilla.kernel.org/show_bug.cgi?id=14874
Cc: stable@kernel.org
Cc: David Quan <david.quan@atheros.com>
Cc: Stephen Beahm <stephenbeahm@comcast.net>
Reported-by: Joshua Covington <joshuacov@googlemail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If multicast parameter (as returned by zd_op_prepare_multicast) has
changed, no bit in changed_flags is set. To handle this situation, we do
not return if changed_flags is 0. If we do so, we will have some issue
with IPv6 which uses multicast for link layer address resolution.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tid is used as an array offset.
agg = &priv->stations[sta_id].tid[tid].agg;
iwl4965_tx_status_reply_tx(priv, agg, tx_resp, txq_id, index);
It should be limitted to MAX_TID_COUNT - 1;
struct iwl_tid_data tid[MAX_TID_COUNT];
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was an error acquiring the firmware lock in
mwl8k_configure_filter(), we would end up leaking the multicast
command packet prepared by mwl8k_prepare_multicast().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of sizeof() is byte instead of bit, so fix it.
The patch can fix debug output of some dma_addr_t variables.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing DEBUG_FS dependency for ATH9K_DEBUGFS in ath9k's Kconfig.
Signed-off-by: Dominik D. Geyer <dominik.geyer@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a timeout bug in
/drivers/net/wireless/wl12xx/wl1271_spi.c
In the current code you cannot tell why you exited
the "poll for data ready" do-while loop if exiting
was done after the last possible loop.
Then timeout==0 regardless of (val & OCP_READY_MASK) or
!(val & OCP_READY_MASK), leading to possible false timeout...
Simple correction could be decreasing timeout after checking
for !(val & OCP_READY_MASK), not before
(Manually converted from email to an actual patch by me. -- JWL)
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
* before scanning sends the nullfunc frames
* after scanning sends the nullfunc frames, if any
* when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is checked in add_interface, but there it is easily replaced with
a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above. Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only checked in add_interface, and there it is easily replaced
with a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need for Kconfig symbols RT2800PCI_PCI and RT2800PCI_SOC to be
tristates, as they are only used to check whether RT2800 PCI or SOC support
is to be compiled in.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib currently checks whether RT2800USB is enabled in the configuration.
Strictly speaking this is not necessary, it only needs to know whether the
generic rt2x00usb library functions are available. Therefore check for
RT2X00_LIB_USB instead.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix checking for SOC support in rt2800pci. The wrong config (an unexisting
one) was checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.
Add checking for the vif.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the data path configuration, one of the parameters is the channel. We
have been setting it to wl->channel, which is not correct in this case. This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase. Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the new reference driver, some of the firmware configuration values have
been changed. This patch changes them in the wl1271 driver accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use 0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.
Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use. Therefore, move
rx/tx ring initialisation to be after firmware loading.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous change added in:
commit 815833e7ec
ath9k: fix tx status reporting
was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.
This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.
Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the TX hang monitoring routine when doing a scan.
Monitoring for a hung situation is not really necessary during
a scan run.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cancel/restart the ANI timer directly.
With this patch, the ANI lock can be removed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k currently supports only RX interrupt
mitigation.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard-coding the SM PS mode per hardware,
this makes iwlwifi support the new mac80211 API for
controlling the SM PS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw always assumed that the storage device is at endpoint 1,
but there are devices (Spairon Homelink 1202) that are at endpoint 0.
Try both, starting with 1 to make sure to not break existing setups.
Signed-off-by: Stefan Seyfried <seife@sphairon.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since mac80211_hwsim supports multiple virtual interfaces, we need to
iterate through all active interfaces when figuring out whether there
is a match during TX Ack status checking. This fixes TX status
reporting for cases where secondary interfaces are used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Determine the offset at compile time.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable was once set to WLAN_CAPABILITY_SHORT_PREAMBLE and
there's no code that could change the variable to something else.
Therefore it seems this is not necessary :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly for the embedded people that know beforehand that they don't need
MESH at all and want to save some bytes, but also helpful for the upcoming
cfg80211 transition.
text data bss dec hex filename
114264 2308 140 116712 1c7e8 libertas.ko with mesh
105026 2000 140 107166 1a29e libertas.ko without mesh
--------------------------------------------------
-9238 -308 -9546
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While it's might be technically true that only MESH-enabled firmwares
are also RTAP-enabled, I like to have this decoupled.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_autostart_enabled was nowhere set. Rumor is that this is used in the
OLPC tree, but they never did submit their code upstream.
After removing this code, it turned out that the sync_channel stuff is now
also unused, so get rid of that as well.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both variables contained the same information (no mesh, old mesh, new mesh).
So we can get rid of one variable.
Also move the mesh-version test from cmd.c into mesh.c.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not that we actually ever aggregate anything, but
it could potentially be useful anyhow to simulate
aggregation sessions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the device receives an A-MSDU frame (indicated by flag
IWM_RX_TICKET_AMSDU_MSK), use ieee80211_amsdu_to_8023s to convert
it to a list of 802.3 frames and handled them to upper layer.
Cc: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that frames without payload are properly trimmed in
rt2x00queue_insert_l2pad.
This should fix the bug reported by Benoit Papillault in:
http://marc.info/?l=linux-wireless&m=125974773006734&w=2
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Ralink source code, the RX frame format is RXINFO + RXWI +
802.11 frame + RXD, including various padding. Before this patch, we
were using RXD + RXWI + 802.11 frame, so RXD was not correct.
Doing this, we fix the L2PAD bit which is now correctly set on received
frames.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX aggregation is a way to receive multiple 802.11 frames in one RX buffer.
However, we don't know yet how to handle this case in rt2800usb_fill_rxdone
and this has probably no impact on RX performance as well, so we disable it
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
L2 padding will only be present when there is actual payload present.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the rt2x00queue_insert_l2pad function by handling the alignment
operations one by one. Do not special case special circumstances.
Basically first perform header alignment, and then perform payload alignment
(if any payload does exist). This results in a properly aligned skb.
The end result is better readable code, with better results, as now L2 padding
is inserted only when a payload is actually present in the frame.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the improved L2 padding code, this flag is no longer necessary, as the
rt2x00queue_remove_l2pad is capable of detecting by itself if L2 padding is
applied.
For received frames the RX descriptor flag is still being checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a couple of more bugs in the L2 padding code:
1. Compute the amount of L2 padding correctly (in 3 places).
2. Trim the skb correctly when the L2 padding has been applied.
Also introduce a central macro the compute the L2 padding size.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise we end up truncating the skb before removing the l2pad
thus we might have the truncated part become garbage while getting
it back in remove_l2pad.
For the same issue: remove the skb_trim from the rt2800 fill_rxdone
(it is done after l2pad removal in rt2x00lib_rxdone).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not include timestamp for a frame that has been injected
through a monitor interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The padding is to be added between header and payload for the only header need
padding case.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
platform rfkill is async thus we may try to read while the device is
already off.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kenichi HORIO <moattailk1@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not need to log error when fail the sensitivity command, driver will send
sensitivity write command to uCode after each sensitivity calibration if
station is associated with AP. It is a normal case when user unload the module
or shutdown the system while still associated with the AP, since uCode already
on the way down, it will not reply the sensitivity write request; report
error in this case will give misleading information, remove the error checking
here to provide a clean shutdown if no other error detected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables the on-screen uCode event log dump. The original
method will append the event log to syslog; with this capability,
we also enable the user to write script to capture the
events which provide additional flexibility to help uCode debugging
Method
1) change to debugfs directory (sys/kernel/debug/phyX/iwlagn/data)
2) #cat log_event
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to help uCode debugging, adding the capability to provide
continuous uCode event logging function.
uCode events is located in round-robin event queue and filled by uCode,
by enable continuous event logging, driver check the write pointer
and log the newly added events in iwl_bg_ucode_trace() timer function.
There is still possibility of missing events if event queue being
wrapped before next event dump; but with this capability, we can have
much better understanding of the uCode behavior during runtime; it can
help to debug the uCode related issues.
Methods to enable/disable the continuous event log:
step 1: enable ucode trace timer
"echo 1 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
step 2: start ftrace
sudo ./trace-cmd record -e iwlwifi_ucode:* sleep 1d
step 3: stop ftrace
sudo ./trace-cmd report trace.dat
step 4: disable ucode trace timer
"echo 0 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
use "ucode_tracing" debugfs file to display number of event
queue wrapped when driver attempt the continuous event logging. If event
queue being wrapped more than once when driver has opportunity to log
the event; it indicated there are events missing in the event log trace.
This continuous event log function only available for 4965 and newer
NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode HW/SW error detected, dumping important CSR (Control and Status
Registers) values.
Also add "csr" debugfs file to dump the current values of CSR defined in
CSR table to syslog.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change name from RF_CARD_DISABLED to CT_CARD_DISABLED to match the
indication from uCode, also log the debug message when the condition
detected in iwl_rx_card_state_notif()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building rtl8180, the following warning occurs:
CC [M] drivers/net/wireless/rtl818x/rtl8180_dev.o
drivers/net/wireless/rtl818x/rtl8180_dev.c: In function ‘rtl8180_handle_rx’:
drivers/net/wireless/rtl818x/rtl8180_dev.c:135: warning: ‘qual’ is deprecated
(declared at include/net/mac80211.h:562)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't copy module parameters for bcm4320a to private structure.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before transmission when aligning the buffer to 4-byte bounday, tx_hdr
needs to be updated. Otherwise debug logs print false data.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wakeup time calculation was too complicated, simplify it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This debug message was missing and caused incomplete log messages.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when debugging the state is good info.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a rather embarrassing typo.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch aggregates a bunch of small random changes
that won't fit really anywhere else properly.
1. move tid-locating macro into a separate function.
2. remove redundant NULL check.
3. add modulation mask definition
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flags in question were once useful for debugging.
Time has passed and now they do nothing more than
duplicating txinfo->flags.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170 has the bad habit of choking when traffic builds up.
Tests have shown that this can partially be attributed to
a huge buildup of backlogged frames.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes dead infrastructure which was meant
for an out-of-tree rate control algorithm.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: https://bugs.launchpad.net/ubuntu/+bug/254837
Spurious shared interrupts or early probing interrupts can cause the
hostap interrupt handler to oops before the driver has fully configured
the IO base port addresses. In some cases the oops can be because
the hardware shares an interrupt line, on other cases it is due to a
race condition between probing for the hardware and configuring
the IO base port. The latter occurs because the probing is required to
determin the hardware port address which is only determined when the probe
can interrupt the hardware (catch 22).
This patch catches this pre-configured condition to avoid the oops.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The option to support the old style PSK interface in the PS3
GELIC wireless drivers requires CONFIG_WEXT_PRIV to be set
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`queue' was unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver copies the SSID buffer back to the wireless core and
appends a trailing NULL character for termination. This is
a) unnecessary because the buffer is allocated with kzalloc and is hence
already NULLed when this function is called, and
b) for priv->curbssparams.ssid_len == 32, it writes back one byte too
much which causes memory corruptions.
Fix this by removing the extra write.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Maithili Hinge <maithili@marvell.com>
Cc: Kiran Divekar <dkiran@marvell.com>
Cc: Michael Hirsch <m.hirsch@raumfeld.com>
Cc: netdev@vger.kernel.org
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@lists.infradead.org
Cc: stable@kernel.org
Acked-by: Holger Schurig <holgerschurig@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal, driver-specific maintenance of sequence
numbers is applicable only for HT frames.
Also, remove comments that are not relevant anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki