Right now we run through the errata workarounds check on all boot
active CPUs, with SCOPE_ALL. This wouldn't help for detecting erratum
workarounds with a SYSTEM_SCOPE. There are none yet, but we plan to
introduce some: let us clean this up so that such workarounds can be
detected and enabled correctly.
So, we run the checks with SCOPE_LOCAL_CPU on all CPUs and SCOPE_SYSTEM
checks are run only once after all the boot time CPUs are active.
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We are about to group the handling of all capabilities (features
and errata workarounds). This patch open codes the wrapper routines
to make it easier to merge the handling.
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
While processing the list of capabilities, it is useful to
filter out some of the entries based on the given mask for the
scope of the capabilities to allow better control. This can be
used later for handling LOCAL vs SYSTEM wide capabilities and more.
All capabilities should have their scope set to either LOCAL_CPU or
SYSTEM. No functional/flow change.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that each capability describes how to treat the conflicts
of CPU cap state vs System wide cap state, we can unify the
verification logic to a single place.
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When a CPU is brought up, it is checked against the caps that are
known to be enabled on the system (via verify_local_cpu_capabilities()).
Based on the state of the capability on the CPU vs. that of System we
could have the following combinations of conflict.
x-----------------------------x
| Type | System | Late CPU |
|-----------------------------|
| a | y | n |
|-----------------------------|
| b | n | y |
x-----------------------------x
Case (a) is not permitted for caps which are system features, which the
system expects all the CPUs to have (e.g VHE). While (a) is ignored for
all errata work arounds. However, there could be exceptions to the plain
filtering approach. e.g, KPTI is an optional feature for a late CPU as
long as the system already enables it.
Case (b) is not permitted for errata work arounds that cannot be activated
after the kernel has finished booting.And we ignore (b) for features. Here,
yet again, KPTI is an exception, where if a late CPU needs KPTI we are too
late to enable it (because we change the allocation of ASIDs etc).
Add two different flags to indicate how the conflict should be handled.
ARM64_CPUCAP_PERMITTED_FOR_LATE_CPU - CPUs may have the capability
ARM64_CPUCAP_OPTIONAL_FOR_LATE_CPU - CPUs may not have the cappability.
Now that we have the flags to describe the behavior of the errata and
the features, as we treat them, define types for ERRATUM and FEATURE.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We use arm64_cpu_capabilities to represent CPU ELF HWCAPs exposed
to the userspace and the CPU hwcaps used by the kernel, which
include cpu features and CPU errata work arounds. Capabilities
have some properties that decide how they should be treated :
1) Detection, i.e scope : A cap could be "detected" either :
- if it is present on at least one CPU (SCOPE_LOCAL_CPU)
Or
- if it is present on all the CPUs (SCOPE_SYSTEM)
2) When is it enabled ? - A cap is treated as "enabled" when the
system takes some action based on whether the capability is detected or
not. e.g, setting some control register, patching the kernel code.
Right now, we treat all caps are enabled at boot-time, after all
the CPUs are brought up by the kernel. But there are certain caps,
which are enabled early during the boot (e.g, VHE, GIC_CPUIF for NMI)
and kernel starts using them, even before the secondary CPUs are brought
up. We would need a way to describe this for each capability.
3) Conflict on a late CPU - When a CPU is brought up, it is checked
against the caps that are known to be enabled on the system (via
verify_local_cpu_capabilities()). Based on the state of the capability
on the CPU vs. that of System we could have the following combinations
of conflict.
x-----------------------------x
| Type | System | Late CPU |
------------------------------|
| a | y | n |
------------------------------|
| b | n | y |
x-----------------------------x
Case (a) is not permitted for caps which are system features, which the
system expects all the CPUs to have (e.g VHE). While (a) is ignored for
all errata work arounds. However, there could be exceptions to the plain
filtering approach. e.g, KPTI is an optional feature for a late CPU as
long as the system already enables it.
Case (b) is not permitted for errata work arounds which requires some
work around, which cannot be delayed. And we ignore (b) for features.
Here, yet again, KPTI is an exception, where if a late CPU needs KPTI we
are too late to enable it (because we change the allocation of ASIDs
etc).
So this calls for a lot more fine grained behavior for each capability.
And if we define all the attributes to control their behavior properly,
we may be able to use a single table for the CPU hwcaps (which cover
errata and features, not the ELF HWCAPs). This is a prepartory step
to get there. More bits would be added for the properties listed above.
We are going to use a bit-mask to encode all the properties of a
capabilities. This patch encodes the "SCOPE" of the capability.
As such there is no change in how the capabilities are treated.
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We have errata work around processing code in cpu_errata.c,
which calls back into helpers defined in cpufeature.c. Now
that we are going to make the handling of capabilities
generic, by adding the information to each capability,
move the errata work around specific processing code.
No functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We trigger CPU errata work around check on the boot CPU from
smp_prepare_boot_cpu() to make sure that we run the checks only
after the CPU feature infrastructure is initialised. While this
is correct, we can also do this from init_cpu_features() which
initilises the infrastructure, and is called only on the
Boot CPU. This helps to consolidate the CPU capability handling
to cpufeature.c. No functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We issue the enable() call back for all CPU hwcaps capabilities
available on the system, on all the CPUs. So far we have ignored
the argument passed to the call back, which had a prototype to
accept a "void *" for use with on_each_cpu() and later with
stop_machine(). However, with commit 0a0d111d40
("arm64: cpufeature: Pass capability structure to ->enable callback"),
there are some users of the argument who wants the matching capability
struct pointer where there are multiple matching criteria for a single
capability. Clean up the declaration of the call back to make it clear.
1) Renamed to cpu_enable(), to imply taking necessary actions on the
called CPU for the entry.
2) Pass const pointer to the capability, to allow the call back to
check the entry. (e.,g to check if any action is needed on the CPU)
3) We don't care about the result of the call back, turning this to
a void.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: James Morse <james.morse@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Dave Martin <dave.martin@arm.com>
[suzuki: convert more users, rename call back and drop results]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use of SVE by EL2 and below requires explicit support in the
firmware. There is no means to hide the presence of SVE from EL2,
so a kernel configured with CONFIG_ARM64_SVE=y will typically not
work correctly on SVE capable hardware unless the firmware does
include the appropriate support.
This is not expected to pose a problem in the wild, since platform
integrators are responsible for ensuring that they ship up-to-date
firmware to support their hardware. However, developers may hit
the issue when using mismatched compoments.
In order to draw attention to the issue and how to solve it, this
patch adds some Kconfig text giving a brief explanation and details
of compatible firmware versions.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The decision to rebuild .S_shipped is made based on the relative
timestamps of .S_shipped and .pl files but git makes this essentially
random. This means that the perl script might run anyway (usually at
most once per checkout), defeating the whole purpose of _shipped.
Fix by skipping the rule unless explicit make variables are provided:
REGENERATE_ARM_CRYPTO or REGENERATE_ARM64_CRYPTO.
This can produce nasty occasional build failures downstream, for example
for toolchains with broken perl. The solution is minimally intrusive to
make it easier to push into stable.
Another report on a similar issue here: https://lkml.org/lkml/2018/3/8/1379
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch enables the CONFIG_STMMAC_ETH to the default arm64 defconfig:
-CONFIG_STMMAC_ETH=m
+CONFIG_STMMAC_ETH=y
+CONFIG_DWMAC_IPQ806X=m
+CONFIG_DWMAC_MESON=m
+CONFIG_DWMAC_ROCKCHIP=m
+CONFIG_DWMAC_SUNXI=m
+CONFIG_DWMAC_SUN8I=m
The STMMAC ethernet controller is on the Stratix10 platform, and thus needs
driver to be in the kernel image for NFS to work.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
On architectures with CONFIG_HAVE_ARCH_HUGE_VMAP set, ioremap() may
create pud/pmd mappings. A kernel panic was observed on arm64 systems
with Cortex-A75 in the following steps as described by Hanjun Guo.
1. ioremap a 4K size, valid page table will build,
2. iounmap it, pte0 will set to 0;
3. ioremap the same address with 2M size, pgd/pmd is unchanged,
then set the a new value for pmd;
4. pte0 is leaked;
5. CPU may meet exception because the old pmd is still in TLB,
which will lead to kernel panic.
This panic is not reproducible on x86. INVLPG, called from iounmap,
purges all levels of entries associated with purged address on x86. x86
still has memory leak.
The patch changes the ioremap path to free unmapped page table(s) since
doing so in the unmap path has the following issues:
- The iounmap() path is shared with vunmap(). Since vmap() only
supports pte mappings, making vunmap() to free a pte page is an
overhead for regular vmap users as they do not need a pte page freed
up.
- Checking if all entries in a pte page are cleared in the unmap path
is racy, and serializing this check is expensive.
- The unmap path calls free_vmap_area_noflush() to do lazy TLB purges.
Clearing a pud/pmd entry before the lazy TLB purges needs extra TLB
purge.
Add two interfaces, pud_free_pmd_page() and pmd_free_pte_page(), which
clear a given pud/pmd entry and free up a page for the lower level
entries.
This patch implements their stub functions on x86 and arm64, which work
as workaround.
[akpm@linux-foundation.org: fix typo in pmd_free_pte_page() stub]
Link: http://lkml.kernel.org/r/20180314180155.19492-2-toshi.kani@hpe.com
Fixes: e61ce6ade4 ("mm: change ioremap to set up huge I/O mappings")
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Wang Xuefeng <wxf.wang@hisilicon.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Chintan Pandya <cpandya@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We would like to reset the Group-0 Active Priority Registers
at boot time if they are available to us. They would be available
if SCR_EL3.FIQ was not set, but we cannot directly probe this bit,
and short of checking, we may end-up trapping to EL3, and the
firmware may not be please to get such an exception. Yes, this
is dumb.
Instead, let's use PMR to find out if its value gets affected by
SCR_EL3.FIQ being set. We use the fact that when SCR_EL3.FIQ is
set, the LSB of the priority is lost due to the shifting back and
forth of the actual priority. If we read back a 0, we know that
Group0 is unavailable. In case we read a non-zero value, we can
safely reset the AP0Rn register.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds syscon property for specifying soc-glue core into
device-tree of LD11/LD20 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently a SIGFPE delivered in response to a floating-point
exception trap may have si_code set to 0 on arm64. As reported by
Eric, this is a bad idea since this is the value of SI_USER -- yet
this signal is definitely not the result of kill(2), tgkill(2) etc.
and si_uid and si_pid make limited sense whereas we do want to
yield a value for si_addr (which doesn't exist for SI_USER).
It's not entirely clear whether the architecure permits a
"spurious" fp exception trap where none of the exception flag bits
in ESR_ELx is set. (IMHO the architectural intent is to forbid
this.) However, it does permit those bits to contain garbage if
the TFV bit in ESR_ELx is 0. That case isn't currently handled at
all and may result in si_code == 0 or si_code containing a FPE_FLT*
constant corresponding to an exception that did not in fact happen.
There is nothing sensible we can return for si_code in such cases,
but SI_USER is certainly not appropriate and will lead to violation
of legitimate userspace assumptions.
This patch allocates a new si_code value FPE_UNKNOWN that at least
does not conflict with any existing SI_* or FPE_* code, and yields
this in si_code for undiagnosable cases. This is probably the best
simplicity/incorrectness tradeoff achieveable without relying on
implementation-dependent features or adding a lot of code. In any
case, there appears to be no perfect solution possible that would
justify a lot of effort here.
Yielding FPE_UNKNOWN when some well-defined fp exception caused the
trap is a violation of POSIX, but this is forced by the
architecture. We have no realistic prospect of yielding the
correct code in such cases. At present I am not aware of any ARMv8
implementation that supports trapped floating-point exceptions in
any case.
The new code may be applicable to other architectures for similar
reasons.
No attempt is made to provide ESR_ELx to userspace in the signal
frame, since architectural limitations mean that it is unlikely to
provide much diagnostic value, doesn't benefit existing software
and would create ABI with no proven purpose. The existing
mechanism for passing it also has problems of its own which may
result in the wrong value being passed to userspace due to
interaction with mm faults. The implied rework does not appear
justified.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.
Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:
- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port
Adds initial support for it, including the UART on the Expansion pin
header.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.
This commit adds the basical DTSI file of it, including the clock
support and UART support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The function SMCCC_ARCH_WORKAROUND_1 was introduced as part of SMC
V1.1 Calling Convention to mitigate CVE-2017-5715. This patch uses
the standard call SMCCC_ARCH_WORKAROUND_1 for Falkor chips instead
of Silicon provider service ID 0xC2001700.
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Expose the new features introduced by Arm v8.4 extensions to
Arm v8-A profile.
These include :
1) Data indpendent timing of instructions. (DIT, exposed as HWCAP_DIT)
2) Unaligned atomic instructions and Single-copy atomicity of loads
and stores. (AT, expose as HWCAP_USCAT)
3) LDAPR and STLR instructions with immediate offsets (extension to
LRCPC, exposed as HWCAP_ILRCPC)
4) Flag manipulation instructions (TS, exposed as HWCAP_FLAGM).
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we started keeping modules within 4 GB of the core kernel
in all cases, we no longer need to special case the adr_l/ldr_l/str_l
macros for modules to deal with them being loaded farther away.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The printk symbol was intended as a generic address that is always
exported, however that turned out to be false with CONFIG_PRINTK=n:
ERROR: "printk" [arch/arm64/kernel/arm64-reloc-test.ko] undefined!
This changes the references to memstart_addr, which should be there
regardless of configuration.
Fixes: a257e02579 ("arm64/kernel: don't ban ADRP to work around Cortex-A53 erratum #843419")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The schematic of the espressobin is publicly available, add a comment
where to find it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cortex-A57 and A72 are vulnerable to the so-called "variant 3a" of
Meltdown, where an attacker can speculatively obtain the value
of a privileged system register.
By enabling ARM64_HARDEN_EL2_VECTORS on these CPUs, obtaining
VBAR_EL2 is not disclosing the hypervisor mappings anymore.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're now ready to map our vectors in weird and wonderful locations.
On enabling ARM64_HARDEN_EL2_VECTORS, a vector slot gets allocated
if this hasn't been already done via ARM64_HARDEN_BRANCH_PREDICTOR
and gets mapped outside of the normal RAM region, next to the
idmap.
That way, being able to obtain VBAR_EL2 doesn't reveal the mapping
of the rest of the hypervisor code.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're about to need to allocate hardening slots from other parts
of the kernel (in order to support ARM64_HARDEN_EL2_VECTORS).
Turn the counter into an atomic_t and make it available to the
rest of the kernel. Also add BP_HARDEN_EL2_SLOTS as the number of
slots instead of the hardcoded 4...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Until now, all EL2 executable mappings were derived from their
EL1 VA. Since we want to decouple the vectors mapping from
the rest of the hypervisor, we need to be able to map some
text somewhere else.
The "idmap" region (for lack of a better name) is ideally suited
for this, as we have a huge range that hardly has anything in it.
Let's extend the IO allocator to also deal with executable mappings,
thus providing the required feature.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, the branch from the vector slots to the main vectors can at
most be 4GB from the main vectors (the reach of ADRP), and this
distance is known at compile time. If we were to remap the slots
to an unrelated VA, things would break badly.
A way to achieve VA independence would be to load the absolute
address of the vectors (__kvm_hyp_vector), either using a constant
pool or a series of movs, followed by an indirect branch.
This patches implements the latter solution, using another instance
of a patching callback. Note that since we have to save a register
pair on the stack, we branch to the *second* instruction in the
vectors in order to compensate for it. This also results in having
to adjust this balance in the invalid vector entry point.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we only reserve a single instruction in the BPI template in
order to branch to the vectors. As we're going to stuff a few more
instructions there, let's reserve a total of 5 instructions, which
we're going to patch later on as required.
We also introduce a small refactor of the vectors themselves, so that
we stop carrying the target branch around.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no reason why the BP hardening vectors shouldn't be part
of the HYP text at compile time, rather than being mapped at runtime.
Also introduce a new config symbol that controls the compilation
of bpi.S.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
All our useful entry points into the hypervisor are starting by
saving x0 and x1 on the stack. Let's move those into the vectors
by introducing macros that annotate whether a vector is valid or
not, thus indicating whether we want to stash registers or not.
The only drawback is that we now also stash registers for el2_error,
but this should never happen, and we pop them back right at the
start of the handling sequence.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently provide the hyp-init code with a kernel VA, and expect
it to turn it into a HYP va by itself. As we're about to provide
the hypervisor with mappings that are not necessarily in the memory
range, let's move the kern_hyp_va macro to kvm_get_hyp_vector.
No functionnal change.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The main idea behind randomising the EL2 VA is that we usually have
a few spare bits between the most significant bit of the VA mask
and the most significant bit of the linear mapping.
Those bits could be a bunch of zeroes, and could be useful
to move things around a bit. Of course, the more memory you have,
the less randomisation you get...
Alternatively, these bits could be the result of KASLR, in which
case they are already random. But it would be nice to have a
*different* randomization, just to make the job of a potential
attacker a bit more difficult.
Inserting these random bits is a bit involved. We don't have a spare
register (short of rewriting all the kern_hyp_va call sites), and
the immediate we want to insert is too random to be used with the
ORR instruction. The best option I could come up with is the following
sequence:
and x0, x0, #va_mask
ror x0, x0, #first_random_bit
add x0, x0, #(random & 0xfff)
add x0, x0, #(random >> 12), lsl #12
ror x0, x0, #(63 - first_random_bit)
making it a fairly long sequence, but one that a decent CPU should
be able to execute without breaking a sweat. It is of course NOPed
out on VHE. The last 4 instructions can also be turned into NOPs
if it appears that there is no free bits to use.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're moving towards a much more dynamic way to compute our
HYP VA, let's express the mask in a slightly different way.
Instead of comparing the idmap position to the "low" VA mask,
we directly compute the mask by taking into account the idmap's
(VA_BIT-1) bit.
No functionnal change.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The encoder for ADD/SUB (immediate) can only cope with 12bit
immediates, while there is an encoding for a 12bit immediate shifted
by 12 bits to the left.
Let's fix this small oversight by allowing the LSL_12 bit to be set.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add an encoder for the EXTR instruction, which also implements the ROR
variant (where Rn == Rm).
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're about to change the way we map devices at HYP, we need
to move away from kern_hyp_va on an IO address.
One way of achieving this is to store the VAs in kvm_vgic_global_state,
and use that directly from the HYP code. This requires a small change
to create_hyp_io_mappings so that it can also return a HYP VA.
We take this opportunity to nuke the vctrl_base field in the emulated
distributor, as it is not used anymore.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Both HYP io mappings call ioremap, followed by create_hyp_io_mappings.
Let's move the ioremap call into create_hyp_io_mappings itself, which
simplifies the code a bit and allows for further refactoring.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kvm_vgic_global_state is part of the read-only section, and is
usually accessed using a PC-relative address generation (adrp + add).
It is thus useless to use kern_hyp_va() on it, and actively problematic
if kern_hyp_va() becomes non-idempotent. On the other hand, there is
no way that the compiler is going to guarantee that such access is
always PC relative.
So let's bite the bullet and provide our own accessor.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we can dynamically compute the kernek/hyp VA mask, there
is no need for a feature flag to trigger the alternative patching.
Let's drop the flag and everything that depends on it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, we're using a complicated sequence of alternatives to
patch the kernel/hyp VA mask on non-VHE, and NOP out the
masking altogether when on VHE.
The newly introduced dynamic patching gives us the opportunity
to simplify that code by patching a single instruction with
the correct mask (instead of the mind bending cumulative masking
we have at the moment) or even a single NOP on VHE. This also
adds some initial code that will allow the patching callback
to switch to a more complex patching.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We lack a way to encode operations such as AND, ORR, EOR that take
an immediate value. Doing so is quite involved, and is all about
reverse engineering the decoding algorithm described in the
pseudocode function DecodeBitMasks().
This has been tested by feeding it all the possible literal values
and comparing the output with that of GAS.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're missing the a way to generate the encoding of the N immediate,
which is only a single bit used in a number of instruction that take
an immediate.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We've so far relied on a patching infrastructure that only gave us
a single alternative, without any way to provide a range of potential
replacement instructions. For a single feature, this is an all or
nothing thing.
It would be interesting to have a more flexible grained way of patching
the kernel though, where we could dynamically tune the code that gets
injected.
In order to achive this, let's introduce a new form of dynamic patching,
assiciating a callback to a patching site. This callback gets source and
target locations of the patching request, as well as the number of
instructions to be patched.
Dynamic patching is declared with the new ALTERNATIVE_CB and alternative_cb
directives:
asm volatile(ALTERNATIVE_CB("mov %0, #0\n", callback)
: "r" (v));
or
alternative_cb callback
mov x0, #0
alternative_cb_end
where callback is the C function computing the alternative.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We can finally get completely rid of any calls to the VGICv3
save/restore functions when the AP lists are empty on VHE systems. This
requires carefully factoring out trap configuration from saving and
restoring state, and carefully choosing what to do on the VHE and
non-VHE path.
One of the challenges is that we cannot save/restore the VMCR lazily
because we can only write the VMCR when ICC_SRE_EL1.SRE is cleared when
emulating a GICv2-on-GICv3, since otherwise all Group-0 interrupts end
up being delivered as FIQ.
To solve this problem, and still provide fast performance in the fast
path of exiting a VM when no interrupts are pending (which also
optimized the latency for actually delivering virtual interrupts coming
from physical interrupts), we orchestrate a dance of only doing the
activate/deactivate traps in vgic load/put for VHE systems (which can
have ICC_SRE_EL1.SRE cleared when running in the host), and doing the
configuration on every round-trip on non-VHE systems.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The APRs can only have bits set when the guest acknowledges an interrupt
in the LR and can only have a bit cleared when the guest EOIs an
interrupt in the LR. Therefore, if we have no LRs with any
pending/active interrupts, the APR cannot change value and there is no
need to clear it on every exit from the VM (hint: it will have already
been cleared when we exited the guest the last time with the LRs all
EOIed).
The only case we need to take care of is when we migrate the VCPU away
from a CPU or migrate a new VCPU onto a CPU, or when we return to
userspace to capture the state of the VCPU for migration. To make sure
this works, factor out the APR save/restore functionality into separate
functions called from the VCPU (and by extension VGIC) put/load hooks.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Just like we can program the GICv2 hypervisor control interface directly
from the core vgic code, we can do the same for the GICv3 hypervisor
control interface on VHE systems.
We do this by simply calling the save/restore functions when we have VHE
and we can then get rid of the save/restore function calls from the VHE
world switch function.
One caveat is that we now write GICv3 system register state before the
potential early exit path in the run loop, and because we sync back
state in the early exit path, we have to ensure that we read a
consistent GIC state from the sync path, even though we have never
actually run the guest with the newly written GIC state. We solve this
by inserting an ISB in the early exit path.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The vgic-v2-sr.c file now only contains the logic to replay unaligned
accesses to the virtual CPU interface on 16K and 64K page systems, which
is only relevant on 64-bit platforms. Therefore move this file to the
arm64 KVM tree, remove the compile directive from the 32-bit side
makefile, and remove the ifdef in the C file.
Since this file also no longer saves/restores anything, rename the file
to vgic-v2-cpuif-proxy.c to more accurately describe the logic in this
file.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We can program the GICv2 hypervisor control interface logic directly
from the core vgic code and can instead do the save/restore directly
from the flush/sync functions, which can lead to a number of future
optimizations.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To make the code more readable and to avoid the overhead of a function
call, let's get rid of a pair of the alternative function selectors and
explicitly call the VHE and non-VHE functions using the has_vhe() static
key based selector instead, telling the compiler to try to inline the
static function if it can.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We do not have to change the c15 trap setting on each switch to/from the
guest on VHE systems, because this setting only affects guest EL1/EL0
(and therefore not the VHE host).
The PMU and debug trap configuration can also be done on vcpu load/put
instead, because they don't affect how the VHE host kernel can access the
debug registers while executing KVM kernel code.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no longer a need for an alternative to choose the right
function to tell us whether or not FPSIMD was enabled for the VM,
because we can simply can the appropriate functions directly from within
the _vhe and _nvhe run functions.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to be more lazy with some of the trap configuration
register read/writes for VHE systems, move the logic that is currently
shared between VHE and non-VHE into a separate function which can be
called from either the world-switch path or from vcpu_load/vcpu_put.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When running a 32-bit VM (EL1 in AArch32), the AArch32 system registers
can be deferred to vcpu load/put on VHE systems because neither
the host kernel nor host userspace uses these registers.
Note that we can't save DBGVCR32_EL2 conditionally based on the state of
the debug dirty flag on VHE after this change, because during
vcpu_load() we haven't calculated a valid debug flag yet, and when we've
restored the register during vcpu_load() we also have to save it during
vcpu_put(). This means that we'll always restore/save the register for
VHE on load/put, but luckily vcpu load/put are called rarely, so saving
an extra register unconditionally shouldn't significantly hurt
performance.
We can also not defer saving FPEXC32_32 because this register only holds
a guest-valid value for 32-bit guests during the exit path when the
guest has used FPSIMD registers and restored the register in the early
assembly handler from taking the EL2 fault, and therefore we have to
check if fpsimd is enabled for the guest in the exit path and save the
register then, for both VHE and non-VHE guests.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
32-bit registers are not used by a 64-bit host kernel and can be
deferred, but we need to rework the accesses to these register to access
the latest values depending on whether or not guest system registers are
loaded on the CPU or only reside in memory.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some system registers do not affect the host kernel's execution and can
therefore be loaded when we are about to run a VCPU and we don't have to
restore the host state to the hardware before the time when we are
actually about to return to userspace or schedule out the VCPU thread.
The EL1 system registers and the userspace state registers only
affecting EL0 execution do not need to be saved and restored on every
switch between the VM and the host, because they don't affect the host
kernel's execution.
We mark all registers which are now deffered as such in the
vcpu_{read,write}_sys_reg accessors in sys-regs.c to ensure the most
up-to-date copy is always accessed.
Note MPIDR_EL1 (controlled via VMPIDR_EL2) is accessed from other vcpu
threads, for example via the GIC emulation, and therefore must be
declared as immediate, which is fine as the guest cannot modify this
value.
The 32-bit sysregs can also be deferred but we do this in a separate
patch as it requires a bit more infrastructure.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ELR_EL1 is not used by a VHE host kernel and can be deferred, but we
need to rework the accesses to this register to access the latest value
depending on whether or not guest system registers are loaded on the CPU
or only reside in memory.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
SPSR_EL1 is not used by a VHE host kernel and can be deferred, but we
need to rework the accesses to this register to access the latest value
depending on whether or not guest system registers are loaded on the CPU
or only reside in memory.
The handling of accessing the various banked SPSRs for 32-bit VMs is a
bit clunky, but this will be improved in following patches which will
first prepare and subsequently implement deferred save/restore of the
32-bit registers, including the 32-bit SPSRs.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We are about to defer saving and restoring some groups of system
registers to vcpu_put and vcpu_load on supported systems. This means
that we need some infrastructure to access system registes which
supports either accessing the memory backing of the register or directly
accessing the system registers, depending on the state of the system
when we access the register.
We do this by defining read/write accessor functions, which can handle
both "immediate" and "deferrable" system registers. Immediate registers
are always saved/restored in the world-switch path, but deferrable
registers are only saved/restored in vcpu_put/vcpu_load when supported
and sysregs_loaded_on_cpu will be set in that case.
Note that we don't use the deferred mechanism yet in this patch, but only
introduce infrastructure. This is to improve convenience of review in
the subsequent patches where it is clear which registers become
deferred.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently we access the system registers array via the vcpu_sys_reg()
macro. However, we are about to change the behavior to some times
modify the register file directly, so let's change this to two
primitives:
* Accessor macros vcpu_write_sys_reg() and vcpu_read_sys_reg()
* Direct array access macro __vcpu_sys_reg()
The accessor macros should be used in places where the code needs to
access the currently loaded VCPU's state as observed by the guest. For
example, when trapping on cache related registers, a write to a system
register should go directly to the VCPU version of the register.
The direct array access macro can be used in places where the VCPU is
known to never be running (for example userspace access) or for
registers which are never context switched (for example all the PMU
system registers).
This rewrites all users of vcpu_sys_regs to one of the macros described
above.
No functional change.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently handle 32-bit accesses to trapped VM system registers using
the 32-bit index into the coproc array on the vcpu structure, which is a
union of the coproc array and the sysreg array.
Since all the 32-bit coproc indices are created to correspond to the
architectural mapping between 64-bit system registers and 32-bit
coprocessor registers, and because the AArch64 system registers are the
double in size of the AArch32 coprocessor registers, we can always find
the system register entry that we must update by dividing the 32-bit
coproc index by 2.
This is going to make our lives much easier when we have to start
accessing system registers that use deferred save/restore and might
have to be read directly from the physical CPU.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On non-VHE systems we need to save the ELR_EL2 and SPSR_EL2 so that we can
return to the host in EL1 in the same state and location where we issued a
hypercall to EL2, but on VHE ELR_EL2 and SPSR_EL2 are not useful because we
never enter a guest as a result of an exception entry that would be directly
handled by KVM. The kernel entry code already saves ELR_EL1/SPSR_EL1 on
exception entry, which is enough. Therefore, factor out these registers into
separate save/restore functions, making it easy to exclude them from the VHE
world-switch path later on.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to have multiple identical functions with different
names for saving host and guest state. When saving and restoring state
for the host and guest, the state is the same for both contexts, and
that's why we have the kvm_cpu_context structure. Delete one
version and rename the other into simply save/restore.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The comment only applied to SPE on non-VHE systems, so we simply remove
it.
Suggested-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to handle system registers quite differently between VHE
and non-VHE systems. In preparation for that, we need to split some of
the handling functions between VHE and non-VHE functionality.
For now, we simply copy the non-VHE functions, but we do change the use
of static keys for VHE and non-VHE functionality now that we have
separate functions.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to move calls around in the sysreg save/restore logic,
let's first rewrite the alternative function callers, because it is
going to make the next patches much easier to read.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There's a semantic difference between the EL1 registers that control
operation of a kernel running in EL1 and EL1 registers that only control
userspace execution in EL0. Since we can defer saving/restoring the
latter, move them into their own function.
The ARMv8 ARM (ARM DDI 0487C.a) Section D10.2.1 recommends that
ACTLR_EL1 has no effect on the processor when running the VHE host, and
we can therefore move this register into the EL1 state which is only
saved/restored on vcpu_put/load for a VHE host.
We also take this chance to rename the function saving/restoring the
remaining system register to make it clear this function deals with
the EL1 system registers.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The VHE switch function calls __timer_enable_traps and
__timer_disable_traps which don't do anything on VHE systems.
Therefore, simply remove these calls from the VHE switch function and
make the functions non-conditional as they are now only called from the
non-VHE switch path.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to reset the VTTBR to zero when exiting the guest on
VHE systems. VHE systems don't use stage 2 translations for the EL2&0
translation regime used by the host.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VHE kernels run completely in EL2 and therefore don't have a notion of
kernel and hyp addresses, they are all just kernel addresses. Therefore
don't call kern_hyp_va() in the VHE switch function.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far this is mostly (see below) a copy of the legacy non-VHE switch
function, but we will start reworking these functions in separate
directions to work on VHE and non-VHE in the most optimal way in later
patches.
The only difference after this patch between the VHE and non-VHE run
functions is that we omit the branch-predictor variant-2 hardening for
QC Falkor CPUs, because this workaround is specific to a series of
non-VHE ARMv8.0 CPUs.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current world-switch function has functionality to detect a number
of cases where we need to fixup some part of the exit condition and
possibly run the guest again, before having restored the host state.
This includes populating missing fault info, emulating GICv2 CPU
interface accesses when mapped at unaligned addresses, and emulating
the GICv3 CPU interface on systems that need it.
As we are about to have an alternative switch function for VHE systems,
but VHE systems still need the same early fixup logic, factor out this
logic into a separate function that can be shared by both switch
functions.
No functional change.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of having multiple calls from the world switch path to the debug
logic, each figuring out if the dirty bit is set and if we should
save/restore the debug registers, let's just provide two hooks to the
debug save/restore functionality, one for switching to the guest
context, and one for switching to the host context, and we get the
benefit of only having to evaluate the dirty flag once on each path,
plus we give the compiler some more room to inline some of this
functionality.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The debug save/restore functions can be improved by using the has_vhe()
static key instead of the instruction alternative. Using the static key
uses the same paradigm as we're going to use elsewhere, it makes the
code more readable, and it generates slightly better code (no
stack setups and function calls unless necessary).
We also use a static key on the restore path, because it will be
marginally faster than loading a value from memory.
Finally, we don't have to conditionally clear the debug dirty flag if
it's set, we can just clear it.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to figure out inside the world-switch if we should
save/restore the debug registers or not, we might as well do that in the
higher level debug setup code, making it easier to optimize down the
line.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We have numerous checks around that checks if the HCR_EL2 has the RW bit
set to figure out if we're running an AArch64 or AArch32 VM. In some
cases, directly checking the RW bit (given its unintuitive name), is a
bit confusing, and that's not going to improve as we move logic around
for the following patches that optimize KVM on AArch64 hosts with VHE.
Therefore, introduce a helper, vcpu_el1_is_32bit, and replace existing
direct checks of HCR_EL2.RW with the helper.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to move a bunch of save/restore logic for VHE kernels to
the load and put functions, we need some infrastructure to do this.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently have a separate read-modify-write of the HCR_EL2 on entry
to the guest for the sole purpose of setting the VF and VI bits, if set.
Since this is most rarely the case (only when using userspace IRQ chip
and interrupts are in flight), let's get rid of this operation and
instead modify the bits in the vcpu->arch.hcr[_el2] directly when
needed.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We always set the IMO and FMO bits in the HCR_EL2 when running the
guest, regardless if we use the vgic or not. By moving these flags to
HCR_GUEST_FLAGS we can avoid one of the extra save/restore operations of
HCR_EL2 in the world switch code, and we can also soon get rid of the
other one.
This is safe, because even though the IMO and FMO bits control both
taking the interrupts to EL2 and remapping ICC_*_EL1 to ICV_*_EL1 when
executed at EL1, as long as we ensure that these bits are clear when
running the EL1 host, we're OK, because we reset the HCR_EL2 to only
have the HCR_RW bit set when returning to EL1 on non-VHE systems.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shih-Wei Li <shihwei@cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VHE actually doesn't rely on clearing the VTTBR when returning to the
host kernel, and that is the current key mechanism of hyp_panic to
figure out how to attempt to return to a state good enough to print a
panic statement.
Therefore, we split the hyp_panic function into two functions, a VHE and
a non-VHE, keeping the non-VHE version intact, but changing the VHE
behavior.
The vttbr_el2 check on VHE doesn't really make that much sense, because
the only situation where we can get here on VHE is when the hypervisor
assembly code actually called into hyp_panic, which only happens when
VBAR_EL2 has been set to the KVM exception vectors. On VHE, we can
always safely disable the traps and restore the host registers at this
point, so we simply do that unconditionally and call into the panic
function directly.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We already have the percpu area for the host cpu state, which points to
the VCPU, so there's no need to store the VCPU pointer on the stack on
every context switch. We can be a little more clever and just use
tpidr_el2 for the percpu offset and load the VCPU pointer from the host
context.
This has the benefit of being able to retrieve the host context even
when our stack is corrupted, and it has a potential performance benefit
because we trade a store plus a load for an mrs and a load on a round
trip to the guest.
This does require us to calculate the percpu offset without including
the offset from the kernel mapping of the percpu array to the linear
mapping of the array (which is what we store in tpidr_el1), because a
PC-relative generated address in EL2 is already giving us the hyp alias
of the linear mapping of a kernel address. We do this in
__cpu_init_hyp_mode() by using kvm_ksym_ref().
The code that accesses ESR_EL2 was previously using an alternative to
use the _EL1 accessor on VHE systems, but this was actually unnecessary
as the _EL1 accessor aliases the ESR_EL2 register on VHE, and the _EL2
accessor does the same thing on both systems.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Calling vcpu_load() registers preempt notifiers for this vcpu and calls
kvm_arch_vcpu_load(). The latter will soon be doing a lot of heavy
lifting on arm/arm64 and will try to do things such as enabling the
virtual timer and setting us up to handle interrupts from the timer
hardware.
Loading state onto hardware registers and enabling hardware to signal
interrupts can be problematic when we're not actually about to run the
VCPU, because it makes it difficult to establish the right context when
handling interrupts from the timer, and it makes the register access
code difficult to reason about.
Luckily, now when we call vcpu_load in each ioctl implementation, we can
simply remove the call from the non-KVM_RUN vcpu ioctls, and our
kvm_arch_vcpu_load() is only used for loading vcpu content to the
physical CPU when we're actually going to run the vcpu.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tweak the SHA256 update routines to invoke the SHA256 block transform
block by block, to avoid excessive scheduling delays caused by the
NEON algorithm running with preemption disabled.
Also, remove a stale comment which no longer applies now that kernel
mode NEON is actually disallowed in some contexts.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CBC MAC is strictly sequential, and so the current AES code simply
processes the input one block at a time. However, we are about to add
yield support, which adds a bit of overhead, and which we prefer to
align with other modes in terms of granularity (i.e., it is better to
have all routines yield every 64 bytes and not have an exception for
CBC MAC which yields every 16 bytes)
So unroll the loop by 4. We still cannot perform the AES algorithm in
parallel, but we can at least merge the loads and stores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CBC encryption is strictly sequential, and so the current AES code
simply processes the input one block at a time. However, we are
about to add yield support, which adds a bit of overhead, and which
we prefer to align with other modes in terms of granularity (i.e.,
it is better to have all routines yield every 64 bytes and not have
an exception for CBC encrypt which yields every 16 bytes)
So unroll the loop by 4. We still cannot perform the AES algorithm in
parallel, but we can at least merge the loads and stores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES block mode implementation using Crypto Extensions or plain NEON
was written before real hardware existed, and so its interleave factor
was made build time configurable (as well as an option to instantiate
all interleaved sequences inline rather than as subroutines)
We ended up using INTERLEAVE=4 with inlining disabled for both flavors
of the core AES routines, so let's stick with that, and remove the option
to configure this at build time. This makes the code easier to modify,
which is nice now that we're adding yield support.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Note that this requires some reshuffling of the registers in the asm
code, because the XTS routines can no longer rely on the registers to
retain their contents between invocations.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When kernel mode NEON was first introduced on arm64, the preserve and
restore of the userland NEON state was completely unoptimized, and
involved saving all registers on each call to kernel_neon_begin(),
and restoring them on each call to kernel_neon_end(). For this reason,
the NEON crypto code that was introduced at the time keeps the NEON
enabled throughout the execution of the crypto API methods, which may
include calls back into the crypto API that could result in memory
allocation or other actions that we should avoid when running with
preemption disabled.
Since then, we have optimized the kernel mode NEON handling, which now
restores lazily (upon return to userland), and so the preserve action
is only costly the first time it is called after entering the kernel.
So let's put the kernel_neon_begin() and kernel_neon_end() calls around
the actual invocations of the NEON crypto code, and run the remainder of
the code with kernel mode NEON disabled (and preemption enabled)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a NEON-accelerated implementation of Speck128-XTS and Speck64-XTS
for ARM64. This is ported from the 32-bit version. It may be useful on
devices with 64-bit ARM CPUs that don't have the Cryptography
Extensions, so cannot do AES efficiently -- e.g. the Cortex-A53
processor on the Raspberry Pi 3.
It generally works the same way as the 32-bit version, but there are
some slight differences due to the different instructions, registers,
and syntax available in ARM64 vs. in ARM32. For example, in the 64-bit
version there are enough registers to hold the XTS tweaks for each
128-byte chunk, so they don't need to be saved on the stack.
Benchmarks on a Raspberry Pi 3 running a 64-bit kernel:
Algorithm Encryption Decryption
--------- ---------- ----------
Speck64/128-XTS (NEON) 92.2 MB/s 92.2 MB/s
Speck128/256-XTS (NEON) 75.0 MB/s 75.0 MB/s
Speck128/256-XTS (generic) 47.4 MB/s 35.6 MB/s
AES-128-XTS (NEON bit-sliced) 33.4 MB/s 29.6 MB/s
AES-256-XTS (NEON bit-sliced) 24.6 MB/s 21.7 MB/s
The code performs well on higher-end ARM64 processors as well, though
such processors tend to have the Crypto Extensions which make AES
preferred. For example, here are the same benchmarks run on a HiKey960
(with CPU affinity set for the A73 cores), with the Crypto Extensions
implementation of AES-256-XTS added:
Algorithm Encryption Decryption
--------- ----------- -----------
AES-256-XTS (Crypto Extensions) 1273.3 MB/s 1274.7 MB/s
Speck64/128-XTS (NEON) 359.8 MB/s 348.0 MB/s
Speck128/256-XTS (NEON) 292.5 MB/s 286.1 MB/s
Speck128/256-XTS (generic) 186.3 MB/s 181.8 MB/s
AES-128-XTS (NEON bit-sliced) 142.0 MB/s 124.3 MB/s
AES-256-XTS (NEON bit-sliced) 104.7 MB/s 91.1 MB/s
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull "Freescale arm64 device tree updates for 4.17" from Shawn Guo:
- Move cpu_thermal device out of bus node to fix DTC simple_bus_reg
warning seen with W=1 switch.
- Fix IFC child nodes' unit-address to eliminate DTC simple_bus_reg
warnings.
- Add a dummy size memory 'reg' property for LS1046A device tree to
avoid unit_address_vs_reg DTC warning, and the real size will be
filled by bootloader.
- Update ls208xa-qds board device tree to fix unit_address_vs_reg
warnings with DSPI device.
- Add idle-states for LS1012A and LS1043A, and correct
arm,psci-suspend-param setting for already added idle-states.
- DPAA QBMan portal and watchdog device addition.
* tag 'imx-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: ifc: Fix the unit address format in the examples
arm64: dts: ls1046a: add a dummy memory 'reg' property
arm64: dts: fsl: fix ifc simple-bus unit address format warnings
arm64: dts: fsl: update the cpu idle node
arm64: dts: ls1043a: add cpu idle support
arm64: dts: ls1012a: add cpu idle support
arm64: dts: ls208xa-qds: Fix the 'reg' property
arm64: dts: ls208xa-qds: Pass unit name to dspi child nodes
arm64: dts: ls208xa: Move cpu_thermal out of bus node
arm64: dts: ls1088a: Move cpu_thermal out of bus node
arm64: dts: ls1046a: Move cpu_thermal out of bus node
arm64: dts: ls1043a: Move cpu_thermal out of bus node
arm64: dts: ls1012a: Move cpu_thermal out of bus node
arm64: dts: Add DPAA QBMan portal 9
arm64: dts: ls1088a: add DT node of watchdog
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
-----BEGIN PGP SIGNATURE-----
iQJJBAABCAAzFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAlqqp/cVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJECPQ0LrRPXpDAGkP/2LMhFN561PKlqgu5V4hFvowJiXb
Gbb/qi095vtDGccbKmJKAZp3jyOM2oJEMUkx5RBYglWjW0mxb3zPAAxhldXiqv/2
CrOGGlS/FwfyIjCt7870pltDOIgRmk8Fv/MyQjjGKF6VAghd6yVHIZiOUjiriUyz
6hNyc2znLm0tBqm4j3HTXKHpD23YseW387pQoeQ03/WiXiZ60O3e3k0yppXO81qE
b7TGT4Bz04mxlAISZVZeTmG7P7P4ej6+NhOH+1kxacseLzHdECPBA0JRcwRpfLkP
5JFodUOX7/KHpvpMLUxRNRnLBei9WUL4o2LAEV0qDaj7nlAud0kKUm22RLaVKDm+
8FSUQ12XKqnZsRrl6IizU1oAb1I1iV3j9HF5iNf3mk9AO27REGk0b8fDyRzDj300
xpySgvIgA+f+EyY+3ve0AmEUa5QKz/WLuik2ZCqpVOuufrO8XpS+zjn1L1tzTlkR
95EahDA7enutw47G0uWtxoPMeU4HTZS/CAiFwUbq8BEK7T3Rct7UySPLwgeYBoji
MUlCRhPyAANCJmtO6rpOS3htkQ3XkkO1DVIGLuWC5Zl00W1T5I5+VRrVL1YI4v3O
d2ui9r5X5Vmg4OUdhr2D9fXgPWWKEbqD90jv40rGLsMl0g/IwrC+o2VxgYxSeu5x
CLUYILwEA5NDZSof
=iyYE
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-for-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
kvm/arm fixes for 4.16, take 2
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds regulators that have fixed voltage for audio codec
on UniPhier LD11/20 Global boards. This patch fixes warnings about
TAS57xx audio codec such as "tas571x 0-001b: 0-001b supply AVDD
not found, using dummy regulator".
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds compress audio node for S/PDIF on UniPhier LD11/20
global boards. And adds settings of AIO for it.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds codec node for TI TAS571x on UniPhier LD11/20
global boards. And adds settings of AIO for speaker out.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling vcpu_load() registers preempt notifiers for this vcpu and calls
kvm_arch_vcpu_load(). The latter will soon be doing a lot of heavy
lifting on arm/arm64 and will try to do things such as enabling the
virtual timer and setting us up to handle interrupts from the timer
hardware.
Loading state onto hardware registers and enabling hardware to signal
interrupts can be problematic when we're not actually about to run the
VCPU, because it makes it difficult to establish the right context when
handling interrupts from the timer, and it makes the register access
code difficult to reason about.
Luckily, now when we call vcpu_load in each ioctl implementation, we can
simply remove the call from the non-KVM_RUN vcpu ioctls, and our
kvm_arch_vcpu_load() is only used for loading vcpu content to the
physical CPU when we're actually going to run the vcpu.
Cc: stable@vger.kernel.org
Fixes: 9b062471e5 ("KVM: Move vcpu_load to arch-specific kvm_arch_vcpu_ioctl")
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable AHCI on Jetson TX1 and add sata phy node.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Display and graphics can't work together without an SMMU, so it is
effectively always getting enabled anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Suzuki K Poulose