Currently, conversion of SW S/G table into HW S/G layout relies on
nents returned by sg_nents_for_len(sg, len).
However this leaves the possibility of HW S/G referencing more data
then needed: since buffer length in HW S/G entries is filled using
sg_dma_len(sg), the last entry in HW S/G table might have a length
that is bigger than needed for the crypto request.
This way of S/G table conversion is fine, unless after converting a table
more entries have to be appended to the HW S/G table.
In this case, crypto engine would access data from the S/G entry having
the incorrect length, instead of advancing in the S/G table.
This situation doesn't exist, but the upcoming implementation of
IV update for skcipher algorithms needs to add a S/G entry after
req->dst S/G (corresponding to output IV).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CAAM driver used to put its debug messages inside #ifdef DEBUG and
then prints the messages at KERN_ERR level. Replace this with proper
functions printing at KERN_DEBUG level. The #ifdef DEBUG gets
unnecessary when the right functions are used.
This replaces:
- print_hex_dump(KERN_ERR ...) inside #ifdef DEBUG with
print_hex_dump_debug(...)
- dev_err() inside #ifdef DEBUG with dev_dbg()
- printk(KERN_ERR ...) inside #ifdef DEBUG with dev_dbg()
Some parts of the driver use these functions already, so it is only
consequent to use the debug function consistently.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CAAM driver defines its own debug() macro, but it is unused. Remove
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we allow top level code, i.e. that which sits between the
low level (HW-specific) drivers and crypto API, to be built as several
drivers: caamalg, caamhash, caam_pkc, caamrng, caamalg_qi.
There is no advantage in this, more it interferes with adding support
for deferred probing (there are no corresponding devices and thus
no bus).
Convert these drivers and call init() / exit() manually at the right
time.
Move algorithms initialization at JR probe / remove time:
-the first probed JR registers the crypto algs
-the last removed JR unregisters the crypto algs
Note: caam_qi_init() is called before JR platform devices creation
(of_populate_bus()), such that QI interface is initialized when
the caam/qi algorithms are registered in the JR driver (by calling
caam_qi_algapi_init().
While here, fix the Kconfig entries under CRYPTO_DEV_FSL_CAAM_JR
to be aligned.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to CAAM RM:
-crypto engine reads 4 S/G entries (64 bytes) at a time,
even if the S/G table has fewer entries
-it's the responsibility of the user / programmer to make sure
this HW behaviour has no side effect
The drivers do not take care of this currently, leading to IOMMU faults
when the S/G table ends close to a page boundary - since only one page
is DMA mapped, while CAAM's DMA engine accesses two pages.
Fix this by rounding up the number of allocated S/G table entries
to a multiple of 4.
Note that in case of two *contiguous* S/G tables, only the last table
might needs extra entries.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix a side effect of adding xcbc support, when the next_buffer is not
copied.
The issue occurs, when there is stored from previous state a blocksize
buffer and received, a less than blocksize, from user. In this case, the
nents for req->src is 0, and the next_buffer is not copied.
An example is:
{
.tap = { 17, 15, 8 },
.psize = 40,
.np = 3,
.ksize = 16,
}
Fixes: 12b8567f6f ("crypto: caam - add support for xcbc(aes)")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Fixes: 35af640386 ("crypto: caam - Check for CAAM block presence before registering with crypto layer")
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When generating a split key or hashing the key, DMA mapping the key
buffers coming directly from user is incorrect, since they are
not guaranteed to be DMAable.
Update driver to first copy user-provided key in the output buffer
("key_out") and then use this buffer for in-place computation
(split key generation, respectively key hashing).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix a side effect of adding xcbc support, which leads to DMA mapping the
key twice.
Fixes: 12b8567f6f ("crypto: caam - add support for xcbc(aes)")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When driver started using state->caam_ctxt for storing both running hash
and final hash, it was not updated to handle different DMA unmap
lengths.
Cc: <stable@vger.kernel.org> # v4.19+
Fixes: c19650d6ea ("crypto: caam - fix DMA mapping of stack memory")
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Roland reports the following issue and provides a root cause analysis:
"On a v4.19 i.MX6 system with IMA and CONFIG_DMA_API_DEBUG enabled, a
warning is generated when accessing files on a filesystem for which IMA
measurement is enabled:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/debug.c:1181 check_for_stack.part.9+0xd0/0x120
caam_jr 2101000.jr0: DMA-API: device driver maps memory from stack [addr=b668049e]
Modules linked in:
CPU: 0 PID: 1 Comm: switch_root Not tainted 4.19.0-20181214-1 #2
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c010efb8>] (dump_backtrace) from [<c010f2d0>] (show_stack+0x20/0x24)
[<c010f2b0>] (show_stack) from [<c08b04f4>] (dump_stack+0xa0/0xcc)
[<c08b0454>] (dump_stack) from [<c012b610>] (__warn+0xf0/0x108)
[<c012b520>] (__warn) from [<c012b680>] (warn_slowpath_fmt+0x58/0x74)
[<c012b62c>] (warn_slowpath_fmt) from [<c0199acc>] (check_for_stack.part.9+0xd0/0x120)
[<c01999fc>] (check_for_stack.part.9) from [<c019a040>] (debug_dma_map_page+0x144/0x174)
[<c0199efc>] (debug_dma_map_page) from [<c065f7f4>] (ahash_final_ctx+0x5b4/0xcf0)
[<c065f240>] (ahash_final_ctx) from [<c065b3c4>] (ahash_final+0x1c/0x20)
[<c065b3a8>] (ahash_final) from [<c03fe278>] (crypto_ahash_op+0x38/0x80)
[<c03fe240>] (crypto_ahash_op) from [<c03fe2e0>] (crypto_ahash_final+0x20/0x24)
[<c03fe2c0>] (crypto_ahash_final) from [<c03f19a8>] (ima_calc_file_hash+0x29c/0xa40)
[<c03f170c>] (ima_calc_file_hash) from [<c03f2b24>] (ima_collect_measurement+0x1dc/0x240)
[<c03f2948>] (ima_collect_measurement) from [<c03f0a60>] (process_measurement+0x4c4/0x6b8)
[<c03f059c>] (process_measurement) from [<c03f0cdc>] (ima_file_check+0x88/0xa4)
[<c03f0c54>] (ima_file_check) from [<c02d8adc>] (path_openat+0x5d8/0x1364)
[<c02d8504>] (path_openat) from [<c02dad24>] (do_filp_open+0x84/0xf0)
[<c02daca0>] (do_filp_open) from [<c02cf50c>] (do_open_execat+0x84/0x1b0)
[<c02cf488>] (do_open_execat) from [<c02d1058>] (__do_execve_file+0x43c/0x890)
[<c02d0c1c>] (__do_execve_file) from [<c02d1770>] (sys_execve+0x44/0x4c)
[<c02d172c>] (sys_execve) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
---[ end trace 3455789a10e3aefd ]---
The cause is that the struct ahash_request *req is created as a
stack-local variable up in the stack (presumably somewhere in the IMA
implementation), then passed down into the CAAM driver, which tries to
dma_single_map the req->result (indirectly via map_seq_out_ptr_result)
in order to make that buffer available for the CAAM to store the result
of the following hash operation.
The calling code doesn't know how req will be used by the CAAM driver,
and there could be other such occurrences where stack memory is passed
down to the CAAM driver. Therefore we should rather fix this issue in
the CAAM driver where the requirements are known."
Fix this problem by:
-instructing the crypto engine to write the final hash in state->caam_ctx
-subsequently memcpy-ing the final hash into req->result
Cc: <stable@vger.kernel.org> # v4.19+
Reported-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Tested-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add cmac(aes) keyed hash offloading support.
Similar to xcbc implementation, driver must make sure there are still
some bytes buffered when ahash_final() is called. This way HW is able to
decide whether padding is needed and which key to derive (L -> K1 / K2)
for the last block.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add xcbc(aes) offloading support.
Due to xcbc algorithm design and HW implementation in CAAM,
driver must still have some bytes to send to the crypto engine when
ahash_final() is called - such that HW correctly uses either K2 or K3
for the last block.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For keyed hash algorithms, shared descriptors are currently generated
twice:
-at tfm initialization time, in cra_init() callback
-in setkey() callback
Since it's mandatory to call setkey() for keyed algorithms, drop the
generation in cra_init().
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix error reporting when preparation of an hmac algorithm
for registration fails: print the hmac algorithm name, not the unkeyed
hash algorithm name.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Era 10 changes the register map.
The updates that affect the drivers:
-new version registers are added
-DBG_DBG[deco_state] field is moved to a new register -
DBG_EXEC[19:16] @ 8_0E3Ch.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previously, a tree-wide change added SPDX license identifiers to
files lacking licensing information:
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
To be consistent update the rest of the files:
-files with license specified by means of MODULE_LICENSE()
-files with complete license text
-Kconfig
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam/qi2 driver will support ahash algorithms,
thus move ahash descriptors generation in a shared location.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some ahash algorithms set .cra_type = &crypto_ahash_type. But this is
redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the .cra_type automatically.
Apparently the useless assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many ahash algorithms set .cra_flags = CRYPTO_ALG_TYPE_AHASH. But this
is redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Offload split key generation in CAAM engine, using DKP.
DKP is supported starting with Era 6.
Note that the way assoclen is transmitted from the job descriptor
to the shared descriptor changes - DPOVRD register is used instead
of MATH3 (where available), since DKP protocol thrashes the MATH
registers.
The replacement of MDHA split key generation with DKP has the side
effect of the crypto engine writing the authentication key, and thus
the DMA mapping direction for the buffer holding the key has to change
from DMA_TO_DEVICE to DMA_BIDIRECTIONAL.
There are two cases:
-key is inlined in descriptor - descriptor buffer mapping changes
-key is referenced - key buffer mapping changes
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ctx_map_to_sec4_sg() function, added in
commit 045e36780f ("crypto: caam - ahash hmac support")
has never used the "desc" parameter, so let's drop it.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Extended descriptor allocation has been changed by
commit dde20ae9d6 ("crypto: caam - Change kmalloc to kzalloc to avoid residual data")
to provide zeroized memory, meaning we no longer have to sanitize
its members - edesc->src_nents and edesc->dst_dma.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for using the caam/jr backend on DPAA2-based SoCs.
These have some particularities we have to account for:
-HW S/G format is different
-Management Complex (MC) firmware initializes / manages (partially)
the CAAM block: MCFGR, QI enablement in QICTL, RNG
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver does not properly handle the case when signals interrupt
wait_for_completion_interruptible():
-it does not check for return value
-completion structure is allocated on stack; in case a signal interrupts
the sleep, it will go out of scope, causing the worker thread
(caam_jr_dequeue) to fail when it accesses it
wait_for_completion_interruptible() is replaced with uninterruptable
wait_for_completion().
We choose to block all signals while waiting for I/O (device executing
the split key generation job descriptor) since the alternative - in
order to have a deterministic device state - would be to flush the job
ring (aborting *all* in-progress jobs).
Cc: <stable@vger.kernel.org>
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Fixes: 4c1ec1f930 ("crypto: caam - refactor key_gen, sg")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is the 2nd part of fixing the usage of GFP_KERNEL for memory
allocations, taking care off all the places that haven't caused a real
problem / failure.
Again, the issue being fixed is that GFP_KERNEL should be used only when
MAY_SLEEP flag is set, i.e. MAY_BACKLOG flag usage is orthogonal.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If we register the DMA API debug notification chain to
receive platform bus events:
dma_debug_add_bus(&platform_bus_type);
we start receiving warnings after a simple test like "modprobe caam_jr &&
modprobe caamhash && modprobe -r caamhash && modprobe -r caam_jr":
platform ffe301000.jr: DMA-API: device driver has pending DMA allocations while released from device [count=1938]
One of leaked entries details: [device address=0x0000000173fda090] [size=63 bytes] [mapped with DMA_TO_DEVICE] [mapped as single]
It turns out there are several issues with handling buf_dma (mapping of buffer
holding the previous chunk smaller than hash block size):
-detection of buf_dma mapping failure occurs too late, after a job descriptor
using that value has been submitted for execution
-dma mapping leak - unmapping is not performed in all places: for e.g.
in ahash_export or in most ahash_fin* callbacks (due to current back-to-back
implementation of buf_dma unmapping/mapping)
Fix these by:
-calling dma_mapping_error() on buf_dma right after the mapping and providing
an error code if needed
-unmapping buf_dma during the "job done" (ahash_done_*) callbacks
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caamhash uses double buffering for holding previous/current
and next chunks (data smaller than block size) to be hashed.
Add (inline) functions to abstract this mechanism.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case ctx_dma dma mapping fails, ahash_unmap_ctx() tries to
dma unmap an invalid address:
map_seq_out_ptr_ctx() / ctx_map_to_sec4_sg() -> goto unmap_ctx ->
-> ahash_unmap_ctx() -> dma unmap ctx_dma
There is also possible to reach ahash_unmap_ctx() with ctx_dma
uninitialzed or to try to unmap the same address twice.
Fix these by setting ctx_dma = 0 where needed:
-initialize ctx_dma in ahash_init()
-clear ctx_dma in case of mapping error (instead of holding
the error code returned by the dma map function)
-clear ctx_dma after each unmapping
Fixes: 32686d34f8 ("crypto: caam - ensure that we clean up after an error")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
setkey() callback may be invoked multiple times for the same tfm.
In this case, DMA API leaks are caused by shared descriptors
(and key for caamalg) being mapped several times and unmapped only once.
Fix this by performing mapping / unmapping only in crypto algorithm's
cra_init() / cra_exit() callbacks and sync_for_device in the setkey()
tfm callback.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Shared descriptors for hash algorithms are small enough
for (split) keys to be inlined in all cases.
Since driver already does this, all what's left is to remove
unused ctx->key_dma.
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move ahash shared descriptor generation into a single function.
Currently there is no plan to support ahash on any other interface
besides the Job Ring, thus for now the functionality is not exported.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move split key length and padded length computation from caamalg.c
and caamhash.c to key_gen.c.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A few descriptor commands are generated using generic
inline append "append_cmd" function.
Rewrite them using specific inline append functions.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Information carried by alg_op can be deduced from adata->algtype
plus some fixed flags.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of factoring out the shared descriptors,
struct alginfo is introduced to group the algorithm related
parameters.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Shared descriptors used by ahash_final() and ahash_finup()
are identical, thus get rid of one of them (sh_desc_finup).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 4464a7d4f5
("crypto: caam - remove error propagation handling")
removed error propagation handling only from caamalg.
Do this in all other places: caamhash, caamrng.
Update descriptors' lengths appropriately.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move statements for error handling which were identical
in two if branches to the end of these functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* Return a value at the end without storing it in an intermediate variable.
* Delete the local variable "ret" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adjust jump labels according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adjust jump labels according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a helper to map the source scatterlist into the descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a helper function to perform the descriptor allocation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Horia Geantă