The regmap stride is set to 1 for regmap describing 8bit registers already.
However, for 16/32/64bit registers, the stride is 2/4/8 respectively. This
is not correct, as the switch protocol supports unaligned register reads
and writes and the KSZ87xx even uses such unaligned register accesses to
read e.g. MIB counter.
This patch fixes MIB counter access on KSZ87xx.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Fixes: 46558d601c ("net: dsa: microchip: Initial SPI regmap support")
Fixes: 255b59ad0d ("net: dsa: microchip: Factor out regmap config generation into common header")
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port does not have a PHY connected to it. So calling
phy_support_asym_pause() results in an Opps. As with other DSA
drivers, add a guard that the port is a user port.
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header file for Distributed Switch Architecture drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch corrects the SPDX License Identifier style
in header file for Broadcom BCM53xx managed switch driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If CONFIG_NET_DSA_SJA1105_TAS=y and CONFIG_NET_SCH_TAPRIO=n,
below error can be found:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x318): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x590): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x610): undefined reference to `taprio_offload_free'
make: *** [vmlinux] Error 1
sja1105_tas needs tc-taprio, so this patch add the dependency for it.
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This qdisc offload is the closest thing to what the SJA1105 supports in
hardware for time-based egress shaping. The switch core really is built
around SAE AS6802/TTEthernet (a TTTech standard) but can be made to
operate similarly to IEEE 802.1Qbv with some constraints:
- The gate control list is a global list for all ports. There are 8
execution threads that iterate through this global list in parallel.
I don't know why 8, there are only 4 front-panel ports.
- Care must be taken by the user to make sure that two execution threads
never get to execute a GCL entry simultaneously. I created a O(n^4)
checker for this hardware limitation, prior to accepting a taprio
offload configuration as valid.
- The spec says that if a GCL entry's interval is shorter than the frame
length, you shouldn't send it (and end up in head-of-line blocking).
Well, this switch does anyway.
- The switch has no concept of ADMIN and OPER configurations. Because
it's so simple, the TAS settings are loaded through the static config
tables interface, so there isn't even place for any discussion about
'graceful switchover between ADMIN and OPER'. You just reset the
switch and upload a new OPER config.
- The switch accepts multiple time sources for the gate events. Right
now I am using the standalone clock source as opposed to PTP. So the
base time parameter doesn't really do much. Support for the PTP clock
source will be added in a future series.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support tc-taprio offload, the TTEthernet egress scheduling
core registers must be made visible through the static interface.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the per-port egress flooding control for
both Unicast and Multicast traffic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9567 7-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9567 supports both SPI and I2C. Oddly the
ksz9567 is already in the device tree binding documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
[george.mccollister@gmail.com: bring up to date, use ksz_common regmap macros]
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure
a port's Layer 2 Policy Control List (PCL) via ethtool.
Currently only dropping frames based on MAC Destination or Source
Address (including the option VLAN parameter) is supported.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .port_set_policy operation to configure a port's
Policy Control List, based on mapping such as DA, SA, Etype and so on.
Models similar to 88E6352 and 88E6390 are supported at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell has different values for the state of a MAC address,
depending on its multicast bit. This patch completes the definitions
for these states.
At the same time, use 0 which is intuitive enough and simplifies the
code a bit, instead of the UC or MC unused value.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for port 5.
Port 5 can muxed/interface to:
- internal 5th GMAC of the switch; can be used as 2nd CPU port or as
extra port with an external phy for a 6th ethernet port.
- internal PHY of port 0 or 4; Used in most applications so that port 0
or 4 is the WAN port and interfaces with the 2nd GMAC of the SOC.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mt7530 to PHYLINK API
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.
Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.
Fixes: b759f528ca ("net: dsa: mv88e6xxx: enable SERDES after setup")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 7a3007d22e ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 17deaf5cb3 ("net: dsa:
mv88e6xxx: create serdes_get_lane chip operation").
The .serdes_get_lane implementations access the CMODE of a port,
even though it is cached at the moment, it is safer to call them
after the mutex is locked, not before.
At the same time, check for an eventual error and return IRQ_DONE,
instead of blindly ignoring it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch barely supports traffic I/O, and it does that by repurposing
VLANs when there is no bridge that is taking control of them.
Letting DSA declare this netdev feature as supported (see
dsa_slave_create) would mean that VLAN sub-interfaces created on sja1105
switch ports will be hardware offloaded. That means that
net/8021q/vlan_core.c would install the VLAN into the filter tables of
the switch, potentially interfering with the tag_8021q VLANs.
We need to prevent that from happening and not let the 8021q core
offload VLANs to the switch hardware tables. In vlan_filtering=0 modes
of operation, the switch ports can pass through VLAN-tagged frames with
no problem.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 binding does not specify that the CPU port should have
properties mandatory for successfully instantiating a PHYLINK object. As
such, there will be missing properties (including fixed-link) and when
attempting to validate and later configure link modes, we will have an
incorrect set of parameters (interface, speed, duplex).
Simply prevent the CPU port from being configured through PHYLINK since
bcm_sf2_imp_setup() takes care of that already.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xxx_serdes_power is only called after driver setup,
we can wrap the SERDES IRQ code directly within it for clarity.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SERDES is powered on for CPU and DSA ports and powered down for unused
ports at setup time. But now that DSA calls mv88e6xxx_port_enable
and mv88e6xxx_port_disable for all ports, the SERDES power can now
be handled after setup inconditionally for all ports.
Using the port enable and disable callbacks also have the benefit to
handle the SERDES IRQ for non user ports as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling a port, that is not for the driver to decide what to
do with the STP state. This is already handled by the DSA layer.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_smi_direct_wait routine is used to wait on indirect
registers access. It is of no exception and must delay between read
attempts, like other wait routines.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_smi_direct_wait function is only used to check
the 16th bit of the (16-bit) SMI Command register. But the bit shift
operation is not enough if we eventually use this function to check
other bits, thus replace it with a mask.
Fixes: e7ba0fad9c ("net: dsa: mv88e6xxx: refine SMI support")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.
The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut