A notifier is used to track route changes in the kernel. If a change is
made to a route that is offloaded to fw then an update is sent to the NIC.
The driver tracks all routes that are offloaded to determine if a kernel
change is of interest.
Extend the notifier to track IPv6 route changes and create a new list that
stores offloaded IPv6 routes. Modify the IPv4 route helper functions to
accept varying address lengths. This way, the same core functions can be
used to handle IPv4 and IPv6.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fw does not know the next hop for an IPv6 tunnel, it sends a request
to the driver.
Handle this request by doing a route lookup on the IPv6 address and
offloading the next hop to the fw neighbour table.
Similar functions already exist to handle IPv4 no neighbour requests. To
avoid confusion, append these functions with the _ipv4 tag. There is no
change in functionality with this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 set tunnel action allows the setting of tunnel metadata such as
the TTL and ToS values. The pre-tunnel action includes the destination IP
address and is used to calculate the next hop from from the neighbour
table.
Much of the IPv4 tunnel actions can be reused for IPv6 tunnels. Change the
names of associated functions and structs to remove the IPv4 identifier
and make minor modifcations to support IPv6 tunnel actions.
Ensure the pre-tunnel action contains the IPv6 address along with an
identifying flag when an IPv6 tunnel action is required.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fw requires a list of IPv6 addresses that are used as tunnel endpoints to
enable correct decap of tunneled packets.
Store a list of IPv6 endpoints used in rules with a ref counter to track
how many times it is in use. Offload the entire list any time a new IPv6
address is added or when an address is removed (ref count is 0).
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 tunnel matches are now supported by firmware. Modify the NFP driver
to compile these match rules. IPv6 matches are handled similar to IPv4
tunnels with the difference the address length. The type of tunnel is
indicated by the same bitmap that is used in IPv4 with an extra bit
signifying that the IPv6 variation should be used.
Only compile IPv6 tunnel matches when the fw features symbol indicated
that they are compatible with the currently loaded fw.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 UDP and GRE tunnel match rule compile helpers share functions for
compiling fields such as IP addresses. However, they handle fields such
tunnel IDs differently.
Create new helper functions for compiling GRE and UDP tunnel key data.
This is in preparation for supporting IPv6 tunnels where these new
functions can be reused.
This patch does not change functionality.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel 5.1, the flow offload API was introduced along with a helper
function to extract the flow_rule from the TC offload struct. Each of the
match helper functions are passed the offload struct and extract the flow
rule to a local variable.
Simplify the code while also removing the extra compat and local variable
calls by extracting the rule once in the main match handler, and passing
a reference to the rule direct to each helper.
This patch does not change driver functionality.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hdlcdrv_register, failure to register the driver causes a crash.
The three callers of hdlcdrv_register all pass valid pointers and
do not fail. The patch eliminates the unnecessary BUG_ON assertion.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In s3fwrn5_fw_recv_frame, if fw_info->rsp is not empty, the
current code causes a crash via BUG_ON. However, s3fwrn5_fw_send_msg
does not crash in such a scenario. The patch replaces the BUG_ON
by returning the error to the callers and frees up skb.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: macb: fix probing of PHY not described in the dt
The macb Ethernet driver supports various ways of referencing its
network PHY. When a device tree is used the PHY can be referenced with
a phy-handle or, if connected to its internal MDIO bus, described in
a child node. Some platforms omitted the PHY description while
connecting the PHY to the internal MDIO bus and in such cases the MDIO
bus has to be scanned "manually" by the macb driver.
Prior to the phylink conversion the driver registered the MDIO bus with
of_mdiobus_register and then in case the PHY couldn't be retrieved
using dt or using phy_find_first (because registering an MDIO bus with
of_mdiobus_register masks all PHYs) the macb driver was "manually"
scanning the MDIO bus (like mdiobus_register does). The phylink
conversion did break this particular case but reimplementing the manual
scan of the bus in the macb driver wouldn't be very clean. The solution
seems to be registering the MDIO bus based on if the PHYs are described
in the device tree or not.
There are multiple ways to do this, none is perfect. I chose to check if
any of the child nodes of the macb node was a network PHY and based on
this to register the MDIO bus with the of_ helper or not. The drawback
is boards referencing the PHY through phy-handle, would scan the entire
MDIO bus of the macb at boot time (as the MDIO bus would be registered
with mdiobus_register). For this solution to work properly
of_mdiobus_child_is_phy has to be exported, which means the patch doing
so has to be backported to -stable as well.
Another possible solution could have been to simply check if the macb
node has a child node by counting its sub-nodes. This isn't techically
perfect, as there could be other sub-nodes (in practice this should be
fine, fixed-link being taken care of in the driver). We could also
simply s/of_mdiobus_register/mdiobus_register/ but that could break
boards using the PHY description in child node as a selector (which
really would be not a proper way to do this...).
The real issue here being having PHYs not described in the dt but we
have dt backward compatibility, so we have to live with that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case where the PHY isn't described in the device
tree. This is due to the way the MDIO bus is registered in the driver:
whether the PHY is described in the device tree or not, the bus is
registered through of_mdiobus_register. The function masks all the PHYs
and only allow probing the ones described in the device tree. Prior to
the Phylink conversion this was also done but later on in the driver
the MDIO bus was manually scanned to circumvent the fact that the PHY
wasn't described.
This patch fixes it in a proper way, by registering the MDIO bus based
on if the PHY attached to a given interface is described in the device
tree or not.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports of_mdiobus_child_is_phy, allowing to check if a child
node is a network PHY.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently, at boot time, the comphys are enabled. For firmware
compatibility reasons, the comphy driver does not power down the
comphys at boot. Consequently, the ethernet comphys are left active
until the network interfaces are brought through an up/down cycle.
If the port is never used, the port wastes power needlessly. Arrange
for the ethernet comphys to be cycled by the mvpp2 driver as if the
interface went through an up/down cycle during driver probe, thereby
powering them down.
This saves:
270mW per 10G SFP+ port on the Macchiatobin Single Shot (eth0/eth1)
370mW per 10G PHY port on the Macchiatobin Double Shot (eth0/eth1)
160mW on the SFP port on either Macchiatobin flavour (eth3)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report a rate-limited error if we fail to read the SFP soft status,
and preserve the current status in that case. This avoids I2C bus
errors from triggering a link flap.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compare functions of the histogram code would be specific for the size
of the value being compared (byte, short, int, long long). It would
reference the value from the array via the type of the compare, but the
value was stored in a 64 bit number. This is fine for little endian
machines, but for big endian machines, it would end up comparing zeros or
all ones (depending on the sign) for anything but 64 bit numbers.
To fix this, first derference the value as a u64 then convert it to the type
being compared.
Link: http://lkml.kernel.org/r/20191211103557.7bed6928@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 08d43a5fa0 ("tracing: Add lock-free tracing_map")
Acked-by: Tom Zanussi <zanussi@kernel.org>
Reported-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-19
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 269 insertions(+), 108 deletions(-).
The main changes are:
1) Fix lack of synchronization between xsk wakeup and destroying resources
used by xsk wakeup, from Maxim Mikityanskiy.
2) Fix pruning with tail call patching, untrack programs in case of verifier
error and fix a cgroup local storage tracking bug, from Daniel Borkmann.
3) Fix clearing skb->tstamp in bpf_redirect() when going from ingress to
egress which otherwise cause issues e.g. on fq qdisc, from Lorenz Bauer.
4) Fix compile warning of unused proc_dointvec_minmax_bpf_restricted() when
only cBPF is present, from Alexander Lobakin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand dummy prog generation such that we can easily check on return
codes and add few more test cases to make sure we keep on tracking
pruning behavior.
# ./test_verifier
[...]
#1066/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK
#1067/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK
Summary: 1580 PASSED, 0 SKIPPED, 0 FAILED
Also verified that JIT dump of added test cases looks good.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/df7200b6021444fd369376d227de917357285b65.1576789878.git.daniel@iogearbox.net
While testing Cilium with /unreleased/ Linus' tree under BPF-based NodePort
implementation, I noticed a strange BPF SNAT engine behavior from time to
time. In some cases it would do the correct SNAT/DNAT service translation,
but at a random point in time it would just stop and perform an unexpected
translation after SYN, SYN/ACK and stack would send a RST back. While initially
assuming that there is some sort of a race condition in BPF code, adding
trace_printk()s for debugging purposes at some point seemed to have resolved
the issue auto-magically.
Digging deeper on this Heisenbug and reducing the trace_printk() calls to
an absolute minimum, it turns out that a single call would suffice to
trigger / not trigger the seen RST issue, even though the logic of the
program itself remains unchanged. Turns out the single call changed verifier
pruning behavior to get everything to work. Reconstructing a minimal test
case, the incorrect JIT dump looked as follows:
# bpftool p d j i 11346
0xffffffffc0cba96c:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff89cc74e85800,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff89cc74e85800,%rsi
49: mov -0x224(%rbp),%eax
4f: cmp $0x20,%eax
52: ja 0x0000000000000062
54: add $0x1,%eax
57: mov %eax,-0x224(%rbp)
5d: jmpq 0xffffffffffff6911
62: mov $0x1,%eax
[...]
Hence, unexpectedly, JIT emitted a direct jump even though retpoline based
one would have been needed since in line 2c and 3a we have different slot
keys in BPF reg r3. Verifier log of the test case reveals what happened:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=inv(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0xffff89cc74d54a00
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=inv13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0xffff89cc74d54a00
11: safe
processed 13 insns (limit 1000000) [...]
Second branch is pruned by verifier since considered safe, but issue is that
record_func_key() couldn't have seen the index in line 3a and therefore
decided that emitting a direct jump at this location was okay.
Fix this by reusing our backtracking logic for precise scalar verification
in order to prevent pruning on the slot key. This means verifier will track
content of r3 all the way backwards and only prune if both scalars were
unknown in state equivalence check and therefore poisoned in the first place
in record_func_key(). The range is [x,x] in record_func_key() case since
the slot always would have to be constant immediate. Correct verification
after fix:
0: (b7) r0 = 14
1: (73) *(u8 *)(r1 +48) = r0
2: (71) r0 = *(u8 *)(r1 +48)
3: (15) if r0 == 0xd goto pc+4
R0_w=invP(id=0,umax_value=255,var_off=(0x0; 0xff)) R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (b7) r3 = 0
5: (18) r2 = 0x0
7: (05) goto pc+3
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
from 3 to 8: R0_w=invP13 R1=ctx(id=0,off=0,imm=0) R10=fp0
8: (b7) r3 = 2
9: (18) r2 = 0x0
11: (85) call bpf_tail_call#12
12: (b7) r0 = 1
13: (95) exit
processed 15 insns (limit 1000000) [...]
And correct corresponding JIT dump:
# bpftool p d j i 11
0xffffffffc0dc34c4:
[...]
21: movzbq 0x30(%rdi),%rax
26: cmp $0xd,%rax
2a: je 0x000000000000003a
2c: xor %edx,%edx
2e: movabs $0xffff9928b4c02200,%rsi
38: jmp 0x0000000000000049
3a: mov $0x2,%edx
3f: movabs $0xffff9928b4c02200,%rsi
49: cmp $0x4,%rdx
4d: jae 0x0000000000000093
4f: and $0x3,%edx
52: mov %edx,%edx
54: cmp %edx,0x24(%rsi)
57: jbe 0x0000000000000093
59: mov -0x224(%rbp),%eax
5f: cmp $0x20,%eax
62: ja 0x0000000000000093
64: add $0x1,%eax
67: mov %eax,-0x224(%rbp)
6d: mov 0x110(%rsi,%rdx,8),%rax
75: test %rax,%rax
78: je 0x0000000000000093
7a: mov 0x30(%rax),%rax
7e: add $0x19,%rax
82: callq 0x000000000000008e
87: pause
89: lfence
8c: jmp 0x0000000000000087
8e: mov %rax,(%rsp)
92: retq
93: mov $0x1,%eax
[...]
Also explicitly adding explicit env->allow_ptr_leaks to fixup_bpf_calls() since
backtracking is enabled under former (direct jumps as well, but use different
test). In case of only tracking different map pointers as in c93552c443 ("bpf:
properly enforce index mask to prevent out-of-bounds speculation"), pruning
cannot make such short-cuts, neither if there are paths with scalar and non-scalar
types as r3. mark_chain_precision() is only needed after we know that
register_is_const(). If it was not the case, we already poison the key on first
path and non-const key in later paths are not matching the scalar range in regsafe()
either. Cilium NodePort testing passes fine as well now. Note, released kernels
not affected.
Fixes: d2e4c1e6c2 ("bpf: Constant map key tracking for prog array pokes")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/ac43ffdeb7386c5bd688761ed266f3722bb39823.1576789878.git.daniel@iogearbox.net
Russell King says:
====================
phylib consolidation
Over the last few releases, there has been a push to clean up and
consolidate the phylib code. Some cases have been missed, and this
series catches those cases.
1. Remove redundant .aneg_done initialisers; calling genphy_aneg_done()
for clause 22 PHYs is the default when .aneg_done is not set.
2. Some PHY drivers manually set phydev->pause and phydev->asym_pause,
but we have a helper for this - phy_resolve_aneg_pause(), introduced
in 2d880b8709 ("net: phy: extract pause mode"). Use this in the
lxt, marvell and uPD60620 drivers.
Incidentally, this brings up the question whether marvell fiber mode
is correctly interpreting and advertising the pause parameters.
3. Add a genphy_check_and_restart_aneg() helper, which complements the
clause 45 version of this. This will be useful for PHY drivers that
open code this logic (e.g. marvell.c)
4. Add a genphy_read_status_fixed() helper to read the fixed-mode
status from a clause 22 PHY. lxt and marvell both contain copies
of this code, so convert them over.
5. Arrange marvell driver to use genphy_read_lpa() for copper mode.
This needs some rearrangement of the code in
marvell_read_status_page_an(), but preserves using the PHY specific
status register to derive the current negotiation results.
6. Simplify the marvell driver so we can use the
genphy_read_status_fixed() helper directly rather than
marvell_read_status_page_fixed().
7. Use positive logic in the marvell driver to determine the link
state, and get rid of the REGISTER_LINK_STATUS definition; we
already have a definition for this.
8. The marvell driver reads the PHY specific status register multiple
times when determining the status: once in marvell_update_link()
and again in marvell_read_status_page_an(). This is a waste;
rearrange to read the status register once, and pass its value into
marvell_read_status_page_an(). We preserve using
genphy_update_link() for the copper side.
9. The marvell driver was using private clause 37 definitions, but we
have clause 37 definitions in uapi/linux/mii.h. Use the generic
definitions.
10. Switch the marvell driver to use phy_modify_changed() to modify
the fiber advertisement.
11. Switch the marvell driver to use genphy_check_and_restart_aneg()
introduced above rather than open-coding this functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper to check and restart autonegotiation for the marvell
fiber page negotiation setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_modify_changed() to change the fiber advertisement register
rather than open coding this functionality.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing clause 37 advertising/link partner definitions rather than
private ones for the advertisement registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_read_status_page_an() always reads the PHY status register, but
marvell_update_link() has already done this. Rather than wastefully
reading the register twice in quick succession, read it once in
marvell_read_status_page() and use the result for both.
This makes marvell_update_link() rather pointless, so move it into
marvell_read_status_page().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using negative logic:
if (there is no link)
set link = 0
else
set link = 1
use the more natural positive logic:
if (there is link)
set link = 1
else
set link = 0
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialisation of the link partner state earlier, inside
marvell_read_status_page(), so we don't have the same initialisation
scattered amongst the other files. This is in a similar place to
the genphy implementation, so would result in the same behaviour if
a PHY read error occurs.
This allows us to get rid of marvell_read_status_page_fixed(), which
became a pointless wrapper around genphy_read_status_fixed().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the Marvell PHY driver to use genphy_read_lpa() rather than
open-coding this functionality.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two drivers and generic code which contain exactly the same
code to read the status of a PHY operating without autonegotiation
enabled. Rather than duplicate this code, provide a helper to read
this information.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for restarting autonegotiation(), similar to the clause 45
variant. Use it in __genphy_config_aneg()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers code their own version of this, working from the LPA
register, after setting the ethtool link partner advertisement bitmask.
Use the generic function instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove initialisers that set .aneg_done to genphy_aneg_done - this is
the default for clause 22 PHYs, so the initialiser is redundant.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.6. Major changes:
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
The FIELD_SIZEOF() macro was redundant, and is being removed from the
kernel. Since commit c593642c8b ("treewide: Use sizeof_field() macro")
this is one of the last users of the old macro, so replace it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
proc_dointvec_minmax_bpf_restricted() has been firstly introduced
in commit 2e4a30983b ("bpf: restrict access to core bpf sysctls")
under CONFIG_HAVE_EBPF_JIT. Then, this ifdef has been removed in
ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv
allocations"), because a new sysctl, bpf_jit_limit, made use of it.
Finally, this parameter has become long instead of integer with
fdadd04931 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
and thus, a new proc_dolongvec_minmax_bpf_restricted() has been
added.
With this last change, we got back to that
proc_dointvec_minmax_bpf_restricted() is used only under
CONFIG_HAVE_EBPF_JIT, but the corresponding ifdef has not been
brought back.
So, in configurations like CONFIG_BPF_JIT=y && CONFIG_HAVE_EBPF_JIT=n
since v4.20 we have:
CC net/core/sysctl_net_core.o
net/core/sysctl_net_core.c:292:1: warning: ‘proc_dointvec_minmax_bpf_restricted’ defined but not used [-Wunused-function]
292 | proc_dointvec_minmax_bpf_restricted(struct ctl_table *table, int write,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Suppress this by guarding it with CONFIG_HAVE_EBPF_JIT again.
Fixes: fdadd04931 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191218091821.7080-1-alobakin@dlink.ru
Three of the WMI command handlers were not casting to the right data type.
Lets make the code consistent with the other handlers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
set_cqm_rssi_config() is used by the kernel to configure connection
quality monitor RSSI threshold.
wil6210 uses WMI_SET_LINK_MONITOR_CMDID to set the RSSI threshold to
FW which in turn reports RSSI threshold changes with
WMI_LINK_MONITOR_EVENTID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wil6210 AP has a separate ring for transmitting multicast packets,
multicast packets are transmitted without an ack from the receiver side.
Therefore, 802.11 spec defines some low MCS rates for multicat packets.
However, there is no guarantee that these packets were really received
and handled on the client side.
Some applications that rely on multicast packets, may prefer to
transmit these packets as a unicast to ensure reliability, and also
to ensure better performance with high MCS rates.
multicast to unicast is done by duplicating multicast packets to all
clients and changing the DA (multicast) to the MAC address of the
client.
see NL80211_CMD_SET_MULTICAST_TO_UNICAST for more info.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix incorrect definitions of MAC ID bits inside Rx status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ucode_debug memory region defined as 4K bytes. Fix this according to
Talyn device memory map.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
max_assoc_sta can receive values (from the user or from the FW)
that are higher than WIL6210_MAX_CID.
Verify that cid doesn't exceed the upper bound of WIL6210_MAX_CID.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some crash dump cases mem_lock is already taken, error
returns and crash dump copy fails.
In this case wait until mem_lock available instead of failing
the operation.
Also take the mem_lock for writing to prevent other threads from
altering the state of the device while collecting crash dump.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mem_lock is taken for the entire wil_reset().
Optimize this by taking mem_lock just before device is
being reset and release the lock after FW download.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump all the Rx status message on different errors to allow more
visibility of the case.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/Kconfig.debug: fix some messed up configurations
mm: vmscan: protect shrinker idr replace with CONFIG_MEMCG
kasan: don't assume percpu shadow allocations will succeed
kasan: use apply_to_existing_page_range() for releasing vmalloc shadow
mm/memory.c: add apply_to_existing_page_range() helper
kasan: fix crashes on access to memory mapped by vm_map_ram()
Fix a problem related to CPU offline/online and cpufreq governors
that in some system configurations may lead to a system-wide
deadlock during CPU online.
-----BEGIN PGP SIGNATURE-----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=+MQE
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a problem related to CPU offline/online and cpufreq governors that
in some system configurations may lead to a system-wide deadlock
during CPU online"
* tag 'pm-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid leaving stale IRQ work items during CPU offline
Alex Lyakas reported[1] that mounting an xfs filesystem with new sunit
and swidth values could cause xfs_repair to fail loudly. The problem
here is that repair calculates the where mkfs should have allocated the
root inode, based on the superblock geometry. The allocation decisions
depend on sunit, which means that we really can't go updating sunit if
it would lead to a subsequent repair failure on an otherwise correct
filesystem.
Port from xfs_repair some code that computes the location of the root
inode and teach mount to skip the ondisk update if it would cause
problems for repair. Along the way we'll update the documentation,
provide a function for computing the minimum AGFL size instead of
open-coding it, and cut down some indenting in the mount code.
Note that we allow the mount to proceed (and new allocations will
reflect this new geometry) because we've never screened this kind of
thing before. We'll have to wait for a new future incompat feature to
enforce correct behavior, alas.
Note that the geometry reporting always uses the superblock values, not
the incore ones, so that is what xfs_info and xfs_growfs will report.
[1] https://lore.kernel.org/linux-xfs/20191125130744.GA44777@bfoster/T/#m00f9594b511e076e2fcdd489d78bc30216d72a7d
Reported-by: Alex Lyakas <alex@zadara.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
If the administrator provided a sunit= mount option, we need to validate
the raw parameter, convert the mount option units (512b blocks) into the
internal unit (fs blocks), and then validate that the (now cooked)
parameter doesn't screw anything up on disk. The incore inode geometry
computation can depend on the new sunit option, but a subsequent patch
will make validating the cooked value depends on the computed inode
geometry, so break the sunit update into two steps.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor xfs_alloc_min_freelist to accept a NULL @pag argument, in which
case it returns the largest possible minimum length. This will be used
in an upcoming patch to compute the length of the AGFL at mkfs time.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Prepare to resync the userspace libxfs with the kernel libxfs. There
were a few things I missed -- a couple of static inline directory
functions that have to be exported for xfs_repair; a couple of directory
naming functions that make porting much easier if they're /not/ static
inline; and a u16 usage that should have been uint16_t.
None of these things are bugs in their own right; this just makes
porting xfsprogs easier.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
The xfs_log_item flags were converted to atomic bitops as of commit
22525c17ed ("xfs: log item flags are racy"). The assert check for
AIL presence in xfs_buf_item_relse() still uses the old value based
check. This likely went unnoticed as XFS_LI_IN_AIL evaluates to 0
and causes the assert to unconditionally pass. Fix up the check.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Fixes: 22525c17ed ("xfs: log item flags are racy")
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
John Hurley